@article{CastilhoHochleitnerWilsonetal.2018,
  author    = {Castilho, Miguel and Hochleitner, Gernot and Wilson, Wouter and van Rietbergen, Bert and Dalton, Paul D. and Groll, J{\"u}rgen and Malda, Jos and Ito, Keita},
  title     = {Mechanical behavior of a soft hydrogel reinforced with three-dimensional printed microfibre scaffolds},
  series = {Scientific Reports},
  volume    = {8},
  journal   = {Scientific Reports},
  doi       = {10.1038/s41598-018-19502-y},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-222280},
  year      = {2018},
  abstract  = {Reinforcing hydrogels with micro-fibre scaffolds obtained by a Melt-Electrospinning Writing (MEW) process has demonstrated great promise for developing tissue engineered (TE) constructs with mechanical properties compatible to native tissues. However, the mechanical performance and reinforcement mechanism of the micro-fibre reinforced hydrogels is not yet fully understood. In this study, FE models, implementing material properties measured experimentally, were used to explore the reinforcement mechanism of fibre-hydrogel composites. First, a continuum FE model based on idealized scaffold geometry was used to capture reinforcement effects related to the suppression of lateral gel expansion by the scaffold, while a second micro-FE model based on micro-CT images of the real construct geometry during compaction captured the effects of load transfer through the scaffold interconnections. Results demonstrate that the reinforcement mechanism at higher scaffold volume fractions was dominated by the load carrying-ability of the fibre scaffold interconnections, which was much higher than expected based on testing scaffolds alone because the hydrogel provides resistance against buckling of the scaffold. We propose that the theoretical understanding presented in this work will assist the design of more effective composite constructs with potential applications in a wide range of TE conditions.},
  language  = {en}
}
@article{JanzenBakirciFaberetal.2022,
  author    = {Janzen, Dieter and Bakirci, Ezgi and Faber, Jessica and Andrade Mier, Mateo and Hauptstein, Julia and Pal, Arindam and Forster, Leonard and Hazur, Jonas and Boccaccini, Aldo R. and Detsch, Rainer and Teßmar, J{\"o}rg and Budday, Silvia and Blunk, Torsten and Dalton, Paul D. and Villmann, Carmen},
  title     = {Reinforced Hyaluronic Acid-Based Matrices Promote 3D Neuronal Network Formation},
  series = {Advanced Healthcare Materials},
  volume    = {11},
  journal   = {Advanced Healthcare Materials},
  number    = {21},
  doi       = {10.1002/adhm.202201826},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-318682},
  year      = {2022},
  abstract  = {3D neuronal cultures attempt to better replicate the in vivo environment to study neurological/neurodegenerative diseases compared to 2D models. A challenge to establish 3D neuron culture models is the low elastic modulus (30-500 Pa) of the native brain. Here, an ultra-soft matrix based on thiolated hyaluronic acid (HA-SH) reinforced with a microfiber frame is formulated and used. Hyaluronic acid represents an essential component of the brain extracellular matrix (ECM). Box-shaped frames with a microfiber spacing of 200 µm composed of 10-layers of poly(ɛ-caprolactone) (PCL) microfibers (9.7 ± 0.2 µm) made via melt electrowriting (MEW) are used to reinforce the HA-SH matrix which has an elastic modulus of 95 Pa. The neuronal viability is low in pure HA-SH matrix, however, when astrocytes are pre-seeded below this reinforced construct, they significantly support neuronal survival, network formation quantified by neurite length, and neuronal firing shown by Ca\(^{2+}\) imaging. The astrocyte-seeded HA-SH matrix is able to match the neuronal viability to the level of Matrigel, a gold standard matrix for neuronal culture for over two decades. Thus, this 3D MEW frame reinforced HA-SH composite with neurons and astrocytes constitutes a reliable and reproducible system to further study brain diseases.},
  language  = {en}
}
@article{KadeBakirciTandonetal.2022,
  author    = {Kade, Juliane C. and Bakirci, Ezgi and Tandon, Biranche and Gorgol, Danila and Mrlik, Miroslav and Luxenhofer, Robert and Dalton, Paul D.},
  title     = {The Impact of Including Carbonyl Iron Particles on the Melt Electrowriting Process},
  series = {Macromolecular Materials and Engineering},
  volume    = {307},
  journal   = {Macromolecular Materials and Engineering},
  number    = {12},
  issn      = {1438-7492},
  doi       = {10.1002/mame.202200478},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-318482},
  year      = {2022},
  abstract  = {Melt electrowriting, a high-resolution additive manufacturing technique, is used in this study to process a magnetic polymer-based blend for the first time. Carbonyl iron (CI) particles homogenously distribute into poly(vinylidene fluoride) (PVDF) melts to result in well-defined, highly porous structures or scaffolds comprised of fibers ranging from 30 to 50 µm in diameter. This study observes that CI particle incorporation is possible up to 30 wt\% without nozzle clogging, albeit that the highest concentration results in heterogeneous fiber morphologies. In contrast, the direct writing of homogeneous PVDF fibers with up to 15 wt\% CI is possible. The fibers can be readily displaced using magnets at concentrations of 1 wt\% and above. Combined with good viability of L929 CC1 cells using Live/Dead imaging on scaffolds for all CI concentrations indicates that these formulations have potential for the usage in stimuli-responsive applications such as 4D printing.},
  language  = {en}
}
@article{HaagSonnleitnerLangetal.2022,
  author    = {Haag, Hannah and Sonnleitner, David and Lang, Gregor and Dalton, Paul D.},
  title     = {Melt electrowriting to produce microfiber fragments},
  series = {Polymers for Advanced Technologies},
  volume    = {33},
  journal   = {Polymers for Advanced Technologies},
  number    = {6},
  issn      = {1042-7147},
  doi       = {10.1002/pat.5641},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-318465},
  pages     = {1989 -- 1992},
  year      = {2022},
  language  = {en}
}
@article{BoehmTandonHrynevichetal.2022,
  author    = {B{\"o}hm, Christoph and Tandon, Biranche and Hrynevich, Andrei and Teßmar, J{\"o}rg and Dalton, Paul D.},
  title     = {Processing of Poly(lactic-co-glycolic acid) Microfibers via Melt Electrowriting},
  series = {Macromolecular Chemistry and Physics},
  volume    = {223},
  journal   = {Macromolecular Chemistry and Physics},
  number    = {5},
  doi       = {10.1002/macp.202100417},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-318444},
  year      = {2022},
  abstract  = {Polymers sensitive to thermal degradation include poly(lactic-co-glycolic acid) (PLGA), which is not yet processed via melt electrowriting (MEW). After an initial period of instability where mean fiber diameters increase from 20.56 to 27.37 µm in 3.5 h, processing stabilizes through to 24 h. The jet speed, determined using critical translation speed measurements, also reduces slightly in this 3.5 h period from 500 to 433 mm min\(^{-1}\) but generally remains constant. Acetyl triethyl citrate (ATEC) as an additive decreases the glass transition temperature of PLGA from 49 to 4 °C, and the printed ATEC/PLGA fibers exhibits elastomeric behavior upon handling. Fiber bundles tested in cyclic mechanical testing display increased elasticity with increasing ATEC concentration. The processing temperature of PLGA also reduces from 165 to 143 °C with increase in ATEC concentration. This initial window of unstable direct writing seen with neat PLGA can also be impacted through the addition of 10-wt\% ATEC, producing fiber diameters of 14.13 ± 1.69 µm for the first 3.5 h of heating. The investigation shows that the initial changes to the PLGA direct-writing outcomes seen in the first 3.5 h are temporary and that longer times result in a more stable MEW process.},
  language  = {en}
}
@article{KadeOttoLuxenhoferetal.2021,
  author    = {Kade, Juliane C. and Otto, Paul F. and Luxenhofer, Robert and Dalton, Paul D.},
  title     = {Melt electrowriting of poly(vinylidene difluoride) using a heated collector},
  series = {Polymers for Advanced Technologies},
  volume    = {32},
  journal   = {Polymers for Advanced Technologies},
  number    = {12},
  issn      = {1042-7147},
  doi       = {10.1002/pat.5463},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-318493},
  pages     = {4951 -- 4955},
  year      = {2021},
  abstract  = {Previous research on the melt electrowriting (MEW) of poly(vinylidene difluoride) (PVDF) resulted in electroactive fibers, however, printing more than five layers is challenging. Here, we investigate the influence of a heated collector to adjust the solidification rate of the PVDF jet so that it adheres sufficiently to each layer. A collector temperature of 110°C is required to improve fiber processing, resulting in a total of 20 fiber layers. For higher temperatures and higher layers, an interesting phenomenon occurred, where the intersection points of the fibers coalesced into periodic spheres of diameter 206 ± 52 μm (26G, 150°C collector temperature, 2000 mm/min, 10 layers in x- and y-direction).The heated collector is an important component of a MEW printer that allows polymers with a high melting point to be processable with increased layers.},
  language  = {en}
}
@article{WielandStrisselSchorleetal.2021,
  author    = {Wieland, Annalena and Strissel, Pamela L. and Schorle, Hannah and Bakirci, Ezgi and Janzen, Dieter and Beckmann, Matthias W. and Eckstein, Markus and Dalton, Paul D. and Strick, Reiner},
  title     = {Brain and breast cancer cells with PTEN loss of function reveal enhanced durotaxis and RHOB dependent amoeboid migration utilizing 3D scaffolds and aligned microfiber tracts},
  series = {Cancers},
  volume    = {13},
  journal   = {Cancers},
  number    = {20},
  issn      = {2072-6694},
  doi       = {10.3390/cancers13205144},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-248443},
  year      = {2021},
  abstract  = {Background: Glioblastoma multiforme (GBM) and metastatic triple-negative breast cancer (TNBC) with PTEN mutations often lead to brain dissemination with poor patient outcome, thus new therapeutic targets are needed. To understand signaling, controlling the dynamics and mechanics of brain tumor cell migration, we implemented GBM and TNBC cell lines and designed 3D aligned microfibers and scaffolds mimicking brain structures. Methods: 3D microfibers and scaffolds were printed using melt electrowriting. GBM and TNBC cell lines with opposing PTEN genotypes were analyzed with RHO-ROCK-PTEN inhibitors and PTEN rescue using live-cell imaging. RNA-sequencing and qPCR of tumor cells in 3D with microfibers were performed, while scanning electron microscopy and confocal microscopy addressed cell morphology. Results: In contrast to the PTEN wildtype, GBM and TNBC cells with PTEN loss of function yielded enhanced durotaxis, topotaxis, adhesion, amoeboid migration on 3D microfibers and significant high RHOB expression. Functional studies concerning RHOB-ROCK-PTEN signaling confirmed the essential role for the above cellular processes. Conclusions: This study demonstrates a significant role of the PTEN genotype and RHOB expression for durotaxis, adhesion and migration dependent on 3D. GBM and TNBC cells with PTEN loss of function have an affinity for stiff brain structures promoting metastasis. 3D microfibers represent an important tool to model brain metastasizing tumor cells, where RHO-inhibitors could play an essential role for improved therapy.},
  language  = {en}
}
@article{KadeTandonWeichholdetal.2021,
  author    = {Kade, Juliane C. and Tandon, Biranche and Weichhold, Jan and Pisignano, Dario and Persano, Luana and Luxenhofer, Robert and Dalton, Paul D.},
  title     = {Melt electrowriting of poly(vinylidene fluoride-co-trifluoroethylene)},
  series = {Polymer International},
  volume    = {70},
  journal   = {Polymer International},
  number    = {12},
  doi       = {10.1002/pi.6272},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-257654},
  pages     = {1725-1732},
  year      = {2021},
  abstract  = {Poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-co-TrFE)) is an electroactive polymer with growing interest for applications in biomedical materials and flexible electronics. In this study, a solvent-free additive manufacturing technique called melt electrowriting (MEW) has been utilized to fabricate well-defined microperiodic structures of the copolymer (P(VDF-co-TrFE)). MEW of the highly viscous polymer melt was initiated using a heated collector at temperatures above 120 °C and required remarkably slow collector speeds below 100 mm min\(^{-1}\). The fiber surface morphology was affected by the collector speed and an increase in β-phase was observed for scaffolds compared to the unprocessed powder. Videography shows vibrations of the P(VDF-co-TrFE) jet previously unseen during MEW, probably due to repeated charge buildup and discharge. Furthermore, piezo-force microscopy measurements demonstrated the electromechanical response of MEW-fabricated fibers. This research therefore achieves the melt electrohydrodynamic processing of fibers with micrometer resolution into defined structures with an important electroactive polymer.},
  language  = {en}
}
@article{BoehmStahlhutWeichholdetal.2022,
  author    = {B{\"o}hm, Christoph and Stahlhut, Philipp and Weichhold, Jan and Hrynevich, Andrei and Teßmar, J{\"o}rg and Dalton, Paul D.},
  title     = {The Multiweek Thermal Stability of Medical-Grade Poly(ε-caprolactone) During Melt Electrowriting},
  series = {Small},
  volume    = {18},
  journal   = {Small},
  number    = {3},
  doi       = {10.1002/smll.202104193},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-257741},
  year      = {2022},
  abstract  = {Melt electrowriting (MEW) is a high-resolution additive manufacturing technology that places unique constraints on the processing of thermally degradable polymers. With a single nozzle, MEW operates at low throughput and in this study, medical-grade poly(ε-caprolactone) (PCL) is heated for 25 d at three different temperatures (75, 85, and 95 °C), collecting daily samples. There is an initial increase in the fiber diameter and decrease in the jet speed over the first 5 d, then the MEW process remains stable for the 75 and 85 °C groups. When the collector speed is fixed to a value at least 10\% above the jet speed, the diameter remains constant for 25 d at 75 °C and only increases with time for 85 and 95 °C. Fiber fusion at increased layer height is observed for 85 and 95 °C, while the surface morphology of single fibers remain similar for all temperatures. The properties of the prints are assessed with no observable changes in the degree of crystallinity or the Young's modulus, while the yield strength decreases in later phases only for 95 °C. After the initial 5-d period, the MEW processing of PCL at 75 °C is extraordinarily stable with overall fiber diameters averaging 13.5 ± 1.0 µm over the entire 25-d period.},
  language  = {en}
}
@article{BakirciFrankGumbeletal.2021,
  author    = {Bakirci, Ezgi and Frank, Andreas and Gumbel, Simon and Otto, Paul F. and F{\"u}rsattel, Eva and Tessmer, Ingrid and Schmidt, Hans-Werner and Dalton, Paul D.},
  title     = {Melt Electrowriting of Amphiphilic Physically Crosslinked Segmented Copolymers},
  series = {Macromolecular Chemistry and Physics},
  volume    = {222},
  journal   = {Macromolecular Chemistry and Physics},
  number    = {22},
  doi       = {10.1002/macp.202100259},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-257572},
  year      = {2021},
  abstract  = {Various (AB)\(_{n}\) and (ABAC)\(_{n}\) segmented copolymers with hydrophilic and hydrophobic segments are processed via melt electrowriting (MEW). Two different (AB)\(_{n}\) segmented copolymers composed of bisurea segments and hydrophobic poly(dimethyl siloxane) (PDMS) or hydrophilic poly(propylene oxide)-poly(ethylene oxide)-poly(propylene oxide) (PPO-PEG-PPO) segments, while the amphiphilic (ABAC)\(_{n}\) segmented copolymers consist of bisurea segments in the combination of hydrophobic PDMS segments and hydrophilic PPO-PEG-PPO segments with different ratios, are explored. All copolymer compositions are processed using the same conditions, including nozzle temperature, applied voltage, and collector distance, while changes in applied pressure and collector speed altered the fiber diameter in the range of 7 and 60 µm. All copolymers showed excellent processability with MEW, well-controlled fiber stacking, and inter-layer bonding. Notably, the surfaces of all four copolymer fibers are very smooth when visualized using scanning electron microscopy. However, the fibers show different roughness demonstrated with atomic force microscopy. The non-cytotoxic copolymers increased L929 fibroblast attachment with increasing PDMS content while the different copolymer compositions result in a spectrum of physical properties.},
  language  = {en}
}