TY - THES A1 - Rieger, Max T1 - Preconcentration with Metal-Organic Frameworks as adsorbents for airborne Explosives and Hazardous Materials - A study using inverse gas chromatography T1 - Anreicherung mit Metal-Organic Frameworks als „Adsorbentien für luftgetragene Explosiv- und Gefahrstoffe - Eine Studie mit inverser Gaschromatographie" N2 - Sensitivity and selectivity remain the central technical requirement for analytical devices, detectors and sensors. Especially in the gas phase, concentrations of threat substances can be very low (e.g. explosives) or have severe effects on health even at low concentrations (e.g. benzene) while it contains many potential interferents. Preconcentration, facilitated by active or passive sampling of air by an adsorbent, followed by thermal desorption, results in these substances being released in a smaller volume, effectively increasing their concentration. Traditionally, a wide range of adsorbents, such as active carbons or porous polymers, are used for preconcentration. However, many adsorbents either show chemical reactions due to active surfaces, serious water retention or high background emission due to thermal instability. Metal-organic frameworks (MOFs) are a hybrid substance class, composed inorganic and organic building blocks, being a special case of coordination polymers containing pores. They can be tailored for specific applications such as gas storage, separation, catalysis, sensors or drug delivery. This thesis is focused on investigating MOFs for their use in thermal preconcentration for airborne detection systems. A pre-screening method for MOF-adsorbate interactions was developed and applied, namely inverse gas chromatography (iGC). Using this pulse chromatographic method, the interaction of MOFs and molecules from the class of explosives and volatile organic compounds was studied at different temperatures and compared to thermal desorption results. In the first part, it is shown that archetype MOFs (HKUST-1, MIL-53 and Fe-BTC) outperformed the state-of-the-art polymeric adsorbent Tenax® TA in nitromethane preconcentration for a 1000 (later 1) ppm nitromethane source. For HKUST-1, a factor of more than 2000 per g of adsorbent was achieved, about 100 times higher than for Tenax. Thereby, a nitromethane concentration of 1 ppb could be increased to 2 ppm. High enrichment is addressed to the specific interaction of the nitro group as by iGC, which was determined by comparing nitromethane’s free enthalpy of adsorption with the respective saturated alkane. Also, HKUST-1 shows a similar mode of sorption (enthalpy-entropy compensation) for nitro and saturated alkanes. In the second part, benzene of 1 ppm of concentration was enriched with a similar setup, using 2nd generation MOFs, primarily UiO-66 and UiO-67, under dry and humid (50 %rH) conditions using constant sampling times. Not any MOF within the study did surpass the polymeric Tenax in benzene preconcentration. This is most certainly due to low sampling times – while Tenax may be highly saturated after 600 s, MOFs are not. For regular UiO-66, four differently synthesized samples showed a strongly varying behavior for dry and humid enrichment which cannot be completely explained. iGC investigations with regular alkanes and BTEX compounds revealed that confinement factors and dispersive surface energy were different for all UiO-66 samples. Using physicochemical parameters from iGC, no unified hypothesis explaining all variances could be developed. Altogether, it was shown that MOFs can replace or add to state-of-the-art adsorbents for the enrichment of specific analytes with preconcentration being a universal sensitivity-boosting concept for detectors and sensors. Especially with iGC as a powerful screening tool, most suitable MOFs for the respective target analyte can be evaluated. iGC can be used for determining “single point” retention volumes, which translate into partition coefficients for a specific MOF × analyte × temperature combination. N2 - Empfindlichkeit und Selektivität bleiben die zentralen technischen Anforderungen an analytische Geräte, Detektoren und Sensoren. Speziell in der Gasphase können die Konzentrationen von Gefahrstoffen sehr niedrig sein (z. B. Explosivstoffe) oder bereits bei niedrigen Konzentrationen schädigende Auswirkungen auf die Gesundheit aufweisen (z. B. Benzol) während sie viele potenzielle Interferenzien enthält. Präkonzentration, die durch aktives oder passives Sampling von Luft durch ein Adsorbens, gefolgt von einer Thermodesorption realisiert wird, setzt diese Substanzen effektiv in einem kleineren Volumen frei, was zu einer Erhöhung der Konzentration führt. Üblicherweise wird hierfür eine breite Auswahl an Adsorbentien wie Aktivkohlen oder poröse Polymere verwendet. Jedoch weisen viele Adsorbentien entweder chemische Reaktionen wegen aktiver Oberflächen, starke Wasserretention oder hohe Hintergrundemission wegen thermischer Instabilität auf. Metal-organic frameworks (MOFs) sind eine hybride Substanzklasse, ein Spezialfall der porösen Koordinationspolymere, die aus anorganischen und organischen Baugruppen aufgebaut sind. Sie können für spezifische Anwendungen wie Gasspeicherung, Trennung, Katalyse, Sensorik oder Wirkstofftransport maßgeschneidert werden. Diese Arbeit befasst sich hauptsächlich mit der Untersuchung von MOFs bei der thermischen Anreicherung für luftgetragene Detektionssysteme. Eine Methode zur schnellen Untersuchung von MOF-Analyt Interaktionen wurde entwickelt und angewendet, die inverse Gaschromatographie (iGC). Mit dieser pulschromatographischen Methode wurde die Interaktion von MOFs und Molekülen aus der Klasse der Explosivstoffe sowie Klasse der flüchtigen organischen Verbindungen (VOCs) in der Gasphase bei verschiedenen Temperaturen untersucht und mit Thermodesorptionsmessungen verglichen. Im ersten Teil der Arbeit würde gezeigt das Modell-MOFs (HKUST-1, MIL-53 und Fe-BTC) den polymeren Standard Tenax® TA beim Anreichern von Nitromethan an einer 1000 (später 1) ppm Nitromethan Quelle übertrafen. Im Fall von HKUST-1 konnte ein Faktor von 2000 pro Gramm erreicht werden, etwa 100-fach höher als für Tenax. Auf diese Weise könnte eine Nitromethan Konzentration von 1 ppb auf 2 ppm erhöht werden. Diese hohen Anreicherungsfaktoren entstammen vermutlich der hohen spezifischen Wechselwirkung der Nitrogruppe mit den MOFs. Diese wurden durch iGC beim Vergleich von Nitromethans freier Adsorptionsenthalpie mit dem entsprechenden gesättigten Alkan ermittelt. HKUST-1 weist auch einen ähnlichen Adsorptionsmodus (Enthalpie-Entropie Kompensation) für Nitro- und gesättigte Alkane auf. Im zweiten Teil der Arbeit wurde die Anreicherung von 1 ppm Benzol, mit einem ähnlichen Aufbau und anderen MOFs, hauptsächlich UiO-66 und UiO-67, unter trockenen und feuchten (50 %rF) Bedingungen bei konstanten Samplingzeiten, untersucht. Hierbei konnte kein MOF das polymere Tenax beim Anreichern von Benzol übertreffen. Dies liegt vermutlich an den niedrigen Samplingzeiten – während Tenax nach 600 s bereits stark gesättigt ist, gilt dies nicht für MOFs. Im Fall von UiO-66 zeigten vier Proben unterschiedlicher Herkunft ein stark unterschiedliches Verhalten bei trockener und feuchter Anreicherung welches nicht vollständig erklärt werden kann. iGC Untersuchungen mit gesättigten Alkanen und BTEX-Verbindungen konnten aufzeigen, dass räumliche Beschränktheitsfaktoren und dispersive Oberflächenenergien für alle vier Proben unterschiedlich waren. Mit physikochemischen Parametern aus iGC-Messungen konnte jedoch keine einheitliche Hypothese zum Unterscheiden der Proben entwickelt werden. Insgesamt konnte gezeigt werden, dass MOFs bestehende Adsorbens-Standards zum Anreichern von bestimmten Analyten ersetzen oder erweitern können, wobei Präkonzentration ein Konzept ist, welches universell die Empfindlichkeit eines Detektors oder Sensors steigern kann. Insbesondere mit iGC als mächtiges Werkzeug zur Vorselektion können passende MOFs für die entsprechenden Zielanalyten evaluiert werden. Ebenso kann iGC auch zur Bestimmung von Einzelpunkt Retentionsvolumen, welche Verteilungskoeffizienten für eine bestimmte MOF × Analyt × Temperatur Kombination entsprechen, genutzt werden. KW - Metallorganisches Netzwerk KW - MOF KW - Gas chromatography KW - iGC KW - Explosives KW - Preconcentration KW - Explosivstoff KW - Inverse Gaschromatographie Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-177750 ER - TY - THES A1 - Jaud, Tobias Armin T1 - Application based personalized food choices and health sustainment: scientific background and investigation of biomarkers in human tissue specimens T1 - Gesundheitserhaltende Ernährung: Wissenschaftlicher Hintergrund einer App zur personalisierten Lebensmittelauswahl und Identifizierung von Biomarkern für die Ernährungsweise in Humangewebe N2 - Dietary fatty acids serve as objective biomarkers for the estimation of habitual diet mainly because biomarkers are free of memory bias or inaccuracies of food databases. The aim of the present work encompassed the implementation of a gas chromatographical method coupled with a mass spectrometrical and flame-ionization detector for analysis of fatty acid biomarkers in human biospecimens, their analytical determination and statistical evaluation in two different study populations and different biospecimens as well as the elaboration of adverse reactions to food ingredients with special focus on food allergies and food intolerances in the context of a possible implementation into an application for consumer health. The first aim was the identification of potential influence of fatty acid biomarkers on desaturase and elongase indexes (Δ9DI, Δ6DI, Δ5DI and ELOVLI5), which are factors in type 2 diabetes risk, in breast adipose tissue from healthy women. Influence of further variables on respective indexes was also investigated. 40 samples were investigated and potential variables were either collected by questionnaire or determined. Principle component analysis was applied for fatty acid biomarkers (PCdiet1, PCdiet2 and PCdiet3 representative for the dietary intake of vegetable oils/nuts, fish and partially hydrogenated vegetable oils), endogenous estrogens (PCE1) and oxysterols (PCOxy1). Multiple linear regression models were applied. Δ9DI and Δ6DI were influenced non-significantly and significantly negatively by PCdiet2 supporting a putative beneficial effect of vegetable oils and nuts on type 2 diabetes risk factors. ELOVLI5 and Δ5DI were influenced significantly and non-significantly positively by PCdiet1 supporting a putative beneficial effect of fish consumption on type 2 diabetes risk factors. On the other hand, PCdiet1 also significantly and non-significantly positively influenced Δ9DI and Δ6DI supporting a putative adverse effect of fish biomarkers on type 2 diabetes risk factors. The opposing influences of PCdiet1 suggesting an ambivalent role of dietary intake of fish on investigated indexes. Δ6DI was significantly positively influenced by PCdiet3 and number of pregnancies supporting a putative adverse effect of partially hydrogenated vegetable oils and pregnancies on type 2 diabetes risk factors. Lifestyle factors like smoking significantly and non-significantly influenced Δ9DI and Δ6DI putatively adversely. Δ5DI was influenced significantly positively by estrogen active drugs suggesting a putative beneficial effect on type 2 diabetes risk factors. It must be considered that a variation coefficient of up to 0.44 only explained 44% of variance of the respective indexes, suggesting other influencing factors might play a role. The second aim was the implementation of a gas chromatographical method coupled with a mass spectrometrical and flame-ionization detector for analysis of fatty acid biomarkers in human biospecimens. The method was optimized for separation and detection of 40 fatty acids. Mean recovery for tridecanoic acid was x(tridecanoic acid) = 90.51% and for nonadecanoic acid x(nonadecanoic acid) = 96.21%. Thus, there was no significant loss of fatty acids with shorter and longer carbon chains over the extraction process to be expected. Limit of detections were calculated in adipose tissue samples and ranged from 0.007 to 0.077% of the proportion of the respective fatty acid to total fatty acids. The third aim was the investigation if differentiation between breast glandular and adipose tissue had a relevant impact on the analysis of dietary fatty acid biomarkers or if contamination of breast glandular with breast adipose tissue and vice versa was neglectable for the analysis of dietary fatty acid biomarkers. No statistical significant differences were observed for all investigated fatty acid biomarkers (pentadecanoic-, heptadecanoic-, trans palmitoleic-, eicosapentaenoic-, docosahexaenoic-, linoleic and α-linolenic acid) between breast glandular and adipose tissue. Thus, differentiation between breast glandular and adipose tissue seems not to be necessary for the analysis of fatty acids serving as biomarkers for the intake of specific food groups. Potential influence of mixed breast tissue on fatty acid biomarkers analysis seems to be neglectable. The fourth aim was the determination of fatty acid biomarkers in adipose tissue in another study population from healthy participants. 27 adipose tissue samples were analyzed. Milk and ruminant fat biomarkers exhibited proportions of 0.47% for pentadecanoic acid, 0.34% for heptadecanoic acid and 0.25% for trans palmitoleic acid. Fish fatty acid biomarkers revealed proportions of 0.034% for eicosapentaenoic acid and 0.061% for docosahexaenoic acid. The mean proportion of vegetable oils and nuts biomarkers were 9.58% for linoleic acid and 0.48% for α-linolenic acid in all adipose tissues. Principle component analysis was applied for the fatty acid biomarkers to provide objective markers of habitual diet for this study population. PCdiet1 was mainly characterized by pentadecanoic acid, heptadecanoic acid and trans palmitoleic acid and therefore served as a principle component for the dietary intake of milk and ruminant fat. PCdiet2 and PCdiet3 only exhibited pattern for ω3 and ω6 fatty acids but not for dietary intake of specific food groups and could therefore not used as objective marker. PCdiet1, 2 and 3 explained 82.76% of variance. The last aim of this thesis was the elaboration of adverse reactions to food ingredients with special focus on food allergies and food intolerances in the context of a possible implementation into an application for consumer health. Scientific information on adverse reactions to food ingredients and trigger substances was provided in this thesis and possible implementation strategies were evaluated. For food allergens, which have regulatory requirements in the context of labelling, a strategy was elaborated, where it is necessary to provide information on the list of ingredients, the nexus ’contain’ and the respective food allergen as well as information on the name of the product. For food intolerances, which do not have regulatory requirements, limits were shown in the context of the application. If the elaborated food intolerances shall be implemented into the application, a professional dietary concept has to be developed for every food intolerance because of the complexity of the implementation. N2 - Die vorliegende Arbeit umfasste die Implementierung einer analytischen Methode zur Bestimmung von Fettsäurebiomarkern in unterschiedlichen Bioproben, die analytische Bestimmung und statistische Evaluation von Fettsäurebiomarkern in zwei Studienpopulationen und unterschiedlichen Bioproben sowie die Ausarbeitung und Bereitstellung wissenschaftlicher Information zu adversen Reaktionen von Lebensmittelzutaten mit besonderem Fokus auf Nahrungsmittelallergien sowie Nahrungsmittelunverträglichkeiten im Kontext einer strategischen Implementierung dieser adversen Reaktionen in eine Applikation im Sinne des Verbraucherschutzes. Das erste Ziel war die Identifizierung von potentiellen Einflüssen durch Fettsäurebiomarker der Ernährung auf Desaturase- und Elongase-Indices (Δ9DI, Δ6DI, Δ5DI, ELOVLI5), welche Einflussfaktoren auf das Typ 2 Diabetes Risiko darstellen, in Brustfettgewebe von gesunden Frauen. Der potentielle Einfluss von weiteren Variablen auf Desaturase- und Elongase-Indices wurde ebenfalls untersucht. 40 Proben wurden untersucht und potentielle Variablen sowohl mithilfe eines Fragebogens erhoben als auch analytisch ermittelt. Hauptkomponentenanalysen wurden für Fettsäurebiomarker (PCdiet1, PCdiet2 und PCdiet3 repräsentativ für eine Ernährung reich an pflanzlichen Ölen/Nüssen, Fisch und gehärteten Ölen), endogene Estrogene (PCE1) und Oxysterole (PCOxy1) angewendet. Potentielle Einflussfaktoren wurden mittels multiple linearer Regressionsanalyse ermittelt. Δ9DI und Δ6DI wurden nicht-signifikant und signifikant durch PCdiet2 beeinflusst. Dies unterstützt einen möglicherweise vorteilhaften Effekt von Fettsäurebiomarkern repräsentativ für die Aufnahme von pflanzlichen Ölen und Nüssen auf Typ 2 Diabetes Risikofaktoren. PCdiet1 hatte einen möglicherweise vorteilhaften signifikanten und nicht-signifikanten Einfluss auf ELOVLI5 und Δ5DI. Auf der anderen Seite hatte PCdiet1 einen möglicherweise adversen signifikanten Einfluss auf Δ9DI und Δ6DI, was auf eine ambivalente Rolle von Fettsäurebiomarkern des Fischkonsums hindeutet. Möglicherweise adverse signifikante Einflüsse auf Δ6DI hatten PCdiet3 sowie die Anzahl an Schwangerschaften. Rauchen hatte einen signifikanten und nicht-signifikanten möglicherweise adversen Einfluss auf Δ9DI und Δ6DI. Einen möglicherweise vorteilhaften Einfluss auf ELOVLI5 wurde mit der Einnahme von estrogenaktiven Substanzen beobachtet. Berücksichtigt werden muss allerdings, dass mit einem Variationskoeffizienten von bis zu 0.44 nur 44% der Varianz der entsprechenden Indices erklärt werden konnte und somit weitere Einflussfaktoren eine Rolle spielen könnten. Das zweite Ziel war die Implementierung einer gaschromatographischen Methode für die Trennung und Detektion von 40 Fettsäuren. Die Chromatographie war simultan an einen Massenspektrometer und einen Flammenionisationsdetektor gekoppelt. Recovery Versuche zeigten für die Internen Standards Tridecansäure und Nonadecansäure Wiederfindungs raten von x(Tridecansäure) = 90.51% und x(Nonadecansäure) = 96.21%. Die Nachweisgrenzen der Fettsäuren wurden mit Fettgewebsproben bestimmt und reichten von 0.007 bis 0.077% Anteil der jeweiligen Fettsäuren an der Gesamtfettsäureverteilung. Die Untersuchung der Fragestellung ob die Differenzierung zwischen Brustdrüsen- und Brustfettgewebe einen relevanten Einfluss auf die Analyse von Fettsäurebiomarkern repräsentativ für eine Ernährung reich an Milch, Fisch und pflanzlichen Ölen/Nüssen hat war das dritte Ziel der vorliegenden Arbeit. Es wurde kein statistisch signifikanter Unterschied zwischen den prozentualen Anteilen der Fettsäurebiomarkern (Pentadecan-, Heptadecan-, trans Palmitolein-, Eicosapentaen-, Docosahexaen-, Linol- und α-Linolensäure) in Brustdrüsen und Brustfettgewebe entdeckt. Eine Differenzierung zwischen Brustdrüsen- und Brustfettgewebe scheint daher in Bezug auf die Analyse von Fettsäurebiomarker der Ernährung nicht notwendig zu sein. Der potentielle Einfluss von, mit Brustdrüsen- und Brustfettgewebe, gemischtem Gewebe scheint damit in Bezug auf die Analyse von Fettsäurebiomarkern vernachlässigbar zu sein. Das vierte Ziel der vorliegenden Arbeit war die Bestimmung der Fettsäureverteilung mit besonderem Fokus auf Fettsäurebiomarker für die Ernährung in Fettgewebe in einer anderen Studienpopulation von gesunden Teilnehmerinnen und Teilnehmern. 27 Fettgewebsproben wurde untersucht. Der Anteil an Fettsäurebiomarker für den Konsum von Milch- und Wiederkäuerfette betrug 0.47% für Pentadecansäure, 0.34% für Heptadecansäure und 0.25% für trans Palmitoleinsäure. Fettsäurebiomarker repräsentativ für Fischkonsum hatten Anteile von 0.034% für Eicosapentaensäure und 0.061% für Docosahexaensäure. Für Fettsäurebiomarker repräsentativ für den Konsum von pflanzlichen Fetten und Nüssen wurden Anteile von 9.58% für Linolsäure und 0.48% für α-Linolensäure gefunden. Anschließend wurde eine Hauptkomponentenanalyse der Fettsäurebiomarker für die Ernährung durchgeführt. PCdiet1 wurde hauptsächlich durch Pentadecansäure, Heptadecansäure und trans Palmitoleinsäure charakterisiert. PCdiet1 wurde folglich als Hauptkomponente für den Konsum von Milch- und Wiederkäuerfetten interpretiert. PCdiet2 und PCdiet3 wurden ausschließlich von ω3 und ω6 Fettsäuren charakterisiert. Eine eindeutige Zuordnung zu speziellen Lebensmittelgruppen war nicht möglich. Die Biomarker für den Konsum von Fisch und pflanzlichen Fetten sowie Nüssen können daher nicht durch PCdiet2 und PCdiet3 zusammengefasst werden. PCdiet1, 2 und 3 erklärten 82.76% der Varianz. Das letzte Ziel der vorliegenden Arbeit war die Ausarbeitung von adversen Reaktionen gegenüber Lebensmittelinhaltsstoffen mit speziellem Fokus auf Nahrungsmittelallergien und Nahrungsmittelunverträglichkeiten im Kontext einer möglichen Implementierung in eine Applikation im Sinne des Verbraucherschutzes. Hierfür wurden wissenschaftliche Informationen zu adversen Reaktionen gegenüber Lebensmittelinhaltsstoffen und potentiellen Triggersubstanzen zusammengetragen und mögliche Implementierungsstrategien evaluiert. Für Nahrungsmittelallergene, welche spezielle regulatorische Voraussetzungen im Sinne von Beschriftung und Deklaration besitzen, wurde eine Strategie ausgearbeitet, welche die Notwendigkeit der Informationen von Zutatenliste, der Verknüpfung der Signalwörter ’enthält’ und dem entsprechenden Allergen wie auch den Namen des Produktes beinhaltet. Zutaten und Inhaltsstoffe, die Nahrungsmittelunverträglichkeiten hervorrufen können, haben keine speziellen regulatorischen Voraussetzungen. Limitierungen einer möglichen Implementierung von Nahrungsmittelunverträglichkeiten in die Applikation wurden im Rahmen dieser Arbeit aufgezeigt. Aufgrund der Komplexizität der Implementierung einer jeder einzelnen Nahrungsmittelunverträglichkeit in die Applikation sollte für jede einzelne ausgewählte Unverträglichkeit ein individuelles Konzept entwickelt werden. KW - Lebensmittelchemie KW - Massenspektrometrie KW - Biomarker KW - Gaschromatographie KW - Masspectrometry KW - Biomarker KW - Gas chromatography Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-298646 ER -