@phdthesis{Schmidt2008,
  author    = {Schmidt, R{\"u}diger},
  title     = {Perylene Bisimide and Acene Derivatives as Organic Semiconductors in OTFTs},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-29314},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2008},
  abstract  = {This thesis deals with the synthesis of improved organic semiconductors, the detailed investigation of the molecular properties and the solid state arrangements revealed by single crystal X-ray diffraction and finally the development of structureperformance dependencies by measuring of the charge carrier mobilities of the derivatives in thin film transistors. The two main-goals of this thesis were achieved. Well soluble acene derivatives for spin-coated TFTs were obtained, showing charge carrier mobilities in the range of polymer p-type materials. Novel core-fluorinated perylene bisimide dyes were synthesized particularly and the use of electron deficient substituents lead to PBIs with outstanding air-stable mobilities in thin film transistors prepared by vacuum deposition techniques. The relationship between performance, air stability and solid state packing was elucidated in detail by single crystal X-ray diffraction analysis.},
  subject      = {D{\"u}nnschichttransistor},
  language  = {en}
}
@phdthesis{Krause2009,
  author    = {Krause, Stefan},
  title     = {Determination of the transport levels in thin films of organic semiconductors},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-40470},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2009},
  abstract  = {The approach of using the combination of Ultraviolet (UPS) and Inverse Photoemission (IPS) to determine the transport levels in thin films of organic semiconductors is the scope of this work. For this matter all influences on the peak position and width in Photoelectron Spectroscopy are discussed with a special focus on organic semiconductors. Many of these influences are shown with experimental results of the investigation of diindenoperylene on Ag(111). These findings are applied to inorganic semiconductors silicon in order to establish the use of UPS and IPS on a well-understood system. Finally, the method is used to determine the transport level of several organic semiconductors (PTCDA, Alq3, CuPc, DIP, PBI-H4) and the corresponding exciton binding energies are calculated by comparison to optical absorption data.},
  subject      = {Organischer Halbleiter},
  language  = {en}
}
@phdthesis{Leufgen2009,
  author    = {Leufgen, Michael},
  title     = {Effects of structure, sub-micrometer scaling, and environmental conditions on pi-conjugated organic semiconductors in OFET devices},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-52801},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2009},
  abstract  = {The thesis investigates the electrical transport properties of different π-conjugated organic semiconductors applied as active semiconducting material in organic field-effect transistor (OFET) devices. Theses organic materials are αω-dihexylquaterthiophene (DH4T), the tetrathiafulvalene (TTF) derivatives dibenzene-tetrathiafulvalene (DB-TTF) and dithiophene-tetrathiafulvalene (DT-TTF), and polytriarylamine (PTAA). The latter material is an amorphous polymer, the three others are small molecule oligomer materials. Different deposition methods were applied and compared. The investigations in the thesis treat the pure characterisation of the above materials with their different properties in OFET devices. Furthermore, the aim was to observe and analyse general rules and effects in OFETs depending on the structure, previous history, and the device scaling. Therefore, different tools and special analysing methods were developed and applied. These are a standard characterisation method for the classification of the used organic semiconductor, temperature dependent electrical characterisation investigating the electrical transport properties, the newly developed in situ measurement method of OFET devices, the downscaling of the OFET devices of channel length below 100 nm, and the lithographical structuring of a PTAA film.},
  subject      = {Organischer Halbleiter},
  language  = {en}
}
@phdthesis{Schafferhans2011,
  author    = {Schafferhans, Julia},
  title     = {Investigation of defect states in organic semiconductors: Towards long term stable materials for organic photovoltaics},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-57669},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2011},
  abstract  = {In this work, the trap states in the conjugated polymer P3HT, often used as electron donor in organic bulk heterojunction solar cells, three commonly used fullerene based electron acceptors and P3HT:PC61BM blends were investigated. Furthermore, the trap states in the blend were compared with these of the pure materials. Concerning the lifetime of organic solar cells the influence of oxygen on P3HT and P3HT:PC61BM blends was studied. The experimental techniques used to investigate the trap states in the organic semiconductors were (fractional) thermally stimulated current (TSC) and current based deep level transient spectroscopy (Q-DLTS). Fractional TSC measurements on P3HT diodes revealed a quasi-continuous trap distribution. The distribution suggested two different traps in P3HT with approximately Gaussian energy distributions and maxima at about 50 meV and 105 meV. Thereby, the former was attributed to the tail states within the regular Gaussian density of states due to the low activation energy. The latter, deeper traps, however, exhibited a strong dependence on oxygen. Exposure of the P3HT diodes to oxygen, ambient air and synthetic (dry) air all revealed an increase of the deeper traps density with exposure time in the same manner. While the lower limit of the trap density in non aged P3HT samples was in the range of (1.0 - 1.2)×10^22 m^-3, it was more than doubled after an exposure of 50 h to air. An increase of the trap density with oxygen exposure time was also seen in the Q-DLTS measurements accompanied with an increase of the temperature dependence of the emission rates, indicating an enhanced formation of deeper traps. Due to the raise in density of the deeper traps, the charge carrier mobility in P3HT significantly decreased, as revealed by photo-CELIV measurements, resulting in a loss in mobility of about two orders of magnitude after 100 h exposure to synthetic air. The increased trap density was attributed to p-doping of P3HT by the transfer of an electron to adsorbed oxygen. This effect was partially reversible by applying vacuum to the sample for several hours or, more significantly, by a thermal treatment of the devices in nitrogen atmosphere. The trap states in the methanofullerenes PC61BM, bisPC61BM and PC71BM were investigated by TSC measurements. PC61BM yielded a broad quasi-continuous trap distribution with the maximum of the distribution at about 75 meV. The comparison of the TSC spectra of the three methanofullerenes exhibited significant differences in the trap states with higher activation energies of the most prominent traps in bisPC61BM and PC71BM compared to PC61BM. This probably originates from the different isomers bisPC61BM and PC71BM consist of. Each of the isomers yields different LUMO energies, where the lower ones can act as traps. The lower limit of the trap density of all of the three investigated fullerene derivatives exhibited values in the order of 10^22 m^-3, with the highest for bisPC61BM and the lowest for PC61BM. By applying fractional TSC measurements on P3HT:PC61BM solar cells, it was shown that the trap distribution in the blend is a superposition of the traps in pure P3HT and PC61BM and additional deeper traps in the range of about 250 meV to 400 meV. The origin of these additional traps, which can not be related to the pure materials, was attributed to a higher disorder in the blend and P3HT/PC61BM interfaces. This conclusion was supported by standard TSC and Q-DLTS measurements performed on pristine and annealed P3HT:PC61BM blends, exhibiting a higher ratio of the deep traps in the pristine samples. The lower limit of the trap density of the investigated annealed solar cells was in the range of (6-8)×10^22 m^-3, which was considerably higher than in the pure materials. The influence of oxygen on P3HT:PC61BM solar cells was investigated by exposure of the devices to synthetic air under specific conditions. Exposure of the solar cells to oxygen in the dark resulted in a strong decrease in the power conversion efficiency of 60 \% within 120 h, which was only caused by a loss in short-circuit current. Simultaneous illumination of the solar cells during oxygen exposure strongly accelerated the degradation, resulting in an efficiency loss of 30 \% within only 3 h. Thereby, short-circuit current, open-circuit voltage and fill factor all decreased in the same manner. TSC measurements revealed an increase of the density of deeper traps for both degradation conditions, which resulted in a decrease of the mobility, as investigated by CELIV measurements. However, these effects were less pronounced than in pure P3HT. Furthermore, an increase of the equilibrium charge carrier density with degradation time was observed, which was attributed to oxygen doping of P3HT. With the aid of macroscopic simulations, it was shown that the doping of the solar cells is the origin of the loss in short-circuit current for both degradation conditions.},
  subject      = {Organischer Halbleiter},
  language  = {en}
}
@phdthesis{Wagenpfahl2013,
  author    = {Wagenpfahl, Alexander Johannes},
  title     = {Numerical simulations on limitations and optimization strategies of organic solar cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-90119},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {Continuously increasing energy prices have considerably influenced the cost of living over the last decades. At the same time increasingly extreme weather conditions, drought-filled summers as well as autumns and winters with heavier rainfall and worsening storms have been reported. These are possibly the harbingers of the expected approaching global climate change. Considering the depletability of fossil energy sources and a rising distrust in nuclear power, investigations into new and innovative renewable energy sources are necessary to prepare for the coming future. In addition to wind, hydro and biomass technologies, electricity generated by the direct conversion of incident sunlight is one of the most promising approaches. Since the syntheses and detailed studies of organic semiconducting polymers and fullerenes were intensified, a new kind of solar cell fabrication became conceivable. In addition to classical vacuum deposition techniques, organic cells were now also able to be processed from a solution, even on flexible substrates like plastic, fabric or paper. An organic solar cell represents a complex electrical device influenced for instance by light interference for charge carrier generation. Also charge carrier recombination and transport mechanisms are important to its performance. In accordance to Coulomb interaction, this results in a specific distribution of the charge carriers and the electric field, which finally yield the measured current-voltage characteristics. Changes of certain parameters result in a complex response in the investigated device due to interactions between the physical processes. Consequently, it is necessary to find a way to generally predict the response of such a device to temperature changes for example. In this work, a numerical, one-dimensional simulation has been developed based on the drift-diffusion equations for electrons, holes and excitons. The generation and recombination rates of the single species are defined according to a detailed balance approach. The Coulomb interaction between the single charge carriers is considered through the Poisson equation. An analytically non-solvable differential equation system is consequently set-up. With numerical approaches, valid solutions describing the macroscopic processes in organic solar cells can be found. An additional optical simulation is used to determine the spatially resolved charge carrier generation rates due to interference. Concepts regarding organic semiconductors and solar cells are introduced in the first part of this work. All chapters are based on previous ones and logically outline the basic physics, device architectures, models of charge carrier generation and recombination as well as the mathematic and numerical approaches to obtain valid simulation results. In the second part, the simulation is used to elaborate issues of current interest in organic solar cell research. This includes a basic understanding of how the open circuit voltage is generated and which processes limit its value. S-shaped current-voltage characteristics are explained assigning finite surface recombination velocities at metal electrodes piling-up local space charges. The power conversion efficiency is identified as a trade-off between charge carrier accumulation and charge extraction. This leads to an optimum of the power conversion efficiency at moderate to high charge carrier mobilities. Differences between recombination rates determined by different interpretations of identical experimental results are assigned to a spatially inhomogeneous recombination, relevant for almost all low mobility semiconductor devices.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Gsaenger2013,
  author    = {Gs{\"a}nger, Marcel},
  title     = {Organic Thin-Film Transistors Based on Dipolar Squaraine Dyes},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-80588},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {In summary, it can be stated that the herein studied set of acceptor-substituted squaraine dyes can be seen as potent candidates for OTFTs. Furthermore, their transistor performance can be easily tuned to obtain hole mobilities up to 0.45 cm2/Vs from solution and 1.3 cm2/Vs from sublimation by choosing adequate deposition techniques. In the end, a probable structural model derived from studies of the thin-film morphology by methods such as optical spectroscopy, AFM and X-ray even facilitated the clarification of the observed charge transport behavior.},
  subject      = {Organische Chemie},
  language  = {en}
}
@phdthesis{Sperlich2013,
  author    = {Sperlich, Andreas},
  title     = {Electron Paramagnetic Resonance Spectroscopy of Conjugated Polymers and Fullerenes for Organic Photovoltaics},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-81244},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {In the presented thesis, the various excited states encountered in conjugated organic semiconductors are investigated with respect to their utilization in organic thin-film solar cells. Most of these states are spin-baring and can therefore be addressed by means of magnetic resonance spectroscopy. The primary singlet excitation (spin 0), as well as positive and negative polaronic charge carriers (spin 1/2) are discussed. Additionally, triplet excitons (spin 1) and charge transfer complexes are examined, focussing on their differing spin-spin interaction strength. For the investigation of these spin-baring states especially methods of electron paramagnetic resonance (EPR) are best suited. Therefore according experimental methods were implemented in the course of this work to study conjugated polymers, fullerenes and their blends with continuous wave as well as time-resolved EPR and optically detected magnetic resonance.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Ruff2013,
  author    = {Ruff, Andreas},
  title     = {On the importance of electronic correlations in potassium-doped organic semiconductors},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-83635},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {The present thesis is concerned with the impact of alkali metal-doping on the electronic structure of semiconducting organic thin films. The organic molecular systems which have been studied are the polycyclic aromatic hydrocarbons picene, pentacene, and coronene. Motivated by reports about exceptional behavior like superconductivity and electronic correlations of their alkali metal-doped compounds, high quality films fabricated from the above named molecules have been studied. The electronic structure of the pristine materials and their doped compounds has been investigated using photoelectron spectroscopy. Core level and valence band studies of undoped films yield excellent photoemission spectra agreeing with or even outperforming previously reported data from the literature. Alkali metal-doping manifests itself in a uniform manner in the electronic structure for all probed samples: Opposed to reports from the literature about metallicity and even superconductivity in alkali metal-doped picene, pentacene, and coronene, all films exhibit insulating nature with an energy gap of the order of one electron-volt. Remarkably, this is independent of the doping concentration and the type of dopant, i.e., potassium, cesium, or sodium. Based on the interplay between narrow bandwidths in organic semiconductors and sufficiently high on-molecule Coulomb repulsion, the non-metallicity is attributed to the strong influence of electronic correlations leading to the formation of a Mott insulator. In the case of picene, this is consolidated by calculations using a combination of density functional theory and dynamical mean-field theory. Beyond the extensive considerations regarding electronic correlations, further intriguing aspects have been observed. The deposition of thin picene films leads to the formation of a non-equilibrium situation between substrate and film surface. Here, the establishment of a homogeneous chemical potential is hampered due to the only weak van der Waals-interactions between the molecular layers in the films. Consequently, spectral weight is measurable above the reference chemical potential in photoemission. Furthermore, it has been found that the acceptance of additional electrons in pentacene is limited. While picene and coronene are able to host up to three extra electrons, in pentacene the limit is already reached for one electron. Finally, further extrinsic effects, coming along with alkali metal-doping, have been scrutinized. The oxidation of potassium atoms induced by the reaction with molecular oxygen in the residual gas of the ultra-high vacuum system turned out to significantly influence the electronic structure of alkali metal-doped picene and coronene. Moreover, also the applied X-ray and UV irradiation caused a certain impact on the photoemission spectra. Surprisingly, both effects did not play a role in the studies of potassium-doped pentacene.},
  subject      = {Organischer Halbleiter},
  language  = {en}
}
@phdthesis{Foertig2013,
  author    = {F{\"o}rtig, Alexander},
  title     = {Recombination Dynamics in Organic Solar Cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-83895},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {Neben herk{\"o}mmlichen, konventionellen anorganischen Solarzellen — haupts{\"a}chlich auf Silizium basierend — ist die Organische Photovoltaik (OPV) auf dem besten Wege in naher Zukunft eine kosteng{\"u}nstige, umweltfreundliche, komplement{\"a}re Technolgie darzustellen. Die Produktionskosten, die Lebenszeit der Solarzellen sowie deren Wirkungsgrad m{\"u}ssen dabei weiter optimiert werden, um einen Markteintritt der OPV zu erm{\"o}glichen. Die vorliegende Arbeit befasst sich mit der Effizienz organischer Solarzellen und deren Limitierung durch die Rekombination von Ladungstr{\"a}gern. Um funktionsf{\"a}hige Zellen zu untersuchen, werden zeitaufgel{\"o}ste Experimente wie die Messung der transienten Photospannung (TPV), des transienten Photostroms (TPC), die Ladungsextraktion (CE) sowie die time delayed collection field (TDCF) Methode angewandt. Untersucht werden sowohl fl{\"u}ssig prozessierte als auch aufgedampfte Proben, unterschiedliche Materialzusammensetzungen und verschiedene Probengeometrien. Das Standardmaterialsystem der OPV, P3HT:PC61BM, wird bei verschiedenen emperaturen und Beleuchtungsst{\"a}rken auf die Lebenszeit und Dichte der photogenerierten Ladungstr{\"a}ger {\"u}berpr{\"u}ft. F{\"u}r den Fall spannungsunabh{\"a}ngiger Generation von Ladungstr{\"a}gern zeigt sich die Anwendbarkeit der Shockley-Gleichung auf organische Solarzellen. Des Weiteren wird ein konsistentes Modell erl{\"a}utert, welches den Idealtit{\"a}tsfaktor direkt mit der Rekombination von freien mit gefangenen, exponentiell verteilten Ladungstr{\"a}gern verkn{\"u}pft. Ein Ansatz, bekannt unter der Bezeichung j=V Rekonstruktion, erm{\"o}glicht es, den leistungslimitierenden Verlustmechanismus in unbehandelten und thermisch geheizten P3HT:PC61BM Solarzellen zu identifizieren. Dieses Verf ahren, welches TPV, CE und TDCF Messungen beinhaltet, wird auf Proben basierend auf dem neuartigen, low-band gap Polymer PTB7 in Verbindung mit dem Fulleren PC71BM ausgeweitet. W{\"a}hrend in der Zelle hergestellt aus reinem Chlorbenzol betr{\"a}chtliche geminale wie nichtgeminale Verluste zu beobachten sind, erleichtert die Zugabe eines L{\"o}sungsmittelzusatzes die Polaronenpaartrennung, was zu einer starken Reduktion geminaler Verluste f{\"u}hrt. In einer Kooperation mit dem IMEC Institut in Leuven, werden abschließend die beiden bedeutensten Probenarchitekturen organischer Solarzellen, die planare und die Misch{\"u}bergang Struktur, jeweils basierend auf CuPC und C60, bez{\"u}glich nichtgeminaler Rekombination und Ladungstr{\"a}gerverteilung miteinander verglichen. Neben den beiden experimentellen Techniken um TPV und CE werden makroskopische Simulationen herangezogen, um den Ursprung unterschiedlichen Voc vs. Lichtintensit{\"a}t-Verhaltens zu erkl{\"a}ren.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Rauh2013,
  author    = {Rauh, Daniel},
  title     = {Impact of Charge Carrier Density and Trap States on the Open Circuit Voltage and the Polaron Recombination in Organic Solar Cells},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-90083},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2013},
  abstract  = {The focus of this work is studying recombination mechanisms occurring in organic solar cells, as well as their impact on one of their most important parameters — the open circuit voltage Voc. Firstly, the relationship between Voc and the respective charge carrier density n in the active layer under open circuit conditions is analyzed. Therefor, a model after Shockley for the open circuit voltage is used, whose validity is proven with the aid of fits to the measured data. Thereby, it is emphasized that the equation is only valid under special conditions. In the used reference system P3HT:PC61BM the fits are in agreement with the measurement data only in the range of high temperatures (150 - 300 K), where Voc increases linearly with decreasing temperature. At lower temperatures (50 - 150 K), the experiment shows a saturation of Voc. This saturation cannot be explained with the model by the measured falling charge carrier density with decreasing temperatures. In this temperature range Voc is not directly related to the intrinsic properties of the active layer. Voc saturation is due to injection energy barriers at the contacts, which is ascertained by macroscopic simulations. Furthermore, it is observed that Voc in the case of saturation is equivalent to the so-called built-in potential. The difference between the built-in potential and the energy gap corresponds thereby to the sum of the energy barriers at both contacts. With the knowledge of the Voc(n) dependency for not contact limited solar cells, it is possible to investigate the recombination mechanisms of charge carriers in the active layer. For Langevin recombination the recombination rate is Rn2 (recombination order RO = 2), for Shockley-Read-Hall (SRH) Rn1 (RO=1); in various publications RO higher than two is reported with two main explanations. 1: Trap states for charge carriers exist in the respective separated phases, i.e. electrons in the acceptor phase and holes in the donor phase, which leads to a delayed recombination of the charge carriers at the interface of both phases and finally to an apparent recombination order higher than 2. 2: The enhanced R(n) dependency is attributed to the so called recombination prefactor, which again is dependent from n dependent mobility µ. It is shown that for the system P3HT:PC61BM at room temperature the µ(n) dependency does nearly completely explain the higher RO but not at lower temperatures which in this case supports the first explanation. In the material system PTB7:PC71BM the increased RO cannot be explained by the µ(n) dependency even at room temperature. To support the importance of trap states in combination with a phase separation for the explanation of the enhanced RO, additional trap states were incorporated in the solar cells to investigate their influence on the recombination mechanisms. To achieve this, P3HT:PC61BM solar cells were exposed to synthetic air (in the dark and under illumination) or TCNQ was added in small concentrations to the active layer which act as electron traps. For the oxygen degraded solar cell the recombination order is determined by a combination of open Voc-transients and Voc(n) measurements. Thereby, a continuous increase of the recombination order from 2.4 to more than 5 is observed with higher degradation times. By the evaluation of the ideality factor it can be shown that the impact of SRH recombination is increasing with higher trap concentration in relation to Langevin recombination. A similar picture is revealed for solar cells with TCNQ as extrinsic trap states. Finally, a phenomenon called s-shaped IV-curves is investigated, which can sometimes occur for solar cells under illumination. As course of this a reduced surface recombination velocity can be found. Experimentally, the solar cells were fabricated using a special plasma treatment of the ITO contact. The measured IV-curves of such solar cells are reproduced by macroscopic simulations, where the surface recombination velocity is reduced. Hereby, it has to be distinguished between the surface recombination of majority and minority charge carriers at the respective contacts. The theory can be experimentally confirmed by illumination level dependent IV-curves as well as short circuit current density and open circuit voltage transients.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Kraus2014,
  author    = {Kraus, Hannes},
  title     = {Optically Detected Magnetic Resonance on Organic and Inorganic Carbon-Based Semiconductors},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-106308},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2014},
  abstract  = {In dieser Arbeit werden drei verschiedene kohlenstoffbasierte Materialsysteme behandelt: (i) Organische Halbleiter und kleine Molek{\"u}le, in Kombination mit Fullerenen f{\"u}r Anwendungen in der organischen Photovoltaik (OPV), (ii) Halbleitende Einzelwand-Kohlenstoffnanor{\"o}hren und (iii) Siliziumkarbid (SiC), dessen Defekte erst seit kurzem als Kandidaten f{\"u}r Quantenapplikationen gehandelt werden. Alle Systeme wurden mit optisch detektierter Magnetresonanzspektroskopie (ODMR) untersucht. Im OPV-Kapitel, die intrinsischen Parameter und Orientierungen von Exzitonen mit hohem Spin wurden f{\"u}r die Materialsysteme P3HT, PTB7 und DIP untersucht. Speziell der Einfluss von Ordnung diesen organischen Systemen wurde diskutiert. Der zweite Teil des Kapitels besch{\"a}ftigt sich mit Triplettgeneration mittels Elektronenr{\"u}cktransfer im leistungsf{\"a}higen Materialsystem PTB7:PC71BM. Das Kohlenstoffnanor{\"o}hren-Kapitel zeigt zuert den ersten zweifelsfreien Nachweis von Triplettexzitonen in halbleitenden (6,5) Einzelwandkohlenstoffnanor{\"o}hren (SWNT), mittels ODMR-Spektroskopie. Ein Modell f{\"u}r die Anregungskinetik, die intrinsischen Parameter des Exzitons und Abh{\"a}ngigkeit von der Orientierung der R{\"o}hren wurden diskutiert. Der letzte Teil der Arbeit gilt Spinzentren in Siliziumkarbid. Nach einer kurzen Einf{\"u}hrung in das Materialsystem wird die Spinmultiplizit{\"a}t f{\"u}r die V2 und V3 Siliziumfehlstellen, sowie eines Frenkelpaars und eines noch nicht zugeordneten Defekts (UD) in 6H SiC, weiterhin f{\"u}r die V2 Fehlstelle und das Frenkelpaar in 4H SiC, durchg{\"a}ngig zu S=3/2 festgestellt. Das spinpolarisierte Bef{\"u}llen der 3/2-Zust{\"a}nde des Grundzustands der Siliziumfehlstellen erlaubt stimulierte Mikrowellenemission. Ausserdem wurde f{\"u}r UD und Frenkelpaar in 6H SiC eine große Temperaturabh{\"a}ngigkeit der Nullfeldparameter festgestellt, w{\"a}hrend die Siliziumfehlstellen temperaturunabh{\"a}ngig sind. Anwendung des UD und Frenkelpaars als Temperatursensor, und der Vakanzen als Vektormagnetometer wurden diskutiert.},
  subject      = {ODMR-Spektroskopie},
  language  = {en}
}
@phdthesis{Gorenflot2014,
  author    = {Gorenflot, Julien Fran{\c{c}}ois},
  title     = {Optical study of the excited states in the semiconducting polymer poly(3-hexylthiophene) for photovoltaic applications},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-116730},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2014},
  abstract  = {In the course of this dissertation, we have presented the interest of using spectroscopic methods to unravel the physics of polymer semiconductors in photovoltaic applications. Applying photoluminescence and photoinduced absorption spectroscopy to the reference system P3HT:PCBM has enabled us to study the major steps of photocurrent generation in organic bulk heterojunctions, from excitons generation to charges extraction and loss mechanisms and thus to improve the understanding of those mechanisms. The exciton binding energy, is the first obstacle to overcome for photocurrent generation in organic solar cell and the reason for the use of two materials, whose heterojunction act as a driving force for charge separation. We developed an original photoluminescence-detected field-induced exciton quenching method to investigate this energy. Absorption and photoluminescence spectra of pure P3HT show that, while both amorphous and crystalline domains participate in absorption, the energy is then transferred to the crystalline domains, from where the photoluminescence is exclusively originating. The field dependence of this photoluminescence showed that an energy of no less than 420 meV is necessary to split excitons into non photon-emitting species. Comparing those results with energy levels obtained by absorption and photoelectron spectroscopies, confirmed that the formation of those species is only a first step toward dissociation into free charges. Indeed, photoemission spectroscopy and the onset of photocurrent upon increasing the photon energy in a pure P3HT solar cell, concomitantly show that the energy level of a pair of free polarons is located 0.7 eV above the one of the exciton. The comprehensive analysis of those results originating from those different method enable us to draw a global picture of the states and energies involved in free polarons generation in pure material. This work has been widely acknowledged by the scientific community, published in Physical Review B in 2010 [1] and presented in national [2] and international [3] conferences. The spectroscopy of excited states is used to detect the presence of wanted species (charges) and potentially unwanted neutral species upon photoexcitation. As such, it offers us the possibility to qualify the efficiency of charge generation and, if any, identify the competing processes and the generation of unwanted species. In the frame of the European Marie Curie Research Network SolarNType,[4] this possibility was used - in combination with morphological, charge transport and devices characterizationsn - to study a number of new donor:acceptor blends. Thanks to those techniques, we were able to not only quantify the potential of those blends, but also to provide the chemist laboratories with a precious and detailed feedback on the strengths and weakness of the molecules, regarding charge generation, transport and extraction. The detailed study of terrylene-3,4:11,12-bis(dicarboximide) as electron acceptor for solar cells application was published in the peer review journal Synthetic Metals and was chosen to illustrate the cover page of the issue [5]. Finally, in the last chapter, we have used time resolved photoinduced absorption to improve the understanding of the charge carrier loss mechanisms in P3HT:PCBM active layers. This comprehension is of prime importance because, the fact that this recombination is far weaker than expected from the Langevin theory, enable polarons to travel further without recombining and thus to build thicker and more efficient devices. A comprehensive analysis of steady-state PIA spectra of pure P3HT, indicates that probing at 980 nm at a temperature between 140 and 250 K enables to monitor specifically polaron densities in both neat P3HT and P3HT:PCBM. Applying this finding to transient absorption enabled us to monitor, for the first time, the bimolecular recombination in pure P3HT, and to discover that - in sharp contrast with the blend - this recombination was in agreement with the Langevin theory. Moreover, it enables us to pinpoint the important role played by the existence of two materials and of energetical traps in the slow recombination and high recombination orders observed in the blend. This work has been published in the Journal of Applied Physics.[6] Those new insights in the photophysics of polymer:fullerene photoactive layers could have a strong impact on the future developement of those materials. Consistent measurements of the binding energy of excitons and intermediate species, would enable to clarify the role played by excess thermal energy in interfacial states dissociation. Better understanding of blends morphology and its influence on solar cells parameters and in particular on recombination could enable to reproduce the conditions of limited recombination on material systems offering some promising performances but with only limited active layer thicknesses. However, due to the number of parameters involved, further experimentation is required, before we can reach a quantitative modeling of bimolecular recombination. [1] Deibel et al., Phys. Rev. B, 81:085202, 2010 [2] Gorenflot et al., Deutsche Physikalische Gesellschaft Fr{\"u}hjahrstagung 2010, CPP20:10, Regensburg, Germany, 2010 [3] Gorenflot et al., International Conference of Synthetic Metals, 7Ax:05, Kyoto, Japan, 2010 [4] Marie-Curie RTN "SolarNTyp" Contract No. MRTN-CT-2006-035533 [5] Gorenflot et al., Synth. Met., 161(23{24):2669-2676, 2012 [6] Gorenflot et al., J. Appl. Phys., 115(14):144502, 2014},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Gieseking2014,
  author    = {Gieseking, Bj{\"o}rn},
  title     = {Excitation Dynamics and Charge Carrier Generation in Organic Semiconductors},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-101625},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2014},
  abstract  = {The transport of optically excited states, called excitons, as well as their conversion into charges define the two major steps allowing for the operation of organic photovoltaic (OPV) devices. Hence, a deep understanding of these processes, the involved mechanisms as well as possible loss channels is crucial for further improving the efficiency of organic solar cells. For studying the aforementioned processes spectroscopic methods like absorption and emission measurements are useful tools. As many of the processes take place on a sub-nanosecond (ns) timescale ultrafast spectroscopic methods are required. Due to this reason two experiments based on a femtosecond laser system were built and employed in this work, namely picosecond (ps) time-resolved photoluminescence (PL) and transient absorption (TA) spectroscopy. By analyzing the PL decay dynamics in the prototypical organic semiconductor rubrene, the feasibility of a new approach for improving the efficiency of organic solar cells by harvesting triplet excitons generated by singlet fission was examined. Singlet fission describes a process where two triplet excitons are generated via a photoexcited singlet exciton precursor state if the energy of the two triplets is comparable with the energy of the singlet. For this purpose the influence of characteristic length scales on the exciton dynamics in different rubrene morphologies exhibiting an increasing degree of confinement was analyzed. The results show that the quenching at interfacial states efficiently suppresses the desired fission process if these states are reached by excitons during migration. Since interfacial states are expected to play a significant role in thin film solar cells and are easily accessible for the migrating excitons, the results have to be considered for triplet-based OPV. While the aforementioned approach is only investigated for model systems so far, the efficiency of disordered organic bulk heterojunction (BHJ) solar cells could be significantly enhanced in the last couple of years by employing new and more complex copolymer donor materials. However, little is known about the photophysics and in particular the excitation dynamics of these systems. By carrying out a systematic optical study on the prominent copolymer PCDTBT and its building blocks we were able to identify the nature of the two characteristic absorption bands and the coupling mechanism between these levels. The latter mechanism is based on an intrachain partial charge transfer between two functional subunits and our time-resolved measurements indicate that this coupling governs the photophysical properties of solar cells based on these copolymers. The efficient coupling of functional subunits can be seen as a key aspect that guarantees for the success of the copolymer approach. Another important issue concerns the optimization of the morphology of BHJ solar cells. It arises from the discrepancy between the exciton diffusion length \mbox{(\$\approx\$ 10 nm)} and the absorption length of solar irradiation (\$\approx\$ 100 nm). Due to this reason, even for devices based on new copolymer materials, processing parameters affecting the morphology like annealing or employing processing additives are of major importance. In our combined optical, electrical and morphological study for solar cells based on the high-efficient copolymer PBDTTT-C we find a direct correlation between additive content and intermixing of the active layer. The observed maximum in device efficiency can be attributed to a morphology guaranteeing for an optimized balance between charge generation and transport. Our results highlight the importance of understanding the influence of processing parameters on the morphology of the BHJ and thus on the efficiency of the device.},
  subject      = {Organische Solarzelle},
  language  = {en}
}
@phdthesis{Vaeth2016,
  author    = {V{\"a}th, Stefan Kilian},
  title     = {On the Role of Spin States in Organic Semiconductor Devices},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-141894},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2016},
  abstract  = {The present work addressed the influence of spins on fundamental processes in organic semiconductors. In most cases, the role of spins in the conversion of sun light into electricity was of particular interest. However, also the reversed process, an electric current creating luminescence, was investigated by means of spin sensitive measurements. In this work, many material systems were probed with a variety of innovative detection techniques based on electron paramagnetic resonance spectroscopy. More precisely, the observable could be customized which resulted in the experimental techniques photoluminescence detected magnetic resonance (PLDMR), electrically detected magnetic resonance (EDMR), and electroluminescence detected magnetic resonance (ELDMR). Besides the commonly used continuous wave EPR spectroscopy, this selection of measurement methods yielded an access to almost all intermediate steps occurring in organic semiconductors during the conversion of light into electricity and vice versa. Special attention was paid to the fact that all results were applicable to realistic working conditions of the investigated devices, i.e. room temperature application and realistic illumination conditions.},
  subject      = {Organischer Halbleiter},
  language  = {en}
}
@phdthesis{Hammer2021,
  author    = {Hammer, Sebastian Tobias},
  title     = {Influence of Crystal Structure on Excited States in Crystalline Organic Semiconductors},
  doi       = {10.25972/OPUS-24401},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-244019},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2021},
  abstract  = {This thesis focused on the influence of the underlying crystal structure and hence, of the mutual molecular orientation, on the excited states in ordered molecular aggregates. For this purpose, two model systems have been investigated. In the prototypical donor-acceptor complex pentacene-perfluoropentacene (PEN-PFP) the optical accessibility of the charge transfer state and the possibility to fabricate highly defined interfaces by means of single crystal templates enabled a deep understanding of the spatial anisotropy of the charge transfer state formation. Transferring the obtained insights to the design of prototypical donor-acceptor devices, the importance of interface control to minimize the occurrence of charge transfer traps and thereby, to improve the device performance, could be demonstrated. The use of zinc phthalocyanine (ZnPc) allowed for the examination of the influence of molecular packing on the excited electronic states without a change in molecular species by virtue of its inherent polymorphism. Combining structural investigations, optical absorption and emission spectroscopy, as well as Franck-Condon modeling of emission spectra revealed the nature of the optical excited state emission in relation to the structural \(\alpha \) and \(\beta \) phase over a wide temperature range from 4 K to 300 K. As a results, the phase transition kinetics of the first order \(\alpha \rightarrow \beta\) phase transition were characterized in depth and applied to the fabrication of prototypical dual luminescent OLEDs.},
  subject      = {Organischer Halbleiter},
  language  = {en}
}
@phdthesis{Gruene2022,
  author    = {Gr{\"u}ne, Jeannine},
  title     = {Spin States and Efficiency-Limiting Pathways in Optoelectronic Materials and Devices},
  doi       = {10.25972/OPUS-29340},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-293405},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2022},
  abstract  = {This thesis addresses the identification and characterization of spin states in optoelectronic materials and devices using multiple spin-sensitive techniques. For this purpose, a systematic study focussing on triplet states as well as associated loss pathways and excited state kinetics was carried out. The research was based on comparing a range of donor:acceptor systems, reaching from organic light emitting diodes (OLEDs) based on thermally activated delayed fluorescence (TADF) to organic photovoltaics (OPV) employing fullerene and multiple non-fullerene acceptors (NFAs). By developing new strategies, e.g., appropriate modeling, new magnetic resonance techniques and experimental frameworks, the influence of spin states in the fundamental processes of organic semiconductors has been investigated. Thereby, the combination of techniques based on the principle of electron paramagnetic resonance (EPR), in particular transient EPR (trEPR) and optically detected magnetic resonance (ODMR), with all-optical methods, such as transient electroluminescence (trEL) and transient absorption (TA), has been employed. As a result, excited spin states, especially molecular and charge transfer (CT) states, were investigated in terms of kinetic behavior and associated pathways, which revealed a significant impact of triplet states on efficiency-limiting processes in both optoelectronic applications.},
  subject      = {Elektronenspinresonanz},
  language  = {en}
}
@phdthesis{Wirsing2023,
  author    = {Wirsing, Sara},
  title     = {Computational Spectroscopic Studies with Focus on Organic Semiconductor Systems},
  doi       = {10.25972/OPUS-28655},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-286552},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2023},
  abstract  = {This work presents excited state investigations on several systems with respect to experimental spectroscopic work. The majority of projects covers the temporal evolution of excitations in thin films of organic semiconductor materials. In the first chapters, thinfilm and interface systems are build from diindeno[1,2,3-cd:1',2',3'-lm]perylene (DIP) and N,N'-bis-(2-ethylhexyl)-dicyanoperylene-3,4:9,10-bis(dicarboximide) (PDIR-CN2) layers, in the third chapter bulk systems consist of 4,4',4"-tris[(3-methylphenyl)phenylamino] triphenylamine (m-MTDATA), 4,7-diphenyl-1,10-phenanthroline (BPhen) and tris-(2,4,6-trimethyl-3-(pyridin-3-yl)phenyl)borane (3TPYMB). These were investigated by aggregate-based calculations. Careful selection of methods and incorporation of geometrical relaxation and environmental effects allows for a precise energetical assignment of excitations. The biggest issue was a proper description of charge-transfer excitations, which was resolved by the application of ionization potential tuning on aggregates. Subsequent characterization of excitations and their interplay condenses the picture. Therefore, we could assign important features of the experimental spectroscopic data and explain differences between systems. The last chapter in this work covers the analysis of single molecule spectroscopy on methylbismut. This poses different challenges for computations, such as multi-reference character of low-lying excitations and an intrinsic need for a relativistic description. We resolved this by combining complete active space self-consistent field based methods with scalarrelativistic density-functional theory. Thus we were able to confidently assign the spectroscopic features and explain underlying processes.},
  subject      = {Theoretische Chemie},
  language  = {en}
}