TY - THES A1 - Nashed, Alexander T1 - Entwicklung spinnfähiger Precursorpolymere zur Herstellung nicht-oxidischer Keramikfasern T1 - Development of spinnable precursor polymers for the production of non-oxide ceramic fibers N2 - Ausgehend von chlorhaltigem Oligosilan, erhalten durch Disproportionierung der „Disilan-Fraktion“ der Müller-Rochow-Synthese, wurde mit verschiedenen Aminen dechloriert bzw. strukturell modifiziert. Die auf diese Weise in das Oligosilan eingeführten Baugruppen wurden spektroskopisch und durch Vergleich mit geeigneten Modellverbindungen identifiziert. Vernetzungsgrad und keramische Ausbeute der erzeugten Materialen wurden bestimmt. Mit Ammoniak oder einwertigen Aminen wie Methylamin werden Produkte erhalten, die sich nicht zu Keramikfasern verarbeiten lassen. Letzteres scheitert daran, dass entweder keine signifikante Molekulargewichtserhöhung des Oligosilans erreicht wird, oder führt dazu, dass das Oligomer vergelt und damit in Toluol unlöslich wird. Durch Umsetzung des Oligosilans mit zweiwertigen Aminen wie EDA oder TMDA als Vernetzungsreagenz gelang es, eine Syntheseroute zu entwickeln, die – anders als bei der am ISC etablierten Route – keinen thermischen Vernetzungsschritt erfordert, d.h. die gesamte Synthese findet bei Temperaturen ≤200 °C statt. Hierbei wird eine kontrollierbare Erhöhung des Molekulargewichts erreicht. Die Verwendung von TMDA hat gegenüber EDA den Vorteil, dass aufgrund des Ausbleibens von Ringbildung ein höher vernetztes Polymer erhalten wird. Darüber hinaus wurde gefunden, dass Grünfasern während der Pyrolyse durch radikalisch vernetzbare Gruppen (C=C-Doppelbindungen) im Polymer stabilisiert werden können. Diese Gruppen lassen sich entweder durch Dechlorierung mit Allylamin oder durch Umsetzung mit Vinyl-Grignard-Reagenzien einführen. Allylamin erwies sich hierbei als geeigneter, da es preiswerter und leichter handhabbar ist und außerdem – im Gegensatz zu Vinyl-Grignard-Reagenzien – eine vollständige Dechlorierung des Polymers gestattet. Alle Polymere wurden auf ihre Verarbeitbarkeit zu Grün- und anschließend zu Keramikfasern untersucht. Hierbei wurde gefunden, dass die im Hinblick auf die Eigenschaften der resultierenden Keramikfasern günstigste Rezeptur in der Umsetzung eines zuvor mit DMA vollständig dechlorierten Oligosilans mit 18,2 mol-% TMDA und 40 mol-% Allylamin (bezogen auf NMe2-Gruppen) besteht. Die aus diesem Polymer erhaltenen Keramikfasern zeigen die für noch nicht technisch ausgereifte, im Stadium der Entwicklung befindliche Fasern typischen Festigkeiten und entsprechen damit denjenigen, die auf der am ISC bereits etablierten Route erhältlich sind. Dies macht sie zu aussichtsreichen Kandidaten für die weitere Optimierung. N2 - Based on chlorine containing oligosilane which is synthesized via disproportionation of the “disilane fraction” of the Müller-Rochow synthesis, there have been dechlorinations respectively structural modifications with different amines. The structural components introduced into the oligosilane by this means were identified spectroscopically and by comparison with appropriate model compounds. The degree of crosslinking and the ceramic yield of the generated materials were detected. By the use of ammonia or primary amines like methylamine products are generated which cannot be converted to ceramic fibers. The latter fails because either no significant increase of the molecular weight of the oligosilane is obtained or the oligosilane gels and becomes insoluble in toluene. By the reaction of oligosilane with secondary amines like EDA or TMDA as a crosslinking reagent it succeeded to develop a synthesis route which – different from the route established at the ISC – doesn’t require any thermic crosslinking step what means that the whole synthesis takes place at temperatures ≤200°C. In this connection a controllable increase of the molecular weight is reached. The use of TMDA has the advantage over EDA that due to the absence of ring formation a higher cross-linked polymer is obtained. Furthermore it was found that green fibers can be stabilized during pyrolysis with radically curable groups (C=C double bonds) inside the polymer. These groups can be introduced either by dechlorination with allylamine or by reaction with vinyl Grignard reagents. Allylamine was proven to be more suitable because it is low-cost and easier to handle and besides – in comparison to vinyl Grignard reagents – it allows a complete dechlorination of the polymer. All polymers were analyzed concerning their processability to green and subsequent to ceramic fibers. Here it was found that the most favorable recipe with respect to the properties of the resulting ceramic fibers consists in the reaction of fully with DMA dechlorinated oligosilane with 18.2 mol-% TMDA and 40 mol-% allylamine (based on NMe2-groups). The ceramic fibers obtained from this polymer show typical stabilities as they are not yet technically mature and in the stage of development. For this reason they correlate with the ones which are already available by the established route at the ISC. This makes them to promising candidates for further optimization. KW - Keramikfaser KW - Polymerisation KW - Oligosilane KW - ceramic fibers KW - Precursorpolymer KW - SiC Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-138517 ER - TY - THES A1 - Kimmig, Stefan T1 - Herstellung und Charakterisierung von SiC-Faser-verstärktem Kupfer zur Anwendung in Hochleistungswärmesenken T1 - Manufacturing and characterisation of SiC-fibre-reinforced copper in heat sink applications N2 - Die Wandmaterialien innerhalb des Plasmagefäßes zukünftiger Fusionsreaktoren sind teilweise extremen thermischen und mechanischen Belastungen ausgesetzt. Der thermisch höchstbelastete Bereich der Wand des Torusgefäßes ist der Divertor. Hier werden die anfallende Fusionsasche (Helium) und erodierte Wandpartikel aus dem Plasma entfernt, wodurch aufgrund erhöhter Teilchen-Wand-Interaktion Wärmeflüsse von bis zu 15 MW/m² erreicht werden. Wolfram gilt momentan als ideales Wandmaterial mit direktem Plasmakontakt (Plasma-Facing-Material, PFM) für diese Beanspruchungen. Unterhalb des PFM muss die Wärme möglichst effizient in das Kühlmedium übertragen werden. Im zukünftigen Experimentalreaktor ITER wird dafür eine Kupferlegierung (CuCrZr) verwendet, welche eine hohe Wärmeleitfähigkeit besitzt und für Temperaturen von bis zu 350°C unter fusionsrelevanten Bedingungen einsetzbar ist. In dieser Konfiguration kann ITER mit einer Kühlmitteltemperatur von 150°C betrieben werden. Zur kommerziellen Energiegewinnung ist dies unzureichend, da die thermische Effizienz durch eine deutliche Anhebung der Kühlmitteltemperatur verbessert werden muss. Wird der konventionelle Ansatz einer Wasserkühlung zu Grunde gelegt, ist das Ziel die Kühlmitteltemperatur auf mindestens 300°C anzuheben. In der Folge ist CuCrZr als Wärmesenkenmaterial nicht mehr einsetzbar, da verstärkte Alterung und Festigkeitsverlust im Material auftritt. Zusätzlich vergrößern sich die thermisch induzierten Spannungen in der Komponente mit höheren Temperaturen, durch unterschiedlich große thermische Ausdehnungskoeffizienten der beteiligten Materialien. Für höhere Temperaturen stellt faserverstärktes Kupfer eine mögliche Alternative dar. Die Kombination der hohen Wärmeleitfähigkeit der Kupfermatrix mit der hohen Steifigkeit und Festigkeit von Siliziumcarbidfasern soll die nötigen thermischen und mechanischen Eigenschaften des Wärmesenkenmaterials auch für Temperaturen über 350°C gewährleisten. Im Rahmen dieser Arbeit wurden zwei unterschiedlich hergestellte SiC-Verstärkungsfasertypen hinsichtlich ihrer Eignung für die Herstellung eines Kupfer-Matrix-Komposits (CuMMC) untersucht. Die Zielstellung für das CuMMC beinhaltet eine Festigkeit von 300 MPa bei 300°C sowie eine möglichst hohe Wärmeleitfähigkeit von über 200 W m-1 K-1. Beide Parameter werden stark von der Faserfestigkeit und der Anbindung zwischen Faser und Matrix beeinflusst. Die Wärmeleitfähigkeit durch das CuMMC wird von der Kupfermatrix dominiert, wodurch geringere Faservolumenanteile von Vorteil sind. Höhere Faserfestigkeit erfordert geringere Faseranteile zum Erreichen mechanischer Vorgaben, womit die erzielbare Wärmeleitfähigkeit des CuMMCs steigt. Die Faserfestigkeit wird durch Einzel-Faser- Zugversuche validiert. Darüber hinaus ist die Anbindung zwischen Faser und Matrix essentiell, um die optimale Verstärkungswirkung durch die Fasern im CuMMC zu erzielen. Zur Faser-Matrix-Anbindung werden für jeden Fasertyp unterschiedliche Zwischenschichtsysteme verwendet, die anschließend durch Einzelfaser-Push-Out-Versuche validiert werden. Sind die Voraussetzungen von Faserfestigkeit und Anbindung für einen Fasertyp erfüllt, wird dieser für die Herstellung eines unidirektional verstärkten CuMMCs verwendet, welches bezüglich seiner mechanischen und thermischen Eigenschaften charakterisiert wird. Die mechanische Charakterisierung des CuMMCs erfolgt durch Zugversuche und dehnungsgeregelte, zyklische Versuche, wobei der Fokus neben der Festigkeit auf der Plastifizierung, Verfestigung und Schädigung innerhalb des CuMMCs liegt. Die thermische Charakterisierung erfolgt anhand der Wärmeleitfähigkeitsbestimmung sowohl parallel, als auch transversal zur Faserrichtung. Die mechanischen und thermischen Eigenschaften werden in Abhängigkeit von Faservolumenanteil und Temperatur untersucht. Um den Einfluss von längeren Betriebsphasen unter hoher thermischer Belastung analysieren zu können, wird das CuMMC bei 550°C für 400 h ausgelagert und anschließend wiederum mittels Vergleich seiner mechanischen und thermischen Eigenschaften auf mögliche Schädigungen untersucht. Zur Begutachtung von Schliff- und Bruchflächen zur Schadensanalyse stehen als bildgebende Untersuchungsmethoden neben Lichtmikroskopen ebenso Rasterelektronenmikroskope (REM) zur Verfügung. N2 - The wall materials in future fusion reactors will be operating under extreme thermal and mechanical load conditions. The divertor region of such a device is the most severely loaded component. This part is exposed to heat fluxes of up to 15 MW m-² due to the impinging plasma particle flux. Tungsten is currently considered as the best choice for the plasmafacing- materials (PFM) in the divertor region. An efficient heat sink material is required underneath the PFM for sufficient heat transfer to the cooling channels. In the research reactor ITER a copper alloy (CuCrZr) is foreseen as heat sink material, which is able to withstand temperatures of up to 350°C, corresponding to a water coolant temperature of 150°C. For the commercial use of fusion energy an increase of the thermal efficiency is necessary by increasing the coolant temperature to over 300°C. This will cause higher stresses in the connection area between PFM and the heat sink due to different coefficients of thermal expansion combined with higher temperatures. The mechanical properties of CuCrZr are insufficient for these conditions and fibre reinforced copper metal matrix composites (CuMMC) are considered as an alternative material to strengthen the critical connection area between the heat sink and the PFM. The composite should combine the high heat conductivity of a copper matrix with the high stiffness and mechanical strength of silicon-carbide fibres (SiC-fibres). During this investigation SiC-fibres of two different production principles were studied regarding their usage for the manufacturing of a CuMMC. The main goals for the CuMMC are a tensile strength of 300 MPa combined with a heat conductivity of more than 200 W m-1 K-1. Both of these parameters are affected by the single fibre tensile strength and by the bonding between the fibres and the copper matrix. The achievable heat conductivity in the CuMMC depends on the fibre volume ratio within the composite. Higher fibre strength reduces the necessary fibre volume ratio and hence increases the heat conductivity of the CuMMC. The fibre strength was validated by single fibre tension tests. Furthermore, a good bonding between fibre and matrix is necessary to optimize the fibre reinforcement, which is based on load transfer between fibre and matrix. Therefore, both fibre types were coated with interlayer systems and the effectiveness of the bonding was validated by single fibre push-outtests. For those cases where fibre strength and bonding were sufficient, a unidirectional fibre reinforced CuMMC was manufactured, who’s mechanical and thermal properties were then characterised. The mechanical tests included tensile tests and strain-controlled cycling tests which gave information about strength, plasticity, hardening and the effect of damage within the CuMMC. To verify that the CuMMC heat sink material achieves the thermal requirements, heat conductivity measurements parallel and perpendicular to the fibre direction were performed. These characterizations were done as a function of fibre volume fraction in the CuMMC and temperature. To investigate the influence of long term exposure to operation temperatures, a heat treatment was carried out for 400 h at 550°C and the mechanical and thermal properties were compared to their initial values. Different optical microscopes and scanning electron microscopes (REM) were used for the analysis of crack surfaces and grindings. For the engineering design of divertor components numerical models of the used material are required. These models need to be developed by adjusting their input parameters to fit experimental results. To that end, strain-controlled cycling tests allowed the analysis of the copper matrix hardening behaviour. This is necessary to understand stress development during operational load cycles of the CuMMC. The comparison of room temperature tests with 300°C tests showed the effects of fabrication-induced residual stress in the CuMMC. KW - Kupfer KW - Faserverstärkung KW - Metallmatrix-Verbundwerkstoff KW - Kühlkörper KW - Komposite KW - copper KW - fibre-reinforcement KW - SiC KW - heat sink KW - metall-matrix-composite KW - Siliciumcarbid KW - MMC Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-85123 ER -