@phdthesis{Schmitz2016,
  author    = {Schmitz, Tobias},
  title     = {Functional coatings by physical vapor deposition (PVD) for biomedical applications},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-144825},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2016},
  abstract  = {Metals are the most used materials for implant devices, especially in orthopedics, but despite their long history of application issues such as material failure through wear and corrosion remain unsolved leading to a certain number of revision surgeries. Apart from the problems associated with insufficient material properties, another serious issue is an implant associated infection due to the formation of a biofilm on the surface of the material after implantation. Thus, improvements in implant technology are demanded, especially since there is a projected rise of implants needed in the future. Surface modification methods such as physical vapour deposition (PVD), oxygen diffusion hardening and electrochemical anodization have shown to be efficient methods to improve the surfaces of metallic bulk materials regarding biomedical issues. This thesis was focused on the development of functional PVD coatings that are suitable for further treatment with surface modification techniques originally developed for bulk metals. The aim was to precisely adjust the surface properties of the implant according to the targeted application to prevent possible failure mechanisms such as coating delamination, wear or the occurrence of post-operative infections. Initially,  tantalum layers with approx 5 µm thickness were deposited at elevated substrate temperatures on cp Ti by RF magnetron sputtering. Due to the high affinity of tantalum to oxygen, these coatings are known to provide a self healing capacity since the rapid oxide formation is known to close surface cracks. Here, the work aimed to reduce the abrupt change of mechanical properties between the hard and brittle coating and the ductile substrate by creating an oxygen diffusion zone. It was found that the hardness and adhesion could be significantly increased when the coatings were treated afterwards by oxygen diffusion hardening in a two step process. Firstly, the surface was oxidized at a pressure of 6.7•10-3 mbar at 350 450 °C, followed by 1-2 h annealing in oxygen-free atmosphere at the same temperature leading to a diffusion of oxygen atoms into deeper parts of the substrate as proved by X-ray diffraction (XRD) analysis. The hereby caused mechanical stress in the crystal lattice led to an increase in Vickers hardness of the Ta layers from 570 HV to over 900 HV. Investigations into the adhesion of oxygen diffusion treated samples by Rockwell measurements demonstrated an increase of critical force for coating delamination from 12 N for untreated samples up to 25 N for diffusion treated samples. In a second approach, the development of modular targets aimed to produce functional coatings by metallic doping of titanium with biologically active agents. This was demonstrated by the fabrication of antimicrobial Ti(Ag) coatings using a single magnetron sputtering source equipped with a titanium target containing implemented silver modules under variation of bias voltage and substrate temperature. The deposition of both Ti and Ag was confirmed by X-ray diffraction and a clear correlation between the applied sputtering parameters and the silver content of the coatings was demonstrated by ICP-MS and EDX. Surface-sensitive XPS measurements revealed that higher substrate temperatures led to an accumulation of Ag in the near-surface region, while the application of a bias voltage had the opposite effect. SEM and AFM microscopy revealed that substrate heating during film deposition supported the formation of even and dense surface layers with small roughness values, which could even be enforced by applying a substrate bias voltage. Additional elution measurements using ICP-MS showed that the release kinetics depended on the amount of silver located at the film surface and hence could be tailored by variation of the sputter parameters. In a final step, the applied Ti and Ti(Ag) coatings deposited on cp Ti, stainless steel (316L) and glass substrates were subsequently nanostructured using a self-ordering process induced by electrochemical anodization in aqueous fluoride containing electrolytes. SEM analysis showed that nanotube arrays could be grown from the Ti and Ti(Ag) coatings deposited at elevated temperatures on any substrate, whereby no influence of the substrate on nanotube morphology could be observed. EDX measurements indicated that the anodization process led to the selective etching of Ti from Ti(Ag) coating. Further experiments on coatings deposited on glass surfaces revealed that moderate substrate temperatures during deposition resulting in smooth Ti layers as determined by AFM measurements, are favorable for the generation of highly ordered nanotube arrays. Such arrays exhibited superhydrophilic behavior as proved by contact angle measurements. XRD analysis revealed that the nanostructured coatings were amorphous after anodization but could be crystallized to anatase structure by thermal treatment at temperatures of 450°C.},
  subject      = {PVD-Verfahren},
  language  = {en}
}
@phdthesis{Stuckensen2016,
  author    = {Stuckensen, Kai},
  title     = {Fabrication of hierarchical cell carrier matrices for tissue regeneration by directional solidification},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-145510},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2016},
  abstract  = {The key hypothesis of this work represented the question, if mimicking the zonal composition and structural porosity of musculoskeletal tissues influences invading cells positively and leads to advantageous results for tissue engineering. Conventional approaches in tissue engineering are limited in producing monolithic "scaffolds" that provide locally variating biological key signals and pore architectures, imitating the alignment of collagenous fibres in bone and cartilage tissues, respectively. In order to fill this gap in available tissue engineering strategies, a new fabrication technique was evolved for the production of scaffolds to validate the hypothesis. Therefore, a new solidification based platform procedure was developed. This process comprises the directional solidification of multiple flowable precursors that are "cryostructured" to prepare a controlled anisotropic pore structure. Porous scaffolds are attained through ice crystal removal by lyophilisation. Optionally, electrostatic spinning of polymers may be applied to provide an external mesh on top or around the scaffolds. A consolidation step generates monolithic matrices from multi zonal structures. To serve as matrix for tissue engineering approaches or direct implantation as medical device, the scaffold is sterilized. An Adjustable Cryostructuring Device (ACD) was successively developed; individual parts were conceptualized by computer aided design (CAD) and assembled. During optimisation, a significant performance improvement of the ACDs accessible external temperature gradient was achieved, from (1.3 ± 0.1) K/mm to (9.0 ± 0.1) K/mm. Additionally, four different configurations of the device were made available that enabled the directional solidification of collagenous precursors in a highly controlled manner with various sample sizes and shapes. By using alginate as a model substance the process was systematically evaluated. Cryostructuring diagraphs were analysed yielding solidification parameters, which were associated to pore sizes and alignments that were determined by image processing. Thereby, a precise control over pore size and alignment through electrical regulation of the ACD could be demonstrated. To obtain tissue mimetic scaffolds for the musculoskeletal system, collagens and calcium phosphates had to be prepared to serve as raw materials. Extraction and purification protocols were established to generate collagen I and collagen II, while the calcium phosphates brushite and hydroxyapatite were produced by precipitation reactions. Besides the successive augmentation of the ACD also an optimization of the processing steps was crucial. Firstly, the concentrations and the individual behaviour of respective precursor components had to be screened. Together with the insights gained by videographic examination of solidifying collagen solutions, essential knowledge was gained that facilitated the production of more complex scaffolds. Phenomena of ice crystal growth during cryostructuring were discussed. By evolutionary steps, a cryostructuring of multi-layered precursors with consecutive anisotropic pores could be achieved and successfully transferred from alginate to collagenous precursors. Finally, very smooth interfaces that were hardly detectable by scanning electron microscopy (SEM) could be attained. For the used collagenous systems, a dependency relation between adjustable processing parameters and different resulting solidification morphologies was created. Dehydrothermal-, diisocyanate-, and carbodiimide- based cross linking methods were evaluated, whereby the "zero length" cross linking by carbodiimide was found to be most suitable. Afterwards, a formulation for the cross linking solution was elaborated, which generated favourable outcomes by application inside a reduced pressure apparatus. As a consequence, a pore collapse during wet chemical cross linking could be avoided. Complex monolithic scaffolds featuring continuous pores were fabricated that mimicked structure and respective composition of different areas of native tissues by the presence of biochemical key stimulants. At first, three types of bone scaffolds were produced from collagen I and hydroxyapatite with appropriate sizes to fit critical sized defects in rat femurs. They either featured an isotropic or anisotropic porosity and partly also contained glycosaminoglycans (GAGs). Furthermore, meniscus scaffolds were prepared by processing two precursors with biomimetic contents of collagen I, collagen II and GAGs. Here, the pore structures were created under boundary conditions, which allowed an ice crystal growth that was nearly orthogonal to the external temperature gradient. Thereby, the preferential alignment of collagen fibres in the natural meniscus tissue could be mimicked. Those scaffolds owned appropriate sizes for cell culture in well plates or even an authentic meniscus shape and size. Finally, osteochondral scaffolds, sized to either fit well plates or perfusion reactors for cell culture, were fabricated to mimic the composition of subchondral bone and different cartilage zones. Collagen I and the resorbable calcium phosphate brushite were used for the subchondral zone, whereas the cartilage zones were composed out of collagen I, collagen II and tissue mimetic contents of GAGs. The pore structure corresponded to the one that is dominating the volume of natural osteochondral tissue. Energy dispersive X-ray spectroscopy (EDX) and SEM were used to analyse the composition and pore structure of the individual scaffold zones, respectively. The cross section pore diameters were determined to (65 ± 25) µm, (88 ± 35) µm and(93 ± 42) µm for the anisotropic, the isotropic and GAG containing isotropic bone scaffolds. Furthermore, the meniscus scaffolds showed pore diameters of (93 ± 21) µm in the inner meniscus zone and (248 ± 63) µm inside the outer meniscus zone. Pore sizes of (82 ± 25) µm, (83 ± 29) µm and (85 ± 39) µm were present inside the subchondral, the lower chondral and the upper chondral zone of osteochondral scaffolds. Depending on the fabrication parameters, the respective scaffold zones were also found to feature a specific micro- and nanostructure at their inner surfaces. Degradation studies were carried out under physiological conditions and resulted in a mean mass loss of (0.52 ± 0.13) \%, (1.56 ± 0.10) \% and (0.80 ± 0.10) \% per day for bone, meniscus and osteochondral scaffolds, respectively. Rheological measurements were used to determine the viscosity changes upon cooling of different precursors. Micro computer tomography (µ-CT) investigations were applied to characterize the 3D microstructure of osteochondral scaffolds. To obtain an osteochondral scaffold with four zones of tissue mimetic microstructure alignment, a poly (D, L-lactide-co-glycolide) mesh was deposited on the upper chondral zone by electrostatic spinning. In case of the bone scaffolds, the retention / release capacity of bone morphogenetic protein 2 (BMP-2) was evaluated by an enzyme linked immunosorbent assay (ELISA). Due to the high presence of attractive BMP binding sites, only less than 0.1 \% of the initially loaded cytokine was released. The suitability of combining the cryostructuring process with 3D powder printed calcium phosphate substrates was evaluated with osteochondral scaffolds, but did not appear to yield more preferable results than the non-combined approach. A new custom build confined compression setup was elaborated together with a suitable evaluation procedure for the mechanical characterisation under physiological conditions. For bone and cartilage scaffolds, apparent elastic moduli of (37.6 ± 6.9) kPa and (3.14 ± 0.85) kPa were measured. A similar behaviour of the scaffolds to natural cartilage and bone tissue was demonstrated in terms of elastic energy storage. Under physiological frequencies, less than 1.0 \% and 0.8 \% of the exerted energy was lost for bone and cartilage scaffolds, respectively. With average relaxation times of (0.613 ± 0.040) sec and (0.815 ± 0.077) sec, measured for the cartilage and bone scaffolds, they respond four orders of magnitude faster than the native tissues. Additionally, all kinds of produced scaffolds were able to withstand cyclic compression at un-physiological frequencies as high as 20 Hz without a loss in structural integrity. With the presented new method, scaffolds could be fabricated whose extent in mimicking of native tissues exceeded the one of scaffolds producible by state of the art methods. This allowed a testing of the key hypothesis: The biological evaluation of an anisotropic pore structure in vivo revealed a higher functionality of immigrated cells and led finally to advantageous healing outcomes. Moreover, the mimicking of local compositions in combination with a consecutive anisotropic porosity that approaches native tissue structures could be demonstrated to induce zone specific matrix remodelling in stem cells in vitro. Additionally, clues for a zone specific chondrogenic stem cell differentiation were attained without the supplementation of growth factors. Thereby, the hypothesis that an increased approximation of the hierarchically compositional and structurally anisotropic properties of musculoskeletal tissues would lead to an improved cellular response and a better healing quality, could be confirmed. With a special focus on cell free in situ tissue engineering approaches, the insights gained within this thesis may be directly transferred to clinical regenerative therapies.},
  subject      = {Tissue Engineering},
  language  = {en}
}
@phdthesis{Schmitz2016,
  author    = {Schmitz, Michael},
  title     = {Functional hydrophilic polymers for chemoselective coupling},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-145629},
  school      = {Universit{\"a}t W{\"u}rzburg},
  year      = {2016},
  abstract  = {Chemoselective poly(oxazolines) (POx) and poly[(oligo ethylene glycol) acrylates] were synthesized. An initiator was produced for the preparation of poly(oxazoline)s capable of participating in click chemistry reactions which allows the functionalization of the polymer at the α terminus which was confirmed by 1H NMR spectroscopy. The initiator was used for the polymerization of hydrophilic 2 methyl 2 oxazoline (MeOx), whereby chemoselective, alkyne functionalized polymers could be prepared for Cu-catalyzed azide-alkyne cycloaddition. The desired molecular weight could be achieved through the living, ring opening cationic polymerization and was confirmed by 1H NMR, SEC and MALDI ToF measurements. Polymers were terminated with piperidine if no further functionalization was needed, or with an ester derivate for enabling amine attachment in a subsequent step. In addition, polymers were functionalized by termination with NaN3 in order to provide the counterpart to the azide-alkyne reaction. IR spectroscopy was suitable for the azide detection. The coupling of polymers showed the reactivity and could be confirmed by SEC, 1H NMR and IR spectroscopy. The composition of cysteine functionalized POx was completed by thiol-ene chemistry. Since the commercially available iso 2 propyl 2 oxazoline is not available for the cationic polymerization, 2 butenyl and 2 decenyl 2 oxazoline (ButenOx and DecenOx) were first prepared. The synthesis of both copolymers, based on MeOx could be confirmed by 1H NMR as well as with SEC, whereby narrow distributions with dispersities of 1.06 could be achieved. The cysteine functionalization of the copolymers was enabled by the creation of a thiazolidine component which could be synthesized by acetal and formyl protection of cysteine and subsequent functionalization with a thiol. The component enabled the reaction with a polymer by thiol-ene reaction which was started by the addition of dimethoxyphenyl-acetophenone and was catalyzed by irradiation with UV light. Both copolymers, with a shorter (polymers with BuenOx) and longer (polymers with DecenOx) hydrophobic sidechain could be functionalized. 1H NMR spectroscopic analysis showed a quantitative reaction with the thiazolidine derivate. After deprotection by acidic workup the desired, cysteine functionalized polymer could be isolated. Quantification of cysteine functions was ensured by a modified TNBSA assay, whereby the thiols were first oxidized in order to confirm an independent measurement of amine functions. Both, the TNBSA assay as well as the NMR measurement showed the desired number of cysteine residues. The cytotoxicity of functionalized polymers with different compositions was tested by a luminescent cell viability assay (LCVA). Both, the amount of cysteine functions (5-10\%) in the copolymers as well as the length of the hydrophobic side chain were varied. All polymers did not show cytotoxicity up to concentrations of 10 mg∙mL-1. The cell activity and cell numbers only decreased below 50\% and 20\% respectively, when copolymers with 5\% cysteine and longer sidechains were measured, which was attributed to a contamination of the sample itself. The cooperation partner performed Native Chemical Ligation (NCL) with model peptides and purified the products by HPLC. A sterically non demanding peptide was synthesized, consisting of an aromatic amino acid and four glycine units. The aromatic unit was used for the quantification of the polymer-peptide conjugate in the 1H NMR spectroscopy. A polymer having five cysteine side chains has been fully implemented by NCL to a conjugate of one polymer with five peptides. A sterically more demanding peptide was additionally used and MALDI ToF measurements confirmed the successful conjugation. Furthermore the cysteine functionalized polymer was used for nanogel synthesis. The thiol of the cysteine function was oxidized in an inverse mini-emulsion by H2O2, resulting in nanogels (~500 nm) which could be confirmed by SEM, AFM, DLS and NTA measurements. Besides POx, oligo (ethylene glycol)acrylates (OEGA) were polymerized; by copolymerization with the reactive pentafluorophenyl acrylate (PFPA) reactive and amphiphilic polymers were obtained. The synthesis of PFPA could be confirmed spectroscopically by 1H , 19F NMR, and by FT IR. Copolymers were synthesized by RAFT polymerization with narrow dispersities. Functionalization with an amine functionalized thiazolidine led to a hydrophilic cysteine functionalized polymer after acidic deprotection. Apart from this polymer, a thioester functionalization was successfully performed by reaction of the active polymer with a cyclic amine functionalized thioester which does not release a toxic by product (such as the resulting thiol) during NCL and thus features a very high potential to replace former thioester.},
  subject      = {Konjugate},
  language  = {en}
}
@article{WeigandBoosTasbihietal.2016,
  author    = {Weigand, Annika and Boos, Anja M. and Tasbihi, Kereshmeh and Beier, Justus P. and Dalton, Paul D. and Schrauder, Michael and Horch, Raymund E. and Beckmann, Matthias W. and Strissel, Pamela L. and Strick, Reiner},
  title     = {Selective isolation and characterization of primary cells from normal breast and tumors reveal plasticity of adipose derived stem cells},
  series = {Breast Cancer Research},
  volume    = {18},
  journal   = {Breast Cancer Research},
  number    = {32},
  doi       = {10.1186/s13058-016-0688-2},
  url       = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-164759},
  year      = {2016},
  abstract  = {Background There is a need to establish more cell lines from breast tumors in contrast to immortalized cell lines from metastatic effusions in order to represent the primary tumor and not principally metastatic biology of breast cancer. This investigation describes the simultaneous isolation, characterization, growth and function of primary mammary epithelial cells (MEC), mesenchymal cells (MES) and adipose derived stem cells (ADSC) from four normal breasts, one inflammatory and one triple-negative ductal breast tumors. Methods A total of 17 cell lines were established and gene expression was analyzed for MEC and MES (n = 42) and ADSC (n = 48) and MUC1, pan-KRT, CD90 and GATA-3 by immunofluorescence. DNA fingerprinting to track cell line identity was performed between original primary tissues and isolates. Functional studies included ADSC differentiation, tumor MES and MEC invasion co-cultured with ADSC-conditioned media (CM) and MES adhesion and growth on 3D-printed scaffolds. Results Comparative analysis showed higher gene expression of EPCAM, CD49f, CDH1 and KRTs for normal MEC lines; MES lines e.g. Vimentin, CD10, ACTA2 and MMP9; and ADSC lines e.g. CD105, CD90, CDH2 and CDH11. Compared to the mean of all four normal breast cell lines, both breast tumor cell lines demonstrated significantly lower ADSC marker gene expression, but higher expression of mesenchymal and invasion gene markers like SNAI1 and MMP2. When compared with four normal ADSC differentiated lineages, both tumor ADSC showed impaired osteogenic and chondrogenic but enhanced adipogenic differentiation and endothelial-like structures, possibly due to high PDGFRB and CD34. Addressing a functional role for overproduction of adipocytes, we initiated 3D-invasion studies including different cell types from the same patient. CM from ADSC differentiating into adipocytes induced tumor MEC 3D-invasion via EMT and amoeboid phenotypes. Normal MES breast cells adhered and proliferated on 3D-printed scaffolds containing 20 fibers, but not on 2.5D-printed scaffolds with single fiber layers, important for tissue engineering. Conclusion Expression analyses confirmed successful simultaneous cell isolations of three different phenotypes from normal and tumor primary breast tissues. Our cell culture studies support that breast-tumor environment differentially regulates tumor ADSC plasticity as well as cell invasion and demonstrates applications for regenerative medicine.},
  language  = {en}
}