TY - THES A1 - Dutschke, Anke T1 - Charakterisierung von PZT-Dünnschichten auf Metallsubstraten T1 - Characterization of PZT Thin Films on Metal Substrates N2 - Das Mischkristallsystem PbZrxTi1-xO3 (PZT) gehört durch seine ausgeprägten piezo- und ferroelektrischen Eigenschaften zu den meist verwendeten Funktionskeramiken. In Form von Dünnschichten auf flexiblen Metallsubstraten können sie für unterschiedlichste Anwendungen als Tastschalter, Vibrationsdämpfer, Mikroaktuator oder Ultraschallwandler eingesetzt werden. Ziel der vorliegenden Arbeit ist es, den Gefügeaufbau und den Phasenbestand von PZT-Schichten, die in einem mehrstufigen Sol-Gel-Prozeß auf Blechen der säure- und temperaturbeständigen Chrom-Nickel-Legierung Hastelloy abgeschieden worden sind, zu analysieren und mit ihren ferroelektrischen und die-lektrischen Eigenschaften zu korrelieren. Es wird nachgewiesen, daß das Gefüge gezielt mittels verschiedener Temperaturbehandlungen und unter-schiedlicher Neodymdotierung variiert werden kann. Durch Nd-Dotierung wird das Maximum der Keimbil-dungsrate zu niedrigeren Temperaturen hin verschoben und die Wachstumsgeschwindigkeit gegenüber undotierten Schichten verringert. Die Kristallisation in dotierten und undotierten Schichten ist heterogen und erfolgt bevorzugt an den Grenz- und Oberflächen sowie an den Porenrändern im Innern der Schichten. Die Zusammensetzung der PZT-Sol-Gel-Beschichtungen liegt im Bereich der morphotropen Phasengrenze (x=0,53) zwischen tetragonaler und rhomboedrischer Phase. Erstmals wurde die während der Temperatur-behandlung auftretende Gradientenbildung im Zr/Ti-Verhältnis systematisch mit dem Gefüge und dem Phasenbestand auf Nanometerskala in Verbindung gesetzt. Hierbei konnte aufgezeigt werden, dass langreichweitige Zr:Ti-Fluktuationen vorrangig während der Kri-stallisation der Pyrochlorphase entstehen. Bei der nachfolgenden Perowskitkristallisation wachsen die Kri-stalle über die entmischten Bereiche hinweg, so daß Schwankungen im Zr:Ti-Verhältnis innerhalb der Kristallite erhalten bleiben. Es wird dargelegt, daß die Fluktuationen im Zr:Ti-Verhältnis infolge der starken Spannungen innerhalb der Schicht nur geringe Auswirkungen auf den Verzerrungsgrad der Kristallite und die Zugehörigkeit zur rhomboedrischen oder tetragonalen Perowskitphase haben. Beim Übergang in den ferroelektrischen Zustand ist das Ausmaß der Gitterverzerrung unabhängig von der Kristallitgröße und in Nd-dotierten Schichten generell geringer als in undotierten Schichten. Es wird die Ausbildung einer Zwischenschicht zwischen Metallsubstrat und PZT-Schicht untersucht, die die resultierenden elektrischen Eigenschaften maßgeblich beeinflußt. Sie wird als Oxidschicht identifiziert, be-stehend aus kristallinem NiO und NiCr2O4, verschiedenen Chromoxiden und Pb2(CrO4)O, die als nicht-ferroelektrisches Dielektrikum die resultierende Dielektrizitätskonstante des Substrat-Schichtverbundes stark herabsetzt. Durch Aufbringen einer unterstöchiometrischen La0,75Sr0,2MnO3 (ULSM) - Elektrodierung vor der PZT-Beschichtung gelingt es, die Kontaktierung zu verbessern, die (001)-Orientierung in undotierten Schichten zu steigern und sehr schmale P-E-Hysteresekurven zu erhalten. N2 - Lead zirconate titanate (PbZrxTi1-xO3 , PZT) is one of the most applied ceramic materials because of its dis-tinctive piezo- and ferroelectric properties. Prepared as thin films on flexible, metallic substrates it can be used for various applications as strain gauges, key switches, vibration dampers, microactuators and ultrasonic transducers. The aim of this work is to analyze the microstructure and the phase-content of PZT-thin films deposited on temperature- und acid-resistant hastelloy-sheets, to correlate the results with the ferroelectric and dielectric properties. It is demonstrated, that the specific variation of the microstructure can be achieved by different thermal treatments and the selective addition of Neodymium as dopant. Nd-doping leads to a shift of the maxi-mum nucleation rate towards reduced temperatures and a decrease in the rate of growth compared to undoped films. The PZT-films are prepared by a sol-gel-process in fourfold multilayers with a composition near the mor-photropic phase boundary, where the tetragonal und rhombohedral perovskite-phases coexist. The crystal-lisation in Nd-doped and undoped films takes place heterogeneously, preferentially at the interfaces and on the surface of the multilayered films as well as on the inner surface of pores within the films. For the first time, the Zr:Ti fluctuation phenomena emerging in sol-gel derived PZT films is related to the microstructure and the local phase content on a nanometer scale. In this connection it is proved, that long-distance Zr:Ti gradients arise preferentially before and during the crystallisation of the pyrochlore phase. During the following crystallisation of the perovskite phase, the crystallites grow across these gradients without modifying them. It is pointed out that the fluctuation in the Zr:Ti ratio has only minor influence on the amount of the tetragonal or rhombohedral distortion of the crystallites after the transition from the para- to the ferroelec-tric state due to strong stresses within the films. The magnitude of the lattice distortion is independent of the crystallite size and its extent is generally smaller for crystallites in Nd-doped films than for such in undoped films. After the detailed analysis of the development of the boundary layer between metal subtrate and PZT-film, it is identified as a non-ferroelectric, dielectric buffer-layer containing crystalline NiO und NrCr2O4, different chromiumoxides and Pb2(CrO4)O between the PZT film and the conductive substrate significantly dimini-shing the resulting dielectric properties of the system. By applying a non-stoichiometric La0,75Sr0,2MnO3 (ULSM) – electrode below the PZT-film, a better electrical contact is achieved, the (001)-orientation in undoped films is enhanced and narrow P-E-hysteresis loops can be obtained. KW - PZT KW - Dünne Schicht KW - Durchstrahlungselektronenmikroskopie KW - Sol-Gel-Verfahren KW - Mikrostruktur KW - Ferroelektrizität KW - Phasenanalyse KW - PZT KW - thin films KW - microstructure KW - ferroelectricity KW - sol-gel process Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-26235 ER - TY - THES A1 - Mallak, Matthias T1 - Beschichtung planarer Substrate durch Flüssigphasenabscheidung von Titandioxid T1 - Liquid Phase Deposition of titanium dioxide for coating of planar substrates N2 - Es wurden planare Substrate mittels Flüssigphasenabscheidung mit Titandioxid beschichtet. Durch Absorption von Polyelektrolyten konnte die chemische Beschaffenheit der Substratoberfläche so verändert werden, daß die verwendbaren Substratmaterialien zur Beschichtung mit dem LPD-Verfahren um Glas, Polycarbonat, PET und Polyethylen erweitert wurden. Bedeutung kommt besonders der LPD-Beschichtung auf Borosilicatglas zu, da damit erstmalig ein Vergleich zwischen TiO2-Schichten aus der Flüssigphasenabscheidung und Schichten, die mittels Sol-Gel-Verfahren gewonnen wurden, möglich wurde. Der systematische Vergleich zwischen den Schichten der beiden Beschichtungsverfahren, ergab, daß Sol-Gel-Beschichtungen eine thermische Nachbehandlung mit Temperaturen größer 400°C benötigen, um ihre optimalen optischen und mechanischen Eigenschaften zu erreichen. Dabei tritt zwar eine starke Schrumpfung durch die Pyrolyse organischer Reste und Kristallisation auf. Jedoch führt diese Schrumpfung zu keiner Rißbildung oder Delaminierung. Im Gegenteil, die Ausbildung eines anorganischen Netzwerkes führt zum Aushärten der Schicht. Die bei höheren Temperaturen auftretende Kristallisation ermöglicht einen höheren Brechungsindex der Schicht bei gleichbleibend sehr guter Transparenz. Die bereits teilkristallin abgeschiedenen TiO2-Filme aus dem LPD-Verfahren schrumpfen zwar weit weniger stark als die Sol-Gel-Schichten, durch eine schlechte Haftung auf der Glasoberfläche verbreitern sich jedoch bereits vorhandene schmale Risse. Die Pyrolyse des Polyelektrolytlayers führt zum Verlust der haftvermittelnden Schicht und damit zu einem drastischen Rückgang der Schichthaftung und daraus bedingend der Bleistifthärte. Die Rißbildung verursacht einen starken Anstieg der Schichttrübung. Weiterhin verursacht die Rißverbreitung bei steigender Temperatur einen geringeren Brechzahlanstieg, als dies das LPD-Material ermöglichen würde. Durch diese Ergebnisse wird offensichtlich, daß für Substrate, die hohe Temperaturen ermöglichen, Sol-Gel-Beschichtungen dem LPD-Verfahren vorzuziehen ist. Für thermisch nicht belastbare Substrate stellt die Flüssigphasenabscheidung jedoch ein sehr gutes Beschichtungsverfahren dar. Um bestmögliche Ergebnisse mit dem LPD-Verfahren zu erzielen, kommt der Modifizierung der Substratoberfläche eine entscheiden Bedeutung zu. Zur bereits bekannten Oberflächenmodifizierung durch Ätzen mit Natriumperoxodisulfat (Hydroxylierung) wurde hierbei die zusätzliche bzw. alleinige Funktionalisierung durch Adsorption eines Polyelektrolytbilayers untersucht. Durch die Verwendung eines Polyelektrolytbilayers konnte die Dichte an Kristallisationsstellen im Vergleich zum unbehandelten bzw. hydroxylierten Substrat erhöht werden. Dies führte im Einklang mit dem bekannten Schichtwachstummodell zu gleichmäßigeren Beschichtungen. Der Einsatz des Polyelektrolytbilayers konnte in allen Fällen dazu genutzt werden, die Trübung der Schicht zu verringern. Dabei wurden Trübungswerte größer 50 % meist auf Werte von ca. 20 % und kleiner verbessert. Hohe Keimdichten bewirken dabei eine geringe Trübung. Jedoch konnte auch bei geringeren Keimdichten durch den Polyelektrolytbilayer geringe Trübungswerte erreicht werden. Bei der mechanischen Charakterisierung der TiO2-Schichten konnte festgestellt werden, daß bei den polymeren Substraten durch Hydroxylierung oder den Polyelektrolytbilayer die Schichthaftung verbessert werden. Eine Abhängigkeit der mechanischen Schichteigenschaften von der Substrathärt konnte mit Ausnahme des sehr weichen Polyethylens nicht gefunden werden. Jedoch ist für eine hohe Bleistifthärte eine gute Haftung nötig. Abriebuntersuchungen mit einem Filzstempel (Crockmetertest) zeigten ein analoges Verhalten zum Bleistifthärtetest. Um eventuell auftretende Nachteile der weichen Polymere ausgleichen zu können, wurden parallel Polystyrolsubstrate, beschichtet mit einer ORMOCER®-Hartschicht, untersucht. Dabei wurden sehr gute Ergebnisse in Hinblick auf Keimstellendichte, optische und mechanische Eigenschaften erzielt. N2 - Planar substrates were coated with titanium dioxide by liquid phase deposition. The chemical properties of substrate surface were changed through adsorption of polyelectrolytes, so that coating of glass, polycarbonate, PET and polyethylene with the LPD process could be done. Especially the LPD-Coating on borofloatglass is of importance. For the first time, a comparison between coatings from liquid phase deposition and coatings from sol-gel process became possible. The systematic comparison between the films of the two coating processes showed that sol-gel coatings need a thermal treatment at temperature above 400 °C to unfold their optimal optical and mechanical properties. Thereby a high shrinkage caused by pyrolysis of organic residues and crystrallisation occurs. But that shrinkage does not lead to formation of cracks or delamination. In Contrast, the formation of a inorganic backbone leads to a hardening of the film. At higher temperature emerging crystallisation enables a higher refractive index with constant very good transparency. The partially crystalline films from the LPD-process shrink much less than the sol-gel films. But caused by a bad adhesion on the glass surface small cracks get broadened. Pyrolysis of polyelectrolytes leads to a loss of the bonding agent and associated with that to dramatic decrease in adhesion and pencil hardness. The formation of cracks causes an high increase in the haze of the film. The broadening of cracks at rising temperature avoids a higher increase in refractive index as could be possible from the LPD-material properties. These results reveal that for substrates tolerating high temperatures sol-gel-coating is preferable to the LPD-process. For thermal non-stable substrates the liquid phase deposition is a very suitable coating technique. To achieve best possible results with the LPD-Process, the modification of the substrate surface is of importance. Beside the already known surface modification through etching with sodium peroxodisulfate (hydroxylation) the additional or exclusive surfacemodification through of adsorption a polyelectrolytebilayer was investigated. By the application of a polyelectrolytebilayer the density of nucleation sites could be increased in comparison with the untreated or hydroxylated substrate. This leads in consistence with the known film formation model to more homogeneous coatings. In general the application of the polyelectrolytebilayer reduced the haze of the film. In most cases the haze was decreased from 50 % and higher to 20% and lower. High densities of nucleation sites effect a low haze. But using the polyelectrolytebilayer low haze could also achieved despite a low nuclei density. Based on the mechanical characterisation of the TiO2-films could be demonstrated that on polymeric substrates the adhesion increases if hydroxylation or polyelctrolytebilayers are used. A dependence of mechanical film properties on the hardness of the substrate could not be detected with the exception of the very soft polyethylene. For a high pencil hardness a high adhesion is the crucial factor . Abrasion test with a felt die (Crockmeter)showed an analogue behaviour as the pencil hardness test. To compensate potential disadvantages from the soft polymers, polystyrene substrates with a ORMOCER®-hardcover-film were examined. Films on these substrates showed very good results refering to the density of nucleation sites, optical and mechanical properties. KW - Anorganische Beschichtung KW - Beschichtung KW - Titandioxid KW - Polystyrol KW - Kunststoff KW - Biomimetik KW - Polyelektrolyt KW - Oberflächenfunktionalisierung KW - Layer-by-Layer-Verfahren KW - surface modification KW - layer-by-layer-process Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-25008 ER - TY - THES A1 - Mayer, Christian T1 - Alternative Keimbildner für transparente, farblose LAS-Glaskeramiken T1 - Nucleating agents for transparent, colorless LAS-glass ceramics N2 - In LAS-Glaskeramiken, die besondere Verbreitung bei Anwendungen als Kochfläche, Brandschutzglas und Bauteil für präzise Optik gefunden haben, werden vorrangig die Keimbildner TiO2 und ZrO2 eingesetzt. Transparente Glaskeramiken weisen jedoch eine mehr oder weniger starke Gelbfärbung auf, die vorrangig aus dem Einsatz von TiO2 zusammen mit unvermeidbaren Fe2O3-Verunreinigungen resultiert. Die Minimierung dieser Gelbfärbung gewinnt zunehmend an Bedeutung. Ziel der vorliegenden Arbeit ist die Prüfung, inwiefern die Verringerung der Eigenfarbe einer transparenten LAS-Glaskeramik durch Ersatz des färbenden Keimbildners TiO2 durch einen weniger färbenden Keimbildner möglich ist, ohne dass das gute Keimbildungsvermögen beeinträchtigt wird. Verschiedene alternative Keimbildner zu TiO2 wurden stets in Kombination mit ZrO2 hinsichtlich Keimbildungsvermögen und Färbung/Transmission untersucht sowie andere Kerneigenschaften im Vergleich zu der Standardkeimbildnerkombination TiO2/ZrO2 diskutiert. Signifikante Vorteile bzgl. Eigenfarbe und Transmission gegenüber dem TiO2/ZrO2-gekeimten Referenzmaterial konnten nur bei der Keimbildnerkombination SnO2/ZrO2 gefunden werden. Die Transmission ist mit 89% statt 87% beim Referenzmaterial höher, die Eigenfarbe ist mit dem Farbort a*/b* = -0,1/+2,3 deutlich näher am Unbuntpunkt als die Referenz a*/b* = -0,6/+5,1, der Yellowness Index reduziert sich von 9,5 auf 4,6. N2 - LAS-glass ceramics, which are widely-used as cooktop panels, fire protection glasses and precise optical devices, are commonly doped with TiO2 and ZrO2 as nucleating agents. Transparent glass ceramics show a more or less intense yellow coloring, which is mainly caused by the use of TiO2 together with unavoidable Fe2O3 contamination. The reduction of yellowness becomes more important. Object of the dissertation is the investigation, whether the yellowness could be reduced by substitution of the coloring TiO2 by a less coloring nucleating agent. Thereby, the nucleating power should be maintained. Several alternative nucleating agents have been tested regarding the nucleating power, coloring/transmission as well as other key properties. The second nucleating agent ZrO2 remained basically unchanged. The results have been compared with the commonly used nucleating agents TiO2 and ZrO2. Significant advantages concerning coloring and transmission have exclusively been found with the combination of SnO2 and ZrO2. The transmission of 89% is higher than reference of 87% and the coloring is definitely lower (a*/b* = -0.1/+2.3 instead of a*/b* = -0.6/+5.1), the yellowness index could be reduced from 9.5 down to 4.6. KW - Glaskeramik KW - Keimbildung KW - Glaskeramik KW - Keimbildner KW - glass ceramic KW - nucleating agents Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-19206 ER - TY - THES A1 - Bockmeyer, Matthias T1 - Structure and Densification of Thin Films Prepared From Soluble Precursor Powders by Sol-Gel Processing T1 - Struktur und Verdichtung von dünnen Schichten hergestellt über das Sol-Gel Verfahren unter Verwendung löslicher Vorstufenpulver N2 - The main focus of this work was to get a deeper understanding of the relationship between the structure of sol-gel films, their densification and their macroscopic cracking. First of all titania was chosen as model system. Therefore a synthesis route starting from the preparation of long-term stable amorphous redissoluble precursor powders based on acetylacetone as chelate ligand was utilized. The solubility and stability of the powders in various solvents can be determined by chemical synthesis and technological parameters. When dissolved in a solvent mixture of ethanol and 1,5-pentanediol, thin films can be easily prepared by dip-coating technique. Thereby the quality of the titania films enormously depends on the calcinations temperature and the solvent mixture is used. In order to investigate the influence of different solvents and solvent mixtures on the microstructure and densification of the precursors, the coating solutions were stripped off (sol powder) and analyzed as function of annealing temperature. It was pointed out that a high densification rate caused by the addition of 1,5-pentanediol, results in dense microstructure with trapped residual carbon. These impurities can retard the phase transformation of anatase to rutile. The analysis of so-called “film powders” scraped off multiple dip-coated substrates provides valuable information on the effect of air moisture and unidirectional densification during drying and aging on the structure of thin films. The high surface-to-volume ratio and access to air moisture determine the chemical composition of the as-prepared film, which controls shrinkage, crystallization and defect structure of the coatings. Further it was shown, that drying as a thin film results in the formation of closed pores and much denser microstructure than the respective sol powder. Without the addition of 1,5-pentanediol all –OEt moieties undergo hydrolysis reactions, which causes the formation of a rigid network. The presence of 1,5-pentanediol retards this hydrolysis reactions and provides some network plasticity. Generally the microstructure of thin films is comparatively close to the microstructure of the film powders. The addition of 1,5-pentandiol prevents hydrolysis and condensation reactions as like in the film powders. However even at 700 °C, thin films never transform to rutile, which was attributed to the tensile stresses in thin films. In thin films and in film powders as well a comparable amount of closed pores are formed during annealing. Further it was shown that most of the thin sol-gel films investigated form a dense crust on their tops during annealing. This explains why crack free films exhibit only closed pores. However, when cracks appear during thin film shrinkage in the coating, this crust is burst, which generates open porosity. The defect density in the coatings was determined by an automated analysis of surface images. The crack formation and quantity can be directly referred to tensile stresses in the coatings, which arise from hydrolysis and condensation during thin film drying and aging. Therefore when 1,5-pentanediol is added to the sol, thin film cracking was avoided, because hydrolysis and condensation reactions are retarded, which preserves a higher network flexibility. Furthermore the crack formation was significantly influenced by the atmospheric humidity that was used during the coating process, which was explained by different drying and condensation rates. Under certain chemical starting conditions water soluble precursor powders can be also obtained. In general the observations made with the water based coating solutions are mostly in agreement with the former results based on ethanol based coating solutions. For example the high surface-to-volume ratio of film powders compared to sol powders also significantly enhances film drying and densification. The addition of 1,5-pentanediol also clearly contributes to their densification behavior and phase evolution. As seen before in the case of ethanol based coatings, 1,5-pentanediol enhances the stability towards hydrolysis and condensation reactions and preserves some network plasticity. Therefore coatings prepared without the addition of 1,5-pentanediol already form cracks during film drying and aging because of tensile stresses. Thus, the addition of 1,5-pentanediol results in a reduction/prevention of crack formation. Nevertheless some differences were observed, i.e. the critical single coating film thickness of ethanol based coatings is nearly twice that of water based coatings. This was explained by the different surface tensions of the basis solvents, which during thin film drying causes significantly higher capillary forces and tensile stresses in water based coatings. When acetylacetone is replaced by triethanolamine as chelating ligand for titanium also re-dissolvable precursor powders can be synthesized. The film powders combine a high hydrolytic stability of the precursor with sufficient intermediate network flexibility. The different type of organics changes the drying and densification behavior: i.e. in contrast to film powders obtained from acetylacetone based precursor powders the structure of triethanolamine based film powders is unaffected by the thin film drying process. This high hydrolytic stability and plasticity of this precursor allows the preparation of defect free coatings up to single film thickness of 300 nm. However triethanolamine based thin films present at intermediary annealing temperatures a distinctively different microstructure compared to acetylacetone based films. The general validity of the conclusions was proved on the basis of zirconia coatings that were also prepared by the use of re-dissolvable precursor powders. In principle all conclusions concerning the interconnection of precursor chemistry, film formation, densification and structure were transferable to the respective zirconia coatings. Differences mainly arise only from differential material properties i.e. bulk density. Finally, it has been pointed out that the findings obtained on the densification behavior of thinsol-gel films are also a valuable tool for improved explanations of other important scientific questions concerning sol-gel films, i.e. scratch resistance of sol-gel coatings, fiber -bridging and – degradation of sol-gel coated fibers. N2 - Grundsätzlich war es Ziel der vorliegenden Arbeit, die Zusammenhänge zwischen Struktur von Sol-Gel Schichten, ihrer Verdichtung und der Entstehung von makroskopischen Rissen besser verstehen zu können. Als Modelsystem wurde hierfür Titanoxid ausgewählt. Hierzu wurde von einer Syntheseroute basierend auf der Verwendung von langzeitstabilen amorphenre-dispergierbaren Vorstufenpulvern mit Acetylaceton als Chelatligand ausgegangen. Die Löslichkeit und Stabilität der Pulver in verschiedenen Lösungsmitteln lässt sich über die chemische Synthese bzw. technologischen Parameter einstellen. Wenn die Pulver in einem Lösungsmittelgemisch aus Ethanol und 1,5-Pentandiol gelöst werden, lassen sich mittels Tauchbeschichtungsverfahren einfach dünne Schichten herstellen. Die Qualität der Titanoxidschichten hängt dabei entscheidend von der verwendeten Pyrolysetemperatur und der Menge an verwendetem 1,5- Pentandiol ab. Um den Einfluss von verschiedenen Lösungsmitteln und Lösungsmittelgemischen auf die Mikrostruktur und Verdichtung der Vorstufen zu untersuchen, wurden die Sole am Rotationsverdampfer eingeengt (Sol-Pulver) und in Abhängigkeit von der Behandlungstemperatur analysiert. Dabei stellte sich heraus, dass eine hohe Verdichtungsrate verursacht durch den Zusatz von 1,5-Pentandiol, in einer dichten Mikrostruktur mit eingeschlossenem Rest-Kohlenstoff resultiert. Diese Kohlenstoff-Rückstände können die Phasenumwandlung von Anatas zu Rutil hemmen. Die Analyse der so genannten „Film-Pulver“, welche von mehrfach tauchbeschichteten Substraten abgekratzt worden sind, ermöglicht den Zugang zu entscheidenden Informationen über den Einfluss der Luftfeuchtigkeit und der unidirektionalen Verdichtung, während der Film-Trocknung und –Alterung, auf die Struktur der dünnen Schichten. Es zeigte sich, dass das große Oberfläche zu Volumen Verhältnis und der Kontakt mit Luftfeuchtigkeit die chemische Zusammensetzung der frisch hergestellten Schichten bestimmen. Diese wiederum steuert die Schichtschrumpfung, Kristallisation und Defektstruktur der Schichten. Ferner konnte dargestellt werden, dass die Trocknung als dünner Film zu der Entstehung von geschlossenen Poren und zu einer deutlich dichteren Mikrostruktur als die der entsprechenden Sol-Pulver führt. Ohne den Zusatz an 1,5-Pentandiol kommt es zur Hydrolyse der –OEt Gruppen, was die Bildung eines rigiden Netzwerks bewirkt. 1,5-Pentandiol als Zusatz hemmt diese Hydrolysereaktionen und bedingt damit eine gewisse Plastizität des Netzwerkes. Im Großen und Ganzen ist die Mikrostruktur der dünnen Schichten mit der Struktur der Film-Pulver gut vergleichbar. Durch den Zusatz an 1,5-Pentandiol werden in den Schichten die Hydrolyse und Kondensationsreaktionen ebenso gehemmt wie in den entsprechenden Film-Pulvern. Allerdings bei den dünnen Schichten ist auch bei 700 °C keine Phasenumwandlung zu beobachten, was auf Zugspannung in den dünnen Filmen zurückzuführen ist. Während der Calcinierung kommt es sowohl in dünne Schichten wie als auch in den Film-Pulvern zur Ausbildung von geschlossenen Poren. Ferner wurde gezeigt, dass die meisten untersuchten dünnen Schichten während der Pyrolyse auf ihrer Oberfläche eine dichte Kruste ausbilden. Dies erklärt warum rissfreie Schichten nur geschlossene Poren aufweisen. Allerdings wenn Risse während der Schichtschrumpfung in der Schicht auftreten, wird diese Kruste durchbrochen, was zur Bildung von offener Porosität führt. Die Defektdichte in den Schichten wurde mittels einer automatisierten Bildanalyse der Oberfläche bestimmt. Die Riss-Bildung und Riss-Häufigkeit kann dabei direkt mit der Entstehung von Zugspannung, durch Hydrolyse und Kondensation während der Schicht-Trocknung und –Alterung, in Zusammenhang gebracht werden. Durch die Zugabe von 1,5-Pentandiol konnte die Rissentstehung verhindert werden, da Hydrolyse und Kondensations-Reaktionen gehemmt werden, was eine höhere Flexibilität des Netzwerkes erhält. Weiterhin wurde die Rissentstehung signifikant durch die herrschende Luftfeuchtigkeit während es Beschichtungsprozesses beeinflusst, was mit unterschiedlichen Hydrolyse- und Kondensations-Raten zu erklären ist. Unter Verwendung bestimmter chemische Syntheseparameter, können ebenso wasserlösliche Vorstufenpulver erhalten werden. Grundsätzlich sind die Untersuchungen an den hieraus resultierenden wässrigen Solen und Schichten in guter Übereinstimmung mit den vorherigen Untersuchungen an ethanolischen Beschichtungssystemen. So zum Beispiel, beschleunigt ebenso das große Oberfläche zu Volumen Verhältnis der Film-Pulver deutlich die Film-Trocknung und –Verdichtung, im Vergleich zu den Sol-Pulvern. Auch beeinflusst ein Zusatz an 1,5-Pentandiol eindeutig das Verdichtungsverhalten und die Phasenentwicklung. Wie schon bereits im Fall der Ethanol basierenden Beschichtungen festgestellt worden ist, erhöht 1,5-Pentandiol die Beständigkeit hinsichtlich Hydrolyse und Kondensationsreaktionen und erhält hiermit eine gewisse Netzwerkplastizität. Deshalb bilden Filme die ohne einen Zusatz an 1,5-Pentandiol hergestellt worden sind, aufgrund von Zugspannung, schon während der Film-Trocknung und -Alterung Risse aus. Durch einen Zusatz von 1,5-Pentandiol kann dagegen die Entstehung von Rissen vermindert bzw. vermieden werden. Allerdings zeigten sich auch einige Unterschiede: So ist zum Beispiel die erreichbare Einzelschichtdicke der ethanolischen Beschichtungssystemen nahezu doppelt so groß wie die der wässrigen Beschichtungssysteme. Dies wurde mit der unterschiedlichen Oberflächenspannung des Basislösungsmittels erklärt, welche während der Schichttrocknung deutlich höhere Kapillarkräfte und Zugspannung in wässrigen Filmen erzeugt. Wird Acetylaceton gegen Triethanolamin als Chelatligand für Titan ausgetauscht, so können ebenso re-dispergierbare Vorstufenpulver hergestellt werden. Die Film-Pulver kombinieren hohe hydrolytische Stabilität der Vorstufe mit einer ausreichenden intermediären Netzwerkflexibilität. Der andere Komplexbildner verändert entscheidend das Trocknungs- und Verdichtungs-Verhalten: so z.B. wird die die Struktur von Film-Pulvern basierend auf Triethanolamin nicht entscheidend durch die Trocknung als dünne Schicht beeinflusst, im Gegensatz zu Film-Pulvern hergestellt von Vorstufenpulvern mit Acetylacetone als Chelatligand. Diese hohe hydrolytische Stabilität und Plastizität der Vorstufe ermöglicht die Herstellung von defektfreien Beschichtungen bis hin zu einer Einzelschichtdicke von 300 nm. Dennoch unterscheidet sich bei intermediären Pyrolysetemperaturen die Mikrostruktur der Triethanolamin basierenden Schichten deutlich von der auf Acetylaceton basierenden Schichtsystemen. Die Allgemeingültigkeit der Schlussfolgerungen wurde anhand Zirkonoxidbeschichtungen, welche ebenfalls unter Verwendung von löslichen Vorstufenpulvern hergestellt worden sind, überprüft. Grundsätzlich zeigte sich hierbei, dass alle Schlüsse hinsichtlich der Zusammenhänge der Vorstufenchemie, Film-Bildung, -Verdichtung und –Struktur auf die entsprechenden Zirkonoxidbeschichtungen übertragbar sind. Unterschiede ergeben sich nur aus unterschiedlichen Materialeigenschaften wie z.B. der makroskopischen Dichte. Letztlich wurde dargestellt, dass die Erkenntnisse hinsichtlich des Verdichtungsverhalten der Sol-Gel Schichten die Grundlage für die Aufklärung vieler anderer wichtiger wissenschaftlich Fragestellungen hinsichtlich Sol-Gel Beschichtungen bilden, wie z.B. der Kratzfestigkeit von Sol-Gel Schichten, Faser-Verbrückung und -Schädigung von Sol-Gel beschichten Fasern. KW - Sol-Gel-Verfahren KW - Dünne Schicht KW - Titan KW - Titandioxid KW - Dünnfilm KW - thin film KW - sol-gel KW - titania Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-24577 ER - TY - THES A1 - Delporte, Marc T1 - A phenomenological approach to the prediction of material behaviours during co-sintering N2 - This work deals with the sintering of multi-material composites. It aims at the establishment of an alternative to the existing complex models for sintering. The development of the associated experimental procedure is also included in this work. The developed material model must be able to predict (i) the sintering kinetics and (ii) the viscous moduli of a material. An experimental approach with free sintering and hot-forging measurements is favoured in this work. The prediction of the sintering kinetics is addressed with the construction of a map of sintering kinetics data: the Master Sintering Diagram (MSD). The MSD is based on a generalized equation for solid-state diffusion, thus is suitable for any thermal activated diffusion. The MSD allows the prediction of sintering kinetics for a large range of temperatures and external loads. A novel approach to the determination of the viscous moduli is developed in this work: the cyclic unloading method. It is a hot-forging measurement (sintering under uniaxial compression) where the applied load is released for short periods. The measurements are carried out with continuous heating, so that the viscous moduli are determined over large ranges of temperatures and densities. The advantage of this method is the measurement of the viscous moduli in anisotropic microstructures. The material model is validated in two steps. Firstly, the predictions of sintering kinetics with the MSD are compared with experimental results: changes of thermal profile and changes of load are predicted with a maximum deviation of 10%. Secondly, the experimentally determined viscous moduli are used for the prediction of a bi-layer curvature using models for warpage from literature. The prediction is qualitatively good for a maximum deviation of 27%. The study of a sintering glass-ceramic tape on a rigid substrate is presented. It shows that this co-sintering problem can be qualitatively investigated with requirement of the material model. The formation of anisotropy intrinsic to the hot-forging experiments is also reported in this work. It appears to be a important point to address in the future for a better understanding of the cosintering. N2 - Die vorliegende Arbeit behandelt das Thema Kosintern. Ziel ist, die bisher verwendeten komplexen Sintermodelle durch ein einfacheres Verfahren zu ersetzen. Zusätzlich wird ein Messverfahren entwickelt, um die zur Beschreibung des Kosinterns erforderlichen Messdaten zu erhalten. Der experimentelle Ansatz beinhaltet Sinterungen ohne Last sowie mit einachsiger Belastung. Das Verfahren ermöglicht die Vorhersage (i) der Sinterkinetik und (ii) der viskosen Moduli. Um den Sinterpfad von Grünkörpern vorhersagen zu können, wird ein Kennfeld verwendet: das Master Sintering Diagram (MSD). Das MSD wird durch eine allgemeine Gleichung für das Festphasensintern definiert und lässt sich damit für alle thermisch aktivierten Diffusionsmechanismen anwenden. Die Vorhersage gilt für breite Bereiche von Temperaturen und äußeren Lasten. Eine neuartige Messmethode für die Erfassung der viskosen Moduli wird in der Arbeit entwickelt: das cyclic unloading dilatometry. Sie besteht in Hot-forging Versuchen mit konstanter Last, bei denen die sinterenden Proben regelmäßig für kurz Zeit entlastet werden. Die Versuche werden mit konstanter Aufheizrampe durchgeführt, so dass die viskose Moduli für breite Bereiche von Temperaturen und Dichten erfasst werden. Ein Vorteil dieser Messmethode ist es, die viskosen Eigenschaften von anisotropen Materialien messen zu können. Das Vorhersageverfahren wird in zwei Schritten geprüft. Erstens werden Vorhersagen vom MSD mit experimentellen Daten verglichen: die maximale Abweichung bei Änderung der Temperaturrampe und der ¨außeren Last liegt bei 10%. Zweitens werden die viskose Moduli aus dem MSD zur Vorhersage der Krümmung eines Zweischicht-Systems verwendet. Dazu wird ein in der Literatur beschriebenes Modell verwendet. Die qualitative Vorhersage ist gut: die maximale Abweichung zur experimentellen Krümmung liegt bei 27%. Zusätzlich wird eine Studie über ein Zweischicht-System aus Glas und Keramik vorgestellt, bei dem die Keramik nicht sintert. Es wird gezeigt, dass dieser Fall ohne Hilfe des Sintermodells qualitativ verstanden werden kann. Die Entwicklung der Anisotropie in der Mikrostruktur der keramischen Grünkörper durch die anisotrope Last beim Sintern wird diskutiert. Das volle Verständnis der anisotropen Mikrostrukturentwicklung beim Sintern unter anisotropen Randbedingungen erfordert weitere Arbeiten. KW - Sintern KW - sintering KW - modelling KW - composites Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-44235 ER - TY - THES A1 - Declerck, Pélagie T1 - Synthesis and technological processing of hybrid organic-inorganic materials for photonic applications T1 - Synthese und technische Prozesse von organisch-anorganischen Hybridmaterialien für photonische Anwendungen N2 - Im Rahmen dieser Doktorarbeit wurden neue UV-strukturierbare organisch-anorganische hybride Polymere für photonische Anwendungen mit einem hohem Brechungsindex und der Möglichkeit, sie durch Ein- bzw. Zwei-Photonen-Polymerisation zu strukturieren, entwickelt. Die Materialien wurden in Bezug auf ihre chemische Struktur, ihre optischen Eigenschaften, und ihrer Fähigkeit, durch 1PP und 2PP strukturierbar zu sein, untersucht. Besonders mit 2PP konnte man mit diesen neuartigen hybriden Materialien 3D-Strukturen erzeugen. ie Hydrolyse und Polykondensationsreaktionen wurden mit · Organo-Alkoxysilanen und Titanalkoxiden, modifiziert mit und ohne komplexierende Liganden und · Organo-Alkoxysilanen, Titanalkoxiden und Organophosphorsäure als Precrusoren durchgeführt. Primäres Ziel dieser Arbeit war es, den Brechungsindex von ORMOCER®en, die auf der Basis von Organo-Alkoxysilan-Precursoren ohne Heteroelemente synthetisiert werden, zu vergrößern. Die chemische Struktur der synthetisierten Materialien und somit mit ihr die Parameter, die den Brechungsindex beeinflussen, wurden eingehend untersucht. Insbesondere die Synthese-Parameter, wie das Einsetzen der Titanalkoxide und ihrer Konzentration, der Organo-Alkoxysilane, die Katalysator-Konzentration, die verwendeten Lösungsmittel und auch die Verfahrensparameter für eine spätere Strukturierung durch lithographische Verfahren, wie die UV-Bestrahlungsdosis, die Initiator-Konzentration und der Entwickler, wurden untersucht. N2 - In the framework of this thesis, new UV-patternable organic-inorganic hybrid polymers with higher refractive indices than reported in the literature for photonic applications were developed and studied with respect to their chemical structure, their optical properties, and their ability of being patterned by 1PP and 2PP. Particularly with 2PP, one could create 3D structures using the novel hybrid materials. The materials were prepared from hydrolysis and polycondensation reactions of · organo-alkoxysilanes and titanium alkoxide precursors, modified with and without CL and organo-alkoxysilanes precursors, and · organo-alkoxysilanes, titanium alkoxide and organophosphorus precursors. The major scope of this work was to increase the refractive index of ORMCER® materials based on only organo-alkoxysilanes. Thus, the parameters which influence the refractive index were investigated thoroughly. In particular, the synthesis parameters such as the introduction of titanium alkoxide and its concentration, the organo-alkoxysilanes, the catalyst concentration, the solvent used, but, also the processing parameters such as, the UV exposure dose, initiator concentration, and developer were investigated. KW - Brechzahl KW - Ormocer KW - Photonischer Kristall KW - Sol-Gel-Verfahren KW - Photolithographie KW - Titan KW - refractive index KW - Ormocer KW - sol-gel KW - photonic crystal Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-56053 ER - TY - THES A1 - Götzendörfer, Stefan T1 - Synthesis of Copper-Based Transparent Conductive Oxides with Delafossite Structure via Sol-Gel Processing T1 - Synthese von Kupfer-basierten transparenten leitfähigen Oxiden mit Delafossit-Struktur über das Sol-Gel-Verfahren N2 - Starting off with solubility experiments of possible precursors, the present study reveals the whole development of a sol gel processing route for transparent p type semiconductive thin films with delafossite structure right to the fabrication of functional p-n junctions. The versatile sol formulation could successfully be modified for several oxide compositions, enabling the synthesis of CuAlO2, CuCrO2, CuMnO2, CuFeO2 and more. Although several differences in the sintering behaviour of powders and thin films could be observed, the powder experiments significantly contributed to the clearification of the intricate phase development during thermal annealing and also to optimization of the annealing sequence for thin film processing. Two different ternary systems turned out to be the most promising candidates for p-TCO application: Copper aluminum oxide for its high optical transmittance and copper chromium oxide for its low synthesis temperature, which allowed thin film deposition on low-cost borosilicate substrates. In order to combine the advantages of these two systems, the quaternary oxide composition CuAl1-xCrxO2 was investigated. With a higher optical transmittance than CuCrO2, a lower synthesis temperature than CuAlO2 and a lower resistivity than both parent systems, the optimum composition of the quaternary oxide is reached for x = 0.50. Compared to physical vapour deposition techniques, the undoped thin films presented here still need to make up some deficites in their optoelectronic performance. Although the best sol-gel samples are able to compete with RF sputtered samples or sampes deposited by PLD in transmittance, their resistivity is almost two orders of magnitude higher. The most probable reasons for this are the characteristic imperfections of sol-gel thin films like porosity and small crystallite size, which create barriers like grain boundaries and bottlenecks like barely connected particles. By additional effort such shortcomings can be repelled to a certain extend, but nevertheless the density of undoped sol-gel material always stays behind its pendants processed by physical vapour deposition.[246] Furthermore, such additional endeavour is likely to annihilate the advantage of sol-gel technique in processing costs. Extrinsic doping is a common method to decrease the resistivity of delafossite materials. Partially replacing the trivalent cations by divalent ones creates additional holes and thus generates additional charge carriers for p-type semiconductivity. This can improve the conductivity of delafossites by up to three orders of magnitude. Due to the compositorial flexibility of sol-gel processing, dopants could be introduced easily in this study by soluble precursors. However, improving the conductivity of CuAlO2 and CuAl0.5Cr0.5O2 via this method failed. Actually, this seems to be due to the fact that instead of being incorporated into the delafossite phase the dopant ions form intransparent phase impurities like spinels, which interfere with optical transmittance of the thin films. On the contrary, doping had a positive effect on the conductivity and the optical transmittance of copper chromium oxide, with magnesium being the most effective dopant. The resistivity could be decreased by more than three orders of magnitude, but in order to achieve this, much higher Mg concentrations than by other thin film deposition methods were necessary. This indicates a low doping efficiency in sol gel processed thin films, but also the ability of sol gel processing to incorporate more magnesium into the oxide than any other processing method. The extensive substitution of the chromium ions also increases the optical transmittance and allows sol gel processed thin films to draw level with thin films deposited by sputtering methods or PLD. Finally, the applicability of the delafossite thin films was proven by the asymmetric current voltage characteristics of heterojunctions between ITO and the delafossites. Shunting problems of the metallic contacts, on the other hand, reveal structural deficites of the delafossites, which should be the subject of further investigations. N2 - Ausgehend von Versuchen zur Löslichkeit möglicher Ausgangsstoffe zeigt die vorliegende Studie die komplette Entwicklung einer Sol-Gel-Route für die Synthese transparenter p-halbleitfähiger Dünnschichten mit Delafossitstruktur bis hin zur Herstellung funktionstüchtiger p-n-Übergänge. Die vielseitige Solrezeptur konnte erfolgreich für mehrere Oxidzusammensetzungen abgewandelt werden, was die Synthese von CuAlO2, CuCrO2, CuMnO2, CuFeO2 und weiteren Mischoxiden ermöglichte. Obwohl einige Unterschiede im Sinterverhalten von Pulvern und Dünnschichten beobachtet werden konnten, trugen die Pulverversuche erheblich zur Aufklärung der komplizierten Phasenentwicklung während der thermischen Behandlung und auch zur Optimierung der Kalzinierungsschritte bei der Dünnschichtherstellung bei. Zwei der ternären Oxide erwiesen sich als die vielversprechendsten Kandidaten für die Anwendung als p-halbleitfähiges transparentes Oxid: Kupfer-Aluminium-Oxid aufgrund seiner hohen optischen Transparenz und Kupfer-Chrom-Oxid aufgrund seiner niedrigen Synthesetemperatur, die die Abscheidung von Dünnschichten auf kostengünstigen Borosilicatglas-Substraten ermöglicht. Um die Vorteile dieser beiden Systeme zu vereinen, wurde die quaternäre Oxidzusammensetzung CuAl1-xCrxO2 untersucht. Mit einer höheren optischen Transmission als CuCrO2, einer niedrigeren Synthesetemperatur als CuAlO2 und einem geringeren spezifischen Widerstand als die beiden Muttersysteme wird die optimale Zusammensetzung dieses quaternären Oxids bei x = 0,50 erreicht. Im Vergleich zu Methoden der physikalischen Gasphasenabscheidung müssen die hier vorgestellten undotierten Dünnschichten noch einige Defizite bei ihren optoelektronischen Eigenschaften aufholen. Obschon die besten Sol-Gel-Proben in puncto Transparenz mit Proben, die über Radiofrequenz-Kathodenzerstäubung oder Laserstrahlverdampfen hergestellt wurden, mithalten können, liegt ihr spezifischer Widerstand um zwei Größenordnungen höher. Die wahrscheinlichste Ursache hierfür sind die charakteristischen Unvollkommenheiten von Sol-Gel-Dünnschichten wie Porosität und geringe Kristallitgröße, die den Stromfluss durch Hindernisse wie Korngrenzen und Engpässe wie schlecht verknüpfte Partikel behindern. Durch zusätzlichen Aufwand können derartige Unzulänglichkeiten in gewissem Maße zurückgedrängt werden, doch nichtsdestotrotz liegt die Dichte von undotiertem Sol-Gel-Material immer unter der von vergleichbaren Proben, die über physikalische Gasphasenabscheidung hergestellt wurden.[246] Zudem ist es wahrscheinlich, dass solche zusätzlichen Anstrengungen die Vorteile des Sol-Gel-Verfahrens bei den Herstellungskosten zunichte machen. Extrinsische Dotierung ist ein gängiger Weg, um den spezifischen Widerstand von Delafossit-Materialien abzusenken. Teilweiser Austausch der dreiwertigen Kationen durch zweiwertige erzeugt zusätzliche Löcher und stellt so zusätzliche Ladungsträger für die p-Halbleitung bereit. Dies kann die Leitfähigkeit von Delafossiten um bis zu drei Größenordnungen erhöhen. Dank der stofflichen Flexibilität des Sol-Gel-Verfahrens konnten in dieser Studie Dotanden sehr leicht in Form von löslichen Vorstufen eingebracht werden. Jedoch scheiterten die Versuche, die Leitfähigkeit von CuAlO2 und CuAl0,5Cr0,5O2 auf diesem Wege zu verbessern. Dies scheint darauf zurückzuführen zu sein, dass die Dotanden nicht in die Delafossitphase eingebaut werden, sondern intransparente Fremdphasen wie Spinelle bilden, die die optische Transmission der Dünnschichten beeinträchtigen. Im Gegensatz dazu wirkte sich die Dotierung positiv auf die Leitfähigkeit und die optische Transmission von Kupfer-Chrom-Oxid aus, wobei Magnesium als Dotant die besten Resultate lieferte. Der spezifische Widerstand konnte so um mehr als drei Größenordnungen verringert werden, doch wurden hierfür deutlich höhere Magnesiumkonzentrationen benötigt als bei anderen Beschichtungsverfahren. Einerseits weist dies auf eine geringe Dotiereffizienz in den über das Sol-Gel-Verfahren hergestellten Proben hin, andererseits zeigt dies aber auch, dass über das Sol-Gel-Verfahren wesentlich mehr Magnesium in die Oxidschichten eingebracht werden kann als über jedes andere Verfahren. Der beträchtliche Ersatz der Chromionen erhöht auch die optische Transmission und ermöglicht es den Sol-Gel-Proben, zu den Dünnschichten aufzuschließen, die durch Kathodenzerstäuben oder Laserstrahlverdampfen hergestellt wurden. Schließlich wurde das Anwendungspotential der Delafossit-Dünnschichten durch die asymmetrischen Strom-Spannungs-Kennlinien von p-n-Übergängen zwischen Delafossit und Indium-Zinn-Oxid belegt. Andererseits machen die Kurzschlussprobleme bei der metallischen Kontaktierung die strukturellen Defizite der Delafossite deutlich. Dies sollte zum Gegenstand weiterführender Untersuchungen werden. KW - Transparent-leitendes Oxid KW - p-Halbleiter KW - Sol-Gel-Verfahren KW - Beschichtung KW - pn-Übergang KW - Delafossit KW - Kupfer-Chrom-Oxid KW - Kupfer-Aluminium-Oxid KW - Delafossite KW - Copper-Chromium-Oxide KW - Copper-Aluminum-Oxide Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-51601 ER - TY - THES A1 - Pietschmann, Bernd T1 - Elektrorheologische Flüssigkeiten auf Basis von mit ionischen Flüssigkeiten modifizierten Silica-Materialien T1 - Electrorheological fluids consisting of ionic liquid modified silica particles N2 - Die vorliegende Arbeit befasst sich mit der Synthese und Charakterisierung von elektrorheologischen Flüssigkeiten (ERF), deren Aktivität durch den Einsatz von imidazoliumhaltigen ionischen Flüssigkeiten (IL) hervorgerufen wird. Diese sind in eine Matrix aus selbst hergestellten, geordneten mesoporösen Silica-Partikeln (SBA-15) eingebettet. Die IL wird während der Modifizierungsreaktion in die Poren des SBA-15 über intermolekulare Wechselwirkungen eingelagert, wobei die Porosität des Systems erhalten bleibt. Durch Optimieren der Reaktionsparameter kann der Prozess hinsichtlich seiner ökonomischen und ökologischen Effizienz gesteigert werden. Der Anteil an ionischer Flüssigkeit im System kann hierbei gezielt eingestellt werden. Als Dispergiermedium der ERF wird Siliconöl eingesetzt, wobei die rheologischen Eigenschaften der erhaltenen Suspensionen je nach Feststoffgehalt und Konzentration an ionischer Flüssigkeit variieren. Im elektrischen Feld zeigen die Suspensionen eine deutliche elektrorheologische (ER-)Aktivität, während IL-freie SBA-15 Dispersionen in Siliconöl nicht ER-aktiv sind. Die Ursache des ER-Effekts sind Polarisationsprozesse, die in den modifizierten SBA-15 Partikeln durch Verschieben von Ionen hervorgerufen werden und mit Hilfe der Impedanzspektroskopie nachgewiesen werden konnten. Die Größe des ER-Effekts ist von einer Vielzahl an Parametern abhängig, vor allem vom Feststoffgehalt der Suspension, von der Art und der Konzentration der im Feststoff eingelagerten ionischen Flüssigkeit, der Temperatur und der elektrischen Feldstärke. Unter optimalen Umständen konnten mit den ERF bei Messung in Rotation (Scherrate 1000 s−1) Schubspannungen über 3000 Pa erreicht werden. Diese Werte wurden von bisher veröffentlichten Silica-haltigen elektrorheologischen Flüssigkeiten nicht erzielt. Aufgrund der gezeigten Effekte sind die in dieser Arbeit beschriebenen Dispersionen in die Gruppe der klassischen dielektrischen ERF einzuordnen. Der Vorteil liegt in der porösen Struktur der Feststoffpartikel, in die das elektrorheologisch aktive Additiv eingebracht werden kann, um dort im elektrischen Feld eine maximale Polarisation der Feststoffpartikel zu bewirken. Grundsätzlich eignen sich die im Rahmen dieser Arbeit hergestellten Dispersionen als ERF, besitzen jedoch noch Optimierungsbedarf. N2 - In this work the synthesis and characterization of a new kind of electrorheological fluids (ERF) is described whose ER activity is caused by imidazolium-containing ionic liquids (IL). They are embedded in a host matrix of self synthesized ordered mesoporous silica particles (SBA-15). The ionic liquid is immobilized within the pores by inter-molecular interactions whereas the porosity of the system is remained. The amount of embedded IL within SBA-15 can be exactly controlled and the economical and ecological efficiency of the process are improved by optimizing the reaction conditions. Silicone oil is used as the dispersing agent of the ERF and the rheological properties of the obtained suspensions vary as a function of the solid content and the concentration of embedded IL. If an electric field is applied the suspensions show considerable ER activity whereas dispersions of pure SBA-15 particles within silicone oil reveal no electrorheological activity. The ER effect is caused by polarization processes which originate within the modified SBA-15 particles by movement of ions which was proved by impedance spectroscopy. The magnitude of the ER effect depends on various parameters especially the solid content of the suspension, the kind and the concentration of IL embedded within the solid particles, the temperature and the applied electric field strength. Under optimum circumstances a shear stress higher than 3000 Pa was achieved in a rotating system at a shear rate of 1000 s−1. This value has not been reached yet by ERF which contain porous silica particles. Because of the shown effects the suspensions which are described in this work can be classified as classical dielectric ER fluids. The advantage is the porous structure of the solid particles in which the electrorheological active additive can be immobilized, in order to cause a maximum polarization of the solid particles. Basically the here reported synthesized dispersions are suitable to be used as electrorheological fluids but there is still need for improvement. KW - Elektrorheologie KW - Siliciumdioxid KW - Fluid-Feststoff-System KW - Ionische Flüssigkeit KW - adaptive Materialien KW - elektrorheologische Flüssigkeit KW - mesoporöse Silica KW - electrorheological fluid KW - ionic liquid KW - smart material KW - mesoporous silica Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-77468 ER - TY - THES A1 - Platte, Daniela T1 - Grenzflächenselektive Verkapselung von anorganischen Latentwärmespeichermaterialien mit Hybridpolymeren T1 - Interface-selective encapsulation of inorganic phase change materials with hybrid polymers N2 - Im Rahmen dieser Arbeit wurde ein prinzipieller Zugang zur Mikroverkapselung anorganischer Latentwärmespeichermaterialien (LWS) erarbeitet. Dazu wurden zwei basische, kristallwasserreiche Salzhydrate mit Schmelztemperaturen im Umgebungstemperaturbereich als Kernmaterialien und anorganisch-organische Hybridpolymere mit kovalent verbundenen anorganischen und organischen Struktureinheiten (ORMOCER®e) als Verkapselungsmaterial verwendet. Der Prozess verläuft grenzflächenselektiv in der flüssigen Phase, initiiert durch die basischen LWS, in Form einer auch bei milden Temperaturen ablaufenden Michael-Typ-Addition zwischen Acrylat- (Acr) und Thiolmonomeren (SH). Optimierte Verkapselungsergebnisse wurden mit Hybridmonomeren erreicht, deren funktionelle Gruppen in einem unstöchiometrischen Verhältnis von Acr:SH ≈ 5:1 vorlagen und über das anorganische Rückgrat vorverknüpft waren. Bei Verwendung eines Mikrodosiersystems wurden gleichmäßige, geschlossene Mikrokapseln mit Durchmessern von etwa 40–50 µm bei Schichtdicken von < 5 µm erhalten. Aufgrund einer zu geringen inhärenten Barrierewirkung der verwendeten Hybridpolymere gegenüber Wasserdampf konnten jedoch erhebliche Kristallwasserverluste nicht verhindert werden, sodass die erhaltenen Mikrokapseln noch nicht zur Anwendung als LWS geeignet sind. Da die beobachtete Tolerierung und sogar Bevorzugung für das deutliche Missverhältnis zwischen den polymerisierenden Gruppen für eine Stufenpolymerisation sehr ungewöhnlich ist, wurden an Modellsystemen Untersuchungen zur Aufklärung des Reaktionsmechanismus vorgenommen. Dazu wurde zunächst ein Mercaptosiloxan (MS) hergestellt, dessen Ringgrößen- bzw. Funktionalitätsverteilung mittels 29Si-NMR- und GPC-Messungen sehr gut aufgeklärt werden konnte. Dieses wurde für Verkapselungsversuche mit Trimethylolpropantriacrylat (TMPTA) kombiniert und das Verhältnis funktioneller Gruppen Acr:SH systematisch variiert. An den erhaltenen Proben konnte via µ-Raman-Tiefenscan-Untersuchungen der Einfluss der Harzzusammensetzung auf die Kapselschichten aufgeklärt werden. Während bei Acr:SH = 1:1 maximale Schichtdicken erhalten wurden, ergaben sich bei Acrylatüberschuss von 4:1 bis 6:1 optimierte Schichten im Sinne der Vorgaben, die gleichmäßig dünn und vollständig waren. Bei Thiolüberschuss wurden dagegen keine vollständig ausgebildeten Schichten erhalten. Das für die LWS-Verkapselungen verwendete Modellsystem TMPTA/MS wurde zusätzlich in Volumenpolymerisationen in homogener organischer Phase untersucht, die mit der Base Triethylamin initiiert wurden. Dabei wurden die stöchiometriebezogenen Vergelungsgrenzen bestimmt. Die detektierte Grenze bei Acr:SH < 5:1 für Acrylatüberschuss lag signifikant unterhalb von Verhältnissen funktioneller Gruppen, für die in Verkapselungsversuchen noch geschlossene Schichten erhalten wurden. Entlang der flüssig-flüssig-Grenzfläche wird somit der Gelpunkt lokal innerhalb eines breiteren Bereichs des Verhältnisses funktioneller Gruppen in der Harzmischung erreicht, als bei einer Polymerisation im gesamten Volumen. Durch weitergehende Untersuchungen zum Vernetzungsverhalten in Abhängigkeit vom Verhältnis funktioneller Gruppen weiterer Acrylat- und Thiolmonomere mit anderen (durchschnittlichen) Funktionalitäten konnte das grundsätzliche Vorliegen eines Stufenmechanismus untermauert werden. Aus einer Kombination der Flory-Stockmayer-Theorie mit der Carothers’schen Gleichung konnten theoretische Vergelungsgrenzintervalle hergeleitet werden. Die experimentell bestimmten Vergelungsgrenzen standen in vollständiger Übereinstimmung mit den theoretisch errechneten Intervallen. Innerhalb des Modellsystems TMPTA/MS konnten zudem weitere Materialeigenschaften bestimmt und zusätzliche Erkenntnisse zum Vernetzungsverhalten gewonnen werden. Durch In-situ-Messungen mittels µ-Raman-Spektroskopie wurde die Entwicklung der Umsetzungsgrade N(C=C) und N(S–H) von Acrylat und Thiol im Verlauf der Reaktionszeit untersucht. Dabei wurden einige Einschränkungen der verwendeten Messmethode identifiziert und beschrieben. Mittels in-situ-mechanischer Spektroskopie nach Chambon und Winter konnte weiterhin das Vergelungsverhalten des Systems in Abhängigkeit von Monomerzusammensetzung, Initiatorkonzentration und Temperatur und Unterschiede innerhalb der kritischen Gele systematisch charakterisiert werden. Die stabilsten kritischen Gele und kürzesten Gelzeiten wurden für hohe Basenkonzentrationen und bei stöchiometrischem Monomerverhältnis, aber auch für Acrylatüberschuss bis Acr:SH = 3:1, erhalten. Damit konnte auch innerhalb der Volumenpolymerisationen eine Bevorzugung des untersuchten Monomersystems für Acrylatüberschuss nachgewiesen werden. Weiterhin wurde das Geschwindigkeitsgesetz der Reaktion aufgeklärt. Es ergab sich bis zum Gelpunkt, zu je erster Ordnung in den beiden Monomeren und der Initiatorbase. Außerdem wurde die Aktivierungsenthalpie der Polymerisation in homogener Phase mittels einer Arrhenius-Auftragung bestimmt. N2 - In the framework of this thesis, an approach to the microencapsulation of inorganic phase change materials (PCM) was developed. Two alkaline salt hydrate mixtures with high amounts of crystal water and melting ranges at ambient temperature were chosen as core materials. These were encapsulated using hybrid polymers, i.e. materials with covalently connected inorganic and organic moieties (ORMOCER®s). The process developed proceeds as a Michael-type addition polymerization of thiol (SH) to acrylate (Acr) monomers, selectively under mild reaction conditions at the liquid-liquid interface, and it is initiated by the PCM core. Best encapsulation results were obtained using hybrid monomers with organic functional groups, being covalently linked via the inorganic backbone, at a ratio of Acr:SH ≈ 5:1. If a microdispenser was employed to dose the PCM, uniform and enclosed microcapsules of 40–50 µm diameter and < 5 µm coating thickness were produced. The achieved encapsulation performance is a promising improvement towards a hermetic microencapsulation of inorganic PCM. However, due to the inherently too high water vapor permeability of the employed hybrid polymers, the capsules loose water gradually. Therefore, this still inhibits an application as PCM materials for ambient temperatures. Since the preference for off-stoichiometric polymerizing groups which was found is exceptional for a step-growth polymerization, the reaction mechanism was further investigated using a model system. For that purpose, a mercaptosiloxane (MS) was synthesized, whose inorganic condensation was almost exhaustive, and the siloxane ring size and SH functionality distribution, respectively, was well ascertainable through 29Si-NMR and GPC measurements. This material was combined with trimethylolpropane triacrylate (TMPTA) for encapsulation experiments, and the ratio Acr:SH was systematically varied. The influence of the resins’ acrylate to thiol ratio on the encapsulation performance was elucidated by µ-Raman depth scan measurements of the resulting capsules. With a stoichiometric ratio of Acr:SH = 1:1, a maximum coating thickness was obtained, but a significant acrylate excess of about Acr:SH = 4:1 to 6:1 yielded optimized results with respect to the applications requirements: even, thin, and complete coatings. In contrast, no homogeneous coatings were attained with thiol excess in the material. The model system TMPTA/MS was also employed for bulk polymerizations in a homogeneous organic medium, initiated by triethylamine, which allowed the detection of the critical molar ratios (CMR) of TMPTA/MS. The experimental CMR for acrylate excess at Acr:SH < 5:1 was significantly lower than molar ratios that allowed complete PCM capsule coatings. Therefore, the local CMR at the liquid-liquid phase boundary appeared to be considerably enlarged compared to the polymerization in bulk. In the framework of this thesis, an approach to the microencapsulation of inorganic phase change materials (PCM) was developed. Two alkaline salt hydrate mixtures with high amounts of crystal water and melting ranges at ambient temperature were chosen as core materials. These were encapsulated using hybrid polymers, i.e. materials with covalently connected inorganic and organic moieties (ORMOCER®s). The process developed proceeds as a Michael-type addition polymerization of thiol (SH) to acrylate (Acr) monomers, selectively under mild reaction conditions at the liquid-liquid interface, and it is initiated by the PCM core. Best encapsulation results were obtained using hybrid monomers with organic functional groups, being covalently linked via the inorganic backbone, at a ratio of Acr:SH ≈ 5:1. If a microdispenser was employed to dose the PCM, uniform and enclosed microcapsules of 40–50 µm diameter and < 5 µm coating thickness were produced. The achieved encapsulation performance is a promising improvement towards a hermetic microencapsulation of inorganic PCM. However, due to the inherently too high water vapor permeability of the employed hybrid polymers, the capsules loose water gradually. Therefore, this still inhibits an application as PCM materials for ambient temperatures. Since the preference for off-stoichiometric polymerizing groups which was found is exceptional for a step-growth polymerization, the reaction mechanism was further investigated using a model system. For that purpose, a mercaptosiloxane (MS) was synthesized, whose inorganic condensation was almost exhaustive, and the siloxane ring size and SH functionality distribution, respectively, was well ascertainable through 29Si-NMR and GPC measurements. This material was combined with trimethylolpropane triacrylate (TMPTA) for encapsulation experiments, and the ratio Acr:SH was systematically varied. The influence of the resins’ acrylate to thiol ratio on the encapsulation performance was elucidated by µ-Raman depth scan measurements of the resulting capsules. With a stoichiometric ratio of Acr:SH = 1:1, a maximum coating thickness was obtained, but a significant acrylate excess of about Acr:SH = 4:1 to 6:1 yielded optimized results with respect to the applications requirements: even, thin, and complete coatings. In contrast, no homogeneous coatings were attained with thiol excess in the material. The model system TMPTA/MS was also employed for bulk polymerizations in a homogeneous organic medium, initiated by triethylamine, which allowed the detection of the critical molar ratios (CMR) of TMPTA/MS. The experimental CMR for acrylate excess at Acr:SH < 5:1 was significantly lower than molar ratios that allowed complete PCM capsule coatings. Therefore, the local CMR at the liquid-liquid phase boundary appeared to be considerably enlarged compared to the polymerization in bulk. Further analysis of experimental CMR values for other acrylate and thiol monomers with different functionalities confirmed the step-growth behavior of the investigated reaction. By a combination of the theoretical CMRSt after Dušek et al., which is based on the Flory-Stockmayer theory, and the Carothers’ equation, theoretical CMR intervals were derived. The experimentally determined CMRs were all located well within these calculated ranges. For the model system TMPTA/MS, further material properties and additional results on the crosslinking performance were achieved. The conversion progress of acrylate and thiol during polymerization was followed via in situ µ-Raman measurements. This also has revealed some limitations of this spectroscopic method which were specified and considered for data evaluation and interpretation. The gelation characteristics and properties of the critical gels as a function of acrylate to thiol ratio, initiator concentration, and temperature were investigated in situ by means of the mechanical spectroscopy approach after Chambon and Winter. Stiffest critical gels and shortest gelation times were detected at high initiator concentrations and for stoichiometric monomer mixtures as well as for acrylate excess up to Acr:SH = 3:1. Thus, it was possible to prove a preference of this monomer system for an acrylate excess also in bulk polymerizations. Furthermore, the overall rate equation for the polymerization of TMPTA and MS was determined to be third order, and first order in each monomer concentration and in the initiator concentration, respectively, up to the gel point. Finally, the activation enthalpy for the bulk polymerization was found to amount to (18,3 ± 0,7) kJ/mol by means of an Arrhenius plot. KW - Stufenwachstums-Polymerisation KW - Verkapselung KW - Grenzflächenreaktion KW - Raman-Spektroskopie KW - Rheologie KW - Sol-Gel-Verfahren KW - Vernetzung KW - Gelpunkt KW - step-growth polymerization KW - encapsulation KW - gel point KW - Raman spectroscopy KW - mechanical spectroscopy Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-74960 ER - TY - THES A1 - Seyfried, Mona T1 - Neuartige Sulfonsäure-funktionalisierte Polysiloxane für die Anwendung als selbstätzendes Dentaladhäsiv T1 - Novel sulfonic acid functionalized polysiloxanes as self-etching dental adhesives N2 - Der Schwerpunkt dieser Arbeit lag in der Synthese und Charakterisierung von Sulfonsäure bzw. Sulfon - und Carbonsäure - funktionalisierten Polysiloxanen für die Anwendung als selbstätzendes Dentaladhäsiv. Die grundlegende Aufgabe eines Dentaladhäsivs ist es, eine starke und langzeitstabile Verbindung zwischen Zahnhartsubstanz und Kompositmaterial zu gewährleisten. Aktuell auf dem Markt erhältliche selbstätzende Adhäsivmaterialien können jedoch das enorme Anforderungspaket teilweise nur unzureichend erfüllen. Diese enthalten meist Phosphor- bzw. Phosphonsäure - funktionalisierte Monomere, deren Hauptproblem eine ungenügende Ätzwirkung auf Dentin ist. Monomere mit stärkeren Säuregruppen, wie etwa Sulfonsäuregruppen, beschränken sich momentan auf Acrylamidomethyl-propansulfonsäure, welche lediglich in zwei kommerziell erhältlichen Adhäsivsystemen in geringen Mengen zugesetzt wird. Als Folge dieses aktuellen Forschungsbedarfs befasste sich diese Arbeit mit der Synthese und Charakterisierung neuartiger Sulfonsäure - bzw. Sulfon- und Carbonsäure -funktionalisierter Polysiloxane und der Untersuchung dieser hinsichtlich ihrer Eignung als selbstätzendes Adhäsivmaterial. N2 - The focus of this dissertation is the synthesis and characterization of sulfonic or, respectively sulfonic and carbonic acid functionalized polysiloxanes for dental self -etching adhesives. The primary aim of dental adhesives is to provide a strong and long term stable adhesion to both the composite filling and the dental hard tissue. In addition to withstand mechanical forces a good adhesive should be able to prevent microleakage along the margins, possess a low toxicity and should be easy to use. Conventional dental adhesives based on organic monomer systems are not able to fulfill the requirements sufficiently. Currently used self - etching adhesives contain mostly phosphoric and phosphonic acid functionalized monomers, whose main problem is an insufficient corrosive property on dentin. However, the application of monomers containing stronger acidic groups, for example sulfonic acid, only concerns 2-acrylamidoethylpropane sulfonic acid so far. In this work new sulfonic acid functionalized inorganic - organic polysiloxanes were synthesized and the desired compounds analyzed with regards to their polymerization behavior, their corrosive properties on dental enamel and their bond strengths. KW - Funktionelle Monomere KW - Siloxane KW - Hybridwerkstoff KW - Adhäsive Restauration KW - Hybridmaterial KW - Dentaladhäsiv KW - Polysiloxane KW - dental adhesiv KW - polysiloxane Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-74989 ER - TY - THES A1 - Spatz, Kerstin T1 - Mechanische und rheologische Eigenschaften von Calciumphosphat-Zementen T1 - Mechanical and rheological properties of calcium phosphate cements N2 - Zur Erhöhung der mechanischen Stabilität mineralischer Knochenzemente aus Calciumorthophosphaten (CPC) wurde in einem TTCP/DCPA-System das Zementedukt TTCP mit verschiedenen biokompatiblen Oxiden (SiO2, TiO2, ZrO2) während des Herstellungsprozesses dotiert. Dies führte zur Bildung von Calciummetallaten und einer Herabsetzung der Löslichkeit der TTCP-Komponente des Zements. Gegenüber einem oxidfreien Zement konnte die Druckfestigkeit von 65 MPa auf 80 MPa (SiO2) bzw. 100 MPa (TiO2) gesteigert werden. In einem zweiten Ansatz zur Verbesserung der Injizierbarkeit wurden die Wechselwirkungen der Partikeloberflächen mit der flüssigen Zementphase betrachtet. Durch biokompatible Additive sollte eine repulsive elektrostatische Wechselwirkung eingestellt werden, um Partikelagglomerate effektiv zu dispergieren und eine verflüssigende Wirkung zu erreichen. Die Injizierbarkeit eines TTCP/DCPA-Zements durch eine Kanüle mit 800 µm Durchmesser konnte durch die Verwendung von 500 mM tri-Natriumzitrat-Lösung aufgrund einer deutlichen Herabsetzung der Viskosität der Zementpaste signifikant gesteigert werden (>95%, P/L 3,3/1, Kraftaufwand 20 N). Abschließend wurde der Einfluss der Partikelgrößenverteilung auf die Festigkeit und Injizierbarkeit einer auf monomodaler Partikelgrößenverteilung basierten Zementmatrix untersucht. Hierzu wurden einem mechanisch aktivierten a-TCP-System unreaktive, feinkörnige Füllstoffpopulationen (TiO2, CaHPO4, CaCO3) zugesetzt und systematisch deren Effekt in Verbindung mit einer Partikelaufladung durch tri-Natriumzitrat auf die rheologischen und mechanischen Eigenschaften untersucht. Erst die Kombination einer bimodalen Partikelgrößenverteilung mit tri-Natriumzitrat-Lösung führte zu einer starken Erniedrigung der Viskosität, damit zur nahezu vollständigen Injizierbarkeit der Zemente und einer teilweise signifikanten Steigerung der mechanischen Festigkeiten (z.B. 72 MPa reiner a-TCP-Zement auf 142 MPa mit Zusatz von CaHPO4). N2 - An improvement of the mechanical strength of calcium phosphate bone cements in combination with a lower cement paste viscosity for better injectability was investigated. A first approach to improve the mechanical stability consisted in adding several biocompatible oxides (SiO2, TiO2, ZrO2) during the fabrication process of tetracalcium phosphate (TTCP). The formation of calcium metallates led to a decrease of the solubility of the oxide doped tetracalcium phosphates. The cements based on tetracalcium phosphates mixed with SiO2 and TiO2 exhibit a significant increase of the compressive strengths (65 MPa of pure cement up to 80 MPa (SiO2) and 100 MPa (TiO2)). A second approach to decrease the viscosity of CPC pastes considered the interactions between the particle surfaces and the liquid cement phase. To disperse agglomerates and improve the injection properties of CPC, biocompatible components were added to the liquid phase. As a result the injection properties of the TTCP/DCPA cement improved significantly. The use of 500 mM trisodium citrate solution as liquid phase changed the viscosity of the cement paste to a point, where complete injectability (> 95%) through an 800 mm diameter hypodermic needle could be achieved at low loads (20 N). In order to transfer the results of a multi-constituent cement to a single reactive component cement, different fine-particle-sized fillers were added to mechanically activated, monomodal α-tricalcium phosphate (α-TCP) cement. The inert fillers dicalcium phosphate anhydrous (DCPA), titanium dioxide (TiO2) and calcium carbonate (CC) were added to the α-TCP-matrix in different concentrations. For an effective ionic modification a 500 mM trisodium citrate solution was used as liquid phase as in the aforementioned TTCP/DCPA cement system. Only the combination of a bimodal particle size distribution and trisodium citrate solution led to a nearly complete injectability and a significantly increase of the mechanical stability of CPC. KW - Biomaterial KW - Knochenzement KW - Calciumphosphate KW - Implantatwerkstoff KW - Rheologie KW - Calciumphosphat KW - calcium phosphate KW - injectability KW - zetapotential KW - mechanical properties KW - tricalcium phosphate KW - Rheologie KW - Zetapotential KW - mechanische Eigenschaften Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-124860 ER - TY - THES A1 - Beyer, Matthias T1 - Untersuchungen zu photovernetzbaren und biokompatiblen (Hybrid-)Polymeren T1 - Investigations of photo-curable and biocompatible (hybrid) polymers N2 - Die Arbeit beschäftigte sich mit Untersuchungen zu photovernetzbaren und –strukturierbaren (Hybrid-)Polymeren, um Grundlagen für die Herstellung von Trägergerüststrukturen (Scaffolds) auf Basis photovernetzbarer (Hybrid-)Polymere zu legen und damit in der Zukunft patientenindividuelle medizinische Werkstücke, die beliebig durch Zwei-Photonen-Absorptionsprozesse in drei Dimensionen strukturierbar sind, für die Regenerative Medizin zu ermöglichen. Dafür wurden zunächst die zum Teil in der Literatur unbekannten unterschiedlichen Monomere Acr-1, MAcr-2, Acr-3, MAcr-4 und DiMAcr-5 synthetisiert. Dabei handelt es sich um einfache und gut vergleichbare organische (Meth-)Acrylat-Monomere, die mono- bzw. difunktional in ihren photochemisch reaktiven Gruppen sind. Die synthetisierten organischen Monomere Acr-3, MAcr-4 und DiMAcr-5 wurden in verschiedenen Verhältnissen mit dem anorganisch-organischen Methacrylat-basierten Hybridpolymers ORMOCER® I kombiniert. Die (Co-)Polymerisation der unterschiedlichen Formulierungen wurde in situ mittels UV-DSC-Untersuchung verfolgt. Dabei wurden bei diesen Untersuchungen zum Teil deutliche Unterschiede im Reaktionsverlauf der einzelnen Materialformulierungen festgestellt. So konnten zum Beispiel bei Monomermischungen ein schnellerer Polymerisationsverlauf sowie eine höhere maximale Polymerisationsrate als bei den jeweiligen Einzelkomponenten beobachtet werden (Synergieeffekt). Diese Beobachtungen wurden anhand der Monomerstruktur (unterschiedliche Diffusionsfähigkeiten im vergelten, aber noch nicht erstarrten System durch Mono- bzw. Difunktionalität) und der Art der funktionellen Gruppe (Acrylat- bzw. Methacrylatgruppe) erklärt. Weiterhin wurden der Einfluss des verwendeten Photoinitiators und dessen eingesetzte Konzentration auf die photochemisch-induzierte Copolymerisation eines ausgewählten Systems beleuchtet. Dazu wurden verschiedene Einflussfaktoren der Initiation betrachtet. Neben der eingesetzten Initiatorkonzentration spielen auch die Absorptionseigenschaften, die umgebende Matrix und die Initiatoreffizienz eine große Rolle für den Reaktionsverlauf der photochemischen Vernetzung. Weiterhin wurden die Photoinitiatoren in unterschiedlichen Konzentrationen eingesetzt, um die dadurch induzierte Veränderung des Reaktionsverlaufs zu betrachten. Aus den Einflüssen auf die Reaktionsverläufe konnte geschlossen werden, dass diese sowie auch die maximale Polymerisationsrate RP,max und damit die Reaktionskinetik nicht in jedem Fall linear mit der Initiatorkonzentration zunehmen muss. Erste generelle 2PP-Strukturierungen wurden zudem an ausgewählten Material-formulierungen durchgeführt. Dabei zeigte sich, dass alle Formulierungen bei bestimmten Parameterkombinationen aus Laserleistung und Schreibgeschwindigkeit mittels 2PP strukturiert werden konnten. Außerdem wurden bei den verschiedenen Formulierungen bei gleicher Parameterkombination unterschiedliche Strukturbreiten und damit erstmalig unterschiedliche Strukturvolumina beobachtet. Diese unterschiedlichen Volumina konnten erstmalig mit den unterschiedlichen Reaktionsverläufen der Materialformulierungen korreliert werden. Dabei zeigte sich, dass das chemische Wechselwirkungsvolumen von der Funktionalität der eingesetzten Materialkomponenten abhängig ist, da davon der Grad an Quervernetzung abhängt, der bestimmt, ob ausreichend vernetzte Voxel und Strukturen entstehen, die durch einen Entwicklungsschritt nicht mehr entfernt werden. Im zweiten Teil der Arbeit wurde ein biokompatibles und photostrukturierbares Hybridpolymer (RENACER® MB-I) entwickelt, welches mittels 2PP strukturiert werden konnte, was anhand kleiner wie auch großer Scaffolds mit dem Material demonstriert wurde. Dazu wurde das kommerziell erhältliche Alkoxysilan-Molekül O-(Methacryloxyethyl)-N-(triethoxysilylpropyl)urethan als Precursor verwendet. Durch eine bewusst unvollständige Hydrolyse- und Kondensationsreaktion konnte aus dem Precursorsilan ein Hybridpolymerharz hergestellt werden, welches anorganisch vorverknüpft war. Weiterhin wies es sowohl als Volumenpolymer, als auch in Form von Scaffold-Strukturen eine sehr gute Biokompatibilität auf. Um zu untersuchen, ob die im Hybridpolymer enthaltenen prinzipiell degradierbaren Gruppen unter physiologischen Bedingungen tatsächlich degradieren und Teile aus dem Polymerverband herausgelöst werden können, wurde ein selbstentwickeltes Verfahren für stationäre Degradations-untersuchungen in phosphat-gepufferter Saline (PBS, pH = 7,4) verwendet. Die durch die photochemische Polymerisation neu entstandenen Ketten besaßen ihrer Natur gemäß keine hydrolysierbaren Einheiten, weshalb das Hybridpolymer nicht vollständig degradieren kann. Es konnte jedoch ein prinzipieller Zugang zu Gerüstträgerstrukturen auf Basis photovernetzbarer Polymere für die Regenerative Medizin geschaffen werden. N2 - The objective was the investigation of photo-curable and patternable (hybrid) polymers for applications in regenerative medicine, in order to explore basic principles for scaffold fabrication by two-photon polymerization. This would enable patient-individual medical implants. As model systems for subsequent investigations, the monomers Acr-1, MAcr-2, Acr-3, MAcr-4, and DiMAcr-5 were synthesized. These compounds are well comparable organic (meth)acrylate monomers with a functionality of one and two, respectively. The monomers Acr-3, MAcr-4, and DiMAcr-5 were combined with a well-known methacrylate-based inorganic-organic hybrid polymer ORMOCER® I in different molar ratios. After preparation of the monomers and their formulations with ORMOCER® I introducing defined amounts of photoinitiator Irgacure® 369 into the material systems, the materials’ reaction was monitored in situ by photo-DSC investigations. In particular, the effect of the different monomer ratios on the copolymerization behavior was studied in more detail. A higher maximum polymerization rate and, therewith, a higher reaction speed was found for all formulations of monomer mixtures in contrast to the corresponding individual monomers (synergy effect). Moreover, by comparing the various organic monomers, considerable differences could be identified in between acrylates and methacrylates as well as for the mono- and difunctional species. These effects were explained by means of the type of their photochemically organically cross-linkable functional groups and thus their resulting reactivity as well as by the monomer structure and functionality itself, resulting in different diffusion abilities of mono-, oligo- and polymeric species within gelled systems. Furthermore, the influence of several photoinitiators and the initiator concentration on the photochemically induced copolymerization was investigated. Besides the initiator concentration, also the initiators’ absorption properties, the resin matrix and the initiators’ efficiency play an important role for the reaction profile of the photochemical cross-linking. All different photoinitiators were introduced into the model system in three different concentrations to explore the induced alterations on the reaction profile. For some of the investigated initiators, the maximum polymerization rate RP,max and, therewith, the overall reaction kinetics increased with increasing photoinitiator concentration, but for other initiators, the maximum polymerization rate RP,max was lowered at increased initiator concentrations. Thus, a general relationship between the photoinitiator concentration and the maximum polymerization rate RP,max could not be identified. First structures were generated out of selected mixtures by two-photon polymerization in order to demonstrate the novel materials’ ability of being patterned in three dimensions. Three dimensional structures were generated with specific parameter combinations of laser power and writing speed, whereas each parameter set corresponds to an individual exposure dose deposited in the materials’ volume. In particular, different structure widths were observed for different material formulations fabricated with the same parameter sets. Thus, it was possible for the first time to experimentally observe different chemical interaction volumes. These interaction volumes were correlated to the different reaction profiles of the material formulations, which were received via 1PP photo-DSC measurements. It was shown that the structure volume depends on the functionality of the employed monomers, because their degree of cross-linking depends on their functionality. The degree of cross-linking which results upon polymerization determines, whether a structure maintains stable during the subsequent development process. In the second part of this work, a biocompatible and photo-patternable hybrid material was developed. Commercially available O-(methacryloxyethyl)-N-(triethoxysilylpropyl)-urethane was chosen for an intentional incomplete hydrolysis and condensation reaction in order to receive a RENACER® resin, which includes functional groups for subsequent organic cross-linking. This material showed a very good patterning performance, which was demonstrated by a series of structures and scaffolds. The material yields a good biocompatibility. In order to investigate, whether the hydrolysable functional groups within the hybrid polymer actually degrade under physiological conditions, a procedure routine for stationary degradation studies in phosphate-buffered saline (PBS) was developed. The carbon chain generated through photochemical cross-linking, has no hydrolyzable groups and naturally cannot be degraded, resulting in a hybrid polymer which is not completely degradable. However, a principal access to scaffolds for regenerative medicine on the basis of photo-curable polymers was accomplished which was the purpose of this work. KW - Photopolymerisation KW - Zwei-Photonen-Polymerisation KW - Copolymerisation KW - Reaktionskinetik KW - Biokompatibilität KW - Photo-DSC KW - Kinetik Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-97131 ER - TY - JOUR A1 - Luxenhofer, Robert A1 - Fetsch, Corinna T1 - Thermal Properties of Aliphatic Polypeptoids JF - Polymers N2 - A series of polypeptoid homopolymers bearing short (C1–C5) side chains of degrees of polymerization of 10–100 are studied with respect to thermal stability, glass transition and melting points. Thermogravimetric analysis of polypeptoids suggests stability to >200 °C. The study of the glass transition temperatures by differential scanning calorimetry revealed two dependencies. On the one hand an extension of the side chain by constant degree of polymerization decrease the glass transition temperatures (Tg) and on the other hand a raise of the degree of polymerization by constant side chain length leads to an increase of the Tg to a constant value. Melting points were observed for polypeptoids with a side chain comprising not less than three methyl carbon atoms. X-ray diffraction of polysarcosine and poly(N-ethylglycine) corroborates the observed lack of melting points and thus, their amorphous nature. Diffractograms of the other investigated polypeptoids imply that crystalline domains exist in the polymer powder. KW - peptoid KW - biomaterials KW - glass transition temperature KW - DSC KW - TGA KW - XRD Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-96333 ER - TY - THES A1 - Mandel, Karl T1 - Synthesis and Characterisation of Superparamagnetic Nanocomposite Particles for Water Purification and Resources Recovery T1 - Synthese und Charakterisierung von superparamagnetischen Nanokompositpartikeln zur Wasserreinigung und Wertstoffrückgewinnung N2 - Superparamagnetic nanocomposite microparticles, compromised of magnetite nanoparticles in a silica matrix, have been synthesised and surface-modified to act as adsorbers for substances (e.g. toxic heavy metals or valuable resources) dissolved in fluids like water. The particles can be used for a magnetic-extraction-assisted separation process of these target substances which thereby can be recovered from the fluid. N2 - In der vorliegenden Arbeit wurden superparamagnetische Nanokomposit-Mikropartikel, bestehend aus Magnetitnanopartikeln in einer Silica-Matrix, hergestellt. Die Oberfläche der Partikel wurde modifiziert, so dass die Partikel als Adsorber für gelöste Substanzen (z.B. giftige Schwermetalle oder Wertstoffe) in Fluiden wie z.B. Wasser eingesetzt werden können. Mit Hilfe der Partikel kann eine Abtrennung und damit Rückgewinnung der Zielstoffe auf Basis eines Magnetseparationsprozesses durchgeführt werden. KW - Magnetisches Trennverfahren KW - Superparamagnetismus KW - Recycling KW - Wasserreinigung KW - Eisenoxide KW - Siliciumdioxid KW - Superparamagnetismus KW - Nano KW - Wertstoffrückgewinnung KW - Magnetseparation KW - superparamagnetism KW - nano KW - water purification KW - resources recovery KW - magnetic separation KW - Nanotechnologie KW - Synthese KW - Magnetismus Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-81208 ER - TY - THES A1 - Kimmig, Stefan T1 - Herstellung und Charakterisierung von SiC-Faser-verstärktem Kupfer zur Anwendung in Hochleistungswärmesenken T1 - Manufacturing and characterisation of SiC-fibre-reinforced copper in heat sink applications N2 - Die Wandmaterialien innerhalb des Plasmagefäßes zukünftiger Fusionsreaktoren sind teilweise extremen thermischen und mechanischen Belastungen ausgesetzt. Der thermisch höchstbelastete Bereich der Wand des Torusgefäßes ist der Divertor. Hier werden die anfallende Fusionsasche (Helium) und erodierte Wandpartikel aus dem Plasma entfernt, wodurch aufgrund erhöhter Teilchen-Wand-Interaktion Wärmeflüsse von bis zu 15 MW/m² erreicht werden. Wolfram gilt momentan als ideales Wandmaterial mit direktem Plasmakontakt (Plasma-Facing-Material, PFM) für diese Beanspruchungen. Unterhalb des PFM muss die Wärme möglichst effizient in das Kühlmedium übertragen werden. Im zukünftigen Experimentalreaktor ITER wird dafür eine Kupferlegierung (CuCrZr) verwendet, welche eine hohe Wärmeleitfähigkeit besitzt und für Temperaturen von bis zu 350°C unter fusionsrelevanten Bedingungen einsetzbar ist. In dieser Konfiguration kann ITER mit einer Kühlmitteltemperatur von 150°C betrieben werden. Zur kommerziellen Energiegewinnung ist dies unzureichend, da die thermische Effizienz durch eine deutliche Anhebung der Kühlmitteltemperatur verbessert werden muss. Wird der konventionelle Ansatz einer Wasserkühlung zu Grunde gelegt, ist das Ziel die Kühlmitteltemperatur auf mindestens 300°C anzuheben. In der Folge ist CuCrZr als Wärmesenkenmaterial nicht mehr einsetzbar, da verstärkte Alterung und Festigkeitsverlust im Material auftritt. Zusätzlich vergrößern sich die thermisch induzierten Spannungen in der Komponente mit höheren Temperaturen, durch unterschiedlich große thermische Ausdehnungskoeffizienten der beteiligten Materialien. Für höhere Temperaturen stellt faserverstärktes Kupfer eine mögliche Alternative dar. Die Kombination der hohen Wärmeleitfähigkeit der Kupfermatrix mit der hohen Steifigkeit und Festigkeit von Siliziumcarbidfasern soll die nötigen thermischen und mechanischen Eigenschaften des Wärmesenkenmaterials auch für Temperaturen über 350°C gewährleisten. Im Rahmen dieser Arbeit wurden zwei unterschiedlich hergestellte SiC-Verstärkungsfasertypen hinsichtlich ihrer Eignung für die Herstellung eines Kupfer-Matrix-Komposits (CuMMC) untersucht. Die Zielstellung für das CuMMC beinhaltet eine Festigkeit von 300 MPa bei 300°C sowie eine möglichst hohe Wärmeleitfähigkeit von über 200 W m-1 K-1. Beide Parameter werden stark von der Faserfestigkeit und der Anbindung zwischen Faser und Matrix beeinflusst. Die Wärmeleitfähigkeit durch das CuMMC wird von der Kupfermatrix dominiert, wodurch geringere Faservolumenanteile von Vorteil sind. Höhere Faserfestigkeit erfordert geringere Faseranteile zum Erreichen mechanischer Vorgaben, womit die erzielbare Wärmeleitfähigkeit des CuMMCs steigt. Die Faserfestigkeit wird durch Einzel-Faser- Zugversuche validiert. Darüber hinaus ist die Anbindung zwischen Faser und Matrix essentiell, um die optimale Verstärkungswirkung durch die Fasern im CuMMC zu erzielen. Zur Faser-Matrix-Anbindung werden für jeden Fasertyp unterschiedliche Zwischenschichtsysteme verwendet, die anschließend durch Einzelfaser-Push-Out-Versuche validiert werden. Sind die Voraussetzungen von Faserfestigkeit und Anbindung für einen Fasertyp erfüllt, wird dieser für die Herstellung eines unidirektional verstärkten CuMMCs verwendet, welches bezüglich seiner mechanischen und thermischen Eigenschaften charakterisiert wird. Die mechanische Charakterisierung des CuMMCs erfolgt durch Zugversuche und dehnungsgeregelte, zyklische Versuche, wobei der Fokus neben der Festigkeit auf der Plastifizierung, Verfestigung und Schädigung innerhalb des CuMMCs liegt. Die thermische Charakterisierung erfolgt anhand der Wärmeleitfähigkeitsbestimmung sowohl parallel, als auch transversal zur Faserrichtung. Die mechanischen und thermischen Eigenschaften werden in Abhängigkeit von Faservolumenanteil und Temperatur untersucht. Um den Einfluss von längeren Betriebsphasen unter hoher thermischer Belastung analysieren zu können, wird das CuMMC bei 550°C für 400 h ausgelagert und anschließend wiederum mittels Vergleich seiner mechanischen und thermischen Eigenschaften auf mögliche Schädigungen untersucht. Zur Begutachtung von Schliff- und Bruchflächen zur Schadensanalyse stehen als bildgebende Untersuchungsmethoden neben Lichtmikroskopen ebenso Rasterelektronenmikroskope (REM) zur Verfügung. N2 - The wall materials in future fusion reactors will be operating under extreme thermal and mechanical load conditions. The divertor region of such a device is the most severely loaded component. This part is exposed to heat fluxes of up to 15 MW m-² due to the impinging plasma particle flux. Tungsten is currently considered as the best choice for the plasmafacing- materials (PFM) in the divertor region. An efficient heat sink material is required underneath the PFM for sufficient heat transfer to the cooling channels. In the research reactor ITER a copper alloy (CuCrZr) is foreseen as heat sink material, which is able to withstand temperatures of up to 350°C, corresponding to a water coolant temperature of 150°C. For the commercial use of fusion energy an increase of the thermal efficiency is necessary by increasing the coolant temperature to over 300°C. This will cause higher stresses in the connection area between PFM and the heat sink due to different coefficients of thermal expansion combined with higher temperatures. The mechanical properties of CuCrZr are insufficient for these conditions and fibre reinforced copper metal matrix composites (CuMMC) are considered as an alternative material to strengthen the critical connection area between the heat sink and the PFM. The composite should combine the high heat conductivity of a copper matrix with the high stiffness and mechanical strength of silicon-carbide fibres (SiC-fibres). During this investigation SiC-fibres of two different production principles were studied regarding their usage for the manufacturing of a CuMMC. The main goals for the CuMMC are a tensile strength of 300 MPa combined with a heat conductivity of more than 200 W m-1 K-1. Both of these parameters are affected by the single fibre tensile strength and by the bonding between the fibres and the copper matrix. The achievable heat conductivity in the CuMMC depends on the fibre volume ratio within the composite. Higher fibre strength reduces the necessary fibre volume ratio and hence increases the heat conductivity of the CuMMC. The fibre strength was validated by single fibre tension tests. Furthermore, a good bonding between fibre and matrix is necessary to optimize the fibre reinforcement, which is based on load transfer between fibre and matrix. Therefore, both fibre types were coated with interlayer systems and the effectiveness of the bonding was validated by single fibre push-outtests. For those cases where fibre strength and bonding were sufficient, a unidirectional fibre reinforced CuMMC was manufactured, who’s mechanical and thermal properties were then characterised. The mechanical tests included tensile tests and strain-controlled cycling tests which gave information about strength, plasticity, hardening and the effect of damage within the CuMMC. To verify that the CuMMC heat sink material achieves the thermal requirements, heat conductivity measurements parallel and perpendicular to the fibre direction were performed. These characterizations were done as a function of fibre volume fraction in the CuMMC and temperature. To investigate the influence of long term exposure to operation temperatures, a heat treatment was carried out for 400 h at 550°C and the mechanical and thermal properties were compared to their initial values. Different optical microscopes and scanning electron microscopes (REM) were used for the analysis of crack surfaces and grindings. For the engineering design of divertor components numerical models of the used material are required. These models need to be developed by adjusting their input parameters to fit experimental results. To that end, strain-controlled cycling tests allowed the analysis of the copper matrix hardening behaviour. This is necessary to understand stress development during operational load cycles of the CuMMC. The comparison of room temperature tests with 300°C tests showed the effects of fabrication-induced residual stress in the CuMMC. KW - Kupfer KW - Faserverstärkung KW - Metallmatrix-Verbundwerkstoff KW - Kühlkörper KW - Komposite KW - copper KW - fibre-reinforcement KW - SiC KW - heat sink KW - metall-matrix-composite KW - Siliciumcarbid KW - MMC Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-85123 ER - TY - THES A1 - Wagenhöfer, Julian T1 - Mikro- und mesoporöse Silicate als Wirkstoffspeichersysteme T1 - Micro and mesoporous silica for drug-delivery-systems N2 - Mesoporöse Silica-Materialien (MSM) und mikroporöse Zeolithe besitzen große innere Oberflächen und eine damit verbundene hohe Speicherkapazität von verschiedenen Molekülen. Auf Grund dieser Eigenschaften stehen poröse, silicatische Materialien seit etwa 10 Jahren im Focus der Entwicklung neuartiger Wirkstoffspeichersysteme (WSS). Die innerhalb dieser Thematik veröffentlichten wissenschaftlichen Arbeiten konnten die Fragestellungen nach dem exakten Mechanismus der Wirkstoffspeicherung und Wiederfreisetzung bisher nicht komplett beantworten. Die vorliegende Arbeit beschäftigt sich im Besonderen mit der Beladung und Abgabe des Lokalanästhetikum Lidocain-Hydrochlorid (LidHCl) in bekannten MSM wie SBA15, MCM41 oder HMS, sowie in unterschiedlich modifizierten Zeolithen vom Typ FAU und BEA. Zusätzlich wurde der Einfluss von organischen Ankergruppen innerhalb der Porenstruktur von SBA15 auf dessen Sorptions-eigenschaften hin untersucht. Ziel der Promotionsarbeit ist die Aufklärung des Speicher- und Freisetzungs-mechanismus dieses speziellen Speichersystems. Dazu wurden zunächst detaillierte Analysen der reinen und der mit Wirkstoff beladenen Matrizes via N2-Sorption (BET-, BJH-, t-plot-Methode), XRD, SAXS, DSC und TG durchgeführt. Außerdem wurden grafische Profile erstellt, die das Verhältnis der ad- bzw. desorbierten Wirkstoffmengen gegen die bei der Beladung eingesetzten Wirkstoffkonzentrationen (Speicherprofil) bzw. gegen die bei der Wiederfreisetzung verstrichene Zeit (Freisetzungsprofil) wiedergeben. Durch die Kombination dieser Untersuchungsmethoden konnte der jeweilige Sorptionsmechanismus, sowie der Speicherort der Wirkstoffmoleküle innerhalb der ausgewählten Matrix erfasst werden. Der Vergleich der verschiedenen, hier untersuchten Speichersysteme zeigt, dass neben der Porengröße, die Art der Adsorbens-Adsorbat-Wechselwirkung, aber auch die Stabilität der Porenstruktur einen großen Einfluss auf die Sorption von Molekülen nimmt. N2 - Mesoporous Silica Materials (MSM) and microporous zeolites show high inner surfaces and high storage capacities for the delivery of molecules. As a result of these characteristics porous silica materials are in the focus of new Drug Delivery Systems (DDS´s) for about ten years. Scientific work on this topic could not totally clarify the mechanism of drug delivery and drug release up to now. This work deals particularly with the storage and release of the local anesthetic lidocaine hydrochloride (LidHCl) both in well-known MSM like SBA15, MCM41 or HMS and in modified zeolite type FAU or BEA. In addition the influence of organic anchor groups in modified SBA15 on the sorption characteristic was examined. The aim of this PhD thesis is the clarification of the delivery mechanism of this special DDS. Initially detailed analysis of pure and drug-loaded matrices were done by N2 Sorption (BET-, BJH-, t-plot-method), XRD, SAXS, DSC and TGA. Furthermore graphic accounts illustrate the relationship between the adsorbed drug amount and the drug concentration used during the loading (sorption profile) or released drug amount and the elapsed time (release profile). Delivery mechanisms and sorption spots of the drug molecules inside the selected adsorbents were formulated by the combination of these characterization methods. The comparison of the used DDS´s shows in detail that the sorption of molecules in porous silicates is extra-ordinary influenced by pore size, drug-adsorbens interaction and pore structure stability of the matrix. KW - Silicate KW - Zeolith KW - Lidocain KW - Wirkstofffreisetzung KW - Mikroporosität KW - Freisetzungskinetik KW - Wirkstoffspeichersystem KW - Speicherprofil KW - Nanoporöser Stoff KW - Mesoporous Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-103848 ER - TY - JOUR A1 - Schulz, Anita A1 - Jaksch, Sebastian A1 - Schubel, Rene A1 - Wegener, Erik A1 - Di, Zhenyu A1 - Han, Yingchao A1 - Meister, Annette A1 - Kressler, Jörg A1 - Kabanov, Alexander V. A1 - Luxenhofer, Robert A1 - Papadakis, Christine M. A1 - Jordan, Rainer T1 - Drug-Induced Morphology Switch in Drug Delivery Systems Based on Poly(2-oxazoline)s JF - ACS Nano N2 - Defined aggregates of polymers such as polymeric micelles are of great importance in the development of pharmaceutical formulations. The amount of drug that can be formulated by a drug delivery system is an important issue, and most drug delivery systems suffer from their relatively low drug-loading capacity. However, as the loading capacities increase, i.e., promoted by good drug–polymer interactions, the drug may affect the morphology and stability of the micellar system. We investigated this effect in a prominent system with very high capacity for hydrophobic drugs and found extraordinary stability as well as a profound morphology change upon incorporation of paclitaxel into micelles of amphiphilic ABA poly(2-oxazoline) triblock copolymers. The hydrophilic blocks A comprised poly(2-methyl-2-oxazoline), while the middle blocks B were either just barely hydrophobic poly(2-n-butyl-2-oxazoline) or highly hydrophobic poly(2-n-nonyl-2-oxazoline). The aggregation behavior of both polymers and their formulations with varying paclitaxel contents were investigated by means of dynamic light scattering, atomic force microscopy, (cryogenic) transmission electron microscopy, and small-angle neutron scattering. While without drug, wormlike micelles were present, after incorporation of small amounts of drugs only spherical morphologies remained. Furthermore, the much more hydrophobic poly(2-n-nonyl-2-oxazoline)-containing triblock copolymer exhibited only half the capacity for paclitaxel than the poly(2-n-butyl-2-oxazoline)-containing copolymer along with a lower stability. In the latter, contents of paclitaxel of 8 wt % or higher resulted in a raspberry-like micellar core. KW - amphiphilic poly(2-oxazoline)s KW - paclitaxel KW - drug delivery KW - rod-to-sphere transition Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-120766 N1 - This is an open access article published under an ACS AuthorChoice License (http://pubs.acs.org/page/policy/authorchoice_termsofuse.html), which permits copying and redistribution of the article or any adaptations for non-commercial purposes. VL - 8 IS - 3 ER - TY - THES A1 - Kocic, Nikola T1 - Bestimmung des Keimbildungsexponenten für die Kristallisation von Polymeren durch nicht-isotherme DSC-Analysen T1 - Determination of the nucleation parameter for the crystallization of polymers by non-isothermal DSC-analysis N2 - Thermoplastische Kunststoffe (sog. Thermoplaste) lassen sich in einem be-stimmten Temperaturbereich beliebig oft schmelzen und in einer gewünschten Form erstarren. Grundvoraussetzung für eine bestimmte Anwendung eines thermoplastischen Bauteils sind die Gebrauchseigenschaften des Materials, die im Wesentlichen vom Ablauf der Erstarrung abhängen. Die Moleküle einiger Thermoplaste können bei der Erstarrung geordnete kristalline Bereiche bilden. Dies sind die sog. teilkristallinen Kunststoffe, deren Erstarrungsprozess Kristallisation genannt wird. Die dabei entstehenden Kristallstrukturen werden zusammen mit deren Charakteristiken allgemein als Morphologie der teilkristallinen Kunststoffe bezeichnet. Die Morphologie hat einen signifikanten Einfluss auf die mechanischen, thermischen und optischen Eigenschaften des Materials. Dementsprechend stellen Kenntnisse über die Kristallisation eine wertvolle Hilfe bei der Vorhersage der Gebrauchseigenschaften eines teilkristallinen Kunststoffs dar. Um die Kristallisation zu starten, muss zunächst eine Energiebarriere überwunden werden, die an erster Stelle vom molekularen Aufbau des Kunststoffs abhängt. Somit weisen beispielsweise Kunststoffe mit linearen, regelmäßigen Molekülen und kleinen Seitengruppen eine niedrigere Energiebarriere und aus diesem Grund eine starke Neigung zur Kristallisation auf. Einige Zusatzstoffe wie z. B. unterschiedliche Additive, Farbstoffe oder Füllstoffe können die Energiebarriere und infolgedessen die Kristallisation eines teilkristallinen Kunststoffs wesentlich beeinflussen. Das Ziel dieser Dissertation war es, ein bestehendes Kristallisationsmodell zu erweitern und es an gefüllte oder additivmodifizierte teilkristalline Kunststoffe anzupassen. Das erweiterte Modell soll die Ermittlung eines Kristallisationspa-rameters, des sog. Keimbildungsexponenten, eines gefüllten oder additivmodifizierten teilkristallinen Kunststoffs bei der nicht-isothermen Kristallisation ermöglichen. Der Keimbildungsexponent ist mit der erwähnten Energiebarriere eng verbunden und bestimmt somit den Ablauf des Kristallisationsprozesses bzw. die daraus folgende Morphologie. Ein wesentlicher Schwerpunkt der Arbeit lag darin, die vorgeschlagene Modellerweiterung bei verschiedenen Abkühlgeschwindigkeiten zu überprüfen. Im Anschluss sollten die Beziehungen zwischen den berechneten Keimbildungsexponenten und experimentell ermittelten me-chanischen Eigenschaften (E-Modul, Streckspannung und Schlagzähigkeit) überprüft werden. Für die Untersuchungen wurden drei verschiedene Polymersysteme verwendet: PP / Talkum, HDPE / Talkum sowie PA6 / Bentonit. Hierbei weist der Füllstoff eine stark positive, schwach positive bzw. inhibierende Wirkung auf die Kristallisation der entsprechenden Polymermatrix auf. Hinsichtlich reiner Polymere wurde eine gute Übereinstimmung zwischen den ermittelten und Literaturwerten des Keimbildungsexponenten festgestellt. Die Zugabe von positiv wirkendem Talkum in PP bzw. HDPE führt zu einer Abnah-me des Keimbildungsexponenten, was zu dickeren Kristallen des jeweiligen Kunststoffs führte. Im Gegensatz dazu bewirkte die Bentonitzugabe einen zu-nehmenden Keimbildungsexponenten, was anschließend dünnere PA6-Kristalle zur Folge hat. Die durchgeführten Untersuchungen zeigen außerdem, dass die Füllstoffpartikelgröße einen ausgeprägten Einfluss auf den ermittelten Keimbildungsexponenten hat. Weiterhin wurde festgestellt, dass der ermittelte Keimbildungsexponent durch die (DSC)-Abkühlgeschwindigkeit beeinflusst wird. Es wurde ferner gezeigt, dass sich dieser Einfluss ab einer bestimmten Abkühlgeschwindigkeit (20 K/min im Falle des PP und HDPE bzw. 15 K/min im Falle des PA6) nicht mehr ändert, was zu einem konstanten Keimbildungsexponenten führt. Um den Einfluss der Abkühlgeschwindigkeit auf die modellierte Größe zu berücksichtigen, sind weitere Untersuchungen nötig. Die Ergebnisse der Arbeit zeigen weiterhin, dass der berechnete Keimbildungsexponent mit den experimentell ermittelten Werten für E-Modul, Streckspannung und Charpy-Schlagzähigkeit bei talkumgefülltem PP gut korreliert. Solche Korrelationen wurden jedoch bei den HDPE- und PA6-Proben nicht gefunden. Der Grund hierfür könnte eine ausgeprägte Orientierung der HDPE-Makromoleküle bzw. ein starker mikromechanischer Effekt des exfolierten Bentonits sein. Diese Effekte konnten im Rahmen der Arbeiten bestätigt werden. Die in dieser Arbeit erzielten Ergebnisse zeigen, dass die vorgeschlagene Mo-dellerweiterung auch bei gefüllten oder additivmodifizierten Kunststoffen zufriedenstellende Resultate liefert. Die entsprechende Berechnung erfordert dabei lediglich eine DSC-Messung, was im Vergleich zum Stand der Technik in einen niedrigeren Messaufwand resultiert. Die vorliegende Arbeit liefert daher einen signifikanten Beitrag zur Erstellung des Zusammenhangs zwischen der Kristallisation, der Morphologie und dem mechanischen Verhalten von teilkristallinen Polymeren. N2 - Thermosoftening polymers, also called thermoplastics, can be repeatedly melt-ed and solidified into a desired shape in a certain temperature range. The basic requirements for a particular application of a thermoplastic component are its functional characteristics, which significantly depend on the solidification pro-cess. The molecules of some thermoplastics can form ordered crystalline regions during the solidification process. These are so-called semi-crystalline polymers, whose solidification process is called crystallization. The resulting crystal struc-ture elements, together with their properties, are commonly referred to as the morphology of semi-crystalline polymers. The morphology has a significant in-fluence on the mechanical, thermal and optical properties of the material. Ac-cordingly, knowledge about the crystallization is a valuable aid in predicting the final properties of a semi-crystalline polymer. In order for the crystallization to start, it is necessary for an activation energy barrier to be overcome. The activation energy barrier depends on the molecular structure of the polymer. Polymers with linear, regular molecules and small side groups possess a low activation energy barrier and therefore crystallize most easily. Some ingredients, such as various additives, pigments or fillers, can significantly affect the energy barrier and consequently the crystallization of a semi-crystalline polymer. The aim of this thesis was to extend an existing crystallization model and adapt it to filled or additive-modified semi-crystalline polymers. The extended model should allow the determination of a crystallization parameter, the so-called nu-cleation parameter of filled or additive-modified semi-crystalline polymers during non-isothermal crystallization. The nucleation parameter is closely connected with the activation energy barrier and thus determines the crystallization process and consequentially the resulting morphology. An important task in this work was to verify the proposed model extension for different cooling rates. In addition, the correlations of the calculated nucleation parameter with experimentally determined mechanical properties (Young’s modulus, yield stress and impact strength) are established and discussed. In this research, three different polymer systems were used: PP / talc, HDPE / talc and PA6 / bentonite. In these three materials, the filler has a strong positive, a weak (positive) and a negative influence on the crystallization of a given polymer, respectively. A good agreement between the values of the nucleation parameter determined in this work and those found in literature was obtained as regards pure poly-mers. The addition of positive-acting talc in PP and HDPE leads to a decreased nucleation parameter, resulting in an increase of the crystal thickness of PP and HDPE. By contrast, the addition of bentonite increases the nucleation parameter of PA6 and therefore leads to a decrease in the crystal thickness of PA6. It was also shown that the filler particle size has a significant influence on the nucleation parameter. Furthermore, it was shown that the DSC cooling rate up to a certain value (20 K/min as regards PP und HDPE i.e. 15 K/min regarding PA6) has an influence on the determined nucleation parameter. Afterwards, the nucleation parameter reaches a plateau and shows no further changes with the cooling rate. To be able to add the influence of the cooling rate into the model, further studies are needed. Furthermore, it was shown that the obtained nucleation parameters correlates well with the Young modulus, yield stress and impact strength as regards PP filled with talc. In contrast to PP, such correlations were not found for HDPE and PA6 samples. The possible reason for the absence of correlations could be the orientation of the HDPE molecules, i.e. the strong reinforcing effects of the intercalated bentonite in PA6. These effects were confirmed in the scope of the work. The results obtained in this work show that the proposed model extension is applicable as regards filled semi-crystalline polymers. In comparison to the state of the art, the proposed model extension requires only a single DSC-measurement resulting in a lower measuring expenditure. Therefore, the pre-sent work provides a significant contribution to establishing the mathematical relationship between the crystallization, morphology and the mechanical behavior of semi-crystalline polymers. KW - Kristallisation KW - Polymer KW - Morphologie KW - Polymere KW - Keimbildung KW - Kalorimetrie Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-113950 ER - TY - THES A1 - Back, Franziska T1 - Herstellung SiO2-basierter nano- und mikroskaliger Strukturen via UV-Nanoimprintlithographie auf Basis hybridpolymerer Sol-Gel-Materialien T1 - Synthesis of sio2-based nano- and microscale structures by uv-based nanoimprintlithography based on hybrid sol-gel-materials N2 - Die vorliegende Arbeit beschreibt die Entwicklung von SiO2-basierten nano- und mikroskalig strukturierten Schichten, welche eine Temperaturstabilität > 500 °C sowie eine Strukturtreue > 90 % aufzeigen. Diese wurden unter Verwendung von hybridpolymeren, partikelmodifizierten Sol-Gel-Vorstufen via UV-basierter Nanoimprintlithographie (UV-NIL) hergestellt. Der Einfluss chemischer und verfahrenstechnischer Syntheseparameter auf die anorganische Netzwerkbildung der flüssigen Vorstufe (hybridpolymerer Binder), die Polymerisation und Verdichtung der hybridpolymeren Sol-Gel-Schichten während der thermischen Härtung sowie deren Strukturierung via UV-NIL wurden im Detail untersucht und die erhaltenen Zusammenhänge mit den resultierenden Materialeigenschaften korreliert. Dabei dienten die Kenntnisse hinsichtlich des Schrumpf- und Verdichtungsverhaltens von planaren Schichten als Basis für die daraus hergestellten, strukturierten Schichten. N2 - The present work describes the development of SiO2-based nano- and microstructured coatings with temperature stability > 500 °C and structure fidelity > 90 %. The coatings were produced via UV-nanoimprintlithography (UV-NIL) by using particle modified, hybrid sol-gel-precursors. The influence of synthesis chemical and process parameters on formation of inorganic network of the hybrid binder, polymerisation and densification of hybrid sol-gel-films during thermal annealing and imprinting of the hybrid sol-gel-films were investigated and correlated with resulting material properties. The results of shrinkage and densification of planar coatings were used to characterize the structured coatings. KW - Sol-Gel-Verfahren KW - Nanoprägen KW - Temperaturbeständigkeit KW - Strukturtreue KW - Hybridpolymer KW - Nanoimprint Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-107713 ER - TY - THES A1 - Collin [geb. Trötschel], Daniela T1 - Untersuchungen zu photostrukturierbaren piezo- und ferroelektrischen Dünnschichten T1 - Investigations concerning photopatternable piezo- and ferroelectrical thin-films N2 - Im Rahmen der vorliegenden Arbeit wurde untersucht, wie sich organisch polymerisierbare Titan(IV)- und Zirkonium(IV)komplexe, die bei der Synthese anorganisch-organischer Hybrid-polymere verwendet werden, in Precursor-Solen für anorganische Beschichtungen verhalten. Dabei sollte ein Konzept zur Herstellung photochemisch strukturierter, anorganischer Dünnschichten erarbeitet werden. Als Beispiel für das anorganische Dünnschichtmaterial wurde Bleizirkonattitanat (PZT) und für die polymerisierbaren Liganden Methacrylsäure gewählt. Der Schwerpunkt der Arbeit lag dabei besonders auf den Untersuchungen der photochemischen Polymerisation mittels UV-lithographischer und Mehrphotonenpolymerisation sowie der in situ Untersuchung während der Pyrolyse des polymerisierten Materials und der Reaktion zur anorganischen Dünnschicht. Der Prozess zur Herstellung photostrukturierter, anorganischer Dünnschichten kann in zwei Schritte eingeteilt werden. Nach der Synthese des Precursor-Sols erfolgten zunächst die licht-induzierte organische Polymerisation und die Entfernung der nicht polymerisierten Bereiche mit Hilfe eines Entwicklerbads. Im Anschluss daran wurden im zweiten Schritt die organischen Bestandteile durch eine thermische Behandlung entfernt und die Reaktion zum anorganischen Oxidmaterial induziert. Die homogensten Schichten wurden dabei mit einem n Butanol-basierten, methacrylat¬funktionalisierten PZT-Sol mit 25 Gew. % Feststoffgehalt auf Stahlsubstraten bei Pyrolyse¬bedingungen ab 500 bis 700 °C mit einer Heizrate von 5 K/min erreicht. An diesen Schichten konnte ferroelektrisches Verhalten nachgewiesen werden. Allerdings reichen die Eigenschaften noch nicht an in der Literatur beschrieben ferro- und piezoelektrische Dünnschichten heran, die ebenfalls aus PZT-Solen hergestellt wurden. Dies liegt zum einen an den zu geringen Schichtdicken und der damit verbundenen erhöhten Durchschlagsgefahr dieser Sol-Gel-basierten PZT-Schichten. Zum anderen reduzieren Grenzflächenreaktionen des chromhaltigen Substrats und der PZT-Solschicht zu Pb2(CrO4)O sehr drastisch die ferroelektrischen Eigenschaften, indem sich nicht-ferroelelektrische Oxidschichten mit niedrigen Permittivitäten bilden und die Beweglichkeit der Domänenwände durch Diffusion von Cr3+-Akzeptorionen in die PZT-Schicht verringert wird. Zunächst wurde die PZT-Solsynthese untersucht. Dabei konnte gezeigt werden, dass die Nebenproduktbildung von verschiedenen Estern vermieden werden kann, wenn die leicht flüchtigen Bestandteile nach der Ligandenaustauschreaktion von Alkoxid gegen Methacrylsäure bei reduziertem Druck und damit verbundenen niedrigeren Reaktionstemperaturen, erfolgte. Die Bindung der Methacrylatliganden ist in jedem Fall bidentat. Bei den n Butanol-basierten PZT-Solen konnte trotz höherer Siedetemperatur und niedrigerem Dampfdruck ein größerer Anteil an Alkohol entfernt werden, als bei n-Propanol-basierten PZT-Solen. Dies wurde auf den etwas höheren +I Effekt des n Butanols und in der Folge der bevorzugten Ligandenaustauschreaktion von Methacryl¬säure gegen den n Butanol im Vergleich zu n Propanol zurückgeführt. Die Größe der PZT-Cluster war langzeitstabil, reproduzierbar herstellbar und betrug ca. 2,0 – 2,5 nm. Aus der Partikelgröße und dem spektros¬kopischen Nachweis von Metalloxobindungen konnte ein Strukturvorschlag basierend auf den zugrundeliegenden Titan- und Zirkoniumkomplexen erstellt werden. Dabei bilden MO6 Komplexe das Grundgerüst stäbchenförmiger, heterometallischer Cluster. Die polymerisierbaren Methacrylatliganden befinden sich auf der Oberfläche und sind gut zugänglich für die Polymerisationsreaktion. Die mittlere Anzahl an Methacrylatliganden pro PZT-Cluster wurde zu 5 - 25 je nach Gewichtung abgeschätzt. Bei der UV-lithographischen Strukturierung ergaben sich zwei unerwartete Effekte. Zum einen trat nach der Schichtherstellung eine reversible Trübung des PZT-Sols auf, welches auf konzentrations¬bedingte Phasenseparation zurückgeführt werden konnte. Zum anderen setzte sich unter N2 Atmosphäre die lichtinduzierte radikalische Kettenreaktion in den methacrylat-funktionalisierten PZT-Solschichten auch in die unbelichteten Bereiche fort. Dieser Effekt wird sonst in dieser Deutlichkeit nur von kationischen Polymerisationsreaktionen beobachtet und auf lange Radikal¬lebensdauern zurückgeführt und wurde mittels Photo-Differentialkalorimetrie weitergehend untersucht. Allerdings konnte aufgrund der Probengeometrie der Einfluss der Atmosphäre mit der Photo-DSC-Methode nicht eindeutig geklärt werden. Die Qualität der pyrolysierten PZT-Schichten konnte durch Variation der Feststoffgehalte und der Pyrolysebedingungen optimiert werden. So wurden durch die Verdünnung der PZT-Sole auf 25 Gew. % Feststoffgehalt bei ansonsten analogen Pyrolyse¬bedingungen dichtere und homogenere Schichten erhalten, wohingegen PZT-Solschichten mit einem Feststoffgehalt von 31 Gew.-% eine xerogelartige Struktur durch agglomerierte Partikel zeigten. Die untersuchten Substrate wiesen einen deutlichen Einfluss auf die nach der Pyrolyse erhaltenen PZT-Schichten auf. Unmetallisierte Silizium-Wafer eigneten sich zwar zur Untersuchung der UV-lithographischen Herstellung strukturierter Solschichten, bei der Pyrolyse bildeten sich jedoch unerwünschte Bleisilicat¬schmelzen, die der PZT-Bildung entgegen wirkten. Weiterhin wurden platinierten Silizium-Wafer mit Titanhaftvermittler¬schicht und SiO2-Sperrschicht verwendet. Diese Substrate zeigten eine durch die hohen Pyrolyse¬temperaturen induzierten Diffusion der Haftvermittlerschicht in die Platinmetallisierung und in der Folge eine Delamination aufgrund hoher Druckspannung in der PZT-Schicht, welche durch die Entfernung der organischen Bestandteile aus der Solschicht resultierte. In der Folge entstanden mechanisch instabile Proben. Die Delamination konnte durch Zwischensinterschritte bei 360 °C bzw. durch die Pyrolyse auf Heizplatten reduziert, jedoch nicht vollständig vermieden werden. Aus diesem Grund konnten keine ferroelektrischen Eigenschaften der PZT-Schichten auf diesen Substraten ermittelt werden. Lediglich auf Stahlsubstraten konnten elektrisch dichte Schichten hergestellt werden. Die Polymerisationsreaktion eines ausgesuchten PZT-Sols, welches bei den Strukturierungs- und Pyrolyseuntersuchungen die besten Ergebnisse zeigte, wurde näher untersucht, um ein Verständnis zu den ablaufenden Reaktionen zu erhalten. Die Reaktion zeigt den für radikalische Kettenpolymerisationen typischen Trommsdorf- bzw. Gel-Effekt. Durch die Verdünnung der PZT-Cluster konnten trotz hoher Anzahl an C=C-Bindungen pro Monomer, d. h. stark quervernetzender Spezies, sehr hohe Umsetzungsgrade erreicht werden. Die initiator¬gehalts-abhängige Steigerung der Reaktionsenthalpie während der Belichtung konnte mit steigenden Umsetzungs¬graden korreliert werden. Dieses Verhalten wird in der Literatur für eine Vielzahl an methacrylatbasierten Monomeren beschrieben. Der empirische Zusammenhang zwischen der Reaktionsrate und der Initiatorkonzentration konnte für das methacrylat¬funktionalisierte PZT-Sol zu bestimmt werden. Die Gesamtaktivierungenergie konnte ebenfalls in Abhängigkeit vom Reaktionsumsatz ermittelt werden. Die Polymerisation eines konzentrierten PZT-Sols mit difunktionellen Monomeren zeigte höhere Umsetzungsgrade als die entsprechenden Reinsubstanzen und ein späteres Eintreten des Gelpunkts. Dies wird zurückgeführt auf die niedrigere Viskosität sowie die geringere Molekülgröße des Reaktivverdünners und die in der Folge bessere Infiltration des durch das PZT-Sol aufgespannten Netzwerks mit zusätzlichen kleinen und beweglichen Monomeren. Da bei der thermischen Behandlung der polymerisierten PZT-Schichten die experimentellen Bedingungen, wie z. B. Heizrate oder Anfangstemperatur der Pyrolyse, einen signifikanten Einfluss besitzen, wurden energiedispersive in-situ-Röntgenbeugungsexperimente mit Hilfe von Synchrotron¬strahlung durch¬geführt. Hierbei konnte vor allem der Einfluss der organischen Polymerisation und der Anfangstemperatur der Pyrolyse auf die Phasenentwicklung des Precursor-Sols untersucht werden. Dabei zeigte sich besonders deutlich, dass die PZT-Bildungstemperatur durch die Belichtung der Probe und damit der Bildung des organischen Netzwerks steigt. Dies wird auf das starke organische Netzwerk und den erhöhten Energiebedarf zur Reorganisation zurückgeführt. Durch eine erhöhte Anfangstemperatur der Pyrolyse von 500 °C kann die in der Literatur beschriebene Verringerung der unerwünschten Pyrochlor-Phase beobachtet werden. Zudem ist die PZT-Bildungstemperatur hierbei niedriger als bei Pyrolysen ab Raumtemperatur. Dies wird mit einer durch den geringeren Anteil an Pyrochlor-Phase erhöhten Triebkraft zur PZT-Bildung erklärt. Die konsekutive Phasenumwandlung von Pyrochlor in die erwünschte PZT-Phase ist bei Pyrolysen ab Raumtemperatur später abgeschlossen als bei Pyrolysen ab 500 °C. Dies kann mit dem geringeren Anteil an Pyrochlor-Phase erklärt werden, da sich ab 500 °C bereits die PZT-Phase zu bilden beginnt. Der Vergleich der Halbwertsbreiten des intensitätsstarken Reflexes bei 31 ° zeigte, dass die Belichtung der Solschichten zu größeren Kristalliten führt, was auf eine niedrigere Nukleationsrate während der Kristallisation zurückzuführen ist. Bei der Auswertung und Diskussion der Ergebnisse der im Rahmen dieser Arbeit untersuchten Thematik ergaben sich einige Ansatzpunkte für weitere Untersuchungen, die jedoch nicht im zeitlichen und thematischen Rahmen dieser Arbeit betrachtet werden konnten. So wäre es interessant weitere Substrate auf ihre Eignung bei der, für die Herstellung strukturierten PZT-Schichten notwendigen, hohen thermischen Belastung zu testen, da die hier untersuchten platinierten Silizium-Wafer bzw. die Stahlsubstrate deutliche Nachteile zeigten. Des Weiteren können neben den hier behandelten polymerisierbaren Carbonsäureliganden weitere mehrzähnige Liganden und dessen Einfluss auf die Precursormaterialien für die Herstellung strukturierter anorganischer Schichten untersucht werden. β-Diketone, Aminoalkohole und auch Phosphonate bilden ebenfalls stabile Metall-Ligand-Bindungen und könnten so die Integration polymerisierbarer Gruppen in die PZT-Cluster analog zu der im Rahmen dieser Arbeit verwendeten Carbonsäure ermöglichen. Das hier erarbeitete Konzept könnte neben den untersuchten ferroelektrischen Schichtmaterialien ebenfalls auf andere dielektrische oder magnetische Materialklassen, wie z. B. Bariumtitanat oder Magnetit übertragen werden. Die Herstellung photostrukturierbarer anorganischer Schichten durch den Einbau polymerisierbarer Liganden eignet sich für zahlreiche Materialklassen, die über flüssige Sol-Gel-Vorstufen synthetisiert werden können. Darüber hinaus können weitere Pyrolysebedingungen mit den hier vorgestellten Analysemethoden untersucht werden. So könnten z. B. verschiedene Atmosphären oder unterschiedliche Heizraten innerhalb eines Pyrolysezyklus variiert werden, um ihren Einfluss auf die Herstellung rissfreier und phasenreiner Schichten zu untersuchen. Dazu müsste der hier vorgestellte experimentelle Aufbau dahingehend erweitert werden, dass eine Gaszufuhr während der Pyrolyse möglich ist. N2 - The broad objective of this study was to investigate the properties of photopolymerizable precursor sols using organically polymerizable titan(IV) and zirconium(IV) complexes, which are commonly used in the synthesis of inorganic-organic hybrid polymers. With the help of these complexes an approach to the preparation of photochemically patterned, inorganic thin films was developed. Lead zirconate titanate (PZT) was chosen as the inorganic material. The polymerizable moiety was introduced into the precursor sol using methacrylic acid as the polymerizable ligand. Particular attention has been drawn to the investigation of the photochemical reaction of the precursor sol and on the in-situ analysis of the thermally induced conversion into the inorganic PZT thin film, respectively. The process for the preparation of photochemically patterned, inorganic thin films can be divided into two independent steps. These are, on the one hand, the light induced organic polymerization of the synthesized precursor sol and on the other hand, the thermal decomposition of the organic moieties along with the formation of crystalline PZT. Patterned PZT thin films were prepared, for example, using a methacrylated PZT-sol based on n butanol. The solid content of this precursor sol was set to 25 wt. % by diluting with high-boiling point organic solvents. The sol was spin-coated onto steel substrates, followed by the patterning process due to light-induced polymerization. After removal of the unexposed areas using a solvent developer, the pyrolysis reaction was started at 500 °C. The inorganic thin-film was obtained by further heating with a heating rate of 5 K/min to reach a final temperature of 700 °C. Although ferroelectric behavior was verified for these samples, their properties are still inferior compared to commonly prepared ferroelectric thin films. This has been attributed to several different reasons, such as low thickness of the thin film, the formation of undesired side-products and acceptor-doping due to ion diffusion out of the steel substrate, respectively. Firstly, there is an increased risk of electric breakdown within the PZT thin-films due to the low thickness of the films. Secondly, an undesired side-product (Pb2(CrO4)O) forms at the interface of the steel substrate and the PZT thin-film. This leads to a non-ferroelectic layer within the PZT, which drastically reduces the ferroelectric behavior. Finally, Cr3+ ions of the steel substrate can migrate into the PZT thin-film forming an acceptor doped material, which results in a reduced domain wall mobility. The synthesis of the PZT sol was investigated and it was shown that the formation of undesired ester by-products could be avoided, if the volatile products of the ligand exchange reaction of alcohol and methacrylic acid are distilled at reduced pressure, as lower distillation temperatures have to be applied. The coordination of the methacrylic acid ligand in the resulting complexes is bidentate. Although the boiling temperature of n butanol is higher and its vapor pressure is lower, a higher amount of alcohol can be removed during distillation in the case of n butanol based PZT sols compared to sols based on n propanol. This may be attributed to a favored ligand exchange reaction. The size of the PZT precursor cluster is is about 2,0 – 2,5 nm. The methacrylated PZT sol can be prepared with a high degree of reproducibility and is storage-stable over several months. Based on this particle size and the spectroscopic detection of metal oxo groups within the PZT precursor sol, a structure was proposed, which is made up of titan- and zirconium-containing MO6-complexes forming rod-like heterometallic clusters. The polymerizable methacrylic ligands are bound to the outer surface of the clusters and thus are susceptible to the polymerization reaction. The average number of methacrylic ligands per PZT sol cluster was estimated at 5 – 25 depending on the weighting. The UV lithography process was marked by two effects. On the one hand the spin-coated PZT precursor films featured a reversible hazing, which was attributed to a concentration dependent phase separation of the precursor. On the other hand, if the light exposure was performed under a constant stream of nitrogen, the radical polymerization reaction proceeded into the shadow areas of the mask. Usually, this behavior is limited to cationic polymerization and is attributed to long lifetimes of the reactive species. In Photo-DSC experiments, this effect is observed for the methacrylated PZT-sol, as well. However, due to the different sample setup the influence of the atmosphere could not be resolved with this Photo-DSC method. The quality of the pyrolyzed PZT thin films was optimized by variation of the solid content and by variation of the pyrolysis parameters. The methacrylated PZT sols with a solid content of 25 % lead to the formation of homogenous and dense thin-films, whereas the pyrolysis of PZT sols with a solid content of 31 % resulted in xerogel like morphology due to agglomeration of precursor particles. The substrates, used within this work, exerted a major influence on the PZT thin films. Pure silicon wafers were appropriate for the investigations concerning the UV lithography process or the polymerization reaction. However, during the thermal treatment of the PZT precursor thin film, the silicon substrate reacted with the sol forming undesired lead silicate meltings, which inhibited PZT formation. The platinized silicon wafers containing titan and silicon oxide sublayers also showed increased reaction during thermal annealing as the titan adhesion layer migrated into the platinum electrode. As a result, the compressive stress generated in the PZT thin-film due to the combustion of the organic residues could not be compensated by the remaining adhesion layer and, consequently, the platinum electrode delaminated. The resulting samples exhibited a very low mechanical stability. The delamination of the electrode layers was reduced by either intermediate annealing steps at 360 °C or by the application of hotplates instead of a furnace. However, a complete prevention of delamination was not achieved. Hence, due to the ensuing electric breakdown, no ferroelectric properties could be obtained from photochemically patterned PZT thin films on these platinized silicon substrates. Furthermore, the polymerization of the methacrylated PZT sol was investigated in order to obtain a better understanding of the reactions that take place. The light induced polymerization exhibited the Trommsdorf or gel effect, which is typical for radical chain reactions. After curing the resulting films showed very high conversion rates, when diluted in various solvents. This is obtained regardless of the high number of polymerizable C=C bonds per cluster, which can lead to highly branched networks in which the mobility of reactive moieties is usually reduced significantly even at low conversion rates. The increase in the reaction enthalpy depending on the content of UV initiator sufficiently correlates with increasing conversion rates. In literature, this behavior is reported for a number of methacrylate¬-based monomers. The empirical relation of the reaction rates and the concentration of UV initiator was determined as . The overall activation energy for the polymerization of the methacrylated PZT sol was calculated depending on the reaction conversion. Additionally, the copolymerization with difunctional monomers exhibited higher conversion rates than the pure monomers and the onset of the gel effect is delayed. Energy dispersive in-situ x-ray diffraction analyses using synchrotron radiation were performed to examine the influence of the different pyrolysis parameters, such as heating rate and starting temperature of the annealing step. It was observed, that the polymerization of the PZT precursor thin-films, and thus the formation of an organic network, resulted in an increase in the temperature needed for PZT formation. This effect was attributed to the strong covalent organic network, which had accumulated during polymerization, and thus an increased energy was needed for reorganization. By increasing the starting temperature of the annealing step to 500 °C, the reduced formation of undesired pyrochlore was observed, as previously reported in literature. Furthermore, the PZT formation temperature is lower compared to pyrolysis starting at room temperature. This was explained by an increased driving force for PZT crystallization due to a lower amount of pyrochlore phase. In addition, the consecutive phase transformation from pyrochlore into PZT was completed at lower temperatures, if the starting temperature was 500 °C. A comparison of the halfwidth of the PZT reflex at 31° revealed that the polymerized PZT thin films exhibited larger crystallite sizes compared to unexposed thin films. In addition to the higher formation temperature, this was accredited to a lower nucleation rate in the polymerized PZT precursor films. During the interpretation and discussion of the results of this thesis, a number of new and interesting aspects arose, which could not be dealt with within the framework of this study. Therefore, it would be interesting to investigate further substrates for their suitability within the PZT preparation process. The substrates used within this work exhibited a number of significant disadvantages, such as thermal instability and undesired reactions with the PZT precursor. Additionally, alongside the methacrylic ligand which was tested within this work, other polymerizable ligands may be used for the synthesis of photopatternable precursor sols. β diketones, amino alcohols and phosphonates also form stable metal ligand bonds, and thus could be used to introduce the polymerizable moiety. The resulting concept of polymerizable precursors for inorganic thin films might also be transferred to dielectric or magnetic material classes, such as barium titanate. In principle, this process is applicable for all materials that can be synthesized by liquid sol-gel precursors. Additionally, further parameters of the pyrolysis could be investigated with the in-situ x-ray diffraction method, which was used within this thesis. The influence of different annealing atmospheres or different heating rates could also be examined. For the variation of the reaction atmosphere, an adaption of the experimental setup would have to be realized first, which allows the gas supply. KW - Ultraviolett-Bestrahlung KW - Sol-Gel-Verfahren KW - Dünne Schicht KW - Photostrukturierung KW - Ferroelektrikum KW - PZT KW - Strukturierung Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-108422 ER -