@phdthesis{Anneser2020, author = {Anneser, Katrin}, title = {Elektrochemische Doppelschichtkondensatoren zur Stabilisierung fluktuierender photovoltaischer Leistung}, doi = {10.25972/OPUS-19933}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-199339}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2020}, abstract = {Der Ausbau der regenerativen Energiequellen f{\"u}hrt vermehrt zu unvorhersehbaren Schwankungen der erzeugten Leistung, da Windkraft und Photovoltaik von nat{\"u}rlichen Bedingungen abh{\"a}ngen. Gerade Kurzzeitfluktuationen im Sekunden- bis Minutenbereich, die bei Solarzellen durch die Verschattung von vor{\"u}berziehenden Wolken zustande kommen, wird bislang wenig Beachtung geschenkt. Kurzzeitspeicher m{\"u}ssen eine hohe Zyklenstabilit{\"a}t aufweisen, um zur Gl{\"a}ttung dieser Leistungsfluktuationen in Frage zu kommen. Im Rahmen der vorliegenden Dissertation wurden elektrochemische Doppelschichtkondensatoren f{\"u}r die Kopplung mit Siliziumsolarzellen und organischen Solarmodulen mit Hilfe von Simulationen und Messungen untersucht. Zus{\"a}tzlich wurden grundlegende Fragestellungen zur Prozessierung und Alterung von Doppelschichtkondensatoren im Hinblick auf ein in der Literatur bereits diskutiertes System betrachtet, das beide Komponenten in einem Bauteil integriert - den sogenannten photocapacitor. Um die Druckbarkeit des gesamten elektrochemischen Doppelschichtkondensators zu erm{\"o}glichen, wurde der konventionell verwendete Fl{\"u}ssigelektrolyt durch einen Polymer-Gel-Elektrolyten auf Basis von Polyvinylalkohol und einer S{\"a}ure ersetzt. Durch eine Verbesserung der Prozessierung konnte ein gr{\"o}ßerer Anteil der spezifischen Fl{\"a}che der por{\"o}sen Kohlenstoffelektroden vom Elektrolyten benetzt und somit zur Speicherung genutzt werden. Die Untersuchungen zeigen, dass mit Polymer-Gel-Elektrolyten {\"a}hnliche Kapazit{\"a}ten erreicht werden wie mit Fl{\"u}ssigelektrolyten. Im Hinblick auf die Anwendung im gekoppelten System muss der elektrochemische Doppelschichtkondensator den gleichen Umweltbedingungen hinsichtlich Temperatur und Luftfeuchte standhalten wie die Solarzelle. Hierzu wurden umfangreiche Alterungstests durchgef{\"u}hrt und festgestellt, dass die Kapazit{\"a}t zwar bei Austrocknung des wasserhaltigen Polymer-Gel-Elektrolyten sinkt, bei einer Wiederbefeuchtung aber auch eine Regeneration des Speichers erfolgt. Zur passenden Auslegung des elektrochemischen Doppelschichtkondensators wurde eine detaillierte Analyse der Leistungsfluktuationen durchgef{\"u}hrt, die mit einem eigens entwickelten MPP-Messger{\"a}t an organischen Solarmodulen gemessen wurden. Anhand der Daten wurde analysiert, welche Energiemengen f{\"u}r welche Zeit im Kurzzeitspeicher zwischengespeichert werden m{\"u}ssen, um eine effiziente Gl{\"a}ttung der ins Netz einzuspeisenden Leistung zu erreichen. Aus der Statistik der Fluktuationen wurde eine Kapazit{\"a}t berechnet, die als Richtwert in die Simulationen einging und dann mit anderen Kapazit{\"a}ten verglichen wurde. Neben einem idealen MPP-Tracking f{\"u}r verschiedene Arten von Solarzellen und Beleuchtungsprofilen konnte die Simulation auch die Kopplung aus Solarzelle und elektrochemischem Doppelschichtkondensator mit zwei verschiedenen Betriebsstrategien nachbilden. Zum einen wurde ein fester Lastwiderstand genutzt, zum anderen eine Zielspannung f{\"u}r den Kurzzeitspeicher und somit auch die Solarzelle vorgegeben und der Lastwiderstand variabel so angepasst, dass die Zielspannung gehalten wird. Beide Betriebsmethoden haben einen Energieverlust gegen{\"u}ber der MPP-getrackten Solarzelle zu verzeichnen, f{\"u}hren aber zu einer Gl{\"a}ttung der Leistung des gekoppelten Systems. Die Simulation konnte f{\"u}r Siliziumsolarzellen mit einem Demonstratorversuch im Labor und f{\"u}r organische Solarzellen unter realen Bedingungen validiert werden. Insgesamt ergibt sich eine vielversprechende Gl{\"a}ttung der Leistungsfluktuationen von Solarzellen durch den Einsatz von elektrochemischen Doppelschichtkondensatoren.}, subject = {Energie}, language = {de} } @phdthesis{Langer2020, author = {Langer, Fabian}, title = {Wachstum und Charakterisierung von 1,0 eV GaInNAs-Halbleitern f{\"u}r die Anwendung in Mehrfachsolarzellen}, doi = {10.25972/OPUS-20088}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-200881}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2020}, abstract = {Im Rahmen dieser Arbeit wurden GaInP/GaAs/GaInNAs 3J-Mehrfachsolarzellen in einem MBE/MOVPE-Hybridprozess hergestellt und untersucht. Der verwendete Hybridprozess, bei dem nur die GaInNAs-Teilsolarzelle mittels MBE hergestellt wird, kombiniert diese beiden Technologien und setzt sie entsprechend ihrer jeweiligen Vorteile ein. Die gezeigten Ergebnisse best{\"a}tigen grunds{\"a}tzlich die Machbarkeit des Hybridprozesses, denn eine Degradation des mittels MBE hergestellten GaInNAs-Materials durch die Atmosph{\"a}re im MOVPE-Reaktor konnte nicht festgestellt werden. Dieses Resultat wurde von im Hybridprozess hergestellten 3J-Mehrfachsolarzellen, die GaInNAs-Teilsolarzellen enthalten, bekr{\"a}ftigt. Die offene Klemmspannung einer gezeigten Solarzelle erreichte bereits 2,59 V (AM1.5d) bzw. 2,48 V (AM0) und liegt damit jeweils {\"u}ber einer als Referenz hergestellten 2J-Mehrfachsolarzelle ohne GaInNAs. Die mittlere interne Quanteneffizienz der enthaltenen GaInNAs-Teilsolarzelle liegt bei 79 \%. Die Berechnungen auf Grundlage dieser Effizienz unter Beleuchtung mit AM1.5d und unter Beleuchtung mit AM0 zeigten, dass nicht die enthaltene GaInNAs-Teilsolarzelle Strom limitierend wirkt, sondern die mittels MOVPE gewachsene GaInP-Teilsolarzelle. Die experimentell bestimmte Kurzschlussstromdichte der hergestellten Mehrfachsolarzelle ist wegen dieser Limitierung etwas geringer als die der 2J-Referenzsolarzelle. Der MOVPE-{\"U}berwachsvorgang bietet zwar noch weiteres Verbesserungspotential, aber es ist naheliegend, dass der Anwachsvorgang auf dem MBE-Material soweit optimiert werden kann, dass die aufgewachsenen GaInP- und GaAs-Schichten frei von Degradation bleiben. Damit bietet der Hybridprozess perspektivisch das Potential g{\"u}nstigere Produktionskosten in der Epitaxie von Mehrfachsolarzellen mit verd{\"u}nnten Nitriden zu erreichen als es ausschließlich mittels MBE m{\"o}glich ist. Im Vorfeld zur Herstellung der 3J-Mehrfachsolarzellen wurden umfassende Optimierungsarbeiten des MBE-Prozesses zur Herstellung der GaInNAs-Teilsolarzelle durchgef{\"u}hrt. So wurde insbesondere festgestellt, dass das As/III-Verh{\"a}ltnis w{\"a}hrend dem Wachstum einen entscheidenden Einfluss auf die elektrisch aktive Dotierung des GaInNAs-Materials besitzt. Die elektrisch aktive Dotierung wiederum beeinflusst sehr stark die Ausdehnung der Raumladungszone in den als p-i-n-Struktur hergestellten GaInNAs-Solarzellen und hat damit einen direkten Einfluss auf deren Stromerzeugung. In der Tendenz zeigte sich eine Zunahme der Stromerzeugung der GaInNAs-Teilsolarzellen bei einer gleichzeitigen Abnahme ihrer offenen Klemmspannung, sobald das As/III-Verh{\"a}ltnis w{\"a}hrend des Wachstums reduziert wurde. Durch eine sehr exakte Kalibration des As/III-Verh{\"a}ltnisses konnte ein bestm{\"o}glicher Kompromiss zwischen offener Klemmspannung und Stromerzeugung gefunden werden. Eine gezeigte GaInNAs-Einfachsolarzelle erreichte eine mittlere interne Quanteneffizienz von 88 \% und eine offene Klemmspannung von 341 mV (AM1.5d) bzw. 351 mV (AM0). Berechnungen auf Grundlage der Quanteneffizienz ergaben, dass diese Solarzelle integriert in eine 3J-Mehrfachsolarzelle unter dem Beleuchtungsspektrum AM1.5g eine Stromdichte von 14,2 mA/cm^2 und unter AM0 von 17,6 mA/cm^2 erzeugen w{\"u}rde. Diese Stromdichten sind so hoch, dass diese GaInNAs-Solarzelle die Stromproduktion der GaInP- und GaAs-Teilsolarzellen in einer g{\"a}ngigen Mehrfachsolarzelle erreicht und keine Ladungstr{\"a}gerverluste auftreten w{\"u}rden. Aufgrund ihrer h{\"o}heren offenen Klemmspannung gegen{\"u}ber einer Ge-Teilsolarzelle bietet diese GaInNAs-Teilsolarzelle das Potential die Effizienz der Mehrfachsolarzelle zu steigern. Messungen der Dotierkonzentration in der GaInNAs-Schicht dieser Solarzelle ergaben extrem geringe Werte im Bereich von 1x10^14 1/cm^3 bis 1x10^15 1/cm^3 (p-Leitung). In Erg{\"a}nzung zu den Optimierungen des As/III-Verh{\"a}ltnisses konnte gezeigt werden, dass sich ein {\"U}bergang von p- zu n-Leitung im GaInNAs mit der Verringerung des As/III-Verh{\"a}ltnisses erzeugen l{\"a}sst. Nahe des {\"U}bergangsbereiches wurden sehr geringe Dotierungen erreicht, die sich durch eine hohe Stromproduktion aufgrund der Ausbildung einer extrem breiten Verarmungszone gezeigt haben. Durch eine reduzierte offene Klemmspannung der bei relativ geringen As/III-Verh{\"a}ltnissen hergestellten Solarzellen mit n-leitendem GaInNAs konnte auf das Vorhandensein von elektrisch aktiven Defekten geschlossen werden. Generell konnten die gemessenen elektrisch aktiven Dotierkonzentrationen im Bereich von {\"u}blicherweise 10^16 1/cm^3 mit hoher Wahrscheinlichkeit auf elektrisch aktive Kristalldefekte im GaInNAs zur{\"u}ckgef{\"u}hrt werden. Eine Kontamination des Materials mit Kohlenstoffatomen in dieser Gr{\"o}ßenordnung wurde ausgeschlossen.}, subject = {Mehrfach-Solarzelle}, language = {de} } @phdthesis{Maier2018, author = {Maier, Patrick}, title = {Memristanz und Memkapazit{\"a}t von Quantenpunkt-Speichertransistoren: Realisierung neuromorpher und arithmetischer Operationen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-164234}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2018}, abstract = {In dieser Arbeit werden Quantenpunkt-Speichertransistoren basierend auf modulationsdotierten GaAs/AlGaAs Heterostrukturen mit vorpositionierten InAs Quantenpunkten vorgestellt, welche in Abh{\"a}ngigkeit der Ladung auf den Quantenpunkten unterschiedliche Widerst{\"a}nde und Kapazit{\"a}ten aufweisen. Diese Ladungsabh{\"a}ngigkeiten f{\"u}hren beim Anlegen von periodischen Spannungen zu charakteristischen, durch den Ursprung gehenden Hysteresen in der Strom-Spannungs- und der Ladungs-Spannungs-Kennlinie. Die ladungsabh{\"a}ngigen Widerst{\"a}nde und Kapazit{\"a}ten erm{\"o}glichen die Realisierung von neuromorphen Operationen durch Nachahmung von synaptischen Funktionalit{\"a}ten und arithmetischen Operationen durch Integration von Spannungs- und Lichtpulsen.}, subject = {Nichtfl{\"u}chtiger Speicher}, language = {de} } @phdthesis{Swimm2017, author = {Swimm, Katrin}, title = {Experimentelle und theoretische Untersuchungen zur gasdruckabh{\"a}ngigen W{\"a}rmeleitf{\"a}higkeit von por{\"o}sen Materialien}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-153887}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2017}, abstract = {Als W{\"a}rmed{\"a}mmstoffe werden {\"u}blicherweise makropor{\"o}se Stoffsysteme wie Sch{\"a}ume, Pul-versch{\"u}ttungen, Faservliese und - wolle eingesetzt. Zus{\"a}tzlich finden mikro- und mesopor{\"o}se D{\"a}mmstoffe wie Aerogele Anwendung. Um effiziente W{\"a}rmed{\"a}mmstoffe entwickeln zu k{\"o}nnen, muss der Gesamtw{\"a}rmetransport in por{\"o}sen Materialien verstanden werden. Die ein-zelnen W{\"a}rmetransport-Mechanismen Festk{\"o}rperw{\"a}rmeleitung, Gasw{\"a}rmeleitung und W{\"a}rme-strahlung k{\"o}nnen zuverl{\"a}ssig analytisch beschrieben werden. Bei manchen por{\"o}sen Materialien liefert jedoch auch eine Wechselwirkung zwischen den verschiedenen W{\"a}rmetransport-Mechanismen, d.h. die Kopplung von Festk{\"o}rper- und Gasw{\"a}rmeleitung, einen hohen Beitrag zur Gesamtw{\"a}rmeleitf{\"a}higkeit. Wie hoch dieser Kopplungseffekt bei einer bestimmten Probe ausf{\"a}llt, kann bisher schwer abgesch{\"a}tzt werden. Um den Kopplungseffekt von Festk{\"o}rper- und Gasw{\"a}rmeleitung besser zu verstehen, sind sowohl experimentelle als auch theoretische Untersuchungen an verschiedenen por{\"o}sen Stoffsystemen erforderlich. Zus{\"a}tzlich kann ein zuverl{\"a}ssiges theoretisches Modell dazu beitragen, die mittlere Porengr{\"o}ße von por{\"o}sen Mate-rialien zerst{\"o}rungsfrei anhand von gasdruckabh{\"a}ngigen W{\"a}rmeleitf{\"a}higkeitsmessungen zu bestimmen. Als Modellsystem f{\"u}r die experimentellen Untersuchungen wurde der hochpor{\"o}se Feststoff Aerogel verwendet, da seine strukturellen Eigenschaften wie Porengr{\"o}ße und Dichte w{\"a}hrend der Synthese gut eingestellt werden k{\"o}nnen. Es wurden Resorcin-Formaldehyd-Aerogele mit mittleren Porengr{\"o}ßen von etwa 600 nm, 1 µm und 8 µm sowie daraus mittels Pyrolyse abge-leitete Kohlenstoff-Aerogele synthetisiert und jeweils hinsichtlich ihrer Struktur und W{\"a}rme-leitf{\"a}higkeiten experimentell charakterisiert. Die Gesamtw{\"a}rmeleitf{\"a}higkeiten dieser Aerogele wurden f{\"u}r verschiedene Gasatmosph{\"a}ren (Kohlenstoffdioxid, Argon, Stickstoff und Helium) in Abh{\"a}ngigkeit vom Gasdruck durch das Hitzdraht-Verfahren bestimmt. Hierf{\"u}r wurde der Messbereich der Hitzdraht-Apparatur des ZAE Bayern mittels einer Druckzelle auf 10 MPa erweitert. Die Messergebnisse zeigen, dass bei allen Aerogel-Proben Festk{\"o}rper- und Gasw{\"a}r-meleitung einen deutlichen Kopplungsbeitrag liefern: Die gemessenen gasdruckabh{\"a}ngigen W{\"a}rmeleitf{\"a}higkeiten sind um Faktor 1,3 bis 3,3 h{\"o}her als die entsprechenden reinen Gas-w{\"a}rmeleitf{\"a}higkeiten. Die jeweilige H{\"o}he h{\"a}ngt sowohl vom verwendeten Gas (Gasw{\"a}rmeleitf{\"a}higkeit) als auch vom Aerogeltyp (Festk{\"o}rperw{\"a}rmeleitf{\"a}higkeit und Festk{\"o}rperstruktur) ab. Ein stark vernetzter Festk{\"o}rper verursacht beispielsweise einen niedrigeren Kopplungsbei-trag als ein weniger stark vernetzter Festk{\"o}rper. Andererseits wurde die gasdruckabh{\"a}ngige W{\"a}rmeleitf{\"a}higkeit von Melaminharzschaum - einem flexiblen, offenporigen und hochpor{\"o}sen Material - in einer evakuierbaren Zwei-Plattenapparatur unter Stickstoff-Atmosph{\"a}re bestimmt. Das Material zeichnet sich dadurch aus, dass die Addition der Einzelw{\"a}rmeleitf{\"a}higkeiten gut erf{\"u}llt ist, d.h. kein Kopplungsef-fekt auftritt. Allerdings konnte gezeigt werden, dass die gestauchte und damit unregelm{\"a}ßige Struktur von Melaminharzschaum die Kopplung von Festk{\"o}rper- und Gasw{\"a}rmeleitung deut-lich beg{\"u}nstigt. Je st{\"a}rker die Melaminharzschaumprobe komprimiert wird, umso st{\"a}rker f{\"a}llt der Kopplungseffekt aus. Bei einer Kompression um 84 \% ist beispielsweise die gemessene gasdruckabh{\"a}ngige W{\"a}rmeleitf{\"a}higkeit bei 0,1 MPa um ca. 17 \% gegen{\"u}ber der effektiven W{\"a}rmeleitf{\"a}higkeit von freiem Stickstoff erh{\"o}ht. Die experimentellen Untersuchungen wurden durch theoretische Betrachtungen erg{\"a}nzt. Zum einen wurde die Kopplung von Festk{\"o}rper- und Gasw{\"a}rmeleitung anhand einer Serienschal-tung der thermischen Widerst{\"a}nde von Festk{\"o}rper- und Gasphase dargestellt, um die Abh{\"a}n-gigkeit von verschiedenen Parametern zu untersuchen. Dadurch konnte gezeigt werden, dass der Kopplungsterm stets von den Verh{\"a}ltnissen aus Festk{\"o}rper- und Gasw{\"a}rmeleitf{\"a}higkeit sowie aus den geometrischen Parametern beider Phasen abh{\"a}ngt. Des Weiteren wurden mit dem Computerprogramm HEAT2 Finite-Differenzen-Simulationen an Modellstrukturen durchgef{\"u}hrt, die f{\"u}r por{\"o}se Stoffsysteme, insbesondere Aerogel, charakteristisch sind (Stege, H{\"a}lse, Windungen und tote Enden). Die simulierten gasdruckabh{\"a}ngigen W{\"a}rmeleitf{\"a}higkeiten zeigen deutlich, dass die Festk{\"o}rperstruktur mit der geringsten Vernetzung, d.h. das tote Ende, am meisten zur Kopplung von Festk{\"o}rper- und Gasw{\"a}rmeleitung beitr{\"a}gt. Dies korre-liert mit den experimentellen Ergebnissen. Dar{\"u}ber hinaus kann man erkennen, dass die Ge-samtw{\"a}rmeleitf{\"a}higkeit eines schlecht vernetzten por{\"o}sen Systems, wo also ein hoher Kopp-lungseffekt (Serienschaltung) auftritt, niemals gr{\"o}ßer wird als die eines gut vernetzten Sys-tems mit gleicher Porosit{\"a}t, wo haupts{\"a}chlich paralleler W{\"a}rmetransport durch beide Phasen stattfindet. Schließlich wurden drei Modelle entwickelt bzw. modifiziert, um die gasdruckabh{\"a}ngige W{\"a}rmeleitf{\"a}higkeit von por{\"o}sen Stoffsystemen theoretisch beschreiben zu k{\"o}nnen. Zun{\"a}chst wurde ein f{\"u}r Kugelsch{\"u}ttungen entwickeltes Modell f{\"u}r Aerogel angepasst, d.h. Kopplung von Festk{\"o}rper- und Gasw{\"a}rmeleitung wurde nur in den L{\"u}cken zwischen zwei benachbarten Partikeln ber{\"u}cksichtigt. Ein Vergleich mit den Messkurven zeigt, dass der ermittelte Kopplungsterm zu gering ausf{\"a}llt. Daher wurde ein bereits existierendes Aerogelmodell mit kubischer Einheitszelle, welches zus{\"a}tzlich Kopplung zwischen den einzelnen Partikelstr{\"a}ngen beinhaltet, verbessert. Auch dieses Modell liefert keine zufriedenstellende {\"U}bereinstimmung mit den Messwerten, denn der Kopplungsbeitrag wird immer noch untersch{\"a}tzt. Das liegt daran, dass die gew{\"a}hlte regelm{\"a}ßige kubische Struktur f{\"u}r Aerogel zu ungenau ist. So geht bei der Berechnung des Kopplungsterms der bereits erw{\"a}hnte hohe Beitrag durch tote Enden (und auch Windungen) verloren. Erfahrungsgem{\"a}ß k{\"o}nnen jedoch alle f{\"u}r Aerogel erhaltenen gasdruckabh{\"a}ngigen Messkurven mit dem sogenannten Skalierungsmodell relativ gut beschrieben werden. Das entspricht dem Knudsen-Modell f{\"u}r reine Gasw{\"a}rmeleitung, welches mit einem konstanten Faktor skaliert wird. Die Anwendung dieses einfachen Modells auf die Messdaten hat gezeigt, dass die Akkommodationskoeffizienten von Helium in Aerogel deut-lich h{\"o}her sind als die Literaturwerte (ca. 0,3 auf Metalloberfl{\"a}chen): In den vermessenen RF- und Kohlenstoff-Aerogelen lassen sich Akkommodationskoeffizienten nahe 1 f{\"u}r Helium ab-leiten. Dar{\"u}ber hinaus ist das Skalierungsmodell gut geeignet, die mittleren Porengr{\"o}ßen por{\"o}ser Materialien zuverl{\"a}ssig aus gasdruckabh{\"a}ngig gemessenen W{\"a}rmeleitf{\"a}higkeitskurven zu bestimmen. Dies stellt somit eine unkomplizierte und zerst{\"o}rungsfreie Charakterisierungsmethode dar.}, subject = {W{\"a}rmeleitf{\"a}higkeit}, language = {de} } @phdthesis{Vaeth2016, author = {V{\"a}th, Stefan Kilian}, title = {On the Role of Spin States in Organic Semiconductor Devices}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-141894}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2016}, abstract = {The present work addressed the influence of spins on fundamental processes in organic semiconductors. In most cases, the role of spins in the conversion of sun light into electricity was of particular interest. However, also the reversed process, an electric current creating luminescence, was investigated by means of spin sensitive measurements. In this work, many material systems were probed with a variety of innovative detection techniques based on electron paramagnetic resonance spectroscopy. More precisely, the observable could be customized which resulted in the experimental techniques photoluminescence detected magnetic resonance (PLDMR), electrically detected magnetic resonance (EDMR), and electroluminescence detected magnetic resonance (ELDMR). Besides the commonly used continuous wave EPR spectroscopy, this selection of measurement methods yielded an access to almost all intermediate steps occurring in organic semiconductors during the conversion of light into electricity and vice versa. Special attention was paid to the fact that all results were applicable to realistic working conditions of the investigated devices, i.e. room temperature application and realistic illumination conditions.}, subject = {Organischer Halbleiter}, language = {en} } @phdthesis{Huppmann2020, author = {Huppmann, Sophia}, title = {Atomlagenabscheidung von Oxidschichten auf Edelmetalloberfl{\"a}chen und deren Haftung}, doi = {10.25972/OPUS-20708}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-207085}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2020}, abstract = {Ziel dieser Arbeit war die Untersuchung einer Passivierungsschicht auf Silber, um es vor Degradation unter Feuchte oder Schadgasen zu sch{\"u}tzen. Dazu wurden Al\(_2\)O\(_3\) und Ta\(_2\)O\(_5\) mittels Atomlagenabscheidung (atomic layer deposition: ALD) auf polykristallinen Silberoberfl{\"a}chen abgeschieden und deren Wachstum und Haftung analysiert. Zum Vergleich wurden die Edelmetalle Gold und Platin herangezogen. Die Beurteilung der Barriereeigenschaften gegen{\"u}ber Schadgas erfolgte mittels einer Ozon-Behandlung in der ALD-Prozesskammer. Es zeigte sich, dass nur ALD-Schichten, die bis zu eine Abscheidetemperatur von unter 140~°C abgeschieden wurden, eine ausreichende Barrierewirkung liefern konnten. Erkl{\"a}rt werden konnte dieses Ph{\"a}nomen durch unterschiedliche Wachtumsregime f{\"u}r unterschiedliche Abscheidetemperaturen zwischen 100 und 300~°C, die in einer temperaturabh{\"a}ngigen Bedeckung der Silberoberfl{\"a}che resultieren. W{\"a}hrend bei niedrigen Temperaturen eine geschlossene Schicht aufw{\"a}chst, findet ALD-Wachstum bei h{\"o}heren Temperaturen, beginnend {\"u}ber 115~°C, nur an Korngrenzen, Stufenkanten und Defekten statt. Es wurden verschiedene Oberfl{\"a}chenbehandlungen untersucht und nur eine Vorbehandlung mit H\(_2\)O bei 100~°C in der ALD-Prozesskammer konnte auch bei h{\"o}heren Temperaturen zu einem geschlossenen Schichtwachstum f{\"u}hren. In-vacuo XPS Untersuchungen der ersten Zyklen des Al\(_2\)O\(_3\)-Wachstums bei 100 und 200~°C auf Silber wurden miteinander und mit einer Silizium Referenzprobe verglichen. Bei beiden Wachstumstemperaturen kam es nicht zur Oxidation von Ag. Ab dem ersten TMA-Puls konnten Al-Verbindungen auf der Oberfl{\"a}che nachgewiesen werden. Es zeigte sich, dass TMA auf der Ag-Oberfl{\"a}che zu Methylaluminium und Methylresten dissoziieren und an Adsorbaten anbinden kann. Zus{\"a}tzlich zeigte sich ein erh{\"o}htes, nicht ges{\"a}ttigtes Wachstumsverhalten bei 200~°C, das {\"u}ber einen Sauerstoffdiffusionsprozess erkl{\"a}rt werden kann. Sauerstoff-Verunreinigungen, die sich in der Silberschicht befinden, konnten {\"u}ber Korngrenzendiffusion an die Oberfl{\"a}che gelangen und dort mit TMA reagieren. Aufgrund von Oberfl{\"a}chendiffusion bei h{\"o}heren Temperaturen gab es eine stabile Adsorption nur an Korngrenzen, Stufenkanten und Defekten. Nur die Si-Oberfl{\"a}che zeigte ein typisches ALD-Wachstum. Auf Pt und Au lag unabh{\"a}ngig von weiteren Vorbehandlungen bei allen Beschichtungstemperaturen ein geschlossenes ALD-Anwachsen vor. Damit eignete sich Au gut um die Barriere-Eigenschaften der ALD-Schicht gegen Feuchtigkeit in Abh{\"a}ngigkeit von der Wachstumstemperatur nachzuweisen. Dies wurde mit einer cyanidischen {\"A}tzl{\"o}sung getestet. W{\"a}hrend f{\"u}r eine Barriere gegen Ozon bereits eine d{\"u}nne geschlossene Schicht, abgeschieden bei 100~°C ausreicht, musste gegen die {\"A}tzl{\"o}sung eine h{\"o}here Beschichtungstemperatur verwendet werden. F{\"u}r die Bewertung der Haftung der Passivierungsschicht wurde neben den {\"u}blichen einfachen Tesatest und Schertest, ein pneumatischer Haftungstest entwickelt und eingesetzt. Daf{\"u}r wurde die Methode des Blistertest angepasst, der urspr{\"u}nglich f{\"u}r die Bestimmung der Haftung organischer Schichten, wie beispielsweise Kleber und Lacke, eingesetzt wurde, sodass er sich f{\"u}r die Untersuchung d{\"u}nner Schichten eignet. Dazu wurde die zu testende Grenzfl{\"a}che mittels eines Si-Tr{\"a}gers mechanisch unterst{\"u}tzt. Hierdurch kann die Deformation der Schicht minimiert werden und es kommt stattdessen zu einem Bruch. Die Delamination der Testschicht wurde durch das Anlegen des hydrostatischen Drucks erreicht, was eine gleichm{\"a}ßige Kraftverteilung gew{\"a}hrleistet. Die Proben ließen sich mittels Standard-D{\"u}nnfilmtechnologie herstellen und k{\"o}nnen damit industriell gut eingesetzt werden. Sowohl der Messaufbau als auch die Probenpr{\"a}paration wurden in dieser Arbeit vorgestellt. Es wurde mittels der beiden Bondmaterialien AuSn und Indium die maximal bestimmbare Adh{\"a}sionsspannung evaluiert und daf{\"u}r Werte von (0,26 \(\pm\) 0,03) \(\cdot 10^9 \) Pa f{\"u}r AuSn und (0,09 \(\pm\) 0,01) \(\cdot 10^9 \) Pa f{\"u}r In bestimmt. Da im In bereits bei sehr niedrigen Dr{\"u}cken ein koh{\"a}sives Versagen auftritt, eignet sich AuSn besser f{\"u}r die Messung anderer Grenzfl{\"a}chen. Damit wurden schließlich die Grenzfl{\"a}chen ALD-Al\(_2\)O\(_3\) und ALD-Ta\(_2\)O\(_5\) auf Ag mit H\(_2\)O-Vorbehandlung sowie ALD-Al\(_2\)O\(_3\) auf Pt untersucht. Es wurden die folgenden Adh{\"a}sionsspannungen erreicht: F{\"u}r ALD-Al\(_2\)O\(_3\) auf Ag: (0,23 \(\pm\) 0,01) \(\cdot 10^9 \) Pa, f{\"u}r ALD-Ta\(_2\)O\(_5\) auf Ag: (0,15 \(\pm\) 0,03) \(\cdot 10^9 \) Pa und f{\"u}r ALD-Al\(_2\)O\(_3\) auf Pt: (0,20 \(\pm\) 0,01) \(\cdot 10^9 \) Pa. Somit wurde best{\"a}tigt, dass mit Hilfe der Vorbehandlung der Ag-Oberfl{\"a}che die ALD-Al\(_2\)O\(_3\)-Schicht nicht nur geschlossen ist, sondern auch ausreichend gut haftet und sich damit hervorragend als Barriere eignet.}, subject = {Aluminiumoxide}, language = {de} } @phdthesis{Kraus2014, author = {Kraus, Hannes}, title = {Optically Detected Magnetic Resonance on Organic and Inorganic Carbon-Based Semiconductors}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-106308}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {In dieser Arbeit werden drei verschiedene kohlenstoffbasierte Materialsysteme behandelt: (i) Organische Halbleiter und kleine Molek{\"u}le, in Kombination mit Fullerenen f{\"u}r Anwendungen in der organischen Photovoltaik (OPV), (ii) Halbleitende Einzelwand-Kohlenstoffnanor{\"o}hren und (iii) Siliziumkarbid (SiC), dessen Defekte erst seit kurzem als Kandidaten f{\"u}r Quantenapplikationen gehandelt werden. Alle Systeme wurden mit optisch detektierter Magnetresonanzspektroskopie (ODMR) untersucht. Im OPV-Kapitel, die intrinsischen Parameter und Orientierungen von Exzitonen mit hohem Spin wurden f{\"u}r die Materialsysteme P3HT, PTB7 und DIP untersucht. Speziell der Einfluss von Ordnung diesen organischen Systemen wurde diskutiert. Der zweite Teil des Kapitels besch{\"a}ftigt sich mit Triplettgeneration mittels Elektronenr{\"u}cktransfer im leistungsf{\"a}higen Materialsystem PTB7:PC71BM. Das Kohlenstoffnanor{\"o}hren-Kapitel zeigt zuert den ersten zweifelsfreien Nachweis von Triplettexzitonen in halbleitenden (6,5) Einzelwandkohlenstoffnanor{\"o}hren (SWNT), mittels ODMR-Spektroskopie. Ein Modell f{\"u}r die Anregungskinetik, die intrinsischen Parameter des Exzitons und Abh{\"a}ngigkeit von der Orientierung der R{\"o}hren wurden diskutiert. Der letzte Teil der Arbeit gilt Spinzentren in Siliziumkarbid. Nach einer kurzen Einf{\"u}hrung in das Materialsystem wird die Spinmultiplizit{\"a}t f{\"u}r die V2 und V3 Siliziumfehlstellen, sowie eines Frenkelpaars und eines noch nicht zugeordneten Defekts (UD) in 6H SiC, weiterhin f{\"u}r die V2 Fehlstelle und das Frenkelpaar in 4H SiC, durchg{\"a}ngig zu S=3/2 festgestellt. Das spinpolarisierte Bef{\"u}llen der 3/2-Zust{\"a}nde des Grundzustands der Siliziumfehlstellen erlaubt stimulierte Mikrowellenemission. Ausserdem wurde f{\"u}r UD und Frenkelpaar in 6H SiC eine große Temperaturabh{\"a}ngigkeit der Nullfeldparameter festgestellt, w{\"a}hrend die Siliziumfehlstellen temperaturunabh{\"a}ngig sind. Anwendung des UD und Frenkelpaars als Temperatursensor, und der Vakanzen als Vektormagnetometer wurden diskutiert.}, subject = {ODMR-Spektroskopie}, language = {en} } @phdthesis{Wolf2015, author = {Wolf, Nadine}, title = {Synthese, Charakterisierung und Modellierung von klassischen Sol-Gel- und Nanopartikel-Funktionsschichten auf der Basis von Zinn-dotiertem Indiumoxid und Aluminium-dotiertem Zinkoxid}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-112416}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Das Ziel dieser Arbeit ist neben der Synthese von Sol-Gel-Funktionsschichten auf der Basis von transparent leitf{\"a}higen Oxiden (transparent conducting oxides, TCOs) die umfassende infrarotoptische und elektrische Charakterisierung sowie Modellierung dieser Schichten. Es wurden sowohl {\"u}ber klassische Sol-Gel-Prozesse als auch {\"u}ber redispergierte Nanopartikel-Sole spektralselektive Funktionsschichten auf Glas- und Polycarbonat-Substraten appliziert, die einen m{\"o}glichst hohen Reflexionsgrad im infraroten Spektralbereich und damit einhergehend einen m{\"o}glichst geringen Gesamtemissionsgrad sowie einen niedrigen elektrischen Fl{\"a}chenwiderstand aufweisen. Zu diesem Zweck wurden dotierte Metalloxide, n{\"a}mlich einerseits Zinn-dotiertes Indiumoxid (tin doped indium oxide, ITO) und andererseits Aluminium-dotiertes Zinkoxid (aluminum doped zinc oxide, AZO)verwendet. Im Rahmen dieser Arbeit wurden vertieft verschiedene Parameter untersucht, die bei der Pr{\"a}paration von niedrigemittierenden ITO- und AZO-Funktionsschichten im Hinblick auf die Optimierung ihrer infrarot-optischen und elektrischen Eigenschaften sowie ihrer Transmission im sichtbaren Spektralbereich von Bedeutung sind. Neben der Sol-Zusammensetzung von klassischen Sol-Gel-ITO-Beschichtungsl{\"o}sungen wurden auch die Beschichtungs- und Ausheizparameter bei der Herstellung von klassischen Sol-Gel-ITO- sowie -AZO-Funktionsschichten charakterisiert und optimiert. Bei den klassischen Sol-Gel- ITO-Funktionsschichten konnte als ein wesentliches Ergebnis der Arbeit der Gesamtemissionsgrad um 0.18 auf 0.17, bei in etwa gleichbleibenden visuellen Transmissionsgraden und elektrischen Fl{\"a}chenwiderst{\"a}nden, reduziert werden, wenn anstelle von (optimierten) Mehrfach-Beschichtungen Einfach-Beschichtungen mit einer schnelleren Ziehgeschwindigkeit anhand des Dip-Coating-Verfahrens hergestellt wurden. Mit einer klassischen Sol-Gel-ITO-Einfach-Beschichtung, die mit einer deutlich erh{\"o}hten Ziehgeschwindigkeit von 600 mm/min gedippt wurde, konnte mit einem Wert von 0.17 der kleinste Gesamtemissionsgrad dieser Arbeit erzielt werden. Die Gesamtemissionsgrade und elektrischen Fl{\"a}chenwiderst{\"a}nde von klassischen Sol-Gel-AZOFunktionsschichten konnten mit dem in dieser Arbeit optimierten Endheizprozess deutlich gesenkt werden. Bei Neunfach-AZO-Beschichtungen konnten der Gesamtemissionsgrad um 0.34 auf 0.50 und der elektrische Fl{\"a}chenwiderstand um knapp 89 \% auf 65 Ω/sq verringert werden. Anhand von Hall-Messungen konnte dar{\"u}ber hinaus nachgewiesen werden, dass mit dem optimierten Endheizprozess, der eine erh{\"o}hte Temperatur w{\"a}hrend der Reduzierung der Schichten aufweist, mit N = 4.3·1019 cm-3 eine etwa doppelt so hohe Ladungstr{\"a}gerdichte und mit µ = 18.7 cm2/Vs eine etwa drei Mal so große Beweglichkeit in den Schichten generiert wurden, im Vergleich zu jenen Schichten, die nach dem alten Endheizprozess ausgeh{\"a}rtet wurden. Das deutet darauf hin, dass bei dem optimierten Heizschema sowohl mehr Sauerstofffehlstellen und damit eine h{\"o}here Ladungstr{\"a}gerdichte als auch Funktionsschichten mit einem h{\"o}heren Kristallisationsgrad und damit einhergehend einer h{\"o}heren Beweglichkeit ausgebildet werden. Ein Großteil der vorliegenden Arbeit behandelt die Optimierung und Charakterisierung von ITO-Nanopartikel-Solen bzw. -Funktionsschichten. Neben den verwendeten Nanopartikeln, dem Dispergierungsprozess, der Beschichtungsart sowie der jeweiligen Beschichtungsparameter und der Nachbehandlung der Funktionsschichten, wurde erstmals in einer ausf{\"u}hrlichen Parameterstudie die Sol-Zusammensetzung im Hinblick auf die Optimierung der infrarot-optischen und elektrischen Eigenschaften der applizierten Funktionsschichten untersucht. Dabei wurde insbesondere der Einfluss der verwendeten Stabilisatoren sowie der verwendeten L{\"o}sungsmittel auf die Schichteigenschaften charakterisiert. Im Rahmen dieser Arbeit wird dargelegt, dass die exakte Zusammensetzung der Nanopartikel-Sole einen große Rolle spielt und die Wahl des verwendeten L{\"o}sungsmittels im Sol einen gr{\"o}ßeren Einfluss auf den Gesamtemissionsgrad und die elektrischen Fl{\"a}chenwiderst{\"a}nde der applizierten Schichten hat als die Wahl des verwendeten Stabilisators. Allerdings wird auch gezeigt, dass keine pauschalen Aussagen dar{\"u}ber getroffen werden k{\"o}nnen, welcher Stabilisator oder welches L{\"o}sungsmittel in den Nanopartikel-Solen zu Funktionsschichten mit kleinen Gesamtemissionsgraden und elektrischen Fl{\"a}chenwiderst{\"a}nden f{\"u}hrt. Stattdessen muss jede einzelne Kombination von verwendetem Stabilisator und L{\"o}sungsmittel empirisch getestet werden, da jede Kombination zu Funktionsschichten mit anderen Eigenschaften f{\"u}hrt. Zudem konnte im Rahmen dieser Arbeit erstmals stabile AZO-Nanopartikel-Sole {\"u}ber verschiedene Rezepte hergestellt werden. Neben der Optimierung und Charakterisierung von ITO- und AZO- klassischen Sol-Gel- sowie Nanopartikel-Solen und -Funktionsschichten wurden auch die infrarot-optischen Eigenschaften dieser Schichten modelliert, um die optischen Konstanten sowie die Schichtdicken zu bestimmen. Dar{\"u}ber hinaus wurden auch kommerziell erh{\"a}ltliche, gesputterte ITO- und AZO-Funktionsschichten modelliert. Die Reflexionsgrade dieser drei Funktionsschicht-Typen wurden einerseits ausschließlich mit dem Drude-Modell anhand eines selbstgeschriebenen Programmes in Sage modelliert, und andererseits mit einem komplexeren Fit-Modell, welches in der kommerziellen Software SCOUT aus dem erweiterten Drude-Modell, einem Kim-Oszillator sowie dem OJL-Modell aufgebaut wurde. In diesem Fit-Modell werden auch die Einfl{\"u}sse der Glas-Substrate auf die Reflexionsgrade der applizierten Funktionsschichten ber{\"u}cksichtigt und es k{\"o}nnen die optischen Konstanten sowie die Dicken der Schichten ermittelt werden. Dar{\"u}ber hinaus wurde im Rahmen dieser Arbeit ein Ellipsometer installiert und geeignete Fit-Modelle entwickelt, anhand derer die Ellipsometer-Messungen ausgewertet und die optischen Konstanten sowie Schichtdicken der pr{\"a}parierten Schichten bestimmt werden k{\"o}nnen.}, subject = {Transparent-leitendes Oxid}, language = {de} } @phdthesis{Spaeth2015, author = {Sp{\"a}th, Florian Leonhard}, title = {Pr{\"a}paration und Charakterisierung einwandiger Kohlenstoffnanorohr-Polyfluoren-Komplexe}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-123874}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Im Fokus dieser Arbeit standen (6,5)-SWNT-PFO-BPy-Komplexe als Vertreter f{\"u}r polyfluorenstabilisierte, einwandige Kohlenstoffnanor{\"o}hren. In einem ersten Projekt wurden pr{\"a}parative Verfahren zur Dispergierung und Abscheidung dieser Proben weiterentwickelt. Es ist gelungen, die Ansatzgr{\"o}ße von 15 mL auf 200 mL hochzuskalieren sowie d{\"u}nne SWNT-Filme {\"u}ber Rotationsbeschichtung herzustellen. Des Weiteren wurde die lichtinduzierte Dynamik in halbleitenden SWNTs von der ps- bis zur µs-Zeitskala untersucht. Hier wurde ein umfassendes Bild zur Singulett- und Triplett-Exzitonendynamik in halbleitenden Kohlenstoffnanor{\"o}hren gezeichnet, welches maßgeblich durch diffusionslimitierte Prozesse gepr{\"a}gt ist. Abschließend wurde eine Methode vorgestellt, mit der sich Informationen zur Struktur von SWNT-Polymer-Komplexen und anderen supramolekularen Systemen gewinnen lassen. Diese basiert auf der Kombination von polarisationswinkelaufgel{\"o}ster Absorptionsspektroskopie an anisotropen Proben und globaler Datenanalyse.}, subject = {Kohlenstoff-Nanor{\"o}hre}, language = {de} } @phdthesis{Fuchs2015, author = {Fuchs, Franziska}, title = {Optical spectroscopy on silicon vacancy defects in silicon carbide}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-124071}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {This work sheds light on different aspects of the silicon vacancy in SiC: (1) Defect creation via irradiation is shown both with electrons and neutrons. Optical properties have been determined: the excitation of the vacancy is most efficient at excitation wavelengths between 720nm and 800nm. The PL decay yields a characteristic excited state lifetime of (6.3±0.6)ns. (2) Defect engineering, meaning the controlled creation of vacancies in SiC with varying neutron fluence. The defect density could be engineered over eight orders of magnitude. On the one hand, in the sample with highest emitter density, the huge PL signal could even be enhanced by factor of five via annealing mechanisms. On the other hand, in the low defect density samples, single defects with photostable room temperature NIR emission were doubtlessly proven. Their lifetime of around 7ns confirmed the value of the transient measurement. (3) Also electrical excitation of the defects has been demonstrated in a SiC LED structure. (4) The investigations revealed for the first time that silicon vacancies can even exist SiC nanocrystals down to sizes of about 60 nm. The defects in the nanocrystals show stable PL emission in the NIR and even magnetic resonance in the 600nm fraction. In conclusion, this work ascertains on the one hand basic properties of the silicon vacancy in silicon carbide. On the other hand, proof-of-principle measurements test the potential for various defect-based applications of the vacancy in SiC, and confirm the feasibility of e.g. electrically driven single photon sources or nanosensing applications in the near future.}, subject = {Siliciumcarbid}, language = {en} } @phdthesis{Weigold2015, author = {Weigold, Lena}, title = {Ermittlung des Zusammenhangs zwischen mechanischer Steifigkeit und W{\"a}rmetransport {\"u}ber das Festk{\"o}rperger{\"u}st bei hochpor{\"o}sen Materialien}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-124806}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Ziel dieser Arbeit ist es, ein verbessertes Verst{\"a}ndnis f{\"u}r den Zusammenhang zwischen mechanischer Steifigkeit und W{\"a}rmetransport {\"u}ber das Festk{\"o}rperger{\"u}st bei hochpor{\"o}sen Materialien zu erlangen. Im Fokus dieser Arbeit steht die Fragestellung, wie mechanische Steifigkeit und W{\"a}rmeleitf{\"a}higkeit bei hochpor{\"o}sen Materialien miteinander zusammenh{\"a}ngen und ob es m{\"o}glich ist, diese beiden Eigenschaften durch geometrische Modifikationen der Mikrostruktur unabh{\"a}ngig voneinander zu ver{\"a}ndern. Die durchgef{\"u}hrten Untersuchungen haben gezeigt, dass ein Großteil der mikrostrukturellen Modifikationen beide Materialeigenschaften beeinflussen und die mechanische Steifigkeit in der Regel eng mit dem W{\"a}rmetransport {\"u}ber das Festk{\"o}rperger{\"u}st verkn{\"u}pft ist. Es konnte jedoch auch nachgewiesen werden, dass die mechanische Steifigkeit bei hochpor{\"o}sen Materialien nicht eindeutig mit dem W{\"a}rmetransport {\"u}ber das Festk{\"o}rperger{\"u}st zusammenh{\"a}ngt und spezifische mikrostrukturelle Modifikationen einen st{\"a}rkeren Einfluss auf die mechanische Steifigkeit besitzen, als auf den W{\"a}rmetransport {\"u}ber das Festk{\"o}rperger{\"u}st. Umgekehrt ist diese Aussage nicht ganz so eindeutig. Die theoretische Betrachtung des Zusammenhangs zeigt, dass in die Berechnung der mechanischen Steifigkeit teils andere geometrische Strukturgr{\"o}ßen einfließen, als in die Berechnung des W{\"a}rmetransports {\"u}ber das Festk{\"o}rperger{\"u}st, so dass die mechanische Steifigkeit unabh{\"a}ngig von der W{\"a}rmeleitf{\"a}higkeit ver{\"a}ndert werden kann. Es zeigt sich jedoch auch, dass die meisten strukturellen Ver{\"a}nderungen beide Eigenschaften beeinflussen und die mechanische Steifigkeit aufgrund der Biegedeformation der Netzwerkelemente systematisch st{\"a}rker auf strukturelle Ver{\"a}nderungen reagiert als die W{\"a}rmeleitf{\"a}higkeit der Struktur, so dass die mechanische Steifigkeit in der Regel quadratisch mit der W{\"a}rmeleitf{\"a}higkeit des Festk{\"o}rperger{\"u}stes skaliert. Mit den Methoden der effective-media-theory lassen sich Grenzen ermitteln, innerhalb derer sich mechanische Steifigkeit und W{\"a}rmeleitf{\"a}higkeit unabh{\"a}ngig voneinander variieren lassen. Im experimentellen Teil der Arbeit wurden Probenserien von Polyurethan-Sch{\"a}umen, Polyurea Aerogelen und organisch / anorganischen Hybrid Aerogelen herangezogen, so dass por{\"o}se Materialien mit geordneten, voll vernetzten Mikrostrukturen, mit statistisch isotropen, teilvernetzen Mikrostrukturen, sowie Mikrostrukturen mit anisotropen Charakter in die Untersuchung einbezogen werden konnten. Als Struktureigenschaften, die die mechanische Steifigkeit ungew{\"o}hnlich stark beeinflussen, konnten die Regelm{\"a}ßigkeit der Struktur und der Kr{\"u}mmungsradius der Netzwerkelemente sicher identifiziert werden. Alle weiteren strukturellen Ver{\"a}nderungen f{\"u}hren zu dem ann{\"a}hernd quadratischen Zusammenhang. In einem dritten Abschnitt dieser Arbeit wird das vereinfachte Phononendiffusionsmodell herangezogen, um den Zusammenhang zwischen mechanischer Steifigkeit und W{\"a}rmetransport {\"u}ber das Festk{\"o}rperger{\"u}st bei Aerogelen grundlagenphysikalisch zu modellieren. Zur Diskussion werden die experimentell ermittelten Eigenschaften der isotropen Polyurea Aerogele herangezogen und eine qualitative Modellierung ihrer Schwingungszustandsdichten durchgef{\"u}hrt. Es konnte gezeigt werden, dass die Kombination aus Probendichte und Schallgeschwindigkeit, mit der sich die mechanische Steifigkeit berechnen l{\"a}sst, unter bestimmten Randbedingungen auch die Energie und Transporteigenschaften der Phononen beschreibt, die den W{\"a}rmetransport {\"u}ber das Festk{\"o}rperger{\"u}st bei Aerogelen bestimmen. Die Ergebnisse dieser Arbeit lassen sich zum Beispiel heranziehen, um die Eigenschaften hochpor{\"o}ser Materialien f{\"u}r eine gegebene Anwendung durch mikrostrukturelle Modifikationen optimal zu gestalten.}, subject = {Por{\"o}ser Stoff}, language = {de} } @phdthesis{Kasper2021, author = {Kasper, Christian Andreas}, title = {Engineering of Highly Coherent Silicon Vacancy Defects in Silicon Carbide}, doi = {10.25972/OPUS-23779}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-237797}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2021}, abstract = {In this work the creation of silicon vacancy spin defects in silicon carbide with predictable properties is demonstrated. Neutron and electron irradiation was used to create silicon vacancy ensembles and proton beam writing to create isolated vacancies at a desired position. The coherence properties of the created silicon vacancies as a function of the emitter density were investigated and a power-law function established. Sample annealing was implemented to increase the coherence properties of existing silicon vacancies. Further, spectral hole burning was used to implement absolute dc-magnetometry.}, subject = {St{\"o}rstelle}, language = {en} } @phdthesis{Zipf2021, author = {Zipf, Matthias}, title = {Ber{\"u}hrungslose Temperaturmessung an Gasen und keramisch beschichteten Oberfl{\"a}chen bei hohen Temperaturen}, doi = {10.25972/OPUS-24024}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-240248}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2021}, abstract = {Station{\"a}re Gasturbinen k{\"o}nnen von großer Bedeutung f{\"u}r die Verlangsamung des Klima-wandels und bei der Bew{\"a}ltigung der Energiewende sein. F{\"u}r die Weiterentwicklung von Gasturbinen zu h{\"o}heren Betriebstemperaturen und damit einhergehend zu h{\"o}heren Wirkungs-graden werden ber{\"u}hrungslose Messverfahren zur Ermittlung der Oberfl{\"a}chentemperatur von Turbinenschaufeln und der Gastemperatur der heißen Verbrennungsgase w{\"a}hrend des Be-triebs ben{\"o}tigt. Im Rahmen dieser Arbeit werden daher Methoden der ber{\"u}hrungslosen Tem-peraturmessung unter Verwendung von Infrarotstrahlung untersucht. Die ber{\"u}hrungslose Messung der Oberfl{\"a}chentemperatur moderner Turbinenschaufeln muss aufgrund derer infrarot-optischer Oberfl{\"a}cheneigenschaften im Wellenl{\"a}ngenbereich des mitt-leren Infrarots durchgef{\"u}hrt werden, in welchem die Turbinenbrenngase starke Absorptions-banden aufweisen. Zur Entwicklung eines ad{\"a}quaten Strahlungsthermometers f{\"u}r diesen Zweck wurden im Rahmen dieser Arbeit daher durch Ermittlung von Transmissionsspektren von Kohlenstoffdioxid und Wasserdampf bei hohen Temperaturen und Dr{\"u}cken in einer ei-gens hierf{\"u}r konstruierten Heißgas-Messzelle zun{\"a}chst Wellenl{\"a}ngenbereiche identifiziert, in welchen die geplanten Messungen m{\"o}glich sind. Anschließend wurde der Prototyp eines ent-sprechend konfigurierten Strahlungsthermometers im Zuge des Testlaufes einer vollskaligen Gasturbine erfolgreich erprobt. Weiterhin wurden im Rahmen dieser Arbeit zwei m{\"o}gliche Verfahren zur ber{\"u}hrungslosen Gastemperaturmessung untersucht. Das erste untersuchte Verfahren setzt ebenfalls auf Strah-lungsthermometrie. Dieses Verfahren sieht vor, aufgrund der Temperaturabh{\"a}ngigkeit des spektralen Transmissionsgrades in den Randbereichen von ges{\"a}ttigten Absorptionsbanden von Gasen aus der in diesen Bereichen transmittierten spektralen Strahldichte auf die Gastempera-tur zu schließen. Im Rahmen dieser Arbeit wurden Voruntersuchungen f{\"u}r dieses Tempera-turmessverfahren durchgef{\"u}hrt. So konnten auf der Grundlage von experimentell ermittelten Transmissionsspektren von Kohlenstoffdioxid bei Dr{\"u}cken zwischen 5 kPa und 600 kPa und Gastemperaturen zwischen Raumtemperatur und 1073 K f{\"u}r das geplante Verfahren nutzbare Wellenl{\"a}ngenintervalle insbesondere im Bereich der Kohlenstoffdioxid-Bande bei 4,26 µm identifiziert werden. Das zweite im Rahmen dieser Arbeit untersuchte Verfahren zur ber{\"u}hrungslosen Gastem-peraturmessung basiert auf der Temperaturabh{\"a}ngigkeit der Wellenl{\"a}ngenposition der Trans-missionsminima der Absorptionsbanden von infrarot-aktiven Gasen. Im Hinblick darauf wur-de dieses Ph{\"a}nomen anhand von experimentell bestimmten hochaufgel{\"o}sten Transmissions-spektren von Kohlenstoffdioxid {\"u}berpr{\"u}ft. Weiterhin wurden m{\"o}gliche Wellenl{\"a}ngenbereiche identifiziert und hinsichtlich ihrer Eignung f{\"u}r das geplante Verfahren charakterisiert. Als am vielversprechendsten erwiesen sich hierbei Teilbanden in den Bereichen um 2,7 µm und um 9,2 µm. Unter Beimischung von Stickstoff mit Partialdr{\"u}cken von bis zu 390 kPa erwies sich zudem auch die Bande bei 4,26 µm als geeignet. Die im Rahmen dieser Arbeit experimentell ermittelten Transmissionsspektren konnten dar-{\"u}ber hinaus schließlich durch Vergleich mit entsprechenden HITRAN-Simulationen verifiziert werden.}, subject = {Pyrometrie}, language = {de} } @phdthesis{Gorenflot2014, author = {Gorenflot, Julien Fran{\c{c}}ois}, title = {Optical study of the excited states in the semiconducting polymer poly(3-hexylthiophene) for photovoltaic applications}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-116730}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {In the course of this dissertation, we have presented the interest of using spectroscopic methods to unravel the physics of polymer semiconductors in photovoltaic applications. Applying photoluminescence and photoinduced absorption spectroscopy to the reference system P3HT:PCBM has enabled us to study the major steps of photocurrent generation in organic bulk heterojunctions, from excitons generation to charges extraction and loss mechanisms and thus to improve the understanding of those mechanisms. The exciton binding energy, is the first obstacle to overcome for photocurrent generation in organic solar cell and the reason for the use of two materials, whose heterojunction act as a driving force for charge separation. We developed an original photoluminescence-detected field-induced exciton quenching method to investigate this energy. Absorption and photoluminescence spectra of pure P3HT show that, while both amorphous and crystalline domains participate in absorption, the energy is then transferred to the crystalline domains, from where the photoluminescence is exclusively originating. The field dependence of this photoluminescence showed that an energy of no less than 420 meV is necessary to split excitons into non photon-emitting species. Comparing those results with energy levels obtained by absorption and photoelectron spectroscopies, confirmed that the formation of those species is only a first step toward dissociation into free charges. Indeed, photoemission spectroscopy and the onset of photocurrent upon increasing the photon energy in a pure P3HT solar cell, concomitantly show that the energy level of a pair of free polarons is located 0.7 eV above the one of the exciton. The comprehensive analysis of those results originating from those different method enable us to draw a global picture of the states and energies involved in free polarons generation in pure material. This work has been widely acknowledged by the scientific community, published in Physical Review B in 2010 [1] and presented in national [2] and international [3] conferences. The spectroscopy of excited states is used to detect the presence of wanted species (charges) and potentially unwanted neutral species upon photoexcitation. As such, it offers us the possibility to qualify the efficiency of charge generation and, if any, identify the competing processes and the generation of unwanted species. In the frame of the European Marie Curie Research Network SolarNType,[4] this possibility was used - in combination with morphological, charge transport and devices characterizationsn - to study a number of new donor:acceptor blends. Thanks to those techniques, we were able to not only quantify the potential of those blends, but also to provide the chemist laboratories with a precious and detailed feedback on the strengths and weakness of the molecules, regarding charge generation, transport and extraction. The detailed study of terrylene-3,4:11,12-bis(dicarboximide) as electron acceptor for solar cells application was published in the peer review journal Synthetic Metals and was chosen to illustrate the cover page of the issue [5]. Finally, in the last chapter, we have used time resolved photoinduced absorption to improve the understanding of the charge carrier loss mechanisms in P3HT:PCBM active layers. This comprehension is of prime importance because, the fact that this recombination is far weaker than expected from the Langevin theory, enable polarons to travel further without recombining and thus to build thicker and more efficient devices. A comprehensive analysis of steady-state PIA spectra of pure P3HT, indicates that probing at 980 nm at a temperature between 140 and 250 K enables to monitor specifically polaron densities in both neat P3HT and P3HT:PCBM. Applying this finding to transient absorption enabled us to monitor, for the first time, the bimolecular recombination in pure P3HT, and to discover that - in sharp contrast with the blend - this recombination was in agreement with the Langevin theory. Moreover, it enables us to pinpoint the important role played by the existence of two materials and of energetical traps in the slow recombination and high recombination orders observed in the blend. This work has been published in the Journal of Applied Physics.[6] Those new insights in the photophysics of polymer:fullerene photoactive layers could have a strong impact on the future developement of those materials. Consistent measurements of the binding energy of excitons and intermediate species, would enable to clarify the role played by excess thermal energy in interfacial states dissociation. Better understanding of blends morphology and its influence on solar cells parameters and in particular on recombination could enable to reproduce the conditions of limited recombination on material systems offering some promising performances but with only limited active layer thicknesses. However, due to the number of parameters involved, further experimentation is required, before we can reach a quantitative modeling of bimolecular recombination. [1] Deibel et al., Phys. Rev. B, 81:085202, 2010 [2] Gorenflot et al., Deutsche Physikalische Gesellschaft Fr{\"u}hjahrstagung 2010, CPP20:10, Regensburg, Germany, 2010 [3] Gorenflot et al., International Conference of Synthetic Metals, 7Ax:05, Kyoto, Japan, 2010 [4] Marie-Curie RTN "SolarNTyp" Contract No. MRTN-CT-2006-035533 [5] Gorenflot et al., Synth. Met., 161(23{24):2669-2676, 2012 [6] Gorenflot et al., J. Appl. Phys., 115(14):144502, 2014}, subject = {Organische Solarzelle}, language = {en} } @phdthesis{Gieseking2014, author = {Gieseking, Bj{\"o}rn}, title = {Excitation Dynamics and Charge Carrier Generation in Organic Semiconductors}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-101625}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {The transport of optically excited states, called excitons, as well as their conversion into charges define the two major steps allowing for the operation of organic photovoltaic (OPV) devices. Hence, a deep understanding of these processes, the involved mechanisms as well as possible loss channels is crucial for further improving the efficiency of organic solar cells. For studying the aforementioned processes spectroscopic methods like absorption and emission measurements are useful tools. As many of the processes take place on a sub-nanosecond (ns) timescale ultrafast spectroscopic methods are required. Due to this reason two experiments based on a femtosecond laser system were built and employed in this work, namely picosecond (ps) time-resolved photoluminescence (PL) and transient absorption (TA) spectroscopy. By analyzing the PL decay dynamics in the prototypical organic semiconductor rubrene, the feasibility of a new approach for improving the efficiency of organic solar cells by harvesting triplet excitons generated by singlet fission was examined. Singlet fission describes a process where two triplet excitons are generated via a photoexcited singlet exciton precursor state if the energy of the two triplets is comparable with the energy of the singlet. For this purpose the influence of characteristic length scales on the exciton dynamics in different rubrene morphologies exhibiting an increasing degree of confinement was analyzed. The results show that the quenching at interfacial states efficiently suppresses the desired fission process if these states are reached by excitons during migration. Since interfacial states are expected to play a significant role in thin film solar cells and are easily accessible for the migrating excitons, the results have to be considered for triplet-based OPV. While the aforementioned approach is only investigated for model systems so far, the efficiency of disordered organic bulk heterojunction (BHJ) solar cells could be significantly enhanced in the last couple of years by employing new and more complex copolymer donor materials. However, little is known about the photophysics and in particular the excitation dynamics of these systems. By carrying out a systematic optical study on the prominent copolymer PCDTBT and its building blocks we were able to identify the nature of the two characteristic absorption bands and the coupling mechanism between these levels. The latter mechanism is based on an intrachain partial charge transfer between two functional subunits and our time-resolved measurements indicate that this coupling governs the photophysical properties of solar cells based on these copolymers. The efficient coupling of functional subunits can be seen as a key aspect that guarantees for the success of the copolymer approach. Another important issue concerns the optimization of the morphology of BHJ solar cells. It arises from the discrepancy between the exciton diffusion length \mbox{(\$\approx\$ 10 nm)} and the absorption length of solar irradiation (\$\approx\$ 100 nm). Due to this reason, even for devices based on new copolymer materials, processing parameters affecting the morphology like annealing or employing processing additives are of major importance. In our combined optical, electrical and morphological study for solar cells based on the high-efficient copolymer PBDTTT-C we find a direct correlation between additive content and intermixing of the active layer. The observed maximum in device efficiency can be attributed to a morphology guaranteeing for an optimized balance between charge generation and transport. Our results highlight the importance of understanding the influence of processing parameters on the morphology of the BHJ and thus on the efficiency of the device.}, subject = {Organische Solarzelle}, language = {en} } @phdthesis{Wagenpfahl2013, author = {Wagenpfahl, Alexander Johannes}, title = {Numerical simulations on limitations and optimization strategies of organic solar cells}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-90119}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2013}, abstract = {Continuously increasing energy prices have considerably influenced the cost of living over the last decades. At the same time increasingly extreme weather conditions, drought-filled summers as well as autumns and winters with heavier rainfall and worsening storms have been reported. These are possibly the harbingers of the expected approaching global climate change. Considering the depletability of fossil energy sources and a rising distrust in nuclear power, investigations into new and innovative renewable energy sources are necessary to prepare for the coming future. In addition to wind, hydro and biomass technologies, electricity generated by the direct conversion of incident sunlight is one of the most promising approaches. Since the syntheses and detailed studies of organic semiconducting polymers and fullerenes were intensified, a new kind of solar cell fabrication became conceivable. In addition to classical vacuum deposition techniques, organic cells were now also able to be processed from a solution, even on flexible substrates like plastic, fabric or paper. An organic solar cell represents a complex electrical device influenced for instance by light interference for charge carrier generation. Also charge carrier recombination and transport mechanisms are important to its performance. In accordance to Coulomb interaction, this results in a specific distribution of the charge carriers and the electric field, which finally yield the measured current-voltage characteristics. Changes of certain parameters result in a complex response in the investigated device due to interactions between the physical processes. Consequently, it is necessary to find a way to generally predict the response of such a device to temperature changes for example. In this work, a numerical, one-dimensional simulation has been developed based on the drift-diffusion equations for electrons, holes and excitons. The generation and recombination rates of the single species are defined according to a detailed balance approach. The Coulomb interaction between the single charge carriers is considered through the Poisson equation. An analytically non-solvable differential equation system is consequently set-up. With numerical approaches, valid solutions describing the macroscopic processes in organic solar cells can be found. An additional optical simulation is used to determine the spatially resolved charge carrier generation rates due to interference. Concepts regarding organic semiconductors and solar cells are introduced in the first part of this work. All chapters are based on previous ones and logically outline the basic physics, device architectures, models of charge carrier generation and recombination as well as the mathematic and numerical approaches to obtain valid simulation results. In the second part, the simulation is used to elaborate issues of current interest in organic solar cell research. This includes a basic understanding of how the open circuit voltage is generated and which processes limit its value. S-shaped current-voltage characteristics are explained assigning finite surface recombination velocities at metal electrodes piling-up local space charges. The power conversion efficiency is identified as a trade-off between charge carrier accumulation and charge extraction. This leads to an optimum of the power conversion efficiency at moderate to high charge carrier mobilities. Differences between recombination rates determined by different interpretations of identical experimental results are assigned to a spatially inhomogeneous recombination, relevant for almost all low mobility semiconductor devices.}, subject = {Organische Solarzelle}, language = {en} } @phdthesis{Kern2013, author = {Kern, Julia}, title = {Field Dependence of Charge Carrier Generation in Organic Bulk Heterojunction Solar Cells}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-91963}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2013}, abstract = {In the field of organic photovoltaics, one of the most intensely researched topics to date is the charge carrier photogeneration in organic bulk heterojunction solar cells whose thorough understanding is crucial for achieving higher power conversion efficiencies. In particular, the mechanism of singlet exciton dissociation at the polymer-fullerene interface is still controversially debated. This work addresses the dissociation pathway via relaxed charge transfer states (CTS) by investigating its field dependence for reference material systems consisting of MDMO-PPV and one of the fullerene derivatives PC61BM, bisPCBM and PC71BM. Field dependent photoluminescence (PL(F)) and transient absorption (TA(F)) measurements give insight into the recombination of charge transfer excitons (CTE) and the generation of polarons, respectively. Optically detected magnetic resonance and atomic force microscopy are used to characterize the morphology of the samples. The comparison of the experimental field dependent exciton recombination recorded by PL(F) and the theoretical exciton dissociation probability given by the Onsager-Braun model yields the exciton binding energy as one of the key parameters determining the dissociation efficiency. The binding energies of both the singlet exciton in neat MDMO-PPV and the CTE in MDMO-PPV:PC61BM 1:1 are extracted, the latter turning out to be significantly reduced with respect to the one of the singlet exciton. Based on these results, the field dependence of CTE dissociation is evaluated for MDMO-PPV:PC61BM blends with varying fullerene loads by PL(F) and TA(F). For higher PC61BM contents, the CTE binding energies decrease notably. This behavior is ascribed to a larger effective dielectric constant for well-intermixed blends and to an interplay between dielectric constant and CTE delocalization length for phase separated morphologies, emphasizing the importance of high dielectric constants for the charge carrier photogeneration process. Finally, the CTE binding energies are determined for MDMO-PPV blends with different fullerene derivatives, focusing on the influence of the acceptor LUMO energy. Here, the experimental results suggest the latter having no or at least no significant impact on the binding energy of the CTE. Variations of this binding energy are rather related to different trap levels in the acceptors which seem to be involved in CTS formation.}, subject = {Organische Solarzelle}, language = {en} } @phdthesis{Hartmann2012, author = {Hartmann, Fabian}, title = {Elektrooptische Transporteigenschaften und stochastisch aktivierte Prozesse Resonanter Tunneldioden}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-90876}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2012}, abstract = {Im Rahmen der vorliegenden Arbeit wurden elektrooptische Transporteigenschaften und stochastisch aktivierte Prozesse Resonanter Tunneldioden (RTDs) bei Raumtemperatur untersucht. Die RTDs wurden auf dem III-V Halbleitermaterialsystem AlGaAs/GaAs durch Molekularstrahlepitaxie, Elektronenstrahllithographie und trockenchemischen {\"A}tztechniken hergestellt. Im Bereich des negativen differentiellen Leitwerts konnte bistabi-les Schalten und hierbei stochastisch aktivierte Dynamik nichtlinearer Systeme untersucht werden. Die Fl{\"a}chenabh{\"a}ngigkeit der {\"A}tzrate konnte ausgenutzt werden, um RTDs mit einem Stamm und zwei Transport{\"a}sten zu realisieren, welche hinsichtlich ihrer optischen und elektrischen Eigenschaften untersucht wurden. Im ersten experimentellen Abschnitt 3.1 werden die elektrischen Transporteigenschaften Resonanter Tunneldioden bei Raum-temperatur und die Fl{\"a}chenabh{\"a}ngigkeit des koh{\"a}renten und nicht-koh{\"a}renten Elektronen-transports analysiert. Die Realisierung universeller logischer Gatter (NOR und NAND) und deren Rekonfigurierbarkeit durch einen externen Kontrollparameter wird in Abschnitt 3.2 gezeigt. In Abschnitt 3.3 wird die Lichtsensitivit{\"a}t Resonanter Tunneldioden als Photode-tektoren f{\"u}r den sichtbaren Wellenl{\"a}ngenbereich und in Abschnitt 3.4 f{\"u}r die Telekommu-nikationswellenl{\"a}nge bei λ = 1,3 µm demonstriert.}, subject = {Resonanz-Tunneldiode}, language = {de} } @phdthesis{Rauh2013, author = {Rauh, Daniel}, title = {Impact of Charge Carrier Density and Trap States on the Open Circuit Voltage and the Polaron Recombination in Organic Solar Cells}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-90083}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2013}, abstract = {The focus of this work is studying recombination mechanisms occurring in organic solar cells, as well as their impact on one of their most important parameters — the open circuit voltage Voc. Firstly, the relationship between Voc and the respective charge carrier density n in the active layer under open circuit conditions is analyzed. Therefor, a model after Shockley for the open circuit voltage is used, whose validity is proven with the aid of fits to the measured data. Thereby, it is emphasized that the equation is only valid under special conditions. In the used reference system P3HT:PC61BM the fits are in agreement with the measurement data only in the range of high temperatures (150 - 300 K), where Voc increases linearly with decreasing temperature. At lower temperatures (50 - 150 K), the experiment shows a saturation of Voc. This saturation cannot be explained with the model by the measured falling charge carrier density with decreasing temperatures. In this temperature range Voc is not directly related to the intrinsic properties of the active layer. Voc saturation is due to injection energy barriers at the contacts, which is ascertained by macroscopic simulations. Furthermore, it is observed that Voc in the case of saturation is equivalent to the so-called built-in potential. The difference between the built-in potential and the energy gap corresponds thereby to the sum of the energy barriers at both contacts. With the knowledge of the Voc(n) dependency for not contact limited solar cells, it is possible to investigate the recombination mechanisms of charge carriers in the active layer. For Langevin recombination the recombination rate is Rn2 (recombination order RO = 2), for Shockley-Read-Hall (SRH) Rn1 (RO=1); in various publications RO higher than two is reported with two main explanations. 1: Trap states for charge carriers exist in the respective separated phases, i.e. electrons in the acceptor phase and holes in the donor phase, which leads to a delayed recombination of the charge carriers at the interface of both phases and finally to an apparent recombination order higher than 2. 2: The enhanced R(n) dependency is attributed to the so called recombination prefactor, which again is dependent from n dependent mobility µ. It is shown that for the system P3HT:PC61BM at room temperature the µ(n) dependency does nearly completely explain the higher RO but not at lower temperatures which in this case supports the first explanation. In the material system PTB7:PC71BM the increased RO cannot be explained by the µ(n) dependency even at room temperature. To support the importance of trap states in combination with a phase separation for the explanation of the enhanced RO, additional trap states were incorporated in the solar cells to investigate their influence on the recombination mechanisms. To achieve this, P3HT:PC61BM solar cells were exposed to synthetic air (in the dark and under illumination) or TCNQ was added in small concentrations to the active layer which act as electron traps. For the oxygen degraded solar cell the recombination order is determined by a combination of open Voc-transients and Voc(n) measurements. Thereby, a continuous increase of the recombination order from 2.4 to more than 5 is observed with higher degradation times. By the evaluation of the ideality factor it can be shown that the impact of SRH recombination is increasing with higher trap concentration in relation to Langevin recombination. A similar picture is revealed for solar cells with TCNQ as extrinsic trap states. Finally, a phenomenon called s-shaped IV-curves is investigated, which can sometimes occur for solar cells under illumination. As course of this a reduced surface recombination velocity can be found. Experimentally, the solar cells were fabricated using a special plasma treatment of the ITO contact. The measured IV-curves of such solar cells are reproduced by macroscopic simulations, where the surface recombination velocity is reduced. Hereby, it has to be distinguished between the surface recombination of majority and minority charge carriers at the respective contacts. The theory can be experimentally confirmed by illumination level dependent IV-curves as well as short circuit current density and open circuit voltage transients.}, subject = {Organische Solarzelle}, language = {en} } @phdthesis{Kiermasch2020, author = {Kiermasch, David}, title = {Charge Carrier Recombination Dynamics in Hybrid Metal Halide Perovskite Solar Cells}, doi = {10.25972/OPUS-20862}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-208629}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2020}, abstract = {In order to facilitate the human energy needs with renewable energy sources in the future, new concepts and ideas for the electricity generation are needed. Solar cells based on metal halide perovskite semiconductors represent a promising approach to address these demands in both single-junction and tandem configurations with existing silicon technology. Despite intensive research, however, many physical properties and the working principle of perovskite PVs are still not fully understood. In particular, charge carrier recombination losses have so far mostly been studied on pure films not embedded in a complete solar cell. This thesis aimed for the identification and quantification of charge carrier recombination dynamics in fully working devices under conditions corresponding to those under real operation. To study different PV systems, transient electrical methods, more precisely Open-Circuit Voltage Decay (OCVD), Transient Photovoltage (TPV) and Charge Extraction (CE), were applied. Whereas OCVD and TPV provide information about the recombination lifetime, CE allows to access the charge carrier density at a specific illumination intensity. The benefit of combining these different methods is that the obtained quantities can not only be related to the Voc but also to each other, thus enabling to determine also the dominant recombination mechanisms.The aim of this thesis is to contribute to a better understanding of recombination losses in fully working perovskite solar cells and the experimental techniques which are applied to determine these losses.}, subject = {Solarzelle}, language = {en} } @phdthesis{Hoecker2022, author = {H{\"o}cker, Julian Harald}, title = {High-quality Organolead Trihalide Perovskite Crystals: Growth, Characterisation, and Photovoltaic Applications}, doi = {10.25972/OPUS-25859}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-258590}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {Overview of the Organolead Trihalide Perovskite Crystal Area Studies of perovskite single crystals with high crystallographic quality is an important technological area of the perovskite research, which enables to estimate their full optoelectronic potential, and thus to boost their future applications [26]. It was therefore essential to grow high-quality single crystals with lowest structural as well as chemical defect densities and with a stoichiometry relevant for their thin-film counterparts [26]. Optoelectronic devices, e.g. solar cells, are highly complex systems in which the properties of the active layer (absorber) are strongly influenced by the adjacent layers, so it is not always easy to define the targeted properties and elaborate the design rules for the active layer. Currently, organolead trihalide perovskite (OLTP) single crystals with the structure ABX3 are one of the most studied crystalline systems. These hybrid crystals are solids composed of an organic cation such as methylammonium (A = MA+) or formamidinium (A = FA+) to form a three-dimensional periodic lattice together with the lead cation (B = Pb2+) and a halogen anion such as chloride, bromide or iodide (X = Cl-, Br- or I-) [23]. Among them are methylammonium lead tribromide (MAPbBr3), methylammonium lead triiodide (MAPbI3), as well as methylammonium lead trichloride (MAPbCl3) [62, 63]. Important representatives with the larger cation FA+ are formamidinium lead tribromide (FAPbBr3) and formamidinium lead triiodide (FAPbI3) [23, 64]. Besides the exchange of cations as well as anions, it was possible to grow crystals containing two halogens to obtain mixed crystals with different proportions of chlorine to bromine and bromine to iodine, as it is shown in Figure 70. By varying the mixing ratio of the halogens, it was therefore possible to vary the colour and thus the absorption properties of the crystals [85], as it can be done with thin polycrystalline perovskite films. In addition, since a few years it is also doable to grow complex crystals that contain several cations as well as anions [26, 80, 81]. These include the perovskites double cation - double halide formamidinium lead triiodide - methylammonium lead tribromide (FAPbI3)0.9(MAPbBr3)0.1 (FAMA) [26, 80] and formamidinium lead triiodide - methylammonium lead tribromide - caesium lead tribromide (FAPbI3)0.9(MAPbBr3)0.05(CsPbBr3)0.05 (CsFAMA) [81], which have made a significant contribution to increase the power conversion efficiency (PCE) in thin-film photovoltaics [47, 79, 182]. The growth of crystals to this day is performed exclusively from solution [23, 26, 56, 62]. Important preparation methods are the cooling acid-based precursor solution crystallisation [22], the inverse temperature crystallisation (ITC) [62], and the antisolvent vapour-assistant crystallisation (AVC) [137]. In the cooling crystallisation, the precursor salts AX and PbX2 are dissolved in an aqueous halogen-containing acid at high temperatures [56]. Controlled and slow cooling finally results in a supersaturated precursor solution, which leads to spontaneous nucleation of crystal nuclei, followed by subsequent crystal growth. The ITC method is based on the inverse or retrograde solubility of a dissociated perovskite in an organic solvent [23, 64]. With increasing temperature, the solubility of the perovskite decreases and mm-sized crystals can be grown within a few hours [23]. In the AVC method, the precursors are also dissolved in an organic solvent as well [137]. By slow evaporation of a so-called antisolvent [137], the solubility of the perovskite in the now present solvent mixture decreases and it finally precipitates. In addition, there are many other methods with the goal of growing high quality and large crystals in a short period of time [60, 61, 233, 310].}, subject = {Perowskit}, language = {en} } @phdthesis{Fischer2023, author = {Fischer, Mathias}, title = {Transient Phenomena and Ionic Kinetics in Hybrid Metal Halide Perovskite Solar Cells}, doi = {10.25972/OPUS-32220}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-322204}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2023}, abstract = {The fact that photovoltaics is a key technology for climate-neutral energy production can be taken as a given. The question to what extent perovskite will be used for photovoltaic technologies has not yet been fully answered. From a photophysical point of view, however, it has the potential to make a useful contribution to the energy sector. However, it remains to be seen whether perovskite-based modules will be able to compete with established technologies in terms of durability and cost efficiency. The additional aspect of ionic migration poses an additional challenge. In the present work, primarily the interaction between ionic redistribution, capacitive properties and recombination dynamics was investigated. This was done using impedance spectroscopy, OCVD and IV characteristics as well as extensive numerical drift-diffusion simulations. The combination of experimental and numerical methods proved to be very fruitful. A suitable model for the description of solar cells with respect to mobile ions was introduced in chapter 4.4. The formal mathematical description of the model was transferred by a non-dimensionalization and suitable numerically solvable form. The implementation took place in the Julia language. By intelligent use of structural properties of the sparse systems of equations, automatic differentiation and the use of efficient integration methods, the simulation tool is not only remarkably fast in finding the solution, but also scales quasi-linearly with the grid resolution. The software package was released under an open source license. In conventional semiconductor diodes, capacitance measurements are often used to determine the space charge density. In the first experimental chapter 5, it is shown that although this is also possible for the ionic migration present in perovskites, it cannot be directly understood as doping related, since the space charge distribution strongly depends on the preconditions and can be manipulated by an externally applied voltage. The exact form of this behavior depends on the perovskite composition. This shows, among other things, that experimental results can only be interpreted within the framework of conventional semiconductors to a very limited extent. Nevertheless, the built-in 99 potential of the solar cell can be determined if the experiments are carried out properly. A statement concerning the type and charge of the mobile ions is not possible without further effort, while their number can be determined. The simulations were applied to experimental data in chapter 6. Thus, it could be shown that mobile ions make a significant contribution to the OCVD of perovskite solar cells. j-V characteristics and OCVD transients measured as a function of temperature and illumination intensities could be quantitatively modeled simultaneously using a single global set of parameters. By the simulations it was further possible to derive a simple experimental procedure to determine the concentration and the diffusivity of the mobile ions. The possibility of describing different experiments in a uniform temperaturedependent manner strongly supports the model of mobile ions in perovskites. In summary, this work has made an important contribution to the elucidation of ionic contributions to the (photo)electrical properties of perovskite solar cells. Established experimental techniques for conventional semiconductors have been reinterpreted with respect to ionic mass transport and new methods have been proposed to draw conclusions on the properties for ionic transport. As a result, the published simulation tools can be used for a number of further studies.}, subject = {Simulation}, language = {en} } @phdthesis{Armer2023, author = {Armer, Melina Brigitte Melanie}, title = {High-Quality Lead-Free Double Perovskite Single Crystals and their Optical Properties}, doi = {10.25972/OPUS-32750}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-327503}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2023}, abstract = {The presented thesis deals with the investigation of the characteristic physical properties of lead-free double perovskites. For this purpose lead-free double perovskite single crystals were grown from solution. In order to assess the influence of growth temperature on tail states in the material, the crystals were studied using Photoluminescence Excitation (PLE) and Transmission measurements. Additionally, lead-free double perovskite solar cells and thin films were investigated to address the correlation of precursor stoichiometry and solar cell efficiency. In a last step a new earth abundant lead-free double perovskite was introduced and its physical properties were studied by photoluminescene and absorptance. Like this it was possible to assess the suitability of this material for solar cell applications in the future.}, subject = {Perowskit}, language = {en} } @phdthesis{Simin2017, author = {Simin, Dmitrij}, title = {Quantum Sensing with Highly Coherent Spin Centers in Silicon Carbide}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-156199}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2017}, abstract = {In the present work, the energetic structure and coherence properties of the silicon vacancy point defect in the technologically important material silicon carbide are extensively studied by the optically detected magnetic resonance (ODMR) technique in order to verify its high potential for various quantum applications. In the spin vacancy, unique attributes are arising from the C3v symmetry and the spin-3/2 state, which are not fully described by the standard Hamiltonian of the uniaxial model. Therefore, an advanced Hamiltonian, describing well the appearing phenomena is established and the relevant parameters are experimentally determined. Utilizing these new accomplishments, several quantum metrology techniques are proposed. First, a vector magnetometry scheme, utilizing the appearance of four ODMR lines, allows for simultaneous detection of the magnetic field strength and the tilting angle of the magnetic field from the symmetry axis of the crystal. The second magnetometry protocol utilizes the appearance of energetic level anticrossings (LAC) in the ground state (GS) energy levels. Relying only on the change in photoluminescence in the vicinity of this GSLACs, this all-optical method does not require any radio waves and hence provides a much easier operation with less error sources as for the common magnetometry schemes utilizing quantum points. A similar all-optical method is applied for temperature sensing, utilizing the thermal shift of the zero field splitting and consequently the anticrossing in the excited state (ES). Since the GSLACs show no dependence on temperature, the all-optical magnetometry and thermometry (utilizing the ESLACs) can be conducted subsequently on the same defect. In order to quantify the achievable sensitivity of quantum metrology, as well as to prove the potential of the Si-vacancy in SiC for quantum processing, the coherence properties are investigated by the pulsed ODMR technique. The spin-lattice relaxation time T1 and the spin-spin relaxation time T2 are thoroughly analyzed for their dependence on the external magnetic field and temperature. For actual sensing implementations, it is crucial to obtain the best signal-to-noise ratio without loss in coherence time. Therefore, the irradiation process, by which the defects are created in the crystal, plays a decisive role in the device performance. In the present work, samples irradiated with electrons or neutrons with different fluences and energies, producing different defect densities, are analyzed in regard to their T1 and T2 times at room temperature. Last but not least, a scheme to substantially prolong the T2 coherence time by locking the spin polarization with the dynamic decoupling Carr-Purcell-Meiboom-Gill (CPMG) pulse sequence is applied.}, subject = {Siliciumcarbid}, language = {en} } @phdthesis{Gottscholl2022, author = {Gottscholl, Andreas Paul}, title = {Optical Accessible Spin Defects in Hexagonal Boron Nitride: Identification, Control and Application of the Negatively Charged Boron Vacancy VB-}, doi = {10.25972/OPUS-27432}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-274326}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {In this work, a bridge was built between the so-far separate fields of spin defects and 2D systems: for the first time, an optically addressable spin defect (VB-) in a van der Waals material (hexagonal boron nitride) was identified and exploited. The results of this thesis are divided into three topics as follows: 1.) Identification of VB-: In the scope of this chapter, the defect ,the negatively charged boron vacancy VB-, is identified and characterized. An initialization and readout of the spin state can be demonstrated optically at room temperature and its spin Hamiltonian contributions can be quantified. 2.) Coherent Control of VB-: A coherent control is required for the defect to be utilized for quantum applications, which}, subject = {Bornitrid}, language = {en} } @phdthesis{Auth2020, author = {Auth, Michael Tilman}, title = {Quantitative Electron Paramagnetic Resonance Studies of Charge Transfer in Organic Semiconductors}, doi = {10.25972/OPUS-18951}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-189513}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2020}, abstract = {In the present work we investigated various charge transfer processes, as they appear in the versatile world of organic semiconductors by probing the spin states of the corresponding charge carrier species via electron paramagnetic resonance (EPR) spectroscopy. All studied material systems are carbon-based compounds, either belonging to the group of polymers, fullerenes, or single-wall carbon nanotubes (SWNTs). In the first instance, we addressed the change of the open circuit voltage (Voc) with the fullerene blend stoichiometry in fullerene-based solar cells for organic photovoltaics (OPV). The voltage depends strongly on the energy separation between the lowest unoccupied molecular orbital (LUMO) of the donor and the highest occupied molecular orbital (HOMO) of the acceptor. By exploiting the Gaussian distribution of the charge carriers in a two-level system, and thus also their spins in the EPR experiment, it could be shown that the LUMOs get closer by a few to a few hundred meV when going from pure fullerene materials to a fullerene mixture. The reason for this strong energetic effect is likely the formation of a fullerene alloy. Further, we investigated the chemical doping mechanism of SWNTs with a (6,5)-chirality and their behaviour under optical excitation. In order to determine the unintentional (pre)-doping of SWNTs, EPR spectra of the raw material as well as after different purification steps were recorded. This facilitated the determination of nanotube defects and atmospheric p-doping as the causes of the measured EPR signals. In order to deliberately transfer additional charge carriers to the nanotubes, we added the redox-active substance AuCl3 where we determined an associated doping-yield of (1.5±0.2)\%. In addition, a statistical occupation model was developed which can be used to simulate the distribution of EPR active, i.e. unpaired and localised charge carriers on the nanotubes. Finally, we investigated the charge transfer behaviour of (6,5)-SWNTs together with the polymer P3HT and the fullerene PC60BM after optical excitation.}, subject = {Organische Halbleiter}, language = {en} } @phdthesis{Gruene2022, author = {Gr{\"u}ne, Jeannine}, title = {Spin States and Efficiency-Limiting Pathways in Optoelectronic Materials and Devices}, doi = {10.25972/OPUS-29340}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-293405}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {This thesis addresses the identification and characterization of spin states in optoelectronic materials and devices using multiple spin-sensitive techniques. For this purpose, a systematic study focussing on triplet states as well as associated loss pathways and excited state kinetics was carried out. The research was based on comparing a range of donor:acceptor systems, reaching from organic light emitting diodes (OLEDs) based on thermally activated delayed fluorescence (TADF) to organic photovoltaics (OPV) employing fullerene and multiple non-fullerene acceptors (NFAs). By developing new strategies, e.g., appropriate modeling, new magnetic resonance techniques and experimental frameworks, the influence of spin states in the fundamental processes of organic semiconductors has been investigated. Thereby, the combination of techniques based on the principle of electron paramagnetic resonance (EPR), in particular transient EPR (trEPR) and optically detected magnetic resonance (ODMR), with all-optical methods, such as transient electroluminescence (trEL) and transient absorption (TA), has been employed. As a result, excited spin states, especially molecular and charge transfer (CT) states, were investigated in terms of kinetic behavior and associated pathways, which revealed a significant impact of triplet states on efficiency-limiting processes in both optoelectronic applications.}, subject = {Elektronenspinresonanz}, language = {en} } @phdthesis{Balzer2018, author = {Balzer, Christian}, title = {Adsorption-Induced Deformation of Nanoporous Materials — in-situ Dilatometry and Modeling}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-157145}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2018}, abstract = {The goal of this work is to improve the understanding of adsorption-induced deformation in nanoporous (and in particular microporous) materials in order to explore its potential for material characterization and provide guidelines for related technical applications such as adsorption-driven actuation. For this purpose this work combines in-situ dilatometry measurements with in-depth modeling of the obtained adsorption-induced strains. A major advantage with respect to previous studies is the combination of the dilatometric setup and a commercial sorption instrument resulting in high quality adsorption and strain isotherms. The considered model materials are (activated and thermally annealed) carbon xerogels, a sintered silica aerogel, a sintered hierarchical structured porous silica and binderless zeolites of type LTA and FAU; this selection covers micro-, meso- and macroporous as well as ordered and disordered model materials. All sample materials were characterized by scanning electron microscopy, gas adsorption and sound velocity measurements. In-situ dilatometry measurements on mesoporous model materials were performed for the adsorption of N2 at 77 K, while microporous model materials were also investigated for CO2 adsorption at 273 K, Ar adsorption at 77 K and H2O adsorption at 298 K. Within this work the available in-situ dilatometry setup was revised to improve resolution and reproducibility of measurements of small strains at low relative pressures, which are of particular relevance for microporous materials. The obtained experimental adsorption and strain isotherms of the hierarchical structured porous silica and a micro-macroporous carbon xerogel were quantitatively analyzed based on the adsorption stress model; this approach, originally proposed by Ravikovitch and Neimark, was extended for anisotropic pore geometries within this work. While the adsorption in silica mesopores could be well described by the classical and analytical theory of Derjaguin, Broekhoff and de Boer, the adsorption in carbon micropores required for comprehensive nonlocal density functional theory calculations. To connect adsorption-induced stresses and strains, furthermore mechanical models for the respective model materials were derived. The resulting theoretical framework of adsorption, adsorption stress and mechanical model was applied to the experimental data yielding structural and mechanical information about the model materials investigated, i.e., pore size or pore size distribution, respectively, and mechanical moduli of the porous matrix and the nonporous solid skeleton. The derived structural and mechanical properties of the model materials were found to be consistent with independent measurements and/or literature values. Noteworthy, the proposed extension of the adsorption stress model proved to be crucial for the correct description of the experimental data. Furthermore, it could be shown that the adsorption-induced deformation of disordered mesoporous aero-/xerogel structures follows qualitatively the same mechanisms obtained for the ordered hierarchical structured porous silica. However, respective quantitative modeling proved to be challenging due to the ill-shaped pore geometry of aero-/xerogels; good agreement between model and experiment could only be achieved for the filled pore regime of the adsorption isotherm and the relative pressure range of monolayer formation. In the intermediate regime of multilayer formation a more complex model than the one proposed here is required to correctly describe stress related to the curved adsorbate-adsorptive interface. Notably, for micro-mesoporous carbon xerogels it could be shown that micro- and mesopore related strain mechanisms superimpose one another. The strain isotherms of the zeolites were only qualitatively evaluated. The result for the FAU type zeolite is in good agreement with other experiments reported in literature and the theoretical understanding derived from the adsorption stress model. On the contrary, the strain isotherm of the LTA type zeolite is rather exceptional as it shows monotonic expansion over the whole relative pressure range. Qualitatively this type of strain isotherm can also be explained by the adsorption stress model, but a respective quantitative analysis is beyond the scope of this work. In summary, the analysis of the model materials' adsorption-induced strains proved to be a suitable tool to obtain information on their structural and mechanical properties including the stiffness of the nonporous solid skeleton. Investigations on the carbon xerogels modified by activation and thermal annealing revealed that adsorption-induced deformation is particularly suited to analyze even small changes of carbon micropore structures.}, subject = {Nanopor{\"o}ser Stoff}, language = {en} } @phdthesis{Namal2018, author = {Namal, Imge}, title = {Fabrication and Optical and Electronic Characterization of Conjugated Polymer-Stabilized Semiconducting Single-Wall Carbon Nanotubes in Dispersions and Thin Films}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-162393}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2018}, abstract = {In order to shrink the size of semiconductor devices and improve their efficiency at the same time, silicon-based semiconductor devices have been engineered, until the material almost reaches its performance limits. As the candidate to be used next in semiconducting devices, single-wall carbon nanotubes show a great potential due to their promise of increased device efficiency and their high charge carrier mobilities in the nanometer size active areas. However, there are material based problems to overcome in order to imply SWNTs in the semiconductor devices. SWNTs tend to aggregate in bundles and it is not trivial to obtain an electronically or chirally homogeneous SWNT dispersion and when it is done, a homogeneous thin film needs to be produced with a technique that is practical, easy and scalable. This work was aimed to solve both of these problems. In the first part of this study, six different polymers, containing fluorene or carbazole as the rigid part and bipyridine, bithiophene or biphenyl as the accompanying copolymer unit, were used to selectively disperse semiconducting SWNTs. With the data obtained from absorption and photoluminescence spectroscopy of the corresponding dispersions, it was found out that the rigid part of the copolymer plays a primary role in determining its dispersion efficiency and electronic sorting ability. Within the two tested units, carbazole has a higher π electron density. Due to increased π-π interactions, carbazole containing copolymers have higher dispersion efficiency. However, the electronic sorting ability of fluorene containing polymers is superior. Chiral selection of the polymers in the dispersion is not directly foreseeable from the selection of backbone units. At the end, obtaining a monochiral dispersion is found to be highly dependent on the used raw material in combination to the preferred polymer. Next, one of the best performing polymers due to high chirality enrichment and electronic sorting ability was chosen in order to disperse SWNTs. Thin films of varying thickness between 18 ± 5 to 755o±o5 nm were prepared using vacuum filtration wet transfer method in order to analyze them optically and electronically. The scalability and efficiency of the integrated thin film production method were shown using optical, topographical and electronic measurements. The relative photoluminescence quantum yield of the radiative decay from the SWNT thin films was found to be constant for the thickness scale. Constant roughness on the film surface and linearly increasing concentration of SWNTs were also supporting the scalability of this thin film production method. Electronic measurements on bottom gate top contact transistors have shown an increasing charge carrier mobility for linear and saturation regimes. This was caused by the missing normalization of the mobility for the thickness of the active layer. This emphasizes the importance of considering this dimension for comparison of different field effect transistor mobilities.}, subject = {Feldeffekttransistor}, language = {en} } @phdthesis{Brendel2018, author = {Brendel, Harald}, title = {W{\"a}rmetransport in keramischen Faserisolationen bei hohen Temperaturen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-157917}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2018}, abstract = {Das Ziel dieser Arbeit ist eine umfassende numerische und experimentelle Charakterisierung des W{\"a}rmetransports in oxidkeramischen Faserisolationen im Hochtemperaturbereich. Zugleich sollen neue Konzepte f{\"u}r eine optimierte technische Auslegung von Faserisolationen erarbeitet werden. Oxidkeramiken zeigen im Infrarotbereich ein semitransparentes Verhalten. Das bedeutet, ein Teil der Strahlung gelangt durch die Probe, ohne gestreut oder absorbiert zu werden. Durch die Ausgestaltung als disperses Medium mit Abmessungen der Fasern im \$\mu m\$ Bereich wird jedoch eine starke Wechselwirkung mit infraroter Lichtstrahlung erzeugt. Man befindet sich im optischen Resonanzbereich. Technisch relevante Faserisolationen besitzen eine Rohdichte zwischen \$50 \mathrm{kg/m^3}\$ und \$700 \mathrm{kg/m^3}\$ und k{\"o}nnen als optisch dichtes Medium betrachtet werden. Eine Optimierung hinsichtlich der D{\"a}mmwirkung gegen W{\"a}rmestrahlung bedeutet eine massenspezifische Maximierung des Lichtstreuverm{\"o}gens im relevanten Wellenl{\"a}ngenbereich. Hierzu werden in einer numerischen Studie keramische Hohlfaserisolationen mit konventionellen Fasern verglichen. Diese Abhandlung unter Ber{\"u}cksichtigung anwendungsnaher Aspekte gelangt zu der Schlussfolgerung, dass die Strahlungsw{\"a}rmestromdichte in Hohlfaserisolationen, im Vergleich zu konventionellen Isolationen, signifikant erniedrigt wird. Hinsichtlich der Gesamtw{\"a}rmeleitf{\"a}higkeit ist eine Reduzierung um den Faktor zwei zu erwarten. \\ Trotz moderner Rechner ist die Anwendung der vollen Maxwellschen Streutheorie, insbesondere im Rahmen von Optimierungsaufgaben mehrschichtiger Streuk{\"o}rper, ein zeitaufwendiges Unterfangen. Um sinnvolle Parameterkonfigurationen bereichsweise eingrenzen zu k{\"o}nnen, wird eine N{\"a}herungsmethode f{\"u}r die Lichtstreuung an mehrschichtigen Zylindern weiterentwickelt und mit der vollst{\"a}ndigen Maxwellschen Streutheorie verglichen. Es zeigt sich, dass das Modell f{\"u}r kleine bis moderate Brechungsindizes sehr gute Vorhersagekraft besitzt und auch zur n{\"a}herungsweisen Berechnung der Streueffizienzen f{\"u}r r{\"a}umlich isotrop angeordnete Zylinder herangezogen werden kann. \\ Neben den numerischen Studien wird im experimentellen Teil dieser Arbeit eine kommerzielle Faserisolierung aus Aluminiumoxid hinsichtlich ihrer W{\"a}rmetransporteigenschaften charakterisiert. Die optischen Transportparameter Albedo und Extinktion werden mittels etablierter Messmethoden bestimmt. Bei bekannter Faserdurchmesserverteilung k{\"o}nnen diese Messwerte dann mit den theoretischen Vorhersagen der Maxwellschen Streutheorie verglichen werden.\\ Um technische Optimierungsmaßnahmen experimentell zu verifizieren, besteht die Notwendigkeit, die Temperaturleitf{\"a}higkeit bzw. die W{\"a}rmeleitf{\"a}higkeit auch bei hohen Temperaturen oberhalb von \$1000^\mathrm{o}\mathrm{C}\$ zuverl{\"a}ssig bestimmen zu k{\"o}nnen. Zu diesem Zweck wird ein Versuchsaufbau realisiert, um in diesem Temperaturbereich erstmals die sogenannte Thermal-Wave-Analyse anzuwenden. Durch Abgleich mit einem gekoppelten W{\"a}rmetransportmodell und einem etablierten Messverfahren wird die besondere Eignung der Thermal-Wave-Analyse f{\"u}r ber{\"u}hrungsfreie Hochtemperaturmessungen gezeigt.}, subject = {W{\"a}rme{\"u}bertragung}, language = {de} } @phdthesis{Kudriashova2019, author = {Kudriashova, Liudmila}, title = {Photoluminescence Reveals Charge Carrier Recombination in Organic and Hybrid Semiconductors}, doi = {10.25972/OPUS-19343}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-193437}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2019}, abstract = {In this work, we elucidated recombination kinetics in organic and hybrid semiconductors by steady-state and time-resolved PL spectroscopy. Using these simple and very flexible experimental techniques, we probed the infrared emission from recombining free charge carriers in metal-halide perovskites, as well as the deep blue luminescence from intramolecular charge-transfer states in novel OLED emitters. We showed that similar state diagrams and kinetic models accurately describe the dynamics of excited species in these very different material systems. In Chapters 4 and 5, we focused on lead iodide perovskites (MAPI and FAPI), whose comparatively developed deposition techniques suited the systematic material research. In MAPI, we harnessed the anomalous dependence of transient PL on the laser repetition rate in order to investigate the role of interfaces with the commonly used charge-selective layers: PC60BM, spiro-MeOTAD, and P3HT. The film was deposited on a large precut substrate and separated into several parts, which were then covered with the charge-selective layers. Thereby, the same bulk perovskite structure was maintained for all samples. Consequently, we were able to isolate interface-affected and bulk carrier recombination. The first one dominated the fast component of PL decay up to 300 ns, whereas the last was assigned to the remaining slow component. The laser repetition rate significantly prolonged PL decay in MAPI with additional interfaces while shortening the charge carrier lifetime in the pristine film. We qualitatively explained this effect by a kinetic model that included radiative electron-hole recombination and nonradiative trap-assisted recombination. All in all, we showed that the apparent PL lifetime in MAPI is to large extend defined by the laser repetition rate and by the adjacent interfaces. Further, we studied photon recycling in MAPI and FAPI. We monitored how the microscopic PL transforms while propagating through the thin perovskite film. The emission was recorded within 5orders of magnitude in intensity up to 70μm away from the excitation spot. The Beer-Lambert law previously failed to describe the complex interplay of the intrinsic PL spectrum and the additional red-shifted peak. Therefore, we developed a general numerical model that accounts for self-absorption and diffusion of the secondary charge carriers. A simulation based on this model showed excellent agreement with the experimental spatially resolved PL maps. The proposed model can be applied to any perovskite film, because it uses easily measurable intrinsic PL spectrum and macroscopic absorption coefficient as seeding parameters. In Chapter 6, we conducted an extensive photophysical study of a novel compact deep blue OLED emitter, SBABz4, containing spiro-biacridine and benzonitrile units. We also considered its single-donor monomer counterpart, DMABz4, in order to highlight the structure-property relationships. Both compounds exhibited thermally activated delayed fluorescence (TADF), which was independently proven by oxygen quenching and temperature-dependent transient PL measurements. The spiro-linkage in the double-donor core of SBABz4 rendered its luminescence pure blue compared to the blue-green emission from the single-donor DMABz4. Thus, the core-donor provided desirable color tuning in the deep blue region, as opposed to the common TADF molecular design with core-acceptor. Using PL lifetimes and efficiencies, we predicted EQEmax = 7.1\% for SBABz4-based OLED, whereas a real test device showed EQEmax = 6.8\%. Transient PL was recorded from the solutions and solid films in the unprecedentedly broad dynamic range covering up to 6orders of magnitude in time and 8orders of magnitude in intensity. The stretched exponent was shown to fit the transient PL in the films very well, whereas PL decay in dilute solution was found purely exponential. When the emitter was embedded in the host matrix that prevented aggregation, its TADF properties were superior in comparison with the pure SBABz4 film. Finally, using temperature-dependent transient PL data, we calculated the TADF activation energy of 70 meV. To sum up, this Thesis contributes to the two fascinating topics of the last decade's material research: perovskite absorbers for photovoltaics and TADF emitters for OLEDs. We were lucky to work with the emerging systems and tailor for them new models out of the well-known physical concepts. This was both exciting and challenging. In the end, science of novel materials is always a mess. We hope that we brought there a bit of clarity and light.}, subject = {Time-resolved photoluminescence}, language = {en} } @phdthesis{Weissenseel2022, author = {Weißenseel, Sebastian G{\"u}nter}, title = {Spin-Spin Interactions and their Impact on Organic Light-Emitting Devices}, doi = {10.25972/OPUS-25745}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-257458}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {This work investigates the correlations between spin states and the light emission properties of organic light-emitting diodes (OLEDs), which are based on the principle of thermally activated delayed fluorescence. The spin-spin interactions responsible for this mechanism are investigated in this work using methods based on spin-sensitive electron paramagnetic resonance (EPR). In particular, this method has been applied to electrically driven OLEDs. The magnetic resonance has been detected by electroluminescence, giving this method its name: electroluminescence detected magnetic resonance (ELDMR). Initial investigations on a novel deep blue TADF emitter were performed. Furthermore, the ELDMR method was used in this work to directly detect the spin states in the OLED. These measurements were further underlined by time-resolved experiments such as transient electro- and photoluminescence.}, subject = {Elektronenspinresonanz}, language = {en} } @phdthesis{Bunzmann2021, author = {Bunzmann, Nikolai Eberhard}, title = {Excited State Pathways in 3rd Generation Organic Light-Emitting Diodes}, doi = {10.25972/OPUS-22078}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-220786}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2021}, abstract = {This work revealed spin states that are involved in the light generation of organic light-emitting diodes (OLEDs) that are based on thermally activated delayed fluorescence (TADF). First, several donor:acceptor-based TADF systems forming exciplex states were investigated. Afterwards, a TADF emitter that shows intramolecular charge transfer states but also forms exciplex states with a proper donor molecule was studied. The primary experimental technique was electron paramagnetic resonance (EPR), in particular the advanced methods electroluminescence detected magnetic resonance (ELDMR), photoluminescence detected magnetic resonance (PLDMR) and electrically detected magnetic resonance (EDMR). Additional information was gathered from time-resolved and continuous wave photoluminescence measurements.}, subject = {Elektronenspinresonanz}, language = {en} } @phdthesis{Dusel2024, author = {Dusel, Marco}, title = {Exziton-Polariton-Kondensation in organischen Halbleiter-Mikrokavit{\"a}ten mit hemisph{\"a}rischen Potentiallandschaften}, doi = {10.25972/OPUS-37055}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-370554}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2024}, abstract = {Exziton-Polaritonen sind hybride Quasiteilchen, die entstehen durch die starke Kopplung zwischen Halbleiter-Exzitonen und Mikrokavit{\"a}tsphotonen in einem optischen Resonator. Aufgrund ihres bosonischen Charakters k{\"o}nnen die Polaritonen Kondensate ausbilden. In dieser Arbeit ist der emittierende organische Halbleiter das fluoreszierende Protein mCherry. Um einen r{\"a}umlichen Einschluss zu generieren wurden hemisph{\"a}rische Potentiale genutzt. Durch die Variation der Potentiallandschaft (Linse, Molek{\"u}l, Kette, Su-Schrieffer-Heeger-Kette und Honigwaben-Gitter) konnten Eigenschaften wie beispielsweise topologisch nicht-triviale Defekte experimentell bei Umgebungstemperatur demonstriert werden. Zusammengefasst besch{\"a}ftigt sich diese Arbeit mit der Exziton-Polartion Kondensation in unterschiedlichen Potentiallandschaften mit dem organischen Halbleiter mCherry.}, subject = {Exziton-Polariton}, language = {de} }