TY - THES A1 - Lermer, Matthias T1 - Wachstum und Charakterisierung von Quantenpunkt-Mikrotürmchen mit adiabatischer Modenanpassung T1 - Growth and characterisation of quantum dot - micropillars with adiabatic mode transission N2 - Verschiedene Konzepte zur Realisierung einer geeigneten Umgebung für Licht- Materie-Wechselwirkung konkurrieren um Anerkennung und eine ständige Optimierung der Systemparameter findet statt. Das Konzept von Mikrotürmchen scheint prädestiniert, da es viele anwendungsfreundliche Eigenschaften in sich vereint. Allerdings stellt die drastische Abnahme des Q Faktors für kleiner werdende Durchmesser d einen wesentlichen Limitierungsfaktor dieser Strukturen dar. Für viele Anwendungen resultiert daraus ein Kompromiss aus hohem Q Faktor und kleinem Modenvolumen der Strukturen, wodurch das volle Potential des Resonatorsystems nicht ausgeschöpft werden kann. Ziel dieser Arbeit war es, die drastische Abnahme des Q Faktors von Mikrotürmchen mit Durchmessern um 1μm aufzuheben und dadurch Resonatoren mit d < 1μm für ausgeprägte Licht-Materie-Wechselwirkung herzustellen. Dazu wurde erstmalig beabsichtigt eine Modenanpassung in Mikrotürmchen vorgenommen. Mittels Molekularstrahlepitaxie konnte eine Übergangsregion, bestehend aus drei Segmenten, in diese Strukturen implementiert und so ein adiabatischer Modenübergang zwischen der aktiven Mittelschicht und den Spiegelbereichen vorgenommen werden. Der positive Einfluss dadurch ergab sich in einer signifikanten Verbesserung des gemessenen Q Faktors für Durchmesser unter 1μm. Für d = 0.85μm konnte ein Q Faktor von 14 400 bestimmt werden. Dies stellt damit den höchsten je gemessenen Wert für Mikrotürmchen im Submikrometerbereich dar. Dadurch wird ein Bereich mit Modenvolumina < 3 kubischen Wellenlängen erschlossen und ausgeprägte Wechselwirkungseffekte im Mikrotürmchensystem sind zu erwarten. Starke Quantenpunkt-Licht-Kopplung konnte in diesen Strukturen nachgewiesen werden. Die höchste Vakuum-Rabiaufspaltung betrug 85μeV und die Visibilität wurde zu 0.41 bestimmt. Im Zuge der weiteren Optimierung der Systemparameter für die starke Kopplung wurde ein ex-situ Ausheilschritt auf die verwendete Quantenpunktsorte angewendet. In magnetooptischen Untersuchungen konnte damit eine Verdopplung der mittleren Oszillatorstärke auf einen Wert von 12 abgeschätzt werden. Weiter konnte in adiabatischen Mikrotürmchen über einen großen Durchmesserbereich von 2.25 bis 0.95μm eindeutiger Laserbetrieb des Quantenpunktensembles nachgewiesen werden. Dabei konnte eine kontinuierliche Reduzierung der Laserschwelle von über zwei Größenordnungen für kleiner werdende Durchmesser beobachtet werden. Für Durchmesser � < 1.6μm betrug der Beta-Faktor der Mikrolaser in etwa 0.5. Sie zeigten damit beinahe schwellenloses Verhalten. Zuletzt wurde der elektrische Betrieb von adiabatischen Mikrotürmchen gezeigt. Dafür wurde eine dotierte Struktur mit adiabatischem Design hergestellt. Im Vergleich zur undotierten Struktur fielen die gemessenen Q Faktoren in etwa um 5 000 geringer aus. Die spektralen Eigenschaften sowohl des Resonators als auch einzelner Quantenpunktlinien zeigten vernachlässigbare Abhängigkeit der Anregungsart (optisch oder elektrisch) und zeugen von einem erfolgreichen Konzept zum elektrischen Betrieb der Bauteile. Zeitaufgelöste Messungen erlaubten die Beobachtung von interessanten Dynamiken der Rekombination von Ladungsträgern in den Proben. Als Ursache dafür wurde ein hohes intrinsisches Feld, welches auf Grund des Designs der Schichtstruktur entsteht, identifiziert. Weiter zeigte sich, dass sich das interne Feld durch Anregungsart und extern angelegte Spannungen manipulieren lässt. N2 - Various concepts for the realization of a proper environment for interaction of light and matter compete for recognition and a continous optimizing process takes place. The concept of micropillars seems to be predestinated as it unifies many helpful properties for daily use applications. To this day the drastic decrease of the Q factor for smaller diameters d has been a fundamental reason for the limitation of these structures. For many applications a trade-off between high Q factor and small mode volume has been neccessary, so that the full potential of the resonator system has not been exploited totally. The objective of this work was to compensate for the drastic decrease of the Q factor of micropillars with diameters around 1μm and to fabricate resonators with d < 1μm for pronounced interaction of light and matter. For this purpose for the first time an intended mode engineering has been exploited in micropillars. By means of molecular beam epitaxy an intersection region, consisting of three segments, has been implemented in these structures and so an adiabatic transition of the mode between the active midsection and the mirrorparts has been achieved. The positive influence has been proven by a significant improvement of the measured Q factor for diameters below 1μm. For d = 0.85μm a Q factor of 14 400 has been detected. This is the highest Q factor ever measured for microilllars in the submicron regime. By that a regime with mode volumes < 3 cubic wavelengths gets accessible and pronounced effects of interaction in the system of micropillars are expected. In these structures strong quantum dot - light coupling has been shown. The largest vacuum- Rabisplitting has been 85μeV and the visibility has been determined to 0.41. In the course of further optimization of the system parameters for the regime of strong coupling an ex-situ annealing step has been adopted to the used type of quantum dots. Magnetooptical analysis has shown a doubling of the oscillator strength and allowed an estimation for the value to 12. Furthermore in adiabatic micropillars, over a vast diameter range from 2.25 to 0.95μm, clear evidence for lasing of the quantum dot ensemble has been shown. Simultanously a continous decrease of the lasing threshold by more than two orders of magnitude for small diameters has been observed. For Diameters < 1.6μm the Beta-factor of the microlasers has been determined to be around 0.5. Therefore they showed almost thresholdless behavior. Finally electrical operation of adiabatic micropillars has been shown. For that a doped structure with the adiabatic design has been fabricated. In comparison with the undoped structure the measured Q factors drop to values around 5 000. The spectral properties of both the resonator and single quantum dot lines have shown negligible dependence on the form of excitation (optical or electrical), indicating that a successful concept for the electrical excitation of the devices has been established. Time resolved measurments have allowed to observe interesting dynamics of the recombination of charge carriers. We have identified the large intrinsic field, which arises because of the design of the layer structure, being the origin for this. Furthermore we have shown, that the internal field can be manipulated by the excitation scheme and the external applied voltage. KW - Molekularstrahlepitaxie KW - Quantenpunkt KW - Adiabatische Modenanpassung KW - adiabatic modetransission KW - Licht Materie Wechselwirkung KW - light matter coupling KW - Optoelektronik KW - Lithografie KW - Spektroskopie Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-127438 ER - TY - JOUR A1 - Szalay, Aladar A A1 - Weibel, Stephanie A1 - Hofmann, Elisabeth A1 - Basse-Luesebrink, Thomas Christian A1 - Donat, Ulrike A1 - Seubert, Carolin A1 - Adelfinger, Marion A1 - Gnamlin, Prisca A1 - Kober, Christina A1 - Frentzen, Alexa A1 - Gentschev, Ivaylo A1 - Jakob, Peter Michael T1 - Treatment of malignant effusion by oncolytic virotherapy in an experimental subcutaneous xenograft model of lung cancer JF - Journal of Translational Medicine N2 - Background Malignant pleural effusion (MPE) is associated with advanced stages of lung cancer and is mainly dependent on invasion of the pleura and expression of vascular endothelial growth factor (VEGF) by cancer cells. As MPE indicates an incurable disease with limited palliative treatment options and poor outcome, there is an urgent need for new and efficient treatment options. Methods In this study, we used subcutaneously generated PC14PE6 lung adenocarcinoma xenografts in athymic mice that developed subcutaneous malignant effusions (ME) which mimic pleural effusions of the orthotopic model. Using this approach monitoring of therapeutic intervention was facilitated by direct observation of subcutaneous ME formation without the need of sacrificing mice or special imaging equipment as in case of MPE. Further, we tested oncolytic virotherapy using Vaccinia virus as a novel treatment modality against ME in this subcutaneous PC14PE6 xenograft model of advanced lung adenocarcinoma. Results We demonstrated significant therapeutic efficacy of Vaccinia virus treatment of both advanced lung adenocarcinoma and tumor-associated ME. We attribute the efficacy to the virus-mediated reduction of tumor cell-derived VEGF levels in tumors, decreased invasion of tumor cells into the peritumoral tissue, and to viral infection of the blood vessel-invading tumor cells. Moreover, we showed that the use of oncolytic Vaccinia virus encoding for a single-chain antibody (scAb) against VEGF (GLAF-1) significantly enhanced mono-therapy of oncolytic treatment. Conclusions Here, we demonstrate for the first time that oncolytic virotherapy using tumor-specific Vaccinia virus represents a novel and promising treatment modality for therapy of ME associated with advanced lung cancer. KW - Oncolytic virotherapy KW - Malignant effusion KW - Lung cancer KW - VEGF KW - Lungenkrebs KW - Vascular endothelial Growth Factor Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-96016 UR - http://www.translational-medicine.com/content/11/1/106 ER - TY - JOUR A1 - Scholz, M. A1 - Sauer, C. A1 - Wiessner, M. A1 - Nguyen, N. A1 - Scholl, A. A1 - Reinert, F. T1 - Structure formation in organic thin films observed in real time by energy dispersive near-edge x-ray absorption fine-structure spectroscopy JF - New Journal of Physics N2 - We study the structure formation of 1,4,5,8-naphthalenetetracarboxylicacid- dianhydride (NTCDA) multilayer films on Ag(111) surfaces by energy dispersive near-edge x-ray absorption fine-structure spectroscopy (NEXAFS) and photoelectron spectroscopy. The time resolution of seconds of the method allows us to identify several sub-processes, which occur during the post-growth three-dimensional structural ordering, as well as their characteristic time scales. After deposition at low temperature the NTCDA molecules are preferentially flat lying and the films exhibit no long-range order. Upon annealing the molecules flip into an upright orientation followed by an aggregation in a transient phase which exists for several minutes. Finally, threedimensional islands are established with bulk-crystalline structure involving substantial mass transport on the surface and morphological roughening. By applying the Kolmogorov–Johnson–Mehl–Avrami model the activation energies of the temperature-driven sub-processes can be derived from the time evolution of the NEXAFS signal. KW - physics Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-129749 VL - 15 IS - 083052 ER - TY - THES A1 - Bollmann, Stefan T1 - Structural Dynamics of Oligopeptides determined by Fluorescence Quenching of Organic Dyes T1 - Bestimmung struktureller Dynamiken von Oligopeptiden mittels Fluoreszenzlöschung von organischen Fluorophoren N2 - For determination of structures and structural dynamics of proteins organic fluorophores are a standard instrument. Intra- and intermolecular contact of biomolecular structures are determined in time-resolved and stationary fluorescence microscopy experiments by quenching of organic fluorophores due to Photoinduced Electron Transfer (PET) and dimerization interactions. Using PET we show in this work that end-to-end contact dynamics of serine-glycine peptides are slowed down by glycosylation. This slow down is due to a change in reaction enthalpy for end-to-end contact and is partly compensated by entropic effects. In a second step we test how dimerization of MR121 fluorophore pairs reports on end-to-end contact dynamics. We show that in aqueous solutions containing strong denaturants MR121 dimerization reports advantageously on contact dynamics for glycine-serine oligopeptides compared to the previously used MR121/tryptophane PET reporters. Then we analyze dimer interactions and quenching properties of different commercially available fluorophores being standards in Förster Resonance Energy Transfer (FRET) measurements. Distances in biomolecules are determinable using FRET, but for very flexible biomolecules the analysis of masurement data can be distorted if contact of the two FRET fluorophores is likely. We quantify how strong the quenching of fluorophore pairs with two different or two identical fluorophores is. Dimer spectra and association constants are quantified to estimate if fluophores are applicable in various applications, e.g. in FRET measurements with unstructured peptides and proteins. N2 - Zur Charakterisierung von Proteinen werden in der fluoreszenzbasierten Mikroskopie organische Farbstoffe benutzt, um strukturelle Informationen bzw. Informationen über dynamische Prozesse zu gewinnen. In der zeitaufgelösten und stationären Fluoreszenzmikroskopie können hiermit Kontaktprozesse durch photoinduzierten Elektronentransfer und auch Dimerisierung der Fluorophore analysiert werden. In dieser Arbeit wird mittels photoinduziertem Elektronentransfer PET gezeigt, dass Glykosylierung End-zu-End Kontaktkinetiken verändert. Sehr flexible Serin-Glycin Peptide zeigen glykosyliert langsamere Kinetiken durch Veränderung der Reaktionsenthalpie der Kontaktreaktion beider Peptidenden verglichen zu unglykosylierten. Diese enthalpischen Beiträge werden zum Teil von entropischen Beiträgen kompensiert. Außerdem wird gezeigt, dass Glycin-Serin Peptiddynamiken auch mittels Farbstoffpaaren gemessen werden können, die auf Löschwechselwirkungen durch Dimerisierung beruhen. Die Stärke dieser Löschwechselwirkungen hängt vom Farbstoffpaar ab. In Lösungen mit Denaturierungsmitteln können Farbstoffpaare des Fluoreszenzfarbstoffes MR121 vorteilhaft für Messungen von Dynamiken von Glycin-Serin Peptiden genutzt werden. Die Dimerwechselwirkungen können bei sehr flexiblen Biomolekülen und möglichem Kontakt von Fluorophoren die konventionelle Analyse von Förster Resonanz Energie Transfer (FRET) Messungen erschweren. Wir untersuchen an Glycin-Serin Oligopeptiden das Dimerisierungsverhalten kommerziell erhältlicher Fluorophore, die in FRET Messungen verwendet werden. Für gleiche und verschiedene Fluorophore wird die Löschung durch Dimerwechselwirkungen quantifiziert. Dabei werden Dimerspektren und Assoziationskonstanten für Dimerisierungsreaktionen bestimmt. Letztere helfen bei der Abschätzung, ob Fluorophorpaare für verschiedene Anwendungen geeignet sind, zum Beispiel in FRET-Messungen in unstrukturierten Peptiden und Proteinen. KW - Fluorophore KW - Fluoreszenzlöschung KW - h-dimerization KW - Lumineszenzlöschung KW - Fluoreszenzkorrelationsspektroskopie KW - Glykosylierung KW - Dimerisierung Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-92191 ER - TY - JOUR A1 - Moffet, R. C. A1 - Rödel, R. C. A1 - Kelly, S. T. A1 - Yu, X. Y. A1 - Carroll, G. T. A1 - Fast, J. A1 - Zaveri, R. A. A1 - Laskin, A. A1 - Gilles, M. K. T1 - Spectro-microscopic measurements of carbonaceous aerosol aging in Central California JF - Atmospheric Chemistry and Physics N2 - Carbonaceous aerosols are responsible for large uncertainties in climate models, degraded visibility, and adverse health effects. The Carbonaceous Aerosols and Radiative Effects Study (CARES) was designed to study carbonaceous aerosols in the natural environment of the Central Valley, California, and learn more about their atmospheric formation and aging. This paper presents results from spectro-microscopic measurements of carbonaceous particles collected during CARES at the time of a pollution accumulation event (27-29 June 2010), when in situ measurements indicated an increase in the organic carbon content of aerosols as the Sacramento urban plume aged. Computer-controlled scanning electron microscopy coupled with an energy dispersive X-ray detector (CCSEM/EDX) and scanning transmission X-ray microscopy coupled with near-edge X-ray absorption spectroscopy (STXM/NEXAFS) were used to probe the chemical composition and morphology of individual particles. It was found that the mass of organic carbon on individual particles increased through condensation of secondary organic aerosol. STXM/NEXAFS indicated that the number fraction of homogenous organic particles lacking inorganic inclusions (greater than similar to 50 nm equivalent circular diameter) increased with plume age, as did the organic mass per particle. Comparison of the CARES spectro-microscopic dataset with a similar dataset obtained in Mexico City during the MILAGRO campaign showed that fresh particles in Mexico City contained three times as much carbon as those sampled during CARES. The number fraction of soot particles at the Mexico City urban site (ranging from 16.6 to 47.3 %) was larger than at the CARES urban site (13.4-15.7%), and the most aged samples from CARES contained fewer carbon-carbon double bonds. Differences between carbonaceous particles in Mexico City and California result from different sources, photochemical conditions, gas phase reactants, and secondary organic aerosol precursors. The detailed results provided by these spectro-microscopic measurements will allow for a comprehensive evaluation of aerosol process models used in climate research. KW - photochemical air-pollution KW - Mexico City KW - black carbon KW - mixing state KW - atmospheric aerosols Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-121827 SN - 1680-7324 VL - 13 IS - 20 ER - TY - JOUR A1 - König, Markus A1 - Baenninger, Matthias A1 - Garcia, Andrei G. F. A1 - Harjee, Nahid A1 - Pruitt, Beth L. A1 - Ames, C. A1 - Leubner, Philipp A1 - Brüne, Christoph A1 - Buhmann, Hartmut A1 - Molenkamp, Laurens W. A1 - Goldhaber-Gordon, David T1 - Spatially Resolved Study of Backscattering in the Quantum Spin Hall State JF - Physical Review X N2 - The discovery of the quantum spin Hall (QSH) state, and topological insulators in general, has sparked strong experimental efforts. Transport studies of the quantum spin Hall state have confirmed the presence of edge states, showed ballistic edge transport in micron-sized samples, and demonstrated the spin polarization of the helical edge states. While these experiments have confirmed the broad theoretical model, the properties of the QSH edge states have not yet been investigated on a local scale. Using scanning gate microscopy to perturb the QSH edge states on a submicron scale, we identify well-localized scattering sites which likely limit the expected nondissipative transport in the helical edge channels. In the micron-sized regions between the scattering sites, the edge states appear to propagate unperturbed, as expected for an ideal QSH system, and are found to be robust against weak induced potential fluctuations. KW - mesoscopics KW - topological insulators KW - transport KW - charge KW - wells KW - branched flow KW - nanostructures Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-127225 SN - 2160-3308 VL - 3 IS - 2 ER - TY - JOUR A1 - Astakhov, Georgy V. A1 - Fuchs, F. A1 - Soltamov, V. A. A1 - Väth, S. A1 - Baranov, P. G. A1 - Mokhov, E. N. A1 - Dyakonov, V. T1 - Silicon carbide light-emitting diode as a prospective room temperature source for single photons JF - Scientific Reports N2 - Generation of single photons has been demonstrated in several systems. However, none of them satisfies all the conditions, e.g. room temperature functionality, telecom wavelength operation, high efficiency, as required for practical applications. Here, we report the fabrication of light-emitting diodes (LEDs) based on intrinsic defects in silicon carbide (SiC). To fabricate our devices we used a standard semiconductor manufacturing technology in combination with high-energy electron irradiation. The room temperature electroluminescence (EL) of our LEDs reveals two strong emission bands in the visible and near infrared (NIR) spectral ranges, associated with two different intrinsic defects. As these defects can potentially be generated at a low or even single defect level, our approach can be used to realize electrically driven single photon source for quantum telecommunication and information processing. KW - semiconductors KW - inorganic LEDs KW - quantum optics KW - nanophotonics KW - plasmonics Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-96308 ER - TY - THES A1 - Pohl, Christoph T1 - Silicon Based MBE of Manganese-Silicide and Silicon-Suboxide T1 - Silizium basierte MBE von Mangansilizid und Siliziumsuboxid N2 - The present thesis deals with the fabrication, optimization of growth process and characterization of silicon based materials with molecular beam epitaxy. Two material systems are investigated in the course of this work: silicon/silicon suboxide multilayer structures and mono manganese silicide thin films. Mono manganese silicide (MnSi) is grown on Si(111) substrates with an hydrogen passivated surface, that is prepared by wet chemical processes. The growth start is performed by deposition of an amorphous Mn wetting layer that is subsequently annealed to form a MnSi seed layer on which the MnSi molecular beam epitaxy (MBE) is achieved. An amorphous or a crystalline Si cap layer is deposited onto the MnSi film to finalize the growth process and protect the sample from oxidation. With Raman spectroscopy it is shown that the crystalline cap layer is in fact single crystalline silicon. Results of x-ray diffraction and Raman spectroscopy confirm the growth of mono manganese silicide in contrast to other existing manganese silicide phases. In addition, in-plane and out-of-plane residual strain, and twinning of the MnSi thin film is detected with x-ray diffraction of symmetric and asymmetric reflections. Orientation between the Si substrate and the MnSi film is determined with the parallel lattice planes MnSi(210) and Si(511). Transport measurements show a T^2 dependence of the resistivity below 30K and metallic behavior above, a magneto resistance of 0.9% and an unusual memory like effect of the resistance for an in-plane magnetic field sweep measurement. Silicon/Silicon suboxide (SiOx) multilayer structures are grown on Si(100) by interrupting the Si growth and oxidizing the surface with molecular oxygen. During oxidation the RHEED pattern changes from the Si(2x1) reconstruction to an amorphous pattern. When silicon growth is resumed a spotty RHEED pattern emerges, indicating a rough, three dimensional surface. The rough surface can be smoothed out with Si growth at substrate temperatures between 600°C and 700°C. Measurements with transmission electron microscopy show that a silicon suboxide layer of about 1nm embedded in single crystalline silicon is formed with the procedure. Multilayer structures are achieved by repeating the oxidation procedure when the Si spacer layer has a smooth and flat surface. The oxygen content of the suboxide layers can be varied between 7.6% and 26.8%, as determined with secondary ion mass spectrometry and custom-built simulations models for the x-ray diffraction. Structural stability of the multilayer structures is investigated by x-ray diffraction before and after rapid thermal annealing. For temperatures up to 1000°C the multilayer structures show no modification of the SiOx layer in x-ray diffraction. N2 - Die vorgelegte Arbeit handelt von der Herstellung siliziumbasierter Materialien mittels Molekularstrahlepitaxie, der Charakterisierung der Proben und der Optimierung der Wachstumsprozesse. Zwei Materialsysteme werden in dieser Arbeit behandelt: Silizium/Siliziumsuboxid Vielschichtstrukturen und dünne Schichten Mono-Mangansilizid. Mono-Mangansilizid (MnSi) wird auf Wasserstoff passivierten Si(111)-Substraten gewachsen. Für den Wachstumsstart wird eine amorphe Schicht Mangan auf den Si-Wafer abgeschieden und anschließend getempert. Dieser Prozess erzeugt eine ultra dünne Schicht MnSi, die als Keimschicht für das Wachstum dient. Zum Abschluss des Wachstums wird die MnSi-Schicht mit einer amorphen oder einkristallinen Deckschicht vor dem Oxidieren an der Luft geschützt. Das einkristalline Überwachsen der MnSi-Schicht ist mittels Ramanspektroskopie bestätigt. Röntgendiffraktometrie und Ramanspektroskopie bestätigen, dass es sich bei der gewachsenen Schicht um MnSi handelt und nicht um die manganreiche oder siliziumreiche Phasen von Mangansilizid. Anhand der Röntgendiffraktometrie von symmetrischen und asymmetrischen Reflektionen wird die laterale und vertikale Restverspannung gemessen, zusätzlich wird die Entstehung von Zwillingen in der Schicht gezeigt. Die Orientierung der MnSi-Schicht relativ zum Si Substrat ist anhand der parallelen Netzebenen MnSi(210) und Si(511) bestimmt. Transportmessungen an den Schichten zeigen unterhalb von 30K eine T^2-Abhängigkeit des spezifischen Widerstands, oberhalb metallisches Verhalten. Der Magneto Widerstand der MnSi Schicht beträgt 0.9%. Bei einem Magnetfeldsweep in der Schichtebene wird ein kurioses, dem Memory-Effekt ähnliches Verhalten beobachtet. Silizium/Siliziumsuboxid (SiOx)-Vielschichtstrukturen werden auf Si(100) Substraten gewachsen. Das Siliziumwachstum wird unterbrochen und die Probenoberfläche mit molekularem Sauerstoff oxidiert. Dabei verändert sich das RHEED-Muster von der Si-(2x1) Rekonstruktion zu einem amorphen Muster. Das Siliziumwachstum wird nach der Oxidation fortgesetzt und im RHEED entsteht dabei ein Punktmuster das von einer rauen, drei-dimensionalen Oberfläche zeugt. Durch Siliziumwachstum bei Substrattemperaturen zwischen 600°C und 700°C wird die Oberfläche wieder geglättet. Aufnahmen mit dem Transmissionselektronenmikroskop zeigen, dass bei diesem Wachstum eine 1nm dicke SiOx-Schicht eingebettet zwischen einkristalline Siliziumschichten entsteht. Wenn die Siliziumoberfläche wieder glatt ist, kann durch wiederholen der Wachstumssequenz eine Vielschichtstruktur hergestellt werden. Der Sauerstoffgehalt der hergestellten Suboxidschichten wurde mittels Sekundärionen-Massenspektrometrie und eigens zu diesem Zweck angepassten Röntgendiffraktometrie-Simulationen auf 7.6% bis 26.8% bestimmt. Die strukturelle Stabilität der Proben wurde mit Röntgendiffraktometrie vor und nach kurzem Hochtemperaturtempern untersucht. Bei Temperaturen bis 1000°C kann mittels Röntgendiffraktometrie keine Änderung der Si/SiOx Vielschicht-Strukturen festgestellt werden. KW - Molekularstrahlepitaxie KW - Siliciumdioxid KW - Mangansilicide KW - Mangansilizid KW - Suboxid KW - Manganesesilicide KW - Siliconsuboxide KW - Silicium KW - Herstellung KW - Halbleiter KW - Mangan Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-83757 ER - TY - JOUR T1 - Search for WH production with a light Higgs boson decaying to prompt electron-jets in proton–proton collisions at \(\sqrt {s}=7\)  TeV with the ATLAS detector JF - New Journal of Physics N2 - A search is performed for WH production with a light Higgs boson decaying to hidden-sector particles resulting in clusters of collimated electrons, known as electron-jets. The search is performed with \(2.04 fb^{−1}\) of data collected in 2011 with the ATLAS detector at the Large Hadron Collider in proton–proton collisions at \(\sqrt {s}=7 TeV\) . One event satisfying the signal selection criteria is observed, which is consistent with the expected background rate. Limits on the product of the WH production cross section and the branching ratio of a Higgs boson decaying to prompt electron-jets are calculated as a function of a Higgs boson mass in the range from 100 to 140 GeV. KW - Higgs boson Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-131565 VL - 15 IS - 043009 ER - TY - JOUR T1 - Search for extra dimensions in diphoton events from proton–proton collisions at \(\sqrt {s} = 7\)  TeV in the ATLAS detector at the LHC JF - New Journal of Physics N2 - The large difference between the Planck scale and the electroweak scale, known as the hierarchy problem, is addressed in certain models through the postulate of extra spatial dimensions. A search for evidence of extra spatial dimensions in the diphoton channel has been performed using the full set of proton–proton collisions at \(\sqrt {s} = 7\) TeV recorded in 2011 with the ATLAS detector at the CERN Large Hadron Collider. This dataset corresponds to an integrated luminosity of \(4.9 fb^{−1}\). The diphoton invariant mass spectrum is observed to be in good agreement with the Standard Model expectation. In the context of the model proposed by Arkani–Hamed, Dimopoulos and Dvali, 95% confidence level lower limits of between 2.52 and 3.92 TeV are set on the ultraviolet cutoff scale MS depending on the number of extra dimensions and the theoretical formalism used. In the context of the Randall–Sundrum model, a lower limit of 2.06 (1.00) TeV at 95% confidence level is set on the mass of the lightest graviton for couplings of \(k/\overline {M}_{Pl} = 0.1 (0.01)\). Combining with the ATLAS dilepton searches based on the 2011 data, the 95% confidence level lower limit on the Randall–Sundrum graviton mass is further tightened to 2.23 (1.03) TeV for \(k/\overline {M}_{Pl} = 0.1 (0.01)\). KW - diphoton events KW - proton-proton collision Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-131548 VL - 15 ER - TY - JOUR T1 - Search for excited electrons and muons in \(\sqrt {s}=8\) TeV proton–proton collisions with the ATLAS detector JF - New Journal of Physics N2 - The ATLAS detector at the Large Hadron Collider is used to search for excited electrons and excited muons in the channel \(pp →ℓℓ^\ast→ℓℓ\gamma \), assuming that excited leptons are produced via contact interactions. The analysis is based on \(13 fb^{−1}\) of pp collisions at a centre-of-mass energy of 8 TeV. No evidence for excited leptons is found, and a limit is set at the 95% credibility level on the cross section times branching ratio as a function of the excitedlepton mass \(m_{ℓ^\ast}\) . For \(m_{ℓ^\ast}\) ≽0.8 TeV, the respective upper limits on \(\sigma B(ℓ→ ℓ\gamma)\) are 0.75 and 0.90 fb for the \(e^\ast\) and \(μ^\ast\) searches. Limits on \(\sigma B\) are converted into lower bounds on the compositeness scale \(\Lambda\). In the special case where \(\Lambda = m_{ℓ^\ast}\), excited-electron and excited-muon masses below 2.2 TeV are excluded. KW - excited electrons KW - muons Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-131557 VL - 15 IS - 093011 ER - TY - THES A1 - Förtig, Alexander T1 - Recombination Dynamics in Organic Solar Cells T1 - Rekombinationsdynamiken in organischen Solarzellen N2 - Neben herkömmlichen, konventionellen anorganischen Solarzellen — hauptsächlich auf Silizium basierend — ist die Organische Photovoltaik (OPV) auf dem besten Wege in naher Zukunft eine kostengünstige, umweltfreundliche, komplementäre Technolgie darzustellen. Die Produktionskosten, die Lebenszeit der Solarzellen sowie deren Wirkungsgrad müssen dabei weiter optimiert werden, um einen Markteintritt der OPV zu ermöglichen. Die vorliegende Arbeit befasst sich mit der Effizienz organischer Solarzellen und deren Limitierung durch die Rekombination von Ladungsträgern. Um funktionsfähige Zellen zu untersuchen, werden zeitaufgelöste Experimente wie die Messung der transienten Photospannung (TPV), des transienten Photostroms (TPC), die Ladungsextraktion (CE) sowie die time delayed collection field (TDCF) Methode angewandt. Untersucht werden sowohl flüssig prozessierte als auch aufgedampfte Proben, unterschiedliche Materialzusammensetzungen und verschiedene Probengeometrien. Das Standardmaterialsystem der OPV, P3HT:PC61BM, wird bei verschiedenen emperaturen und Beleuchtungsstärken auf die Lebenszeit und Dichte der photogenerierten Ladungsträger überprüft. Für den Fall spannungsunabhängiger Generation von Ladungsträgern zeigt sich die Anwendbarkeit der Shockley-Gleichung auf organische Solarzellen. Des Weiteren wird ein konsistentes Modell erläutert, welches den Idealtitätsfaktor direkt mit der Rekombination von freien mit gefangenen, exponentiell verteilten Ladungsträgern verknüpft. Ein Ansatz, bekannt unter der Bezeichung j=V Rekonstruktion, ermöglicht es, den leistungslimitierenden Verlustmechanismus in unbehandelten und thermisch geheizten P3HT:PC61BM Solarzellen zu identifizieren. Dieses Verf ahren, welches TPV, CE und TDCF Messungen beinhaltet, wird auf Proben basierend auf dem neuartigen, low-band gap Polymer PTB7 in Verbindung mit dem Fulleren PC71BM ausgeweitet. Während in der Zelle hergestellt aus reinem Chlorbenzol beträchtliche geminale wie nichtgeminale Verluste zu beobachten sind, erleichtert die Zugabe eines Lösungsmittelzusatzes die Polaronenpaartrennung, was zu einer starken Reduktion geminaler Verluste führt. In einer Kooperation mit dem IMEC Institut in Leuven, werden abschließend die beiden bedeutensten Probenarchitekturen organischer Solarzellen, die planare und die Mischübergang Struktur, jeweils basierend auf CuPC und C60, bezüglich nichtgeminaler Rekombination und Ladungsträgerverteilung miteinander verglichen. Neben den beiden experimentellen Techniken um TPV und CE werden makroskopische Simulationen herangezogen, um den Ursprung unterschiedlichen Voc vs. Lichtintensität–Verhaltens zu erklären. N2 - Besides established, conventional inorganic photovoltaics—mainly based on silicon—organic photovoltaics (OPV) are well on the way to represent a lowcost, environment friendly, complementary technology in near future. Production costs, solar cell lifetime and performance are the relevant factors which need to be optimized to enable a market launch of OPV. In this work, the efficiency of organic solar cells and their limitation due to charge carrier recombination are investigated. To analyze solar cells under operating conditions, time-resolved techniques such as transient photovoltage (TPV), transient photocurrent (TPC) and charge extraction (CE) are applied in combination with time delayed collection field (TDCF) measurements. Solution processed and evaporated samples of different material composition and varying device architectures are studied. The standard OPV reference system, P3HT:PC61BM, is analyzed for various temperatures in terms of charge carrier lifetime and charge carrier density for a range of illumination intensities. The applicability of the Shockley Equation for organic solar cells is validated in case of field-independent charge photogeneration. In addition, a consistent model is presented, directly relating the ideality factor to the recombination of free with trapped charge carriers in an exponential density of states. An approach known as j=V reconstruction enables to identify the performance limiting loss mechanism of as-prepared and thermally treated P3HT:PC61BM solar cells. This procedure, involving TPV, CE and TDCF measurements, is extended to samples based on the rather new, low-band gap polymer PTB7 in combination with PC71BM. While in the devices processed from pure chlorobenzene solution considerable geminate and nongeminate losses are observed, the use of a solvent additive facilitates efficient polaron pair dissociation minimizing geminate recombination. Finally, in collaboration with the IMEC institute in Leuven, the two main organic solar cell device architectures, planar and bulk heterojunction—both based on CuPc and C60—are directly compared in terms of nongeminate recombination and charge carrier distribution. Two experimental techniques, TPV and CE, as well as a macroscopic device simulation are applied to reveal the origin of different Voc vs. light intensity dependence. KW - Organische Solarzelle KW - Fotovoltaik KW - Organischer Halbleiter KW - physics KW - solar cell KW - recombination KW - organic semiconductors KW - Physik KW - Solartechnik KW - Energietechnik KW - Solarzelle KW - Rekombination Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-83895 ER - TY - THES A1 - Joseph, Arun Antony T1 - Real-time MRI of Moving Spins Using Undersampled Radial FLASH T1 - Echtzeit MRI von bewegten Spins mithilfe der unterabgetasteten radialen FLASH sequenz N2 - Nuclear spins in motion is an intrinsic component of any dynamic process when studied using magnetic resonance imaging (MRI). Moving spins define many functional characteristics of the human body such as diffusion, perfusion and blood flow. Quantitative MRI of moving spins can provide valuable information about the human physiology or of a technical system. In particular, phase-contrast MRI, which is based on two images with and without a flow-encoding gradient, has emerged as an important diagnostic tool in medicine to quantify human blood flow. Unfortunately, however, its clinical usage is hampered by long acquisition times which only provide mean data averaged across multiple cardiac cycles and therefore preclude Monitoring the immediate physiological responses to stress or exercise. These limitations are expected to be overcome by real-time imaging which constitutes a primary aim of this thesis. Short image acquisition times, as the core for real-time phase-contrast MRI, can be mainly realized through undersampling of the acquired data. Therefore the development focused on related technical aspects such as pulse sequence design, k-space encoding schemes and image reconstruction. A radial encoding scheme was experimentally found to be robust to motion and less sensitive to undersampling than Cartesian encoding. Radial encoding was combined with a FLASH acquisition technique for building an efficient real-time phase-contrast MRI sequence. The sequence was further optimized through overlapping of gradients to achieve the shortest possible echo time. Regularized nonlinear inverse reconstruction (NLINV), a technique which jointly estimates the image content and its corresponding coil sensitivities, was used for image reconstruction. NLINV was adapted specifically for phase-contrast MRI to produce both Magnitude images and phase-contrast maps. Real-time phase-contrast MRI therefore combined two highly undersampled (up to a factor of 30) radial gradient-echo acquisitions with and without a flow-encoding gradient with modified NLINV reconstructions. The developed method achieved real-time phase-contrast MRI at both high spatial (1.3 mm) and temporal resolution (40 ms). Applications to healthy human subjects as well as preliminary studies of patients demonstrated real-time phase-contrast MRI to offer improved patient compliance (e.g., free breathing) and immediate access to physiological variations of flow parameters (e.g., response to enhanced intrathoracic pressure). In most cases, quantitative blood flow was measured in the ascending aorta as an important blood vessel of the cardiovascular circulation system commonly studied in the clinic. The performance of real-time phase-contrast MRI was validated in comparison to standard Cine phase-contrast MRI using studies of flow phantoms as well as under in vivo conditions. The evaluations confirmed good agreement for comparable results. As a further extension to real-time phase-contrast MRI, this thesis implemented and explored a dual-echo phase-contrast MRI method which employs two sequential gradient echoes with and without flow encoding. The introduction of a flow-encoding gradient in between the two echoes aids in the further reduction of acquisition time. Although this technique was efficient under in vitro conditions, in vivo studies showed the influence of additional motion-induced Phase contributions. Due to these additional temporal phase information, the approach showed Little promise for quantitative flow MRI. As a further method three-dimensional real-time phase-contrast MRI was developed in this thesis to visualize and quantify multi-directional flow at about twice the measuring time of the standard real-time MRI method, i.e. at about 100 ms temporal resolution. This was achieved through velocity mapping along all three physical gradient directions. Although the method is still too slow to adequately cover cardiovascular blood flow, the preliminary results were found to be promising for future applications in tissues and organ systems outside the heart. Finally, future developments are expected to benefit from the adaptation of model-based reconstruction techniques to real-time phase-contrast MRI. N2 - Die Bewegung der Kernspins ist eine wesentliche Eigenschaft von dynamischen Vorgängen, die mit Hilfe der Magnetresonanztomographie (MRT) untersucht werden. Bewegte oder fließende Spins charakterisieren viele Funktionen des menschlichen Körpers, wie z.B. die Gewebeperfusion und den Blutfluss in den Gefäßen. Die quantitative MRT von bewegten Spins kann daher wertvolle Informationen über die menschliche Physiologie oder auch über ein technisches System geben. Insbesondere die Phasenkontrast-MRT, die auf der Aufnahme von zwei Bildern mit und ohne flusskodierenden Gradienten basiert, hat sich als ein wichtiges diagnostisches Werkzeug in der Medizin entwickelt, um den Blutfluss funktionell zu quantifizieren. Die klinische Nutzung ist jedoch durch die langen Messzeiten eingeschränkt, da die Daten über mehrere Herzzyklen gemittelt werden müssen und damit die Untersuchung unmittelbarer physiologischer Reaktionen auf Stress und/oder Muskelbelastung ausgeschlossen ist. Ein primäres Ziel dieser Arbeit war es, diese Einschränkungen durch die Entwicklung einer MRT-Flussmessung in Echtzeit zu überwinden. Entscheidende Grundlage jeder Echtzeit-MRT sind kurze Aufnahmezeiten, die vor allem durch eine Reduktion der aufgenommenen Daten (Unterabtastung) realisiert werden. Daher konzentrierte sich die hier vorgestellte Entwicklung auf die damit verbundenen technischen Aspekte wie die MRT-Sequenz zur Datenaufnahme, das räumliche Kodierungsschema, und die Bildrekonstruktion. Experimentell erwies sich ein radiales Kodierungsschema als robust gegenüber Bewegungen und relativ unempfindlich gegenüber milder Unterabtastung. Dieses Kodierungsschema wurde mit der FLASH Aufnahmetechnik für eine effiziente Phasenkontrast-Sequenz in Echtzeit kombiniert. Zusätzlich wurde die Sequenz durch Überlappung von Gradienten hinsichtlich einer kurzen Echozeit optimiert. Für die Bildrekonstruktion wurde die regularisierte nichtlineare inverse Rekonstruktion (NLINV) verwendet, bei der die Bildinformation und die entsprechenden pulensensitivitäten gleichzeitig geschätzt werden. NLINV wurde speziell für die Phasenkontrast-MRT angepasst, um sowohl Betragsbilder als auch robuste Phasenkontrast-Karten mit hoher raumzeitlicher Genauigkeit zu berechnen. Das erarbeitete Verfahren der Phasenkontrast-MRT in Echtzeit kombiniert daher zwei stark unterabgetastete (bis zu einem Faktor von 30) und unterschiedlich flusskodierte, radiale Gradientenecho-Aufnahmen mit einer modifizierten NLINV Rekonstruktion. Mit dieser Methode wurde sowohl eine gute räumliche Auflösung (1.3 mm), als auch eine hohe zeitliche Auflösung (40 ms) erreicht. Bei Anwendungen an gesunden Probanden sowie vorläufigen Untersuchungen von Patienten konnte nachgewiesen werden, dass die Phasenkontrast-MRT in Echtzeit einen verbesserten Komfort für die Patienten (z.B. freie Atmung) und unmittelbaren Zugang zu physiologischen Veränderungen der Flussparameter bietet (z.B. Reaktion auf erhöhten Druck im Brustraum). In den meisten Fällen wurden quantitative Blutflussmessungen in der aufsteigenden Aorta, einem klinisch wichtigen Gefäß des Herz-Kreislauf-Systems, vorgenommen. Die Messungen mit der Phasenkontrast-MRT in Echtzeit wurden mit der EKG-getriggerten Cine Phasenkontrast-MRT (klinischer Standard) an einem Flussphantom und unter in vivo Bedingungen verglichen. Die Ergebnisse zeigten unter vergleichbaren Bedingungen gute Übereinstimmung. Im Rahmen dieser Arbeit wurde zusätzlich eine Doppelecho-Variante der Phasenkontrast-MRT in Echtzeit implementiert. Das Einfügen eines flusskodierenden Gradienten zwischen den beiden Echos führte zu einer weiteren Reduzierung der Messzeit. Obwohl sich diese Technik unter in vitro Bedingungen als tauglich erwies, zeigten sich bei in vivo Studien störende Einflüsse durch bewegungsinduzierte Phasenbeiträge, die wenig Erfolg für quantitative Flussmessungen versprechen. Als weitere Methode wurde in dieser Arbeit eine dreifach kodierte Sequenz zur Phasenkontrast-MRT entwickelt, um multidirektionalen Fluss zu untersuchen. Die Geschwindigkeitskodierung entlang aller drei physikalischen Gradientenrichtungen führte zu einer verlängerten Messzeit (zeitliche Auflösung � 100 ms) gegenüber der Echtzeit-Flussmessung in nur einer Richtung. Obwohl das Verfahren noch zu langsam ist, um den kardiovaskulären Blutfluss adäquat zu beschreiben, waren vorläufige Ergebnisse in Körperregionen außerhalb des Herzens für zukünftige klinische Anwendungen sehr vielversprechend. Es ist zu erwarten, dass entsprechende Weiterentwicklungen von modellbasierten ekonstruktionsverfahren profitieren werden. KW - Kernspintomografie KW - Real-time MRI Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-94000 ER - TY - THES A1 - Ruff, Andreas T1 - On the importance of electronic correlations in potassium-doped organic semiconductors T1 - Über die Bedeutung elektronischer Korrelationen in Kalium-dotierten organischen Halbleitern N2 - The present thesis is concerned with the impact of alkali metal-doping on the electronic structure of semiconducting organic thin films. The organic molecular systems which have been studied are the polycyclic aromatic hydrocarbons picene, pentacene, and coronene. Motivated by reports about exceptional behavior like superconductivity and electronic correlations of their alkali metal-doped compounds, high quality films fabricated from the above named molecules have been studied. The electronic structure of the pristine materials and their doped compounds has been investigated using photoelectron spectroscopy. Core level and valence band studies of undoped films yield excellent photoemission spectra agreeing with or even outperforming previously reported data from the literature. Alkali metal-doping manifests itself in a uniform manner in the electronic structure for all probed samples: Opposed to reports from the literature about metallicity and even superconductivity in alkali metal-doped picene, pentacene, and coronene, all films exhibit insulating nature with an energy gap of the order of one electron-volt. Remarkably, this is independent of the doping concentration and the type of dopant, i.e., potassium, cesium, or sodium. Based on the interplay between narrow bandwidths in organic semiconductors and sufficiently high on-molecule Coulomb repulsion, the non-metallicity is attributed to the strong influence of electronic correlations leading to the formation of a Mott insulator. In the case of picene, this is consolidated by calculations using a combination of density functional theory and dynamical mean-field theory. Beyond the extensive considerations regarding electronic correlations, further intriguing aspects have been observed. The deposition of thin picene films leads to the formation of a non-equilibrium situation between substrate and film surface. Here, the establishment of a homogeneous chemical potential is hampered due to the only weak van der Waals-interactions between the molecular layers in the films. Consequently, spectral weight is measurable above the reference chemical potential in photoemission. Furthermore, it has been found that the acceptance of additional electrons in pentacene is limited. While picene and coronene are able to host up to three extra electrons, in pentacene the limit is already reached for one electron. Finally, further extrinsic effects, coming along with alkali metal-doping, have been scrutinized. The oxidation of potassium atoms induced by the reaction with molecular oxygen in the residual gas of the ultra-high vacuum system turned out to significantly influence the electronic structure of alkali metal-doped picene and coronene. Moreover, also the applied X-ray and UV irradiation caused a certain impact on the photoemission spectra. Surprisingly, both effects did not play a role in the studies of potassium-doped pentacene. N2 - Die vorliegende Arbeit beschäftigt sich mit der Dotierung organischer Dünnfilme mittels Alkalimetall-Interkalation sowie deren Einfluss auf die elektronische Struktur der Filme. Untersucht wurden zu diesem Zweck die polyzyklischen aromatischen Kohlenwasserstoffe Picen, Pentacen und Coronen. Berichte über außerordentliche Eigenschaften wie Supraleitung und elektronische Korrelationen in Alkalimetall-dotierten Verbindungen der genannten organischen Halbleiter liefern die Motivation für diese Arbeit. Die elektronische Struktur sowohl der reinen Filme als auch ihrer dotierten Verbindungen wurde unter Verwendung von Photoelektronenspektroskopie untersucht. Rumpfniveau- und Valenzband-Spektren der reinen Filme spiegeln deren hohe Qualität wider. Die Dotierung mit Alkalimetallen äußert sich für die drei untersuchten Probensysteme auf eine überraschend einheitliche Art und Weise in der elektronischen Struktur: In Diskrepanz zu Berichten aus der Literatur über Metallizität oder gar Supraleitung in Alkalimetall-dotiertem Picen, Pentacen und Coronen zeigen alle Filme isolierendes Verhalten mit einer Energielücke in der Größenordnung von einem Elektronenvolt. Dieses Verhalten tritt unabhängig von der Dotierkonzentration und der Art des Donators (Kalium, Cäsium oder Natrium) auf. Basierend auf dem Zusammenspiel schmaler Bandbreiten in organischen Halbleitern und hoher Coulomb-Abstoßung der Elektronen auf den Molekülen wird die beobachtete Nicht-Metallizität dem starken Einfluss elektronischer Korrelationen zugeschrieben. Im Fall von Picen wird diese Annahme durch theoretische Betrachtungen bekräftigt, wobei Rechnungen im Rahmen einer Kombination aus Dichtefunktionaltheorie und dynamischer Molekularfeldtheorie durchgeführt wurden. Neben den Ausführungen hinsichtlich elektronischer Korrelationen werden in dieser Arbeit weitere interessante Beobachtungen adressiert. So hat das Wachstum dünner Picen-Filme die Entstehung eines Nicht-Gleichgewichts zwischen Substrat und Filmoberfläche zur Folge: Auf Grund der nur schwachen van der Waals-Wechselwirkung zwischen den Moleküllagen der Filme wird die Ausbildung eines homogenen chemischen Potentials erschwert. Dies führt zu der unerwarteten Beobachtung von spektralem Gewicht oberhalb des chemischen Potentials des Referenzsystems. Des Weiteren konnte gefunden werden, dass die Akzeptanz zusätzlicher Elektronen in Pentacen limitiert ist. Während Picen und Coronen in der Lage sind, bis zu drei weitere Elektronen aufzunehmen, ist die entsprechende Grenze bei Pentacen schon für ein Elektron erreicht. Abschließend wurden weitere extrinsische Effekte aufgeklärt, die im Zusammenhang mit der Alkalimetall-Dotierung auftraten. Zum einen führt die Reaktion von Kalium-Atomen mit molekularem Sauerstoff im Restgas der Ultrahochvakuum-Apparatur zur Bildung von Kaliumoxid. Dies äußert sich deutlich in der elektronischen Struktur von Alkalimetall-dotiertem Picen und Coronen. Des Weiteren zeigte hier die verwendete Röntgen- sowie UV-Strahlung deutliche Auswirkungen auf die Photoemissionsspektren. Beide Effekte spielten im Fall der Studien an Pentacen keine Rolle. KW - Organischer Halbleiter KW - Dotierung KW - Kalium KW - Elektronische Korrelationen KW - organic semiconductors KW - photoemission KW - electronic correlations KW - Elektronenkorrelation KW - Kondensierte Materie KW - Halbleiter KW - Photoelektronenspektroskopie Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-83635 ER - TY - THES A1 - Wagenpfahl, Alexander Johannes T1 - Numerical simulations on limitations and optimization strategies of organic solar cells T1 - Numerische Simulationen von Limitierungen und Optimierungsstrategien organischer Solarzellen N2 - Continuously increasing energy prices have considerably influenced the cost of living over the last decades. At the same time increasingly extreme weather conditions, drought-filled summers as well as autumns and winters with heavier rainfall and worsening storms have been reported. These are possibly the harbingers of the expected approaching global climate change. Considering the depletability of fossil energy sources and a rising distrust in nuclear power, investigations into new and innovative renewable energy sources are necessary to prepare for the coming future. In addition to wind, hydro and biomass technologies, electricity generated by the direct conversion of incident sunlight is one of the most promising approaches. Since the syntheses and detailed studies of organic semiconducting polymers and fullerenes were intensified, a new kind of solar cell fabrication became conceivable. In addition to classical vacuum deposition techniques, organic cells were now also able to be processed from a solution, even on flexible substrates like plastic, fabric or paper. An organic solar cell represents a complex electrical device influenced for instance by light interference for charge carrier generation. Also charge carrier recombination and transport mechanisms are important to its performance. In accordance to Coulomb interaction, this results in a specific distribution of the charge carriers and the electric field, which finally yield the measured current-voltage characteristics. Changes of certain parameters result in a complex response in the investigated device due to interactions between the physical processes. Consequently, it is necessary to find a way to generally predict the response of such a device to temperature changes for example. In this work, a numerical, one-dimensional simulation has been developed based on the drift-diffusion equations for electrons, holes and excitons. The generation and recombination rates of the single species are defined according to a detailed balance approach. The Coulomb interaction between the single charge carriers is considered through the Poisson equation. An analytically non-solvable differential equation system is consequently set-up. With numerical approaches, valid solutions describing the macroscopic processes in organic solar cells can be found. An additional optical simulation is used to determine the spatially resolved charge carrier generation rates due to interference. Concepts regarding organic semiconductors and solar cells are introduced in the first part of this work. All chapters are based on previous ones and logically outline the basic physics, device architectures, models of charge carrier generation and recombination as well as the mathematic and numerical approaches to obtain valid simulation results. In the second part, the simulation is used to elaborate issues of current interest in organic solar cell research. This includes a basic understanding of how the open circuit voltage is generated and which processes limit its value. S-shaped current-voltage characteristics are explained assigning finite surface recombination velocities at metal electrodes piling-up local space charges. The power conversion efficiency is identified as a trade-off between charge carrier accumulation and charge extraction. This leads to an optimum of the power conversion efficiency at moderate to high charge carrier mobilities. Differences between recombination rates determined by different interpretations of identical experimental results are assigned to a spatially inhomogeneous recombination, relevant for almost all low mobility semiconductor devices. N2 - Stetig steigende Preise für Energie haben die Lebenshaltungskosten in Deutschland über die letzten Jahrzehnte maßgeblich beeinflusst. Gleichzeitig werden scheinbar extremere Wetterbedingungen, dürrere Sommer, ebenso wie regen und sturmreichere Winter aufgezeichnet. Dies könnten bereits heute die Vorboten eines kommenden, globalen Klimawandels sein. Berücksichtigt man die Endlichkeit fossiler Energieträger und die wachsende Ablehnung gegenüber nuklearer Energieerzeugung, führt kein Weg an einer genaueren Erforschung innovativer, erneuerbarer Energiequellen vorbei. Neben Wind- und Wasserkraft stellt die direkte Umwandlung von Sonnenlicht in elektrischen Strom einen der erfolgversprechendsten Ansätze dar. Seit Beginn der Synthese und der genaueren Untersuchungen organischer, halbleitender Polymere und Fullerene innerhalb der letzten Jahre, wurde eine neue Arte der Solarzellenherstellung, neben den bereits etablierten Technologien, denkbar. Zusätzlich zu klassischen Aufdampfverfahren können Solarzellen aus organischen Materialien in Lösung hergestellt und auf verschiedenartigste Materialien wie Plastik, Stoff oder Papier aufgebracht werden. Aufgrund der Unordnung in den aktiven Schichten verhalten sich solche Solarzellen jedoch anders als solche aus anorganischen Materialien. Eine organische Solarzelle ist ein komplexes elektrisches Bauteil, welches durch eine Anzahl physikalischer Effekte maßgeblich beeinflusst wird. So ist, beispielsweise, die Verteilung erzeugter Ladungsträger durch optische Interferenzeffekte bestimmt. Ladungstransport und Ladungsträgerrekombination stellen weitere Einflussfaktoren dar. Die experimentell gemessenen Strom-Spannungs-Kennlinien sind somit stets makroskopische Kombination mehrerer Effekte. Änderungen einzelner Parameter führen zu einer komplexen Änderung des elektrischen Verhaltens des Bauteils. Folgerichtig ist es notwendig, ein Modell zu entwickeln, welches das Verhalten organischer Solarzellen bei sich ändernden Umgebungsbedingungen, allgemeingültig vorhersagen kann. Im Rahmen dieser Arbeit wurde, zu diesem Zweck, eine eindimensionale, numerische Simulation entwickelt. Basierend auf Drift- und Diffusionsgleichungen für Elektronen, Löcher und Exzitonen kann der Ladungstransport in organischen Halbleitern beschrieben werden. Benötigte Generations- und Rekombinationsraten werden durch entsprechende Ratengleichungen bestimmt. Über die Poisson-Gleichung wird zudem das auftretende elektrische Feld innerhalb der Solarzelle berücksichtigt. Das resultierende differentielle Gleichungssystem ist jedoch nicht analytisch lösbar. Nur mit Hilfe spezieller numerischer Methoden, können gültige Lösungen gefunden werden. Hiermit kann das Verhalten organischer Solarzellen sehr gut beschrieben. Eine zusätzliche optische Simulation kann dazu benutzt werden, optische Interferenzeffekte zu berücksichtigen. Im des ersten Teiles dieser Arbeit werden Methoden und Modellvorstellungen für Prozesse in organischer Solarzellen vorgestellt. Die Kapitel bauen aufeinander auf und gehen nacheinander auf die grundlegende Physik, die Bauteilarchitektur, die Modelle der Ladungsträgergeneration und -rekombination, ebenso wie auf die benötigten mathematischen und numerischen Methoden ein. Beiträge zur aktuellen Forschung werden im zweiten Abschnitt vorgestellt. Diese Umfassen ein grundlegendes Verständnis der offenen Klemmspannung organischer Solarzellen. Diese wird entweder durch Oberflächenrekombination an den Elektroden oder durch Injektionsbarrieren limitiert. S-förmige Verformungen von gemessenen und simulierten Strom-Spannungs-Kennlinien konnten durch endliche Oberflächenrekombinationsgeschwindigkeiten erklärt werden. Aufgrund verminderter Extraktions- und Injektionseigenschaften entsteht eine spannungsabhängige Raumladungszone, welche diese oft beobachtete Verformung verursacht. Der Wirkungsgrad organischer Solarzellen konnte als Kompromiss zwischen Ladungsträgeranhäufung und -extraktion im Bauteil identifiziert werden. Dies führt letztendlich zu einem Optimum der Solarzelleneffizienz bei moderaten bis hohen Ladungsträgerbeweglichkeiten. Abweichungen experimentell unterschiedlich bestimmter Rekombinationsraten konnten auf eine räumlich inhomogene Verteilung der Ladungsträgerrekombination zurückgeführt werden. Diese wird durch selektive Kontakte erzeugt und ist für alle halbleitenden Bauelemente mit niedriger Mobilität relevant. KW - Organische Solarzelle KW - Fotovoltaik KW - Organischer Halbleiter KW - s-shape KW - Doppeldiode KW - Simulation KW - Solarzelle KW - Rekombination KW - Strom-Spannungs-Kennlinie Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-90119 N1 - zu ergänzende PACS-Nummern wären: 88.40.jr und 81.05.Fb (Quelle: http://www.aip.org/publishing/pacs/pacs-alphabetical-index) ER - TY - JOUR A1 - Dasenbrook, Elliot C. A1 - Lu, Luan A1 - Donnola, Shannon A1 - Weaver, David E. A1 - Gulani, Viskas A1 - Jakob, Peter M. A1 - Konstan, Michael W. A1 - Flask, Chris A. T1 - Normalized T1 Magnetic Resonance Imaging for Assessment of Regional Lung Function in Adult Cystic Fibrosis Patients - A Cross-Sectional Study JF - PLOS ONE N2 - Background: Cystic fibrosis (CF) patients would benefit from a safe and effective tool to detect early-stage, regional lung disease to allow for early intervention. Magnetic Resonance Imaging (MRI) is a safe, non-invasive procedure capable of providing quantitative assessments of disease without ionizing radiation. We developed a rapid normalized T1 MRI technique to detect regional lung disease in early-stage CF patients. Materials and Methods: Conventional multislice, pulmonary T1 relaxation time maps were obtained for 10 adult CF patients with normal spirometry and 5 healthy non-CF control subjects using a rapid Look-Locker MRI acquisition (5 seconds/imaging slice). Each lung absolute T1 map was separated into six regions of interest (ROI) by manually selecting upper, central, and lower lung regions in the left and right lungs. In order to reduce the effects of subject-to-subject variation, normalized T1 maps were calculated by dividing each pixel in the absolute T1 maps by the mean T1 time in the central lung region. The primary outcome was the differences in mean normalized T1 values in the upper lung regions between CF patients with normal spirometry and healthy volunteers. Results: Normalized T1 (nT1) maps showed visibly reduced subject-to-subject variation in comparison to conventional absolute T1 maps for healthy volunteers. An ROI analysis showed that the variation in the nT1 values in all regions was <= 2% of the mean. The primary outcome, the mean (SD) of the normalized T1 values in the upper right lung regions, was significantly lower in the CF subjects [.914 (.037)] compared to the upper right lung regions of the healthy subjects [.983 (.003)] [difference of .069 (95% confidence interval .032-.105); p=.001). Similar results were seen in the upper left lung region. Conclusion: Rapid normalized T1 MRI relaxometry obtained in 5 seconds/imaging slice may be used to detect regional early-stage lung disease in CF patients. KW - infants KW - disease KW - ventilation KW - infection KW - guidelines KW - diagnosis KW - children Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-128346 SN - 1932-6203 VL - 8 IS - 9 ER - TY - JOUR A1 - Hopfmann, C. A1 - Albert, F. A1 - Schneider, C. A1 - Höfling, S. A1 - Kamp, M. A1 - Forchel, A. A1 - Kanter, I. A1 - Reizenstein, S. T1 - Nonlinear emission characteristics of quantum dot-micropillar lasers in the presence of polarized optical feedback JF - New Journal of Physics N2 - We report on electrically pumped quantum dot-microlasers in the presence of polarized self-feedback. The high-\(\beta\) microlasers show two orthogonal, linearly polarized emission modes which are coupled via the common gain medium. This coupling is explained in terms of gain competition between the two lasing modes and leads to distinct differences in their input-output characteristics. By applying polarized self-feedback via an external mirror, we are able to control the laser characteristics of the emission modes in terms of the output power, the coherence time and the photon statistics. We find that linearly polarized self-feedback stabilizes the lasing of a given mode, while cross-polarized feedback between the two modes reduces strongly the intensity of the other emission mode showing particular high-intensity fluctuations and even super-thermal values of the photon autocorrelation function \(g^{(2)} (\tau)\) at zero delay. Measurements of \(g^{(2)} (\tau)\) under external feedback also allow us to detect revival peaks associated with the round trip time of the external cavity. Analyzing the damping and shape of the \(g^{(2)} (\tau)\) revival peaks by a phenomenological model provides us insight into the underlying physics such as the effective exciton lifetime and gain characteristics of the quantum dots in the active region of these microlasers. KW - semiconductor lasers KW - coherence KW - system KW - gain Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-123127 SN - 1367-2630 VL - 15 IS - 025030 ER - TY - THES A1 - Baerwald, Philipp T1 - Neutrinos from gamma-ray bursts, and the multi-messenger connection T1 - Neutrinos von Gammablitzen und die Verbindung zu multiplen Botenteilchen N2 - In this work, we take a look at the connection of gamma-ray bursts (GRBs) and ultra-high-energy cosmic rays (UHECR) as well as the possibilities how to verify this connection. The currently most promising approach is based on the detection of high-energy neutrinos, which are associated with the acceleration of cosmic rays. We detail how the prompt gamma-ray emission is connected to the prediction of a neutrino signal. We focus on the interactions of photons and protons in this regard. At the example of the current ANTARES GRB neutrino analysis, we show the differences between numerical predictions and older analytical methods. Moreover, we discuss the possibilities how cosmic ray particles can escape from GRBs, assuming that UHECR are entirely made up of protons. For this, we compare the commonly assumed neutron escape model with a new component of direct proton escape. Additionally, we will show that the different components, which contribute to the cosmic ray flux, strongly depend on the burst parameters, and test the applicability on some chosen GRBs. In a further step, we continue with the considerations regarding the connection of GRBs and UHECR by connecting the GRB source model with the cosmic ray observations using a simple cosmic ray propagation code. We test if it is possible to achieve the observed cosmic ray energy densities with our simple model and what the consequences are regarding the prompt GRB neutrino flux predictions as well as the cosmogenic neutrinos. Furthermore, we consider the question of neutrino lifetime and how it affects the prompt GRB neutrino flux predictions. In a final chapter, we show that it is possible to apply the basic source model with photohadronic interactions to other types of sources, using the example of the microquasar Cygnus X-3. N2 - In dieser Arbeit beschäftigen wir uns mit dem Zusammenhang von Gammablitzen (GRBs) und ultra-hochenergetischer kosmischer Strahlung (UHECR) sowie mit den Möglichkeiten, wie dieser Zusammenhang überprüft werden kann. Der zur Zeit erfolgsversprechendste Ansatz basiert auf der Detektion von hochenergetischen Neutrinos, die mit der Beschleunigung von kosmischer Strahlung assoziiert werden. Wir zeigen detailliert, wie die prompte Emission im Bereich der Gammastrahlung mit der Voraussage eines Neutrinosignals zusammenhängt. Ein besonderes Augenmerk legen wir hierbei auf die Wechselwirkung von Photonen und Protonen. Am Beispiel der aktuellen Analyse des ANTARES Neutrinoteleskops zu Neutrinos von Gammablitzen zeigen wir, wie sich numerische Voraussagen von älteren analytischen Methoden unterscheiden. Des Weiteren diskutieren wir Möglichkeiten, wie die Teilchen der kosmischen Strahlung aus einem Gammablitz entkommen können, wenn die ultra-hochenergetische kosmische Strahlung nur aus Protonen bestehen würde. Wir vergleichen dazu das meistens angenommene Entkommen in Form von Neutronen mit einer neuen Komponente von direkt ausströmenden Protonen. Auch zeigen wir, dass die unterschiedlichen Komponenten, die zur kosmischen Strahlung beitragen, stark von den verwendeten Parametern der Gammablitze abhängen, und uberprüfen die Modelle an einigen ausgewählten Gammablitzen. In einem weiteren Schritt führen wir die Überlegungen zu dem Zusammenhang von Gammablitzen und ultra-hochenergetischer kosmischer Strahlung fort, in dem wir mittels eines einfachen Propagationscodes für kosmische Strahlung eine Verbindung zwischen dem Quellmodell für Gammablitze und den Beobachtungsdaten der kosmischen Strahlung herstellen. Wir überprüfen, inwieweit sich die beobachteten Energiedichten der kosmischen Strahlung mittels unseres einfachen Modells realisieren lassen und welche Konsequenzen dies für die Voraussagen der prompten Neutrinoemission von Gammablitzen sowie den kosmogenischen Neutrinos hat. Außerdem gehen wir der Frage nach, wie die vorausgesagten prompten Neutrinoflüsse von einer endlichen Lebenszeit der Neutrinos beeinflusst werden würden. In einem letzten Kapitel übertragen wir das verwendete grundlegende Quellmodell mit photohadronischen Wechselwirkungen auf eine andere Klasse von Quellen, am Beispiel von Voraussagen fürden Mikroquasar Cygnus X-3. KW - Neutrino KW - Gamma-Burst KW - neutrinos KW - gamma-ray bursts KW - cosmic rays KW - multi-messenger physics KW - Gammablitze KW - Kosmische Strahlung KW - multiple Botenteilchen KW - UHECR KW - Burst Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-85333 ER - TY - THES A1 - Schmitt, Peter T1 - MR imaging of tumors: Approaches for functional and fast morphological characterization T1 - MR-Bildgebung von Tumoren: Ansätze zur funktionellen und schnellen morphologischen Charakterisierung N2 - The subject of this work was to develop, implement, optimize and apply methods for quantitative MR imaging of tumors. In the context of functional and physiological characterization, this implied transferring techniques established in tumor model research to human subjects and assessing their feasibility for use in patients. In the context of the morphologic assessment and parameter imaging of tumors, novel concepts and techniques were developed, which facilitated the simultaneous quantification of multiple MR parameters, the generation of “synthetic” MR images with various contrasts, and the fast single-shot acquisition of purely T2-weighted images. N2 - Gegenstand dieser Arbeit war die Entwicklung, Implementierung, Optimierung und Anwendung von Methoden für die quantitative MR-Bildgebung an Tumoren. In Bezug auf eine funktionelle und physiologische Charakterisierung wurden in der Forschung an Tumormodellen etablierte Verfahren für den Einsatz am Menschen adaptiert und ihre Anwendbarkeit zur Untersuchung von Tumoren wurde an Patienten erforscht. Im Bereich der morphologischen Untersuchung und Parameterbildgebung an Tumoren wurden neue Konzepte und Verfahren entwickelt, welche die simultane Quantifizierung mehrerer MR-Parameter, die Generierung "synthetischer" MR-Bilder mit unterschiedlichen Kontrasten, sowie die schnelle "Single-Shot"-Akquisition rein T2-gewichteter Bilder ermöglichen. KW - Kernspintomografie KW - Tumor KW - MR imaging KW - Tumors KW - Relaxometry KW - IR-TrueFISP KW - synthetic MRI KW - TOSSI Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-135967 ER - TY - THES A1 - Michalska, Marta T1 - Molecular Imaging of atherosclerosis T1 - Molekulare Bildgebung der Atherosklerose N2 - Atherosklerose ist eine aktive und progressive Erkrankung, bei der vaskuläre Adhäsionsmoleküle wie VCAM-1 eine entscheidende Rolle durch Steuerung der Rekrutierung von Immunzellen in den frühen und fortgeschrittenen Plaques spielen. Ein zielgerichteter Einsatz von VCAM-1-Molekülen mit spezifischen Kontrastmitteln ist daher eine Möglichkeit, die VCAM-1-Expression zu kontrollieren, Plaquewachstum ab einem frühen Zeitpunkt zu visualisieren und eine frühe Prävention von Atherosklerose vor Beginn der Thrombusbildung zu etablieren. Des Weiteren bietet die nichtinvasive Magnetresonanz (MR)-Bildgebung den Vorteil der Kombination molekularer und morphologischer Daten. Sie ermöglicht, mithilfe von entwickelten VCAM-1-markierten Eisenoxidpartikeln, den spezifischen Nachweis entzündlicher Prozesse während der Atherosklerose. Diese Arbeit belegt, dass mit dem VCAM-1-Konzept eine vielversprechende Herangehensweise gefunden wurde und dass das, mit spezifischen superparamagnetischen Eisenoxid (USPIO) konjugierte VCAM-1-Peptid, gegenüber unspezifischer USPIOs ein erhöhtes Potenzial bei der Untersuchung der Atherosklerose in sich trägt. Im ersten Teil der Arbeit konnte im Mausmodell gezeigt werden, dass gerade das VCAM-1-Molekül ein sinnvoller Ansatzpunkt zur Darstellung und Bildgebung von Atherosklerose ist, da in der frühen Phase der Entzündung die vaskulären Zelladhäsionsmoleküle überexprimiert und auch kontinuierlich, während der fortschreitenden Plaquebildung, hochreguliert werden. Weiterhin beschreibt diese Arbeit die Funktionstüchtigkeit und das Vermögen des neu gestalteten USPIO Kontrastmittels mit dem zyklischen Peptid, in seiner Spezialisierung auf die VCAM-1 Erkennung. Experimentelle Studien mit ultra-Hochfeld-MRT ermöglichten weitere ex vivo und in vivo Nachweise der eingesetzten USPIO-VCAM-1-Partikel innerhalb der Region um die Aortenwurzel in frühen und fortgeschrittenen atherosklerotischen Plaques von 12 und 30 Wochen alten Apolipoprotein E-defizienten (ApoE-/-) Mäusen. Mit ihrer Kombination aus Histologie und Elektronenmikroskopie zeigt diese Studie zum ersten Mal die Verteilung von VCAM-1-markierten USPIO Partikeln nicht nur in luminalem Bereich der Plaques, sondern auch in tieferen Bereichen der medialen Muskelzellen. Dieser spezifische und sensitive Nachweis der frühen und fortgeschrittenen Stadien der Plaquebildung bringt auf molekularer Ebene neue Möglichkeiten zur Früherkennung von atherosklerotischen Plaques vor dem Entstehen von 8 Rupturen. Im Gegensatz zum USPIO-VCAM-1-Kontrastmittel scheiterten unspezifische USPIO Partikel an der Identifikation früher Plaqueformen und begrenzten die Visualisierung von Atherosklerose auf fortgeschrittene Stadien in ApoE-/- Mäusen. N2 - Atherosclerosis is an active and progressive condition where the vascular cell adhesion molecules as VCAM-1 play a vital role controlling the recruitment of immune cells within the early and advanced plaques. Therefore targeting of VCAM-1 molecules with specific contrast agent bears the possibility to monitor the VCAM-1 expression, visualize the plaque progression starting at the early alterations, and help to establish early prevention of atherosclerosis before the origin of the thrombus formation, of which late recognition leads to myocardial infarction. Furthermore noninvasive magnetic resonance imaging (MRI) offers the benefit of combining the molecular and anatomic data and would thus enable specific detection of VCAM-1 targeted iron oxide contrast agent within inflammatory process of atherosclerosis. This thesis exactly presents the VCAM-1 concept as a suitable molecular approach and the potential of specific ultrasmall superparamagnetic iron oxide (USPIO) conjugated to the VCAM-1 binding peptide over unspecific non-targeted USPIO particles for evaluation of atherosclerosis. This work firstly demonstrated that selection of VCAM-1 molecules offers a good and potential strategy for imaging of atherosclerosis, as these vascular cell adhesion molecules are highly expressed in the early phase of inflammation and also continuously up-regulated within the advanced plaques. Secondly, this thesis showed the proof of principle and capability of the newly designed USPIO contrast agent conjugated to the specific cyclic peptide for VCAM-1 recognition. The experimental studies including ultra-high field MRI enabled further ex vivo and in vivo detection of applied USPIO-VCAM-1 particles within the aortic root region of early and advanced atherosclerotic plaques of 12 and 30 week old apolipoprotein E deficient (ApoE-/-) mice. Using a combination of histology and electron microscopy, this study for the first time pointed to distribution of targeted USPIO-VCAM-1 particles within plaque cells expressing VCAM-1 not only in luminal regions but also in deeper medial smooth muscle cell areas. Hence functionalized USPIO particles targeting VCAM-1 molecules allow specific and sensitive detection of early and advanced plaques at the molecular level, giving the new possibilities for early recognition of atherosclerotic plaques before the appearance of advanced and prone to rupture lesions. In contrast to the functionalized USPIO-VCAM-1, utilized non-targeted USPIO particles did not succeed in early plaque 6 identification limiting visualization of atherosclerosis to advanced forms in atherosclerotic ApoE-/- mice. KW - VCAM KW - Arteriosklerose KW - Superparamagnetische Eisenoxid Kontrastmittel KW - vaskuläre Adhäsionsmoleküle KW - Atherosklerose KW - superparamagnetische Eisenoxid Kontrastmittel KW - vascular cell adhesion molecules KW - atherosclerosis KW - iron oxide contrast agent KW - Kontrastmittel Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-73243 ER -