@phdthesis{Oberndorfer2022,
  author    = {Oberndorfer, Florian},
  title     = {Photoluminescence and Raman spectroscopy of doped nanomaterials},
  doi       = {10.25972/OPUS-27854},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-278540},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2022},
  abstract  = {This thesis includes measurements that were recorded by cooperation partners. The EPR spec- trosa mentioned in section 5.2 were recorded by Michael Auth from the Dyakonov Group (Ex- perimental Physics VI, Julius-Maximilians-Universit{\"a}t, W{\"u}rzburg). The TREFISH experiments and transient absorption in section 5.4 spectra were performed by Jašinskas et al. from the V. Gulbi- nas group (Center for Physical Sciences and Technology, Vilnius, Lithuania). This dissertation investigated the interactions of semiconducting single-walled carbon nanotubes (SWNTs) of (6,5) chirality with their environment. Shear-mixing provided high-quality SWNT sus- pensions, which was complemented by various film preparation techniques. These techniques were in turn used to prepare heterostructures with MoS2 and hBN, which were examined with a newly constructed photoluminescence microscope specifically for this purpose. Finally, the change of spectral properties of SWNTs upon doping was investigated in more detail, as well as the behaviour of charge carriers in the tubes themselves. To optimise the SWNT sample preparation techniques that supplied the other experiments, the sample quality of shear-mixed preparations was compared with that of sonicated samples. It was found that the quantum efficiency of sheared suspensions exceeds that of sonicated suspensions as soon as the sonication time exceeds 30 min. The higher PLQY is due to the lower defect concentration in shear-mixed samples. Via transient absorption, a mean lifetime of 17.3 ps and a mean distance between defects of 192.1 nm could be determined. Furthermore, it was found that the increased efficiency of horn sonication is probably not only due to higher shear forces acting on the SWNT bundles but also that the shortening of PFO-BPy strands plays a significant role. Sonication of very long polymer strands significantly increased their effectiveness in shear mixing. While previous approaches could only achieve very low concentrations of SWNTs in suspensions, pre-sonicated polymer yielded results which were comparable with much shorter PFO-BPy batches. Reference experiments also showed that different aggregation processes are relevant during production and further processing. Initial reprocessing of carbon nanotube raw material requires 7 h sonication time and over 24 h shear mixing before no increase in carbon nano concentration is detectable. However, only a few minutes of sonication or shear mixing are required when reprocessing the residue produced during the separation of the slurry. This discrepancy indicates that different aggregates are present, with markedly different aggregation properties. To study low-dimensional heterostructures, a PL microscope was set up with the ability to ob- serve single SWNTs as well as monolayers of other low-dimensional systems. Furthermore, sam- ples were prepared which bring single SWNTs into contact with 2D materials such as h-BN andMoS2 layers and the changes in the photoluminescence spectrum were documented. For h-BN, it was observed whether previous methods for depositing SWNTs could be transferred for photo- luminescence spectroscopy. SWNTs were successfully deposited on monolayers via a modified drip coating, with the limitation that SWNTs aggregate more at the edges of the monolayers. Upon contact of SWNTs with MoS2, significant changes in the emission properties of the mono- layers were observed. The fluorescence, which was mainly dominated by excitons, was shifted towards trion emission. Reference experiments excluded PFO-BPy and toluene as potential causes. Based on the change in the emission behaviour of MoS2, the most plausible explanation is a photoinduced charge transfer leading to delocalised charge carriers on MoS2. In contrast, on SWNTs, the introduction of additional charges would constitute a quenching centre, which would quench their PL emission, making them undetectable in the PL image. In the last chapter, the electronic properties of doped SWNTs and the behaviour of charge carri- ers inside the tubes should be investigated. First, the change in the conductivity of SWNT films with increasing doping levels was docu- mented. The resistance of the films drops drastically at minimum doping. After the initial in- troduction of charges, the resistance drops with increasing dopant concentration according to a double logarithmic curve. The initial drop could be due to a reduction of contact resistances within the SWNT network film, but this could not be further investigated within the scope of this PhD thesis. In cooperation with Andreas Sperlich and Michael Auth, the spin concentration of SWNTs at different doping levels was determined. The obtained concentrations were compared with the carrier concentrations determined from PL and absorption spectra. At low spin densities, good agreement with previous models was found. Furthermore, the presence of isolated spins strongly suggests a localised charge carrier distribution at temperatures around 10 K. When the charge density is increased, the spin density deviates significantly from the charge carrier con- centration. This discrepancy is attributed to the increasing delocalisation of charge carriers at high charge densities and the interactions of neighbouring spins. These results strongly indicate the existence of localised charge carriers in SWNTs at low temperatures. Next, the effect of doping on the Raman spectra of SWNT suspensions was investigated. In gen- eral, doping is expected to reduce the intensity of the Raman bands, i.e. a consequence of the reduced resonance gain due to bleaching of the S2 transition. However, similar to the resistivity measurements, the oscillator strength of the G+ band drops sharply in the first doping steps. It was also found that the G+ band decreases more than would be expected due to loss of reso- nance condition. Furthermore, the G- is bleached faster than the G+ band. All these anomalies suggest that resonance enhancement is not the only relevant effect. Another much faster deac- tivation path for the excitons may be introduced by doping. This would leave less time for the scattering process to occur and reduce the oscillator strength of the Raman bands. In cooperation with Vidmantas et al., the photoinduced charge carrier behaviour of SWNT/PCBM films was investigated. The required films were prepared by drop coating. The SWNT suspen- sions required for this were obtained from sheared SWNT preparations. Using transient absorp- tion and TREFISH, a number of charge transfer effects were identified and their dynamics in- vestigated: the recombination of neutral excitons (< 50 ps), the electron transfer from carbon nanotubes to PCBM molecules (< 1 ps), the decay of charge-transfer excitons (∼200 ps), the recombination of charge carriers between charge-transfer excitons (1 ns to 4 ns) and finally the propagation through the SWNT network (∼20 ns)},
  subject      = {Einwandige Kohlenstoff-Nanor{\"o}hre},
  language  = {en}
}
@phdthesis{Kastner2020,
  author    = {Kastner, Matthias J.},
  title     = {Spectroscopic investigation of molecular adsorption and desorption from individual single-wall carbon nanotubes},
  doi       = {10.25972/OPUS-21175},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-211755},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2020},
  abstract  = {Nanoelectronics is an essential technology for down-scaling beyond the limit of silicon-based electronics. Single-Wall Carbon Nanotubes (SWNT) are semiconducting components that exhibit a large variety of properties that make them usable for sensing, telecommunication, or computational tasks. Due to their high surface to volume ratio, carbon nanotubes are strongly affected by molecular adsorptions, and almost all properties depend on surface adsorption. SWNT with smaller diameters (0.7-0.9nm) show a stronger sensitivity to surface effects. An optimized synthesis route was developed to produce these nanotubes directly. They were produced with a clean surface, high quality, and large lengths of 2 μ m. The results complement previous studies on larger diameters (0.9-1.4nm). They allow performing statistically significant assumptions for a perfect nanotube, which is selected from a subset of nanotubes with good emission intensity, and high mechanical durability. The adsorption of molecules on the surface of carbon nanotubes influences the motion and binding strength of chargeseparated states in this system. To gain insight into the adsorption processes on the surface with a minimum of concurrent overlapping effects, a microscopic setup, and a measurement technique were developed. The system was estimated to exhibit excellent properties like long exciton diffusion lengths (>350nm), and big exciton sizes (8.5(5)nm), which was substantiated by a simulation. We studied the adsorption processes at the surface of Single-Wall Carbon Nanotubes for molecules in the gas phase, solvent molecules, and surfactant molecules. The experiments were all carried out on suspended individualized carbon nanotubes on a silicon wafer substrate. The experiments in the gas-phase showed that the excitonic emission energy and intensity experiences a rapid blue shift during observation. This shift was associated with the spontaneous desorption of large clusters of gaseous molecules caused by laser heat up. The measurement of this desorption was essential for creating a reference to an initially clean surface and allows us to perform a comparison with previous measurements on this topic. Furthermore, the adsorption of hydrogen on the nanotube surface at high temperatures was investigated. It was found that a new emission mode arises slightly red-shifted to the excitonic emission in these systems. The new signal is almost equally strong as the main excitonic peak and was associated with the brightening of dark excitons at sp3-defects through a K-phonon assisted pathway. The finding is useful for the direct synthesis of spintronic devices as these systems are known to act as single-photon emitters. The suspended nanotubes were further studied to estimate the effect of solvent adsorption on the excitonic states during nanotube dispersion for each nanotube individually. A significant quantum yield loss is observable for hexane and acetonitrile, while the emission intensity was found to be the strongest in toluene. The reference to a clean surface allowed us to estimate the exact influence of the dielectric environment of adsorbing solvents on the excitonic emission energy. Solvent adsorption was found to lead to an energy shift that is almost twice as high as suggested in previous studies. The amount of this energy shift, however, was comparably similar for all solvents, which suggests that the influence of the distinct dielectric constant in the outer environment less significantly influences the energy shift than previously thought. An interesting phenomenon was found when using acetonitrile as a solvent, which leads to greatly enhanced emission properties. The emission is more than twice as high as in the same air-suspended nanotubes, which suggests a process that depends on the laser intensity. In this study, it was reasonably explained how an energy down-conversion is possible through the coupling of the excitonic states with solvent vibrations. The strength of this coupling, however, also suggests adsorptions to the inside of the tubular nanotube structure leading to a coupled vibration of linear acetonitrile molecules that are adsorbed to the inner surface. The findings are important for the field of nanofluidics and provide an excellent system for efficient energy down-conversion in the transmission window of biological tissue. Having separated the pure effect of solvent adsorption allowed us to study the undisturbed molecular adsorption of polymers in these systems. The addition of polyfluorene polymer leads to a slow but stepwise intensity increase. The intensity increase is overlapping with a concurrent process that leads to an intensity decrease. Unfortunately, observing the stepwise process has a low spacial resolution of only 100-250nm, which is in the range of the exciton diffusion length in these systems and hinders detailed analysis. The two competing and overlapping processes processes are considered to originate from slow π-stacking and fast side-chain binding. Insights into this process are essential for selecting suitably formed polymers. However, the findings also emphasize the importance of solvent selection during nanotube dispersion since solvent effects were proven to be far more critical on the quantum yield in these systems. These measurements can shed light on the ongoing debate on polymers adsorption during nanotube individualization and allow us to direct the discussion more towards the selection of suitable solvents. This work provides fundamental insights into the adsorption of various molecules on the surface of individually observed suspended Single-Wall Carbon Nanotubes. It allows observing the adsorption of individual molecules below the optical limit in the solid, liquid, and gas phases. Nanotubes are able to act as sensing material for detecting changes in their direct surrounding. These fundamental findings are also crucial for increasing the quantum yield of solvent-dispersed nanotubes. They can provide better light-harvesting systems for microscopy in biological tissue and set the base for a more efficient telecommunication infrastructure with nano-scale spintronics devices and lasing components. The newly discovered solvent alignment in the nanotube surrounding can potentially also be used for supercapacitors that are needed for caching the calculation results in computational devices that use polymer wrapped nanotubes as transistors. Although fundamental, these studies develop a strategy to enlighten this room that is barely only visible at the bottom of the nano-scale.},
  subject      = {Kohlenstoff-Nanor{\"o}hre},
  language  = {en}
}
@phdthesis{Eckstein2019,
  author    = {Eckstein, Klaus},
  title     = {Linear and Nonlinear Spectroscopy of Doped Carbon Nanotubes},
  doi       = {10.25972/OPUS-18897},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-188975},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2019},
  abstract  = {Doping plays a decisive role for the functionality of semiconductor-based (opto-)electronic devices. Hence, the technological utilization of semiconductors necessitates control and a fundamental understanding of the doping process. However, for low-dimensional systems like carbon nanotubes, neither concentration nor distribution of charge carriers is currently well known. The research presented in this thesis investigated the doping of semiconducting carbon nanotubes by spectroscopic methods. Samples of highly purified, intrinsic (6,5) single-wall carbon nanotubes were fabricated using polymer stabilization. Chapter 4 showed that both electro- and redox chemical \$p\$-doping lead to identical bleaching, blueshift, broadening and asymmetry of the S\$_1\$ exciton absorption band. The similar spectral changes induced by both doping schemes suggest that optical spectra can not be used to infer what process was used for doping. Perhaps more importantly, it also indicates that the distribution of charges and the character of the charge transfer states does not depend on the method by which doping was achieved. The detailed analysis of the doping-induced spectral changes in chapter 5 suggests that surplus charges are distributed inhomogeneously. The hypothesis of carrier localization is consistent with the high sensitivity of the S\$_1\$ exciton photoluminescence to additional charge carriers and with the stretched-exponential decay of the exciton population following ultrafast excitation. Both aspects are in good agreement with diffusion-limited contact quenching of excitons at localized charges. Moreover, localized charges act - similar to structural defects - as perturbations to the bandstructure as evidenced by a doping-induced increase of the D-band antiresonance in the mid-infrared spectrum. Quantum mechanical model calculations also suggest that counterions play a crucial role in carrier localization. Counterion adsorption at the nanotube surface is thus believed to induce charge traps of more than 100 meV depth with a carrier localization length on the order of 3 - 4 nm. The doping-induced bleach of interband absorption is accompanied by an absorption increase in the IR region below 600 meV. The observed shift of the IR peak position indicates a continuous transition from localized to rather delocalized charge carriers. This transition is caused by the increase of the overlap of charge carrier wavefunctions at higher charge densities and was modeled by classical Monte-Carlo simulations of intraband absorption. Chapter 6 discussed the spectroscopy of heavily (degenerately) doped nanotubes, which are characterized by a Drude-response of free-carrier intraband absorption in the optical conductivity spectrum. In the NIR spectral region, the S\$_1\$ exciton and X\$+^_1\$ trion absorption is replaced by a nearly 1 eV broad and constant absorption signal, the so-called H-band. The linear and transient absorption spectra of heavily doped nanotubes suggest that the H-band can be attributed to free-carrier interband transitions. Chapter 7 dealt with the quantification of charge carrier densities by linear absorption spectroscopy. A particularly good measure of the carrier density is the S\$_1\$ exciton bleach. For a bleach below about 50 \%, the carrier density is proportional to the bleach. At higher doping levels, deviations from the linear behavior were observed. For doping levels exceeding a fully bleached S\$_1\$ band, the determination of the normalized oscillator strength f\$\text{1st}\$ over the whole first subband region (trion, exciton, free e-h pairs) is recommended for quantification of carrier densities. Based on the nanotube density of states, the carrier density \$n\$ can be estimated using \$n = 0.74\,\text{nm}^{-1} \cdot (1 - f_\text{1st})\$. In the last part of this thesis (chapter 8), the time-resolved spectroelectrochemistry was extended to systems beyond photostable carbon nanotube films. The integration of a flowelectrolysis cell into the transient absorption spectrometer allows the investigation of in-situ electrochemically generated but photounstable molecules due to a continuous exchange of sample volume. First time-resolved experiments were successfully performed using the dye methylene blue and its electrochemically reduced form leucomethylene blue.},
  subject      = {Dotierung},
  language  = {en}
}