TY - THES A1 - Loisel, Claudine T1 - Korrosionsempfindliche Dosimetermaterialien zur Überwachung der Umweltbedingungen an Kulturgütern T1 - Corrosion sensitive dosimeter material for environmental condition control in culture heritage N2 - Das Ziel dieser Arbeit war es, ein neues Dosimetermaterial zu entwickeln, das schneller reagiert als der klassische Glassensor. Einen vielversprechenden Ansatz dafür bietet der Sol-Gel Prozeß, mit dem dünne Schichten hergestellt werden können. Erste Versuche mit transparenten Schichten einer glasähnlichen Zusammensetzung (mit einem hohen Anteil an K und Ca) waren nicht erfolgreich, da eine deutliche Erhöhung der Reaktivität nicht erreicht wurde. Schichten, die einen sehr hohen Ca-Anteil aufweisen, zeigten allerdings die gewünschte Empfindlichkeit gegen Umwelteinflüsse. Die neuen „Rapid-Sensoren“ werden aus einem vorkonsensierten SiO2-Sol (Silizium (IV) Oxid-Sol) und Ca(NO3)2 4H2O in Aceton (Molverhältnis Ca : Si = 10 : 1) hergestellt. Objektträger werden mit diesem Sol beidseitig beschichtet. Die Tauchbeschichtung und die Temperung (5 Minuten bei 600 °C) wurden auf hohe Empfindlichkeit gegen Feuchtigkeit und Schadgase (Screening Test in einer Klimakammer) optimiert. Die neuen Sensoren sind im sichtbaren Spektralbereich nicht transparent, sondern opak, können aber wie die klassischen Glassensoren mit IR-Spektroskopie (in Transmission) ausgewertet werden, wobei der Anstieg der OH-Bande bei 3300 cm-1 als Mass für den Korrosionsfortschritt (genannt E-Wert) dient. Die aktive Sensorschicht setzt sich aus kristallinen und amorphen Bestandteilen zusammen. Die Zusammensetzung und Morphologie der Kristallphase wurde weitestgehend charakterisiert. Mit Lichtmikroskopie lässt sich die Oberfläche des Rapid-Sensors als eine Vielzahl kleiner polygoner Kristalle charakterisieren, für die im REM beobachtet verschiedene Wachstumsstufen erkennbar sind. Mit Hilfe der EDX-Analyse und ICP-AES wurden Si, O, Ca und Na als die Hauptelemente der Schicht bestimmt. Mit SNMS-Tiefenprofil konnte eine Diffusion von Na aus dem Objektträger in die Schicht nachgewiesen werden, was zu einer besonders guten Haftung führt. Mittels Röntgendiffraktometrie, IR- und Raman-Spektroskopie lassen sich Informationen über die Struktur der Schicht erhalten: die Kristallphase besteht aus einer Mischung aus Calciumoxid und Calcium-silicat-en, die mit XRD schwer zu unterscheiden sind. Auch im infraroten Spektralbereich weisen die Si-O-Schwingungen auf silicathaltige, Bestandteile in der amorphen Schicht hin. Für die Kalibrierung des neuen Dosimetermaterials sind Bewitterungen unter kontrollierten Bedingungen grundlegend notwendig. Dazu wurde ein Bewitterunsprogramm (I) mit hoher Feuchte und Temperatur (40 °C, 98 % r.F.) sowie ein zweites mit Zugabe von SO2 als Schadgas (II) gewählt. Beide Programme beschleunigen die Umweltwirkung im Vergleich zu Realbedingungen und haben sich in anderen Versuchen mit klassischen Glassensoren bewährt. Zusammenfassend lässt sich aus den Bewitterungsversuchen feststellen, dass der neue Sensor integrativ auf Temperatur, Feuchte, und Schadgas reagiert. Entsprechend der Reaktion des klassischen Sensors führt eine Temperatur / Feuchte- Bewitterung zur Bildung von CaCO3-Kristallen, während bei Anwesenheit von SO2 bevorzugt Gipskristalle gebildet werden. Diese Parallelen lassen den Schluß auf ein vergleichbares Reaktionsprinzip zu, obwohl die Reaktion der Calciumsilicate, aus denen die Schicht besteht, nur bedingt mit der für Glas typischen Verwitterung vergleichbar ist. Mit REM kann man bei Rapid-Sensoren beobachten, dass die Reaktion am Rand der Kristalle beginnt und in die Tiefe fortschreitet, bis zur vollständigen Umsetzung (Sättigung). Die kristallinen Korrosionsprodukte breiten sich im weiteren Verlauf auch auf der amorphen Schicht aus. Der Mechanismus ist nicht reversibel und entspricht damit nicht dem für poröse SiO2-Schichten beschriebenen Alterungprozeß. Erste Sensorstudien unter natürlicher Bewitterungsbedingungen ermöglichen einen Vergleich mit klassischen Glassensoren und umreissen das künftige Einsatzspektrum. Expositionen in der ISC-Außenstelle Bronnbach und im Grünen Gewölbe in Dresden zeigen, dass die Rapid-Sensoren schneller reagieren als klassische Glassensoren (Steigerung um etwa Faktor 3). Unter moderat korrosiven Bedingungen im Innenraum sind 4 Wochen Expositionszeit günstig (mindestens 3 Monate für Glassensoren) während im Außenraum Rapid-Sensoren innerhalb von 7 Tagen ansprechen (einige Wochen für herkömmliche Glassensoren). N2 - The goal of this work was to develop a new dosimeter material, which reacts faster than the classical glass sensor. The sol-gel process offers a promising approach for the preparation of thin layers. First attempts with transparent layers with a composition similar sensitive glass (with a high concentration of K and Ca) were not successful, since a clear increase of reactivity was not reached. Layers, which exhibit a very high calcium concentration finally showed the desired sensitivity to environmental influences. The new "Rapid-Sensor" is prepared from a pre-condensed SiO2-Sol (silicon (IV) oxide Sol) and Ca(NO3)24H2O in acetone (molar ratio Ca : Si = 10 : 1). Microscopic slides are coated with this sol from both sides by dip coating. The curing process (5 minutes at 600 °C) has been optimised for high sensitivity to humidity and pollutants (screening test in a climatic chamber). The new sensors are not transparent, but opaque. Nevertheless, they can be evaluated like the classical glass sensors with IR spectroscopy (in transmission mode), whereby the increase of the OH-band at 3300 cm-1 serves as a measure for the corrosion progress (so-called E-value). The sensitive coating consists of crystalline and amorphous components. The composition and morphology of the crystal phase were characterised as far as possible. With light microscopy the surface of the Rapid-Sensor can be described as a multiplicity of small polygonal crystals, for which in the SEM different growth steps are recognisable. With EDX and ICP AES analysis, the elements Si, O, Ca were determined as the main elements of the layer. With SNMS depth profile the diffusion of Na from the support (microscopic slide) into the layer can be proven, what leads to a particularly good adhesion. By means of X-ray, IR and Raman spectroscopy information about the structure can be received: the crystal phase consists of a mixture of calcium oxides and silicates, which can not be differentiated further with XRD. In the infrared spectrum signals designated to vibrations of Si-O confirm that silicates are present in the amorphous layer. For the calibration of the new dosimeter material, weathering experiments under controlled conditions are fundamentally necessary. Therefore, an accelerated ageing program (I) with high humidity and temperature (40 °C, 98 % r.F.) as well as a second program with the addition of SO2 as pollutants (II) has been selected. Both programs accelerate the environmental effect as compared with natural conditions and have been applied in previous experiments with classical glass sensors. As a conclusion, it can be stated from the environmental testing that the new sensor integrates the impact of temperature, humidity, and pollutants. Similar to the reaction of the classical sensor weathering at high temperature and high humidity leads to the formation of CaCO3 crystals, whereas in the presence of SO2 gypsum crystals are preferably formed. These similarities permit the conclusion that a comparable reaction principle might exist, although the reaction of the calcium silicate, of which the layer consists, is not necessarily comparable with the typical glass weathering. With SEM one can observe that the reaction of Rapid-Sensors begins at the edge of the crystals and progresses into depth, up to complete conversion (saturation) has been achieved. The crystalline corrosion products spread over the amorphous layer. The mechanism is not reversible and does not correspond thereby to the ageing process described for porous coatings of SiO2. First sensor studies under natural weathering conditions make a comparison possible with classical glass sensors and outline the future spectrum of use. Exposures in Bronnbach and in the Grünen Gewölbe Museum (Green Dome) in Dresden show that the Rapid-Sensors react faster than classical glass sensors (about three times increase). Under moderately corrosive conditions indoor 4 weeks exposure time are requested (at least 3 months for glass sensors). For outdoor applications Rapid-Sensors respond favourably within 7 days (some weeks for conventional glass sensors). KW - Kulturgut KW - Korrosion KW - Feuchtigkeitssensor KW - Temperatursensor KW - Gassensor KW - Dosimeter KW - Sensor KW - Korrosionsempfindliche KW - Glas KW - Silicate KW - dosimeter KW - sensor KW - corrosion sensitive KW - glass KW - silicate Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-10835 ER - TY - THES A1 - Griebel, Dragan T1 - Fluoreszente, hybride Nanosensoren auf Silicatbasis für die Bioanalytik T1 - Fluorescent, hybrid silica nanosensors for bioanalytic applications N2 - Es wurde ein Leitpartikeltyp mit hoher Fluoreszenz sowie einem Absorptionsbereich oberhalb von 600 nm evaluiert. Zur Anbindung der hochspezifisch wirkenden Antikörper wurde die Teilchenoberfläche mit Carboxylgruppen funktionalisiert. Die Darstellung dieser sphärischen, komplex aufgebauten erfolgte über eine nasschemische Synthese. Die synthetisierten Partikel besitzen eine hohe Fluoreszenzintensität, gutes Chromatographierverhalten und spezifische Beladbarkeit mit monoklonalen Antikörpern (z.B. Troponin T) auf einer mit Carboxylgruppen modifizierten Partikeloberfläche. Auf die Partikel mit dem favorisierten Fluorophor musste eine zusätzliche Silicathülle aufkondensiert werden, damit diese im Anschluss erfolgreich mit Antikörpern beladen werden konnte. Die erhaltenen partikulären Systeme wurden sowohl qualitativ als auch quantitativ charakterisiert. Die Fluoreszenzintensität dieser dotierten Kern-Schale-Partikel konnte soweit optimiert werden, dass sich klinisch relevante und noch höhere Sensitivitäten in Prüfteststreifen detektieren ließen. Weiterhin wurden neuartige Fluoralkylsilan und Fluorophor codotierte Silicat-Nanopartikel synthetisiert, die auf Anhieb eine gute untere Nachweisgrenze von Troponin erzielten. Durch UV-VIS- und Fluoreszenz-Untersuchungen sowie Konjugations- und Prüfteststreifen-Versuche konnte gezeigt werden, dass die Cokondensation des Fluoralkylsilans in einer Erhöhung von Absorption und Fluoreszenz der Partikel resultiert. Weitere Untersuchungen von zeigten, dass eine zusätzliche Oberflächenmodifizierung mit Fluoralkylsilan zu einer signifikanten Verschlechterung der Konjugationseigenschaften mit Antikörpern führt. Alternative Detekorreagenzien und -methoden wurden ebenfalls untersucht. So konnte der kationische Komplex Tris-(1,10-phenantrolin)ruthenium(II)-dichlorid erfolgreich in monodisperse Silicat-Partikel eingebaut werden. Aufgrund ihrer geringen Sauerstoffpermeabilität sind sie als impermeabler Referenzstandard in O2-Sensoren geeignet. Eine andere untersuchte Detektionsmethode basiert auf zeitaufgelöster Fluoreszenz (TRF). Hierbei werden hauptsächlich Lanthanoid-Komplexe eingesetzt. Am besten untersucht sind Europium-Komplexe, welche meistens Diketone als Liganden besitzen. Bislang konnten diese neutralen Komplexe jedoch nicht in polare Silicatpartikel-Matrizes eingebaut werden. Durch Einsatz von 3,3,3-Trifluoropropyltrimethoxysilan gelang es erstmalig, einen Europium(III)-tris-4,4,4-trifluoro-1-(2-naphthoyl)-1,3-butandion-Komplex (Eu(TNB)3) in hydrophobierte Silicat-Nanopartikeln physikalisch einzubauen. TRF-Messungen zeigten Abklingzeiten von ca. 300 µs. In diesem bislang nicht verfügbaren Partikel-Typ konnten positive Eigenschaften von Latex- und Silicatpartikeln kombiniert werden. Auch einige Porphyrinkomplexe mit langen Fluoreszenzlebensdauern sind in Silicat-Nanopartikel eingebaut worden. Der neutrale Komplex 5,10,15,20-Tetrakis(4-carboxyphenyl)-porphyrin-Pd(II) konnte nur durch vorhergehende Silanisierung erfolgreich eingebunden werden. Die erhaltenen sphärischen Partikel weisen eine Größenverteilung von 200-300 nm auf. Ein weiteres, kationisches Porphyrin (5,10,15,20-Tetrakis(N-methyl-4-pyridyl)-21,23H-porphyrin-Zn(II)) konnte ebenfalls erfolgreich in etwa 140 nm große Silicat-Nanopartikel blutungsstabil eingebaut werden. N2 - The aim was to develop monodisperse detector reagents based on nanoparticles, that can be used as biosensors for medical diagnostics and other bioanalytical applications. A particle-type with a high fluorescence intensity and an absorption range around or above 600 nm was evaluated. The particle surface was functionalized with carboxyl groups to allow for covalent attachment of specific antibodies through which the particles can bind to target molecules. The synthesis of these complex spherical particles was done following the wet-chemical Sol-Gel-Process. The particles could be adjusted to the desired requirements: high fluorescence quantum yields, good chromatographic behaviour , efficient conjugation of antibodies (e.g. Troponin T) to a carboxyl modified particle surface. The nanoparticles with the favoured fluorophore had first to be covered with an additional silica shell in order to prepare them for loading with antibodies afterwards. The resulting particles have been characterized qualitatively as well as quantitatively. Furthermore, novel silica nanoparticles have been synthesized by cocondensation of a fluoroalkylsilane and a fluorophore. UV-VIS- and fluorescence spectroscopy as well as conjugational and biosensor tests showed that the cocondensation has positive effects on the absorption and on the fluorescence of the particles. Alternative detection reagents and methods have also been investigated. Thus, the cationic complex Tris-(1,10-phenantrolin)ruthenium(II)-dichloride could successfully be integrated into monodisperse silica particles. These particles are suitable as a standard substrate in O2-sensors because of their low oxygen permeability. The required physical entrapment quantity of the complex as well as the desired low permeability could be demonstrated successfully. Time resolved flourescence (TRF) was applied as an additional detection method. Mainly lanthanoid complexes are used within this method. Most commonly used are Eu(III)-b-diketonate complexes. Up to now, these neutral complexes could not be integrated into the polar silica particle matrix. For the first time, an Europium(III)-tris-4,4,4-trifluoro-1-(2-naphthoyl)-1,3-butandion-complex (Eu(TNB)3 could be embedded into silica particles hydrophobized with 3,3,3-Trifluoropropyltrimethoxysilane. The embedment into the 140 nm diameter nanoparticles has been proved quantitatively as well as qualitatively TRF measurements detected a fluorescence lifetime of approximately 300 µs. In this - up to now- unique particle type the positive properties of latex particles and silica particles could be combined. Some porphyrin complexes possess long fluorescence lifetimes and, therefore, have been investigated. The neutral 5,10,15,20-Tetrakis(4-carboxyphenyl)-porphyrin-Pd(II) complex could only be integrated successfully into silica nanoparticles after having been silanized. The resulting spheric particles have a particle size distribution of 200- 300 nm. Another cationic porphyrin (5,10,15,20-Tetrakis(N-methyl-4-pyridyl)-21,23H-porphyrin-Zn(II)) could also be integrated successfully and without bleeding into 140 nm sized monodisperse silica particles. KW - Silicate KW - Nanopartikel KW - Fluoreszenzmarkierung KW - Biologisches Material KW - Analyse KW - Nanosilicatpartikel KW - hybrid KW - Fluoreszenz KW - nano KW - nanoparticles KW - hybrid KW - fluorescence Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-6153 ER -