@phdthesis{Klein2010, author = {Klein, Alexander}, title = {Performance Issues of MAC and Routing Protocols in Wireless Sensor Networks}, doi = {10.25972/OPUS-4465}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-52870}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2010}, abstract = {The focus of this work lies on the communication issues of Medium Access Control (MAC) and routing protocols in the context of WSNs. The communication challenges in these networks mainly result from high node density, low bandwidth, low energy constraints and the hardware limitations in terms of memory, computational power and sensing capabilities of low-power transceivers. For this reason, the structure of WSNs is always kept as simple as possible to minimize the impact of communication issues. Thus, the majority of WSNs apply a simple one hop star topology since multi-hop communication has high demands on the routing protocol since it increases the bandwidth requirements of the network. Moreover, medium access becomes a challenging problem due to the fact that low-power transceivers are very limited in their sensing capabilities. The first contribution is represented by the Backoff Preamble-based MAC Protocol with Sequential Contention Resolution (BPS-MAC) which is designed to overcome the limitations of low-power transceivers. Two communication issues, namely the Clear Channel Assessment (CCA) delay and the turnaround time, are directly addressed by the protocol. The CCA delay represents the period of time which is required by the transceiver to detect a busy radio channel while the turnaround time specifies the period of time which is required to switch between receive and transmit mode. Standard Carrier Sense Multiple Access (CSMA) protocols do not achieve high performance in terms of packet loss if the traffic is highly correlated due to the fact that the transceiver is not able to sense the medium during the switching phase. Therefore, a node may start to transmit data while another node is already transmitting since it has sensed an idle medium right before it started to switch its transceiver from receive to transmit mode. The BPS-MAC protocol uses a new sequential preamble-based medium access strategy which can be adapted to the hardware capabilities of the transceivers. The protocol achieves a very low packet loss rate even in wireless networks with high node density and event-driven traffic without the need of synchronization. This makes the protocol attractive to applications such as structural health monitoring, where event suppression is not an option. Moreover, acknowledgments or complex retransmission strategies become almost unnecessary since the sequential preamble-based contention resolution mechanism minimizes the collision probability. However, packets can still be lost as a consequence of interference or other issues which affect signal propagation. The second contribution consists of a new routing protocol which is able to quickly detect topology changes without generating a large amount of overhead. The key characteristics of the Statistic-Based Routing (SBR) protocol are high end-to-end reliability (in fixed and mobile networks), load balancing capabilities, a smooth continuous routing metric, quick adaptation to changing network conditions, low processing and memory requirements, low overhead, support of unidirectional links and simplicity. The protocol can establish routes in a hybrid or a proactive mode and uses an adaptive continuous routing metric which makes it very flexible in terms of scalability while maintaining stable routes. The hybrid mode is optimized for low-power WSNs since routes are only established on demand. The difference of the hybrid mode to reactive routing strategies is that routing messages are periodically transmitted to maintain already established routes. However, the protocol stops the transmission of routing messages if no data packets are transmitted for a certain time period in order to minimize the routing overhead and the energy consumption. The proactive mode is designed for high data rate networks which have less energy constraints. In this mode, the protocol periodically transmits routing messages to establish routes in a proactive way even in the absence of data traffic. Thus, nodes in the network can immediately transmit data since the route to the destination is already established in advance. In addition, a new delay-based routing message forwarding strategy is introduced. The forwarding strategy is part of SBR but can also be applied to many routing protocols in order to modify the established topology. The strategy can be used, e.g. in mobile networks, to decrease the packet loss by deferring routing messages with respect to the neighbor change rate. Thus, nodes with a stable neighborhood forward messages faster than nodes within a fast changing neighborhood. As a result, routes are established through nodes with correlated movement which results in fewer topology changes due to higher link durations.}, subject = {Routing}, language = {en} } @phdthesis{Aschenbrenner2017, author = {Aschenbrenner, Doris}, title = {Human Robot Interaction Concepts for Human Supervisory Control and Telemaintenance Applications in an Industry 4.0 Environment}, isbn = {978-3-945459-18-8}, doi = {10.25972/OPUS-15052}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-150520}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2017}, abstract = {While teleoperation of technical highly sophisticated systems has already been a wide field of research, especially for space and robotics applications, the automation industry has not yet benefited from its results. Besides the established fields of application, also production lines with industrial robots and the surrounding plant components are in need of being remotely accessible. This is especially critical for maintenance or if an unexpected problem cannot be solved by the local specialists. Special machine manufacturers, especially robotics companies, sell their technology worldwide. Some factories, for example in emerging economies, lack qualified personnel for repair and maintenance tasks. When a severe failure occurs, an expert of the manufacturer needs to fly there, which leads to long down times of the machine or even the whole production line. With the development of data networks, a huge part of those travels can be omitted, if appropriate teleoperation equipment is provided. This thesis describes the development of a telemaintenance system, which was established in an active production line for research purposes. The customer production site of Braun in Marktheidenfeld, a factory which belongs to Procter \& Gamble, consists of a six-axis cartesian industrial robot by KUKA Industries, a two-component injection molding system and an assembly unit. The plant produces plastic parts for electric toothbrushes. In the research projects "MainTelRob" and "Bayern.digital", during which this plant was utilised, the Zentrum f{\"u}r Telematik e.V. (ZfT) and its project partners develop novel technical approaches and procedures for modern telemaintenance. The term "telemaintenance" hereby refers to the integration of computer science and communication technologies into the maintenance strategy. It is particularly interesting for high-grade capital-intensive goods like industrial robots. Typical telemaintenance tasks are for example the analysis of a robot failure or difficult repair operations. The service department of KUKA Industries is responsible for the worldwide distributed customers who own more than one robot. Currently such tasks are offered via phone support and service staff which travels abroad. They want to expand their service activities on telemaintenance and struggle with the high demands of teleoperation especially regarding security infrastructure. In addition, the facility in Marktheidenfeld has to keep up with the high international standards of Procter \& Gamble and wants to minimize machine downtimes. Like 71.6 \% of all German companies, P\&G sees a huge potential for early information on their production system, but complains about the insufficient quality and the lack of currentness of data. The main research focus of this work lies on the human machine interface for all human tasks in a telemaintenance setup. This thesis provides own work in the use of a mobile device in context of maintenance, describes new tools on asynchronous remote analysis and puts all parts together in an integrated telemaintenance infrastructure. With the help of Augmented Reality, the user performance and satisfaction could be raised. A special regard is put upon the situation awareness of the remote expert realized by different camera viewpoints. In detail the work consists of: - Support of maintenance tasks with a mobile device - Development and evaluation of a context-aware inspection tool - Comparison of a new touch-based mobile robot programming device to the former teach pendant - Study on Augmented Reality support for repair tasks with a mobile device - Condition monitoring for a specific plant with industrial robot - Human computer interaction for remote analysis of a single plant cycle - A big data analysis tool for a multitude of cycles and similar plants - 3D process visualization for a specific plant cycle with additional virtual information - Network architecture in hardware, software and network infrastructure - Mobile device computer supported collaborative work for telemaintenance - Motor exchange telemaintenance example in running production environment - Augmented reality supported remote plant visualization for better situation awareness}, subject = {Fernwartung}, language = {en} } @phdthesis{Borrmann2018, author = {Borrmann, Dorit}, title = {Multi-modal 3D mapping - Combining 3D point clouds with thermal and color information}, isbn = {978-3-945459-20-1}, issn = {1868-7474}, doi = {10.25972/OPUS-15708}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-157085}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2018}, abstract = {Imagine a technology that automatically creates a full 3D thermal model of an environment and detects temperature peaks in it. For better orientation in the model it is enhanced with color information. The current state of the art for analyzing temperature related issues is thermal imaging. It is relevant for energy efficiency but also for securing important infrastructure such as power supplies and temperature regulation systems. Monitoring and analysis of the data for a large building is tedious as stable conditions need to be guaranteed for several hours and detailed notes about the pose and the environment conditions for each image must be taken. For some applications repeated measurements are necessary to monitor changes over time. The analysis of the scene is only possible through expertise and experience. This thesis proposes a robotic system that creates a full 3D model of the environment with color and thermal information by combining thermal imaging with the technology of terrestrial laser scanning. The addition of a color camera facilitates the interpretation of the data and allows for other application areas. The data from all sensors collected at different positions is joined in one common reference frame using calibration and scan matching. The first part of the thesis deals with 3D point cloud processing with the emphasis on accessing point cloud data efficiently, detecting planar structures in the data and registering multiple point clouds into one common coordinate system. The second part covers the autonomous exploration and data acquisition with a mobile robot with the objective to minimize the unseen area in 3D space. Furthermore, the combination of different modalities, color images, thermal images and point cloud data through calibration is elaborated. The last part presents applications for the the collected data. Among these are methods to detect the structure of building interiors for reconstruction purposes and subsequent detection and classification of windows. A system to project the gathered thermal information back into the scene is presented as well as methods to improve the color information and to join separately acquired point clouds and photo series. A full multi-modal 3D model contains all the relevant geometric information about the recorded scene and enables an expert to fully analyze it off-site. The technology clears the path for automatically detecting points of interest thereby helping the expert to analyze the heat flow as well as localize and identify heat leaks. The concept is modular and neither limited to achieving energy efficiency nor restricted to the use in combination with a mobile platform. It also finds its application in fields such as archaeology and geology and can be extended by further sensors.}, subject = {Punktwolke}, language = {en} } @phdthesis{Houshiar2017, author = {Houshiar, Hamidreza}, title = {Documentation and mapping with 3D point cloud processing}, isbn = {978-3-945459-14-0}, doi = {10.25972/OPUS-14449}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-144493}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2017}, abstract = {3D point clouds are a de facto standard for 3D documentation and modelling. The advances in laser scanning technology broadens the usability and access to 3D measurement systems. 3D point clouds are used in many disciplines such as robotics, 3D modelling, archeology and surveying. Scanners are able to acquire up to a million of points per second to represent the environment with a dense point cloud. This represents the captured environment with a very high degree of detail. The combination of laser scanning technology with photography adds color information to the point clouds. Thus the environment is represented more realistically. Full 3D models of environments, without any occlusion, require multiple scans. Merging point clouds is a challenging process. This thesis presents methods for point cloud registration based on the panorama images generated from the scans. Image representation of point clouds introduces 2D image processing methods to 3D point clouds. Several projection methods for the generation of panorama maps of point clouds are presented in this thesis. Additionally, methods for point cloud reduction and compression based on the panorama maps are proposed. Due to the large amounts of data generated from the 3D measurement systems these methods are necessary to improve the point cloud processing, transmission and archiving. This thesis introduces point cloud processing methods as a novel framework for the digitisation of archeological excavations. The framework replaces the conventional documentation methods for excavation sites. It employs point clouds for the generation of the digital documentation of an excavation with the help of an archeologist on-site. The 3D point cloud is used not only for data representation but also for analysis and knowledge generation. Finally, this thesis presents an autonomous indoor mobile mapping system. The mapping system focuses on the sensor placement planning method. Capturing a complete environment requires several scans. The sensor placement planning method solves for the minimum required scans to digitise large environments. Combining this method with a navigation system on a mobile robot platform enables it to acquire data fully autonomously. This thesis introduces a novel hole detection method for point clouds to detect obscured parts of a captured environment. The sensor placement planning method selects the next scan position with the most coverage of the obscured environment. This reduces the required number of scans. The navigation system on the robot platform consist of path planning, path following and obstacle avoidance. This guarantees the safe navigation of the mobile robot platform between the scan positions. The sensor placement planning method is designed as a stand alone process that could be used with a mobile robot platform for autonomous mapping of an environment or as an assistant tool for the surveyor on scanning projects.}, subject = {3D Punktwolke}, language = {en} } @phdthesis{Schlosser2011, author = {Schlosser, Daniel}, title = {Quality of Experience Management in Virtual Future Networks}, doi = {10.25972/OPUS-5719}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-69986}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2011}, abstract = {Aktuell beobachten wir eine drastische Vervielf{\"a}ltigung der Dienste und Anwendungen, die das Internet f{\"u}r den Datentransport nutzen. Dabei unterscheiden sich die Anforderungen dieser Dienste an das Netzwerk deutlich. Das Netzwerkmanagement wird durch diese Diversit{\"a}t der nutzenden Dienste aber deutlich erschwert, da es einem Datentransportdienstleister kaum m{\"o}glich ist, die unterschiedlichen Verbindungen zu unterscheiden, ohne den Inhalt der transportierten Daten zu analysieren. Netzwerkvirtualisierung ist eine vielversprechende L{\"o}sung f{\"u}r dieses Problem, da sie es erm{\"o}glicht f{\"u}r verschiedene Dienste unterschiedliche virtuelle Netze auf dem gleichen physikalischen Substrat zu betreiben. Diese Diensttrennung erm{\"o}glicht es, jedes einzelne Netz anwendungsspezifisch zu steuern. Ziel einer solchen Netzsteuerung ist es, sowohl die vom Nutzer erfahrene Dienstg{\"u}te als auch die Kosteneffizienz des Datentransports zu optimieren. Dar{\"u}ber hinaus wird es mit Netzwerkvirtualisierung m{\"o}glich das physikalische Netz so weit zu abstrahieren, dass die aktuell fest verzahnten Rollen von Netzwerkbesitzer und Netzwerkbetreiber entkoppelt werden k{\"o}nnen. Dar{\"u}ber hinaus stellt Netzwerkvirtualisierung sicher, dass unterschiedliche Datennetze, die gleichzeitig auf dem gleichen physikalischen Netz betrieben werden, sich gegenseitig weder beeinflussen noch st{\"o}ren k{\"o}nnen. Diese Arbeit  besch{\"a}ftigt sich mit ausgew{\"a}hlten Aspekten dieses Themenkomplexes und fokussiert sich darauf, ein virtuelles Netzwerk mit bestm{\"o}glicher Dienstqualit{\"a}t f{\"u}r den Nutzer zu betreiben und zu steuern. Daf{\"u}r wird ein Top-down-Ansatz gew{\"a}hlt, der von den Anwendungsf{\"a}llen, einer m{\"o}glichen Netzwerkvirtualisierungs-Architektur und aktuellen M{\"o}glichkeiten der Hardwarevirtualisierung ausgeht. Im Weiteren fokussiert sich die Arbeit dann in Richtung Bestimmung und Optimierung der vom Nutzer erfahrenen Dienstqualit{\"a}t (QoE) auf Applikationsschicht und diskutiert M{\"o}glichkeiten zur Messung und {\"U}berwachung von wesentlichen Netzparametern in virtualisierten Netzen.}, subject = {Netzwerkmanagement}, language = {en} } @phdthesis{Selbach2011, author = {Selbach, Stefan}, title = {Hybride bitparallele Volltextsuche}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-66476}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2011}, abstract = {Der große Vorteil eines q-Gramm Indexes liegt darin, dass es m{\"o}glich ist beliebige Zeichenketten in einer Dokumentensammlung zu suchen. Ein Nachteil jedoch liegt darin, dass bei gr{\"o}ßer werdenden Datenmengen dieser Index dazu neigt, sehr groß zu werden, was mit einem deutlichem Leistungsabfall verbunden ist. In dieser Arbeit wird eine neuartige Technik vorgestellt, die die Leistung eines q-Gramm Indexes mithilfe zus{\"a}tzlicher M-Matrizen f{\"u}r jedes q-Gramm und durch die Kombination mit einem invertierten Index erh{\"o}ht. Eine M-Matrix ist eine Bit-Matrix, die Informationen {\"u}ber die Positionen eines q-Gramms enth{\"a}lt. Auch bei der Kombination von zwei oder mehreren Q-Grammen bieten diese M-Matrizen Informationen {\"u}ber die Positionen der Kombination. Dies kann verwendet werden, um die Komplexit{\"a}t der Zusammenf{\"u}hrung der q-Gramm Trefferlisten f{\"u}r eine gegebene Suchanfrage zu reduzieren und verbessert die Leistung des n-Gramm-invertierten Index. Die Kombination mit einem termbasierten invertierten Index beschleunigt die durchschnittliche Suchzeit zus{\"a}tzlich und vereint die Vorteile beider Index-Formate. Redundante Informationen werden in dem q-Gramm Index reduziert und weitere Funktionalit{\"a}t hinzugef{\"u}gt, wie z.B. die Bewertung von Treffern nach Relevanz, die M{\"o}glichkeit, nach Konzepten zu suchen oder Indexpartitionierungen nach Wichtigkeit der enthaltenen Terme zu erstellen.}, subject = {Information Retrieval}, language = {de} } @phdthesis{Duelli2012, author = {Duelli, Michael}, title = {Heuristic Design and Provisioning of Resilient Multi-Layer Networks}, doi = {10.25972/OPUS-5600}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-69433}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2012}, abstract = {To jointly provide different services/technologies, like IP and Ethernet or IP and SDH/SONET, in a single network, equipment of multiple technologies needs to be deployed to the sites/Points of Presence (PoP) and interconnected with each other. Therein, a technology may provide transport functionality to other technologies and increase the number of available resources by using multiplexing techniques. By providing its own switching functionality, each technology creates connections in a logical layer which leads to the notion of multi-layer networks. The design of such networks comprises the deployment and interconnection of components to suit to given traffic demands. To prevent traffic loss due to failures of networking equipment, protection mechanisms need to be established. In multi-layer networks, protection usually can be applied in any of the considered layers. In turn, the hierarchical structure of multi-layer networks also bears shared risk groups (SRG). To achieve a cost-optimal resilient network, an appropriate combination of multiplexing techniques, technologies, and their interconnections needs to be found. Thus, network design is a combinatorial problem with a large parameter and solution space. After the design stage, the resources of a multi-layer network can be provided to traffic demands. Especially, dynamic capacity provisioning requires interaction of sites and layers, as well as accurate retrieval of constraint information. In recent years, generalized multiprotocol label switching (GMPLS) and path computation elements (PCE) have emerged as possible approaches for these challenges. Like the design, the provisioning of multi-layer networks comprises a variety of optimization parameters, like blocking probability, resilience, and energy efficiency. In this work, we introduce several efficient heuristics to approach the considered optimization problems. We perform capital expenditure (CAPEX)-aware design of multi-layer networks from scratch, based on IST NOBEL phase 2 project's cost and equipment data. We comprise traffic and resilience requirements in different and multiple layers as well as different network architectures. On top of the designed networks, we consider the dynamic provisioning of multi-layer traffic based on the GMPLS and PCE architecture. We evaluate different PCE deployments, information retrieval strategies, and re-optimization. Finally, we show how information about provisioning utilization can be used to provide a feedback for network design.}, subject = {Mehrschichtsystem}, language = {en} } @phdthesis{Saska2009, author = {Saska, Martin}, title = {Trajectory planning and optimal control for formations of autonomous robots}, isbn = {978-3-923959-56-3}, doi = {10.25972/OPUS-4622}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-53175}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2009}, abstract = {In this thesis, we present novel approaches for formation driving of nonholonomic robots and optimal trajectory planning to reach a target region. The methods consider a static known map of the environment as well as unknown and dynamic obstacles detected by sensors of the formation. The algorithms are based on leader following techniques, where the formation of car-like robots is maintained in a shape determined by curvilinear coordinates. Beyond this, the general methods of formation driving are specialized and extended for an application of airport snow shoveling. Detailed descriptions of the algorithms complemented by relevant stability and convergence studies will be provided in the following chapters. Furthermore, discussions of the applicability will be verified by various simulations in existing robotic environments and also by a hardware experiment.}, subject = {Autonomer Roboter}, language = {en} } @phdthesis{Fehler2010, author = {Fehler, Manuel}, title = {Kalibrierung Agenten-basierter Simulationen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-64762}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2010}, abstract = {In der vorliegenden Arbeit wird das Problem der Kalibrierung Agenten-basierter Simulationen (ABS) behandelt, also das Problem, die Parameterwerte eines Agenten-basierten Simulationsmodells so einzustellen, dass valides Simulationsverhalten erreicht wird. Das Kalibrierungsproblem f{\"u}r Simulationen an sich ist nicht neu und ist im Rahmen klassischer Simulationsparadigmen, wie z.B. der Makro-Simulation, fester Bestandteil der Forschung. Im Vergleich zu den dort betrachteten Kalibrierungsproblemen zeichnet sich das Kalibrierungsproblem f{\"u}r ABS jedoch durch eine Reihe zus{\"a}tzlicher Herausforderungen aus, welche die direkte Anwendung existierender Kalibrierungsverfahren in begrenzter Zeit erschweren, bzw. nicht mehr sinnvoll zulassen. Die L{\"o}sung dieser Probleme steht im Zentrum dieser Dissertation: Das Ziel besteht darin, den Nutzer bei der Kalibrierung von ABS auf der Basis von unzureichenden, potentiell fehlerhaften Daten und Wissen zu unterst{\"u}tzen. Dabei sollen drei Hauptprobleme gel{\"o}st werden: 1)Vereinfachung der Kalibrierung großer Agenten-Parametermengen auf der Mikro- Ebene in Agenten-basierten Simulationen durch Ausnutzung der spezifischen Struktur von ABS (n{\"a}mlich dem Aufbau aus einer Menge von Agentenmodellen). 2)Kalibrierung Agenten-basierter Simulationen, so dass auf allen relevanten Beobachtungsebenen valides Simulationsverhalten erzeugt wird (mindestens Mikro und Makro-Ebene). Als erschwerende Randbedingung muss die Kalibrierung unter der Voraussetzung einer Makro-Mikro-Wissensl{\"u}cke durchgef{\"u}hrt werden. 3)Kalibrierung Agenten-basierter Simulationen auf der Mikro-Ebene unter der Voraussetzung, dass zur Kalibrierung einzelner Agentenmodelle nicht ausreichend und potentiell verf{\"a}lschte Daten zur Verhaltensvalidierung zur Verf{\"u}gung stehen. Hierzu wird in dieser Arbeit das sogenannte Makro-Mikro-Verfahren zur Kalibrierung von Agenten-basierten Simulationen entwickelt. Das Verfahren besteht aus einem Basisverfahren, das im Verlauf der Arbeit um verschiedene Zusatzverfahren erweitert wird. Das Makro-Mikro-Verfahren und seine Erweiterungen sollen dazu dienen, die Modellkalibrierung trotz stark verrauschter Daten und eingeschr{\"a}nktem Wissen {\"u}ber die Wirkungszusammenh{\"a}nge im Originalsystem geeignet zu erm{\"o}glichen und dabei den Kalibrierungsprozess zu beschleunigen: 1) Makro-Mikro-Kalibrierungsverfahren: Das in dieser Arbeit entwickelte Makro- Mikro-Verfahren unterst{\"u}tzt den Nutzer durch eine kombinierte Kalibrierung auf der Mikro- und der Makro-Beobachtungsebene, die gegebenenfalls durch Zwischenebenen erweitert werden kann. Der Grundgedanke des Verfahrens besteht darin, das Kalibrierungsproblem in eines auf aggregierter Verhaltensebene und eines auf der Ebene des Mikro-Agentenverhaltens aufzuteilen. Auf der Makro-Ebene wird nach validen idealen aggregierten Verhaltensmodellen (IVM) der Agenten gesucht. Auf der Mikro-Ebene wird versucht die individuellen Modelle der Agenten auf Basis des erw{\"u}nschten Gesamtverhaltens und der ermittelten IVM so zu kalibrieren, das insgesamt Simulationsverhalten entsteht, das sowohl auf Mikro- als auch auf Makro-Ebene valide ist. 2) Erweiterung 1: Robuste Kalibrierung: Um den Umgang mit potentiell verrauschten Validierungskriterien (d.h. mit verrauschten Daten {\"u}ber ein Originalsystem, auf denen die Validierungskriterien der Simulation beruhen) und Modellteilen w{\"a}hrend der Kalibrierung von ABS zu erm{\"o}glichen, wird eine robuste Kalibrierungstechnik zur Anwendung im Makro-Mikro-Verfahren entwickelt. 3) Erweiterung 2: Kalibrierung mit Heterogenit{\"a}tssuche: Als zweite Erweiterung des Makro-Mikro-Verfahrens wird ein Verfahren entwickelt, das das Problem des unklaren Detaillierungsgrades von ABS auf der Ebene der Parameterwerte adressiert. Prinzipiell kann zwar jeder Agent unterschiedliche Parameterwerte verwenden, obwohl eine geringere Heterogenit{\"a}t zur Erzeugung validen Verhaltens ausreichend w{\"a}re. Die entwickelte Erweiterung versucht, w{\"a}hrend der Kalibrierung, eine geeignete Heterogenit{\"a}tsauspr{\"a}gung f{\"u}r die Parameterwerte der Agenten zu ermitteln. Unter einer Heterogenit{\"a}tsauspr{\"a}gung wird dabei eine Einteilung der simulierten Agenten in Gruppen mit jeweils gleichen Parameterwerten verstanden. Die Heterogenit{\"a}tssuche dient dazu, einen Kompromiss zu finden zwischen der Notwendigkeit, sehr große Parametersuchr{\"a}ume durchsuchen zu m{\"u}ssen und gleichzeitig den Suchraum so klein wie m{\"o}glich halten zu wollen.}, subject = {Computersimulation}, language = {de} } @phdthesis{Sun2014, author = {Sun, Kaipeng}, title = {Six Degrees of Freedom Object Pose Estimation with Fusion Data from a Time-of-flight Camera and a Color Camera}, isbn = {978-3-923959-97-6}, doi = {10.25972/OPUS-10508}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-105089}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {Object six Degrees of Freedom (6DOF) pose estimation is a fundamental problem in many practical robotic applications, where the target or an obstacle with a simple or complex shape can move fast in cluttered environments. In this thesis, a 6DOF pose estimation algorithm is developed based on the fused data from a time-of-flight camera and a color camera. The algorithm is divided into two stages, an annealed particle filter based coarse pose estimation stage and a gradient decent based accurate pose optimization stage. In the first stage, each particle is evaluated with sparse representation. In this stage, the large inter-frame motion of the target can be well handled. In the second stage, the range data based conventional Iterative Closest Point is extended by incorporating the target appearance information and used for calculating the accurate pose by refining the coarse estimate from the first stage. For dealing with significant illumination variations during the tracking, spherical harmonic illumination modeling is investigated and integrated into both stages. The robustness and accuracy of the proposed algorithm are demonstrated through experiments on various objects in both indoor and outdoor environments. Moreover, real-time performance can be achieved with graphics processing unit acceleration.}, subject = {Mustererkennung}, language = {en} } @phdthesis{Kindermann2016, author = {Kindermann, Philipp}, title = {Angular Schematization in Graph Drawing}, publisher = {W{\"u}rzburg University Press}, address = {W{\"u}rzburg}, isbn = {978-3-95826-020-7 (print)}, doi = {10.25972/WUP-978-3-95826-021-4}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-112549}, school = {W{\"u}rzburg University Press}, pages = {184}, year = {2016}, abstract = {Graphs are a frequently used tool to model relationships among entities. A graph is a binary relation between objects, that is, it consists of a set of objects (vertices) and a set of pairs of objects (edges). Networks are common examples of modeling data as a graph. For example, relationships between persons in a social network, or network links between computers in a telecommunication network can be represented by a graph. The clearest way to illustrate the modeled data is to visualize the graphs. The field of Graph Drawing deals with the problem of finding algorithms to automatically generate graph visualizations. The task is to find a "good" drawing, which can be measured by different criteria such as number of crossings between edges or the used area. In this thesis, we study Angular Schematization in Graph Drawing. By this, we mean drawings with large angles (for example, between the edges at common vertices or at crossing points). The thesis consists of three parts. First, we deal with the placement of boxes. Boxes are axis-parallel rectangles that can, for example, contain text. They can be placed on a map to label important sites, or can be used to describe semantic relationships between words in a word network. In the second part of the thesis, we consider graph drawings visually guide the viewer. These drawings generally induce large angles between edges that meet at a vertex. Furthermore, the edges are drawn crossing-free and in a way that makes them easy to follow for the human eye. The third and final part is devoted to crossings with large angles. In drawings with crossings, it is important to have large angles between edges at their crossing point, preferably right angles.}, language = {en} } @techreport{KounevBrosigHuber2014, author = {Kounev, Samuel and Brosig, Fabian and Huber, Nikolaus}, title = {The Descartes Modeling Language}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-104887}, pages = {91}, year = {2014}, abstract = {This technical report introduces the Descartes Modeling Language (DML), a new architecture-level modeling language for modeling Quality-of-Service (QoS) and resource management related aspects of modern dynamic IT systems, infrastructures and services. DML is designed to serve as a basis for self-aware resource management during operation ensuring that system QoS requirements are continuously satisfied while infrastructure resources are utilized as efficiently as possible.}, subject = {Ressourcenmanagement}, language = {en} } @article{BeckerCaminitiFiorellaetal.2013, author = {Becker, Martin and Caminiti, Saverio and Fiorella, Donato and Francis, Louise and Gravino, Pietro and Haklay, Mordechai (Muki) and Hotho, Andreas and Loreto, Virrorio and Mueller, Juergen and Ricchiuti, Ferdinando and Servedio, Vito D. P. and Sirbu, Alina and Tria, Franesca}, title = {Awareness and Learning in Participatory Noise Sensing}, series = {PLOS ONE}, volume = {8}, journal = {PLOS ONE}, number = {12}, issn = {1932-6203}, doi = {10.1371/journal.pone.0081638}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-127675}, pages = {e81638}, year = {2013}, abstract = {The development of ICT infrastructures has facilitated the emergence of new paradigms for looking at society and the environment over the last few years. Participatory environmental sensing, i.e. directly involving citizens in environmental monitoring, is one example, which is hoped to encourage learning and enhance awareness of environmental issues. In this paper, an analysis of the behaviour of individuals involved in noise sensing is presented. Citizens have been involved in noise measuring activities through the WideNoise smartphone application. This application has been designed to record both objective (noise samples) and subjective (opinions, feelings) data. The application has been open to be used freely by anyone and has been widely employed worldwide. In addition, several test cases have been organised in European countries. Based on the information submitted by users, an analysis of emerging awareness and learning is performed. The data show that changes in the way the environment is perceived after repeated usage of the application do appear. Specifically, users learn how to recognise different noise levels they are exposed to. Additionally, the subjective data collected indicate an increased user involvement in time and a categorisation effect between pleasant and less pleasant environments.}, language = {en} } @article{BuchinBuchinByrkaetal.2012, author = {Buchin, Kevin and Buchin, Maike and Byrka, Jaroslaw and N{\"o}llenburg, Martin and Okamoto, Yoshio and Silveira, Rodrigo I. and Wolff, Alexander}, title = {Drawing (Complete) Binary Tanglegrams}, series = {Algorithmica}, volume = {62}, journal = {Algorithmica}, doi = {10.1007/s00453-010-9456-3}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-124622}, pages = {309-332}, year = {2012}, abstract = {A binary tanglegram is a drawing of a pair of rooted binary trees whose leaf sets are in one-to-one correspondence; matching leaves are connected by inter-tree edges. For applications, for example, in phylogenetics, it is essential that both trees are drawn without edge crossings and that the inter-tree edges have as few crossings as possible. It is known that finding a tanglegram with the minimum number of crossings is NP-hard and that the problem is fixed-parameter tractable with respect to that number. We prove that under the Unique Games Conjecture there is no constant-factor approximation for binary trees. We show that the problem is NP-hard even if both trees are complete binary trees. For this case we give an O(n 3)-time 2-approximation and a new, simple fixed-parameter algorithm. We show that the maximization version of the dual problem for binary trees can be reduced to a version of MaxCut for which the algorithm of Goemans and Williamson yields a 0.878-approximation.}, language = {en} } @article{ToepferCorovicFetteetal.2015, author = {Toepfer, Martin and Corovic, Hamo and Fette, Georg and Kl{\"u}gl, Peter and St{\"o}rk, Stefan and Puppe, Frank}, title = {Fine-grained information extraction from German transthoracic echocardiography reports}, series = {BMC Medical Informatics and Decision Making}, volume = {15}, journal = {BMC Medical Informatics and Decision Making}, number = {91}, doi = {doi:10.1186/s12911-015-0215-x}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-125509}, year = {2015}, abstract = {Background Information extraction techniques that get structured representations out of unstructured data make a large amount of clinically relevant information about patients accessible for semantic applications. These methods typically rely on standardized terminologies that guide this process. Many languages and clinical domains, however, lack appropriate resources and tools, as well as evaluations of their applications, especially if detailed conceptualizations of the domain are required. For instance, German transthoracic echocardiography reports have not been targeted sufficiently before, despite of their importance for clinical trials. This work therefore aimed at development and evaluation of an information extraction component with a fine-grained terminology that enables to recognize almost all relevant information stated in German transthoracic echocardiography reports at the University Hospital of W{\"u}rzburg. Methods A domain expert validated and iteratively refined an automatically inferred base terminology. The terminology was used by an ontology-driven information extraction system that outputs attribute value pairs. The final component has been mapped to the central elements of a standardized terminology, and it has been evaluated according to documents with different layouts. Results The final system achieved state-of-the-art precision (micro average.996) and recall (micro average.961) on 100 test documents that represent more than 90 \% of all reports. In particular, principal aspects as defined in a standardized external terminology were recognized with f 1=.989 (micro average) and f 1=.963 (macro average). As a result of keyword matching and restraint concept extraction, the system obtained high precision also on unstructured or exceptionally short documents, and documents with uncommon layout. Conclusions The developed terminology and the proposed information extraction system allow to extract fine-grained information from German semi-structured transthoracic echocardiography reports with very high precision and high recall on the majority of documents at the University Hospital of W{\"u}rzburg. Extracted results populate a clinical data warehouse which supports clinical research.}, language = {en} } @phdthesis{Hopfner2008, author = {Hopfner, Marbod}, title = {Source Code Analysis, Management, and Visualization for PROLOG}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-36300}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2008}, abstract = {This thesis deals with the management and analysis of source code, which is represented in XML. Using the elementary methods of the XML repository, the XML source code representation is accessed, changed, updated, and saved. We reason about the source code, refactor source code and we visualize dependency graphs for call analysis. The visualized dependencies between files, modules, or packages are used to structure the source code in order to get a system, which is easily to comprehend, to modify and to complete. Sophisticated methods have been developed to slice the source code in order to obtain a working package of a large system, containing only a specific functionality. The basic methods, on which the visualizations and analyses are built on can be changed like changing a plug-in. The visualization methods can be reused in order to handle arbitrary source code representations, e.g., JAML, PHPML, PROLOGML. Dependencies of other context can be visualized, too, e.g., ER diagrams, or website references. The tool SCAV supports source code visualization and analyzing methods.}, subject = {Refactoring}, language = {en} } @phdthesis{Binder2006, author = {Binder, Andreas}, title = {Die stochastische Wissenschaft und zwei Teilsysteme eines Web-basierten Informations- und Anwendungssystems zu ihrer Etablierung}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-26146}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2006}, abstract = {Das stochastische Denken, die Bernoullische Stochastik und dessen informationstechnologische Umsetzung, namens Stochastikon stellen die Grundlage f{\"u}r das Verst{\"a}ndnis und die erfolgreiche Nutzung einer stochastischen Wissenschaft dar. Im Rahmen dieser Arbeit erfolgt eine Kl{\"a}rung des Begriffs des stochastischen Denkens, eine anschauliche Darstellung der von Elart von Collani entwickelten Bernoullischen Stochastik und eine Beschreibung von Stochastikon. Dabei werden sowohl das Gesamtkonzept von Stochastikon, sowie die Ziele, Aufgaben und die Realisierung der beiden Teilsysteme namens Mentor und Encyclopedia vorgestellt. Das stochastische Denken erlaubt eine realit{\"a}tsnahe Sichtweise der Dinge, d.h. eine Sichtweise, die mit den menschlichen Beobachtungen und Erfahrungen im Einklang steht und somit die Unsicherheit {\"u}ber zuk{\"u}nftige Entwicklungen ber{\"u}cksichtigt. Der in diesem Kontext verwendete Begriff der Unsicherheit bezieht sich ausschließlich auf zuk{\"u}nftige Entwicklungen und {\"a}ußert sich in Variabilit{\"a}t. Quellen der Unsicherheit sind einerseits die menschliche Ignoranz und andererseits der Zufall. Unter Ignoranz wird hierbei die Unwissenheit des Menschen {\"u}ber die unbekannten, aber feststehenden Fakten verstanden, die die Anfangsbedingungen der zuk{\"u}nftigen Entwicklung repr{\"a}sentieren. Die Bernoullische Stochastik liefert ein Regelwerk und erm{\"o}glicht die Entwicklung eines quantitativen Modells zur Beschreibung der Unsicherheit und expliziter Einbeziehung der beiden Quellen Ignoranz und Zufall. Das Modell tr{\"a}gt den Namen Bernoulli-Raum und bildet die Grundlage f{\"u}r die Herleitung quantitativer Verfahren, um zuverl{\"a}ssige und genaue Aussagen sowohl {\"u}ber die nicht-existente zuf{\"a}llige Zukunft (Vorhersageverfahren), als auch {\"u}ber die unbekannte feststehende Vergangenheit (Messverfahren). Das Softwaresystem Stochastikon implementiert die Bernoullische Stochastik in Form einer Reihe autarker, miteinander kommunizierender Teilsysteme. Ziel des Teilsystems Encyclopedia ist die Bereitstellung und Bewertung stochastischen Wissens. Das Teilsystem Mentor dient der Unterst{\"u}tzung des Anwenders bei der Probleml{\"o}sungsfindung durch Identifikation eines richtigen Modells bzw. eines korrekten Bernoulli-Raums. Der L{\"o}sungsfindungsprozess selber enth{\"a}lt keinerlei Unsicherheit. Die ganze Unsicherheit steckt in der L{\"o}sung, d.h. im Bernoulli-Raum, der explizit die vorhandene Unwissenheit (Ignoranz) und den vorliegenden Zufall abdeckend enth{\"a}lt.}, subject = {Stochastik}, language = {de} } @phdthesis{Binzenhoefer2007, author = {Binzenh{\"o}fer, Andreas}, title = {Performance Analysis of Structured Overlay Networks}, doi = {10.25972/OPUS-2250}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-26291}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2007}, abstract = {Overlay networks establish logical connections between users on top of the physical network. While randomly connected overlay networks provide only a best effort service, a new generation of structured overlay systems based on Distributed Hash Tables (DHTs) was proposed by the research community. However, there is still a lack of understanding the performance of such DHTs. Additionally, those architectures are highly distributed and therefore appear as a black box to the operator. Yet an operator does not want to lose control over his system and needs to be able to continuously observe and examine its current state at runtime. This work addresses both problems and shows how the solutions can be combined into a more self-organizing overlay concept. At first, we evaluate the performance of structured overlay networks under different aspects and thereby illuminate in how far such architectures are able to support carrier-grade applications. Secondly, to enable operators to monitor and understand their deployed system in more detail, we introduce both active as well as passive methods to gather information about the current state of the overlay network.}, subject = {Overlay-Netz}, language = {en} } @phdthesis{Pries2010, author = {Pries, Jan Rastin}, title = {Performance Optimization of Wireless Infrastructure and Mesh Networks}, doi = {10.25972/OPUS-3723}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-46097}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2010}, abstract = {Future broadband wireless networks should be able to support not only best effort traffic but also real-time traffic with strict Quality of Service (QoS) constraints. In addition, their available resources are scare and limit the number of users. To facilitate QoS guarantees and increase the maximum number of concurrent users, wireless networks require careful planning and optimization. In this monograph, we studied three aspects of performance optimization in wireless networks: resource optimization in WLAN infrastructure networks, quality of experience control in wireless mesh networks, and planning and optimization of wireless mesh networks. An adaptive resource management system is required to effectively utilize the limited resources on the air interface and to guarantee QoS for real-time applications. Thereby, both WLAN infrastructure and WLAN mesh networks have to be considered. An a-priori setting of the access parameters is not meaningful due to the contention-based medium access and the high dynamics of the system. Thus, a management system is required which dynamically adjusts the channel access parameters based on the network load. While this is sufficient for wireless infrastructure networks, interferences on neighboring paths and self-interferences have to be considered for wireless mesh networks. In addition, a careful channel allocation and route assignment is needed. Due to the large parameter space, standard optimization techniques fail for optimizing large wireless mesh networks. In this monograph, we reveal that biology-inspired optimization techniques, namely genetic algorithms, are well-suitable for the planning and optimization of wireless mesh networks. Although genetic algorithms generally do not always find the optimal solution, we show that with a good parameter set for the genetic algorithm, the overall throughput of the wireless mesh network can be significantly improved while still sharing the resources fairly among the users.}, subject = {IEEE 802.11}, language = {en} } @inproceedings{EppleeLangbehn2021, author = {Eppl{\´e}e, Rafael and Langbehn, Eike}, title = {Overlapping Architecture: Implementation of Impossible Spaces in Virtual Reality Games}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-246045}, pages = {37-46}, year = {2021}, abstract = {Natural walking in virtual reality games is constrained by the physical boundaries defined by the size of the player's tracking space. Impossible spaces, a redirected walking technique, enlarge the virtual environment by creating overlapping architecture and letting multiple locations occupy the same physical space. Within certain thresholds, this is subtle to the player. In this paper, we present our approach to implement such impossible spaces and describe how we handled challenges like objects with simulated physics or precomputed global illumination.}, language = {en} } @phdthesis{Busch2016, author = {Busch, Stephan}, title = {Robust, Flexible and Efficient Design for Miniature Satellite Systems}, isbn = {978-3-945459-10-2}, doi = {10.25972/OPUS-13652}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-136523}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2016}, abstract = {Small satellites contribute significantly in the rapidly evolving innovation in space engineering, in particular in distributed space systems for global Earth observation and communication services. Significant mass reduction by miniaturization, increased utilization of commercial high-tech components, and in particular standardization are the key drivers for modern miniature space technology. This thesis addresses key fields in research and development on miniature satellite technology regarding efficiency, flexibility, and robustness. Here, these challenges are addressed by the University of Wuerzburg's advanced pico-satellite bus, realizing a generic modular satellite architecture and standardized interfaces for all subsystems. The modular platform ensures reusability, scalability, and increased testability due to its flexible subsystem interface which allows efficient and compact integration of the entire satellite in a plug-and-play manner. Beside systematic design for testability, a high degree of operational robustness is achieved by the consequent implementation of redundancy of crucial subsystems. This is combined with efficient fault detection, isolation and recovery mechanisms. Thus, the UWE-3 platform, and in particular the on-board data handling system and the electrical power system, offers one of the most efficient pico-satellite architectures launched in recent years and provides a solid basis for future extensions. The in-orbit performance results of the pico-satellite UWE-3 are presented and summarize successful operations since its launch in 2013. Several software extensions and adaptations have been uploaded to UWE-3 increasing its capabilities. Thus, a very flexible platform for in-orbit software experiments and for evaluations of innovative concepts was provided and tested.}, subject = {Kleinsatellit}, language = {en} } @article{MandelHoernleinIflandetal.2011, author = {Mandel, Alexander and H{\"o}rnlein, Alexander and Ifland, Marianus and L{\"u}neburg, Edeltraud and Deckert, J{\"u}rgen and Puppe, Frank}, title = {Aufwandsanalyse f{\"u}r computerunterst{\"u}tzte Multiple-Choice Papierklausuren}, series = {GMS Journal for Medical Education}, volume = {28}, journal = {GMS Journal for Medical Education}, number = {4}, doi = {10.3205/zma000767}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-134386}, pages = {1-15, Doc55}, year = {2011}, abstract = {Introduction: Multiple-choice-examinations are still fundamental for assessment in medical degree programs. In addition to content related research, the optimization of the technical procedure is an important question. Medical examiners face three options: paper-based examinations with or without computer support or completely electronic examinations. Critical aspects are the effort for formatting, the logistic effort during the actual examination, quality, promptness and effort of the correction, the time for making the documents available for inspection by the students, and the statistical analysis of the examination results. Methods: Since three semesters a computer program for input and formatting of MC-questions in medical and other paper-based examinations is used and continuously improved at Wuerzburg University. In the winter semester (WS) 2009/10 eleven, in the summer semester (SS) 2010 twelve and in WS 2010/11 thirteen medical examinations were accomplished with the program and automatically evaluated. For the last two semesters the remaining manual workload was recorded. Results: The cost of the formatting and the subsequent analysis including adjustments of the analysis of an average examination with about 140 participants and about 35 questions was 5-7 hours for exams without complications in the winter semester 2009/2010, about 2 hours in SS 2010 and about 1.5 hours in the winter semester 2010/11. Including exams with complications, the average time was about 3 hours per exam in SS 2010 and 2.67 hours for the WS 10/11. Discussion: For conventional multiple-choice exams the computer-based formatting and evaluation of paper-based exams offers a significant time reduction for lecturers in comparison with the manual correction of paper-based exams and compared to purely electronically conducted exams it needs a much simpler technological infrastructure and fewer staff during the exam."}, language = {de} } @article{BoehlerCreignouGalotaetal.2012, author = {B{\"o}hler, Elmar and Creignou, Nadia and Galota, Matthias and Reith, Steffen and Schnoor, Henning and Vollmer, Heribert}, title = {Complexity Classifications for Different Equivalence and Audit Problems for Boolean Circuits}, series = {Logical Methods in Computer Science}, volume = {8}, journal = {Logical Methods in Computer Science}, number = {3:27}, doi = {10.2168/LMCS-8(3:27)2012}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-131121}, pages = {1 -- 25}, year = {2012}, abstract = {We study Boolean circuits as a representation of Boolean functions and conskier different equivalence, audit, and enumeration problems. For a number of restricted sets of gate types (bases) we obtain efficient algorithms, while for all other gate types we show these problems are at least NP-hard.}, language = {en} } @phdthesis{Herrler2007, author = {Herrler, Rainer}, title = {Agentenbasierte Simulation zur Ablaufoptimierung in Krankenh{\"a}usern und anderen verteilten, dynamischen Umgebungen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-24483}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2007}, abstract = {Verteilte dynamische Systeme unter lokalen und globalen Gesichtspunkten zu optimieren ist eine schwierige Aufgabe. Zwar sind grunds{\"a}tzliche Auswirkungen einzelner Maßnahmen h{\"a}ufig bekannt, durch widerstrebende Ziele, Wechselwirkungen zwischen Prozessen und Nebenwirkungen von Maßnahmen ist ein analytisches Vorgehen bei der Optimierung nicht m{\"o}glich. Besonders schwierig wird es, wenn lokale Einheiten einerseits ihre Ziele und Autonomie behalten sollen, aber durch zentrale Vorgaben bzw. Anreize so gesteuert werden sollen, dass ein {\"u}bergeordnetes Ziel erreicht wird. Ein praktisches Beispiel dieses allgemeinen Optimierungsproblems findet sich im Gesundheitswesen. Das Management von modernen Kliniken ist stets mit dem Problem konfrontiert, die Qualit{\"a}t der Pflege zu gew{\"a}hrleisten und gleichzeitig kosteneffizient zu arbeiten. Hier gilt es unter gegeben Rahmenbedingungen und bei Respektierung der Autonomie der Funktionseinheiten, Optimierungsmaßnahmen zu finden und durchzuf{\"u}hren. Vorhandene Werkzeuge zur Simulation und Modellierung bieten f{\"u}r diese Aufgabe keine ausreichend guten Vorgehensmodelle und Modellierungsmechanismen. Die agentenbasierte Simulation erm{\"o}glicht die Abbildung solcher Systeme und die Durchf{\"u}hrung von Simulationsexperimenten zur Bewertung einzelner Maßnahmen. Es werden L{\"o}sungswege und Werkzeuge vorgestellt und evaluiert, die den Benutzer bei der Formalisierung des Wissens und der Modellierung solch komplexer Szenarien unterst{\"u}tzen und ein systematisches Vorgehen zur Optimierung erm{\"o}glichen.}, subject = {Simulation}, language = {de} } @misc{Hoehn2006, type = {Master Thesis}, author = {H{\"o}hn, Winfried}, title = {Mustererkennung in Fr{\"u}hdrucken}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-30429}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2006}, abstract = {No abstract available}, subject = {Mustererkennung}, language = {de} } @phdthesis{Hossfeld2009, author = {Hoßfeld, Tobias}, title = {Performance Evaluation of Future Internet Applications and Emerging User Behavior}, doi = {10.25972/OPUS-3067}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-37570}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2009}, abstract = {In future telecommunication systems, we observe an increasing diversity of access networks. The separation of transport services and applications or services leads to multi-network services, i.e., a future service has to work transparently to the underlying network infrastructure. Multi-network services with edge-based intelligence, like P2P file sharing or the Skype VoIP service, impose new traffic control paradigms on the future Internet. Such services adapt the amount of consumed bandwidth to reach different goals. A selfish behavior tries to keep the QoE of a single user above a certain level. Skype, for instance, repeats voice samples depending on the perceived end-to-end loss. From the viewpoint of a single user, the replication of voice data overcomes the degradation caused by packet loss and enables to maintain a certain QoE. The cost for this achievement is a higher amount of consumed bandwidth. However, if the packet loss is caused by congestion in the network, this additionally required bandwidth even worsens the network situation. Altruistic behavior, on the other side, would reduce the bandwidth consumption in such a way that the pressure on the network is released and thus the overall network performance is improved. In this monograph, we analyzed the impact of the overlay, P2P, and QoE paradigms in future Internet applications and the interactions from the observing user behavior. The shift of intelligence toward the edge is accompanied by a change in the emerging user behavior and traffic profile, as well as a change from multi-service networks to multi-networks services. In addition, edge-based intelligence may lead to a higher dynamics in the network topology, since the applications are often controlled by an overlay network, which can rapidly change in size and structure as new nodes can leave or join the overlay network in an entirely distributed manner. As a result, we found that the performance evaluation of such services provides new challenges, since novel key performance factors have to be first identified, like pollution of P2P systems, and appropriate models of the emerging user behavior are required, e.g. taking into account user impatience. As common denominator of the presented studies in this work, we focus on a user-centric view when evaluating the performance of future Internet applications. For a subscriber of a certain application or service, the perceived quality expressed as QoE will be the major criterion of the user's satisfaction with the network and service providers. We selected three different case studies and characterized the application's performance from the end user's point of view. Those are (1) cooperation in mobile P2P file sharing networks, (2) modeling of online TV recording services, and (3) QoE of edge-based VoIP applications. The user-centric approach facilitates the development of new mechanisms to overcome problems arising from the changing user behavior. An example is the proposed CycPriM cooperation strategy, which copes with selfish user behavior in mobile P2P file sharing system. An adequate mechanism has also been shown to be efficient in a heterogeneous B3G network with mobile users conducting vertical handovers between different wireless access technologies. The consideration of the user behavior and the user perceived quality guides to an appropriate modeling of future Internet applications. In the case of the online TV recording service, this enables the comparison between different technical realizations of the system, e.g. using server clusters or P2P technology, to properly dimension the installed network elements and to assess the costs for service providers. Technologies like P2P help to overcome phenomena like flash crowds and improve scalability compared to server clusters, which may get overloaded in such situations. Nevertheless, P2P technology invokes additional challenges and different user behavior to that seen in traditional client/server systems. Beside the willingness to share files and the churn of users, peers may be malicious and offer fake contents to disturb the data dissemination. Finally, the understanding and the quantification of QoE with respect to QoS degradations permits designing sophisticated edge-based applications. To this end, we identified and formulated the IQX hypothesis as an exponential interdependency between QoE and QoS parameters, which we validated for different examples. The appropriate modeling of the emerging user behavior taking into account the user's perceived quality and its interactions with the overlay and P2P paradigm will finally help to design future Internet applications.}, subject = {Leistungsbewertung}, language = {en} } @inproceedings{AliMontenegro2015, author = {Ali, Qasim and Montenegro, Sergio}, title = {A Simple Approach to Quadrocopter Formation Flying Test Setup for Education and Development}, series = {INTED2015 Proceedings}, booktitle = {INTED2015 Proceedings}, publisher = {International Academy of Technology, Education and Development (IATED)}, isbn = {978-84-606-5763-7}, issn = {2340-1079}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-114495}, pages = {2776 -- 2784}, year = {2015}, abstract = {A simple test setup has been developed at Institute of Aerospace Information Technology, University of W{\"u}rzburg, Germany to realize basic functionalities for formation flight of quadrocopters. The test environment is planned to be utilized for developing and validating the algorithms for formation flying capability in real environment as well as for education purpose. An already existing test bed for single quadrocopter was extended with necessary inter-communication and distributed control mechanism to test the algorithms for formation flights in 2 degrees of freedom (roll / pitch). This study encompasses the domain of communication, control engineering and embedded systems programming. Bluetooth protocol has been used for inter-communication between two quadrocopters. A simple approach of PID control in combination with Kalman filter has been exploited. MATLAB Instrument Control Toolbox has been used for data display, plotting and analysis. Plots can be drawn in real-time and received information can also be stored in the form of files for later use and analysis. The test setup has been developed indigenously and at considerably low cost. Emphasis has been placed on simplicity to facilitate students learning process. Several lessons have been learnt during the course of development of this setup. Proposed setup is quite flexible that can be modified as per changing requirements.}, subject = {Flugk{\"o}rper}, language = {en} } @phdthesis{Hartmann2015, author = {Hartmann, Matthias}, title = {Optimization and Design of Network Architectures for Future Internet Routing}, issn = {1432-8801}, doi = {10.25972/OPUS-11416}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-114165}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {At the center of the Internet's protocol stack stands the Internet Protocol (IP) as a common denominator that enables all communication. To make routing efficient, resilient, and scalable, several aspects must be considered. Care must be taken that traffic is well balanced to make efficient use of the existing network resources, both in failure free operation and in failure scenarios. Finding the optimal routing in a network is an NP-complete problem. Therefore, routing optimization is usually performed using heuristics. This dissertation shows that a routing optimized with one objective function is often not good when looking at other objective functions. It can even be worse than unoptimized routing with respect to that objective function. After looking at failure-free routing and traffic distribution in different failure scenarios, the analysis is extended to include the loop-free alternate (LFA) IP fast reroute mechanism. Different application scenarios of LFAs are examined and a special focus is set on the fact that LFAs usually cannot protect all traffic in a network even against single link failures. Thus, the routing optimization for LFAs is targeted on both link utilization and failure coverage. Finally, the pre-congestion notification mechanism PCN for network admission control and overload protection is analyzed and optimized. Different design options for implementing the protocol are compared, before algorithms are developed for the calculation and optimization of protocol parameters and PCN-based routing. The second part of the thesis tackles a routing problem that can only be resolved on a global scale. The scalability of the Internet is at risk since a major and intensifying growth of the interdomain routing tables has been observed. Several protocols and architectures are analyzed that can be used to make interdomain routing more scalable. The most promising approach is the locator/identifier (Loc/ID) split architecture which separates routing from host identification. This way, changes in connectivity, mobility of end hosts, or traffic-engineering activities are hidden from the routing in the core of the Internet and the routing tables can be kept much smaller. All of the currently proposed Loc/ID split approaches have their downsides. In particular, the fact that most architectures use the ID for routing outside the Internet's core is a poor design, which inhibits many of the possible features of a new routing architecture. To better understand the problems and to provide a solution for a scalable routing design that implements a true Loc/ID split, the new GLI-Split protocol is developed in this thesis, which provides separation of global and local routing and uses an ID that is independent from any routing decisions. Besides GLI-Split, several other new routing architectures implementing Loc/ID split have been proposed for the Internet. Most of them assume that a mapping system is queried for EID-to-RLOC mappings by an intermediate node at the border of an edge network. When the mapping system is queried by an intermediate node, packets are already on their way towards their destination, and therefore, the mapping system must be fast, scalable, secure, resilient, and should be able to relay packets without locators to nodes that can forward them to the correct destination. The dissertation develops a classification for all proposed mapping system architectures and shows their similarities and differences. Finally, the fast two-level mapping system FIRMS is developed. It includes security and resilience features as well as a relay service for initial packets of a flow when intermediate nodes encounter a cache miss for the EID-to-RLOC mapping.}, subject = {Netzwerk}, language = {en} } @article{GageikStrohmeierMontenegro2013, author = {Gageik, Nils and Strohmeier, Michael and Montenegro, Sergio}, title = {Waypoint flight parameter comparison of an autonomous UAV}, series = {International Journal of Artificial Intelligence \& Applications (IJAIA)}, journal = {International Journal of Artificial Intelligence \& Applications (IJAIA)}, doi = {10.5121/ijaia.2013.4304}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-96833}, year = {2013}, abstract = {The present paper compares the effect of different waypoint parameters on the flight performance of a special autonomous indoor UAV (unmanned aerial vehicle) fusing ultrasonic, inertial, pressure and optical sensors for 3D positioning and controlling. The investigated parameters are the acceptance threshold for reaching a waypoint as well as the maximal waypoint step size or block size. The effect of these parameters on the flight time and accuracy of the flight path is investigated. Therefore the paper addresses how the acceptance threshold and step size influence the speed and accuracy of the autonomous flight and thus influence the performance of the presented autonomous quadrocopter under real indoor navigation circumstances. Furthermore the paper demonstrates a drawback of the standard potential field method for navigation of such autonomous quadrocopters and points to an improvement.}, language = {en} } @article{GageikStrohmeierMontenegro2013, author = {Gageik, Nils and Strohmeier, Michael and Montenegro, Sergio}, title = {An Autonomous UAV with an Optical Flow Sensor for Positioning and Navigation}, series = {International Journal of Advanced Robotic Systems}, journal = {International Journal of Advanced Robotic Systems}, doi = {10.5772/56813}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-96368}, year = {2013}, abstract = {A procedure to control all six DOF (degrees of freedom) of a UAV (unmanned aerial vehicle) without an external reference system and to enable fully autonomous flight is presented here. For 2D positioning the principle of optical flow is used. Together with the output of height estimation, fusing ultrasonic, infrared and inertial and pressure sensor data, the 3D position of the UAV can be computed, controlled and steered. All data processing is done on the UAV. An external computer with a pathway planning interface is for commanding purposes only. The presented system is part of the AQopterI8 project, which aims to develop an autonomous flying quadrocopter for indoor application. The focus of this paper is 2D positioning using an optical flow sensor. As a result of the performed evaluation, it can be concluded that for position hold, the standard deviation of the position error is 10cm and after landing the position error is about 30cm.}, language = {en} } @phdthesis{Herrmann2013, author = {Herrmann, Christian}, title = {Robotic Motion Compensation for Applications in Radiation Oncology}, isbn = {978-3-923959-88-4}, doi = {10.25972/OPUS-6727}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-79045}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2013}, abstract = {Aufgrund vieler Verbesserungen der Behandlungsmethoden im Laufe der letzten 60 Jahre, erlaubt die Strahlentherapie heutzutage pr{\"a}zise Behandlungen von statischen Tumoren. Jedoch birgt die Bestrahlung von sich bewegenden Tumoren noch große Herausforderungen in sich, da bewegliche Tumore oft den Behandlungsstrahl verlassen. Dabei reduziert sich die Strahlendosis im Tumor w{\"a}hrend sich diese im umliegenden gesunden Gewebe erh{\"o}ht. Diese Forschungsarbeit zielt darauf ab, die Grenzen der Strahlentherapie zu erweitern, um pr{\"a}zise Behandlungen von beweglichen Tumoren zu erm{\"o}glichen. Der Fokus der Arbeit liegt auf der Erstellung eines Echtzeitsystems zur aktiven Kompensation von Tumorbewegungen durch robotergest{\"u}tzte Methoden. W{\"a}hrend Behandlungen befinden sich Patienten auf einer Patientenliege, mit der statische Lagerungsfehler vor Beginn einer Behandlung korrigiert werden. Die in dieser Arbeit verwendete Patientenliege "HexaPOD" ist ein paralleler Manipulator mit sechs Freiheitsgraden, der große Lasten innerhalb eines eingeschr{\"a}nkten Arbeitsbereichs pr{\"a}zise positionieren kann. Obwohl der HexaPOD urspr{\"u}nglich nicht f{\"u}r dynamische Anwendungen konzipiert wurde, wird dieser f{\"u}r eine dauerhafte Bewegungskompensation eingesetzt, in dem Patienten so bewegt werden, dass Tumore pr{\"a}zise im Zentralstrahl w{\"a}hrend der Dauer einer gesamten Behandlung verbleiben. Um ein echtzeitf{\"a}higes Kompensationssystem auf Basis des HexaPODs zu realisieren, muss eine Reihe an Herausforderungen bew{\"a}ltigt werden. Echtzeitaspekte werden einerseits durch die Verwendung eines harten Echtzeitbetriebssystems abgedeckt, andererseits durch die Messung und Sch{\"a}tzung von Latenzzeiten aller physikalischen Gr{\"o}ßen im System, z.B. Messungen der Tumor- und Atemposition. Neben der konsistenten und durchg{\"a}ngigen Ber{\"u}cksichtigung von akkuraten Zeitinformation, werden alle software-induzierten Latenzen adaptiv ausgeglichen. Dies erfordert Vorhersagen der Tumorposition in die nahe Zukunft. Zahlreiche Pr{\"a}diktoren zur Atem- und Tumorpositionsvorhersage werden vorgeschlagen und anhand verschiedenster Metriken evaluiert. Erweiterungen der Pr{\"a}diktionsalgorithmen werden eingef{\"u}hrt, die sowohl Atem- als auch Tumorpositionsinformationen fusionieren, um Vorhersagen ohne explizites Korrelationsmodell zu erm{\"o}glichen. Die Vorhersagen bestimmen den zuk{\"u}nftigen Bewegungspfad des HexaPODs, um Tumorbewegungen zu kompensieren. Dazu werden verschiedene Regler entwickelt, die eine Trajektorienverfolgung mit dem HexaPOD erm{\"o}glichen. Auf der Basis von linearer und nicht-linearer dynamischer Modellierung des HexaPODs mit Methoden der Systemidentifikation, wird zun{\"a}chst ein modellpr{\"a}diktiver Regler entwickelt. Ein zweiter Regler wird auf Basis einer Annahme {\"u}ber das Arbeitsprinzip des internen Reglers im HexaPOD entworfen. Schließlich wird ein dritter Regler vorgeschlagen, der beide vorhergehenden Regler miteinander kombiniert. F{\"u}r jeden dieser Regler werden vergleichende Ergebnisse aus Experimenten mit realer Hardware und menschlichen Versuchspersonen pr{\"a}sentiert und diskutiert. Dar{\"u}ber hinaus wird die geeignete Wahl von freien Parametern in den Reglern vorgestellt. Neben einer pr{\"a}zisen Verfolgung der Referenztrajektorie spielt der Patientenkomfort eine entscheidende Rolle f{\"u}r die Akzeptanz des Systems. Es wird gezeigt, dass die Regler glatte Trajektorien realisieren k{\"o}nnen, um zu garantieren, dass sich Patienten wohl f{\"u}hlen w{\"a}hrend ihre Tumorbewegung mit Genauigkeiten im Submillimeterbereich ausgeglichen wird. Gesamtfehler werden im Kompensationssystem analysiert, in dem diese zu Trajektorienverfolgungsfehlern und Pr{\"a}diktionsfehlern in Beziehung gesetzt werden. Durch Ausnutzung von Eigenschaften verschiedener Pr{\"a}diktoren wird gezeigt, dass die Startzeit des Systems bis die Verfolgung der Referenztrajektorie erreicht ist, wenige Sekunden betr{\"a}gt. Dies gilt insbesondere f{\"u}r den Fall eines initial ruhenden HexaPODs und ohne Vorwissen {\"u}ber Tumorbewegungen. Dies zeigt die Eignung des Systems f{\"u}r die sehr kurz fraktionierten Behandlungen von Lungentumoren. Das Tumorkompensationssystem wurde ausschließlich auf Basis von klinischer Standard-Hardware entwickelt, die in vielen Behandlungsr{\"a}umen zu finden ist. Durch ein einfaches und flexibles Design k{\"o}nnen Behandlungsr{\"a}ume in kosteneffizienter Weise um M{\"o}glichkeiten der Bewegungskompensation erg{\"a}nzt werden. Dar{\"u}ber hinaus werden aktuelle Behandlungsmethoden wie intensit{\"a}tsmodulierte Strahlentherapie oder Volumetric Modulated Arc Therapy in keiner Weise eingeschr{\"a}nkt. Aufgrund der Unterst{\"u}tzung verschiedener Kompensationsmodi kann das System auf alle beweglichen Tumore angewendet werden, unabh{\"a}ngig davon ob die Bewegungen vorhersagbar (Lungentumore) oder nicht vorhersagbar (Prostatatumore) sind. Durch Integration von geeigneten Methoden zur Tumorpositionsbestimmung kann das System auf einfache Weise zur Kompensation von anderen Tumoren erweitert werden.}, subject = {Robotik}, language = {en} } @phdthesis{Reith2001, author = {Reith, Steffen}, title = {Generalized Satisfiability Problems}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-74}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2001}, abstract = {In the last 40 years, complexity theory has grown to a rich and powerful field in theoretical computer science. The main task of complexity theory is the classification of problems with respect to their consumption of resources (e.g., running time or required memory). To study the computational complexity (i.e., consumption of resources) of problems, similar problems are grouped into so called complexity classes. During the systematic study of numerous problems of practical relevance, no efficient algorithm for a great number of studied problems was found. Moreover, it was unclear whether such algorithms exist. A major breakthrough in this situation was the introduction of the complexity classes P and NP and the identification of hardest problems in NP. These hardest problems of NP are nowadays known as NP-complete problems. One prominent example of an NP-complete problem is the satisfiability problem of propositional formulas (SAT). Here we get a propositional formula as an input and it must be decided whether an assignment for the propositional variables exists, such that this assignment satisfies the given formula. The intensive study of NP led to numerous related classes, e.g., the classes of the polynomial-time hierarchy PH, P, \#P, PP, NL, L and \#L. During the study of these classes, problems related to propositional formulas were often identified to be complete problems for these classes. Hence some questions arise: Why is SAT so hard to solve? Are there modifications of SAT which are complete for other well-known complexity classes? In the context of these questions a result by E. Post is extremely useful. He identified and characterized all classes of Boolean functions being closed under superposition. It is possible to study problems which are connected to generalized propositional logic by using this result, which was done in this thesis. Hence, many different problems connected to propositional logic were studied and classified with respect to their computational complexity, clearing the borderline between easy and hard problems.}, subject = {Erf{\"u}llbarkeitsproblem}, language = {en} } @phdthesis{Kosub2001, author = {Kosub, Sven}, title = {Complexity and Partitions}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-2808}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2001}, abstract = {Computational complexity theory usually investigates the complexity of sets, i.e., the complexity of partitions into two parts. But often it is more appropriate to represent natural problems by partitions into more than two parts. A particularly interesting class of such problems consists of classification problems for relations. For instance, a binary relation R typically defines a partitioning of the set of all pairs (x,y) into four parts, classifiable according to the cases where R(x,y) and R(y,x) hold, only R(x,y) or only R(y,x) holds or even neither R(x,y) nor R(y,x) is true. By means of concrete classification problems such as Graph Embedding or Entailment (for propositional logic), this thesis systematically develops tools, in shape of the boolean hierarchy of NP-partitions and its refinements, for the qualitative analysis of the complexity of partitions generated by NP-relations. The Boolean hierarchy of NP-partitions is introduced as a generalization of the well-known and well-studied Boolean hierarchy (of sets) over NP. Whereas the latter hierarchy has a very simple structure, the situation is much more complicated for the case of partitions into at least three parts. To get an idea of this hierarchy, alternative descriptions of the partition classes are given in terms of finite, labeled lattices. Based on these characterizations the Embedding Conjecture is established providing the complete information on the structure of the hierarchy. This conjecture is supported by several results. A natural extension of the Boolean hierarchy of NP-partitions emerges from the lattice-characterization of its classes by considering partition classes generated by finite, labeled posets. It turns out that all significant ideas translate from the case of lattices. The induced refined Boolean hierarchy of NP-partitions enables us more accuratly capturing the complexity of certain relations (such as Graph Embedding) and a description of projectively closed partition classes.}, subject = {Partition }, language = {en} } @phdthesis{Schmitz2000, author = {Schmitz, Heinz}, title = {The Forbidden Pattern Approach to Concatenation Hierarchies}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-2832}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2000}, abstract = {The thesis looks at the question asking for the computability of the dot-depth of star-free regular languages. Here one has to determine for a given star-free regular language the minimal number of alternations between concatenation on one hand, and intersection, union, complement on the other hand. This question was first raised in 1971 (Brzozowski/Cohen) and besides the extended star-heights problem usually refered to as one of the most difficult open questions on regular languages. The dot-depth problem can be captured formally by hierarchies of classes of star-free regular languages B(0), B(1/2), B(1), B(3/2),... and L(0), L(1/2), L(1), L(3/2),.... which are defined via alternating the closure under concatenation and Boolean operations, beginning with single alphabet letters. Now the question of dot-depth is the question whether these hierarchy classes have decidable membership problems. The thesis makes progress on this question using the so-called forbidden pattern approach: Classes of regular languages are characterized in terms of patterns in finite automata (subgraphs in the transition graph) that are not allowed. Such a characterization immediately implies the decidability of the respective class, since the absence of a certain pattern in a given automaton can be effectively verified. Before this work, the decidability of B(0), B(1/2), B(1) and L(0), L(1/2), L(1), L(3/2) were known. Here a detailed study of these classes with help of forbidden patterns is given which leads to new insights into their inner structure. Furthermore, the decidability of B(3/2) is proven. Based on these results a theory of pattern iteration is developed which leads to the introduction of two new hierarchies of star-free regular languages. These hierarchies are decidable on one hand, on the other hand they are in close connection to the classes B(n) and L(n). It remains an open question here whether they may in fact coincide. Some evidence is given in favour of this conjecture which opens a new way to attack the dot-depth problem. Moreover, it is shown that the class L(5/2) is decidable in the restricted case of a two-letter alphabet.}, subject = {Sternfreie Sprache}, language = {en} } @phdthesis{Wirth2001, author = {Wirth, Hans-Christoph}, title = {Multicriteria Approximation of Network Design and Network Upgrade Problems}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-2845}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2001}, abstract = {Network planning has come to great importance during the past decades. Today's telecommunication, traffic systems, and logistics would not have been evolved to the current state without careful analysis of the underlying network problems and precise implementation of the results obtained from those examinations. Graphs with node and arc attributes are a very useful tool to model realistic applications, while on the other hand they are well understood in theory. We investigate network design problems which are motivated particularly from applications in communication networks and logistics. Those problems include the search for homogeneous subgraphs in edge labeled graphs where either the total number of labels or the reload cost are subject to optimize. Further, we investigate some variants of the dial a ride problem. On the other hand, we use node and edge upgrade models to deal with the fact that in many cases one prefers to change existing networks rather than implementing a newly computed solution from scratch. We investigate the construction of bottleneck constrained forests under a node upgrade model, as well as several flow cost problems under a edge based upgrade model. All problems are examined within a framework of multi-criteria optimization. Many of the problems can be shown to be NP-hard, with the consequence that, under the widely accepted assumption that P is not equal to NP, there cannot exist efficient algorithms for solving the problems. This motivates the development of approximation algorithms which compute near-optimal solutions with provable performance guarantee in polynomial time.}, subject = {Netzplantechnik}, language = {en} } @phdthesis{Glasser2001, author = {Glaßer, Christian}, title = {Forbidden-Patterns and Word Extensions for Concatenation Hierarchies}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-1179153}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2001}, abstract = {Starfree regular languages can be build up from alphabet letters by using only Boolean operations and concatenation. The complexity of these languages can be measured with the so-called dot-depth. This measure leads to concatenation hierarchies like the dot-depth hierarchy (DDH) and the closely related Straubing-Th{\´e}rien hierarchy (STH). The question whether the single levels of these hierarchies are decidable is still open and is known as the dot-depth problem. In this thesis we prove/reprove the decidability of some lower levels of both hierarchies. More precisely, we characterize these levels in terms of patterns in finite automata (subgraphs in the transition graph) that are not allowed. Therefore, such characterizations are called forbidden-pattern characterizations. The main results of the thesis are as follows: forbidden-pattern characterization for level 3/2 of the DDH (this implies the decidability of this level) decidability of the Boolean hierarchy over level 1/2 of the DDH definition of decidable hierarchies having close relations to the DDH and STH Moreover, we prove/reprove the decidability of the levels 1/2 and 3/2 of both hierarchies in terms of forbidden-pattern characterizations. We show the decidability of the Boolean hierarchies over level 1/2 of the DDH and over level 1/2 of the STH. A technique which uses word extensions plays the central role in the proofs of these results. With this technique it is possible to treat the levels 1/2 and 3/2 of both hierarchies in a uniform way. Furthermore, it can be used to prove the decidability of the mentioned Boolean hierarchies. Among other things we provide a combinatorial tool that allows to partition words of arbitrary length into factors of bounded length such that every second factor u leads to a loop with label u in a given finite automaton.}, subject = {Automatentheorie}, language = {en} } @phdthesis{Kluegl2000, author = {Kl{\"u}gl, Franziska}, title = {Aktivit{\"a}tsbasierte Verhaltensmodellierung und ihre Unterst{\"u}tzung bei Multiagentensimulationen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-2874}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2000}, abstract = {Durch Zusammenf{\"u}hrung traditioneller Methoden zur individuenbasierten Simulation und dem Konzept der Multiagentensysteme steht mit der Multiagentensimulation eine Methodik zur Verf{\"u}gung, die es erm{\"o}glicht, sowohl technisch als auch konzeptionell eine neue Ebene an Detaillierung bei Modellbildung und Simulation zu erreichen. Ein Modell beruht dabei auf dem Konzept einer Gesellschaft: Es besteht aus einer Menge interagierender, aber in ihren Entscheidungen autonomen Einheiten, den Agenten. Diese {\"a}ndern durch ihre Aktionen ihre Umwelt und reagieren ebenso auf die f{\"u}r sie wahrnehmbaren {\"A}nderungen in der Umwelt. Durch die Simulation jedes Agenten zusammen mit der Umwelt, in der er "lebt", wird die Dynamik im Gesamtsystem beobachtbar. In der vorliegenden Dissertation wurde ein Repr{\"a}sentationsschema f{\"u}r Multiagentensimulationen entwickelt werden, das es Fachexperten, wie zum Beispiel Biologen, erm{\"o}glicht, selbst{\"a}ndig ohne traditionelles Programmieren Multiagentenmodelle zu implementieren und mit diesen Experimente durchzuf{\"u}hren. Dieses deklarative Schema beruht auf zwei Basiskonzepten: Der K{\"o}rper eines Agenten besteht aus Zustandsvariablen. Das Verhalten des Agenten kann mit Regeln beschrieben werden. Ausgehend davon werden verschiedene Strukturierungsans{\"a}tze behandelt. Das wichtigste Konzept ist das der "Aktivit{\"a}t", einer Art "Verhaltenszustand": W{\"a}hrend der Agent in einer Aktivit{\"a}t A verweilt, f{\"u}hrt er die zugeh{\"o}rigen Aktionen aus und dies solange, bis eine Regel feuert, die diese Aktivit{\"a}t beendet und eine neue Aktivit{\"a}t ausw{\"a}hlt. Durch Indizierung dieser Regeln bei den zugeh{\"o}rigen Aktivit{\"a}ten und Einf{\"u}hrung von abstrakten Aktivit{\"a}ten entsteht ein Schema f{\"u}r eine vielf{\"a}ltig strukturierbare Verhaltensbeschreibung. Zu diesem Schema wurde ein Interpreter entwickelt, der ein derartig repr{\"a}sentiertes Modell ausf{\"u}hrt und so Simulationsexperimente mit dem Multiagentenmodell erlaubt. Auf dieser Basis wurde die Modellierungs- und Experimentierumgebung SeSAm ("Shell f{\"u}r Simulierte Agentensysteme") entwickelt. Sie verwendet vorhandene Konzepte aus dem visuellen Programmieren. Mit dieser Umgebung wurden Anwendungsmodelle aus verschiedenen Dom{\"a}nen realisiert: Neben abstrakten Spielbeispielen waren dies vor allem Fragestellungen zu sozialen Insekten, z.B. zum Verhalten von Ameisen, Bienen oder der Interaktion zwischen Bienenv{\"o}lkern und Milbenpopulationen.}, subject = {Agent }, language = {de} } @phdthesis{Schaefer2003, author = {Sch{\"a}fer, Dirk}, title = {Globale Selbstlokalisation autonomer mobiler Roboter - Ein Schl{\"u}sselproblem der Service-Robotik}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-7601}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2003}, abstract = {Die Dissertation behandelt die Problemstellung der globalen Selbstlokalisation autonomer mobiler Roboter, welche folgendermaßen beschrieben werden kann: Ein mobiler Roboter, eingesetzt in einem Geb{\"a}ude, kann unter Umst{\"a}nden das Wissen {\"u}ber seinen Standort verlieren. Man geht nun davon aus, dass dem Roboter eine Geb{\"a}udekarte als Modell zur Verf{\"u}gung steht. Mit Hilfe eines Laser-Entfernungsmessers kann das mobile Ger{\"a}t neue Informationen aufnehmen und damit bei korrekter Zuordnung zur Modellkarte geeignete hypothetische Standorte ermitteln. In der Regel werden diese Positionen aber mehrdeutig sein. Indem sich der Roboter intelligent in seiner Einsatzumgebung bewegt, kann er die urspr{\"u}nglichen Sensordaten verifizieren und ermittelt im besten Fall seine tats{\"a}chliche Position.F{\"u}r diese Problemstellung wird ein neuer L{\"o}sungsansatz in Theorie und Praxis pr{\"a}sentiert, welcher die jeweils aktuelle lokale Karte und damit alle Sensordaten mittels feature-basierter Matchingverfahren auf das Modell der Umgebung abbildet. Ein Explorationsalgorithmus bewegt den Roboter w{\"a}hrend der Bewegungsphase autonom zu Sensorpunkten, welche neue Informationen bereitstellen. W{\"a}hrend der Bewegungsphase werden dabei die bisherigen hypothetischen Positionen best{\"a}rkt oder geschw{\"a}cht, sodaß nach kurzer Zeit eine dominante Position, die tats{\"a}chliche Roboterposition,{\"u}brigbleibt.}, subject = {Mobiler Roboter}, language = {de} } @phdthesis{Heck2005, author = {Heck, Klaus}, title = {Wireless LAN performance studies in the context of 4G networks}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-14896}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2005}, abstract = {Wireless communication is nothing new. The first data transmissions based on electromagnetic waves have been successfully performed at the end of the 19th century. However, it took almost another century until the technology was ripe for mass market. The first mobile communication systems based on the transmission of digital data were introduced in the late 1980s. Within just a couple of years they have caused a revolution in the way people communicate. The number of cellular phones started to outnumber the fixed telephone lines in many countries and is still rising. New technologies in 3G systems, such as UMTS, allow higher data rates and support various kinds of multimedia services. Nevertheless, the end of the road in wireless communication is far from being reached. In the near future, the Internet and cellular phone systems are expected to be integrated to a new form of wireless system. Bandwidth requirements for a rich set of wireless services, e.g.\ video telephony, video streaming, online gaming, will be easily met. The transmission of voice data will just be another IP based service. On the other hand, building such a system is by far not an easy task. The problems in the development of the UMTS system showed the high complexity of wireless systems with support for bandwidth-hungry, IP-based services. But the technological challenges are just one difficulty. Telecommunication systems are planned on a world-wide basis, such that standard bodies, governments, institutions, hardware vendors, and service providers have to find agreements and compromises on a number of different topics. In this work, we provide the reader with a discussion of many of the topics involved in the planning of a Wireless LAN system that is capable of being integrated into the 4th generation mobile networks (4G) that is being discussed nowadays. Therefore, it has to be able to cope with interactive voice and video traffic while still offering high data rates for best effort traffic. Let us assume a scenario where a huge office complex is completely covered with Wireless LAN access points. Different antenna systems are applied in order to reduce the number of access points that are needed on the one hand, while optimizing the coverage on the other. No additional infrastructure is implemented. Our goal is to evaluate whether the Wireless LAN technology is capable of dealing with the various demands of such a scenario. First, each single access point has to be capable of supporting best-effort and Quality of Service (QoS) demanding applications simultaneously. The IT infrastructure in our scenario consists solely of Wireless LAN, such that it has to allow users surfing the Web, while others are involved in voice calls or video conferences. Then, there is the problem of overlapping cells. Users attached to one access point produce interference for others. However, the QoS support has to be maintained, which is not an easy task. Finally, there are nomadic users, which roam from one Wireless LAN cell to another even during a voice call. There are mechanisms in the standard that allow for mobility, but their capabilities for QoS support are yet to be studied. This shows the large number of unresolved issues when it comes to Wireless LAN in the context of 4G networks. In this work we want to tackle some of the problems.}, subject = {Drahtloses lokales Netz}, language = {en} } @phdthesis{Kluge2004, author = {Kluge, Boris}, title = {Motion coordination for a mobile robot in dynamic environments}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-15508}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2004}, abstract = {Generating coordinated motion for a mobile robot operating in natural, continuously changing environments among moving obstacles such as humans is a complex task which requires the solution of various sub problems. In this thesis, we will cover the topics of perception and navigation in dynamic environments, as well as reasoning about the motion of the obstacles and of the robot itself. Perception is mainly considered for a laser range finder, and an according method for obstacle detection and tracking is proposed. Network optimization algorithms are used for data association in the tracking step, resulting in considerable robustness with respect to clutter by small objects. Navigation in general is accomplished using an adaptation of the velocity obstacle approach to the given vehicle kinematics, and cooperative motion coordination between the robot and a human guide is achieved using an appropriate selection rule for collision-free velocities. Next, the robot is enabled to compare its path to the path of a human guide using one of a collection of presented distance measures, which permits the detection of exceptional conditions. Furthermore, a taxonomy for the assessment of situations concerning the robot is presented, and following a summary of existing approaches to more intelligent and comprehensive perception, we propose a method for obstruction detection. Finally, a new approach to reflective navigation behaviors is described where the robot reasons about intelligent moving obstacles in its environment, which allows to adjust the character of the robot motion from regardful and defensive to more self-confident and aggressive behaviors.}, subject = {Bewegungsablauf}, language = {de} } @phdthesis{Eichelberger2005, author = {Eichelberger, Holger}, title = {Aesthetics and automatic layout of UML class diagrams}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-14831}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2005}, abstract = {In the last years, visual methods have been introduced in industrial software production and teaching of software engineering. In particular, the international standardization of a graphical software engineering language, the Unified Modeling Language (UML) was a reason for this tendency. Unfortunately, various problems exist in concrete realizations of tools, e.g. due to a missing compliance to the standard. One problem is the automatic layout, which is required for a consistent automatic software design. The thesis derives reasons and criteria for an automatic layout method, which produces drawings of UML class diagrams according to the UML specification and issues of human computer interaction, e.g. readability. A unique set of aesthetic criteria is combined from four different disciplines involved in this topic. Based on these aethetic rules, a hierarchical layout algorithm is developed, analyzed, measured by specialized measuring techniques and compared to related work. Then, the realization of the algorithm as a Java framework is given as an architectural description. Finally, adaptions to anticipated future changes of the UML, improvements of the framework and example drawings of the implementation are given.}, subject = {URL}, language = {en} } @phdthesis{Menth2004, author = {Menth, Michael}, title = {Efficient admission control and routing for resilient communication networks}, doi = {10.25972/OPUS-846}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-9949}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2004}, abstract = {This work is subdivided into two main areas: resilient admission control and resilient routing. The work gives an overview of the state of the art of quality of service mechanisms in communication networks and proposes a categorization of admission control (AC) methods. These approaches are investigated regarding performance, more precisely, regarding the potential resource utilization by dimensioning the capacity for a network with a given topology, traffic matrix, and a required flow blocking probability. In case of a failure, the affected traffic is rerouted over backup paths which increases the traffic rate on the respective links. To guarantee the effectiveness of admission control also in failure scenarios, the increased traffic rate must be taken into account for capacity dimensioning and leads to resilient AC. Capacity dimensioning is not feasible for existing networks with already given link capacities. For the application of resilient NAC in this case, the size of distributed AC budgets must be adapted according to the traffic matrix in such a way that the maximum blocking probability for all flows is minimized and that the capacity of all links is not exceeded by the admissible traffic rate in any failure scenario. Several algorithms for the solution of that problem are presented and compared regarding their efficiency and fairness. A prototype for resilient AC was implemented in the laboratories of Siemens AG in Munich within the scope of the project KING. Resilience requires additional capacity on the backup paths for failure scenarios. The amount of this backup capacity depends on the routing and can be minimized by routing optimization. New protection switching mechanisms are presented that deviate the traffic quickly around outage locations. They are simple and can be implemented, e.g, by MPLS technology. The Self-Protecting Multi-Path (SPM) is a multi-path consisting of disjoint partial paths. The traffic is distributed over all faultless partial paths according to an optimized load balancing function both in the working case and in failure scenarios. Performance studies show that the network topology and the traffic matrix also influence the amount of required backup capacity significantly. The example of the COST-239 network illustrates that conventional shortest path routing may need 50\% more capacity than the optimized SPM if all single link and node failures are protected.}, subject = {Kommunikation}, language = {en} } @phdthesis{Boehler2005, author = {B{\"o}hler, Elmar}, title = {Algebraic closures in complexity theory}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-16106}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2005}, abstract = {We use algebraic closures and structures which are derived from these in complexity theory. We classify problems with Boolean circuits and Boolean constraints according to their complexity. We transfer algebraic structures to structural complexity. We use the generation problem to classify important complexity classes.}, subject = {Komplexit{\"a}tstheorie}, language = {en} } @phdthesis{Betz2005, author = {Betz, Christian}, title = {Scalable authoring of diagnostic case based training systems}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-17885}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2005}, abstract = {Diagnostic Case Based Training Systems (D-CBT) provide learners with a means to learn and exercise knowledge in a realistic context. In medical education, D-CBT Systems present virtual patients to the learners who are asked to examine, diagnose and state therapies for these patients. Due a number of conflicting and changing requirements, e.g. time for learning, authoring effort, several systems were developed so far. These systems range from simple, easy-to-use presentation systems to highly complex knowledge based systems supporting explorative learning. This thesis presents an approach and tools to create D-CBT systems from existing sources (documents, e.g. dismissal records) using existing tools (word processors): Authors annotate and extend the documents to model the knowledge. A scalable knowledge representation is able to capture the content on multiple levels, from simple to highly structured knowledge. Thus, authoring of D-CBT systems requires less prerequisites and pre-knowledge and is faster than approaches using specialized authoring environments. Also, authors can iteratively add and structure more knowledge to adapt training cases to their learners needs. The theses also discusses the application of the same approach to other domains, especially to knowledge acquisition for the Semantic Web.}, subject = {Computerunterst{\"u}tztes Lernen}, language = {en} } @phdthesis{Milbrandt2007, author = {Milbrandt, Jens}, title = {Performance Evaluation of Efficient Resource Management Concepts for Next Generation IP Networks}, doi = {10.25972/OPUS-1991}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-23332}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2007}, abstract = {Next generation networks (NGNs) must integrate the services of current circuit-switched telephone networks and packet-switched data networks. This convergence towards a unified communication infrastructure necessitates from the high capital expenditures (CAPEX) and operational expenditures (OPEX) due to the coexistence of separate networks for voice and data. In the end, NGNs must offer the same services as these legacy networks and, therefore, they must provide a low-cost packet-switched solution with real-time transport capabilities for telephony and multimedia applications. In addition, NGNs must be fault-tolerant to guarantee user satisfaction and to support business-critical processes also in case of network failures. A key technology for the operation of NGNs is the Internet Protocol (IP) which evolved to a common and well accepted standard for networking in the Internet during the last 25 years. There are two basically different approaches to achieve QoS in IP networks. With capacity overprovisioning (CO), an IP network is equipped with sufficient bandwidth such that network congestion becomes very unlikely and QoS is maintained most of the time. The second option to achieve QoS in IP networks is admission control (AC). AC represents a network-inherent intelligence that admits real-time traffic flows to a single link or an entire network only if enough resources are available such that the requirements on packet loss and delay can be met. Otherwise, the request of a new flow is blocked. This work focuses on resource management and control mechanisms for NGNs, in particular on AC and associated bandwidth allocation methods. The first contribution consists of a new link-oriented AC method called experience-based admission control (EBAC) which is a hybrid approach dealing with the problems inherent to conventional AC mechanisms like parameter-based or measurement-based AC (PBAC/MBAC). PBAC provides good QoS but suffers from poor resource utilization and, vice versa, MBAC uses resources efficiently but is susceptible to QoS violations. Hence, EBAC aims at increasing the resource efficiency while maintaining the QoS which increases the revenues of ISPs and postpones their CAPEX for infrastructure upgrades. To show the advantages of EBAC, we first review today's AC approaches and then develop the concept of EBAC. EBAC is a simple mechanism that safely overbooks the capacity of a single link to increase its resource utilization. We evaluate the performance of EBAC by its simulation under various traffic conditions. The second contribution concerns dynamic resource allocation in transport networks which implement a specific network admission control (NAC) architecture. In general, the performance of different NAC systems may be evaluated by conventional methods such as call blocking analysis which has often been applied in the context of multi-service asynchronous transfer mode (ATM) networks. However, to yield more practical results than abstract blocking probabilities, we propose a new method to compare different AC approaches by their respective bandwidth requirements. To present our new method for comparing different AC systems, we first give an overview of network resource management (NRM) in general. Then we present the concept of adaptive bandwidth allocation (ABA) in capacity tunnels and illustrate the analytical performance evaluation framework to compare different AC systems by their capacity requirements. Different network characteristics influence the performance of ABA. Therefore, the impact of various traffic demand models and tunnel implementations, and the influence of resilience requirements is investigated. In conclusion, the resources in NGNs must be exclusively dedicated to admitted traffic to guarantee QoS. For that purpose, robust and efficient concepts for NRM are required to control the requested bandwidth with regard to the available transmission capacity. Sophisticated AC will be a key function for NRM in NGNs and, therefore, efficient resource management concepts like experience-based admission control and adaptive bandwidth allocation for admission-controlled capacity tunnels, as presented in this work are appealing for NGN solutions.}, subject = {Ressourcenmanagement}, language = {en} } @phdthesis{Atzmueller2006, author = {Atzm{\"u}ller, Martin}, title = {Knowledge-Intensive Subgroup Mining - Techniques for Automatic and Interactive Discovery}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-21004}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2006}, abstract = {Data mining has proved its significance in various domains and applications. As an important subfield of the general data mining task, subgroup mining can be used, e.g., for marketing purposes in business domains, or for quality profiling and analysis in medical domains. The goal is to efficiently discover novel, potentially useful and ultimately interesting knowledge. However, in real-world situations these requirements often cannot be fulfilled, e.g., if the applied methods do not scale for large data sets, if too many results are presented to the user, or if many of the discovered patterns are already known to the user. This thesis proposes a combination of several techniques in order to cope with the sketched problems: We discuss automatic methods, including heuristic and exhaustive approaches, and especially present the novel SD-Map algorithm for exhaustive subgroup discovery that is fast and effective. For an interactive approach we describe techniques for subgroup introspection and analysis, and we present advanced visualization methods, e.g., the zoomtable that directly shows the most important parameters of a subgroup and that can be used for optimization and exploration. We also describe various visualizations for subgroup comparison and evaluation in order to support the user during these essential steps. Furthermore, we propose to include possibly available background knowledge that is easy to formalize into the mining process. We can utilize the knowledge in many ways: To focus the search process, to restrict the search space, and ultimately to increase the efficiency of the discovery method. We especially present background knowledge to be applied for filtering the elements of the problem domain, for constructing abstractions, for aggregating values of attributes, and for the post-processing of the discovered set of patterns. Finally, the techniques are combined into a knowledge-intensive process supporting both automatic and interactive methods for subgroup mining. The practical significance of the proposed approach strongly depends on the available tools. We introduce the VIKAMINE system as a highly-integrated environment for knowledge-intensive active subgroup mining. Also, we present an evaluation consisting of two parts: With respect to objective evaluation criteria, i.e., comparing the efficiency and the effectiveness of the subgroup discovery methods, we provide an experimental evaluation using generated data. For that task we present a novel data generator that allows a simple and intuitive specification of the data characteristics. The results of the experimental evaluation indicate that the novel SD-Map method outperforms the other described algorithms using data sets similar to the intended application concerning the efficiency, and also with respect to precision and recall for the heuristic methods. Subjective evaluation criteria include the user acceptance, the benefit of the approach, and the interestingness of the results. We present five case studies utilizing the presented techniques: The approach has been successfully implemented in medical and technical applications using real-world data sets. The method was very well accepted by the users that were able to discover novel, useful, and interesting knowledge.}, subject = {Data Mining}, language = {en} } @phdthesis{Travers2007, author = {Travers, Stephen}, title = {Structural Properties of NP-Hard Sets and Uniform Characterisations of Complexity Classes}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-27124}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2007}, abstract = {This thesis is devoted to the study of computational complexity theory, a branch of theoretical computer science. Computational complexity theory investigates the inherent difficulty in designing efficient algorithms for computational problems. By doing so, it analyses the scalability of computational problems and algorithms and places practical limits on what computers can actually accomplish. Computational problems are categorised into complexity classes. Among the most important complexity classes are the class NP and the subclass of NP-complete problems, which comprises many important optimisation problems in the field of operations research. Moreover, with the P-NP-problem, the class NP represents the most important unsolved question in computer science. The first part of this thesis is devoted to the study of NP-complete-, and more generally, NP-hard problems. It aims at improving our understanding of this important complexity class by systematically studying how altering NP-hard sets affects their NP-hardness. This research is related to longstanding open questions concerning the complexity of unions of disjoint NP-complete sets, and the existence of sparse NP-hard sets. The second part of the thesis is also dedicated to complexity classes but takes a different perspective: In a sense, after investigating the interior of complexity classes in the first part, the focus shifts to the description of complexity classes and thereby to the exterior in the second part. It deals with the description of complexity classes through leaf languages, a uniform framework which allows us to characterise a great variety of important complexity classes. The known concepts are complemented by a new leaf-language model. To a certain extent, this new approach combines the advantages of the known models. The presented results give evidence that the connection between the theory of formal languages and computational complexity theory might be closer than formerly known.}, subject = {Berechnungskomplexit{\"a}t}, language = {en} } @misc{Feineis2008, type = {Master Thesis}, author = {Feineis, Markus}, title = {Wortgenaue Annotation digitalisierter mittelalterlicher Handschriften}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-30448}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2008}, abstract = {No abstract available}, subject = {Annotation}, language = {de} } @phdthesis{Maeder2008, author = {M{\"a}der, Andreas}, title = {Performance Models for UMTS 3.5G Mobile Wireless Systems}, doi = {10.25972/OPUS-2766}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-32525}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2008}, abstract = {Mobile telecommunication systems of the 3.5th generation (3.5G) constitute a first step towards the requirements of an all-IP world. As the denotation suggests, 3.5G systems are not completely new designed from scratch. Instead, they are evolved from existing 3G systems like UMTS or cdma2000. 3.5G systems are primarily designed and optimized for packet-switched best-effort traffic, but they are also intended to increase system capacity by exploiting available radio resources more efficiently. Systems based on cdma2000 are enhanced with 1xEV-DO (EV-DO: evolution, data-optimized). In the UMTS domain, the 3G partnership project (3GPP) specified the High Speed Packet Access (HSPA) family, consisting of High Speed Downlink Packet Access (HSDPA) and its counterpart High Speed Uplink Packet Access (HSUPA) or Enhanced Uplink. The focus of this monograph is on HSPA systems, although the operation principles of other 3.5G systems are similar. One of the main contributions of our work are performance models which allow a holistic view on the system. The models consider user traffic on flow-level, such that only on significant changes of the system state a recalculation of parameters like bandwidth is necessary. The impact of lower layers is captured by stochastic models. This approach combines accurate modeling and the ability to cope with computational complexity. Adopting this approach to HSDPA, we develop a new physical layer abstraction model that takes radio resources, scheduling discipline, radio propagation and mobile device capabilities into account. Together with models for the calculation of network-wide interference and transmit powers, a discrete-event simulation and an analytical model based on a queuing-theoretical approach are proposed. For the Enhanced Uplink, we develop analytical models considering independent and correlated other-cell interference.}, subject = {Mobilfunk}, language = {en} } @phdthesis{Tischler2008, author = {Tischler, German}, title = {Theory and Applications of Parametric Weighted Finite Automata}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-28145}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2008}, abstract = {Parametric weighted finite automata (PWFA) are a multi-dimensional generalization of weighted finite automata. The expressiveness of PWFA contains the expressiveness of weighted finite automata as well as the expressiveness of affine iterated function system. The thesis discusses theory and applications of PWFA. The properties of PWFA definable sets are studied and it is shown that some fractal generator systems can be simulated using PWFA and that various real and complex functions can be represented by PWFA. Furthermore, the decoding of PWFA and the interpretation of PWFA definable sets is discussed.}, subject = {Automat }, language = {en} }