@phdthesis{Rauh2013,
  author    = {Rauh, Daniel},
  title     = {Impact of Charge Carrier Density and Trap States on the Open Circuit Voltage and the Polaron Recombination in Organic Solar Cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-90083},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {The focus of this work is studying recombination mechanisms occurring in organic solar cells, as well as their impact on one of their most important parameters — the open circuit voltage Voc. Firstly, the relationship between Voc and the respective charge carrier density n in the active layer under open circuit conditions is analyzed. Therefor, a model after Shockley for the open circuit voltage is used, whose validity is proven with the aid of fits to the measured data. Thereby, it is emphasized that the equation is only valid under special conditions. In the used reference system P3HT:PC61BM the fits are in agreement with the measurement data only in the range of high temperatures (150 - 300 K), where Voc increases linearly with decreasing temperature. At lower temperatures (50 - 150 K), the experiment shows a saturation of Voc. This saturation cannot be explained with the model by the measured falling charge carrier density with decreasing temperatures. In this temperature range Voc is not directly related to the intrinsic properties of the active layer. Voc saturation is due to injection energy barriers at the contacts, which is ascertained by macroscopic simulations. Furthermore, it is observed that Voc in the case of saturation is equivalent to the so-called built-in potential. The difference between the built-in potential and the energy gap corresponds thereby to the sum of the energy barriers at both contacts. With the knowledge of the Voc(n) dependency for not contact limited solar cells, it is possible to investigate the recombination mechanisms of charge carriers in the active layer. For Langevin recombination the recombination rate is Rn2 (recombination order RO = 2), for Shockley-Read-Hall (SRH) Rn1 (RO=1); in various publications RO higher than two is reported with two main explanations. 1: Trap states for charge carriers exist in the respective separated phases, i.e. electrons in the acceptor phase and holes in the donor phase, which leads to a delayed recombination of the charge carriers at the interface of both phases and finally to an apparent recombination order higher than 2. 2: The enhanced R(n) dependency is attributed to the so called recombination prefactor, which again is dependent from n dependent mobility µ. It is shown that for the system P3HT:PC61BM at room temperature the µ(n) dependency does nearly completely explain the higher RO but not at lower temperatures which in this case supports the first explanation. In the material system PTB7:PC71BM the increased RO cannot be explained by the µ(n) dependency even at room temperature. To support the importance of trap states in combination with a phase separation for the explanation of the enhanced RO, additional trap states were incorporated in the solar cells to investigate their influence on the recombination mechanisms. To achieve this, P3HT:PC61BM solar cells were exposed to synthetic air (in the dark and under illumination) or TCNQ was added in small concentrations to the active layer which act as electron traps. For the oxygen degraded solar cell the recombination order is determined by a combination of open Voc-transients and Voc(n) measurements. Thereby, a continuous increase of the recombination order from 2.4 to more than 5 is observed with higher degradation times. By the evaluation of the ideality factor it can be shown that the impact of SRH recombination is increasing with higher trap concentration in relation to Langevin recombination. A similar picture is revealed for solar cells with TCNQ as extrinsic trap states. Finally, a phenomenon called s-shaped IV-curves is investigated, which can sometimes occur for solar cells under illumination. As course of this a reduced surface recombination velocity can be found. Experimentally, the solar cells were fabricated using a special plasma treatment of the ITO contact. The measured IV-curves of such solar cells are reproduced by macroscopic simulations, where the surface recombination velocity is reduced. Hereby, it has to be distinguished between the surface recombination of majority and minority charge carriers at the respective contacts. The theory can be experimentally confirmed by illumination level dependent IV-curves as well as short circuit current density and open circuit voltage transients.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Mingebach2012,
  author    = {Mingebach, Markus Harald},
  title     = {Photocurrent in Organic Solar Cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-73569},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2012},
  abstract  = {A quite new approach to low-cost mass production of flexible solar cells are organic photovoltaics. Even though the device efficiencies increased rapidly during the last years, further imporvements are essential for a successful market launch. One important factor influencing the device efficiency is the photocurrent of a solar cell, which is defined as the difference between the current under illumination and in the dark. In case of organic bulk heterojunction (BHJ) solar cells it is — in contrast to inorganic devices — dependent on the applied bias voltage. The voltage dependence results in a reduced fill factor and thus an even more pronounced influence of the photocurrent on the device efficiency. It is therefore crucial to understand the underlying processes determining the photocurrent in order to be able to further improve the solar cell performance. In a first step the photocurrent of P3HT:PC61BM devices was investigated by a pulsed measurement technique in order to prevent disturbing influences due to device heating under continous illumination. The resulting photocurrent was hyperbolic tangent like and featured a point symmetry, whose origin and meaning were discussed. In addition, the photocurrent was described by a combined model of Braun-Onsager and Sokel-Hughes theory for field dependent polaron pair dissociation and charge extraction, respectively. After this macroscopic view on the photocurrent, the focus of this work moves to the more basic processes determining the photocurrent: charge photogeneration and recombination. In a comparative study the field-dependence of these was investigated by time-delayed collection field (TDCF) measurements for two well-known reference systems, namely P3HT:PC61BM and MDMO-PPV:PC61BM. It was possible to identify two different dominating scenarios for the generation of free charge carriers. The first one — via a thermalized charge transfer state (CTS) — is clearly influenced by geminate recombination and therefore less efficient. In the second scenario, the free charge carriers are either generated directly or via an excited, "hot" CTS. In addition, clear differences in the nongeminate recombination dynamics of both material systems were found. Similar studies were also be presented with two modern low bandgap polymers which only differ by the bridging atom in the cyclopentadithiophene (PCPDTBT:PC71BM vs. Si-PCPDTBT:PC71BM). Such small changes in the chemical structure were already sufficient to affect the charge photogeneration as well as the morphology of the blend. These findings were set into relation to current-voltage characteristics in order to discuss the origin of the clear differences in the solar cell performance of both materials. Another crucial parameter limiting the solar cell efficiency is the builtin potential of a device. Within the range of semiconducting pn-junctions, Mott-Schottky analysis is an established method to determine the built-in potential. As it was originally derived for abrupt pn-junctions, its validity for organic BHJ solar cells — a bipolar, effective medium — was discussed. Experimental findings as well as the contradictions to Mott-Schottky theory indicated, that a direct transfer of this method to organic photovoltaics is not appropriate. Finally, the results obtained in the framework of the MOPS-project (Massengedruckte Organische Papier-Solarzellen) will be presented, in which the first completely roll-to-roll printed paper solar cells were realized.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@article{KiermaschFischerGilEscrigetal.2021,
  author    = {Kiermasch, David and Fischer, Mathias and Gil-Escrig, Lid{\´o}n and Baumann, Andreas and Bolink, Henk J. and Dyakonov, Vladimir and Tvingstedt, Kristofer},
  title     = {Reduced Recombination Losses in Evaporated Perovskite Solar Cells by Postfabrication Treatment},
  series = {Solar RRL},
  volume    = {5},
  journal   = {Solar RRL},
  number    = {11},
  doi       = {10.1002/solr.202100400},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-258003},
  year      = {2021},
  abstract  = {The photovoltaic perovskite research community has now developed a large set of tools and techniques to improve the power conversion efficiency (PCE). One such arcane trick is to allow the finished devices to dwell in time, and the PCE often improves. Herein, a mild postannealing procedure is implemented on coevaporated perovskite solar cells confirming a substantial PCE improvement, mainly attributed to an increased open-circuit voltage (V\(_{OC}\)). From a V\(_{OC}\) of around 1.11 V directly after preparation, the voltage improves to more than 1.18 V by temporal and thermal annealing. To clarify the origin of this annealing effect, an in-depth device experimental and simulation characterization is conducted. A simultaneous reduction of the dark saturation current, the ideality factor (n\(_{id}\)), and the leakage current is revealed, signifying a substantial impact of the postannealing procedure on recombination losses. To investigate the carrier dynamics in more detail, a set of transient optoelectrical methods is first evaluated, ascertaining that the bulk carrier lifetime is increased with device annealing. Second, a drift-diffusion simulation is used, confirming that the beneficial effect of the annealing has its origin in effective bulk trap passivation that accordingly leads to a reduction of Shockley-Read-Hall recombination rates.},
  language  = {en}
}
@phdthesis{Foertig2013,
  author    = {F{\"o}rtig, Alexander},
  title     = {Recombination Dynamics in Organic Solar Cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-83895},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {Neben herk{\"o}mmlichen, konventionellen anorganischen Solarzellen — haupts{\"a}chlich auf Silizium basierend — ist die Organische Photovoltaik (OPV) auf dem besten Wege in naher Zukunft eine kosteng{\"u}nstige, umweltfreundliche, komplement{\"a}re Technolgie darzustellen. Die Produktionskosten, die Lebenszeit der Solarzellen sowie deren Wirkungsgrad m{\"u}ssen dabei weiter optimiert werden, um einen Markteintritt der OPV zu erm{\"o}glichen. Die vorliegende Arbeit befasst sich mit der Effizienz organischer Solarzellen und deren Limitierung durch die Rekombination von Ladungstr{\"a}gern. Um funktionsf{\"a}hige Zellen zu untersuchen, werden zeitaufgel{\"o}ste Experimente wie die Messung der transienten Photospannung (TPV), des transienten Photostroms (TPC), die Ladungsextraktion (CE) sowie die time delayed collection field (TDCF) Methode angewandt. Untersucht werden sowohl fl{\"u}ssig prozessierte als auch aufgedampfte Proben, unterschiedliche Materialzusammensetzungen und verschiedene Probengeometrien. Das Standardmaterialsystem der OPV, P3HT:PC61BM, wird bei verschiedenen emperaturen und Beleuchtungsst{\"a}rken auf die Lebenszeit und Dichte der photogenerierten Ladungstr{\"a}ger {\"u}berpr{\"u}ft. F{\"u}r den Fall spannungsunabh{\"a}ngiger Generation von Ladungstr{\"a}gern zeigt sich die Anwendbarkeit der Shockley-Gleichung auf organische Solarzellen. Des Weiteren wird ein konsistentes Modell erl{\"a}utert, welches den Idealtit{\"a}tsfaktor direkt mit der Rekombination von freien mit gefangenen, exponentiell verteilten Ladungstr{\"a}gern verkn{\"u}pft. Ein Ansatz, bekannt unter der Bezeichung j=V Rekonstruktion, erm{\"o}glicht es, den leistungslimitierenden Verlustmechanismus in unbehandelten und thermisch geheizten P3HT:PC61BM Solarzellen zu identifizieren. Dieses Verf ahren, welches TPV, CE und TDCF Messungen beinhaltet, wird auf Proben basierend auf dem neuartigen, low-band gap Polymer PTB7 in Verbindung mit dem Fulleren PC71BM ausgeweitet. W{\"a}hrend in der Zelle hergestellt aus reinem Chlorbenzol betr{\"a}chtliche geminale wie nichtgeminale Verluste zu beobachten sind, erleichtert die Zugabe eines L{\"o}sungsmittelzusatzes die Polaronenpaartrennung, was zu einer starken Reduktion geminaler Verluste f{\"u}hrt. In einer Kooperation mit dem IMEC Institut in Leuven, werden abschließend die beiden bedeutensten Probenarchitekturen organischer Solarzellen, die planare und die Misch{\"u}bergang Struktur, jeweils basierend auf CuPC und C60, bez{\"u}glich nichtgeminaler Rekombination und Ladungstr{\"a}gerverteilung miteinander verglichen. Neben den beiden experimentellen Techniken um TPV und CE werden makroskopische Simulationen herangezogen, um den Ursprung unterschiedlichen Voc vs. Lichtintensit{\"a}t-Verhaltens zu erkl{\"a}ren.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Baumann2011,
  author    = {Baumann, Andreas},
  title     = {Charge Transport and Recombination Dynamics in Organic Bulk Heterojunction Solar Cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-64915},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2011},
  abstract  = {The charge transport in disordered organic bulk heterojunction (BHJ) solar cells is a crucial process affecting the power conversion efficiency (PCE) of the solar cell. With the need of synthesizing new materials for improving the power conversion efficiency of those cells it is important to study not only the photophysical but also the electrical properties of the new material classes. Thereby, the experimental techniques need to be applicable to operating solar cells. In this work, the conventional methods of transient photoconductivity (also known as "Time-of-Flight" (TOF)), as well as the transient charge extraction technique of "Charge Carrier Extraction by Linearly Increasing Voltage" (CELIV) are performed on different organic blend compositions. Especially with the latter it is feasible to study the dynamics, i.e. charge transport and charge carrier recombination, in bulk heterojunction (BHJ) solar cells with active layer thicknesses of 100-200 nm. For a well performing organic BHJ solar cells the morphology is the most crucial parameter finding a trade-off between an efficient photogeneration of charge carriers and the transport of the latter to the electrodes. Besides the morphology, the nature of energetic disorder of the active material blend and its influence on the dynamics are discussed extensively in this work. Thereby, the material system of poly(3-hexylthiophene-2,5-diyl) (P3HT) and [6,6]-phenyl-C61 butyric acid methyl ester (PC61BM) serves mainly as a reference material system. New promising donor or acceptor materials and their potential for application in organic photovoltaics are studied in view of charge dynamics and compared with the reference system. With the need for commercialization of organic solar cells the question of the impact of environmental conditions on the PCE of the solar cells raises. In this work, organic BHJ solar cells exposed to synthetic air for finite duration are studied in view of the charge carrier transport and recombination dynamics. Finally, within the framework of this work the technique of photo-CELIV is improved. With the modified technique it is now feasible to study the mobility and lifetime of charge carriers in organic solar cells under operating conditions.},
  subject      = {Photovoltaik},
  language  = {en}
}