TY - THES A1 - Anneser, Katrin T1 - Elektrochemische Doppelschichtkondensatoren zur Stabilisierung fluktuierender photovoltaischer Leistung T1 - Electric double layer capacitors for stabilizing intermittent photovoltaic power N2 - Der Ausbau der regenerativen Energiequellen führt vermehrt zu unvorhersehbaren Schwankungen der erzeugten Leistung, da Windkraft und Photovoltaik von natürlichen Bedingungen abhängen. Gerade Kurzzeitfluktuationen im Sekunden- bis Minutenbereich, die bei Solarzellen durch die Verschattung von vorüberziehenden Wolken zustande kommen, wird bislang wenig Beachtung geschenkt. Kurzzeitspeicher müssen eine hohe Zyklenstabilität aufweisen, um zur Glättung dieser Leistungsfluktuationen in Frage zu kommen. Im Rahmen der vorliegenden Dissertation wurden elektrochemische Doppelschichtkondensatoren für die Kopplung mit Siliziumsolarzellen und organischen Solarmodulen mit Hilfe von Simulationen und Messungen untersucht. Zusätzlich wurden grundlegende Fragestellungen zur Prozessierung und Alterung von Doppelschichtkondensatoren im Hinblick auf ein in der Literatur bereits diskutiertes System betrachtet, das beide Komponenten in einem Bauteil integriert - den sogenannten photocapacitor. Um die Druckbarkeit des gesamten elektrochemischen Doppelschichtkondensators zu ermöglichen, wurde der konventionell verwendete Flüssigelektrolyt durch einen Polymer-Gel-Elektrolyten auf Basis von Polyvinylalkohol und einer Säure ersetzt. Durch eine Verbesserung der Prozessierung konnte ein größerer Anteil der spezifischen Fläche der porösen Kohlenstoffelektroden vom Elektrolyten benetzt und somit zur Speicherung genutzt werden. Die Untersuchungen zeigen, dass mit Polymer-Gel-Elektrolyten ähnliche Kapazitäten erreicht werden wie mit Flüssigelektrolyten. Im Hinblick auf die Anwendung im gekoppelten System muss der elektrochemische Doppelschichtkondensator den gleichen Umweltbedingungen hinsichtlich Temperatur und Luftfeuchte standhalten wie die Solarzelle. Hierzu wurden umfangreiche Alterungstests durchgeführt und festgestellt, dass die Kapazität zwar bei Austrocknung des wasserhaltigen Polymer-Gel-Elektrolyten sinkt, bei einer Wiederbefeuchtung aber auch eine Regeneration des Speichers erfolgt. Zur passenden Auslegung des elektrochemischen Doppelschichtkondensators wurde eine detaillierte Analyse der Leistungsfluktuationen durchgeführt, die mit einem eigens entwickelten MPP-Messgerät an organischen Solarmodulen gemessen wurden. Anhand der Daten wurde analysiert, welche Energiemengen für welche Zeit im Kurzzeitspeicher zwischengespeichert werden müssen, um eine effiziente Glättung der ins Netz einzuspeisenden Leistung zu erreichen. Aus der Statistik der Fluktuationen wurde eine Kapazität berechnet, die als Richtwert in die Simulationen einging und dann mit anderen Kapazitäten verglichen wurde. Neben einem idealen MPP-Tracking für verschiedene Arten von Solarzellen und Beleuchtungsprofilen konnte die Simulation auch die Kopplung aus Solarzelle und elektrochemischem Doppelschichtkondensator mit zwei verschiedenen Betriebsstrategien nachbilden. Zum einen wurde ein fester Lastwiderstand genutzt, zum anderen eine Zielspannung für den Kurzzeitspeicher und somit auch die Solarzelle vorgegeben und der Lastwiderstand variabel so angepasst, dass die Zielspannung gehalten wird. Beide Betriebsmethoden haben einen Energieverlust gegenüber der MPP-getrackten Solarzelle zu verzeichnen, führen aber zu einer Glättung der Leistung des gekoppelten Systems. Die Simulation konnte für Siliziumsolarzellen mit einem Demonstratorversuch im Labor und für organische Solarzellen unter realen Bedingungen validiert werden. Insgesamt ergibt sich eine vielversprechende Glättung der Leistungsfluktuationen von Solarzellen durch den Einsatz von elektrochemischen Doppelschichtkondensatoren. N2 - The increased usage of regenerative energy sources leads to more unpredictable fluctuations in power output, as wind power and photovoltaics depend on natural conditions. Especially short-term fluctuations in the range of seconds to minutes, which occur in solar cells due to the shading by passing clouds, have received little attention so far. Corresponding short-term storage units that can be used to smooth these power fluctuations must have a high cycle stability. In the scope of this thesis the suitability of electrochemical double layer capacitors for coupling with silicon solar cells and organic solar modules was investigated with simulations and measurements. Processing methods and aging of electrochemical double layer capacitors in respect to an integrated system consisting of both components - already discussed in the literature as the so-called photocapacitor - were considered. As the liquid electrolyte was replaced by a polymer gel electrolyte based on polyvinyl alcohol and an acid in order to enable printability of the entire electrochemical double-layer capacitor. An increase of the capacitance to the level of the capacitance for electrodes with liquid electrolytes was achieved by improved processing in which a larger proportion of the specific area of the porous carbon electrodes could be wetted by the electrolyte and thus used for storage. In the application as coupled system the electrochemical double-layer capacitor must withstand the same environmental conditions with regard to temperature and humidity as the solar cell. Extensive aging tests were carried out and it was found that, although the capacitance decreases when the water-containing polymer gel electrolyte dries out, remoistening also regenerates the storage capacitance. A detailed analysis of the power fluctuations, which were measured under real conditions with small organic solar modules using a specially developed MPP measuring device, was carried out to determine the appropriate characteristics of the electrochemical double layer capacitor. Using a mathematically smoothed mean curve, it was determined which amounts of energy have to be stored in the short-term storage device for which time in order to achieve the smoothed curve. From the statistics of the fluctuations a capacitance could be calculated which was used as a guide value in the simulations and could then be compared to the impact of other capacities. In addition to ideal MPP tracking for different types of solar cells and lighting profiles, the simulation was also able to model the coupling of solar cell and electrochemical double layer capacitor with two different operating strategies. On the one hand a fixed load resistance was used, on the other hand a target voltage for the short-term storage device and thus also for the solar cell was specified. The load resistance was variably adapted so that the target voltage was reached. Both operating methods show an energy loss compared to the MPP tracked solar cell without storage component, but lead to smoothing of the power output of the coupled system. The simulation could be validated for silicon solar cells with a demonstrator test in the laboratory and for organic solar cells on the external test setup under real conditions. Overall, the use of electrochemical double layer capacitors results in a promising smoothing of the power fluctuations of solar cells. KW - Energie KW - Photovoltaik KW - Energiespeicher Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-199339 ER - TY - THES A1 - Linder, Susanne T1 - Räumliche Diffusion von Photovoltaik-Anlagen in Baden-Württemberg T1 - Spatial diffusion of photovoltaic installations in the German federal state of Baden-Württemberg N2 - Seit dem Jahr 2000 ist die Anzahl an installierten Photovoltaik-Anlagen in Deutschland – dank günstiger politischer Rahmenbedingungen – rasant von 76 MWp auf 24.820 MWp in 2011 gestiegen. Trotz bundesweit einheitlicher finanzieller Förderbedingungen durch das Erneuerbare-Energien-Gesetz existieren jedoch räumliche Unterschiede in der Anzahl an installierten Photovoltaik-Anlagen pro Einwohner, sowohl auf Ebene der Bundesländer, als auch zwischen einzelnen Gemeinden einer Region. In der vorliegenden Arbeit wird die räumliche Diffusion von Photovoltaik-Anlagen in Baden-Württemberg untersucht. Ziel ist zum einen die Ursachen für die räumlichen Unterschiede in der Photovoltaik-Diffusion aufzudecken. Zum anderen ist das Ziel zu überprüfen, ob ein Nachbarschaftseffekt der Photovoltaik-Diffusion existiert. Dies wird mit Hilfe quantitativer und qualitativer Methoden untersucht. Mit Hilfe der räumlichen Autokorrelationsanalyse wird gezeigt, dass sich die Anzahl an Photovoltaik-Anlagen pro Einwohner in den Gemeinden Baden-Württembergs signifikant unterscheidet. Es existieren Cluster von Gemeinden mit besonders hoher Photovoltaik-Nutzung (Hot Spots) und Cluster von Gemeinden mit besonders niedriger Photovoltaik-Nutzung (Cold Spots). Hot Spot-Gemeinden befinden sich zu 95% im ländlichen Raum und Cold Spot-Gemeinden zu 85% im Verdichtungsraum. Die Ergebnisse der räumlichen Regressionsanalyse und der Fallstudie in der Region Heilbronn-Franken zeigen, dass die Unterschiede in der Dichte der Photovoltaik-Anlagen pro Einwohner erstens auf Unterschiede in der Siedlungsstruktur zurückzuführen sind (Anteil an Ein- und Zweifamilienhäusern, Anteil an Neubauten, Anzahl an Viehbetrieben pro Einwohner), zweitens auf Unterschiede im Sozialgefüge (Anteil an Familien) sowie drittens auf den Nachbarschaftseffekt der Diffusion. Aus den Experteninterviews geht hervor, dass zudem weitere lokale Voraussetzungen gegeben sein müssen, damit es zu einer schnellen Photovoltaik-Diffusion kommt. Eine wichtige Rolle spielen die Landwirte, die häufig als Innovatoren auftraten, sowie sog. Change Agents, die den Diffusionsprozess anstoßen und bewusst fördern. Zu letzteren zählen auf lokaler Ebene aktive Bürgermeister, Solarvereine, Photovoltaik-Unternehmer oder Elektroinstallateure, auf regionaler Ebene Maschinenringe und Energieagenturen. Die Modellierung und Analyse der Photovoltaik-Diffusion in den einzelnen Gemeinden von 2000 bis 2030 zeigt für das Jahr 2009, dass die Gemeinden einer Raumkategorie unterschiedliche Diffusionsprofile aufweisen. Je ländlicher eine Gemeinde ist, desto weiter ist tendenziell der Diffusionsprozess fortgeschritten: In Gemeinden des ländlichen Raums befindet sich die Photovoltaik-Diffusion meist bereits im Early Majority-Stadium, in Gemeinden des Verdichtungsraums ist die Photovoltaik-Diffusion dagegen überwiegend erst am Ende des Early Adopter-Stadiums angelangt. Der Innovationseffekt, der angibt, wie stark die Anzahl an Photovoltaik-Anlagen unabhängig von den bereits installierten Anlagen zunimmt, ist im suburbanen Raum und im ländlichen Raum am höchsten. Der Imitationseffekt, der angibt, wie stark die Zunahme neu installierter Photovoltaik-Anlagen von bestehenden Anlagen in einer Gemeinde abhängt, steigt dagegen von der Stadt zum Land an. Durch den Vergleich der Hot Spot-Gemeinden mit den übrigen Gemeinden des ländlichen Raums wird deutlich, dass die Imitation in den Hot Spot-Gemeinden höher liegt. Dies lässt darauf schließen, dass ein Nachbarschaftseffekt der Photovoltaik-Diffusion zwischen den Gemeinden existiert, da die Lage innerhalb eines Hot Spots zu einer erhöhten Wahrnehmung von Photovoltaik-Anlagen und einem häufigeren Austausch mit Photovoltaik-Besitzern führt und damit die Photovoltaik-Diffusion fördert. Vor dem Hintergrund des Klimawandels und der knapper werdenden fossilen Ressourcen gilt in Deutschland das Ziel, die Nutzung erneuerbarer Energien und damit auch der Photovoltaik weiter voranzutreiben. Diese Arbeit zeigt, dass lokale Einflussfaktoren entscheidend für das Entstehen räumlicher Unterschiede in der Photovoltaik-Nutzung sind. Die Kenntnisse dieser Unterschiede, deren Ursachen sowie die Bedeutung des Nachbarschaftseffekts können eine Grundlage für gezielte Förderung oder Marketingmaßnahmen zur weiteren Diffusion von Photovoltaik-Anlagen bieten. N2 - Since 2000, the number of photovoltaic systems installed in Germany has significantly increased from 76 MWp to 24,820 MWp in 2011. This can be attributed to a favourable policy framework. Despite a nationaly uniform financial incentive scheme supported by the Renewable Energies Act (EEG), spatial differences in the number of photovoltaic systems installed per capita can be observed between the federal states as well as among individual municipalities. This study analyses the spatial diffusion of photovoltaic installations in the German federal state of Baden-Württemberg. The first aim of the study is to identify the reasons for spatial differences in diffusion. The second aim is to examine whether there is a neighbourhood effect in the spatial diffusion of photovoltaic installations. The study is based on quantitative and qualitative methods. The analysis of spatial autocorrelation shows that the number of photovoltaic installations per capita differs significantly among the municipalities in Baden-Württemberg. The analysis reveals the presence of clusters of municipalities with above average photovoltaic development (Hot Spots) and below average photovoltaic development (Cold Spots). The results show that 95 % of the Hot Spot municipalities are located in rural areas while 85 % of the Cold Spot municipalities are found in urban agglomerations. Both the results of the spatial regression analysis and the case study of the region Heilbronn-Franken, indicate that differences in the density of photovoltaic installations per capita arise for three main reasons: firstly, because of differences in the settlement structure (percentage of detached and semi-detached houses, percentage of new houses, percentage of livestock farms), secondly, because of differences in the social structure (percentage of families), and thirdly, because of the neighbourhood effect of diffusion. Expert interviews identified that additional local conditions play an important role in promoting the diffusion of photovoltaic installations. Particularly farmers play a crucial role in the diffusion as they often act as innovators. The photovoltaic diffusion process is often triggered and promoted by change agents. On a local level, change agents are active mayors, solar initiatives, photovoltaic entrepreneurs or electricians. On a regional level, these are machinery rings or energy agencies. The results of the model for the analysis (from 2000 to 2030) of the diffusion of photovoltaic installations in the municipalities show that in 2009 municipalities of different spatial categories display different diffusion profiles. The more rural a municipality is, the more advanced the diffusion process: municipalities in rural areas have mostly reached the point of inflection of the diffusion curve and adopters now belong to the Early Majority. Municipalities in urban areas still belong to the Early Adopters. The coefficient of innovation indicating the extent at which the number of photovoltaic installations increases independently from other installations, is highest in suburban and rural areas. The coefficient of imitation indicating the strength of dependence in the development of new photovoltaic installations from existing ones, increases from urban to rural areas. The comparison of Hot Spot municipalities with the remaining municipalities of the rural areas shows that the coefficient of imitation is higher in Hot Spot municipalities. Thus, one can conclude that there is a neighbourhood effect in the diffusion of photovoltaic installations among municipalities. The position within a Hot Spot advances the perception of photovoltaic installations and increases interaction and communication among photovoltaic owners promoting the diffusion of the technology. In the context of climate change and the limited availability of fossil fuels, the use of renewable energies e.g. photovoltaic installations should be further encouraged in Germany. This study shows that local conditions significantly impact the development of spatial differences in the use of photovoltaic technology. Understanding the reasons for these spatial differences and the neighbourhood effect can help to define well-directed incentives and to develop marketing strategies to further promote the diffusion of photovoltaic installations. T3 - Würzburger Geographische Arbeiten - 109 KW - Baden-Württemberg KW - Photovoltaikanlage KW - Räumliche Verteilung KW - Räumliche Diffusion KW - Nachbarschaftseffekt KW - Räumliche Autokorrelation KW - Bass-Modell KW - Diffusion von Innovationen KW - Photovoltaik KW - spatial diffusion KW - photovoltaic KW - neighbourhood effect KW - spatial autocorrelation KW - Bass Model KW - diffusion of innovation Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-77789 ER - TY - THES A1 - Mayerhöffer, Ulrich T1 - Synthese, Eigenschaften und funktionale Anwendungen von NIR absorbierenden Squarainen T1 - Synthesis, Properties and Functional Applications of NIR Absorbing Squaraines N2 - Zusammenfassend lässt sich festhalten, dass die in dieser Abreit vorgestellten Squaraine herausragend gute NIR-Absorptions- und NIR-Emissionseigenschaften aufweisen, die sie für zahlreiche Anwendungen interessant machen. Darüber hinaus konnte gezeigt werden, dass ihre besondere cis-Konfiguration und ihr daraus resultierendes Dipolmoment zu vorteilhaften Anordnungen in dünnen Filmen und in Blends mit PCBM führen. Diese Strukturen zeigen für dipolare Moleküle beeindruckende Exzitonen- und Ladungstransporteigenschaften, die vielversprechende Anwendungen in der organischen Elektronik wie in hier untersuchten lösungsprozessierten BHJ-Solarzellen oder auch in OFETs erwarten lassen. N2 - Concluding the results of the present work, the here descript acceptor-substituted squaraines exhibit extremely favourable NIR absorption and emission properties which make them to ideal candidates for a broad variety of functional applications. Furthermore, the additional acceptor functions provoke a cis-configuration, resulting in a permanent ground state dipole moment which becomes a dominating ordering force in supramolecular arrangements of those squaraine dyes in solution as well as in thin organic films and in blends with PCBM. These structures feature unprecedented exciton and charge carrier mobilities for dipolar molecules with promising properties for the application in organic photovoltaics, as demonstrated in this work and for possible future applications such as OFETs. KW - Supramolekulare Chemie KW - Squaraine KW - Photovoltaik KW - NIR KW - Organische Chemie KW - Organic Chemistry KW - supramolecular Chemistry KW - Squaraine KW - Photovoltaic KW - NIR Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-69428 ER -