@article{HaiderAhmadYangetal.2021,
  author    = {Haider, Malik Salman and Ahmad, Taufiq and Yang, Mengshi and Hu, Chen and Hahn, Lukas and Stahlhut, Philipp and Groll, J{\"u}rgen and Luxenhofer, Robert},
  title     = {Tuning the thermogelation and rheology of poly(2-oxazoline)/poly(2-oxazine)s based thermosensitive hydrogels for 3D bioprinting},
  series = {Gels},
  volume    = {7},
  journal   = {Gels},
  number    = {3},
  issn      = {2310-2861},
  doi       = {10.3390/gels7030078},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-241781},
  year      = {2021},
  abstract  = {As one kind of "smart" material, thermogelling polymers find applications in biofabrication, drug delivery and regenerative medicine. In this work, we report a thermosensitive poly(2-oxazoline)/poly(2-oxazine) based diblock copolymer comprising thermosensitive/moderately hydrophobic poly(2-N-propyl-2-oxazine) (pPrOzi) and thermosensitive/moderately hydrophilic poly(2-ethyl-2-oxazoline) (pEtOx). Hydrogels were only formed when block length exceeded certain length (≈100 repeat units). The tube inversion and rheological tests showed that the material has then a reversible sol-gel transition above 25 wt.\% concentration. Rheological tests further revealed a gel strength around 3 kPa, high shear thinning property and rapid shear recovery after stress, which are highly desirable properties for extrusion based three-dimensional (3D) (bio) printing. Attributed to the rheology profile, well resolved printability and high stackability (with added laponite) was also possible. (Cryo) scanning electron microscopy exhibited a highly porous, interconnected, 3D network. The sol-state at lower temperatures (in ice bath) facilitated the homogeneous distribution of (fluorescently labelled) human adipose derived stem cells (hADSCs) in the hydrogel matrix. Post-printing live/dead assays revealed that the hADSCs encapsulated within the hydrogel remained viable (≈97\%). This thermoreversible and (bio) printable hydrogel demonstrated promising properties for use in tissue engineering applications.},
  language  = {en}
}
@article{HaiderAhmadGrolletal.2021,
  author    = {Haider, Malik Salman and Ahmad, Taufiq and Groll, J{\"u}rgen and Scherf-Clavel, Oliver and Kroiss, Matthias and Luxenhofer, Robert},
  title     = {The Challenging Pharmacokinetics of Mitotane: An Old Drug in Need of New Packaging},
  series = {European Journal of Drug Metabolism and Pharmacokinetics},
  volume    = {46},
  journal   = {European Journal of Drug Metabolism and Pharmacokinetics},
  number    = {5},
  issn      = {2107-0180},
  doi       = {10.1007/s13318-021-00700-5},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-270476},
  pages     = {575-593},
  year      = {2021},
  abstract  = {Adrenocortical carcinoma (ACC) is a malignant tumor originating from the adrenal gland cortex with a heterogeneous but overall dismal prognosis in advanced stages. For more than 50 years, mitotane has remained a cornerstone for the treatment of ACC as adjuvant and palliative therapy. It has a very poor aqueous solubility of 0.1 mg/l and high partition coefficient in octanol/water (log P) value of 6. The commercially available dosage form is 500 mg tablets (Lysodren®). Even at doses up to 6 g/day (12 tablets in divided doses) for several months, > 50\% patients do not achieve therapeutic plasma concentration > 14 mg/l due to poor water solubility, large volume of distribution and inter/intra-individual variability in bioavailability. This article aims to give a concise update of the clinical challenges associated with the administration of high-dose mitotane oral therapy which encompass the issues of poor bioavailability, difficult-to-predict pharmacokinetics and associated adverse events. Moreover, we present recent efforts to improve mitotane formulations. Their success has been limited, and we therefore propose an injectable mitotane formulation instead of oral administration, which could bypass many of the main issues associated with high-dose oral mitotane therapy. A parenteral administration of mitotane could not only help to alleviate the adverse effects but also circumvent the variable oral absorption, give better control over therapeutic plasma mitotane concentration and potentially shorten the time to achieve therapeutic drug plasma concentrations considerably. Mitotane as tablet form is currently the standard treatment for adrenocortical carcinoma. It has been used for 5 decades but suffers from highly variable responses in patients, subsequent adverse effects and overall lower response rate. This can be fundamentally linked to the exceedingly poor water solubility of mitotane itself. In terms of enhancing water solubility, a few research groups have attempted to develop better formulations of mitotane to overcome the issues associated with tablet dosage form. However, the success rate was limited, and these formulations did not make it into the clinics. In this article, we have comprehensively reviewed the properties of these formulations and discuss the reasons for their limited utility. Furthermore, we discuss a recently developed mitotane nanoformulation that led us to propose a novel approach to mitotane therapy, where intravenous delivery supplements the standard oral administration. With this article, we combine the current state of knowledge as a single piece of information about the various problems associated with the use of mitotane tablets, and herein we postulate the development of a new injectable mitotane formulation, which can potentially circumvent the major problems associated to mitotane's poor water solubility.},
  language  = {en}
}
@article{SeifertGruberGburecketal.2021,
  author    = {Seifert, Annika and Gruber, Julia and Gbureck, Uwe and Groll, J{\"u}rgen},
  title     = {Morphological control of freeze-structured scaffolds by selective temperature and material control in the ice-templating process},
  series = {Advanced Engineering Materials},
  volume    = {24},
  journal   = {Advanced Engineering Materials},
  number    = {3},
  doi       = {10.1002/adem.202100860},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-256330},
  year      = {2021},
  abstract  = {Herein, it is aimed to highlight the importance of the process parameter choice during directional solidification of polymer solutions, as they have a significant influence on the pore structure and orientation. Biopolymer solutions (alginate and chitosan) are directionally frozen, while systematically varying parameters such as the external temperature gradient, the temperature of the overall system, and the temperatures of the cooling surfaces. In addition, the effect of material properties such as molecular weight, solution concentration, or viscosity on the sample morphology is investigated. By selecting appropriate temperature gradients and cooling surface temperatures, aligned pores ranging in size between (50 ± 22) μm and (144 ± 56) μm are observed in the alginate samples, whereas the pore orientation is influenced by altering the external temperature gradient. As this gradient increases, the pores are increasingly oriented perpendicular to the sample surface. This is also observed in the chitosan samples. However, if the overall system is too cold, that is, using temperatures of the lower cooling surface down to -60 °C combined with low temperatures of the upper cooling surface, control over pore orientation is lost. This is also found when viscosity of chitosan solutions is above ≈5 Pas near the freezing point.},
  language  = {en}
}
@article{PinznerKellerMutetal.2021,
  author    = {Pinzner, Florian and Keller, Thorsten and Mut, J{\"u}rgen and Bechold, Julian and Seibel, J{\"u}rgen and Groll, J{\"u}rgen},
  title     = {Polyoxazolines with a vicinally double-bioactivated terminus for biomacromolecular affinity assessment},
  series = {Sensors},
  volume    = {21},
  journal   = {Sensors},
  number    = {9},
  issn      = {1424-8220},
  doi       = {10.3390/s21093153},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-239530},
  year      = {2021},
  abstract  = {Interactions between proteins and carbohydrates with larger biomacromolecules, e.g., lectins, are usually examined using self-assembled monolayers on target gold surfaces as a simplified model measuring setup. However, most of those measuring setups are either limited to a single substrate or do not allow for control over ligand distance and spacing. Here, we develop a synthetic strategy, consisting of a cascade of a thioesterification, native chemical ligation (NCL) and thiol-ene reaction, in order to create three-component polymer conjugates with a defined double bioactivation at the chain end. The target architecture is the vicinal attachment of two biomolecule residues to the α telechelic end point of a polymer and a thioether group at the ω chain end for fixating the conjugate to a gold sensor chip surface. As proof-of-principle studies for affinity measurements, we demonstrate the interaction between covalently bound mannose and ConA in surface acoustic wave (SAW) and surface plasmon resonance (SPR) experiments.},
  language  = {en}
}
@article{HolzmeisterWeichholdGrolletal.2021,
  author    = {Holzmeister, Ib and Weichhold, Jan and Groll, J{\"u}rgen and Zreiqat,, Hala and Gbureck, Uwe},
  title     = {Hydraulic reactivity and cement formation of baghdadite},
  series = {Journal of the American Ceramic Society},
  volume    = {104},
  journal   = {Journal of the American Ceramic Society},
  number    = {7},
  doi       = {10.1111/jace.17727},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-259457},
  pages     = {3554-3561},
  year      = {2021},
  abstract  = {In this study, the hydraulic reactivity and cement formation of baghdadite (Ca\(_{3}\)ZrSi\(_{2}\)O\(_{9}\)) was investigated. The material was synthesized by sintering a mixture of CaCO\(_{3}\), SiO\(_{2}\), and ZrO\(_{2}\) and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.},
  language  = {en}
}
@article{GaritanoTrojaolaSanchoGoetzetal.2021,
  author    = {Garitano-Trojaola, Andoni and Sancho, Ana and G{\"o}tz, Ralph and Eiring, Patrick and Walz, Susanne and Jetani, Hardikkumar and Gil-Pulido, Jesus and Da Via, Matteo Claudio and Teufel, Eva and Rhodes, Nadine and Haertle, Larissa and Arellano-Viera, Estibaliz and Tibes, Raoul and Rosenwald, Andreas and Rasche, Leo and Hudecek, Michael and Sauer, Markus and Groll, J{\"u}rgen and Einsele, Hermann and Kraus, Sabrina and Kort{\"u}m, Martin K.},
  title     = {Actin cytoskeleton deregulation confers midostaurin resistance in FLT3-mutant acute myeloid leukemia},
  series = {Communications Biology},
  volume    = {4},
  journal   = {Communications Biology},
  number    = {1},
  doi       = {10.1038/s42003-021-02215-w},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-260709},
  year      = {2021},
  abstract  = {The presence of FMS-like tyrosine kinase 3-internal tandem duplication (FLT3-ITD) is one of the most frequent mutations in acute myeloid leukemia (AML) and is associated with an unfavorable prognosis. FLT3 inhibitors, such as midostaurin, are used clinically but fail to entirely eradicate FLT3-ITD+AML. This study introduces a new perspective and highlights the impact of RAC1-dependent actin cytoskeleton remodeling on resistance to midostaurin in AML. RAC1 hyperactivation leads resistance via hyperphosphorylation of the positive regulator of actin polymerization N-WASP and antiapoptotic BCL-2. RAC1/N-WASP, through ARP2/3 complex activation, increases the number of actin filaments, cell stiffness and adhesion forces to mesenchymal stromal cells (MSCs) being identified as a biomarker of resistance. Midostaurin resistance can be overcome by a combination of midostaruin, the BCL-2 inhibitor venetoclax and the RAC1 inhibitor Eht1864 in midostaurin-resistant AML cell lines and primary samples, providing the first evidence of a potential new treatment approach to eradicate FLT3-ITD+AML. Garitano-Trojaola et al. used a combination of human acute myeloid leukemia (AML) cell lines and primary samples to show that RAC1-dependent actin cytoskeleton remodeling through BCL2 family plays a key role in resistance to the FLT3 inhibitor, Midostaurin in AML. They showed that by targeting RAC1 and BCL2, Midostaurin resistance was diminished, which potentially paves the way for an innovate treatment approach for FLT3 mutant AML.},
  language  = {en}
}
@article{BlumTaskinShanetal.2021,
  author    = {Blum, Carina and Taskin, Mehmet Berat and Shan, Junwen and Schilling, Tatjana and Schlegelmilch, Katrin and Teßmar, J{\"o}rg and Groll, J{\"u}rgen},
  title     = {Appreciating the First Line of the Human Innate Immune Defense: A Strategy to Model and Alleviate the Neutrophil Elastase-Mediated Attack toward Bioactivated Biomaterials},
  series = {Small},
  volume    = {17},
  journal   = {Small},
  number    = {13},
  doi       = {10.1002/smll.202007551},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-257691},
  year      = {2021},
  abstract  = {Biointerface engineering is a wide-spread strategy to improve the healing process and subsequent tissue integration of biomaterials. Especially the integration of specific peptides is one promising strategy to promote the regenerative capacity of implants and 3D scaffolds. In vivo, these tailored interfaces are, however, first confronted with the innate immune response. Neutrophils are cells with pronounced proteolytic potential and the first recruited immune cells at the implant site; nonetheless, they have so far been underappreciated in the design of biomaterial interfaces. Herein, an in vitro approach is introduced to model and analyze the neutrophil interaction with bioactivated materials at the example of nano-bioinspired electrospun surfaces that reveals the vulnerability of a given biointerface design to the contact with neutrophils. A sacrificial, transient hydrogel coating that demonstrates optimal protection for peptide-modified surfaces and thus alleviates the immediate cleavage by neutrophil elastase is further introduced.},
  language  = {en}
}
@article{NadernezhadRymaGencetal.2021,
  author    = {Nadernezhad, Ali and Ryma, Matthias and Gen{\c{c}}, Hatice and Cicha, Iwona and J{\"u}ngst, Thomasz and Groll, J{\"u}rgen},
  title     = {Melt electrowriting of isomalt for high-resolution templating of embedded microchannels},
  series = {Advanced Material Technologies},
  volume    = {6},
  journal   = {Advanced Material Technologies},
  number    = {8},
  doi       = {10.1002/admt.202100221},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-256401},
  year      = {2021},
  abstract  = {Fabrication of microchannels using 3D printing of sugars as fugitive material is explored in different fields, including microfluidics. However, establishing reproducible methods for the controlled production of sugar structures with sub-100 μm dimensions remains a challenge. This study pioneers the processing of sugars by melt electrowriting (MEW) enabling the fabrication of structures with so far unprecedented resolution from Isomalt. Based on a systematic variation of process parameters, fibers with diameters down to 20 μm can be fabricated. The flexibility in the adjustment of fiber diameter by on-demand alteration of MEW parameters enables generating constructs with perfusable channels within polydimethylsiloxane molds. These channels have a diameter that can be adjusted from 30 to 200 μm in a single design. Taken together, the experiments show that MEW strongly benefits from the thermal and physical stability of Isomalt, providing a robust platform for the fabrication of small-diameter embedded microchannel systems.},
  language  = {en}
}
@article{RymaTylekLiebscheretal.2021,
  author    = {Ryma, Matthias and Tylek, Tina and Liebscher, Julia and Blum, Carina and Fernandez, Robin and B{\"o}hm, Christoph and Kastenm{\"u}ller, Wolfgang and Gasteiger, Georg and Groll, J{\"u}rgen},
  title     = {Translation of collagen ultrastructure to biomaterial fabrication for material-independent but highly efficient topographic immunomodulation},
  series = {Advanced materials},
  volume    = {33},
  journal   = {Advanced materials},
  number    = {33},
  doi       = {10.1002/adma.202101228},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-256381},
  year      = {2021},
  abstract  = {Supplement-free induction of cellular differentiation and polarization solely through the topography of materials is an auspicious strategy but has so far significantly lagged behind the efficiency and intensity of media-supplementation-based protocols. Consistent with the idea that 3D structural motifs in the extracellular matrix possess immunomodulatory capacity as part of the natural healing process, it is found in this study that human-monocyte-derived macrophages show a strong M2a-like prohealing polarization when cultured on type I rat-tail collagen fibers but not on collagen I films. Therefore, it is hypothesized that highly aligned nanofibrils also of synthetic polymers, if packed into larger bundles in 3D topographical biomimetic similarity to native collagen I, would induce a localized macrophage polarization. For the automated fabrication of such bundles in a 3D printing manner, the strategy of "melt electrofibrillation" is pioneered by the integration of flow-directed polymer phase separation into melt electrowriting and subsequent selective dissolution of the matrix polymer postprocessing. This process yields nanofiber bundles with a remarkable structural similarity to native collagen I fibers, particularly for medical-grade poly(ε-caprolactone). These biomimetic fibrillar structures indeed induce a pronounced elongation of human-monocyte-derived macrophages and unprecedentedly trigger their M2-like polarization similar in efficacy as interleukin-4 treatment.},
  language  = {en}
}
@article{SeifertGrollWeichholdetal.2021,
  author    = {Seifert, Annika and Groll, J{\"u}rgen and Weichhold, Jan and Boehm, Anne V. and M{\"u}ller, Frank A. and Gbureck, Uwe},
  title     = {Phase Conversion of Ice-Templated α-Tricalcium Phosphate Scaffolds into Low-Temperature Calcium Phosphates with Anisotropic Open Porosity},
  series = {Advanced Engineering Materials},
  volume    = {23},
  journal   = {Advanced Engineering Materials},
  number    = {5},
  doi       = {10.1002/adem.202001417},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-256311},
  year      = {2021},
  abstract  = {The current study aims to extend the material platform for anisotropically structured calcium phosphates to low-temperature phases such as calcium-deficient hydroxyapatite (CDHA) or the secondary phosphates monetite and brushite. This is achieved by the phase conversion of highly porous α-tricalcium phosphate (α-TCP) scaffolds fabricated by ice-templating into the aforementioned phases by hydrothermal treatment or incubation in phosphoric acid. Prior to these steps, α-TCP scaffolds are either sintered for 8 h at 1400 °C or remain in their original state. Both nonsintered and sintered α-TCP specimens are converted into CDHA by hydrothermal treatment, while a transformation into monetite and brushite is achieved by incubation in phosphoric acid. Hydrothermal treatment for 72 h at 175 °C increases the porosity in nonsintered samples from 85\% to 88\% and from 75\% to 88\% in the sintered ones. An increase in the specific surface area from (1.102 ± 0.005) to (9.17 ± 0.01) m2 g-1 and from (0.190 ± 0.004) to (2.809 ± 0.002) m2 g-1 due to the phase conversion is visible for both the nonsintered and sintered samples. Compressive strength of the nonsintered samples increases significantly from (0.76 ± 0.11) to (5.29 ± 0.94) MPa due to incubation in phosphoric acid.},
  language  = {en}
}