TY - JOUR A1 - Vogel, Patrick A1 - Rückert, Martin Andreas A1 - Friedrich, Bernhard A1 - Tietze, Rainer A1 - Lyer, Stefan A1 - Kampf, Thomas A1 - Hennig, Thomas A1 - Dölken, Lars A1 - Alexiou, Christoph A1 - Behr, Volker Christian T1 - Critical Offset Magnetic PArticle SpectroScopy for rapid and highly sensitive medical point-of-care diagnostics JF - Nature Communications N2 - Magnetic nanoparticles (MNPs) have been adapted for many applications, e.g., bioassays for the detection of biomarkers such as antibodies, by controlled engineering of specific surface properties. Specific measurement of such binding states is of high interest but currently limited to highly sensitive techniques such as ELISA or flow cytometry, which are relatively inflexible, difficult to handle, expensive and time-consuming. Here we report a method named COMPASS (Critical-Offset-Magnetic-Particle-SpectroScopy), which is based on a critical offset magnetic field, enabling sensitive detection to minimal changes in mobility of MNP ensembles, e.g., resulting from SARS-CoV-2 antibodies binding to the S antigen on the surface of functionalized MNPs. With a sensitivity of 0.33 fmole/50 µl (≙7 pM) for SARS-CoV-2-S1 antibodies, measured with a low-cost portable COMPASS device, the proposed technique is competitive with respect to sensitivity while providing flexibility, robustness, and a measurement time of seconds per sample. In addition, initial results with blood serum demonstrate high specificity. KW - biochemical assays KW - characterization and analytical techniques KW - magnetic properties and materials KW - nanoparticles Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-300893 VL - 13 ER - TY - JOUR A1 - Karak, Suvendu A1 - Stepanenko, Vladimir A1 - Addicoat, Matthew A. A1 - Keßler, Philipp A1 - Moser, Simon A1 - Beuerle, Florian A1 - Würthner, Frank T1 - A Covalent Organic Framework for Cooperative Water Oxidation JF - Journal of the American Chemical Society N2 - The future of water-derived hydrogen as the “sustainable energy source” straightaway bets on the success of the sluggish oxygen-generating half-reaction. The endeavor to emulate the natural photosystem II for efficient water oxidation has been extended across the spectrum of organic and inorganic combinations. However, the achievement has so far been restricted to homogeneous catalysts rather than their pristine heterogeneous forms. The poor structural understanding and control over the mechanistic pathway often impede the overall development. Herein, we have synthesized a highly crystalline covalent organic framework (COF) for chemical and photochemical water oxidation. The interpenetrated structure assures the catalyst stability, as the catalyst’s performance remains unaltered after several cycles. This COF exhibits the highest ever accomplished catalytic activity for such an organometallic crystalline solid-state material where the rate of oxygen evolution is as high as ∼26,000 μmol L\(^{–1}\) s\(^{–1}\) (second-order rate constant k ≈ 1650 μmol L s\(^{–1}\) g\(^{–2}\)). The catalyst also proves its exceptional activity (k ≈ 1600 μmol L s\(^{–1}\) g\(^{–2}\)) during light-driven water oxidation under very dilute conditions. The cooperative interaction between metal centers in the crystalline network offers 20–30-fold superior activity during chemical as well as photocatalytic water oxidation as compared to its amorphous polymeric counterpart. KW - water oxidation KW - sustainable energy source KW - covalent organic framework KW - catalyst KW - crystalline KW - catalysis KW - nanoparticles Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-287591 UR - https://pubs.acs.org/doi/10.1021/jacs.2c07282 SN - 0002-7863 VL - 144 IS - 38 ER - TY - JOUR A1 - Han, Luyang A1 - Wiedwald, Ulf A1 - Biskupek, Johannes A1 - Fauth, Kai A1 - Kaiser, Ute A1 - Ziemann, Paul T1 - Nanoscaled alloy formation from self-assembled elemental Co nanoparticles on top of Pt films JF - Beilstein Journal of Nanotechnology N2 - The thermally activated formation of nanoscale CoPt alloys was investigated, after deposition of self-assembled Co nanoparticles on textured Pt(111) and epitaxial Pt(100) films on MgO(100) and SrTiO3(100) substrates, respectively. For this purpose, metallic Co nanoparticles (diameter 7 nm) were prepared with a spacing of 100 nm by deposition of precursor-loaded reverse micelles, subsequent plasma etching and reduction on flat Pt surfaces. The samples were then annealed at successively higher temperatures under a H2 atmosphere, and the resulting variations of their structure, morphology and magnetic properties were characterized. We observed pronounced differences in the diffusion and alloying of Co nanoparticles on Pt films with different orientations and microstructures. On textured Pt(111) films exhibiting grain sizes (20–30 nm) smaller than the particle spacing (100 nm), the formation of local nanoalloys at the surface is strongly suppressed and Co incorporation into the film via grain boundaries is favoured. In contrast, due to the absence of grain boundaries on high quality epitaxial Pt(100) films with micron-sized grains, local alloying at the film surface was established. Signatures of alloy formation were evident from magnetic investigations. Upon annealing to temperatures up to 380 °C, we found an increase both of the coercive field and of the Co orbital magnetic moment, indicating the formation of a CoPt phase with strongly increased magnetic anisotropy compared to pure Co. At higher temperatures, however, the Co atoms diffuse into a nearby surface region where Pt-rich compounds are formed, as shown by element-specific microscopy. KW - alloy KW - CoPt KW - HRTEM KW - nanoparticles KW - XMCD KW - Co KW - epitaxy KW - magnetometry KW - Pt Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-142869 VL - 2 ER - TY - THES A1 - Joshi, Sanjeev T1 - Preparation and characterization of CdS nanoparticles T1 - DPräparat und characktereisierung von CdS Nanopartikeln N2 - Zusammenfassung CdS-Nanoteilchen mit Größen zwischen 1.1 und 4.2 nm wurden in Äthanol und mit Thioglycerol (TG)-Hülle synthetisiert. Es wurde gezeigt, dass die nass-chemische Synthese ohne Wasser und die Verwendung von TG als Hülle folgende Vorteile bieten: Es konnten kleinere Teilchen hergestellt und eine schmalere Größenverteilung erzielt werden. Zusätzlich wird dem Altern der Teilchen vorgebeugt, und die Ergebnisse sind besser reproduzierbar. Hochaufgelöste Photoemissions-Messungen an kleinen CdS-Teilchen (1.1, 1.4, 1.7, 1.8; 1.8 nm mit Glutathion-Hülle) ergaben Beiträge von fünf verschiedenen Schwefelatom-Typen zum S 2p-Gesamt Signal. Außerdem wurde beobachtet, dass Nanoteilchen unterschiedlicher Größe und/oder mit unterschiedlichen Hüllen-Substanzen verschiedene Photoemissionsspektren zeigen und verschieden starke Strahlenschäden aufweisen. Bei den 1.4 nm großen CdS-Teilchen entsprechen die Komponenten des S 2p-Signals entweder Schwefelatomen mit unterschiedlichen Cd-Nachbarn, Thiol-Schwefelatomen oder teilweise oxidiertem Schwefel. Die jeweilige Zuweisung der Schwefeltypen erfolgte über Intensitäts-Änderungen der einzelnen S 2p-Komponenten als Funktion der Photonenenergie und des Strahlenschadens. Die Daten der 1.4 nm großen CdS-Teilchen wurden mit PES-Intensitäts-Rechnungen verglichen, die auf einem neuen Strukturmodell-Ansatz basieren. Von den drei verwendeten CdS-Strukturmodellen konnte nur ein Modell mit 33 S-Atomen die Variation der experimentellen Intensitäten richtig wieder geben. Modelle von größeren Nanoteilchen mit beispielsweise 53 S-Atomen zeigen Abweichungen von den experimentellen Daten der 1.4 nm-Teilchen. Auf diese Weise kann indirekt auf die Größe der gemessenen Teilchen geschlossen werden. Die Intensitätsrechnungen wurden zum einen „per Hand“ zur groben Abschätzung durchgeführt, zum anderen wurden exaktere Berechnungen mit einem von L. Weinhardt und O. Fuchs entwickelten Programm angestellt. Diese bestätigen die Ergebnisse der Abschätzung. Zudem wurde festgestellt, dass die inelastische freie Weglänge λ keinen signifikanten Einfluss auf die Modellrechnungen hat. Die gemessenen Intensitäts-Änderungen konnten zwar mit mehreren leicht verchiedenen Modellen erklärt werden, allerdings führte nur ein kugelförmiges Teilchen-Modell auch zu den richtigen Intensitätsverhältnissen der einzelnen S 2p-Komponenten. Weiterhin konnte beobachtet werden, dass die elektronische Bandlücke größer ist als die optische Bandlücke. Bei den PES-Messungen wurden einige wichtige Einflüsse sichtbar. So spielen strahlenbedingte Effekte eine große Rolle. Kenntnisse über die Zeitskala solcher Effekte ermöglichen PES-Aufnahmen mit guter Signal-Qualität und erlauben eine Extraploation zur Situation ohne Strahlenschaden. Auch die Dünnschicht-Präparation beeinflusst die Spektren. Beispielsweise zeigten mit Elektrophorese hergestellte Filme Hinweise auf Agglomeration. Schichten, die per Tropfen-Deposition erzeugt wurden, weisen spektrale Änderungen am Rand der Probe auf, und Filme aus Nanoteilchen-Pulver waren nicht homogen. Mikro-Raman Experimente, die in Kollaboration mit Dr. M. Schmitt und Prof. W. Kiefer durchgeführt wurden, ließen große Unterschiede in den Spektren von Nanoteilchen und TG in Lösung erkennen. Dies wurde vor allem auf das Fehlen von S – H –Bindungen zurückgeführt und zeigt damit, dass alle TG-Moleküle verwertet oder ausgewaschen wurden. N2 - Very small, thioglycerol (TG)-capped CdS nanoparticles were synthesized by a wet chemical technique and investigated in the framework of this thesis. Also glutathione-capped particles were investigated for a comparison of the capping agents. High-resolution photoelectron spectroscopy using high-brilliance synchrotron radiation was applied as the major tool for the characterization of these particles. Additionally, the particles were investigated with UV-VIS absorption spectroscopy, XPS using a laboratory source, valence band photoemission spectroscopy (VBPES), near-edge x-ray absorption spectroscopy (NEXAFS), and micro-Raman spectroscopy to address various aspects of the particles. In the beginning, an overview on size quantization effects is given to create a theoretical background behind the work presented in this thesis. Furthermore, an overview of various conventional techniques for size determination is presented. Exact information about size, shape and size distribution of nanoparticles is not yet achievable because of experimental limitations of the various size determination methods. Nanoparticles, with a range of sizes from 1.1 to 4. 2 nm, were synthesized using non-aqueous preparation and a TG capping. It is demonstrated that the use of the non-aqueous wet chemical synthesis method enables the production of very small particles and prohibits the aging of the particles. Furthermore, TG capping leads to a significant improvement for a narrow size distribution. Moreover, the results are very reproducible with TG capping and non-aqueous synthesis. Monodispersed particles can be produced by a size selective precipitation method, however, the reproducibility is questionable due to the aqueous medium of the synthesis in this case. High-resolution photoemission measurements on the small particles, i.e., 1.1 nm (CdS-A), 1.4 nm (CdS-B), 1.7 nm (CdS-C), and 1.8 nm (CdS-D, glutathione-capped), revealed five components as constituents of the S 2p signal after a careful data evaluation. Furthermore, it was observed that the particles with different sizes and capping show differences in the photoemission spectra and also in the beam damage behaviour. The different components of CdS-B were assigned as S atoms with different Cd neighbors, S atoms from thiol and S atoms in a partially oxidized state, based on the observed intensity changes of these components as a function of photon energy and beam damage, and on previous photoemission work on CdS nanoparticles [23, 45]. Furthermore, it was found that this assignment cannot be directly transferred to other particles. A new approach of structural model-based photoemission intensity calculations in comparison with the experimental data is presented. This enables us to understand subtle features in the photoemission spectra, in particular the intensity changes of the different components as a function of photon energy and beam exposure. This approach is especially applied to CdS-B (as some structural information for this particle is avialable from XRD), using three different structural models. It is found that a structural model with 33 S atoms can explain the experimental intensity changes of CdS-B. Furthermore, it is found that the photoemission spectra can be used to determine the particle size indirectly, as other plausible models show significant deviation from the experimental data. To study the various aspects by calculations, such as the influence of the particle shape and of the value of the mean free path, a program developed with L. Weinhardt and O. Fuchs is used for the intensity calculations. In order to determine a reasonable value of the mean free path for the used photon energies, two different equations from previous reports (Seah et al. and Powell et al.) are applied. As average mean free path values for the two photon energies we chose 5.5 ± 2 Å (254 eV) and 14 ± 2 Å (720 eV). The program calculation confirms the result of simple “manual” calculations of the different models. Moreover, it is tested that the value of , used in the calculations does not produce any significant influence on the calculation results. Another interesting feature is derived from the calculations that a model with a rather round shape produces similar intensity ratios for the different components to those of the data. Thus this new approach of analysis of photoemission spectra offers a way to determine particle sizes and to some extent to give an impression of the approximate particle shape. Furthermore, it is observed that the electronic band gap is larger compared to the optical band gap, which was attributed to an enhanced electron-hole correlation for optical absorption in small particles. The XPS experiments performed in the laboratory using an x-ray tube, show that the thin films produced from a freshly synthesized nanoparticle solution are fairly homogeneous and non-charging. Moreover, annealing experiments indicated that TG-capped particles posses less thermal stability as compared to MPA-capped particles. It was demonstrated that beam-induced effects play a major role. However, the knowledge of the time scale for such effects gives the possibility to record photoemission spectra with fairly good signal quality and to extrapolate to zero radiation damage. Further, particles with different sizes and capping show different beam damage behaviour. The thin film preparation by electrophoresis results in significant changes in the spectrum indicating agglomeration, while the drop-deposition technique points towards spectral changes on the rim of the sample, which can be avoided by focusing the radiation to the centre of the deposited dried drop. Micro-Raman experiments carried out in collaboration with C. Dem, Dr. M. Schmitt and Prof. W. Kiefer exhibited major differences in the spectra of nanoparticles as compared to those of the capping molecule thioglycerol. For instance, the absence of the S-H vibrational modes indicates the consumption or removal of all unreacted capping molecules. There is definitely a need for further detailed investigations concerning various interesting aspects of this work. For instance, it would be of significance to extend the program calculations to more models. Also more information about the band gap opening has to be gathered in order to find out the reason for the larger electronic band gap as compared to the optical band gap. The photoemission analysis approach using a model calculation has to be extended to differently prepared nanoparticles, in particular, to address the differences in the location of the various species in the particle as a function of preparation. The efforts of XRD simulations by C. Kumpf et al. [50] may reveal significant new information about the particle size and the size distribution. It can be expected that the program calculations, if extended to more models, can prove the potential of photoelectron spectroscopy to serve as a tool for size and shape determination of nanoparticles, which is a new contribution to the investigation of nanoparticles. KW - Cadmiumsulfid KW - Nanopartikel KW - Nanopartikel KW - Photoemission KW - XRD KW - UV-VIS KW - nanoparticles KW - XPS KW - monodispersity KW - UV-VIS KW - Photoemission Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-13395 ER -