@phdthesis{Li2015, author = {Li, Han}, title = {Fabrication of Carbon Nanotube Thin Films by Evaporation-Induced Self-Assembly}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-123407}, school = {Universit{\"a}t W{\"u}rzburg}, pages = {159}, year = {2015}, abstract = {In summary, we have prepared single-wall carbon nanotube (SWNT) thin films by the method of evaporation-induced self-assembly (EISA). Using the scalable two-plate or lens setups, sorts of different film types or patterns of SWNTs has been successfully fabricated directly from the evaporation of solvents and could be precisely controlled by the concentrations of SWNT in ambient conditions. The special geometry of meniscus as the capillary bridge has not only given rise to a much higher efficiency of fabrication than what previously reported but also allowed us to monitor the pinning and depinning process carefully and further investigate the mechanism underlying the formation of different film morphologies. In contrast with the conventional "stick-slip" model, we have provided the new dynamical pinning and zipping model for the contact line (CL) behavior. By analyzing the motion of CL and varying deposited patterns, the traditionally so-called "stick" state should be treated as a dynamical pinning process due to the interfacial tension contrast between SWNT-covered and bare silicon surface. Besides, the plausible one-step "slip" motion could be dominated by the zipping-like kink propagation. In addition, the experiments with heated substrates at higher temperatures between 30°C and 50 °C have shown that the striped pattern could be fabricated by both much lower SWNT and SDS concentrations than that in room temperature, which is consistent with our model of interfacial tension contrast. In this situation, the deposition rate was increased but the quality of SWNT alignment was undermined because the corresponding moving velocity of SWNT was also too fast for SWNTs to rotate when the evaporative rate was high. The similar results were identified by the SWNT/polymer conjugates dispersed in chloroform under the similar setups and other identical conditions. The typical breathing motion of dynamical pinning and zipping-like propagation for depinning were confirmed by the new suspensions despite that some morphological parameters changed dramatically compared with that from the aqueous solution. For example, the spacing between stripes reached 100 µm ~ 200 µm because the large contact angle contrast between HDMS- and SWNT-covered surface accompanies with the high evaporation rate of chloroform in the pinning and depinning process. Likewise the average CL velocity for fabrication reached around 20 µm/s due to the much higher evaporation rate of chloroform than water. Using alike suspensions, the modified EISA method called dose-controlled floating evaporative self-assembly (DFES) was employed to implement the self-assembly of SWNTs on the water/air interface and then deposit them on solid substrate by directed floating. Although the stripes were fabricated successfully by drops with certain doses and SWNT concentrations, there inevitably existed randomly oriented SWNTs from the water surface that built networks between the stripes containing well-aligned tubes. In order to slow down the evaporation rate and monitor the process detailedly, we used chlorobenzene as the solvent instead of chloroform and find the typical pinning/depinning movement of the CL. A preliminary analysis of the results in terms of chlorobenzene implied that the CL possibly followed the similar pinning/depinning process in consistence with our model with capillary bridge. In the last part of the thesis, the primary research on the optical properties of these stripes of ultrahigh purity semiconducting nanotubes was conducted by fluorescence microscopy and photoluminescence excitation (PLE) spectroscopy. The energy transfer of the photogenerated excitons was confirmed between different tube species with controlled band gaps. In short, the experiments performed in this thesis allowed to gain new insights about the fabrication of large-area SWNT thin films by the cost-effective solution-processed method and most importantly to uncover its intrinsic mechanism as well. Combined with the separation and selection technique like density gradient centrifugation or polyfluorene derivatives assisted method, highly monodisperse semiconducting nanotubes could be deposited into organized, controllable and functional arrays. Beyond the ambient conditions, precise control for the evaporation under preset temperature and vapor pressure could possibly extend the technique to the industry level. Assisted by some other mature techniques such as roll-to-roll printing, the cost-effective method could be widely used in the manufacture of various thin film devices. More complex 2D or even 3D structures could be designed and accomplished by the method for the functional or stretchable requirements. Further research on the fundamental exciton transition and diffusion in different networks or structures of SWNTs will be the significant precondition for the real applications. Looking ahead, from the individual carbon nanotube to its thin film, this promising material with outstanding properties had many challenges to overcome before the real-world applications. Thanks to the availability of pure and well-defined materials, the scalable solution-processed approaches for fabrication of thin films should be able to unlock the potential of carbon nanotubes and exploit them in (opto-)electronic devices in the foreseeing future.}, subject = {Kohlenstoff-Nanor{\"o}hre}, language = {en} } @article{FiedlerElKarehEremeevetal.2014, author = {Fiedler, Sebastian and El-Kareh, Lydia and Eremeev, Sergey V. and Tereshchenko, Oleg E. and Seibel, Christoph and Lutz, Peter and Kokh, Konstantin A. and Chulkov, Evgueni V. and Kuznetsova, Tatyana V. and Grebennikov, Vladimir I. and Bentmann, Hendrik and Bode, Matthias and Reinert, Friedrich}, title = {Defect and structural imperfection effects on the electronic properties of BiTeI surfaces}, series = {New Journal of Physics}, volume = {16}, journal = {New Journal of Physics}, number = {075013}, issn = {1367-2630}, doi = {10.1088/1367-2630/16/7/075013}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-119467}, year = {2014}, abstract = {The surface electronic structure of the narrow-gap seminconductor BiTeI exhibits a large Rashba-splitting which strongly depends on the surface termination. Here we report on a detailed investigation of the surface morphology and electronic properties of cleaved BiTeI single crystals by scanning tunneling microscopy, photoelectron spectroscopy (ARPES, XPS), electron diffraction (SPA-LEED) and density functional theory calculations. Our measurements confirm a previously reported coexistence of Te- and I-terminated surface areas originating from bulk stacking faults and find a characteristic length scale of ~100 nm for these areas. We show that the two terminations exhibit distinct types of atomic defects in the surface and subsurface layers. For electronic states resided on the I terminations we observe an energy shift depending on the time after cleavage. This aging effect is successfully mimicked by depositon of Cs adatoms found to accumulate on top of the I terminations. As shown theoretically on a microscopic scale, this preferential adsorbing behaviour results from considerably different energetics and surface diffusion lengths at the two terminations. Our investigations provide insight into the importance of structural imperfections as well as intrinsic and extrinsic defects on the electronic properties of BiTeI surfaces and their temporal stability.}, language = {en} } @article{BrueningWehnerHausneretal.2016, author = {Br{\"u}ning, Christoph and Wehner, Johannes and Hausner, Julian and Wenzel, Michael and Engel, Volker}, title = {Exciton dynamics in perturbed vibronic molecular aggregates}, series = {Structural Dynamics}, volume = {3}, journal = {Structural Dynamics}, doi = {10.1063/1.4936127}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-126085}, pages = {043201}, year = {2016}, abstract = {A site specific perturbation of a photo-excited molecular aggregate can lead to a localization of excitonic energy. We investigate this localization dynamics for laser-prepared excited states. Changing the parameters of the electric field significantly influences the exciton localization which offers the possibility for a selective control of this process. This is demonstrated for aggregates possessing a single vibrational degree of freedom per monomer unit. It is shown that the effects identified for the molecular dimer can be generalized to larger aggregates with a high density of vibronic states.}, language = {en} } @phdthesis{Spaeth2015, author = {Sp{\"a}th, Florian Leonhard}, title = {Pr{\"a}paration und Charakterisierung einwandiger Kohlenstoffnanorohr-Polyfluoren-Komplexe}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-123874}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Im Fokus dieser Arbeit standen (6,5)-SWNT-PFO-BPy-Komplexe als Vertreter f{\"u}r polyfluorenstabilisierte, einwandige Kohlenstoffnanor{\"o}hren. In einem ersten Projekt wurden pr{\"a}parative Verfahren zur Dispergierung und Abscheidung dieser Proben weiterentwickelt. Es ist gelungen, die Ansatzgr{\"o}ße von 15 mL auf 200 mL hochzuskalieren sowie d{\"u}nne SWNT-Filme {\"u}ber Rotationsbeschichtung herzustellen. Des Weiteren wurde die lichtinduzierte Dynamik in halbleitenden SWNTs von der ps- bis zur µs-Zeitskala untersucht. Hier wurde ein umfassendes Bild zur Singulett- und Triplett-Exzitonendynamik in halbleitenden Kohlenstoffnanor{\"o}hren gezeichnet, welches maßgeblich durch diffusionslimitierte Prozesse gepr{\"a}gt ist. Abschließend wurde eine Methode vorgestellt, mit der sich Informationen zur Struktur von SWNT-Polymer-Komplexen und anderen supramolekularen Systemen gewinnen lassen. Diese basiert auf der Kombination von polarisationswinkelaufgel{\"o}ster Absorptionsspektroskopie an anisotropen Proben und globaler Datenanalyse.}, subject = {Kohlenstoff-Nanor{\"o}hre}, language = {de} } @phdthesis{Bergler2015, author = {Bergler, Felix}, title = {Photolumineszenzbasierte Untersuchung der Struktur und der thermodynamischen Bildungsparameter mizellar stabilisierter (6,5)-Kohlenstoffnanor{\"o}hren}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-123586}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {In dieser Arbeit werden die Wechselwirkungen zwischen der Oberfl{\"a}che von Kohlenstoffnanor{\"o}hren und verschiedenen Dispergierreagenzien anhand der Photolumineszenz (PL) der (6,5)-Nanor{\"o}hren untersucht. Um den Einfluss der verschiedenen Reagenzien auf die exzitonischen Eigenschaften und die PL-Emission zu quantifizieren, wurden die Dispergierreagenzien ausgetauscht, die Temperaturabh{\"a}ngigkeit bestimmt und die Konzentration der Reagenzien variiert. Die Dispergierreagenzien eines immobilisierten, SC-stabilisierten (6,5)-SWNT-Ensembles wurden im Mikrofluidikkanal ausgetauscht. Wird der Kanal mit Wasser gesp{\"u}lt, verringern sich die PL-Intensit{\"a}t und die Emissionsenergie, da der Wasserfluss die Tensidmolek{\"u}le von der Oberfl{\"a}che entfernt. Beim Austausch einer DOC-Umgebung gegen Wasser nimmt die PL-Intensit{\"a}t ebenfalls ab und die PL-Emissionsenergie verringert sich. Die Austauschexperimente verlaufen reversibel und der instantane Anstieg der Emissionsenergie bei der Tensidadsorption weist auf eine kooperative Anlagerung hin. Deshalb ist anzunehmen, dass sich Tensid-SWNT-Heteromizellen ausbilden. Anschließend werden die Emissionsenergie und die PL-Intensit{\"a}t in verschiedenen Dispergierreagenzien und in Wasser verglichen. Die gr{\"o}ßte Emissionsenergie und PL-Intensit{\"a}t werden w{\"a}hrend des Wechsels von einer SDS- zu einer (GT)16-L{\"o}sung gemessen. Dies kann auf die l{\"u}ckenlose Bedeckung der SWNT-Oberfl{\"a}che mit einer heterogenen Schicht aus SDS-Molek{\"u}len und (GT)16-Str{\"a}ngen zur{\"u}ckgef{\"u}hrt werden. In reiner SDS-Umgebung emittieren die Nanor{\"o}hren Licht mit der zweith{\"o}chsten Energie, aber die PL-Intensit{\"a}t liegt unter der in einer SC-Umgebung. Die Emissionsenergie in der SC-Umgebung ist geringer und davon abh{\"a}ngig, ob die SWNTs bereits mit (GT)16-Str{\"a}ngen stabilisiert waren, da dies eine permanente Rotverschiebung der Emissionsenergie in der SC-Umgebung sowie eine verringerte PL-Intensit{\"a}t verursacht. In w{\"a}ssriger Umgebung verringert sich nach erfolgtem (GT)16-Kontakt die PL-Intensit{\"a}t dauerhaft. Danach wurde die Anlagerung von Tensidmolek{\"u}len an die (6,5)-SWNT-Oberfl{\"a}che in Suspensionen mit der Temperatursprungmethode untersucht. Die Temperatur im Mikrofluidikkanal wurde anhand der linearen Abnahme der Emissionsenergie SC- und DOC-stabilisierter SWNTs mit steigender Temperatur bestimmt. Die Suspensionstemperatur ist in den verschiedenen Temperatursprungexperimenten unabh{\"a}ngig von der Messposition im Mikrofluidikkanal und wird durch die absolute Position auf den Peltier-Elementen bestimmt. Zudem stimmen die im Kanal gemessenen Temperaturen f{\"u}r SC- und DOC-stabilisierte (6,5)-SWNTs {\"u}berein, weshalb in diesem Experiment nicht die erwartete Einstellung eines Gleichgewichts wie in einem Temperatursprungexperiment der Fall, sondern die Momentantemperatur gemessen wird. Die schnelle Gleichgewichtseinstellung zwischen freien und auf der SWNT-Oberfl{\"a}che adsorbierten Tensidmolek{\"u}len beim Temperatursprung zeigt, dass die SC- und DOC-(6,5)-SWNT-Suspensionen thermochrome Farbstoffe sind. Wegen der Temperaturabh{\"a}ngigkeit der Emissionsenergie ist es bei wissenschaftlichen Arbeiten wichtig, neben dem verwendeten Dispergierreagenz auch die Temperatur der SWNT-Suspension anzugeben. Abschließend wurden die kritischen Mizellenkonzentrationen von Tensid-SWNT-Suspensionen in Verd{\"u}nnungsexperimenten und daraus die thermodynamischen Bildungsparameter der Tensid-SWNT-Heteromizellen ermittelt. In der temperaturabh{\"a}ngigen Analyse der SC-SWNT-Mizellenbildung wird ein konstanter Hill-Koeffizient erhalten, der die Mizellenbildung als positiv kooperativ klassifiziert. F{\"u}r die Bestimmung der Freien Mizellierungsenthalpie wurden nur die CMCs aus den Verd{\"u}nnungsexperimenten verwendet, da die Mizellenbildung bei der Aufkonzentration teils kinetisch gehemmt ist. Da die Freie Mizellierungsenthalpie bei allen Temperaturen negativ ist, stabilisiert die Bildung der Heteromizellen das System. Die Triebkraft f{\"u}r die Mizellenbildung ist {\"u}ber 322 K die Enthalpie, w{\"a}hrend unterhalb von 316 K der Entropiegewinn dominiert. Die Verd{\"u}nnung einer DOC-SWNT-Suspension zeigt keine {\"A}nderung der Emissionsenergie, obwohl dabei sowohl die prim{\"a}re als auch die sekund{\"a}re CMC von DOC unterschritten werden. Zuletzt wurden die Verd{\"u}nnungsexperimente mit einer SDS-SWNT-Suspension durchgef{\"u}hrt und die thermodynamischen Parameter der Mizellenbildung bestimmt. Da auf die Aufl{\"o}sung der Mizellenstruktur direkt die Aggregation der SWNTs folgt, wurde f{\"u}r die Ermittlung der CMC n{\"a}herungsweise die Konzentration am Maximum der Emissionsenergie verwendet. Daraus ergibt sich bei jeder Temperatur eine negative Freie Mizellierungsenthalpie, deren Beitr{\"a}ge analog zu SC bei kleineren Temperaturen als 323 K entropisch und bei h{\"o}heren Temperaturen enthalpisch dominiert werden. Somit erm{\"o}glichen die Experimente mit SC- und SDS-SWNT-Suspensionen die temperaturabh{\"a}ngige Bestimmung der CMC und damit die Berechnung der Freien Mizellierungsenthalpie sowie der zugeh{\"o}rigen enthalpischen und entropischen Beitr{\"a}ge.}, subject = {Kohlenstoff-Nanor{\"o}hre}, language = {de} } @phdthesis{Macher2021, author = {Macher, Sven}, title = {On the Effects of Moisture on Polymer-Based Electrochromic Devices}, doi = {10.25972/OPUS-24240}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-242407}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2021}, abstract = {The present work builds on a conjugated electrochromic polymer with a highly transmissive and colorless bright state and its application in electrochromic devices. The main body of this work focuses on the investigation of the influence of moisture on electrochromic devices and solutions to overcome possible degradation of these devices due to moisture ingress. Firstly, a series of EDOT derivatives with a terminal double bond in the lateral sidechain to potentially achieve a highly transmissive and fully colorless bright state was investigated. All of the EDOT derivatives were electrochemically polymerized and characterized by means of (in-situ) spectroelectrochemistry. The results highlight the dramatic influence of the terminal double bond on the improved visible light transmittance and color neutrality in the bright state. After detailed evaluation and comparison, the best performing compound, which contains a hexenyl sidechain (PEDOT-EthC6), was scaled-up by changing the deposition technique from an electrochemical to a chemical in-situ polymerization process on a R2R-pilot line in an industrially relevant environment. The R2R-processed PEDOTEthC6 half-cells were characterized in detail and provide enhanced electrochromic properties in terms of visible light transmittance and color neutrality in the bright state as well as short response times, improved contrast ratio, coloration efficiency and cycling stability (10 000 cycles).[21] In a second step, the novel PEDOT-EthC6 electrochromic polymer was combined with a Prussian Blue counter electrode and a solid polymer electrolyte to form an all-solid-sate ECDs based on complementary switching electrodes and PET-ITO as flexible substrates. The fabricated ECDs were optically and spectroelectrochemically characterized. Excellent functionality of the S2S-processed flexible ECDs was maintained throughout 10 000 switching cycles under laboratory conditions. The ECDs offer enhanced electrochromic properties in terms of visible light transmittance change and color neutrality in the bright state as well as contrast ratio, coloration efficiency, cycling stability and fast response times. Furthermore, the final device assembly was transferred from a S2S-process to a continuous R2R-lamination process.[238] In a third step, the PEDOT-EthC6/PB-based ECDs were submitted to conscious environmental aging tests. The emphasis of the research presented in this work, was mainly put at the influence of moisture and possible failure mechanisms regarding the PEDOT-EthC6/PB based ECDs. An intense brown coloration of the electrodes was observed while cycling the ECDs in humid atmospheres (90\% rH) as a major degradation phenomenon. The brown coloration and a thereby accompanied loss of conductivity of the PET-ITO substrates was related to significant degradation of the ITO layers, inserted as the conductive layers in the flexible ECDs. A dissolution of the ITO thin films and formation of metallic indium particles on the surface of the ITO layers was observed that harmed the cycling stability enormously. The conductive layers of the aged ECDs were investigated by XRD, UV-Vis, SEM and spectroelectrochemical measurements and validated the supposed irreversible reduction of the ITO layers.[279] In the absence of reasonable alternatives to PET-ITO for flexible (R2R-processed) ECDs, it is also important to investigate measures to avoid the degradation of ECDs. This is primarily associated with the avoidance of appropriate electrode potentials necessary for ITO reduction in humid atmospheres. As an intrinsic action point, the electrode potentials were investigated via electrochemical measurements in a three-electrode setup of an all-solid-state ECD. Extensive knowledge on the electrode potentials allowed the voltage-induced degradation of the ITO in flexible ECDs to be avoided through the implementation of an unbalanced electrode configuration (charge density ratio of working and counter electrode). It was possible to narrow the overall operational voltage window to an extent in which irreversible ITO reduction no longer occurs. The unbalanced electrode configuration lead to an improved cycling stability without harming other characteristics such as response time and light transmittance change and allows ECD operation in the presence of humidity.[279] The avoidance of the mentioned degradation phenomena is further associated with appropriate sealing methods and materials as well as appropriate electrode and device fabrication processes. Since a variety of sealing materials is commercially available, due to the commercial launch of organic photovoltaic (OPV) and light emitting diodes (OLEDs), the focus in the present work was put to water-free electrode fabrication. As an extrinsic action point, a novel preparation method of a nanoscale PEDOT-EthC6 dispersion based on organic solvents is presented here in a final step. The water-free processing method gives access to straightforward printing and coating processes on flexible PET-ITO substrates and thus represents a promising and simplified alternative to the established PEDOT:PSS. The resulting nano-PEDOT-EthC6 thin films exhibit enhanced color neutrality and transmissivity in the bright state and are comparable to the properties of the in-situ polymerized PEDOT-EthC6 thin films.[280]}, subject = {Elektrochromie}, language = {en} } @phdthesis{Mueller2022, author = {M{\"u}ller, Stefan}, title = {Coherent Multiple-Quantum Multidimensional Fluorescence Spectroscopy}, doi = {10.25972/OPUS-24411}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-244113}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {This thesis describes novel concepts for the measurement of the static and dynamic properties of the electronic structure of molecules and nanocrystals in the liquid phase by means of coherent fluorescence-detected spectroscopy in two and three frequency dimensions. These concepts are based on the systematic variation ("phase cycling") of a sequence of multiple time-delayed femtosecond excitation pulses in order to decode a multitude of novel nonlinear signals from the resulting phase-dependent fluorescence signal. These signals represent any permutation of correlations between zero-, one-, two-, and three-quantum coherences. To this end, two new phase-cycling schemes have been developed which can simultaneously resolve and discriminate several nonlinear signals of sixth order, including those of the fourth order of nonlinearity. By means of the sixth-order signals recorded in this work, static properties of highly excited electronic states in molecules such as their energies, transition dipole moments, and relative displacement of electronic potential surfaces, as well as dynamic properties in terms of their relaxation kinetics, can be ascertained. Furthermore, it was shown that these signals are suitable for the characterization of exciton-exciton correlations in colloidal quantum dots and for the measurement of ultrafast exciton-exciton annihilation in molecular aggregates. The experiments performed in this thesis mark an important step towards the complete characterization of the nonlinear response of quantum systems. In view of this, the concept of fluorescence-detected multiple-quantum coherence multidimensional spectroscopy introduced here offers a unified, systematic approach. In virtue of the technical advantages such as the use of a single excitation beam and the absence of nonresonant contributions, the measurement protocols developed here can be directly transferred to other incoherent observables and to sample systems in other states of matter. Furthermore, the approaches presented here can be systematically extended to higher frequency dimensions and higher orders of nonlinearity.}, subject = {Coherent Multidimensional Spectroscopy}, language = {en} } @phdthesis{Kess2016, author = {Keß, Martin}, title = {Wellenfunktionsbasierte Beschreibung der zweidimensionalen vibronischen Spektroskopie von molekularen Aggregaten und Ladungstransfersystemen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-136458}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2016}, abstract = {Diese Arbeit befasst sich mit zeitaufgel{\"o}sten Prozessen in molekularen Systemen. Dabei wurde sowohl die Wellenpaketdynamik nach Photoanregung betrachtet als auch spektrale Eigenschaften mittels Absorptions- und zweidimensionaler Spektroskopie untersucht. Zun{\"a}chst widmet sich die Arbeit der Wellenpaket- und Populationsdynamik in zwei diabatischen, gekoppelten Zust{\"a}nden. Nach impulsiver Anregung aus dem zu Beginn besetzten Zustand treten in der Populationsdynamik zwei deutlich verschiedene Oszillationen auf. Der langsamer variierende Populationstransfer besitzt die Periodendauer der Vibrationsbewegung und ist auf einen Wechsel der Zust{\"a}nde beim Durchlaufen des Wellenpakets durch die Kreuzungsregion der diabatischen Potentiale zur{\"u}ckzuf{\"u}hren. Die ultraschnelle Komponente mit einer Periodendauer von etwa 4 fs l{\"a}sst sich als eine Art Rabi-Oszillation beschreiben, die durch die (zeitunabh{\"a}ngige) Kopplung hervorgerufen wird. Sie wurde mit Hilfe von analytischen Berechnungen ausf{\"u}hrlich charakterisiert. Damit dieser Prozess auftreten kann m{\"u}ssen mehrere Bedingungen erf{\"u}llt werden: Das Wellenpaket muss {\"u}ber die Dauer der Oszillationen ann{\"a}hernd {\"o}rtlich lokalisiert bleiben; dies ist an den Umkehrpunkten der Wellenpaketsbewegung der Fall. Die Amplitude der Oszillationen in den Populationen ist proportional zum Verh{\"a}ltnis der Kopplung zum Energieabstand der Zust{\"a}nde. Deshalb muss an den station{\"a}ren Stellen die Kopplung groß im Vergleich zum Energieabstand sein. Die Amplitude der Oszillationen h{\"a}ngt außerdem von dem Populationsverh{\"a}ltnis und den Phasen der Komponenten des Wellenpakets in den beiden Zust{\"a}nden ab. Die ultraschnellen Oszillationen bleiben auch in mehrdimensionalen Systemen mit unterschiedlichen Vibrationsfrequenzen je Freiheitsgrad erhalten. Das gleiche Modell wurde benutzt, um Ladungstransferprozesse mittels linearer und 2D-Spektroskopie zu untersuchen. Eine Kopplung an die Umgebung wurde, aufbauend auf einer Quanten-Master-Gleichung in Markov-N{\"a}herung, wellenfunktionsbasiert mittels eines Quantum-Jump-Algorithmus mit expliziter Dephasierung beschrieben. Dabei findet mit vorher definierten Wahrscheinlichkeiten zu jedem Zeitschritt einer von drei stochastischen Prozessen statt. Neben koh{\"a}renter Propagation k{\"o}nnen Spr{\"u}nge in einen anderen Eigenzustand des Systems und Dephasierungen auftreten. Zwei Dissipationsparameter spielen dabei eine Rolle. Dies ist zum einen die St{\"a}rke der System-Bad-Kopplung, welche die Gesamtrate der Energierelaxation beschreibt. Weiterhin beeinflusst die Dephasierungskonstante den Verlust koh{\"a}renter Phasen ohne Energie{\"a}nderung. Fallenzust{\"a}nde wurden identifiziert, die durch sehr geringe Sprungraten in niedrigere Zust{\"a}nde charakterisiert sind. Die Langlebigkeit kann durch die Form der Eigenfunktionen erkl{\"a}rt werden, die eine deutlich andere Wahrscheinlichkeitsverteilung als die der Nicht-Fallenzust{\"a}nde besitzen. Dadurch werden die in die Sprungraten eingehenden Matrixelemente klein. Das Absorptionsspektrum zeigt Peaks an der Stelle der Fallenzust{\"a}nde, da nur die Eigenfunktionen der Fallenzust{\"a}nde große Franck-Condon-Faktoren mit der Anfangswellenfunktion besitzen. Verschiedene Kombinationen der Dissipationsparameter f{\"u}hren zu {\"A}nderungen der relativen Peakintensit{\"a}ten und der Peakbreiten. Die 2D-Spektren des Ladungstransfersystems werden st{\"o}rungstheoretisch {\"u}ber die Polarisation dritter Ordnung berechnet. Sie zeigen viele eng nebeneinander liegende Peaks in einer schachbrettmusterf{\"o}rmigen Anordnung, die sich auf {\"U}berg{\"a}nge unter Mitwirkung der Fallenzust{\"a}nde zur{\"u}ckf{\"u}hren lassen. H{\"o}here System-Bad-Kopplungen f{\"u}hren aufgrund der effizienten Energiedissipation zu einer Verschiebung zu kleineren Energien. Peaks, die mit schneller zerfallenden Fallenzust{\"a}nden korrespondieren, bleichen schneller aus. H{\"o}here Dephasierungskonstanten resultieren in verbreiterten Peaks. Um den Einfluss der Dissipation genauer zu charakterisieren, wurden gefilterte 2D-Spektren betrachtet. Dazu wurden Ausschnitte der Polarisation dritter Ordnung zu verschiedenen Zeiten fouriertransformiert. L{\"a}ngere Zeiten f{\"u}hren zu einer effektiveren Energierelaxation entlang der entsprechenden Zeitvariablen. Die Entv{\"o}lkerung der h{\"o}her liegenden Zust{\"a}nde l{\"a}sst sich somit zeit- und energieaufgel{\"o}st betrachten. Weiterhin wurde gezeigt, dass sich der Zerfall eines einzelnen Peaks mit dem Populationsabfall des damit korrespondierenden Eigenzustandes in Einklang bringen l{\"a}sst, obwohl die Zuordnung der Peaks im 2D-Spektrum zu {\"U}berg{\"a}ngen zwischen definierten Eigenzust{\"a}nden nicht eindeutig ist. Mit dem benutzten eindimensionalen Modell k{\"o}nnen auch Ladungstransferprozesse in organischen gemischtvalenten Verbindungen beschrieben werden. Es wurde die Frage untersucht, welche Prozesse nach einem optisch induzierten Energietransfer in solchen Systemen ablaufen. Experimentelle Daten (aufgenommen im Arbeitskreis von Prof. Lambert) deuten auf eine schnelle interne Konversion (IC) gefolgt von Thermalisierung hin. Um dies theoretisch zu {\"u}berpr{\"u}fen, wurden Absorptionsspektren bei verschiedenen Temperaturen berechnet und mit den gemessenen transienten Spektren verglichen. Es findet sich, abh{\"a}ngig von der St{\"a}rke der elektronischen Kopplung, eine sehr gute bis gute {\"U}bereinstimmung, was die Annahme eines schnellen ICs st{\"u}tzt. Im letzten Teil der Arbeit wurden vibronische 2D-Spektren von molekularen Aggregaten betrachtet. Dazu wurde die zeitabh{\"a}ngige Schr{\"o}dingergleichung f{\"u}r ein Monomer-, Dimer- und Trimersystem mit der Multi-Configuration Time-Dependent Hartree-Methode gel{\"o}st und die Polarisation nicht-st{\"o}rungstheoretisch berechnet. Der Hamiltonoperator des Trimers umfasst hierbei sieben gekoppelte elektronische Zust{\"a}nde und drei bzw. sechs Vibrationsfreiheitsgrade. Der betrachtete Photonenecho-Beitrag der Polarisation wurde mittels phasencodierter Laserpulse extrahiert. Die resultierenden Spektren sind geometrieabh{\"a}ngig, ein Winkel zwischen den {\"U}bergangsdipolmomenten der Monomere von 0° (180°) resultiert in einem H-Aggregat (J-Aggregat). Die Lage und Intensit{\"a}t der Peaks im rein elektronischen Trimer wurde analytisch erl{\"a}utert. Die Spektren unter Einbeziehung der Vibration zeigen eine ausgepr{\"a}gte vibronische Struktur. Es wurde gezeigt, wie die Spektren f{\"u}r h{\"o}here Aggregationsgrade durch die h{\"o}here Dichte an vibronischen Zust{\"a}nden komplexer werden. Im J-Aggregat ist mit zunehmender Aggregation eine st{\"a}rkere Rotverschiebung zu sehen. Das Spektrum des H-Aggregats zeigt eine im Vergleich zum J-Aggregat kompliziertere Struktur. Die Verwendung zweier Vibrationsfreiheitsgrade je Monomer f{\"u}hrt zu Spektren mit {\"u}berlappenden Peaks und einer zus{\"a}tzlichen vibronischen Progression. Der Vergleich von Spektren verschiedener Mischungen von Monomer, Dimer und Trimer, entsprechend einem von Temperatur und Konzentration abh{\"a}ngigen Aggregationsgrad, zeigt den Einfluss dieser experimentellen Faktoren. Schließlich wurden m{\"o}gliche Ans{\"a}tze aufgezeigt, anhand der Spektren auf den Aggregationsgrad zu schließen.}, subject = {Quantenmechanik}, language = {de} } @phdthesis{Koch2016, author = {Koch, Federico Juan}, title = {Structure-Dependent Ultrafast Relaxation Dynamics in Multichromophoric Systems}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-136306}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2016}, abstract = {Time-resolved spectroscopy allows for analyzing light-induced energy conversion and chromophore-chromophore interactions in molecular systems, which is a prerequisite in the design of new materials and for improving the efficiency of opto-electronic devices. To elucidate photo-induced dynamics of complex molecular systems, transient absorption (TA) and coherent two-dimensional (2D) spectroscopy were employed and combined with additional experimental techniques, theoretical approaches, and simulation models in this work. A systematic series of merocyanines, synthetically varied in the number of chromophores and subsitution pattern, attached to a benzene unit was investigated in cooperation with the group of Prof. Dr. Frank W{\"u}rthner at the University of W{\"u}rzburg. The global analysis of several TA experiments, and additional coherent 2D spectroscopy experiments, provided the basis to elaborate a relaxation scheme which was applicable for all merocyanine systems under investigation. This relaxation scheme is based on a double minimum on the excited-state potential energy surface. One of these minima is assigned to an intramolecular charge-transfer state which is stabilized in the bis- and tris-chromophoric dyes by chromphore-chromophore interactions, resulting in an increase in excited-state lifetime. Electro-optical absorption and density functional theory (DFT) calculations revealed a preferential chromophore orientation which compensates most of the dipole moment of the individual chromophores. Based on this structural assignment the conformationdependent exciton energy splitting was calculated. The linear absorption spectra of the multi-chromophoric merocyanines could be described by a combination of monomeric and excitonic spectra. Subsequently, a structurally complex polymeric squaraine dye was studied in collaboration with the research groups of Prof. Dr. Christoph Lambert and Prof. Dr. Roland Mitric at the University of W{\"u}rzburg. This polymer consists of a superposition of zigzag and helix structures depending on the solvent. High-level DFT calculations confirmed the previous assignment that zigzag and helix structures can be treated as J- and H-aggregates, respectively. TA experiments revealed that in dependence on the solvent as well as the excitation energy, ultrafast energy transfer within the squaraine polymer proceeds from initially excited helix segments to zigzag segments or vice versa. Additionally, 2D spectroscopy confirmed the observed sub-picosecond dynamics. In contrast to other conjugated polymers such as MEH-PPV, which is investigated in the last chapter, ultrafast energy transfer in squaraine polymers is based on the matching of the density of states between donor and acceptor segments due to the small reorganization energy in cyanine-like chromophores. Finally, the photo-induced dynamics of the aggregated phase of the conjugated polymer MEH-PPV was investigated in cooperation with the group of Prof. Dr. Anna K{\"o}hler at the University of Bayreuth. Our collaborators had previously described the aggregation of MEH-PPV upon cooling by the formation of so-called HJ-aggregates based on exciton theory. By TA measurements and by making use of an affiliated band analysis distinct relaxation processes in the excited state and to the ground state were discriminated. By employing 2D spectroscopy the energy transfer between different conjugated segments within the aggregated polymer was resolved. The initial exciton relaxation within the aggregated phase indicates a low exciton mobility, in contrast to the subsequent energy transfer between different chromophores within several picoseconds. This work contributes by its systematic study of structure-dependent relaxation dynamics to the basic understanding of the structure-function relationship within complex molecular systems. The investigated molecular classes display a high potential to increase efficiencies of opto-electronic devices, e.g., organic solar cells, by the selective choice of the molecular morphology.}, subject = {Femtosekundenspektroskopie}, language = {en} } @article{RudolfKanalGehrigetal.2013, author = {Rudolf, P. and Kanal, F. and Gehrig, D. and Niesel, J. and Brixner, T. and Schatzschneider, U. and Nuernberger, P.}, title = {Femtosecond mid-infrared study of the aqueous solution photochemistry of a CO-releasing molecule (CORM)}, series = {EPJ Web of Conferences}, volume = {41}, journal = {EPJ Web of Conferences}, doi = {10.1051/epjconf/20134105004}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-129104}, pages = {05004}, year = {2013}, abstract = {Ultraviolet irradiation of CO-releasing molecules (CORMs) in water eventually leads to the loss of several carbon monoxide ligands.We show for an exemplary manganese tricarbonyl CORM that only one ligand is photolyzed off on an ultrafast timescale and that some molecules may undergo geminate recombination.}, language = {en} } @article{RuetzelKullmannBubacketal.2013, author = {Ruetzel, S. and Kullmann, M. and Buback, J. and Nuernberger, P. and Brixner, T.}, title = {Exploring higher-lying electronic states of a molecular switch by coherent triggered-exchange 2D electronic spectroscopy}, series = {EPJ Web of Conferences}, volume = {41}, journal = {EPJ Web of Conferences}, number = {05001}, doi = {10.1051/epjconf/20134105001}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-129117}, year = {2013}, abstract = {We use pump-repump-probe transient absorption spectroscopy to investigate the role of higher-lying electronic states in the photochemistry of a molecular switch. Moreover, replacing the pump pulse by a pulse-shaper-generated phase-stable double pulse, triggered-exchange two-dimensional (TE2D) electronic spectroscopy is established in the visible regime.}, language = {en} } @article{SteinbacherBubackNuernbergeretal.2013, author = {Steinbacher, A. and Buback, J. and Nuernberger, P. and Brixner, T.}, title = {Precise and rapid detection of optical activity for accumulative femtosecond spectroscopy}, series = {EPJ Web of Conferences}, volume = {41}, journal = {EPJ Web of Conferences}, doi = {10.1051/epjconf/20134112011}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-129124}, pages = {12011}, year = {2013}, abstract = {We present a fast and sensitive polarimeter combining common-path optical heterodyne interferometry and accumulative spectroscopy to detect rotatory power. The sensitivity of rotatory detection is determined to be 0.10 milli-degrees for a measurement time of only one second and an interaction length of 250 µm. Its suitability for femtosecond studies is demonstrated in a non-resonant two-photon photodissociation experiment.}, language = {en} } @phdthesis{Knorr2015, author = {Knorr, Johannes Walter}, title = {Femtosecond spectroscopy of photolysis reactions in the liquid phase}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-131362}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Within the framework of this thesis, photolysis reactions in the liquid phase were investigated by means of ultrafast optical spectroscopy. Apart from molecular studies dealing with the highly spin-dependent reactivity of diphenylcarbene (DPC) in binary solvent mixtures and ligand dissociation reactions of so-called CO-releasing molecules (CORMs), special emphasis was put on the implementation and characterization of methods improving and extending the signal detection in conventional pump-probe transient absorption setups. The assumption of DPC being an archetypal triplet-ground-state arylcarbene was recently questioned by matrix-isolation studies at low temperatures. DPC embedded in argon matrices revealed a hitherto unknown reactivity when the carbene environment was modified by small amounts of methanol dopant molecules. To complement these findings with liquid-phase experiments at room temperature, femtosecond pump-probe transient absorption spectroscopy with probing in the visible and ultraviolet regime was employed to unravel primary reaction processes of DPC in solvent mixtures. Supported by quantum chemical simulations conducted by our collaborators, it was shown that a competition between the reaction pathways occurs that not only depends on the solvent molecule near-by but also on its interaction with other solvent molecules. In-depth analysis of the solvation dynamics and the amount of nascent intermediates corroborates the importance of a hydrogen-bonded complex with a protic solvent molecule, in striking analogy to complexes found at cryogenic temperatures. Probing the transient absorption of molecules in the mid-infrared spectral range benefits from the high chemical specificity of molecules' vibrational signatures. The technique of chirped-pulse upconversion (CPU) constitutes a promising alternative to standard direct multichannel MCT detection when accessing this spectral detection window. Hence, one chapter of this thesis is dedicated to a direct comparison between both detection methods. By conducting an exemplary pump-probe transient absorption experiment, it became evident, that the additional nonlinear interaction step is responsible for increased noise levels when using CPU. However, a correction procedure capable of removing these additional noise contributions—stemming from the fundamental laser radiation used for upconversion—was successfully tested. Perhaps most importantly for various spectroscopic applications, CPU scored with a significantly extended detection bandwidth owing to the high pixel numbers of modern CCD cameras. Transition-metal complexes capable of releasing small molecular messengers upon photoactivation are promising sources of gasotransmitters such as carbon monoxide (CO) or nitric oxide (NO) in biological applications. However, only little is known about the characteristic time scales of ligand dissociation in this class of molecules. For this purpose, two complexes were investigated with femtosecond time resolution: [Mn(CO)3(tpm)]Cl with tpm=tris(2-pyrazolyl)methane, a manganese tricarbonyl complex which has proven to be selective and cytotoxic to cancer cells, and [Mo(CO)2(NO)(iPr3tacn)]PF6 with iPr3tacn=1,4,7-triisopropyl-1,4,7-triazacyclononane, a molybdenum complex containing both carbonyl and nitrosyl ligands. By conducting pump-probe transient absorption measurements in different spectral probing windows supported by quantum chemical calculations and linear absorption spectroscopy, it was shown that both complexes are able to release one CO ligand within the first few picoseconds after UV excitation. The results complement existing studies which focused on the molecules' ligand-releasing properties upon long-term exposure. The additional information gained on an ultrafast time scale provides a comprehensive understanding of individual reaction steps connected with ligand release in this class of molecules. Hence, the studies might create new incentives to develop modified molecules for specific applications.}, subject = {Ultrakurzzeitspektroskopie}, language = {en} } @article{ArcaTeddeSrameketal.2013, author = {Arca, Francesco and Tedde, Sandro F. and Sramek, Maria and Rauh, Julia and Lugli, Paolo and Hayden, Oliver}, title = {Interface Trap States in Organic Photodiodes}, series = {Scientific Reports}, volume = {3}, journal = {Scientific Reports}, doi = {10.1038/srep01324}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-131507}, pages = {1324}, year = {2013}, abstract = {Organic semiconductors are attractive for optical sensing applications due to the effortless processing on large active area of several \(cm^2\), which is difficult to achieve with solid-state devices. However, compared to silicon photodiodes, sensitivity and dynamic behavior remain a major challenge with organic sensors. Here, we show that charge trapping phenomena deteriorate the bandwidth of organic photodiodes (OPDs) to a few Hz at low-light levels. We demonstrate that, despite the large OPD capacitances of similar to 10 nF \(cm^{-2}\), a frequency response in the kHz regime can be achieved at light levels as low as 20 nW \(cm^{-2}\) by appropriate interface engineering, which corresponds to a 1000-fold increase compared to state-of-the-art OPDs. Such device characteristics indicate that large active area OPDs are suitable for industrial sensing and even match medical requirements for single X-ray pulse detection in the millisecond range.}, language = {en} } @phdthesis{Ansorg2015, author = {Ansorg, Kay}, title = {Development of Accurate Physically Grounded Force Fields for Intermolecular Cation-\$\pi\$ Interactions based on SAPT Energy Decomposition Analysis and Computational Investigation of Covalent Irreversible Vinyl Sulfone-based Protease Inhibitors}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-131084}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Part 1 of this work describes the development of accurate physically grounded force fields for intermolecular Cation-π interactions based on SAPT energy decomposition analysis. The presented results demonstrate the benefits of the used DFT-SAPT method to describe non-bonding interactions. First of all, this method is able to reproduce the high level CCSD(T) energy values but using much less computational time. Second it provides the possibility to separate the total intermolecular interaction energy into several physically meaningful contributions. The relative contributions of the dimers investigated can be seen in Fig. 6.16. In Tab. 6.3 the percentage contribution of the attractive energy parts to the stabilization energy is shown. The polarization energy is important for the NH+...C6H6 interaction, whereas it becomes less crucial considering other dimers. The dispersion energy contribution is large in the case of the C6H6...H2O dimers, whereas it is relatively less important for the NH+...C6H6 interaction. The electrostatic energy contributes a large amount of stabilizing energy in all considered dimer interactions. ...}, subject = {Kraftfeld}, language = {en} } @article{BrixnerAeschlimannFischeretal.2013, author = {Brixner, T. and Aeschlimann, M. and Fischer, A. and Geisler, P. and Goetz, S. and Hecht, B. and Huang, J. S. and Keitzl, T. and Kramer, C. and Melchior, P. and Pfeiffer, W. and Razinskas, G. and Rewitz, C. and Schneider, C. and Str{\"u}ber, C. and Tuchscherer, P. and Voronine, D. V.}, title = {Coherent spectroscopies on ultrashort time and length scales}, series = {EPJ Web of Conferences}, volume = {41}, journal = {EPJ Web of Conferences}, doi = {10.1051/epjconf/20134109017}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-129073}, pages = {09017}, year = {2013}, abstract = {Three spectroscopic techniques are presented that provide simultaneous spatial and temporal resolution: modified confocal microscopy with heterodyne detection, space-time-resolved spectroscopy using coherent control concepts, and coherent two-dimensional nano-spectroscopy. Latest experimental results are discussed.}, language = {en} } @phdthesis{Steinbacher2015, author = {Steinbacher, Andreas Edgar}, title = {Circular dichroism and accumulative polarimetry of chiral femtochemistry}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-116500}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {This work brings forward successful implementations of ultrafast chirality-sensitive spectroscopic techniques by probing circular dichroism (CD) or optical rotation dispersion (ORD). Furthermore, also first steps towards chiral quantum control, i.e., the selective variation of the chiral properties of molecules with the help of coherent light, are presented. In the case of CD probing, a setup capable of mirroring an arbitrary polarization state of an ultrashort laser pulse was developed. Hence, by passing a left-circularly polarized laser pulse through this setup a right-circularly polarized laser pulse is generated. These two pulse enantiomers can be utilized as probe pulses in a pump--probe CD experiment. Besides CD spectroscopy, it can be utilized for anisotropy or ellipsometry spectroscopy also. Within this thesis, the approach is used to elucidate the photochemistry of hemoglobin, the oxygen transporting protein in mammalian blood. The oxygen loss can be triggered with laser pulses as well, and the results of the time-resolved CD experiment suggest a cascade-like relaxation, probably through different spin states, of the metallo-porphyrins in hemoglobin. The ORD probing was realized via the combination of common-path optical heterodyne interferometric polarimetry and accumulative femtosecond spectroscopy. Within this setup, on the one hand the applicability of this approach for ultrafast studies was demonstrated explicitly. On the other hand, the discrimination between an achiral and a racemic solution without prior spatial separation was realized. This was achieved by inducing an enantiomeric excess via polarized femtosecond laser pulses and following its evolution with the developed polarimeter. Hence, chiral selectivity was already achieved with this method which can be turned into chiral control if the polarized laser pulses are optimized to steer an enhancement of the enantiomeric excess. Furthermore, within this thesis, theoretical prerequisites for anisotropy-free pump--probe experiments with arbitrary polarized laser pulses were derived. Due to the small magnitude of optical chirality-sensitve signals, these results are important for any pump--probe chiral spectroscopy, like the CD probing presented in this thesis. Moreover, since for chiral quantum control the variation of the molecular structure is necessary, the knowledge about rearrangement reactions triggered by photons is necessary. Hence, within this thesis the ultrafast Wolff rearrangement of an α-diazocarbonyl was investigated via ultrafast photofragment ion spectroscopy in the gas phase. Though the compound is not chiral, the knowledge about the exact reaction mechanism is beneficial for future studies of chiral compounds.}, subject = {Ultrakurzzeitspektroskopie}, language = {en} } @phdthesis{Hain2015, author = {Hain, Tilman Christian}, title = {Entwicklung eines experimentellen Aufbaus zur Charakterisierung nanoskaliger Systeme mittels Fluoreszenzspektroskopie und -mikroskopie}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-116618}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Die vorliegende Dissertation leistet einen Beitrag zur spektroskopischen Messmethodik nanoskaliger Strukturen. Im Mittelpunkt der Arbeit steht die Entwicklung und Erprobung eines spektrofluorimetrischen Aufbaus, mit dessen Hilfe ein aus Kohlenstoffnanor{\"o}hren und DNA-Oligomeren bestehendes supramolekulares Modellsystem einer optischen Untersuchung zug{\"a}nglich gemacht wird. Die Vielseitigkeit der Messeinheit aus Mikroskop und Spektrometer wird an einer weiteren Substanzklasse untermauert. So wird das Emissionsverhalten von in Siliziumcarbidkristallen induzierten Defektzentren einer r{\"a}umlich, spektral und zeitlich aufgel{\"o}sten Charakterisierung unterzogen. Die zentrale Komponente des Spektrofluorimetrieaufbaus stellt eine Superkontinuumlichtquelle dar. In Verbindung mit einem elektronisch geregelten Filtermodul zur Wellenl{\"a}ngenselektion erlaubt sie die Durchf{\"u}hrung von Photolumineszenz-Anregungsexperimenten. Im Gegensatz zu kommerziell erh{\"a}ltlichen Systemen, die {\"u}berwiegend auf eine spektroskopische Charakterisierung gel{\"o}ster oder kolloidal stabilisierter Substanzen abzielen, erlaubt der hier realisierte Aufbau auch die PL- mikroskopische Untersuchung kondensierter Proben, was durch die Epi-Bauweise auch opake Substrate einschließt. Der Einsatz von InGaAs-Sensoren weitet das Detektionsfenster auf den Nahinfrarotbereich aus, sowohl hinsichtlich des Kamera- als auch des Spektroskopiekanals. Anhand verschiedenartiger Kohlenstoffnanorohrproben, die entweder in fl{\"u}ssiger Phase dispergiert oder in festem Zustand als Film abgeschieden vorliegen, wird die Leistungsf{\"a}higkeit des PLE-Experiments unter Beweis gestellt. Neben der Zuordnung der Chiralit{\"a}ten in polydispersen SWNT-Suspensionen wird dies auch durch die Untersuchung von Energietransferprozessen und die Studie von Umgebungseinfl{\"u}ssen demonstriert. Die Charakterisierung des DNA-SWNT-Modellsystems in mikrofluidischer Umgebung macht von der fluoreszenzmikroskopischen Detektionseinheit Gebrauch. W{\"a}hrend die intrinsische Photolumineszenz der Nanor{\"o}hren sicherstellen soll, dass Letztere in ausreichender Anzahl auf den mikrostrukturierten Substraten vorhanden sind, wird die extrinsische Photolumineszenz der funktionalisierten Oligonukleotide als spektroskopisches Maß f{\"u}r die DNA-Konzentration herangezogen. Das hierbei beobachtete Agglomerationsverhalten der farbstoffmarkierten Oligomere geht mit einer lokal erh{\"o}hten Fluoreszenzintensit{\"a}t einher und erlaubt damit die quantitative Auswertung der auf PL-Einzelbildern basierenden Zeitserien. Zugleich wird damit eine Absch{\"a}tzung der DNA-Belegung auf den Nanor{\"o}hren m{\"o}glich. Im Falle der aus 16 alternierenden Guanin-Thymin-Einheiten bestehenden Basensequenz l{\"o}sen sich nach Initiieren des Desorptionsvorgangs ein Großteil der Oligomere von der Nanorohroberfl{\"a}che ab. Lediglich ein F{\"u}nftel bleibt in adsorbierter Form zur{\"u}ck, was sich jedoch f{\"u}r die Hybridstabilit{\"a}t als ausreichend erweist. Die Freisetzung weiterer Oligomere bleibt bei der Versuchstemperatur von 20 °C trotz der hohen Verd{\"u}nnung aus, da aufgrund des gr{\"o}ßeren Interadsorbatabstands und der damit verbundenen Abnahme repulsiver Wechselwirkungen die Aktivierungsbarriere f{\"u}r ihre Desorption steigt. Die Stabilit{\"a}t der DNA-SWNT-Konjugate liegt demnach in ihrer kinetischen Inertheit begr{\"u}ndet, die sie vor einer Reaggregation bewahrt. Die Studie der in Siliziumcarbid induzierten Fehlstellendefekte kann als Beleg f{\"u}r die breite Anwendbarkeit des spektrofluorimetrischen Aufbaus gelten. PL-Mikroskopaufnahmen zeigen hierbei, dass die Anzahl der Defektzentren mit der Bestrahlungsintensit{\"a}t kontrolliert werden kann - von einer kontinuierlichen Verteilung bei hohen Strahlungsintensit{\"a}ten {\"u}ber heterogene Defektansammlungen bis hin zu Einzeldefektstellen bei niedrigen Strahlungsdosen. Letztere resultieren in beugungsbegrenzten Signaturen und erlauben damit eine Charakterisierung des abbildenden Systems sowie des Anregungsfokus. Anhand der PLE-Analyse l{\"a}sst sich das Absorptionsmaximum absch{\"a}tzen. Aussagen zur zeitlichen Entwicklung des Emissionsverhaltens werden durch TCSPC-Messungen erhalten. Die abschließende Untersuchung des Photonenflusses mit Hilfe von Korrelationsexperimenten nach Hanbury Brown-Twiss zeigt bei Raumtemperatur kein Auftreten von Photonantibunching.}, subject = {Fluoreszenzspektroskopie}, language = {de} } @phdthesis{Hartleb2015, author = {Hartleb, Holger Edgar Heinz Erich}, title = {Spektroelektrochemische Untersuchung von halbleitenden Kohlenstoffnanor{\"o}hren}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-116628}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Der Schwerpunkt dieser Arbeit lag auf der spektroelektrochemischen Untersuchung von halbleitenden SWNTs. Hierbei wurden erstmalig Absorptions- und Photolumineszenzspektren ein und derselben SWNT-Probe simultan unter elektrochemischer Potentialkontrolle aufgenommen. Hierbei konnte gezeigt werden, dass die Messmethode einen entscheidenden Einfluss auf die erhaltene Bandl{\"u}cke besitzt und der in der Literatur gepr{\"a}gte Begriff der Elektrochemischen Bandl{\"u}cke aufgrund einer fehlenden allgemeing{\"u}ltigen Definition problembehaftet ist. So ergeben Photolumineszenzmessungen im Vergleich zu Raman- oder Absorptionsmessungen die kleinste Bandl{\"u}cke. Dies wurde auf die diffusionskontrollierte L{\"o}schung der Exzitonen an Ladungszentren zur{\"u}ckgef{\"u}hrt. Weiterhin wurden die optischen Spektren von SWNTs unter Ladungseinfluss analysiert und die zugrundeliegenden {\"A}nderungen der elektronischen Eigenschaften diskutiert. Neben SWNTs wurden die {\"U}bergangsmetalldichalkogenide MoS2 und WS2 spektroelektrochemisch untersucht. Auffallend im Vergleich zu den Messungen an SWNTs war der breite Potentialbereich, {\"u}ber den die Abnahme der exzitonischen Signale zu beobachten war. Dies kann auf die unterschiedliche elektronische Struktur von TMDs und SWNTs und den geringen Anteil von Einzellagen in den TMD-Proben zur{\"u}ckgef{\"u}hrt werden. Weiterhin konnte in den Absorptionsspektren unter Ladungseinfluss ein Signal beobachtet werden, welches auf die Entstehung von Trionen hindeutet. In einem weiteren Teilprojekt wurde eine elektrochemische Zelle zur Untersuchung von metallischen SWNT-Filmen als Elektrode f{\"u}r die Wasserstoffproduktion entwickelt und getestet. Hierbei gelang es die von Das et al. publizierte Aktivierung von SWNTs mit Schwefels{\"a}ure erfolgreich nachzuvollziehen und einen katalytischen Effekt der SWNTs auf die Wasserstoffentwicklung zu beobachten.}, subject = {Kohlenstoff-Nanor{\"o}hre}, language = {de} } @phdthesis{Mann2015, author = {Mann, Christoph}, title = {Exzitonengr{\"o}ße und -dynamik in (6,5)-Kohlenstoffnanor{\"o}hren : Transiente Absorptions- und Photolumineszenzmessungen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-116712}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Zahlreiche theoretische und experimentelle Untersuchungen haben erwiesen, dass in halbleitenden Kohlenstoffnanor{\"o}hren durch Absorption von Licht haupts{\"a}chlich Exzitonen erzeugt werden. Die photophysikalischen Eigenschaften und insbesondere die Prozesse nach der optischen Anregung sind aber gegenw{\"a}rtig noch nicht vollst{\"a}ndig verstanden. Zeitaufgel{\"o}ste Spektroskopie bietet die M{\"o}glichkeit, diese Prozesse zu verfolgen und somit detaillierten Einblick in das photophysikalische Verhalten von Kohlenstoffnanor{\"o}hren zu nehmen. Hierbei scheinen auch extrinsische Faktoren - zu nennen sind die Herstellungsmethode, die Art der Probenpr{\"a}paration, der Aggregationsgrad sowie der durch das L{\"o}sungs- bzw. Dispersionsmittel bedingte Einfluss - eine entscheidende Rolle zu spielen. In dieser Dissertation wurden die Exzitonengr{\"o}ße sowie die exzitonische Dynamik in einwandigen Kohlenstoffnanor{\"o}hren mittels transienter Absorptionsspektroskopie sowie station{\"a}rer und zeitaufgel{\"o}ster Photolumineszenzmessungen untersucht. Alle Experimente fanden dabei an halbleitenden (6,5)-Kohlenstoffnanor{\"o}hren statt, deren chirale Anreicherung durch Dichtegradientenultrazentrifugation gelang. F{\"u}r die temperaturabh{\"a}ngigen Messungen wurde ein Verfahren zur Herstellung von tensidstabilisierten Gelatinefilmen entwickelt. Diese zeichnen sich durch eine hohe Temperaturstabilit{\"a}t bei gleichzeitiger Minimierung von Streulichteffekten aus. Die Bestimmung der Exzitonengr{\"o}ße erfolgte mit Hilfe des Phasenraumf{\"u}llmodells, das die intensit{\"a}tsabh{\"a}ngige {\"A}nderung der Oszillatorst{\"a}rke eines {\"U}bergangs mit der Exzitonengr{\"o}ße verkn{\"u}pft. Hierf{\"u}r wurden leistungsabh{\"a}ngige Messungen der transienten Absorption durchgef{\"u}hrt und die Signalintensit{\"a}t des Photobleichens gegen die absorbierte Photonenflussdichte aufgetragen. Da diese beiden Gr{\"o}ßen nur bei geringer Exzitonendichte in einer linearen Beziehung stehen, aus der sich die Exzitonengr{\"o}ße berechnen l{\"a}sst, wurde im Experiment besonderer Wert auf niedrige Anregungsfluenzen und deren exakte Bestimmung gelegt. Um den Einfluss der Aggregation quantifizieren zu k{\"o}nnen und den Vergleich mit der Literatur zu erleichtern, fanden die Untersuchungen sowohl an individualisierten als auch an aggregierten R{\"o}hrenproben statt. Die Datenanalyse, bei der erstmalig die stimulierte Emission sowie der spektrale {\"U}berlapp von Photoabsorptions- und Photobleichbande Ber{\"u}cksichtigung fanden, ergab f{\"u}r individualisierte (6,5)-Nanor{\"o}hren einen Wert von 12.0 nm f{\"u}r die Gr{\"o}ße des S1-Exzitons, w{\"a}hrend diese bei der aggregierten R{\"o}hrenprobe nur 5.6 nm betr{\"a}gt. Die Probenabh{\"a}ngigkeit der Exzitonengr{\"o}ße macht den Vergleich mit anderen experimentell ermittelten Werten schwierig. Diese liegen fast ausschließlich zwischen 1 nm und 4.5 nm, ihre Bestimmung fand aber teilweise an stark aggregierten bzw. polydispersen Proben statt. Theoretische Berechnungen liefern f{\"u}r die Exzitonengr{\"o}ße Werte zwischen 1 nm und 4 nm. Zwar gelten einige der Berechnungen f{\"u}r Vakuum, was verglichen zu einer experimentell in L{\"o}sung bzw. im Film bestimmten Exzitonengr{\"o}ße einen kleineren Wert mit sich bringt, jedoch kann allein hierdurch die Diskrepanz zu der in dieser Arbeit ermittelten Exzitonengr{\"o}ße von 12.0 nm nicht erkl{\"a}rt werden. Setzt man experimentell und theoretisch f{\"u}r Vakuum bestimmte Werte f{\"u}r die Exzitonengr{\"o}ße und die Bindungsenergie in einen einfachen Zusammenhang, entspricht eine Exzitonengr{\"o}ße von 12.0 nm einer Bindungsenergie zwischen 0.21 eV und 0.27 eV. Die mittels Zweiphotonenexperimenten ermittelten Werte f{\"u}r die Bindungsenergie von (6,5)-Kohlenstoffnanor{\"o}hren befinden sich zwischen 0.37 eV und 0.42 eV; diese wurden allerdings unter Zuhilfenahme eines vereinfachten zylindrischen Modells abgesch{\"a}tzt. Weitere experimentelle und theoretische Untersuchungen k{\"o}nnten kl{\"a}ren, inwieweit eine exzitonische Bindungsenergie zwischen 0.21 eV und 0.27 eV f{\"u}r (6,5)-SWNTs in Betracht kommt. Strahlender und nichtstrahlender Zerfall in den Grundzustand scheinen in (6,5)-Kohlenstoffnanor{\"o}hren durch eine Dynamik zwischen verschiedenen Zust{\"a}nden sowie durch die Diffusion der Exzitonen beeinflusst zu werden. Um diese f{\"u}r die Rekombination maßgeblichen Prozesse besser zu verstehen, wurden temperaturabh{\"a}ngige Messungen der station{\"a}ren und zeitaufgel{\"o}sten Photolumineszenz sowie der transienten Absorption durchgef{\"u}hrt. Die Ergebnisse der station{\"a}ren PL-Experimente deuten darauf hin, dass die Exzitonen zwischen dem optisch aktiven Singulettzustand mit A2-Symmetrie - im Folgenden mit [B] bezeichnet - und einem energetisch tiefer liegenden dunklen Zustand [D] gestreut werden. Mit einem Wert von 5 meV f{\"u}r die energetische Aufspaltung zwischen [B] und [D] gelingt eine gute Anpassung an die Daten, was mit Blick auf die Bandstruktur von (6,5)-SWNTs vermuten l{\"a}sst, dass es sich bei [D] um den A1-Singulettzustand handelt. Außerdem scheint eine nichtthermische Verteilung der Exzitonen auf [B] und [D] vorzuliegen, wobei strahlende Rekombination nur vom Zustand [B] aus m{\"o}glich ist. Mit diesen Annahmen kann das temperaturabh{\"a}ngige Verhalten der station{\"a}ren Photolumineszenz modelliert werden, die Ergebnisse der zeitaufgel{\"o}sten PL-Messungen jedoch nicht. Mit einem rein diffusionsdominierten Modell gelingt dies ebenso wenig, so dass zur Interpretation des PL-Zerfalls vermutlich ein Modell entwickelt werden muss, in dem sowohl die Streuung der Exzitonen zwischen [B] und [D] als auch das durch Diffusion bedingte L{\"o}schen an Defektstellen oder R{\"o}hrenenden Ber{\"u}cksichtigung findet. Die Bedeutung der Diffusion von Exzitonen zu Defektstellen oder R{\"o}hrenenden, an denen bevorzugt nichtstrahlender Zerfall stattfindet, kann durch spektral- und zeitaufgel{\"o}ste PL-Messungen belegt werden. Abh{\"a}ngig von der zur Verf{\"u}gung stehenden thermischen Energie und der H{\"o}he der Potenzialbarrieren des untersuchten Systems kann die Diffusion niederenergetischer Exzitonen, die sich in Potenzialminima befinden, soweit eingeschr{\"a}nkt werden, dass diese eine fast bis um den Faktor zwei l{\"a}ngere PL-Lebensdauer aufweisen als h{\"o}herenergetische Exzitonen. Das unterschiedliche Verhalten von transienter Absorption und zeitaufgel{\"o}ster Photolumineszenz bei Temperaturen zwischen 14 K und 35 K zeigt, dass die Repopulation des Grundzustands haupts{\"a}chlich von einem anderen Zustand aus erfolgt als die strahlende Rekombination. Ob es sich hierbei aber um den mit [D] bezeichneten A1-Singulettzustand oder einen anderen dunklen Zustand handelt, kann nicht abschließend gekl{\"a}rt werden. Aufgrund inhomogener Verbreiterung stellt die Halbwertsbreite der Banden im Absorptionsspektrum ein Maß f{\"u}r die H{\"o}he der Potenzialbarrieren bzw. f{\"u}r die energetische Verteilung der Exzitonen im angeregten Zustand dar. In dieser Arbeit wurde anhand vier verschiedener Nanorohrsuspensionen gezeigt, dass S{\"a}ttigungsverhalten der transienten Absorption von (6,5)-Kohlenstoffnanor{\"o}hren und Bandenbreite im Absorptionsspektrum demselben Trend folgen. Begr{\"u}nden kann man dies damit, dass das S{\"a}ttigungsverhalten der transienten Absorption durch Exziton-Exziton-Annihilation bestimmt wird. Aufgrund ihrer eindimensionalen Struktur unterliegen Kohlenstoffnanor{\"o}hren einer starken Beeinflussung durch die Umgebung. Abh{\"a}ngig vom L{\"o}sungs- bzw. Dispersionsmittel resultiert eine unterschiedliche inhomogene Verbreiterung der Absorptionsbanden und damit unterschiedlich hohe Potenzialbarrieren im angeregten Zustand. Niedrige Potenzialbarrieren erlauben eine weitreichende Diffusion der Exzitonen, sodass effiziente Exziton-Exziton-Annihilation schon bei einer vergleichsweise geringen Exzitonendichte stattfindet und das Signal der transienten Absorption bei einer niedrigen Impulsfluenz s{\"a}ttigt.}, subject = {Exziton}, language = {de} } @phdthesis{Renziehausen2014, author = {Renziehausen, Klaus}, title = {Wechselwirkung von Molek{\"u}len mit Laserpulsen: Untersuchungen zur numerischen Implementierung zeitabh{\"a}ngiger St{\"o}rungstheorie und zu Effekten der absoluten Phase von Laserpulsen beliebiger L{\"a}nge}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-100850}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {In dieser Dissertation wurden zwei Aspekte der Wechselwirkung von Laserpulsen mit Molek{\"u}len betrachtet: Erstens wurden numerische Algorithmen, die auf der zeitabh{\"a}ngigen St{\"o}rungstheorie basieren, zur Berechnung von quantenmechanischen Wellenfunktionen analysiert. Zweitens wurden Effekte der absoluten Phase (Carrier envelope phase = CEP) von Laserpulsen bei der Laseranregung molekularer Systeme analysiert. In den Analysen zum ersten Aspekt wurden zwei verschiedene Algorithmen - in dieser Arbeit als simple und improved algorithm bezeichnet - verwendet, und die Normabweichung von mit diesen Algorithmen berechneten Wellenfunktionen untersucht. Es konnte gezeigt werden, dass diese Normabweichung f{\"u}r beide Algorithmen in zwei unterschiedliche Beitr{\"a}ge zerlegt werden kann. Der erste Normabweichungsbeitrag tritt aufgrund der numerischen Diskretisierung der Zeit auf und verschwindet, wenn der Zeitschritt, der die Dauer der Intervalle f{\"u}r diese Diskretisierung angibt, gegen Null geht. Man kann den ersten Normabweichungsbeitrag mit exzellenter Genauigkeit berechnen und seine Eigenschaften, die sich f{\"u}r die beiden Algorithmen erheblich unterschieden, eingehend analysieren. Der zweite Normabweichungsbeitrag tritt dadurch auf, dass die zeitabh{\"a}ngige St{\"o}rungstheorie nicht normerhaltend ist, und geht daher gegen Null, wenn die St{\"o}rungsordnung gegen unendlich geht. Dieser zweite Beitrag ist außerdem in guter N{\"a}herung unabh{\"a}ngig vom Zeitschritt und f{\"u}r beide Algorithmen n{\"a}herungsweise gleich. Des Weiteren kann man das Verhalten des zweiten Normabweichungsbeitrags im Gegensatz zum ersten Beitrag nur qualitativ beschreiben. F{\"u}r die Analyse zum zweiten Themengebiet dieser Arbeit, den CEP-Effekten, wurde betrachtet, ob CEP-Effekte auch f{\"u}r Laserpulse beliebiger L{\"a}nge auftreten k{\"o}nnen. {\"U}ber eine analytische Betrachtung erkennt man, dass dies f{\"u}r ein Zweiniveausystem nur dann der Fall ist, wenn beide Zust{\"a}nde vor Beginn der Wechselwirkung des Systems mit dem Laserpuls besetzt sind. Man kann aus diesem Ergebnis folgern, dass f{\"u}r einen Laserpuls, der zwei elektronische Zust{\"a}nde eines Molek{\"u}ls {\"u}ber Einphotonen{\"u}berg{\"a}nge koppelt, in der Regel kein CEP-Effekt f{\"u}r beliebige L{\"a}ngen dieses Pulses auftritt. Der Grund daf{\"u}r ist, dass vor der Wechselwirkung eines molekularen Systems mit einem Laserpuls f{\"u}r dieses {\"u}blicherweise nur der elektronische Grundzustand besetzt ist. In dieser Arbeit wird gezeigt, dass dieses Problem durch ein spezielles Zweipulsschema f{\"u}r die Anregung eines molekularen Systems gel{\"o}st werden kann. F{\"u}r dieses Pulsschema wird ein erster Puls verwendet, der zeitlich so kurz ist, dass Wellenpakete in mehreren elektronischen Zust{\"a}nden angeregt werden. Der nachfolgende zweite Laserpuls ist spektral schmal, und seine zeitliche L{\"a}nge kann beliebig groß gew{\"a}hlt werden. Man erh{\"a}lt f{\"u}r dieses Pulsschema Observablen, die von der CEP des zweiten Pulses, aber nicht von der CEP des ersten Pulses abh{\"a}ngen; somit ist ein CEP-Effekt nachweisbar. Derartige Observablen sind geometrische Asymmetrien f{\"u}r Zerfallsprodukte von Photodissoziationsreaktionen. Insbesondere unterscheidet sich das hier vorgestellte Pulsschema von anderen Zweipulsschemata, f{\"u}r welche Observablen von der Differenz der CEPs beider Pulse abh{\"a}ngen, aber nicht von der CEP einer der beiden Pulse allein.}, subject = {St{\"o}rungstheorie}, language = {de} } @phdthesis{Giegerich2015, author = {Giegerich, Jens}, title = {Velocity-Map-Imaging Studien an reaktiven Intermediaten: Fulvenallen, C3H2 Isomere und Alkylradikale}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-114982}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {In der vorliegenden Dissertation wurde die Photodissoziationsdynamik einer Reihe reaktiver Intermediate mittels Velocity-Map-Imaging Spektroskopie untersucht. Diese sind vor allem im Kontext von Verbrennungsprozessen sowie der Chemie im interstellaren Raum von Interesse. Die wichtigsten Erkenntnisse dieser Arbeit sollen nun kurz zusammengefasst werden. Fulvenallen stellt einen wichtigen Verzweigungspunkt in der Verbrennung von Toluol dar. Die Photodissoziationsdynamik von Fulvenallen, welches pyrolytisch aus Phthalid generiert wurde, konnte im Wellenl{\"a}ngenbereich von 245 - 255 nm aufgekl{\"a}rt werden. Dabei ist die ermittelte Dissoziationsrate (kH ≈ 107 s-1) in guter {\"U}bereinstimmung mit der mittels RRKM vorhergesagten Rate. In VMI-Experimenten zeigten die, durch Photodissoziation abstrahierten, Wasserstoffatome eine isotrope Winkelverteilung, wobei diese einen Anteil an der {\"U}berschussenergie von = 0:09 in Form von kinetischer Energie besaßen. Die Photodissoziation von Fulvenallen erfolgt statistisch ohne nennenswerte R{\"u}ckbarriere. Sowohl Winkel- als auch Energieverteilung sprechen f{\"u}r den folgenden Dissoziationsmechanismus: Fulvenallen wird durch ein Photon in den D1A1 Zustand angeregt, aus dem es durch interne Konversion schnell in den elektronischen Grundzustand relaxiert, aus dem es anschließend in einem statistischen Prozess dissoziiert. Spezies der Zusammensetzung C3H2 wurden im interstellaren Raum und in Flammenexperimenten beobachtet. In dieser Arbeit wurden zwei Isomere, Propargylen und Cyclopropenyliden, untersucht. Die Photodissoziation von Propargylen wurde bei einer Anregungswellenl{\"a}nge von 250 nm untersucht. In den VMI-Experimenten wurden Wasserstoffatome mit einem Erwartungswert der kinetischen Energie von = 0.53 eV beobachtet, was einem Anteil an der {\"U}berschussenergie von = 0.48 entspricht. Diese von Propargylen abstrahierten H-Atome waren trotz der hohen Translationsenergie mit einem Anisotropieparameter von = -0.05 nur leicht anisotrop verteilt. Durch den Vergleich mit quanten-klassischen Dynamik Simulationen ließ sich folgendes Bild der Dissoziation gewinnen: Propargylen wird mit 250 nm in den sechsten angeregten Triplett-Zustand T6 angeregt. Die anschließende Dissoziation ist direkt und erfolgt in ca. 200 fs aus T4 - T6. Der geringe Anisotropiegrad wurde durch einen Dissoziationsprozess erkl{\"a}rt, bei dem µT und die gebrochene C-H Bindung ann{\"a}hernd im magischen Winkel zueinander angeordnet sind. Die Photodissoziation von Cyclopropenyliden wurde bei einer Anregungswellenl{\"a}nge von 271 nm untersucht. Dabei wurden die Experimente an zwei unterschiedlichen Radikalvorl{\"a}ufern, 3-Chlorcyclopropen und einem Quadricyclanderivat, durchgef{\"u}hrt. Diese f{\"u}hrten im Wesentlichen zu denselben Ergebnissen. Die VMI-Experimente zeigen, dass in der Photodissoziation von Cyclopropenyliden die H{\"a}lfte der {\"U}berschussenergie in die Translation der Wasserstoffatome fließt (= 0:50). Aus der Winkelverteilung der abstrahierten Wasserstoffatome ergab sich eine isotrope Verteilung ( = 0). Der Vergleich mit quantendynamischen Simulationen erlaubt folgende Aussagen {\"u}ber den Dissoziationsmechanismus: Cyclopropenyliden wird mit einem Photon mit 271 nm in den zweiten angeregten Singulett-Zustand angeregt. Durch zwei konische Durchschneidungen relaxiert es in den elektronischen Grundzustand. Dabei kann die zyklische Struktur aufgebrochen und ein lineares Isomer gebildet werden. Die Berechnungen sagen ein Verh{\"a}ltnis cyklischer zu offenkettiger Struktur (Bruch der C=C Doppelbindung) von ca. 75 : 20 voraus. Die Dissoziation erfolgt ann{\"a}hernd ideal statistisch aus dem elektronischen Grundzustand. F{\"u}r beide Isomere ergab sich eine sehr gute {\"U}bereinstimmung zwischen Theorie und Experiment. Alkylradikale spielen ebenfalls eine wichtige Rolle in der interstellaren und der Verbrennungschemie und k{\"o}nnen als prototypische offenschalige Systeme angesehen werden. In der vorliegenden Arbeit wurde die Photodissoziationsdynamik des i-Propyl- und des t-Butylradikals untersucht und die Ergebnisse mit fr{\"u}heren VMI-Studien am Ethylradikal verglichen. Die Translationsenergieverteilung der in der Photodissoziation erzeugten H-Atome ist f{\"u}r alle drei Radikale bimodal. Dabei sind die Wasserstoffatome, welche ihr Maximum in der Translationsenergieverteilung bei niedrigen kinetischen Energien erreichen, isotrop verteilt. Die H-Atome mit hoher kinetischer Energie sind anisotrop verteilt. Aus dem Vergleich mit {\"a}lteren Arbeiten wurde ein m{\"o}glicher Dissoziationsmechanismus f{\"u}r die Alkylradikale erarbeitet. Dieser basiert auf Rydberg-Valenz-Wechselwirkungen und kann beide beobachteten Wasserstoffatomkan{\"a}le erkl{\"a}ren. Außerdem kann damit ein m{\"o}glicher C-C Bindungsbruch und die Bildung eines Methylradikals erkl{\"a}rt werden, welche f{\"u}r t-Butyl in der Literatur bereits beobachtet wurde. F{\"u}r eine solide theoretische Basis sind jedoch weitere umfassende quantenchemische und quantendynamische Studien erforderlich. Methyliodid z{\"a}hlt, was die Photodissoziation anbelangt, zu den am besten untersuchten Molek{\"u}len. Die in dieser Arbeit durchgef{\"u}hrten VMI-Experimente bez{\"u}glich der Photodissoziation von Methyliodid dienten in erster Linie als Kalibrierexperimente der Apparatur f{\"u}r schwerere Massen als Wasserstoff. Dabei zeigten die Experimente eine qualitativ gute {\"U}bereinstimmung mit fr{\"u}heren Studien, wodurch die Kalibrierparameter ermittelt werden konnten. Außerdem wurde die große Absorption bei 266 nm genutzt um die neue Photolysequelle in Betrieb zu nehmen. Damit ist es zuk{\"u}nftig m{\"o}glich, pyrolytisch nicht zug{\"a}ngliche Radikale, wie z.B. Radikale, deren ungepaartes Elektron an einem Sauerstoffatom lokalisiert ist, zu erzeugen. Des Weiteren wurden pyrolytisch und photolytisch erzeugte freie Radikale miteinander verglichen. Dabei zeigte sich, dass die Photolyse Radikale mit geringerer interner Energie generiert, wobei die Pyrolyse eine deutlich h{\"o}here Konversionseffizienz besitzt. Aufgenommene Images bei unterschiedlichen Pyrolyseleistungen erlaubten die Absch{\"a}tzung der effektiven Temperatur des Molekularstrahls. Diese Erkenntnis ist besonders im Hinblick auf die Diskussion zuk{\"u}nftiger Pyrolyseexperimente interessant.}, subject = {Photodissoziation}, language = {de} } @article{KanalKeiberEcketal.2014, author = {Kanal, Florian and Keiber, Sabine and Eck, Reiner and Brixner, Tobias}, title = {100-kHz shot-to-shot broadband data acquisition for high-repetition-rate pump-probe spectroscopy}, doi = {10.1364/OE.22.016965}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-112853}, year = {2014}, abstract = {Shot-to-shot broadband detection is common in ultrafast pump-probe spectroscopy. Taking advantage of the intensity correlation of subsequent laser pulses improves the signal-to-noise ratio. Finite data readout times of CCD chips in the employed spectrometer and the maximum available speed of mechanical pump-beam choppers typically limit this approach to lasers with repetition rates of a few kHz. For high-repetition (≥ 100 kHz) systems, one typically averages over a larger number of laser shots leading to inferior signal-to-noise ratios or longer measurement times. Here we demonstrate broadband shot-to-shot detection in transient absorption spectroscopy with a 100-kHz femtosecond laser system. This is made possible using a home-built high-speed chopper with external laser synchronization and a fast CCD line camera. Shot-to-shot detection can reduce the data acquisition time by two orders of magnitude compared to few-kHz lasers while keeping the same signal-to-noise ratio.}, language = {en} } @article{BrixnerPawłowskaGoetzetal.2014, author = {Brixner, Tobias and Pawłowska, Monika and Goetz, Sebastian and Dreher, Christian and Wurdack, Matthias and Krauss, Enno and Razinskas, Gary and Geisler, Peter and Hecht, Bert}, title = {Shaping and spatiotemporal characterization of sub-10-fs pulses focused by a high-NA objective}, doi = {10.1364/OE.22.031496}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-111120}, year = {2014}, abstract = {We describe a setup consisting of a 4 f pulse shaper and a microscope with a high-NA objective lens and discuss the spects most relevant for an undistorted spatiotemporal profile of the focused beam. We demonstrate shaper-assisted pulse compression in focus to a sub-10-fs duration using phase-resolved interferometric spectral modulation (PRISM). We introduce a nanostructure-based method for sub-diffraction spatiotemporal characterization of strongly focused pulses. The distortions caused by optical aberrations and space-time coupling from the shaper can be reduced by careful setup design and alignment to about 10 nm in space and 1 fs in time.}, language = {en} } @article{KnorrRudolfNuernberger2013, author = {Knorr, Johannes and Rudolf, Philipp and Nuernberger, Patrick}, title = {A comparative study on chirped-pulse upconversion and direct multichannel MCT detection}, doi = {10.1364/OE.21.030693}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-111334}, year = {2013}, abstract = {A comparative study is carried out on two spectroscopic techniques employed to detect ultrafast absorption changes in the mid-infrared spectral range, namely direct multichannel detection via HgCdTe (MCT) photodiode arrays and the newly established technique of chirped-pulse upconversion (CPU). Whereas both methods are meanwhile individually used in a routine manner, we directly juxtapose their applicability in femtosecond pump-probe experiments based on 1 kHz shot-to-shot data acquisition. Additionally, we examine different phase-matching conditions in the CPU scheme for a given mid-infrared spectrum, thereby simultaneously detecting signals which are separated by more than 200 cm-1.}, language = {en} } @phdthesis{Hefner2014, author = {Hefner, Timo}, title = {Einfluss von Dispergierungsmethode und Rohmaterialaufreinigung auf die Beschaffenheit einwandiger Kohlenstoffnanorohrsuspensionen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-105839}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {In der vorliegenden Dissertation wurden Dispergierungseffizienz, Entb{\"u}ndelungseffizienz und R{\"o}hrenqualit{\"a}t von SWNT-Suspensionen untersucht. Die R{\"o}hrenqualit{\"a}t wurde durch Messung von Quantenausbeuten bewertet. Außerdem wurden Suspensionen von den drei verschiedenen Rohmaterialien CoMoCAT, Black Sand und HiPCO, hergestellt durch die Behandlung mit Ultraschall und Schermischen, verglichen. Beim Beschallen zeigte sich wie erwartet eine h{\"o}here Dispergierungseffizienz im Vergleich zum Schermischen. Diese war jeweils bei Black Sand am gr{\"o}ßten, gefolgt von CoMoCAT und HiPCO. Ein Vergleich zwischen zwei HiPCO-Materialien best{\"a}tigte die deutlichen Effizienzvorteile nicht aufgereinigter Materialien. Trotz der viel geringeren Dichte des aufgereinigten HiPCO-Materials, ließ sich dieses durch das Schermischen wesentlich schlechter dispergieren. Der Effizienzunterschied war jedoch geringer als bei Black Sand und CoMoCAT, was vermutlich auf den geringeren Unterschied der Kohlenstoffanteile zur{\"u}ckzuf{\"u}hren ist. Dieser wiederum h{\"a}ngt von den jeweiligen Herstellungs- und Aufreinigungsverfahren ab. Die Dispergierungsgeschwindigkeit war f{\"u}r gescherte Black Sand- und CoMoCAT-Proben zu Beginn der Dispergierung h{\"o}her als f{\"u}r die jeweils beschallten Proben, weshalb durch Kombination der beiden Methoden m{\"o}glicherweise eine Verbesserung der pr{\"a}parierten Suspensionen bez{\"u}glich der drei untersuchten Parameter erreicht werden kann. Der Vergleich der Entb{\"u}ndelungseffizienzen ergab erneut Vorteile beim Ultraschall gegen{\"u}ber dem Schermischen. Die beschallten Black Sand- und HiPCO-Proben zeigten hierbei noch eine deutlich effizientere Auftrennung als die Proben des aufgereinigten CoMoCAT-Materials. Dieses enth{\"a}lt zu jedem Zeitpunkt der Beschallung noch einen entsprechend gr{\"o}ßeren Anteil an aggregierten R{\"o}hren. Beim Schermischen funktionierte die Entb{\"u}ndelung von Black Sand im Vergleich zu CoMoCAT und HiPCO mit Abstand am besten, was sich auch in den ODVerh{\"a}ltnissen beschallter und gescherter Proben widerspiegelte. Die beobachtete Quantenausbeute war bei den durch Schermischen dispergierten DGUEinzelrohrproben um bis zu 50 \% h{\"o}her als bei den beschallten Proben, was auf eine deutlich niedrigere R{\"o}hrenbesch{\"a}digung und somit auch auf eine h{\"o}here R{\"o}hrenqualit{\"a}t hindeutete. Dies wurde auch durch Vergleichsmessungen an Einzelr{\"o}hren best{\"a}tigt. Außerdem dringt bei durch Ultraschall geschnittenen R{\"o}hren Wasser ins R{\"o}hreninnere ein, was beim Schermischen nicht der Fall ist. Das erm{\"o}glicht durch Schermischen vielleicht die Herstellung von Proben mit ver{\"a}nderten Eigenschaften. Beim Vergleich der Materialien zeigte HiPCO die h{\"o}chste Quantenausbeute. Dieses Herstellungsverfahren liefert also im Vergleich zum CoMoCAT-Verfahren eine bessere R{\"o}hrenqualit{\"a}t. Die um 70 \% h{\"o}heren Quantenausbeuten der Black Sand-Proben im Vergleich zu den CoMoCAT-Proben machten die R{\"o}hrenbesch{\"a}digungen bei der Aufreinigung des Rohmaterials deutlich. Werden zudem Besch{\"a}digungen durch Ultraschall ber{\"u}cksichtigt, betr{\"a}gt der Unterschied sogar 250 \%. Die beschallten HiPCO- und Black Sand-Proben der zeitabh{\"a}ngigen Messungen zeigten aufgrund der effizienten Entb{\"u}ndelung den schnellsten Anstieg der uantenausbeuten, welche aufgrund von Besch{\"a}digungen durch den Ultraschall, beeinflusst durch die Entb{\"u}ndelungsund Dispergierungseffizienzen der Materialien, nach 10-20 min wieder abfielen. Die Quantenausbeuten der gescherten Proben stiegen entsprechend langsamer {\"u}ber die gesamte Messzeit von sechs Stunden an. Die Dispergierung mittels Schermischer bei erh{\"o}hter Viskosit{\"a}t f{\"u}hrte bei einem Iodixanolanteil von 45 \% zu einer fast sechsfach h{\"o}heren Dispergierungseffizienz im Vergleich zu Wasser. Auch Lufteinschl{\"u}sse scheinen einen Einfluss zu haben, weshalb ein Probenvolumen zwischen 13-14 mL mit dem verwendeten Aufbau am sinnvollsten erscheint. Ob Viskosit{\"a}t und Lufteinschl{\"u}sse auch Entb{\"u}ndelungseffizienz und R{\"o}hrenqualit{\"a}t beeinflussen, muss noch untersucht werden. In Kapitel 5 wurde die Dispergierung von Nanor{\"o}hren mit kationischem Perylenbisimid untersucht. Nach dem Zusammengeben von PBI-L{\"o}sung und SDS-Nanorohrsuspension wurden Flokkulationseffekte beobachtet, welche durch hohe Nanorohr- oder SDS-Konzentrationen verz{\"o}gert wurden. Das erm{\"o}glichte die Herstellung von PBI-Nanorohrfilmen mit Streifenmuster durch Nutzung des Kaffeering-Effektes. Es wurde gezeigt, dass die Nanor{\"o}hren in das PBI eingebettet werden k{\"o}nnen. Allerdings waren die Streifen noch sehr unregelm{\"a}ßig und die R{\"o}hren in den Streifen nicht ausgerichtet. Die Stabilit{\"a}t der PBI-Nanorohrsuspensionen konnte durch einen Tensidaustausch vom anionischen SDS zum kationischen CTAB verbessert werden. Es konnte gezeigt werden, dass f{\"u}r die Vermeidung von Aggregationen w{\"a}hrend den daf{\"u}r n{\"o}tigen Dialysen unter anderem die m{\"o}glichst geringe Bewegung der Probe entscheidend ist. Außerdem musste die CTABKrafft-Temperatur von 25 °C ber{\"u}cksichtigt werden. Unterhalb dieser Temperatur bildet das Tensid keine Mizellen mehr, was die Suspensionen destabilisiert. Mischexperimente von CTAB-Nanorohrsuspensionen mit L{\"o}sungen aus verschiedenen CTAB:PBI-Verh{\"a}ltnissen lieferten Hinweise darauf, dass CTAB alleine die R{\"o}hren nicht stabilisiern kann. Ein Grund daf{\"u}r k{\"o}nnte eine zu geringe Anzahl an positiven Ladungen auf den R{\"o}hren sein. Demzufolge w{\"a}re immer ein gewisser Anteil an Tensid zur Stabilisierung notwendig. Trotz geringer Tensidbeimischung k{\"o}nnten aber Filme mit in PBI eingebetteten R{\"o}hren hergestellt werden. Unter Umst{\"a}nden k{\"o}nnten die R{\"o}hren auch in die fl{\"u}ssigkristalline Phase des PBIs eingebettet werden. Ein anderer Grund f{\"u}r die nicht ausreichende Stabilisierung k{\"o}nnte sein, dass die PBI-Aggregate nur sehr schlecht aufgetrennt werden. Dann k{\"o}nnte das PBI-Adsorptionsverhalten durch eine Verbesserung der Aggregatauftrennung beeinflusst werden. Zuletzt wurde in der vorliegenden Dissertation die Herstellung von Nanorohrgelfilmen beschrieben. Neben Homogenit{\"a}t durch Nutzung von Gelatine und Stabilit{\"a}t durch Entfernung von Iodixanol sorgte eine Silikonform f{\"u}r eine einheitliche Dicke und Gr{\"o}ße der pr{\"a}parierten (6,5)-Gelfilme. R{\"o}hrenaggregationen w{\"a}hrend der Iodixanolentfernung durch Zentrifugenfiltration konnten auf die Alterung der verwendeten Suspensionen zur{\"u}ckgef{\"u}hrt werden. Die optischen Dichten der so hergestellten Gelfilme standen immer in {\"a}hnlichen Verh{\"a}ltnissen zu denen der Ausgangssuspensionen, sodass die f{\"u}r die Gelfilme ben{\"o}tigten R{\"o}hrenkonzentrationen in den Ausgangssuspensionen relativ genau berechnet werden konnten. Um das Iodixanol f{\"u}r die Herstellung von (6,5)/(6,4)-Gelfilmen effektiv aus den Suspensionen zu entfernen, wurden drei verschiedene Dialysemembranen getestet. Dabei stellte sich die Membran mit einer Porengr{\"o}ße von 50 kD als bester Kompromiss aus effektiver Iodixanolentfernung und geringem R{\"o}hrenverlust heraus. Durch Einengung der (6,5)/(6,4)-Suspension konnten drei Gelfilme mit ausreichend hohen optischen Dichten hergestellt werden, wobei der dritte Film im Gegensatz zu den ersten beiden aufgrund des immer weiter abnehmenden Probenvolumens eine deutliche R{\"o}hrenaggregation zeigt. Dadurch eignen sie sich f{\"u}r weiterf{\"u}hrende Experimente, wo mit Hilfe der Transienten-Absorptionsspektroskopie Untersuchungen zu Energie- und Ladungstransferprozessen zwischen CNTs verschiedener Chiralit{\"a}ten durchgef{\"u}hrt werden k{\"o}nnten.}, subject = {Nanor{\"o}hre}, language = {de} } @phdthesis{Kanal2015, author = {Kanal, Florian}, title = {Femtosecond Transient Absorption Spectroscopy - Technical Improvements and Applications to Ultrafast Molecular Phenomena}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-118771}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Photoinduced processes are nowadays studied with a huge variety of spectroscopic methods. In the liquid phase, transient absorption spectroscopy is probably the most versatile pump-probe technique used to study light-induced molecular phenomena. Optical time-resolved spectroscopy is established in a large number of laboratories and is still further being developed with respect to many technical aspects. Nevertheless, the full potential of shortening the data-acquisition time—necessary for the investigation of rapidly photodegrading samples and observation of macroscopically fast processes—achievable with high-repetition-rate laser systems and shot-to-shot detection was not fully exploited. Especially, shot-to-shot detection is highly beneficial due to the high correlation of subsequent laser pulses. The development and implementation of 100 kHz broadband shot-to-shot data acquisition was presented in Chapter 3. For an established laser dye as a benchmark system, ultrafast excited-state dynamics were measured for the first time with broadband shot-to-shot detection at 100 kHz. An analysis of both the noise characteristics of the employed laser and the correlation of subsequent pulses quantified the advantage of shot-to-shot data acquisition. In the utilized software environment, the time for measuring a complete data set could be sped up by a factor of three or even higher compared to a laser system working at 1 kHz. So far, the limiting factor is the data processing and the movement of the mechanical delay stage. Nevertheless, the new shot-to-shot detection has the potential to shorten the measurement time up to a factor of 100. The data quality is improved by a factor of three when the hitherto conventional averaging scheme is compared to shot-to-shot acquisition for the same number of laser pulses. The expansion of shot-to-shot data acquisition for high repetition rates will allow studies on sensitive samples as exposure times can strongly be reduced to achieve the same signal-to-noise ratio. In addition, multidimensional spectroscopy can also be extended to high-repetition shot-to-shot readout allowing an efficient recording of data. Therefore, in future experiments, dynamics and couplings in sensitive samples and kinetic processes could be studied in more detail. Complex photophysical and photochemical phenomena are subject of many fields of research. Many of these multifaceted processes are not yet fully understood. Therefore, a possible approach is the elucidation of single reaction steps with the combination of transient absorption spectroscopy and a suitable, less complex model system. The systematic variation of the model system's properties and environments, e.g., by chemical substitution or adequate choice of the solvent allows the determination of essential entities and reactivities thereof. Proper knowledge of an individual intermediate step and its determining factors can enhance the understanding of the complete photoreaction process. The application of transient absorption spectroscopy was shown for the optically-induced electron transfer in a series of donor-acceptor oligomers in Chapter 4. In general, the solvent relaxation times were isolated from the back-electron-transfer dynamics by a global lifetime analysis. For the smallest oligomeric structure where complete charge separation is possible, an ultrafast equilibration leads to charge recombination from the configuration showing the lowest barrier for recombination. The back-electron transfer strongly depends on the utilized solvent. Whereas in dichloromethane the back-electron transfer occurs with the maximum rate in the barrierless optimal region, the dynamics in toluene are governed by a Marcus inverted-region effect. The experimentally observed rates were also estimated by theoretical calculations of the respective barriers. The study did not only successfully unravel charge transfer in the oligomeric systems but also improved the understanding of the electron-transfer properties of larger polymers from an earlier study. Therefore, the combination of length variation and time-resolved spectroscopy is an important step towards the correct prediction of charge-carrier dynamics in macroscopic devices, e.g., for photovoltaics. The bond dissociation of a carbon-monoxide-releasing molecule in aqueous solution was studied in Chapter 5 as a prototype reaction for the photo-triggered breaking of a bond. It was shown that upon excitation only one carbon-monoxide ligand of the tricarbonyl complex is dissociated. A fraction of the photolyzed molecules restore the intact initial complex by geminate recombination within the temporal resolution of the experiment. However, the recombination could be detected by the hot ground-state infrared absorption of the complex. The detectable dicarbonyl formed upon CO release distributes excess energy from the absorbed photon into low-frequency modes which result in broadened absorption bands like for the recombined tricarbonyl. The free coordination site in the ligand sphere is filled with a solvent water molecule. Despite numerous studies of metal carbonyls studied in alkaneous solutions, the elucidation of the dynamics of a CORM in aqueous solution added another important detail to the photochemistry of this class of compounds. Experiments employing a second ultraviolet pump pulse did not trigger further CO dissociation and hence no formation of a monocarbonyl species; this might either be due to a different release mechanism without a further photochemical step or a strong spectral shift of the dicarbonyl's absorption. Both reasons could explain why degenerate pump-repump-probe spectroscopy is inefficient. However, further experiments with ultraviolet probe pulses could substantiate whether the intermediate dicarbonyl reacts further photochemically or not. Apart from the model-system character of the CORM for bond dissociation, the study could determine exactly how many CO ligands are initially photolyzed off. Detailed knowledge of the release mechanism will affect the previous use and application as well as the further development of CORMs as therapeutic prodrugs to deliver high local concentrations of CO in cancerous or pathological tissue. Hence, the study of two-photon absorption properties which are important for in vivo applications of CORMs should be the main focus in further spectroscopic experiments. In Chapter 6, both abovementioned molecular phenomena—electron transfer and bond dissociation—were studied in combination. The photochemistry of a tetrazolium salt was studied in detail in a variety of different solvents. Being a relatively small molecule, the studied tetrazolium cation shows a multifaceted photochemistry and is therefore a textbook example for the combination of ultrafast molecular phenomena studied in different environments. Within femtoseconds, the tetrazolium ring is opened. The biradicalic species is then reduced via uptake of an electron from the solvent. The formation of the ring-open formazan photoproduct from this point of the reaction sequence on was excluded by experiments with acidic pH value of the solution. The ring-open radical is stabilized by ring-closure. The resulting tetrazolinyl radical was already observed in experiments with microsecond time resolution. However, its formation was observed in real time for the first time in this study. Irradiation of a tetrazoliumsalt solution yields different photoproduct distributions depending on the solvent. However, it was shown that all photoproducts have a tetrazolinyl radical as a common precursor on an ultrafast time scale. In combination with studies from the literature, the complete photochemical conversion of a tetrazolium salt was clarified in this study. Apart from the prototype character of the reaction sequence, the reaction mechanism will have impact on research associated with life science where tetrazolium assays are used on a daily basis without taking into account of photochemical conversion of the indicating tetrazolium ion and its photochemically formed reactive intermediates. On the basis of the tetrazolium-ion photochemistry, the rich photochemistry of the formazan photoproduct, including structural rearrangements and subsequent reformation of the tetrazolium ion, might be the subject of future studies. This thesis shows a method advancement and application of transient absorption spectroscopy to exemplary molecular model systems. The insights into each respective field did not only enlighten singular aspects, but have to be seen in a much larger context. Understanding complex photoinduced processes bottom-up by learning about their constituting steps—microscopically and on an ultrafast time scale—is an ideal method to approach understanding and prediction of phenomena in large molecular systems like biological or artificial architectures as for example used in photosynthetic light-harvesting and photovoltaics.}, subject = {Ultrakurzzeitspektroskopie}, language = {en} } @phdthesis{Gerbich2015, author = {Gerbich, Thiemo M. P.}, title = {Pikosekunden-zeitaufgel{\"o}ste Deaktivierungsprozesse in isolierten Molek{\"u}len - Fluorenon, NDCA, Me-NI und NTCDA}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-118654}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2015}, abstract = {Im Rahmen der vorliegenden Dissertation wurden die Dynamiken von strahlungslosen Deaktivierungsprozessen von vier verschiedenen Molek{\"u}len im elektronisch angeregten Zustand untersucht. Ein fundiertes Verst{\"a}ndnis der intramolekularen Energieumverteilung in isolierten pi-konjugierten Systemen ist neben dem Modellcharakter auch f{\"u}r Anwendungen in der organischen Elektronik von Interesse. Die Untersuchungen dienen zudem als optimaler Maßstab f{\"u}r theoretische Simulationen, die auf eine Nachbildung der molekularen Dynamik ausgerichtet sind. Die Inbetriebnahme des Pikosekunden-Lasersystems stellt in der Arbeitsgruppe ein großes Potential f{\"u}r die Untersuchung der Dynamik von isolierten pi-konjugierten Molek{\"u}len zur Verf{\"u}gung. Erste Experimente konnten an unterschiedlichen Heterocyclen mit interessantem zeitlichen Verhalten erfolgreich durchgef{\"u}hrt werden und lieferten bereits wichtige Erkenntnisse {\"u}ber die strahlungslose Deaktivierung auf der ps-Zeitskala. Selbst f{\"u}r große Molek{\"u}le mit geringem Dampfdruck, die nur mit hohem experimentellen Aufwand im isolierten Zustand charakterisierbar sind, konnten Relaxationszeiten der angeregten Zust{\"a}nde ermittelt werden. Der Fokus der einzelnen Studien lag in der Erforschung der isolierten Molek{\"u}le, welche durch Anwendung der Molekularstrahl-Technik mit zeitaufgel{\"o}ster REMPI-Spektroskopie anhand des ps-Systems untersucht werden sollten. Zur Kontrolle der experimentellen Ergebnisse wurden zudem Vergleichsmessungen der transienten Absorptionsspektroskopie (TA) in der Fl{\"u}ssigphase herangezogen, wodurch eine fundierte Interpretation der Dynamik m{\"o}glich wurde. Zu den wichtigen Zielen geh{\"o}rten jedoch die Vergleiche der experimentellen Ergebnisse von isolierten Molek{\"u}len mit Berechnungen der Zustandsenergien sowie Simulationen der Molek{\"u}ldynamik aus dem Theorie-Arbeitskreis von Prof. Mitric. Auf diese Weise konnten wichtige Erkenntnisse {\"u}ber die Dynamik der Deaktivierungsprozesse gewonnen werden. Die Kombination der Gasphasen-Experimente mit TA-Messungen in der Fl{\"u}ssigphase hat sich als besonders n{\"u}tzlich erwiesen, um bei mehrstufigen Deaktivierungsprozessen einen erweiterten Einblick in die Dynamik der Molek{\"u}le zu erhalten. - So konnte bei Fluorenon in Cyclohexan und Acetonitril durch Vergleich der Anregungen des S3- und S1-Zustands eine zus{\"a}tzliche Zeitkonstante von 8-16 ps beobachtet werden, welche die innere Umwandlung zum S1-Zustand dokumentiert und die Ergebnisse der Gasphasen-Messungen best{\"a}tigt. - Durch Verwendung von L{\"o}sungsmitteln unterschiedlicher Polarit{\"a}t und der damit verbundenen Verschiebung der elektronischen Zust{\"a}nde von Fluorenon konnte zudem der zweite Deaktivierungsprozess eindeutig einem ISC-Prozess mit Zeitkonstanten von 120-154 ps zugeordnet werden. In der Gasphase wurde dieser Prozess lediglich als langlebiger Offset wahrgenommen. - Unterschiedliche Anregungsenergien zeigten bei TA-Messungen von NDCA eine nahezu identische Molek{\"u}ldynamik mit ca. 200 ps, w{\"a}hrend f{\"u}r isoliertes NDCA ein starker Abfall der Lebensdauer mit zunehmender Schwingungsenergie beobachtet wurde. In der Gasphase wird somit von einer Deaktivierung {\"u}ber eine Energiebarriere ausgegangen, w{\"a}hrend in L{\"o}sung eine zu schnelle Abk{\"u}hlung durch Schwingungsrelaxation diesen Prozess verhindert. - Bei NTCDA konnten in den TA-Messungen nach Anregung des S1-Zustands eine Relaxation in die Triplett-Umgebung innerhalb von wenigen Pikosekunden beobachtet werden, was im Einklang mit der sehr schnellen Deaktivierung in der Gasphase betrachtet werden kann. Eine ausf{\"u}hrliche Vergleichsstudie von isolierten Molek{\"u}len mit computergest{\"u}tzten Rechnungen und Simulationen wurde f{\"u}r die Molek{\"u}le NDCA und Me-NI durchgef{\"u}hrt. Dabei wurde explizit auf den Einfluss von Spin-Bahn-Kopplungen und konischen Durchschneidungen eingegangen, welche zu konkurrierenden Deaktivierungsprozessen des S1-Zustands f{\"u}hren k{\"o}nnen. - Durch Simulationen der Surface-Hopping-Dynamik wurde deutlich, dass bei NDCA und Me-NI im ersten angeregten Zustand eine konische Durchschneidung (CI) zwischen dem S1- und S0-Zustand erreicht werden kann. - W{\"a}hrend die Dynamik von NDCA bei h{\"o}herer Schwingungsanregung stark durch die CI dominiert wird, spielt die direkte Relaxation in den elektronischen Grundzustand bei Me-NI offenbar keine Rolle. - In Abwesenheit der CI zeigen NDCA und Me-NI in einer mit Spin-Bahn-Kopplung erweiterten Simulation der Populationsdynamik einen signifikanten Populationstransfer in die Triplett-Umgebung (T1-T4). Eine innere Umwandlung in den Grundzustand konnte jedoch nur bei Erreichen der CI beobachtet werden. Eine weitere Verbesserung der ps-Experimente kann durch Aufbau eines Photoelektronen-Spektrometers erreicht werden, da durch diese Technik eine pr{\"a}zisere Aussage dar{\"u}ber getroffen werden kann, aus welchem elektronischen Zustand die Molek{\"u}le ionisiert wurden. Eine Unterscheidung von ISC- und IC-Prozessen k{\"o}nnte somit gew{\"a}hrleistet werden.}, subject = {REMPI}, language = {de} } @phdthesis{Voelker2014, author = {V{\"o}lker, Sebastian}, title = {Synthesis, Spectroscopic and Electrochemical Properties of Squaraine Polymers}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-101638}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {In this work the synthesis, the spectroscopic and electrochemical investigation as well as some applications of a broad diversity of indolenine squaraine dyes were presented. This diversity was based on two parent squaraine dyes, one standard trans-configured compound (M1) and one in which one central oxygen atom was replaced by a dicyanomethylene moiety (M2), which increased the acceptor strength and induced a cis-configuration. The variety of synthesised dyes included functionalised squaraine monomers, donor- and acceptor-substituted monomeric model squaraines, donor- and acceptor-squaraine copolymers, pure squaraine homopolymers, a squaraine-squaraine copolymer, as well as some conjugated cyclic oligomers. In order to be able to synthesise all these different kinds of dyes, several bromine and boronic ester derivatives were synthesised, which enabled the use of the Suzuki cross coupling reaction, to generate model dyes and copolymers. In addition, the bromine derivatives were used to carry out the Yamamoto homocoupling reaction to the respective homopolymers and macrocycles. The absorption maximum of unsubstituted reference dye M1 was found at ~ 15500 cm-1, while that of M2 was red-shifted to ~ 14300 cm-1 due to the increased acceptor strength of the central unit. The extinction coefficients were in the order of ~ 300000 M-1 cm-1 and ~ 200000 M-1 cm-1, respectively. It was found that the implementation of functional groups (M3-M9), additional electron donors (M10-M19) or acceptors (M20-M22) at the periphery lead to bathochromic shifts of the absorption depending on the strength of either - and/or -donating properties of the substituents. For the bis- and triarylamine substituted dyes M10-M13 and the dibrominated dyes M5 and M7 the electronic structure of the mono- and diradical (di)cations was explored using the interplay of cyclic voltammetry, spectroelectrochemistry, and DFT calculations. It was demonstrated that the monoradical cations still show a cyanine-like character and are delocalised Robin-Day class III species due to the low redox potential of the squaraine bridge between the additional amine redox centres. To the best of my knowledge, this made M13+∙, with an N-N-distance of 26 bonds between the additional redox centres to the longest bis(triarylamine) radical cation that is completely delocalised. For the diradical dications, the situation was of larger complexity. The computed most stable energetic state of the dianisylamine-substituted dyes turned out to be a broken-symmetry state with almost equal contributions of an open-shell singlet and triplet state. In addition, it was shown that the HOMO-1→HOMO transition dominated the absorption spectra of the diradical dications where the trans-/cis-configuration of the squaraines had a direct impact due to symmetry reasons. Based on the donor-squaraine model compounds M10-M19, a series of donor-squaraine copolymers was synthesised (P7-P12) in order to further red shift and broaden the low energy absorption band. However, these effects were only of marginal extent. Both the optical and the electrochemical derived band gaps were barely lowered compared to the respective monomeric model dyes. This was assigned to an increased squaraine-squaraine distance and resulting lower exciton coupling between the squaraine chromophores due to the bridging units. In addition, according to semiempirical calculations the bridges were twisted out of the squaraine plane what reduced conjugational effects between the chromophores. To sum up, the idea to insert additional electron rich bridging units in order to create copolymers with broad and red-shifted absorption did not fully work out for the presented systems. The addition of strong electron accepting NDI units at the periphery resulted in M21, the most unique monomeric model squaraine in this work. The common picture of a sharp low energy squaraine absorption completely altered due to the addition of the NDIs and a rather broad and solvent dependent low energy absorption was found. Spectroelectrochemical experiments and semiempirical calculations showed that this band is a superposition of the common squaraine HOMO→LUMO transition and a partial squaraine→NDI charge transfer transition. The latter was lost upon oxidation of the squaraine and the absorption spectrum of the monocation of M21 was found to be nearly a 1:1 image of a pure squaraine monocation. Both the monomeric model M21 and the respective copolymer P13 showed low electrochemically obtained band gaps of 1.05-1.20 eV, which were the lowest of all squaraines in this work. For both dyes, transient absorption measurements in the fs-time regime revealed the ultrafast formation of a CS state via an intermediate CT state within a few ps. Besides, charge recombination to the ground state also occured within a few ps. In the polymer, there was barely any further energy or charge transfer within the excited state lifetime and therefore the CS state was confined on adjacent squaraine-NDI pairs and did not further travel along the polymer strand. The Ni-mediated Yamamoto homocoupling reaction was applied for the synthesis of the homopolymers (P1-P5). In contrast to the donor-squaraine copolymers, those polymers revealed strongly red-shifted and broad absorption in the red to NIR region in addition to a sharp fluorescence. These features could be explained to originate mainly from the exciton coupling of localised excited states and the presence of different superstructures in solution. For the polymers P1 and P2, an elongated J-type polymer chain caused the strong lowest energy absorption band whereas a zig-zag type arrangement of the single chromophores lead to transitions into both low and high energy excited states of the excitonic manifold. For the polymers P3 and P4, several polymer fractions of different size were investigated. Here, also an elongated chain with J-type character induced the lowest energy absorption band whereas a helical H-type arrangement caused transitions to higher energies of the excitonic manifold. The fractions to which these structures were formed depended on the chain length and the solvent. In thin film measurements, it was shown that the initially in solution formed superstructures were partly retained in the thin film but could be altered by annealing procedures. A control of the superstructures should enable the controlled tuning of the optical properties. Despite the strong interaction of the chromophores in the excited state, the redox potentials of the homopolymers barely differed to those of the respective reference dyes, indicating negligible electronic interaction in the ground state. In addition squaraine-squaraine copolymer P6, consisting of alternating parent dyes M1 and M2, was synthesised. Likewise to the homopolymers, a broad and red-shifted absorption was observed. This was explained by exciton coupling theory, which was extended to also suit alternating copolymers. In toluene, an extraordinary narrow and intense lowest energy absorption band was observed. This exchange narrowing might be a result of a highly ordered J-type structure of the polymer especially in this solvent because it was not found in others. The features of the polymer may be compared to typical J-aggregates formed from monomeric cyanine molecules for example and the polymer used as model for excitonic interactions in an alternating copolymer. Transient absorption measurements revealed a strong energy dependence of the decay traces of the copolymer, most strikingly at early decay times. This was assigned to the occurrence of multiple excitations of one polymer strand (due to the large extinction coefficients of the polymer) and resulting exciton-exciton annihilation. Due to the large exciton diffusion constants that were estimated, the static exciton-exciton annihilation was the rate limiting process of the decay, in contrast to other conjugated polymers, where in thin film measurements the decay was diffusion controlled. To sum up, for the polymers consisting of exclusively squaraine chromophores, it was shown that the exciton coupling of single chromophores with strong transition dipole moments was a fruitful way to tune the absorption spectra. As a side product of some of the polycondensation reactions, unprecedented cyclic conjugated oligomers such as the triarylamine-bridged dimer Dim1, the cyclic homotrimers Tri1-Tri3, and the tetramer Tet1 were obtained by recycling GPC in low yields. Especially the cyclic trimers showed unusual absorption and even more extraordinary fluorescence properties. They showed multiple fluorescence bands in the NIR that covered a range from ~ 8000-12500 cm-1 (800-1250 nm). First hints from theoretical calculations indicated that the trimer was not fully planar but comprised a mixture of both planar and bent single squaraine chromophores. However, final results of the calculations were still missing at the time of writing. In the last part of this work, the application of some monomeric and polymeric squaraines in binary and ternary bulk heterojunction solar cells was demonstrated. Also the utilisation as a dopant in a polymer matrix in an OLED device was shown. The homopolymers P1-P4 were tested in the binary BHJ solar cells revealing poor performances and especially very low short circuit currents. The utilisation of the polymers P3 and P4 that carried the dicyanomethylene group resulted in higher open circuit voltages due to the lower LUMO energy levels but still an overall poor performance. Neither for the different alkyl chains nor for the size of the polymers was a trend observed. In the ternary BHJ solar cells, small amounts of either monomer M14 or polymers P1A, P4-1 or P13 were added to a P3HT/PCBM system in order to generate an additional pathway for charge or energy transfer that should result in a better device performance. However, for none of the tested squaraines, improved solar cells could be built. In similarity to the binary solar cells, the short circuit currents were lower compared to a P3HT/PCBM reference device. These low short circuit currents indicated that the morphology of the squaraine dyes was the major limitation in those devices. It is possible that the dimethyl groups at the indolenine hindered a favoured alignment of the compounds that would allow decent charge transport. In the squaraine doped OLED the squaraine M6 worked rather well as an NIR emitter. Already at low dye loads the fluorescence of the host polymer SY-PPV was completely quenchend and emission from the squaraine was observed. For electroluminescence measurements, a lower dye load (0.5 wt.\%) compared to the photoluminescence measurements was sufficient, indicating that apart from FRET additional quenching mechanisms were at work in the electrically driven devices such as charge carrier dynamics.}, subject = {Squaraine}, language = {en} } @phdthesis{Ruetzel2014, author = {R{\"u}tzel, Stefan}, title = {Pulse-Sequence Approaches for Multidimensional Electronic Spectroscopy of Ultrafast Photochemistry}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-98993}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2014}, abstract = {Observing chemical reactions in real time with femtosecond laser pulses has evolved into a very popular � field of research since it provides fascinating insights into the nature of photochemical transformations. Nevertheless, many photochemical reactions are still too complex for which reason the underlying mechanisms and all engaged species cannot be identi� fied thoroughly. In these cases, conventional time-resolved spectroscopy techniques reach their technical limits and advanced approaches are required to follow the conversion of reactants to their products including all reaction intermediates. The aim of this work was therefore the development of novel methods for ultrafast spectroscopy of photoreactive systems. Though the concept of coherent multidimensional spectroscopy has so far exclusively been used to explore photophysical phenomena, it also offers great potential for the study of photochemical processes due to its capability of extracting spectroscopic information along several frequency dimensions. This allows resolving the photochemical connectivity between various interconvertible molecular species with ultrafast temporal resolution on the basis of their absorption and emission properties as the spectral correlations are explicitly visualized in the detected spectra. The ring-open merocyanine form of the photochromic compound 6-nitro BIPS was studied in Chap. 4 of this work. Merocyanines and their associated ring-closed spiropyrans are promising candidates for future applications as, for instance, molecular electronics or optical data storage due to their unique property of being switchable between two stable con� gurations via light illumination. Transient absorption with sub-50 fs temporal resolution and broadband probing was employed to characterize the photodynamics of this system with variable excitation wavelengths. Using global data analysis, it could be inferred that two different merocyanine isomers with differing excited-state lifetimes exist in solution. These isomers differ in the cis/trans con� guration in the last bond of the methine bridge. The minority of isomers exist in the all-trans con� guration (TTT) while the isomer with a cis con� guration of the third dihedral angle (TTC) is dominant. A characteristic band, detected after long pump-probe delays, was attributed to the unidirectional cis->trans photoisomerization reaction of the TTC to the TTT form. The quantum yield of the reaction was estimated to be (18� +-4) \%. In addition, pronounced coherent vibrational wave-packet oscillations were observed and it was concluded that these signatures are related to the product formation. Coherent two-dimensional electronic spectroscopy was successfully implemented using a partially collinear pump-probe beam geometry in combination with a femtosecond pulse shaper. The use of a whitelight probe continuum enabled us to probe contributions far-off the diagonal over the complete visible range. By properly adjusting the relative phase between the � first two laser pulses with the pulse shaper, the principle of phase-cycling was explained and it was demonstrated that the measurement can be carried out in the so-called "rotating frame" in which the observed frequencies detected during the coherence time are shifted to lower values. It was shown that these concepts allow the extraction of the desired background-free photon echo while the amount of necessary data points is highly reduced. In order to put our proposal of multidimensional spectroscopy of photoreactive systems into practice, third-order two- and three-dimensional spectroscopy was then employed for an in-depth analysis of a photoreactive process, in which the photoisomerization of 6-nitro BIPS served as a model system. The measured two-dimensional spectra revealed the cis->trans photoisomerization after long population times. By collecting a large data set of two-dimensional spectra for short population times and by applying a Fourier transform along the population time axis, the third-order three-dimensional spectrum was obtained. The novelty of this approach compared to coherent two-dimensional spectroscopy is the introduction of a third axis associated with the vibrational frequencies of the molecular system. In this way, the formation of the reaction product was evidenced and it was shown that the product is formed in its fi� rst excited singlet state within 200 fs after excitation. This method hence visualizes the photochemical connections between different reactive molecular species in an intuitive manner and further exposes the normal modes connecting reactant and product. Such conclusions cannot be drawn with conventional third-order techniques such as transient absorption since they are not capable of capturing the full third-order response, but only a subset of it. The reaction mechanism and the role of the observed vibrational modes were uncovered by comparing the experimental data with the results of high-level quantum-chemical calculations performed by our collaborators in the group of Prof. B. Engels from the theoretical chemistry department at the University of W{\"u}rzburg. Specifi� c calculated molecular normal modes could be assigned to the experimentally observed vibrational frequencies and potential energy surfaces of the electronic ground state and of the � first excited state were computed. The technique implemented in this chapter is general and is applicable for the time-resolved analysis of a wide range of chemical reaction networks. In the fi� rst part of Chap. 5, coherent two-dimensional spectroscopy was employed to track the reaction paths of the related 6,8-dinitro BIPS after S1 excitation. Several differences to the photochemical properties of 6-nitro BIPS were found. From the 2D spectra, the cis-trans isomerization between the two merocyanine isomers could be excluded as a major reaction path for this compound. To explore the dynamics after reexcitation to higher-lying electronic states, pump-repump-probe spectroscopy was implemented and the formation of a new species, a radical cation, was observed. To identify the precursor isomer, triggered-exchange two-dimensional spectroscopy, a � fifth-order technique previously only available in the infrared regime for vibrational transitions, was implemented for the fi� rst time for electronic excitations in the visible. This approach combines the properties of the pump-repump-probe technique with the potential of coherent two-dimensional spectroscopy. It correlates the absorption frequency of a reactive molecular species with the emission signatures of the product formed from this species after an additional absorption of a photon. Using this method, it was unambiguously proven that only the TTC isomer reacts to the radical cation thus forming the precursor species of the reaction. Electronic triggered-exchange two-dimensional spectroscopy is hence another improved technology for time-resolved spectroscopy with applications in the study of multistep photoreactions and higher-lying electronic states. While in the two preceding chapters third- and � fifth-order experiments were discussed that neglect the vectorial character of light-matter interactions, Chap. 6 focused on a novel theoretical formalism enabling the description of light fi� elds optimized for polarization-sensitive higher-order nonlinearities. This formalism is based on the von Neumann time-frequency representation of shaped femtosecond laser pulses which permits the defi� nition of multipulse sequences on a discrete time-frequency lattice. Hence, not only the temporal spacing between subpulses is adjustable, but also the center frequencies may be adapted such that they � fit the experimental requirements. This method was generalized to the description of pulse sequences with time-varying polarization states. It was shown that by using this description, the polarization ellipticity, orientation angle, relative phase and intensity, and the time-frequency location of each subpulse is explicitly controllable. The accuracy of the transformations from Fourier space to von Neumann domain and vice versa was demonstrated. Moreover, a strict accordance between the von Neumann polarization parameters with the conventional parameters in time domain was found for well separated subpulses. A potential future application of this approach is polarization-sensitive multidimensional spectroscopy in which hidden cross peaks may be isolated by de� fining the pulses in the von Neumann picture with suitable polarization sequences. This method could also be used in quantum control experiments in which the polarization of the light fi� eld is used as a major control knob. This thesis summarizes our efforts to open the � field of femtochemistry to the concept of coherent multidimensional electronic spectroscopy. Making use of femtosecond pulse shaping, sub-50 fs temporal resolution, broadband spectral probing, higher-order nonlinearities, and new types of laser pulse descriptions, the presented methods might stimulate further future advancements in this research area.}, subject = {Ultrakurzzeitspektroskopie}, language = {en} } @phdthesis{Kunkel2022, author = {Kunkel, Pascal Gerhard}, title = {Nahinfrarot-Ultrakurzzeitspektroskopie an einwandigen Kohlenstoffnanor{\"o}hren in dotierten D{\"u}nnfilmen und Polymermatrizen}, doi = {10.25972/OPUS-26900}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-269004}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {Nanor{\"o}hren, die auf dem Element Kohlenstoff basieren, besitzen ein großes Potential f{\"u}r ihre Anwendung als neuartige und nachhaltige Materialien im Bereich der Optoelektronik und weiteren zukunftsweisenden Technologiefeldern. Um jedoch hierf{\"u}r genutzt werden zu k{\"o}nnen, ist ein tiefgreifendes Kenntnis {\"u}ber ihre außergew{\"o}hnlichen photophysikalischen Eigenschaften notwendig. Kohlenstoffnanor{\"o}hren sind als eindimensionale Halbleiter sehr vielseitige Materialien. Jedoch ist der Zusammenhang zwischen ihrer Eignung als Halbleiter und der daf{\"u}r notwendigen Dotierung nur sehr unzureichend verstanden. Die Ziele der vorliegenden Dissertation waren deshalb, ein grundlegendes Verst{\"a}ndnis der photophysikalischen Energietransferprozesse in Nanor{\"o}hren zu erlangen und den Einfluss von gezielten Dotierungen auf diese Prozesse im Hinblick auf ihre Eigenschaften als eindimensionale Halbleiter detailliert zu untersuchen. Die Grundlage f{\"u}r die Experimente bildeten verschiedene Filme aus einwandigen (6,5)-Kohlenstoffnanor{\"o}hren, die durch ein Polyfluoren-Copolymer in einer organischen L{\"o}sungsmittelumgebung isoliert wurden. Mit Hilfe der Ultrakurzzeitspektroskopie wurden die auf einer schnellen (ps-ns) Zeitskala ablaufenden photophysikalischen Prozesse an diesen Filmen unter verschiedenen Bedingungen untersucht und analysiert. In Kapitel 4 wurde der generelle Energietransfer der Kohlenstoffnanor{\"o}hren in Polymermatrizen im Detail studiert. Hierbei wurden durch Simulationen theoretische dreidimensionale Verteilungen von Kohlenstoffnanor{\"o}hren erzeugt und die nach einem Energietransfer vorliegenden Polarisationsanisotropien berechnet. Verschiedene Berechnungsans{\"a}tze ergaben, dass die Nanorohrdichte ϱSWCNT f{\"u}r ein Massen{\"u}berschuss X der Matrix nahezu unabh{\"a}ngig von dem R{\"o}hrenvolumen war und durch ϱSWCNT = X-1 · 40 000 μm-1 angen{\"a}hert werden konnte. Die Simulationen lieferten von der R{\"o}hrendichte abh{\"a}ngige Gaußverteilungen der zwischen den Nanor{\"o}hren vorliegenden Abst{\"a}nden. Aus den Verteilungen konnte weiterhin der Anteil an R{\"o}hren bestimmt werden, die f{\"u}r einen Energietransfer zur Verf{\"u}gung stehen. Weitere Simulationen von Nanorohrverteilungen lieferten die Polarisationsanisotropie in Abh{\"a}ngigkeit von der Anzahl an durchgef{\"u}hrten Energietransferschritten. Die Ergebnisse aus den Simulationen wurden zur Interpretation der Ultrakurzzeitmessungen angewandt. Hierbei wurden durch die Variation der Polymermatrix die zwischen den Nanor{\"o}hren vorliegenden Abst{\"a}nde ver{\"a}ndert und damit die Art und Intensit{\"a}t des Energietransfers kontrolliert. In Messungen der transienten Anisotropie zeigte sich, dass ein Exziton nach seiner Erzeugung zwei depolarisierende Energietransferschritte durchf{\"u}hrte. Die Zerfallsdynamiken des Exzitons gaben auch klare Hinweise auf weitere nicht depolarisierende Energietransferprozesse, die durch parallel zueinander stehende {\"U}bergangsdipolmomente erm{\"o}glicht wurden. Eine Erkl{\"a}rung f{\"u}r dieses Verhalten lieferte die faserige Struktur der Filme, die sich in Aufnahmen durch das Elektronenmikroskop zeigte. Das Kapitel 5 besch{\"a}ftigte sich mit dem Aufbau eines transienten Nahinfrarotspektrometers und den n{\"o}tigen experimentellen Umbauten zur Messung der transienten Absorption f{\"u}r energiearme Signale im Spektralbereich unterhalb von 1.4 eV. Hierzu wurde die Weißlichterzeugung f{\"u}r die Verwendung von Calciumfluorid umgebaut. Das erzeugte Weißlicht wurde in das aufgebaute Prismenspektrometer eingekoppelt, um es weitestgehend linear auf einer Energieskala zu dispergieren. Auf diese Weise wurden energiearme Spektralkomponenten nicht auf unverh{\"a}ltnism{\"a}ßig viele Pixel verteilt und konnten mit ausreichender Intensit{\"a}t detektiert werden. Die Lichtdetektion erfolgte mittels zweier Detektorzeilen aus Indiumgalliumarsenid, die das transiente Signal durch eine direkte Referenzierung stabilisierten. Weiterhin wurde in diesem Kapitel die Justage und die programmierte Ansteuerung des Systems detailliert beschrieben. Hierbei wurde auf die Justage der Einkopplung per Freistrahl, die Kalibrierung mittels Bandpassspektren sowie auf die Aufnahme von Weißlichtspektren und transienten Karten detailliert eingegangen. An Nanorohrdispersionen durchgef{\"u}hrten Testmessungen zeigten, dass das transiente Nahinfrarotspektrometer mit direkter Signalreferenzierung einwandfrei funktionierte und daher den beobachtbaren Spektralbereich auf den Bereich von Energien bis unterhalb von 1 eV erweiterte. Damit erm{\"o}glichte der Aufbau einen Zugang zu der Beobachtung gr{\"o}ßerer Nanorohrchiralit{\"a}ten sowie zu der Untersuchung von energiearmen, spektralen Signaturen von Nanorohrdefekten. In Kapitel 6 wurde das transiente Nahinfrarotspektrometer genutzt, um das zeitabh{\"a}ngige Verhalten von redoxchemisch p-dotierten Nanor{\"o}hren zu charakterisieren und quantitativ zu beschreiben. Hierzu wurden die spektralen Eigenschaften von SWCNT-D{\"u}nnfilmen als Funktion eines steigenden Dotierungsgrades durch die Messungen der transienten und linearen Absorption studiert. In der linearen Absorption im Bereich von 0.9 - 2.5 eV vereinfachte sich das Spektrum mit ansteigender Dotierung stark und verlor vor allem im Bereich des ersten Subbandes deutlich an Oszillatorst{\"a}rke. Bei starker Dotierung verschwanden die Signalbeitr{\"a}ge von X1 und der Phononenseitenbande. Weiterhin bleichte auch die bei mittleren Dotierungsgraden auftauchende Trionenabsorption aus und ging in die breite Absorptionsbande der H-Bande {\"u}ber. Das Erscheinen und Verschwinden der trionischen sowie exzitonischen Absorption war ebenfalls in der transienten Absorption durch zeitgleich auftretende/verschwindende Photobleichsignale zu erkennen. Sowohl der Zerfall des exzitonischen PB-Signals wie auch des Trions beschleunigte sich mit einer steigenden Dotierung. Die Zerfallszeit des Exzitons im undotierten Film betrug 6.87 ps und verk{\"u}rzte sich auf 0.732 ps bei h{\"o}heren Dotierungsgraden. Die Zerfallszeit des Photobleichens des Trions reduzierte sich von 2.02 ps auf 0.440 ps. Auffallend war hierbei, dass das Trion im Vergleich zu dem Exziton exponentiell zerfiel und damit auf eine Lokalisierung dieses Zustandes hinweist. Bei h{\"o}heren Dotierungsmittelkonzentrationen tauchte in der transienten Absorption ein neuer Signalbeitrag auf. Die Existenz dieses Signals konnte auf die H-Bande zur{\"u}ckgef{\"u}hrt werden und k{\"o}nnte auf einer Verschiebung des linearen Absorptionsspektrums aufgrund einer Renormalisierung der Bandl{\"u}cke oder der S{\"a}ttigung von Ladungstr{\"a}gern beruhen. Das Signal zeigte eine klare Abh{\"a}ngigkeit vom Dotierungsgrad des Nanorohrfilmes. So wies es eine hypsochrome Verschiebung auf, wurde spektral breiter und seine Zerfallsdauer reduzierte sich von 1.62 ps auf 0.520 ps mit steigendem Dotierungsgrad.}, subject = {Einwandige Kohlenstoff-Nanor{\"o}hre}, language = {de} } @phdthesis{Voelckel2022, author = {Voelckel, Markus}, title = {Zeitaufgel{\"o}ste Spektroskopie von nanoskaligen Halbleitern und Pyrenderivaten}, doi = {10.25972/OPUS-27611}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-276119}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {Um den jahrtausendealten Weg der Menschheit vom Papyrus {\"u}ber Buchdruck und siliziumbasierte Halbleiter in Richtung noch leistungsf{\"a}higerer Technologien zu gehen und weiterhin Heureka-Momente zu schaffen, bieten Kohlenstoffnanor{\"o}hren ein weites Forschungsfeld. Besonders die halbleitenden Charakteristika von SWNTs sowie die Manipulation dieser durch Dotierung bergen viele M{\"o}glichkeiten f{\"u}r zuk{\"u}nftige Anwendungen in moderner Elektrotechnologie. Der Weg zu einer industriellen Implementierung von SWNTs in neuartigen optoelektronischen Bauteilen ließe sich durch eine Ausweitung des Wissens bez{\"u}glich SWNTs und der dotierungsbasierten Anpassung ihrer Eigenschaften ebnen. Mit dieser Erkenntniserweiterung als Zielsetzung wurden im Rahmen dieser Dissertation halbleitende, einwandige (6,5)-Kohlenstoffnanor{\"o}hren als chiralit{\"a}tsreine, polymerstabilisierte Proben untersucht. Die ultrakurzzeitaufgel{\"o}ste Spektroskopie der SWNTs erfolgte an organischen Suspensionen wie auch D{\"u}nnschichtfilmen, die je mittels eines gewissen Quantums an Gold(III)-chlorid dotiert worden waren. So konnten die ablaufenden Dynamiken auf einer ps-Zeitskala untersucht werden. In Kapitel 4 konnte mittels transienter Absorptionsexperimente an redoxchemisch p-dotierter SWNT-Suspensionen zun{\"a}chst gezeigt werden, dass sich die bei optischer Anregung gebildeten Trionen nicht analog zu Exzitonen diffusiv entlang der Nanor{\"o}hre bewegen, sondern lokalisiert vorliegen. Die l{\"a}ngere trionischen Zerfallsdauer nach X\$_1\$- verglichen mit X\$_1^+\$-resonanter Anregung zeugt außerdem davon, dass das Trion aus dem Exziton gespeist wird. Der Einfluss der Dotierung auf die Zerfallsdynamiken von X\$_1\$ und X\$_1^+\$ wurde an SWNT-D{\"u}nnschichtfilmen untersucht. Das Photobleichsignal des Exzitons verschiebt hypsochrom und zerf{\"a}llt schneller mit zunehmender Ladungstr{\"a}gerdichte durch h{\"o}herer Gold(III)-chloridkonzentrationen. Dies resultiert aus dem verringerten Abstand zwischen den Ladungstr{\"a}gern, welche als nichtstrahlende L{\"o}schstellen fungieren. F{\"u}r das X\$_1^+\$-PB ist ein {\"a}hnliches Verhalten zu beobachten. Dabei wird dieses Signal mit weiter steigender Dotierung von einer der H-Bande zuzuordnenden Photoabsorption {\"u}berlagert. Diese l{\"a}sst sich in einer starken S{\"a}ttigung der Dotierung wie auch einer hohen Bandkantenverschiebung begr{\"u}nden. In Kapitel 5 wurde die Gr{\"o}ße der Exzitonen und Trionen in dotierten SWNT-D{\"u}nnschichtfilmen mittels des Phasenraumf{\"u}llmodells bestimmt. Dabei lag besonderes Augenmerk auf der Kompensation des PB/PA-{\"U}berlapps, dem schnellen Zerfall, einem Ausgleich von Differenzen zwischen Anrege- und Absorptionsspektrum sowie dem Anteil intrinsischer/dotierter Nanorohrsegmente, um korrigierte Gr{\"o}ßen \$\xi_\mathrm{k}\$ zu erhalten. F{\"u}r die Trionengr{\"o}ße wurde zus{\"a}tzlich der {\"U}berlapp der Absorptionsbanden einbezogen, um korrigierte Werte \$\xi_{\mathrm{T,k}}\$ zu bestimmen. \$\xi_\mathrm{k}\$ betr{\"a}gt in der intrinsischen Form 6\$\pm\$2\,nm und bleibt bis zu einer Ladungstr{\"a}gerdichte \$n_{\mathrm{LT}}<0.10\$\,nm\$^{-1}\$ etwa gleich, anschließend ist ein Absinken bis auf etwa 4\,nm bei \$n_{\mathrm{LT}}\approx0.20\$\,nm\$^{-1}\$ zu beobachten. F{\"u}r diesen Trend ist die {\"U}berlagerung von Exziton- und H-Bande verantwortlich, da so der Faktor zur Bestimmung des Anteils intrinsischer Nanorohrsegmente an der SWNT verf{\"a}lscht wird. Die Abweichung der intrinsischen Gr{\"o}ße von den in der Literatur berichteten 13\$\pm\$3\,nm ist m{\"o}glicherweise auf Unterschiede in der Probenpr{\"a}paration zur{\"u}ckzuf{\"u}hren. F{\"u}r die Trionengr{\"o}ße ergibt sich bei steigender Dotierung ein {\"a}hnliches Verhalten: Sie betr{\"a}gt f{\"u}r \$n_{\mathrm{LT}}<0.20\$\,nm\$^{-1}\$ 1.83\$\pm\$0.47\,nm, was in der Gr{\"o}ßenordnung in guter {\"U}bereinstimmung mit der Literatur ist. F{\"u}r h{\"o}here Dotierungen sinkt \$\xi_{\mathrm{T,k}}\$ bis auf 0.92\$\pm\$0.26nm ab. Dies erkl{\"a}rt sich dadurch, dass bei h{\"o}herer \$n_{\mathrm{LT}}\$ die H-Bande das Spektrum dominiert, sodass der Einfluss der Absorptionsbanden{\"u}berlagerung nicht mehr vollst{\"a}ndig durch den entsprechenden Korrekturfaktor kompensiert werden kann. Kapitel 6 besch{\"a}ftigte sich anstelle redoxchemischer Dotierung der nanoskaligen Halbleiter mit der (spektro-)elektrochemischen Untersuchung von Vorl{\"a}ufern molekularer Radikale. SWV-Messungen weisen dabei darauf hin, dass die Pyrene Pyr1-Pyr3 entsprechend der Anzahl ihrer Substituenten bei Reduktion Mono-, Bi- beziehungsweise Tetraradikale bilden. Die strukturelle {\"A}hnlichkeit der Molek{\"u}le {\"a}ußert sich in gleichen Reduktionspotentialen wie auch {\"a}hnlichen potentialabh{\"a}ngigen Absorptionsspektren. W{\"a}hrend nur marginale Unterschiede in den PL-Spektren der neutralen und reduzierten Spezies festgestellt werden konnte, lieferte das zeitkorrelierte Einzelphotonenz{\"a}hlen aufschlussreichere Ergebnisse: So wird die Fluoreszenzlebensdauer stark von der Polarit{\"a}t der Umgegbung beeinflusst - bereits die Zugabe des Leitsalzes f{\"u}hrt hier zu {\"A}nderungen. Die durchschnittliche Fluoreszenzlebensdauer \$\tau_{\mathrm{av}}\$ sinkt außerdem mit Reduktion und Radikalbildung; f{\"u}r h{\"o}here Emissionswellenl{\"a}ngen ist \$\tau_{\mathrm{av}}\$ außerdem h{\"o}her. Insgesamt verdeutlichten die Experimente die gute Abschirmung zwischen Pyrenkern und Naphthalimidsubstituenten der Molek{\"u}le sowie die Sensibilit{\"a}t gegen{\"u}ber dem Medium durch TICT, das Vorhandensein von Bi- und Tetraradikalen kann allerdings nicht vollst{\"a}ndig belegt werden, wof{\"u}r EPR-Messugen notwendig w{\"a}ren.}, subject = {Dotierung}, language = {de} } @phdthesis{Riese2019, author = {Riese, Stefan}, title = {Photophysics and Spin Chemistry of Donor-Acceptor substituted Dipyrrinato-Metal-Complexes}, doi = {10.25972/OPUS-18022}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-180228}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2019}, abstract = {In this thesis, the photophysics and spin chemistry of donor-photosensitizer-acceptor triads were investigated. While all investigated triads comprised a TAA as an electron donor and a NDI as an electron acceptor, the central photosensitizers (PS) were different chromophores based on the dipyrrin-motif. The purity and identity of all target compounds could be confirmed by NMR spectroscopy, mass spectrometry and elemental analysis. The first part of the work dealt with dipyrrinato-complexes of cyclometalated heavy transition metals. The successful synthesis of novel triads based on Ir(III), Pt(II) and Pd(II) was presented. The optical and electrochemical properties indicated charge separation (CS), which was confirmed by transient absorption (TA) spectroscopy. TA-spectroscopy also revealed that the process of CS is significantly slower and less efficient for the triads based on Pt(II) and Pd(II) than for the analogous Ir(III) triads. This is mostly due to a much more convoluted reaction pathway, comprising several intermediate states before the formation of the final charge separated state (CSS2). On the other hand, CSS2 exhibits long lifetimes which are dependent on the central metal ion. While the Ir(III) triads show lifetimes of about 0.5 µs in MeCN, the Pt(II) and Pd(II) analogues show lifetimes of 1.5 µs. The magnetic field effect on the charge recombination (CR) kinetics of CSS2 was investigated by magnetic field dependent ns-TA spectroscopy and could be rationalized based on a classical kinetic scheme comprising only one magnetic field dependent rate constant k±. The behavior of k± shows a clear separation of the coherent and incoherent spin interconversion mechanisms. While the coherent spin evolution is due to the isotropic hyperfine coupling with the magnetic nuclei of the radical centers, the incoherent spin relaxation is due to a rotational modulation of the anisotropic hyperfine coupling tensor and is strongly dependent on the viscosity of the solvent. This dependence could be used to measure the nanoviscosity of the oligomeric solvent pTHF, which was found to be distinctly different from its macroviscosity. The second part of the work dealt with bisdipyrrinato complexes and their bridged porphodimethenato (PDM) analogues. Initially, the suitability of the different chromophores for the use as PS in donor-acceptor substituted triads was tested by a systematic investigation of their steady state and transient properties. While the PDM-complex of Zn(II) and Pd(II) exhibited promising characteristics such as a high exited state lifetime and relatively intense emission, the purely organic parent PDM and the non-bridged bisdipyrrinato-Pd(II) complex were less suitable. The difference between the two Pd(II) complexes could be explained by a structural rearrangement of the non-bridged complex which results in a non-emissive metal centered triplet state with disphenoidal geometry. This rearrangement is prevented by the dimethylmethylene-bridges in the bridged analogue resulting in higher phosphorescence quantum yields and excited state lifetimes. With the exception of the Zn(II)PDM-complex, the synthesis of novel donor acceptor substituted triads could be realized for all desired central chromophores. They were investigated equivalently to the cyclometalated triads described in the first part. The steady state properties indicate a stronger electronic coupling between the subunits due to the lack of unsaturated bridges between the donor and the central chromophore. Photoinduced CS occurs in all investigated triads. Due to the low exited state lifetimes of the central chromophores, CSS is formed less efficiently for the triads based on the unbridged Pd(II)-complex as well as the purely organic PDM. In the triad based on the bridged Pd(II) complex, the CR of CSS2 is faster than its formation resulting in low intermediate concentrations. For its elongated analogue, this is not the case and CSS2 can be observed clearly. Although the spin-chemistry of the triads based on bisdipyrrinato-Pd(II) and porphodimethenato-Pd(II) is less well understood, first interpretations of the magnetic field dependent decay kinetics gave results approximately equivalent to those obtained for the cyclometalated triads. Furthermore, the MFE was shown to be useful for the investigation of the quantum yield of CS and the identity of the observed CSSs. In both parts of this work, the influence of the central photosensitizer on the photophysics and the spin chemistry of the triads could be shown. While the process of CS is directly dependent on the PS, the PS usually is not directly involved in the final CSSs. None the less, it can still indirectly affect the CR and spin chemistry of the CSS since it influences the electronic coupling between donor and acceptor, as well as the geometry of the triads.}, subject = {Charge-transfer-Komplexe}, language = {en} } @phdthesis{Niklaus2022, author = {Niklaus, Lukas}, title = {Electrochromic systems based on metallopolymers and metal oxides: towards neutral tint and near-infrared transmission modulation}, doi = {10.25972/OPUS-25855}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-258554}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {While the field of electrochromic (EC) materials and devices (ECDs) continues to advance in terms of color palette and understanding the underlying mechanism, several scientific and technological challenges need to be addressed by optimizing the materials and understanding the electrochemical interplay of these materials in full cells. The main issue here is to further improve the EC profile for color neutrality and cycling stability in order to commercialize dimmable EC products. The transparent conductive substrates used in this work (FTO and ultra-thin ITO glass) have high visible light transmittance (τv > 85\%) and low sheet resistance (< 25 Ω·sq-1). In addition, the Li+-containing gel electrolyte has sufficient ionic conductivity (2.8·10-4 S·cm-1 at 25 °C), so the investigated ECDs could achieve a fast response (required ionic conductivity is between 10-3 and 10-7 S·cm-1). This work shows that the combination of cathodically-coloring Fe-MEPE with anodically-coloring non-stoichiometric nickel oxide (Ni1-xO) electrodes (prepared by the National Institute of Chemistry in Ljubljana, Slovenia) can be used in neutral-coloring type III ECDs. The Fe-MEPE/Ni1-xO ECD with the underbalanced CE (ECD1-1, 2: 1) and the balanced configuration (ECD1-2, 1: 1) are both nearly neutrally-colored (ECD1-1: a* = -6.7, b* = 8.8; ECD1-2: a* = -9.0, b* = 10.1) in the bright state with a τv of almost 70\%. Due to the overbalancing of the CE (ECD1-3, 1:3), a deviation (a* = -2.8, b* = 19.9) from the neutral coloration occurred here. The balanced as well as the overbalanced ECD configurations show high electrochemical cycling stability (over 1,000 potentiostatic switching cycles). In general, the overbalanced configuration offers the advantage of a smaller operating voltage range (-1 V ↔ 2.5 V to -1 V ↔ 1.5 V), i.e., avoiding possible electrochemical degradation of the EC materials, electrolyte, or conductive layers. By using a Li RE in the full cell, insights into the optimal matching of electrochemical and optical properties between the two electrodes are obtained to achieve more stable ECDs. Thereby, the redox potentials of both EC electrodes (Fe-MEPE and Ni1-xO) can be measured during operation. The incomplete decolorization of ECD1-1 can be explained by the measured electrode potentials (below the required 4 V vs. Li/Li+), excluding side reactions and degradation at both electrodes. The results demonstrate the importance of using balanced and (slightly) overbalanced ECD configurations with complementary-coloring EC electrodes to achieve high cycling stability and fast switching at low operating voltages. Therefore, this three-electrode configuration provides an excellent method for in situ electrochemical characterization of the individual EC electrodes to better understand the redox processes during device operation and to further improve the optical contrast and cycle stability of ECDs. The Fe-MEPE/Ni1-xO combination was tested on flexible ultrathin ITO glass (ECD1-4). Here, by applying a low voltage of -1 V ↔ 2.5 V, the MEPE/Ni1-xO ECDs can be reversibly switched from a colored (L* = 35.6, a* = 19.4, b* = -26.7) to a nearly colorless (L* = 78.5, a* = -14.0, b* = 21.3) state. This is accompanied by a change in τv from 6\% to 53\%. The ECDs exhibit fast response and good cycling stability (5\% loss of optical contrast over 100 switching cycles). To further improve color neutrality and cycling stability, ECDs combining Fe-MEPE and mixed metal oxides as ion storage layers were investigated. Titanium manganese oxide (TMO, Fraunhofer IST) and titanium vanadium oxide (TiVOx, EControl-Glas GmbH \& Co. KG) electrodes are compared for use as optically-passive ion storage layers. TiVOx with a maximum charge density of approx. 27 mC·cm-2 and a coloration efficiency of η = 2 cm·C-1 at 584 nm shows a color change from yellow to light gray at 2 V vs. Ag/AgCl, while the slightly anodically-coloring Ti-rich TMO (10.5 mC·cm-², η584 nm = -4 cm·C-1) switches from light yellow to colorless at -2.5 V vs. Ag/AgCl. These materials show only a slight change in τv value from 85\% to 75\% and from 72\% to 81\%, respectively, thus reaching the requirements for highly transmissive optical-passive ion storage layers. The ECDs with Fe-MEPE in combination with TiVOx (ECD2-1) and TMO-1 (ECD2-2) are blue-purple in the dark state (0 V) and turn colorless by applying a voltage of 1.5 V, changing the τv value from 28\% to 69\% and from 21\% to 57\% in 3 s and 13 s, respectively. The ECDs show fast responses and high cyclability over more than 100 cycles. In the last section, the simplification of cell architecture by using redox mediators shows that different redox mediators (KHCF(III), Fc-PF6, Fc-BF4, and TMTU) can be used in type II ECDs (4 instead of 5 layers) consisting of Fe-MEPE or Ni1-xO thin film electrodes. The combination of KHCF(III) with Fe-MEPE has a low cycling stability due to the electrochemical formation of Prussian blue (PB). This side reaction is undesirable as it decreases the optical contrast. It can be avoided by using Fc+- (ECD3-5/6) or TMTU-based (ECD3-7) redox mediators, which exhibit reversible redox behavior. A high τv value of 72\% is obtained for the use of TMTU. Low concentrations (<0.1 M) of redox mediators decrease the cell voltage for complete switching without affecting the optical properties of the ECDs. The redox couple TMTU/TMFDS2+ (molar ratio of 1:0.1 in 1 M LiClO4/PC as electrolyte) works well in combination with Ni1-xO electrodes (ECD3-10), with a change in τv value from 38\% (colored at 2 V, L* = 67.1, a* = 3.9, b* = 17.2) to 70\% at (decolored at -2 V, L* = 86.6, a* = -0.6, b* = 17.2). This result implies that incorporating redox mediators into the electrolyte is an effective means to simplify the cell assembly and color neutrality can be obtained with one optically active WE and a color-neutral redox mediator. Moreover, the combination of Ni1-xO and the colorless TMTU/TMFDS2+ redox mediator is a potential candidate to obtain neutrally colored ECDs. It is shown that the lab-sized FTO- and ultra-thin ITO-glass-based ECDs are very attractive for energy-efficient EC applications, e.g., in architectural or automotive glazing, aircraft, ships, home appliances and displays. To monitor the EC performance and to prevent diverging electrode potentials during the switching process, the studied three-electrode configuration can help to extend the cycle stability as well as to improve the charge balancing of dimmable applications. The studied ECDs display a route towards neutral tint, e.g., EC active Ni1-xO, optically-inactive mixed metal oxides, and colorless redox mediators. Nevertheless, color neutrality should be further improved to meet the requirements for industrial applications. For future work, a scale-up process from lab-sized (few cm²) to prototype (few m²) ECDs will be necessary.}, subject = {Elektrochromie}, language = {en} } @phdthesis{Hoche2023, author = {Hoche, Joscha}, title = {The life of an exciton: From ultrafast nonradiative relaxation to high quantum yield fluorescence}, doi = {10.25972/OPUS-31684}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-316844}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2023}, abstract = {This thesis focuses on understanding and predicting processes in chromophores after electronic state excitation, particularly the impact on luminescence - the spontaneous emission of light. It considers the effect of processes preceding luminescence on emission properties, which are challenging to predict, especially in complex aggregates. For example, excitation energy transfer is a crucial process in understanding luminescence, as it allows the emission to occur from different molecular units than where the absorption occurs. This can lead to significant shifts in emission wavelength and fluorescence quantum yields. The thesis offers solutions to model this process effectively, understanding the impact of excitation energy and exciton coupling disorder on energy transfer rates and linking simulated energy transfer to experimental measurements. The work further explores excimer formation - an undesired luminescence loss channel due to its significant stabilization of the electronic state. Usually, the molecules obey a stacked conformation with parallel orientation to maximize the orbital overlap. This energetic lowering of the excited state can often result in trapping of the dimer in this state due to a deep minimum on the potential energy surface. The excimer formation dynamics, structural rearrangement, and its influence on singlet-correlated triplet pair states formation, critical for the singlet-fission process, have been extensively studied. The thesis also focuses on another luminescence loss channel triggered by conical intersections between the electronic ground and the first excited states. A new model is introduced to overcome limitations in current simulation methods, considering the solvent's electrostatic and frictional effects on the barriers. The model accurately describes merocyanine dyes' solvent-dependent photoluminescence quantum yields and characterizes all relaxation channels in different BODIPY oligomer series.}, subject = {Theoretische Chemie}, language = {en} } @phdthesis{Oberndorfer2022, author = {Oberndorfer, Florian}, title = {Photoluminescence and Raman spectroscopy of doped nanomaterials}, doi = {10.25972/OPUS-27854}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-278540}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {This thesis includes measurements that were recorded by cooperation partners. The EPR spec- trosa mentioned in section 5.2 were recorded by Michael Auth from the Dyakonov Group (Ex- perimental Physics VI, Julius-Maximilians-Universit{\"a}t, W{\"u}rzburg). The TREFISH experiments and transient absorption in section 5.4 spectra were performed by Jašinskas et al. from the V. Gulbi- nas group (Center for Physical Sciences and Technology, Vilnius, Lithuania). This dissertation investigated the interactions of semiconducting single-walled carbon nanotubes (SWNTs) of (6,5) chirality with their environment. Shear-mixing provided high-quality SWNT sus- pensions, which was complemented by various film preparation techniques. These techniques were in turn used to prepare heterostructures with MoS2 and hBN, which were examined with a newly constructed photoluminescence microscope specifically for this purpose. Finally, the change of spectral properties of SWNTs upon doping was investigated in more detail, as well as the behaviour of charge carriers in the tubes themselves. To optimise the SWNT sample preparation techniques that supplied the other experiments, the sample quality of shear-mixed preparations was compared with that of sonicated samples. It was found that the quantum efficiency of sheared suspensions exceeds that of sonicated suspensions as soon as the sonication time exceeds 30 min. The higher PLQY is due to the lower defect concentration in shear-mixed samples. Via transient absorption, a mean lifetime of 17.3 ps and a mean distance between defects of 192.1 nm could be determined. Furthermore, it was found that the increased efficiency of horn sonication is probably not only due to higher shear forces acting on the SWNT bundles but also that the shortening of PFO-BPy strands plays a significant role. Sonication of very long polymer strands significantly increased their effectiveness in shear mixing. While previous approaches could only achieve very low concentrations of SWNTs in suspensions, pre-sonicated polymer yielded results which were comparable with much shorter PFO-BPy batches. Reference experiments also showed that different aggregation processes are relevant during production and further processing. Initial reprocessing of carbon nanotube raw material requires 7 h sonication time and over 24 h shear mixing before no increase in carbon nano concentration is detectable. However, only a few minutes of sonication or shear mixing are required when reprocessing the residue produced during the separation of the slurry. This discrepancy indicates that different aggregates are present, with markedly different aggregation properties. To study low-dimensional heterostructures, a PL microscope was set up with the ability to ob- serve single SWNTs as well as monolayers of other low-dimensional systems. Furthermore, sam- ples were prepared which bring single SWNTs into contact with 2D materials such as h-BN andMoS2 layers and the changes in the photoluminescence spectrum were documented. For h-BN, it was observed whether previous methods for depositing SWNTs could be transferred for photo- luminescence spectroscopy. SWNTs were successfully deposited on monolayers via a modified drip coating, with the limitation that SWNTs aggregate more at the edges of the monolayers. Upon contact of SWNTs with MoS2, significant changes in the emission properties of the mono- layers were observed. The fluorescence, which was mainly dominated by excitons, was shifted towards trion emission. Reference experiments excluded PFO-BPy and toluene as potential causes. Based on the change in the emission behaviour of MoS2, the most plausible explanation is a photoinduced charge transfer leading to delocalised charge carriers on MoS2. In contrast, on SWNTs, the introduction of additional charges would constitute a quenching centre, which would quench their PL emission, making them undetectable in the PL image. In the last chapter, the electronic properties of doped SWNTs and the behaviour of charge carri- ers inside the tubes should be investigated. First, the change in the conductivity of SWNT films with increasing doping levels was docu- mented. The resistance of the films drops drastically at minimum doping. After the initial in- troduction of charges, the resistance drops with increasing dopant concentration according to a double logarithmic curve. The initial drop could be due to a reduction of contact resistances within the SWNT network film, but this could not be further investigated within the scope of this PhD thesis. In cooperation with Andreas Sperlich and Michael Auth, the spin concentration of SWNTs at different doping levels was determined. The obtained concentrations were compared with the carrier concentrations determined from PL and absorption spectra. At low spin densities, good agreement with previous models was found. Furthermore, the presence of isolated spins strongly suggests a localised charge carrier distribution at temperatures around 10 K. When the charge density is increased, the spin density deviates significantly from the charge carrier con- centration. This discrepancy is attributed to the increasing delocalisation of charge carriers at high charge densities and the interactions of neighbouring spins. These results strongly indicate the existence of localised charge carriers in SWNTs at low temperatures. Next, the effect of doping on the Raman spectra of SWNT suspensions was investigated. In gen- eral, doping is expected to reduce the intensity of the Raman bands, i.e. a consequence of the reduced resonance gain due to bleaching of the S2 transition. However, similar to the resistivity measurements, the oscillator strength of the G+ band drops sharply in the first doping steps. It was also found that the G+ band decreases more than would be expected due to loss of reso- nance condition. Furthermore, the G- is bleached faster than the G+ band. All these anomalies suggest that resonance enhancement is not the only relevant effect. Another much faster deac- tivation path for the excitons may be introduced by doping. This would leave less time for the scattering process to occur and reduce the oscillator strength of the Raman bands. In cooperation with Vidmantas et al., the photoinduced charge carrier behaviour of SWNT/PCBM films was investigated. The required films were prepared by drop coating. The SWNT suspen- sions required for this were obtained from sheared SWNT preparations. Using transient absorp- tion and TREFISH, a number of charge transfer effects were identified and their dynamics in- vestigated: the recombination of neutral excitons (< 50 ps), the electron transfer from carbon nanotubes to PCBM molecules (< 1 ps), the decay of charge-transfer excitons (∼200 ps), the recombination of charge carriers between charge-transfer excitons (1 ns to 4 ns) and finally the propagation through the SWNT network (∼20 ns)}, subject = {Einwandige Kohlenstoff-Nanor{\"o}hre}, language = {en} } @article{SoaviScotognellaViolaetal.2015, author = {Soavi, Giancarlo and Scotognella, Francesco and Viola, Daniele and Hefner, Timo and Hertel, Tobias and Cerullo, Giulio and Lanzani, Guglielmo}, title = {High energetic excitons in carbon nanotubes directly probe charge-carriers}, series = {Scientific Reports}, volume = {5}, journal = {Scientific Reports}, number = {9681}, doi = {10.1038/srep09681}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-143061}, year = {2015}, abstract = {Theory predicts peculiar features for excited-state dynamics in one dimension (1D) that are difficult to be observed experimentally. Single-walled carbon nanotubes (SWNTs) are an excellent approximation to 1D quantum confinement, due to their very high aspect ratio and low density of defects. Here we use ultrafast optical spectroscopy to probe photogenerated charge-carriers in (6,5) semiconducting SWNTs. We identify the transient energy shift of the highly polarizable S\(_{33}\) transition as a sensitive fingerprint of charge-carriers in SWNTs. By measuring the coherent phonon amplitude profile we obtain a precise estimate of the Stark-shift and discuss the binding energy of the S\(_{33}\) excitonic transition. From this, we infer that charge-carriers are formed instantaneously (<50 fs) even upon pumping the first exciton, S\(_{11}\). The decay of the photogenerated charge-carrier population is well described by a model for geminate recombination in 1D.}, language = {en} } @phdthesis{Bach2017, author = {Bach, Tobias}, title = {Electromechanical interactions in lithium-ion batteries: Aging effects and analytical use}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-153325}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2017}, abstract = {In the first part of his work, the causes for the sudden degradation of useable capacity of lithium-ion cells have been studied by means of complementary methods such as computed tomography, Post-Mortem studies and electrochemical analyses. The results obtained point unanimously to heterogeneous aging as a key-factor for the sudden degradation of cell capacity, which in turn is triggered by differences in local compression. At high states of health, the capacity fade rate is moderate but some areas of the graphite electrode degrade faster than others. Still, the localized changes are hardly noticeable on cell level due to averaging effects. Lithium plating occurs first in unevenly compressed areas, creating patterns visible to the human eye. As lithium plating leads to rapid consumption of active lithium, a sudden drop in capacity is observed on cell level. Lithium plating appears to spread out from the initial areas over the whole graphite electrode, quickly consuming the remaining useful lithium and active graphite. It can be hypothesized that a self-amplifying circle of reciprocal acceleration of local lithium loss and material loss causes rapid local degradation. Battery cell designers can improve cycle life by homogeneous pressure distribution in the cell and using negative active materials that are resilient to elevated discharge potentials such as improved carbons or lithium titanate. Also, a sufficiently oversized negative electrode and suitable electrolyte additives can help to avoid lithium plating. When packs are designed, care must be taken not to exert local pressure on parts of cells and to avoid both very high and low states of charge. In the second part of this dissertation the resilience of cylindrical and pouchbag cells to shocks and different vibrations was investigated. Stresses inflicted by vibration and shock tests according to the widely recognized UN38.3 transport test were compared to a long-time test that exposed cells to a 186 days long ordeal of sine sweep vibrations with a profile based on real-world applications. All cells passed visual and electric inspection performed by TU M{\"u}nchen after the vibration tests. Only cylindrical cells subjected to long-term vibrations in axial direction showed an increase in impedance and a loss of capacity that could be recuperated in part. The detailed analyses presented in this thesis gave more details on the damages inflicted by vibrations and shocks and revealed drastic damages in some cases. In cylindrical cells, only movement in axial direction caused damage. Long term vibrations were found to be especially detrimental. No damage whatsoever could be detected for pouch cells, regardless of the test protocol and the direction of movement. The extreme resilience of pouchbag cells shows that the electrode stack of lithium-ion cells is resistant to vibrations, and that damages are caused by design imperfections that can be improved at low cost. The findings of this work, and the general state of research show that it is most crucial to control the lithiation and thus potential of the graphite electrode. In the last part of this work, a new, direct method for charge estimation based on changing transmission is presented. A correlation between transmission of short ultrasonic pulses and state of charge is found. This new technology allows direct measurement of the state of charge. The method is demonstrated for batteries with different positive active materials, showing its versatility. As the observed changes can be traced to the lithiation of graphite, it can be determined without a reference electrode. Already at this early stage of development, the found correlations allow estimation of state of charge. The present hysteresis in the signal height of the slow wave, which is unneglectable especially during discharging at higher currents, will be subject to further investigation. The observed effects can be explained by effects on different length scales. Biot's theory explains the second wave's slowness based on the active material particles size in the range of 0.01 mm and electrolyte-filled pores. Lithiation of graphite changes the porosity of the electrode and thereby the velocity and wavelength of the impulse. When the wavelength approaches the length scale of the layers, 0.1 mm, scattering effects dampen the transmitted signal. Finally, the wavelength of the pulse should be shorter than the transducers diameter to obtain a homogeneous wave front. To conclude, the new method allows the control of each individual cell in a pack independent from the electrical connections of the cells. As the method shows great promise, further studies regarding factors such as long-term behavior, temperature and current rates should be conducted. In this thesis hysteresis was observed and a deeper understanding of the reasons behind it may allow further improvements of measurement precision.}, subject = {Lithium-Ionen-Akkumulator}, language = {en} } @phdthesis{Roeding2018, author = {R{\"o}ding, Sebastian}, title = {Coherent Multidimensional Spectroscopy in Molecular Beams and Liquids Using Incoherent Observables}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-156726}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2018}, abstract = {Das Ziel der vorliegenden Arbeit war die Umsetzung einer experimentellen Herangehensweise, welche die koh{\"a}rente zweidimensionale (2D) Spektroskopie an Proben in unterschiedlichen Aggregatzust{\"a}nden erm{\"o}glicht. Hierzu wurde zun{\"a}chst ein Aufbau f{\"u}r fl{\"u}ssige Proben realisiert, in welchem die emittierte Fluoreszenz als Messsignal zur Aufnahme der 2D Spektren genutzt wird. Im Gegensatz zu dieser bereits etablierten Methode in der fl{\"u}ssigen Phase stellt die in dieser Arbeit außerdem vorgestellte 2D Spektroskopie an gasf{\"o}rmigen Proben in einem Molekularstrahl einen neuen Ansatz dar. Hierbei werden zum ersten Mal Kationen mittels eines Flugzeitmassenspektrometers als Signal verwendet und somit ionen-spezifische 2D Spektren isolierter Molek{\"u}le erhalten. Zus{\"a}tzlich zu den experimentellen Entwicklungen wurde in dieser Arbeit ein neues Konzept zur Datenerfassung in der 2D Spektroskopie entworfen, welches mit Hilfe einer optimierten Signalabtastung und eines Compressed-Sensing Rekonstruktionsalgorithmus die Aufnahmezeit der Daten deutlich reduziert. Charakteristisch f{\"u}r die in dieser Arbeit eingesetzte Variante der 2D Spektroskopie ist die Verwendung einer phasenkoh{\"a}renten Sequenz bestehend aus vier Laserimpulsen in einer kollinearen Laserstrahlgeometrie zur Anregung der Probe. Diese Impulssequenz wurde durch einen Laserimpulsformer erzeugt, der durch {\"A}nderung der relevanten Laserimpulsparameter mit der Wiederholrate des Lasers eine schnelle Datenerfassung erm{\"o}glicht. Die Antwort der Probe auf diese Anregung wurde durch inkoh{\"a}rente Observablen gemessen, welche proportional zur Population des angeregten Zustandes sind, wie zum Beispiel Fluoreszenz oder Ionen. Um aus diesem Signal w{\"a}hrend der Datenanalyse die gew{\"u}nschten nichtlinearen Beitr{\"a}ge zu extrahieren, wurde die Messung mit verschiedenen Kombinationen der relativen Phase zwischen den Laserimpulsen wiederholt ("Phase Cycling"). Der Aufbau zur 2D Spektroskopie in fl{\"u}ssiger Phase mit Fluoreszenz-Detektion wurde an Hand von 2D Spektren des Laserfarbstoffes Cresyl Violett charakterisiert. Hierbei wurden Oszillationen in verschiedenen Bereichen des 2D Spektrums beobachtet, welche durch vibronische Koh{\"a}renzen hervorgerufen werden und mit fr{\"u}heren Beobachtungen in der Literatur {\"u}bereinstimmen. Mit dem gleichen Datensatz wurde im n{\"a}chsten Schritt das neue Konzept zur optimierten Datenerfassung demonstriert. Um ein optimiertes Schema f{\"u}r die Signalabtastung zu finden, wurde ein genetischer Algorithmus implementiert, wobei nur ein Viertel der eigentlichen Datenpunkte zur Messwerterfassung verwendet werden sollte. Dies reduziert die Zeitdauer der Datenerfassung auf ein Viertel der urspr{\"u}nglichen Messzeit. Die Rekonstruktion des vollst{\"a}ndigen Signales erfolgte mit Hilfe einer neuartigen, kompakten Darstellung von 2D Spektren basierend auf der von Neumann Basis. Diese Herangehensweise ben{\"o}tigte im Vergleich zur {\"u}blicherweise verwendeten Fourier Basis nur ein Sechstel der Koeffizienten um das Signal vollst{\"a}ndig darzustellen und erm{\"o}glichte so die erfolgreiche Rekonstruktion der Oszillationen in Cresyl Violett aus einem reduzierten Datensatz. Mit Hilfe der neuartigen koh{\"a}renten 2D Spektroskopie an Molekularstrahlen wurden {\"U}berg{\"a}nge von hoch angeregten Rydberg-Zust{\"a}nden ins ionische Kontinuum in Stickstoffdioxid untersucht. Als dominierender Beitrag stellte sich hierbei der {\"U}bergang in auto-ionisierende Zust{\"a}nde heraus. Ein wesentlicher Vorteil der Datenerfassung {\"u}ber ein Flugzeitmassenspektrometer ist die M{\"o}glichkeit der gleichzeitigen Aufnahme von 2D Spektren der Edukte und Produkte einer chemischen Reaktion. Dies wurde in Experimenten zur Mehrphotonenionisation gezeigt, in denen deutliche Unterschiede in den 2D Spektren des Stickstoffdioxid-Kations und des Stickstoffmonoxid-Fragmentes sichtbar wurden, welche auf unterschiedliche Antwortfunktionen zur{\"u}ckzuf{\"u}hren sind. Die in dieser Arbeit entwickelten experimentellen Techniken erm{\"o}glichen die schnelle Aufnahme von 2D Spektren f{\"u}r Proben in unterschiedlichen Aggregatzust{\"a}nden und erlauben einen zuverl{\"a}ssigen, direkten Vergleich der Ergebnisse. Sie sind deshalb ein Wegbereiter f{\"u}r zuk{\"u}nftige Untersuchungen der Eigenschaften quantenmechanischer Koh{\"a}renzen in photophysikalischen Prozessen oder w{\"a}hrend photochemischer Reaktionen in unterschiedlichen Aggregatzust{\"a}nden.}, subject = {Femtosekundenspektroskopie}, language = {en} } @phdthesis{Hochrein2018, author = {Hochrein, Thomas}, title = {Terahertz-Spektroskopie: Systementwicklung und Einsatz in der Polymeranalytik}, edition = {1. Auflage}, publisher = {W{\"u}rzburg University Press}, address = {W{\"u}rzburg}, isbn = {978-3-95826-090-0 (Print)}, doi = {10.25972/WUP-978-3-95826-091-7}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-163473}, school = {W{\"u}rzburg University Press}, pages = {xi, 194}, year = {2018}, abstract = {Die zeitaufgel{\"o}ste Terahertz-Spektroskopie erzielte in den letzten 20 Jahren erhebliche Entwicklungsfortschritte. Aber auch davor haben bereits Untersuchungen der dielektrischen Eigenschaften in diesem Spektralbereich mit herk{\"o}mmlichen Spektrometern unter anderen Termini stattgefunden. Viele Anwendungsfelder der Terahertz-Zeitbereichsspektroskopie sind noch unzureichend erforscht, weshalb in dieser Arbeit der Einsatz in der Polymeranalytik und prim{\"a}r an Polyamiden n{\"a}her untersucht wird. Außerdem weist die Terahertz-Systemtechnik f{\"u}r koh{\"a}rente Messungen noch erhebliche Verbesserungspotenziale auf. Im Rahmen dieser Arbeit wurde daher das neue Verfahren Optical Sampling by Laser Cavity Tuning (OSCAT) entwickelt. Es erm{\"o}glicht auf elegante Weise eine variable Zeitverz{\"o}gerung von Pulsfolgen, wie sie in Terahertz-Zeitbereichsspektrometern erforderlich ist. Dabei wird die M{\"o}glichkeit ver{\"a}nderbarer Repetitionsrate bei Ultrakurzpulslasern genutzt. Die Vorteile des OSCAT-Verfahrens, wie z. B. Skalierbarkeit, Robustheit, großer Messbereich und Messgeschwindigkeit, sowie die Funktion werden in dieser Arbeit sowohl theoretisch als auch experimentell vorgestellt und diskutiert. Erste Terahertz-Messungen an polymeren Schmelzen demonstrieren potenzielle Anwendungsgebiete f{\"u}r Terahertz-Spektrometer. Der Rezepturanteil und Zerst{\"o}rungsgrad eingebrachter F{\"u}llstoffe kann sehr gut {\"u}ber den Brechungsindex bestimmt werden. Die Ergebnisse zeigen außerdem ein stark temperaturabh{\"a}ngiges Verhalten polarer und unpolarer Polymere. Neben der Auswirkung der temperaturinduzierten Dichte{\"a}nderung auf den Brechungsindex konnte insbesondere bei Polyamiden ein starker Anstieg der Absorption mit zunehmender Temperatur nachgewiesen werden. Deshalb wurden die Absolutwerte des Brechungsindex und Absorptionskoeffizienten im niederfrequenten Terahertz-Spektralbereich tiefergehend untersucht. Es zeigte sich, dass der Brechungsindex polarer Polymere aus einem polaren und unpolaren Anteil besteht. Der unpolare Anteil wird prim{\"a}r durch die Material- bzw. Amidgruppendichte bestimmt. Der polare Anteil wird durch das inter- und intramolekulare Schwingungsverhalten bzw. dessen resultierenden Absorptionsbanden beeinflusst. Diese Schwingungsmoden wurden daher mittels breitbandiger Spektroskopie in abgeschw{\"a}chter Totalreflexion (ATR) an unterschiedlichen Polyamiden aufgenommen. Simulationsrechnungen mit Lorentz-Oszillatoren zeigen, wie bedeutsam eine kritische Diskussion absoluter Absorptionswerte aus solchen ATR-Messungen ist. Die ermittelten Ursachen sind {\"A}nderungen des Brechungsindex der Probe infolge von Temperatur{\"a}nderung sowie Dispersion durch Schwingungsmoden - auch weit abseits des Bandenmaximums. Die gemessenen Schwingungsmoden wurden anhand quantenmechanischer ab-inito Berechnungen der Molek{\"u}lketten und -cluster analysiert und mit Literaturangaben abgeglichen. Verschiedene Schwingungen konnten hierbei im Terahertz-Spektralbereich bei unterschiedlichen {\alpha}- und {\gamma}-Polyamiden ausgemacht werden. Sie erweisen sich als sehr komplex und erstrecken sich meist {\"u}ber die gesamte Molek{\"u}lkette. Schwingungen einzelner Atome oder Gruppen sind meist mit umfangreichen Ausgleichsbewegungen des Molek{\"u}lr{\"u}ckgrats gekoppelt. Insbesondere phononenartige Schwingungen konnten hierbei im Vergleich zu bisherigen Publikationen sehr pr{\"a}zise beschrieben werden.}, subject = {FIR-Spektroskopie}, language = {de} } @phdthesis{Hegmann2017, author = {Hegmann, Jan}, title = {Lichtstreuende Sol-Gel-Schichten f{\"u}r die Si- D{\"u}nnschichtphotovoltaik}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-155815}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2017}, abstract = {Ziel dieser Arbeit war es, ein Schichtsystem auf Basis des Sol-Gel-Prozesses zu entwickeln, um Lighttrapping in Si-D{\"u}nnschichtsolarzellen zu erzeugen. Die Grundlage dieses Schichtsystems bilden SiO2-Partikel, die {\"u}ber den St{\"o}ber-Prozess hergestellt werden. Es zeigte sich, dass sich die Rauheit und der Haze der Schichten {\"u}ber die Partikelgr{\"o}ße und Schichtdicke einstellen lassen. Um die mechanische Stabilit{\"a}t der reinen St{\"o}ber-Schichten zu verbessern, kamen verschiedene Binder zum Einsatz. Beste Ergebnisse zeigten Binder basierend auf l{\"o}slichen Vorstufenpulvern, da diese dem St{\"o}ber-Sol beigemischt werden konnten und so Binder und Partikel gleichzeitig aufgebracht werden konnten. Auf diese Weise entstehen mechanisch stabile, lichtstreuende Schichten. Zum Einsatz kam zun{\"a}chst ein TiO2-Binder. Durch eine anschließende Gl{\"a}ttung der St{\"o}ber-TiO2-Streuschichten mit SiO2 entsteht eine defektfreie, aber dennoch raue Oberfl{\"a}che. Zus{\"a}tzlich wird ein betr{\"a}chtlicher Teil des Lichts in große Winkel gestreut. Es konnte gezeigt werden, dass sich auf den SiO2-gegl{\"a}tteten St{\"o}ber-TiO2-Streuschichten ZnO:Al deponieren l{\"a}sst, wobei die elektrischen Eigenschaften von der Dicke der Gl{\"a}ttung abh{\"a}ngen. Auch die elektrischen Eigenschaften der Si-D{\"u}nnschichtsolarzellen h{\"a}ngen von der Gl{\"a}ttung bzw. der Dicke der Gl{\"a}ttung ab. Dies gilt insbesondere f{\"u}r die von der Materialqualit{\"a}t abh{\"a}ngigen Parameter F{\"u}llfaktor FF und offen Klemmenspannung VOC. Insgesamt fallen die Parameter jedoch noch gegen{\"u}ber Referenzzellen auf ge{\"a}tztem Frontkontakt zur{\"u}ck. Vor allem aber wurde die hohe Zellreflexion aufgrund der Glas-TiO2-Grenzfl{\"a}che als prim{\"a}res Problem identifiziert. Dennoch konnte bei einer Gl{\"a}ttungsdicke von 200 nm sehr gutes Lighttrapping beobachtet werden. Verantwortlich hierf{\"u}r ist sehr wahrscheinlich die Großwinkelstreuung der St{\"o}ber-TiO2-Streuschichten. Um die Zellreflexion zu verringern, wurde der Brechungsindex des Binders und der Gl{\"a}ttungsschichten an den Stack aus Substrat, Streuschicht und ZnO:Al-Schicht angepasst. Idee war es, durch Einbringen eines Al2O3-Vorstufenpulvers eine niedrigbrechende Komponente bereitzustellen, um durch Mischung von Al2O3- und TiO2-Vorstufenpulver freie Hand {\"u}ber den Brechungsindex des Binders und der Gl{\"a}ttung zu erhalten. Da sich das Volumenverh{\"a}ltnis von SiO2-Partikeln zu Binder bei verschiedenen Al2O3-TiO2-Verh{\"a}ltnissen nur schwer bestimmen l{\"a}sst, wurde lediglich ein reiner Al2O3-Binder in den Streuschichten eingesetzt. Die Einstellung des Brechungsindex beschr{\"a}nkte sich allein auf die Gl{\"a}ttungsschichten. Um St{\"o}ber-Al2O3-Streuschichten mit hoher Rauigkeit und geringen Defekten zu erzielen, muss das Binder-zu-Partikel-Verh{\"a}ltnis angepasst werden. Beste Ergebnisse ergaben sich bei einem Al2O3-Gehalt von 2\% im Sol. Aufgrund der hohen Rauigkeit besitzen die Streuschichten einen hohen Haze und wegen des geringen Brechungsunterschied zwischen Glas und Binder eine hohe Transmission. Die Gl{\"a}ttung der Streuschichten im Al2O3-TiO2-System ist nur mit Hilfe einer zus{\"a}tzlichen SiO2-Gl{\"a}ttungsschicht und einer reduzierten Dicke auf 50 nm m{\"o}glich. Auf den reinen defektreichen Streuschichten tendieren die Al2O3-TiO2-Schichten selbst zu Rissbildung. Zur Untersuchung der ZnO:Al-Deposition wurde eine Gl{\"a}ttungsdicke von 200 nm gew{\"a}hlt. Die erwies sich als zu gering. Die aufgebrachten ZnO:Al-Schichten wiesen gr{\"o}ßere Poren und kleinere Oberfl{\"a}chendefekte auf. Die Anpassung des Brechungsindex der Gl{\"a}ttungsschichten an die ZnO:Al-Schicht erwies sich nicht als vorteilhaft. Die reine Al2O3-Gl{\"a}ttung zeigt auch nach der ZnO:Al-Deposition die h{\"o}chste Transmission. Die Winkelverteilung des Streulichts der St{\"o}ber-Al2O3-Streuschichten ist gegen{\"u}ber den St{\"o}ber-TiO2-Streuschichten zu kleineren Winkeln verschoben. Dennoch wird ein gr{\"o}ßerer Anteil des Lichts in große Winkel gestreut, als es bei der ge{\"a}tzten ZnO:Al-Referenz der Fall ist. Trotz der Defekte in den ZnO:Al-Schichten konnten auf den St{\"o}ber-Al2O3-Streuschichten funktionierende Tandemzellen hergestellt werden. Der F{\"u}llfaktor und die offene Klemmenspannung fallen nur geringf{\"u}gig hinter die der Referenzzelle zur{\"u}ck. In der Kurzschlussstromdichte machen sich die verringerte Zellreflexion und das sehr gute Lighttrapping bemerkbar, so dass das Niveau der Referenz erreicht werden konnte. Zu beachten ist allerdings, dass gerade im langwelligen Lighttrapping-Spektralbereich die gleiche EQE erreicht wurde, trotz immer noch leicht erh{\"o}hter Zellreflexion. Die letzte Versuchsreihe konnte zeigen, dass die entwickelten Schichten sich sehr gut zur Erzeugung von Lighttrapping in Si-D{\"u}nnschichtsolarzellen eignen.}, subject = {D{\"u}nnschichtsolarzelle}, language = {de} } @phdthesis{Schott2018, author = {Schott, Sebastian}, title = {Identification of trihalide photodissociation patterns by global vibrational wavepacket analysis of broadband magic-angle transient absorption data}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-159677}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2018}, abstract = {The invention of laser pulse shapers allowed for various quantum control experiments, where a chemical reaction is guided by specifically tailored laser pulses. However, despite of the prominent role of the liquid phase in chemistry, no successful attempt for controlling the selectivity of a bond-fission reaction has yet been reported in this state of matter. Promising candidates for such an experiment are C\$_{\infty\mathrm{v}}\$-symmetric trihalide anions with two different chemical bonds like \$\ce{I2Cl-}\$, because these molecules notionally offer the most simplest selectivity-control scenario of breaking either the one or the other bond and they are expected to dissociate under ultraviolet (UV) irradiation like it is known for the most-studied trihalide \$\ce{I3-}\$. In order to investigate in this thesis the possibility that the dissociation reaction of such trihalides branches into two different photofragments, the ultrafast photodissociation dynamics of \$\ce{I3-}\$, \$\ce{Br3-}\$, \$\ce{IBr2-}\$ and \$\ce{ICl2-}\$ (point group D\$_{\infty\mathrm{h}}\$) as well as of \$\ce{I2Br-}\$ and \$\ce{I2Cl-}\$ (point group C\$_{\infty\mathrm{v}}\$) in dichloromethane solution were measured with broadband transient absorption spectroscopy in magic-angle configuration. The identification of the reaction pathway(s) relies on vibrational wavepacket oscillations, which survive the dissociation process and therefore carry not only informations about the reactant trihalides but also about the fragment dihalides. These characteristic vibrational wavenumbers were extracted from the measured transient absorption spectra by globally fitting the population dynamics together with the wavepacket dynamics. Until recently, such a combined model function was not available in the well-established fitting tool Glotaran. This made it inevitable to develop a custom implementation of the underlying variable-projection fitting algorithm, for which the computer-algebra software Mathematica was chosen. Mathematica's sophisticated built-in functions allow not only for a high flexibility in constructing arbitrary model functions, but also offer the possibility to automatically calculate the derivative(s) of a model function. This allows the fitting procedure to use the exact Jacobian matrix instead of approximating it with the finite difference method. Against the expectation, only one of the two thinkable photodissociation channels was found for each of the investigated C\$_{\infty\mathrm{v}}\$ trihalides. Since the photofragments recombine, their absorption signal as well as the reactant ground state bleach recover. This happens in a biexponential manner, which in the case of \$\ce{I3-}\$ was interpreted by Ruhman and coworkers with the direct formation of a neutral dihalogen fragment \$\ce{I2}\$ beside the negatively charged dihalide fragment \$\ce{I2-}\$. In this thesis, such a direct reaction channel was not found and instead the fast component of the biexponential decay is explained with vibrational excess energy mediating the recombination-preceding electron transfer process \$\ce{I2- + I -> I2 + I-}\$, while the slow component is attributed to cooled-down fragments. In addition to the trihalide experiments, the possibility of a magic-angle configuration for polarization-shaping control experiments was theoretically investigated in this thesis by deriving magic-angle conditions for the third-order electric-dipole response signal of arbitrarily polarized laser pulses. Furthermore, the subtleties of anisotropy signals violating the well-known range of \numrange{-0.2}{0.4} were studied.}, subject = {Femtosekundenspektroskopie}, language = {en} } @phdthesis{Schaupp2022, author = {Schaupp, Thomas}, title = {Quantendynamik korrelierter Elektronen- und Kernbewegung}, doi = {10.25972/OPUS-23774}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-237743}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2022}, abstract = {Im Rahmen dieser Arbeit werden unterschiedliche Aspekte der korrelierten Elektronen-Kerndynamik, anhand verschiedener Modellsysteme untersucht. Dabei wird vor allem auf den Vergleich numerisch exakter und approximativer Methoden zur Beschreibung der Wellenpaketdynamik eingegangen, wobei bei letzterem das Augenmerk auf der Born-Oppenheimer (BO) N{\"a}herung liegt. Die verwendeten Modellsysteme erlauben es, die gekoppelte Elektronen-Kern-Dynamik exakt zu beschreiben. Die daraus gewonnenen Ergebnisse dienen als Referenz f{\"u}r den Vergleich mit den N{\"a}herungsmethoden. Im ersten Teil der Arbeit wird die Dynamik eines Wellenpakets in der Umgebung einer Konischen-Durchschneidung (CI) untersucht, wobei die Beschreibung des Wellenpakets quantenmechanisch und durch die klassische Mechanik im Phasenraum erfolgt. Im zweiten Teil wird die Wahrscheinlichkeitsflussdichte untersucht. Zuerst wird ein Fall konstruiert, in welchem die Bewegung im elektronischen Grundzustand stattfindet, sodass die Bedingungen der BO N{\"a}herung erf{\"u}llt sind. Dabei wird vor allem auf das Verschwinden der elektronischen Wahrscheinlichkeitsflussdichte innerhalb der BO N{\"a}herung eingegangen. Im weiteren Verlauf werden die Flussdichten in der Umgebung einer CI untersucht, wobei unterschiedliche Situationen modelliert werden. Im dritten Teil wird die Berechnung des elektronischen Impulserwartungswerts innerhalb der BO N{\"a}herung untersucht. Dieser verschwindet innerhalb der BO N{\"a}herung, wenn man diesen direkt berechnet (Geschwindigkeitsform), w{\"a}hrend man {\"u}ber das Ehrenfest Theorem (L{\"a}ngenform) sehr gute Werte erh{\"a}lt. Im vierten Teil wird eine neue Flussdichte, die Translationsflussdichte, vorgestellt. Diese ergibt sich aus der {\"U}berlegung, dass die Geschwindigkeitsform des Impulserwartungswerts durch die Wahrscheinlichkeitsflussdichte ausgedr{\"u}ckt werden kann. Demnach muss auch die L{\"a}ngenform einer Flussdichte entsprechen und man erh{\"a}lt die Translationsflussdichte.}, subject = {Quantenmechanik}, language = {de} } @phdthesis{Hirsch2021, author = {Hirsch, Florian}, title = {IR/UV Double-Resonance Spectroscopy of Reactive Hydrocarbon Species and their Reaction Products in Cold Molecular Jets}, doi = {10.25972/OPUS-25175}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-251755}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2021}, abstract = {Reactive hydrocarbon species are important in a multitude of different scientific areas. In this thesis, the vibrational spectra of hydrocarbon radicals, biradicals and their reaction product have been studied in a gas-phase environment. The specific molecules investigated here, are of particular importance in the field of combustion and astrochemistry. They were produced from suitable precursors in a pyrolytically heated micro-reactor and subsequently seeded in an appropriate carrier gas. As methodology, IR/UV ion dip spectroscopy has been utilized, which delivers massselected gas-phase IR spectra of all ionizable species detectable in the molecular beam. These, with the help of DFT calculations, allow for determination of the fingerprint IR spectra, identification of mass carriers and formulation of potential reaction mechanisms. All studies have been conducted in collaboration with the group of Prof. Dr. Anouk M. Rjis and the necessary potent IR radiation has been provided by the free-electron laser FELIX. Thus, the IR/UV measurements have been executed at the FELIX Laboratory of the Radboud University in Nijmegen. The first study presented in this thesis is the investigation of ortho-benzyne in Chapter 3.1. This molecule is of particular interest due to its uncommon electronic structure and its role in high-temperature reactions. Although, the infrared spectrum of o-C6H4 was not accessible, a number of reaction products were identified via their fingerprint spectra. Masses in the range from 78 - 228 were assigned to their respective carrier. The identified species include typical PAHs like naphthalene, phenanthrene, up to triphenylene. The identified masses further suggest a PAH growth heavily influenced by diradical 1,4-cycloaddition followed by fragmentation, as well as by classical HACA- and PAC-like mechanisms. These results were augmented by threshold photoionization measurements from Engelbert Reusch, who identified lighter reaction products, which have insufficient IR absorption or unsuitable ionization characteristics to be identified in the IR/UV experiment. An interesting observation is the identification of m/z = 152. This carrier has been assigned differently by the IR and TPES experiments. Whereas the IR spectrum clearly identifies the species as 2-ethynylnaphthalene, the TPES evidently is in great agreement with biphenylene. This is a good example how different experimental methodologies can benefit from each other to gain a deeper insight into the actual science of a particular system. Probably, the prime example for an aromatically resonance stabilized radical is benzyl. This radical is of high importance for many combustion studies, as it represents the primary high-temperature decomposition product of toluene. The goal of the study was the identification of the benzyl self reaction products and the results are discussed in Section 3.2. The radical was pyrolytically produced by its respective nitrite precursor. The mass spectrum showed that the benzyl self reaction formed two products with C11 and three with C14 constitution. All mass peaks were evenly spaced by two mass units, respectively, which suggests a close relation in formation. Indeed, the C11 products were identified as diphenylmethane and fluorene, which are simply connected via cyclization. The heaviest product was identified as phenanthrene, which is formed via the cyclization of bibenzyl to 9,10-dihydrophenanthrene and subsequent elimination of hydrogen. This result was quiet interesting as the intermediate of this reaction was often assumed to be stilbene, which was not observed in the study. Hence, the reaction seems to undergo cyclization first before phenanthrene is finally formed via hydrogen elimination. Expanding the molecular frame of benzyl by an additional methyl group leads to the xylyl radicals and its decomposition product the xylylenes. Also important in combustion research, xylyl radicals represent the preferred decomposition products of xylene, a frequently used anti-knock agent in modern gasoline blends. After further hydrogen elimination the xylyl radicals can then form their respective xylylenes. The results of the xylyl experiments are discussed in Section 3.3. Here the gas-phase vibrational spectrum in the fingerprint region for all three isomers has been recorded for the first time in isolation. Although, all isomers have a very similar structure and symmetry, and consequently similar vibrational bands, the resolution of the experimental data was exceedingly sufficient for a clear assignment. Additionally, the dimerization products of meta- and para-xylyl could also be identified. A similar approach was taken to determine the fingerprint spectra for the xylylenes. Here, only para-xylylene could be unambiguously identified as the carrier of mass 104. For both ortho- and meta-xylylene precursors, only isomerization products were observed as the carriers of mass 104; benzocyclobutene and styrene, respectively. A possible explanation is elaborated upon in the troubleshooting Sec- tion 3.4.3.5. In the final experimental section a study on the decomposition of phthalide is presented. The objective of this experiment was mainly focused around the formation of C7 species, particularly the fulvenallenyl radical C7H5. In fact, the first experimental fingerprint spectrum of isolated C7H5 in the gas-phase was measured and is displayed in Fig. 3.45. Furthermore, the experiment demonstrates that the pyrolysis products of phthalide are excellent soot precursors, as many heavier reaction products have been identified. These include typical PAH species like naphthalene and phenanthrene as well as their methylated isomers. A large number of molecules with terminal ethynyl moieties indicate a strong influence of HACA growth in the experimental environment. However, many formation pathways of products have been discussed, which are formed involving experiment specific species, like C5H5 and C7H5, and often include expansion steps from 5- to 6-membered rings.}, subject = {Infrarotspektroskopie}, language = {en} } @phdthesis{Draeger2020, author = {Draeger, Simon}, title = {Rapid Two-Dimensional One-Quantum and Two-Quantum Fluorescence Spectroscopy}, doi = {10.25972/OPUS-19816}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-198164}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2020}, abstract = {In den letzten zwei Jahrzehnten hat sich die koh{\"a}rente mehrdimensionale Femtosekunden- Spektroskopie zu einem leistungsstarken und vielseitigen Instrument zur Untersuchung der chemischen Dynamik einer Vielzahl von Quantensystemen entwickelt. Die Kombination von transienten Informationen, die der Anrege-Abrage-Spektroskopie entsprechen, mit Informationen zur Kopplung zwischen energetischen Zust{\"a}nden und der Systemumgebung erm{\"o}glicht einen umfassenden Einblick in atomare und molekulare Eigenschaften. Viele experimentelle 2D-Aufbauten verwenden den koh{\"a}renzdetektierten Ansatz, bei dem nichtlineare Systemantworten als koh{\"a}rente elektrische Felder emittiert und r{\"a}umlich getrennt von den Anregungspulsen detektiert werden. Als Alternative zu diesem experimentell anspruchsvollen Ansatz wurde die populationsbasierte 2D-Spektroskopie etabliert. Hier wird die koh{\"a}rente Information in den Phasen einer kollinearen Anregungspulsfolge codiert und aus inkoh{\"a}renten Signalen wie Fluoreszenz {\"u}ber Phase Cycling extrahiert. Grunds{\"a}tzlich kann durch die Verwendung von Fluoreszenz als Observable eine Sensitivit{\"a}t bis zum Einzelmolek{\"u}lniveau erreicht werden. Ziel dieser Arbeit war die Realisierung eines pulsformergest{\"u}tzten vollst{\"a}ndig kollinearen fluoreszenzdetektierten 2D-Aufbaus und die Durchf{\"u}hrung von Proof-of- Principle-Experimenten in der Fl{\"u}ssigphase. Dieser inh{\"a}rent phasenstabile und kompakte Aufbau wurde in Kapitel 3 vorgestellt. Der verwendete Pulsformer erm{\"o}glicht eine Amplituden- und Phasenmodulation von Schuss zu Schuss. Zwei verschiedene Arten von Weißlichtquellen wurden angewendet und hinsichtlich ihrer jeweiligen Vorteile f{\"u}r die 2D-Fluoreszenzspektroskopie bewertet. Eine Vielzahl von Artefaktquellen, die mit dem vorliegenden Aufbau auftreten k{\"o}nnen, wurden diskutiert und Korrekturschemata und Anweisungen zur Vermeidung dieser Artefakte bereitgestellt. In Kapitel 4 wurde der Aufbau anhand einer Vierpulssequenz mit Cresylviolett in Ethanol demonstriert. Es wurde ein detailliertes Datenerfassungs- und Datenanalyseverfahren vorgestellt, bei dem Phase Cycling zur Extraktion der nichtlinearen Beitr{\"a}ge verwendet wird. Abh{\"a}ngig vom Phase Cycling-Schema ist es m{\"o}glich, alle nichtlinearen Beitr{\"a}ge in einer einzigen Messung aufzudecken. Literaturbekannte Oszillationen von Cresylviolett w{\"a}hrend der Populationszeit konnten reproduziert werden. Aufgrund der Messung in einer Umgebung im Rotating Frame und einer 1 kHz Schuss-zu-Schuss Pulsinkrementierung war es m{\"o}glich, ein 2D-Spektrum f{\"u}r eine Populationszeit in 6 s zu erhalten. Eine Fehlerevaluierung hat gezeigt, dass eine zehnfache Mittelwertbildung (1 min) ausreicht, um eine mittlere quadratische Abweichung von < 0:05 gegen� uber einer 400-fachen Mittelwertbildung zu erhalten, was beweist, dass das verwendete Messschema gut geeignet ist. Die Realisierung des ersten experimentellen fluoreszenzdetektierten 2Q-2D-Experiments und der erste experimentelle Zugang zum theoretisch vorhergesagten 1Q-2Q-Beitrag wurden in Kapitel 5 vorgestellt. Zu diesem Zweck wurde eine Dreipulssequenz auf Cresylviolett in Ethanol angewendet und die experimentellen Ergebnisse wurden mit Simulationen eines einfachen Sechs-Level-Systems verglichen. Im Gegensatz zur koh{\"a}renzdetektierten 2Q-2D-Spektroskopie sind bei dem vorgestellten Aufbau keine nichtresonanten L{\"o}sungsmittelsignale und Streuungsbeitr{\"a}ge sichtbar und es ist kein zus{\"a}tzliches Phasing-Verfahren erforderlich. Durch eine Kombination aus Experimenten und systematischen Simulationen wurden Informationen {\"u}ber die Relaxation der L{\"o}sungsmittelh{\"u}lle und die Korrelationsenergie gewonnen. Auf der Basis von Simulationen wurden Effekte der Pfadausl{\"o}schung diskutiert, die darauf schließen lassen, dass die 1Q-2Q-2D-Spektroskopie m{\"o}glicherweise die quantitative Analyse f{\"u}r molekulare Systeme erleichtert, die eine starke nichtstrahlende Relaxation aus h{\"o}heren elektronischen Zust{\"a}nden aufweisen. Zusammenfassend ist es mit der vorgestellten Methode m{\"o}glich, alle nichtlinearen Beitr{\"a}ge mit einer schnellen Datenaufnahme und einem einfach einzurichtenden Aufbau zu erfassen. Die gezeigten Proof-of-Principle-Experimente stellen eine Erweiterung der 2D-Spektroskopie-Werkzeugpalette dar und bieten eine fundierte Grundlage f{\"u}r zuk{\"u}nftige Anwendungen wie mehrdimensionale Spektroskopie, mehrfarbige 2D-Spektroskopie oder die Kombination von simultanen Fl{\"u}ssig- und Gasphasen-2D-Experimenten.}, subject = {Fluoreszenzspektroskopie}, language = {en} } @unpublished{FerschMalyRueheetal.2023, author = {Fersch, Daniel and Mal{\´y}, Pavel and R{\"u}he, Jessica and Lisinetskii, Victor and Hensen, Matthias and W{\"u}rthner, Frank and Brixner, Tobias}, title = {Single-Molecule Ultrafast Fluorescence-Detected Pump-Probe Microscopy}, doi = {10.25972/OPUS-31348}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-313485}, year = {2023}, abstract = {We introduce fluorescence-detected pump-probe microscopy by combining a wavelength-tunable ultrafast laser with a confocal scanning fluorescence microscope, enabling access to the femtosecond time scale on the micrometer spatial scale. In addition, we obtain spectral information from Fourier transformation over excitation pulse-pair time delays. We demonstrate this new approach on a model system of a terrylene bisimide (TBI) dye embedded in a PMMA matrix and acquire the linear excitation spectrum as well as time-dependent pump-probe spectra simultaneously. We then push the technique towards single TBI molecules and analyze the statistical distribution of their excitation spectra. Furthermore, we demonstrate the ultrafast transient evolution of several individual molecules, highlighting their different behavior in contrast to the ensemble due to their individual local environment. By correlating the linear and nonlinear spectra, we assess the effect of the molecular environment on the excited-state energy.}, subject = {Fluoreszenz}, language = {en} } @phdthesis{Reusch2021, author = {Reusch, Engelbert}, title = {Photoionisation von Biradikalen mit Synchrotronstrahlung}, doi = {10.25972/OPUS-24009}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-240098}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2021}, abstract = {Die vorliegenden Arbeit behandelt VUV Valenz-Photoionisations-Experimente in der Gasphase. Zun{\"a}chst wird die Photoionisation von stickstoffhaltigen Radikalen und deren Pyrolyseprodukten untersucht. Im Anschluss werden molekulare Biradikale betrachtet. Da in der Literatur bislang nur wenige solcher Biradikale als Intermediate experimentell zug{\"a}nglich waren, war es das Ziel dieser Arbeit, neue reaktive Spezies dieser Substanzklassen in der Gasphase zu isolieren und deren Struktur, Eigenschaften und Reaktivit{\"a}t besser zu verstehen. Im Mittelpunkt stehen dabei Intermediate, die als echte Biradikale, Biradikaloide oder Triplett Carbene auftreten. Zu letzteren z{\"a}hlen das Methylbismut sowie die Pentadiinylidene. Biradikale bilden in Verbrennungsprozessen sehr effizient Ruß(vorl{\"a}ufer), was anhand des ortho-Benz-ins dargelegt wurde, indem dessen Pyrolyseprodukte charakterisiert und m{\"o}gliche PAH-Bildungswege aufgezeigt wurden. Vakuum Flash Pyrolyse wurde verwendet, um in situ aus den geeigneten Vorl{\"a}ufermolek{\"u}len die radikalischen und biradikalischen Intermediate zu erzeugen. W{\"a}hrend f{\"u}r biradikalische Zwischenstufen meist spezielle Verbindungen als Vorl{\"a}ufer synthetisiert werden m{\"u}ssen, waren die verwendeten Vorl{\"a}ufer f{\"u}r die stickstoffhaltigen Radikale kommerziell erh{\"a}ltlich. Die reaktiven Spezies wurden alle mittels monochromatischer VUV Synchrotronstrahlung an der Swiss Light Source in Villigen/ Schweiz ionisiert. Die Ionisationsereignisse wurden mit der Schwellenphotoelektronen-Photoionen-Koinzidenz (TPEPICO) Technik detektiert und ausgewertet. Anhand der resultierenden massenselektiven Schwellenphotoelektronenspektren wurden die Ionisierungsenergien der (Bi)radikale bestimmt und die Schwingungsstruktur der jeweiligen Kationen analysiert. Die erhaltenen Spektren und Daten wurden in Zusammenarbeit mit der theoretischen Chemie interpretiert. Wichtige Erkenntnisse • Es wurde die Ionisierungsenergie der 2-, 3- und 4-Picolylradikale auf 7.70\pm 0.02 eV, 7.59\pm 0.01 eV und 8.01\pm 0.01 eV bestimmt. Diese wurden in der Pyrolyse selektiv aus ihren zugeh{\"o}rigen Picolylaminen erzeugt. Zudem wurde analog zum Benzyl-Radikal f{\"u}r alle drei Radikale eine ausgepr{\"a}gte Schwingungsprogression ermittelt, die der totalsymmetrischen Deformationsmode des aromatischen Rings entspricht. • Die Picolyl-Radikale dissoziieren in der Pyrolyse thermisch zu weiteren Produkten. Die Fragmentierung verl{\"a}uft dabei isomerenunabh{\"a}ngig {\"u}ber ein stickstoffhaltiges Siebenringintermediat, dem Azepinyl-Radikal. Der Fragmentierungsmechanismus wurde mit dem von Benzyl verglichen. Die gewonnenen Erkenntnisse haben Relevanz f{\"u}r Verbrennungsprozesse, beispielsweise von Biokraftstoffen.Im ersten Schritt entstehen vier Isomere, das Cyclopenta-1,4-dien-1-carbonitril, das Cyclopenta-1,3-dien-1-carbonitril, das 2-Ethynyl-1H-pyrrol und das3-Ethynyl-1H-pyrrol mit den zugeh{\"o}rigen Ionisierungsenergien von 9.25\pm 0.02 eV, 9.14\pm 0.02 eV, 7.99\pm 0.02 eV und 8.12\pm 0.02 eV. Durch einen zweiten H-Verlust konnte das Cyanocyclopentadienyl-Radikal mit einer Ionisierungsenergie f{\"u}r die zwei niedrigsten Zust{\"a}nde im Kation mit 9.07\pm 0.02 eV (T0) und 9.21\pm 0.02 eV (S1) untersucht werden. Weitere Pyrolyseprodukte, deren Ionisierungsenergien bereits literaturbekannt sind und die best{\"a}tigt wurden, sind das Cyclopentadienyl-Radikal, das Cyclopenta-1,3-dien, das Propargyl-Radikal, das Penta-1,3-diin und das Cyanopropenyl. • Das ortho-Benz-in wurde pyrolytisch aus dem selbst synthetisierten Benzocyclobutendion erzeugt und ein Schwellenphotoelektronenspektrum frei von St{\"o}rsignalen konnte aufgenommen werden. Mit Hilfe von Rechnungen aufCASPT2(11,14) Niveau, die neben dem elektronischen {\"U}bergang in den kationischen Grundzustand noch die {\"U}berg{\"a}nge in zwei weitere angeregte kationische Zust{\"a}nde beinhalten, wurde die Ionisierungsenergie im Vergleich zu fr{\"u}heren Experimenten auf 9.51 eV revidiert. Eine verdrillte Geometrie f{\"u}r den kationischen Grundzustand konnte erstmals nachgewiesen werden. Zus{\"a}tzlich wurden die offenkettigen Isomere cis- und trans-Hexa-1,5-diin-3-en im Spektrum detektiert und zugeordnet. • Die Auftrittsenergien aus der DPI des Vorl{\"a}ufermolek{\"u}ls Benzocyclobutendion betragen f{\"u}r den ersten CO-Verlust 9.62\pm 0.05 eV und f{\"u}r den zweiten CO-Verlust 12.14\pm 0.10 eV. Damit konnte {\"u}ber einen thermochemischen Kreisprozess eine Bindungsdissoziationsenergie f{\"u}r die Ph-CO Bindung im Benzoylkation von 2.52 eV berechnet werden. • Verschiedenen Pyrolyseprodukte des ortho-Benz-ins, wie Ethin, Buta-1,3-diin, Benzol, Biphenylen und 2-Ethinylnaphthalin, werden entweder in bimolekularen Reaktionen gebildet oder ortho-Benz-in fragmentiert unimolekular zu diesen. Die beiden kompetitiven Reaktionspfade tragen zur PAH-Bildung des ortho-Benz-ins bei. • Die Triplett-Carbene Pentadiinyliden, Methylpentadiinyliden und Dimethylpentadiinyliden wurden als Pyrolyseprodukt aus ihren zugeh{\"o}rigen Diazovorl{\"a}ufern identifiziert und die Ionisierungsenergien mit 8.36\pm 0.03 eV, 7.77\pm 0.04 eV und 7.27\pm 0.06 eV bestimmt. Jede Methylierung stabilisiert folglich das Carben. Zus{\"a}tzlich konnte ein weiteres C5H2 Isomer, das 3-(Didehydrovinyliden)cyclopropen, mit einer Ionisierungsenergie von 8.60\pm 0.03 eV charakterisiert werden. • Zwei bismuthaltige, reaktive Spezies, das Dimethylbismut-Radikal\cdot BiMe2 (IE = 7.27\pm 0.04 eV) und das Methylbismut-Carben :BiMe(IE = 7.88\pm 0.02 eV) wurden als Pyrolyseprodukte aus dem BiMe3 identifiziert. Beide Verbindungen zeigen eine ausgepr{\"a}gte Schwingungsstruktur, die der Bi-C Streckschwingung zugeordnet wurde. Weiterhin wurden elementares Bismut Bi und das Bismut-Dimer Bi2 nachgewiesen. • Die homolytische Dissoziation der ersten Me2Bi-CH3 Bindung im BiMe3 wurde untersucht und eine BDE von 210\pm 7 kJ/ mol bestimmt. Sie liegt um +15 \% bzw. +28 kJ/ mol {\"u}ber dem aus der Literatur abgesch{\"a}tzten Wert.}, subject = {Biradikal}, language = {de} } @phdthesis{Graeb2021, author = {Gr{\"a}b, Patrick}, title = {Physikalisch-chemische Methoden und Experimente f{\"u}r Unterricht und Lehramtsstudium}, doi = {10.25972/OPUS-24763}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-247636}, school = {Universit{\"a}t W{\"u}rzburg}, year = {2021}, abstract = {Die Lehre von physikalisch-chemischen Inhalten in der universit{\"a}ren Lehramtsausbildung und im gymnasialen Chemieunterricht ist herausfordernd. M{\"o}gliche Ursachen hierf{\"u}r sind das teils hohe Abstraktionsniveau und fehlende Messger{\"a}te. Im Rahmen dieser Arbeit wurden kosteng{\"u}nstige Messger{\"a}te entwickelt, mit denen Lernende in typische physikochemische Methoden und deren Anwendungen experimentell eingef{\"u}hrt werden k{\"o}nnen. Durch offen gestaltete und kontextbezogene Experimente zu Themenfeldern der Spektroskopie, Thermodynamik und Kinetik sollen Lernende einen ph{\"a}nomenologischen Zugang zur physikalischen Chemie finden. Durch eine entsprechende didaktische und experimentelle Aufarbeitung der Konzepte sollen insbesondere Sch{\"u}lerinnen und Sch{\"u}ler ohne gr{\"o}ßeres Vorwissen f{\"u}r physikalisch-chemische Inhalte im Sinne eines modernen und experimentell orientierten Chemieunterrichts begeistert werden.}, subject = {Hochschule}, language = {de} } @unpublished{TitovHumeniukMitric2020, author = {Titov, Evgenii and Humeniuk, Alexander and Mitric, Roland}, title = {Comparison of moving and fixed basis sets for nonadiabatic quantum dynamics at conical intersections}, series = {Chemical Physics}, journal = {Chemical Physics}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-198699}, year = {2020}, abstract = {We assess the performance of two different types of basis sets for nonadiabatic quantum dynamics at conical intersections. The basis sets of both types are generated using Ehrenfest trajectories of nuclear coherent states. These trajectories can either serve as a moving (time-dependent) basis or be employed to sample a fixed (time-independent) basis. We demonstrate on the example of two-state two-dimensional and three-state five-dimensional models that both basis set types can yield highly accurate results for population transfer at intersections, as compared with reference quantum dynamics. The details of wave packet evolutions are discussed for the case of the two-dimensional model. The fixed basis is found to be superior to the moving one in reproducing true nonlocal spreading and maintaining correct shape of the wave packet upon time evolution. Moreover, for the models considered, the fixed basis set outperforms the moving one in terms of computational efficiency.}, language = {en} } @article{SchleierGerlachPratimMukhopadhyayetal.2022, author = {Schleier, Domenik and Gerlach, Marius and Pratim Mukhopadhyay, Deb and Karaev, Emil and Schaffner, Dorothee and Hemberger, Patrick and Fischer, Ingo}, title = {Ammonia Borane, NH\(_{3}\)BH\(_{3}\): A Threshold Photoelectron-Photoion Coincidence Study of a Potential Hydrogen-Storage Material}, series = {Chemistry-A European Journal}, volume = {28}, journal = {Chemistry-A European Journal}, number = {42}, doi = {10.1002/chem.202201378}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:20-opus-318895}, year = {2022}, abstract = {We have investigated the photoionization of ammonia borane (AB) and determined adiabatic ionization energy to be 9.26±0.03 eV for the X\(^{+}\) \(^{2}\)E←X \(^{1}\)A\(_{1}\) transition. Although the threshold photoelectron spectrum appears at first glance to be similar to the one of the isosteric ethane, the electronic situation differs markedly, due to different orbital energies. In addition, an appearance energy AE\(_{0K}\)-(NH\(_{3}\)BH\(_{3}\), NH\(_{3}\)BH\(_{2}\)\(^{+}\))= 10.00±0.03 eV has been determined, corresponding to the loss of a hydrogen atom at the BH\(_{3}\)-site. From the data, a 0 K bond dissociation energy for the B-H bond in the cation of 71.5±3 kJ mol\(^{-1}\) was derived, whereas the one in the neutral compound has been estimated to be 419±10 kJ mol\(^{-1}\).}, language = {en} }