TY - THES A1 - Balagurin, Oleksii T1 - Designoptimierung von Sternsensoren für Pico- und Nanosatelliten T1 - Design optimization of star sensors for pico- and nanosatellites N2 - Die Raumfahrt ist eine der konservativsten Industriebranchen. Neue Entwicklungen von Komponenten und Systemen beruhen auf existierenden Standards und eigene Erfahrungen der Entwickler. Die Systeme sollen in einem vorgegebenen engen Zeitrahmen projektiert, in sehr kleiner Stückzahl gefertigt und schließlich aufwendig qualifiziert werden. Erfahrungsgemäß reicht die Zeit für Entwicklungsiterationen und weitgehende Perfektionierung des Systems oft nicht aus. Fertige Sensoren, Subsysteme und Systeme sind Unikate, die nur für eine bestimme Funktion und in manchen Fällen sogar nur für bestimmte Missionen konzipiert sind. Eine Neuentwicklung solcher Komponenten ist extrem teuer und risikobehaftet. Deswegen werden flugerprobte Systeme ohne Änderungen und Optimierung mehrere Jahre eingesetzt, ohne Technologiefortschritte zu berücksichtigen. Aufgrund des enormen finanziellen Aufwandes und der Trägheit ist die konventionelle Vorgehensweise in der Entwicklung nicht direkt auf Kleinsatelliten übertragbar. Eine dynamische Entwicklung im Low Cost Bereich benötigt eine universale und für unterschiedliche Anwendungsbereiche leicht modifizierbare Strategie. Diese Strategie soll nicht nur flexibel sein, sondern auch zu einer möglichst optimalen und effizienten Hardwarelösung führen. Diese Arbeit stellt ein Software-Tool für eine zeit- und kosteneffiziente Entwicklung von Sternsensoren für Kleinsatelliten vor. Um eine maximale Leistung des Komplettsystems zu erreichen, soll der Sensor die Anforderungen und Randbedingungen vorgegebener Anwendungen erfüllen und darüber hinaus für diese Anwendungen optimiert sein. Wegen der komplexen Zusammenhänge zwischen den Parametern optischer Sensorsysteme ist keine „straightforward" Lösung des Problems möglich. Nur durch den Einsatz computerbasierter Optimierungsverfahren kann schnell und effizient ein bestmögliches Systemkonzept für die gegebenen Randbedingungen ausgearbeitet werden. N2 - Aerospace is one of the most conservative industries. New developments of components and systems are based on existing standards and experience of developers. The systems should be projected in a given tight time frame, manufactured in very small quantities and finally qualified in a costly way. Experience shows that there is often insufficient time for development iterations and extensive perfection of the system. Finished sensors, subsystems and systems are unique, designed only for a specific function and in some cases even only for specific missions. New development of such components is extremely expensive and risky. For this reason, flight-proven systems are used for several years without modifications or optimization, and without taking technological advances into account. Due to the enormous financial effort and lethargy, the common approach to development is not directly applicable to small satellites. Dynamic development in the low-cost sector requires a universal strategy that can be easily modified for different applications. This strategy should not only be flexible, but also lead to the most optimal and efficient hardware solution. This work presents a software tool for a time and cost efficient development of star sensors for small satellites. In order to achieve maximal performance of the complete system, the sensor should fulfil the requirements and constraints of specified applications and, moreover, be optimized for these applications. Due to the complex interrelationships between the parameters of optical sensor systems, no straight forward solution of the problem is possible. Only by using computer based optimization methods, a best possible system concept for the given boundary conditions can be worked out quickly and efficiently. T3 - Raumfahrttechnik und Extraterrestrik - 1 KW - Sternsensor KW - CubeSat KW - Satellit KW - Optimisation KW - Star sensor KW - Star tracker Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-258966 ER - TY - JOUR A1 - Grzesik, Benjamin A1 - Baumann, Tom A1 - Walter, Thomas A1 - Flederer, Frank A1 - Sittner, Felix A1 - Dilger, Erik A1 - Gläsner, Simon A1 - Kirchler, Jan-Luca A1 - Tedsen, Marvyn A1 - Montenegro, Sergio A1 - Stoll, Enrico T1 - InnoCube — a wireless satellite platform to demonstrate innovative technologies JF - Aerospace N2 - A new innovative satellite mission, the Innovative CubeSat for Education (InnoCube), is addressed. The goal of the mission is to demonstrate “the wireless satellite”, which replaces the data harness by robust, high-speed, real-time, very short-range radio communications using the SKITH (SKIpTheHarness) technology. This will make InnoCube the first wireless satellite in history. Another technology demonstration is an experimental energy-storing satellite structure that was developed in the previous Wall#E project and might replace conventional battery technology in the future. As a further payload, the hardware for the concept of a software-based solution for receiving signals from Global Navigation Satellite Systems (GNSS) will be developed to enable precise position determination of the CubeSat. Aside from technical goals this work aims to be of use in the teaching of engineering skills and practical sustainable education of students, important technical and scientific publications, and the increase of university skills. This article gives an overview of the overall design of the InnoCube. KW - CubeSat KW - wireless-bus KW - harness free satellite KW - satellite technology KW - CubeSat GNSS KW - laser ranging KW - structural battery KW - dependable software KW - Rodos Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-239564 SN - 2226-4310 VL - 8 IS - 5 ER - TY - THES A1 - Kramer, Alexander T1 - Orbit control of a very small satellite using electric propulsion T1 - Orbitregelung eines Kleinstsatelliten mithilfe eines elektrischen Antriebssystems N2 - Miniaturized satellites on a nanosatellite scale below 10kg of total mass contribute most to the number of launched satellites into Low Earth Orbit today. This results from the potential to design, integrate and launch these space missions within months at very low costs. In the past decade, the reliability in the fields of system design, communication, and attitude control have matured to allow for competitive applications in Earth observation, communication services, and science missions. The capability of orbit control is an important next step in this development, enabling operators to adjust orbits according to current mission needs and small satellite formation flight, which promotes new measurements in various fields of space science. Moreover, this ability makes missions with altitudes above the ISS comply with planned regulations regarding collision avoidance maneuvering. This dissertation presents the successful implementation of orbit control capabilities on the pico-satellite class for the first time. This pioneering achievement is demonstrated on the 1U CubeSat UWE–4. A focus is on the integration and operation of an electric propulsion system on miniaturized satellites. Besides limitations in size, mass, and power of a pico-satellite, the choice of a suitable electric propulsion system was driven by electromagnetic cleanliness and the use as a combined attitude and orbit control system. Moreover, the integration of the propulsion system leaves the valuable space at the outer faces of the CubeSat structure unoccupied for future use by payloads. The used NanoFEEP propulsion system consists of four thruster heads, two neutralizers and two Power Processing Units (PPUs). The thrusters can be used continuously for 50 minutes per orbit after the liquefaction of the propellant by dedicated heaters. The power consumption of a PPU with one activated thruster, its heater and a neutralizer at emitter current levels of 30-60μA or thrust levels of 2.6-5.5μN, respectively, is in the range of 430-1050mW. Two thruster heads were activated within the scope of in-orbit experiments. The thrust direction was determined using a novel algorithm within 15.7° and 13.2° of the mounting direction. Despite limited controllability of the remaining thrusters, thrust vector pointing was achieved using the magnetic actuators of the Attitude and Orbit Control System. In mid 2020, several orbit control maneuvers changed the altitude of UWE–4, a first for pico-satellites. During the orbit lowering scenario with a duration of ten days, a single thruster head was activated in 78 orbits for 5:40 minutes per orbit. This resulted in a reduction of the orbit altitude by about 98.3m and applied a Delta v of 5.4cm/s to UWE–4. The same thruster was activated in another experiment during 44 orbits within five days for an average duration of 7:00 minutes per orbit. The altitude of UWE–4 was increased by about 81.2m and a Delta v of 4.4cm/s was applied. Additionally, a collision avoidance maneuver was executed in July 2020, which increased the distance of closest approach to the object by more than 5000m. N2 - Heutzutage werden überwiegend Kleinstsatelliten in niedrige Erdumlaufbahnen befördert, da dies schnell und sehr kostengünstig möglich ist. Von der Planung bis zum Raketenstart vergehen oft nur wenige Monate. Im vergangenen Jahrzehnt haben sich Kleinstsatelliten bezüglich Systemgestaltung, Kommunikation und Lageregelung dahingehend weiterentwickelt, dass diese in den Anwendungsbereichen Erdbeobachtung, Kommunikationsdienstleistungen und wissenschaftlichen Missionen mit herkömmlichen Satelliten konkurrieren können. Ein weiterer wichtiger Entwicklungsschritt für Kleinstsatelliten wäre die Möglichkeit der Orbitkontrolle. Diese würde die Betreiber befähigen, die Flugbahn der Satelliten entsprechend den aktuellen Zielen der Mission anzupassen und Formationsflug von Kleinstsatelliten durchzuführen, um neue wissenschaftliche Erkenntnisse in vielen Bereichen der Weltraumforschung zu fördern. Gleichzeitig würden Kleinstsatelliten den aktuell geplanten Vorschriften Rechnung tragen, nach denen Satelliten mit Flughöhen oberhalb der ISS manövrierfähig sein müssen, um Kollisionen zu vermeiden. Die vorliegende Dissertation präsentiert die erste erfolgreiche Orbitkontrolle auf einem Piko-Satelliten. Diese Pionierleistung wird auf dem 1U CubeSat UWE–4 demonstriert. Ein Schwerpunkt dieser Arbeit liegt dabei auf der Integration und dem Betrieb eines elektrischen Antriebssystems auf Kleinstsatelliten. Diese Integration des Antriebssystems hält den wertvollen Platz an den Außenflächen des CubeSats für zukünftige Nutzlasten frei und ermöglicht dessen Anwendung als Lage- und Orbitregelungsaktuator. Das verwendete NanoFEEP Antriebssystem beinhaltet vier Triebwerke, zwei Neutralisatoren und zwei Platinen zur Steuerung. Nach der Verflüssigung des Treibstoffs durch dedizierte Heizer können die Triebwerke pro Erdumrundung für 50 Minuten kontinuierlich genutzt werden. Der Stromverbrauch einer Steuerplatine mit einem aktiven Triebwerk, seinem Heizer und einem Neutralisator bei Emitterströmen von 30-60μA bzw. Schüben von 2.6-5.5μN liegt im Bereich von 430-1050mW. Im Rahmen von In- Orbit Experimenten wurden zwei Triebwerke aktiviert. Die Schubrichtungen der aktiven Triebwerke konnten mit einem neuartigen Algorithmus in einem Winkel von 15.7° bzw. 13.2° bezüglich ihrer Einbaurichtung bestimmt werden. Trotz mangelnder Steuerbarkeit der verbleibenden Triebwerke konnte eine Ausrichtung des Schubvektors unter Zuhilfenahme der magnetischen Aktuatoren des Lageregelungssystems erreicht werden. Mehrere Orbitregelungsexperimente zur Veränderung der Flughöhe konnten Mitte 2020 zum ersten Mal auf einem Piko-Satelliten gezeigt werden. Um die Flughöhe zu verringern, wurde ein Triebwerk über einen Zeitraum von zehn Tagen während 78 Orbits gefeuert, wobei dieses pro Erdumrundung für durchschnittlich 5:40 Minuten aktiviert wurde. Hierdurch wurde die Flughöhe von UWE–4 um 98m reduziert und seine Geschwindigkeit um ein Delta v von 7.2cm/s erhöht. In einem anderen Experiment wurde dasselbe Triebwerk während 44 Orbits in einem Zeitraum von fünf Tagen für durchschnittlich 7:00 Minuten aktiviert, wodurch die Flughöhe des Kleinstsatelliten um 74.2m angehoben und seine Geschwindigkeit um ein Delta v von 4.0cm/s verringert wurde. Zudem wurde ein Manöver zur Kollisionsvermeidung durchgeführt, das den Abstand zwischen UWE–4 und dem Objekt auf Kollisionskurs zum Zeitpunkt der kleinsten Annäherung um mehr als 5000m vergrößert hat. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 22 KW - Kleinsatellit KW - Plasmaantrieb KW - Flugbahn KW - Flughöhe KW - Kollisionsschutz KW - CubeSat Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-241552 SN - 978-3-945459-34-8 (online) ER - TY - JOUR A1 - Kramer, Alexander A1 - Bangert, Philip A1 - Schilling, Klaus T1 - UWE-4: First Electric Propulsion on a 1U CubeSat — In-Orbit Experiments and Characterization JF - Aerospace N2 - The electric propulsion system NanoFEEP was integrated and tested in orbit on the UWE-4 satellite, which marks the first successful demonstration of an electric propulsion system on board a 1U CubeSat. In-orbit characterization measurements of the heating process of the propellant and the power consumption of the propulsion system at different thrust levels are presented. Furthermore, an analysis of the thrust vector direction based on its effect on the attitude of the spacecraft is described. The employed heater liquefies the propellant for a duration of 30 min per orbit and consumes 103 ± 4 mW. During this time, the respective thruster can be activated. The propulsion system including one thruster head, its corresponding heater, the neutralizer and the digital components of the power processing unit consume 8.5 ± 0.1 mW ⋅μ A\(^{−1}\) + 184 ± 8.5 mW and scales with the emitter current. The estimated thrust directions of two thruster heads are at angles of 15.7 ± 7.6∘ and 13.2 ± 5.5∘ relative to their mounting direction in the CubeSat structure. In light of the very limited power on a 1U CubeSat, the NanoFEEP propulsion system renders a very viable option. The heater of subsequent NanoFEEP thrusters was already improved, such that the system can be activated during the whole orbit period. KW - CubeSat KW - UWE-4 KW - electric propulsion KW - NanoFEEP KW - power consumption KW - thrust direction KW - characterization KW - in-orbit experiments Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-236124 VL - 7 IS - 7 ER - TY - RPRT A1 - Riegler, Clemens A1 - Kayal, Hakan T1 - VELEX: Venus Lightning Experiment N2 - Lightning has fascinated humanity since the beginning of our existence. Different types of lightning like sprites and blue jets were discovered, and many more are theorized. However, it is very likely that these phenomena are not exclusive to our home planet. Venus’s dense and active atmosphere is a place where lightning is to be expected. Missions like Venera, Pioneer, and Galileo have carried instruments to measure electromagnetic activity. These measurements have indeed delivered results. However, these results are not clear. They could be explained by other effects like cosmic rays, plasma noise, or spacecraft noise. Furthermore, these lightning seem different from those we know from our home planet. In order to tackle these issues, a different approach to measurement is proposed. When multiple devices in different spacecraft or locations can measure the same atmospheric discharge, most other explanations become increasingly less likely. Thus, the suggested instrument and method of VELEX incorporates multiple spacecraft. With this approach, the question about the existence of lightning on Venus could be settled. T3 - Raumfahrttechnik und Extraterrestrik - 3 KW - Venus KW - Lightning KW - CubeSat KW - Balloon KW - Autorotation Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-282481 ER -