TY - JOUR A1 - Renner, Tobias A1 - Otto, Paul A1 - Kübler, Alexander C. A1 - Hölscher-Doht, Stefanie A1 - Gbureck, Uwe T1 - Novel adhesive mineral-organic bone cements based on phosphoserine and magnesium phosphates or oxides JF - Journal of Materials Science: Materials in Medicine N2 - Present surgical situations require a bone adhesive which has not yet been developed for use in clinical applications. Recently, phosphoserine modified cements (PMC) based on mixtures of o-phosphoserine (OPLS) and calcium phosphates, such as tetracalcium phosphate (TTCP) or α-tricalcium phosphate (α-TCP) as well as chelate setting magnesium phosphate cements have gained increasing popularity for their use as mineral bone adhesives. Here, we investigated new mineral-organic bone cements based on phosphoserine and magnesium phosphates or oxides, which possess excellent adhesive properties. These were analyzed by X-ray diffraction, Fourier infrared spectroscopy and electron microscopy and subjected to mechanical tests to determine the bond strength to bone after ageing at physiological conditions. The novel biomineral adhesives demonstrate excellent bond strength to bone with approximately 6.6–7.3 MPa under shear load. The adhesives are also promising due to their cohesive failure pattern and ductile character. In this context, the new adhesive cements are superior to currently prevailing bone adhesives. Future efforts on bone adhesives made from phosphoserine and Mg2+ appear to be very worthwhile. Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-357342 VL - 34 ER - TY - JOUR A1 - Ouhaddi, Yassine A1 - Charbonnier, Baptiste A1 - Porge, Juliette A1 - Zhang, Yu-Ling A1 - Garcia, Isadora A1 - Gbureck, Uwe A1 - Grover, Liam A1 - Gilardino, Mirko A1 - Harvey, Edward A1 - Makhoul, Nicholas A1 - Barralet, Jake T1 - Development of neovasculature in axially vascularized calcium phosphate cement scaffolds JF - Journal of Functional Biomaterials N2 - Augmenting the vascular supply to generate new tissues, a crucial aspect in regenerative medicine, has been challenging. Recently, our group showed that calcium phosphate can induce the formation of a functional neo-angiosome without the need for microsurgical arterial anastomosis. This was a preclinical proof of concept for biomaterial-induced luminal sprouting of large-diameter vessels. In this study, we investigated if sprouting was a general response to surgical injury or placement of an inorganic construct around the vessel. Cylindrical biocement scaffolds of differing chemistries were placed around the femoral vein. A contrast agent was used to visualize vessel ingrowth into the scaffolds. Cell populations in the scaffold were mapped using immunohistochemistry. Calcium phosphate scaffolds induced 2.7–3 times greater volume of blood vessels than calcium sulphate or magnesium phosphate scaffolds. Macrophage and vSMC populations were identified that changed spatially and temporally within the scaffold during implantation. NLRP3 inflammasome activation peaked at weeks 2 and 4 and then declined; however, IL-1β expression was sustained over the course of the experiment. IL-8, a promoter of angiogenesis, was also detected, and together, these responses suggest a role of sterile inflammation. Unexpectedly, the effect was distinct from an injury response as a result of surgical placement and also was not simply a foreign body reaction as a result of placing a rigid bioceramic next to a vein, since, while the materials tested had similar microstructures, only the calcium phosphates tested elicited an angiogenic response. This finding then reveals a potential path towards a new strategy for creating better pro-regenerative biomaterials. KW - angiogenesis KW - axial vascularization KW - bioceramic KW - bioinorganic KW - calcium phosphate KW - NLRP3 KW - inflammation Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-304026 SN - 2079-4983 VL - 14 IS - 2 ER - TY - THES A1 - Witteler, Charlotte Marie T1 - Untersuchung des zellbiologischen Verhaltens von Fibroblasten in modifizierten Gelatine-Methacrylat basierten Harzen für den volumetrischen Biodruck T1 - Investigation of the cell biological behavior of fibroblasts in modified gelatin-methacrylate based resins for volumetric bioprinting N2 - Was vor einigen Jahren undenkbar erschien, könnte zukünftig möglich sein: Krankes Gewebe mit Gesundem ersetzen, das in vitro mit modernsten Biofabrikationstechniken hergestellt wird. Dabei werden bisherige Grenzen überschritten: Während lichtbasierte Biodruckverfahren wie die Zwei-Photonen-Polymerisation Auflösungen bis in den Nanometerbereich erzielen, ermöglicht der Volumetrische Biodruck (VB) den Druck zentimetergroßer Konstrukte in wenigen Sekunden. Diese Geschwindigkeiten erweisen sich unter Biodruckverfahren als konkurrenzlos und werden erreicht, da das Bioharz nicht konsekutiv, sondern zugleich vernetzt wird. Einschränkend gilt bislang nur der Mangel an geeigneten Bioharzen für den VB. Daher beschäftigt sich vorliegende Arbeit mit der Charakterisierung und Modifikation eines dafür geeigneten Bioharzes: Gelatine-Methacrylat (GelMA). Dank seiner Zusammensetzung ähnelt das etablierte Hydrogelsystem der Extratrazellularmatrix: Der Gelatine-Anteil ermöglicht Biokompatibilität und Bioaktivität durch zelladhäsive sowie degradierbare Aminosäure-Sequenzen. Zugleich können durch photovernetzbare Methacryloyl-Substituenten Konstrukte mit einer Formstabilität bei 37 °C erzeugt werden. Zunächst wurde das Bioharz zellbiologisch charakterisiert, indem mit der embryonalen Mausfibroblasten-Zelllinie NIH-3T3 beladene GelMA-Zylinder gegossen, photopolymerisiert und kultiviert wurden. Im Verlauf einer Woche wurde die Zytokompatibilität der Gele anhand der Proliferationsfähigkeit (PicoGreen-Assay), des Metabolismus (CCK-8-Assay) und der Vitalität (Live/Dead-Assay) der Zellen beurteilt. Dabei wurden Polymerkonzentrationen von 6 – 8 % sowie GelMA-Harze zweier verschiedener Molekulargewichte verglichen. Alle hergestellten Gele erwiesen sich als zytokompatibel, 6 % ige Gele ließen im Inneren jedoch zusätzlich eine beginnende Zellspreizung zu und ein niedriges GelMA-Molekulargewicht verstärkte die gemessene Proliferation. Die sich anschließende mechanische und physikalische Charakterisierung belegte, dass höher konzentrierte Gele einen größeren E-Modul aufwiesen und damit steifer waren. Eine Modifikation der Gele mit Fibronektin beeinflusste die Zellverträglichkeit weder positiv noch negativ und die Zugabe von Kollagen war wegen Entmischungseffekten nicht bewertbar. Es liegt die Vermutung nah, dass eine weitere Reduktion der Polymerkonzentration und damit Verringerung der Gelsteifigkeit der Schlüssel für mehr Zellspreizung und -wachstum ist. Da jedoch die Druckbarkeit des Bioharzes die weitere Senkung des GelMA-Gehalts limitiert, sollten zunächst Methoden entwickelt werden, welche die Netzwerkdichte des GelMAs anderweitig herabsetzen. N2 - What seemed unthinkable a few years ago could be possible in the future: replacing diseased tissue with healthy tissue produced in vitro using the latest biofabrication techniques. Previous limits are being exceeded: While light-based bioprinting processes such as two-photon polymerization achieve resolutions down to the nanometer range, volumetric bioprinting (VB) makes it possible to print centimeter-sized constructs in just a few seconds. These speeds are unrivaled among bioprinting processes and are achieved because the bioresin is not cross-linked consecutively but simultaneously. The only limitation to date is the lack of suitable bioresins for VB. Therefore, the present work deals with the characterization and modification of a suitable bioresin: gelatine methacrylate (GelMA). Thanks to its composition, the established hydrogel system is similar to the extracellular matrix: The gelatine component enables biocompatibility and bioactivity through cell-adhesive as well as degradable amino acid sequences. At the same time, photo-crosslinkable methacryloyl substituents can be used to produce constructs with dimensional stability at 37 °C. First, the bioresin was characterized cell biologically by casting, photopolymerizing and culturing GelMA cylinders loaded with the embryonic mouse fibroblast cell line NIH-3T3. Over the course of a week, the cytocompatibility of the gels was assessed based on proliferation capacity (PicoGreen assay), metabolism (CCK-8 assay) and viability (Live/Dead assay) of the cells. Polymer concentrations of 6 - 8 % and GelMA resins of two different molecular weights were compared. All gels produced were found to be cytocompatible, however, 6 % gels additionally allowed incipient cell spreading inside and a low GelMA molecular weight increased the measured proliferation. The subsequent mechanical and physical characterization showed that gels with higher concentration had a higher modulus of elasticity and were therefore stiffer. Modifications of the gels with fibronectin had neither a positive nor negative effect on cell compatibility and the addition of collagen could not be evaluated due to segregation effects. It is reasonable to assume that further reduction in polymer concentration and thus a reduction in gel stiffness is the key to more cell spreading and growth. However, since the printability of the bioresin limits further reduction of the GelMA content, methods should first be developed to reduce the network density of the GelMA in other ways. KW - 3D Bioprinting KW - Fibroblast KW - Gelatine KW - Polymer-Gel KW - GelMA KW - Bioharz KW - Volumetrischer Biodruck KW - Polymergehalt KW - Modifikation Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-349460 ER - TY - THES A1 - Andelovic, Kristina T1 - Characterization of arterial hemodynamics using mouse models of atherosclerosis and tissue-engineered artery models T1 - Charakterisierung arterieller Hämodynamiken in atherosklerotischen Mausmodellen und tissue-engineerten Arterienmodellen N2 - Within this thesis, three main approaches for the assessment and investigation of altered hemodynamics like wall shear stress, oscillatory shear index and the arterial pulse wave velocity in atherosclerosis development and progression were conducted: 1. The establishment of a fast method for the simultaneous assessment of 3D WSS and PWV in the complete murine aortic arch via high-resolution 4D-flow MRI 2. The utilization of serial in vivo measurements in atherosclerotic mouse models using high-resolution 4D-flow MRI, which were divided into studies describing altered hemodynamics in late and early atherosclerosis 3. The development of tissue-engineered artery models for the controllable application and variation of hemodynamic and biologic parameters, divided in native artery models and biofabricated artery models, aiming for the investigation of the relationship between atherogenesis and hemodynamics Chapter 2 describes the establishment of a method for the simultaneous measurement of 3D WSS and PWV in the murine aortic arch at, using ultra high-field MRI at 17.6T [16], based on the previously published method for fast, self-navigated wall shear stress measurements in the murine aortic arch using radial 4D-phase contrast MRI at 17.6 T [4]. This work is based on the collective work of Dr. Patrick Winter, who developed the method and the author of this thesis, Kristina Andelovic, who performed the experiments and statistical analyses. As the method described in this chapter is basis for the following in vivo studies and undividable into the sub-parts of the contributors without losing important information, this chapter was not split into the single parts to provide fundamental information about the measurement and analysis methods and therefore better understandability for the following studies. The main challenge in this chapter was to overcome the issue of the need for a high spatial resolution to determine the velocity gradients at the vascular wall for the WSS quantification and a high temporal resolution for the assessment of the PWV without prolonging the acquisition time due to the need for two separate measurements. Moreover, for a full coverage of the hemodynamics in the murine aortic arch, a 3D measurement is needed, which was achieved by utilization of retrospective navigation and radial trajectories, enabling a highly flexible reconstruction framework to either reconstruct images at lower spatial resolution and higher frame rates for the acquisition of the PWV or higher spatial resolution and lower frame rates for the acquisition of the 3D WSS in a reasonable measurement time of only 35 minutes. This enabled the in vivo assessment of all relevant hemodynamic parameters related to atherosclerosis development and progression in one experimental session. This method was validated in healthy wild type and atherosclerotic Apoe-/- mice, indicating no differences in robustness between pathological and healthy mice. The heterogeneous distribution of plaque development and arterial stiffening in atherosclerosis [10, 12], however, points out the importance of local PWV measurements. Therefore, future studies should focus on the 3D acquisition of the local PWV in the murine aortic arch based on the presented method, in order to enable spatially resolved correlations of local arterial stiffness with other hemodynamic parameters and plaque composition. In Chapter 3, the previously established methods were used for the investigation of changing aortic hemodynamics during ageing and atherosclerosis in healthy wild type and atherosclerotic Apoe-/- mice using the previously established methods [4, 16] based on high-resolution 4D-flow MRI. In this work, serial measurements of healthy and atherosclerotic mice were conducted to track all changes in hemodynamics in the complete aortic arch over time. Moreover, spatially resolved 2D projection maps of WSS and OSI of the complete aortic arch were generated. This important feature allowed for the pixel-wise statistical analysis of inter- and intragroup hemodynamic changes over time and most importantly – at a glance. The study revealed converse differences of local hemodynamic profiles in healthy WT and atherosclerotic Apoe−/− mice, with decreasing longWSS and increasing OSI, while showing constant PWV in healthy mice and increasing longWSS and decreasing OSI, while showing increased PWV in diseased mice. Moreover, spatially resolved correlations between WSS, PWV, plaque and vessel wall characteristics were enabled, giving detailed insights into coherences between hemodynamics and plaque composition. Here, the circWSS was identified as a potential marker of plaque size and composition in advanced atherosclerosis. Moreover, correlations with PWV values identified the maximum radStrain could serve as a potential marker for vascular elasticity. This study demonstrated the feasibility and utility of high-resolution 4D flow MRI to spatially resolve, visualize and analyze statistical differences in all relevant hemodynamic parameters over time and between healthy and diseased mice, which could significantly improve our understanding of plaque progression towards vulnerability. In future studies the relation of vascular elasticity and radial strain should be further investigated and validated with local PWV measurements and CFD. Moreover, the 2D histological datasets were not reflecting the 3D properties and regional characteristics of the atherosclerotic plaques. Therefore, future studies will include 3D plaque volume and composition analysis like morphological measurements with MRI or light-sheet microscopy to further improve the analysis of the relationship between hemodynamics and atherosclerosis. Chapter 4 aimed at the description and investigation of hemodynamics in early stages of atherosclerosis. Moreover, this study included measurements of hemodynamics at baseline levels in healthy WT and atherosclerotic mouse models. Due to the lack of hemodynamic-related studies in Ldlr-/- mice, which are the most used mouse models in atherosclerosis research together with the Apoe-/- mouse model, this model was included in this study to describe changing hemodynamics in the aortic arch at baseline levels and during early atherosclerosis development and progression for the first time. In this study, distinct differences in aortic geometries of these mouse models at baseline levels were described for the first time, which result in significantly different flow- and WSS profiles in the Ldlr-/- mouse model. Further basal characterization of different parameters revealed only characteristic differences in lipid profiles, proving that the geometry is highly influencing the local WSS in these models. Most interestingly, calculation of the atherogenic index of plasma revealed a significantly higher risk in Ldlr-/- mice with ongoing atherosclerosis development, but significantly greater plaque areas in the aortic arch of Apoe-/- mice. Due to the given basal WSS and OSI profile in these two mouse models – two parameters highly influencing plaque development and progression – there is evidence that the regional plaque development differs between these mouse models during very early atherogenesis. Therefore, future studies should focus on the spatiotemporal evaluation of plaque development and composition in the three defined aortic regions using morphological measurements with MRI or 3D histological analyses like LSFM. Moreover, this study offers an excellent basis for future studies incorporating CFD simulations, analyzing the different measured parameter combinations (e.g., aortic geometry of the Ldlr-/- mouse with the lipid profile of the Apoe-/- mouse), simulating the resulting plaque development and composition. This could help to understand the complex interplay between altered hemodynamics, serum lipids and atherosclerosis and significantly improve our basic understanding of key factors initiating atherosclerosis development. Chapter 5 describes the establishment of a tissue-engineered artery model, which is based on native, decellularized porcine carotid artery scaffolds, cultured in a MRI-suitable bioreactor-system [23] for the investigation of hemodynamic-related atherosclerosis development in a controllable manner, using the previously established methods for WSS and PWV assessment [4, 16]. This in vitro artery model aimed for the reduction of animal experiments, while simultaneously offering a simplified, but completely controllable physical and biological environment. For this, a very fast and gentle decellularization protocol was established in a first step, which resulted in porcine carotid artery scaffolds showing complete acellularity while maintaining the extracellular matrix composition, overall ultrastructure and mechanical strength of native arteries. Moreover, a good cellular adhesion and proliferation was achieved, which was evaluated with isolated human blood outgrowth endothelial cells. Most importantly, an MRI-suitable artery chamber was designed for the simultaneous cultivation and assessment of high-resolution 4D hemodynamics in the described artery models. Using high-resolution 4D-flow MRI, the bioreactor system was proven to be suitable to quantify the volume flow, the two components of the WSS and the radStrain as well as the PWV in artery models, with obtained values being comparable to values found in literature for in vivo measurements. Moreover, the identification of first atherosclerotic processes like intimal thickening is achievable by three-dimensional assessment of the vessel wall morphology in the in vitro models. However, one limitation is the lack of a medial smooth muscle cell layer due to the dense ECM. Here, the utilization of the laser-cutting technology for the generation of holes and / or pits on a microscale, eventually enabling seeding of the media with SMCs showed promising results in a first try and should be further investigated in future studies. Therefore, the proposed artery model possesses all relevant components for the extension to an atherosclerosis model which may pave the way towards a significant improvement of our understanding of the key mechanisms in atherogenesis. Chapter 6 describes the development of an easy-to-prepare, low cost and fully customizable artery model based on biomaterials. Here, thermoresponsive sacrificial scaffolds, processed with the technique of MEW were used for the creation of variable, biomimetic shapes to mimic the geometric properties of the aortic arch, consisting of both, bifurcations and curvatures. After embedding the sacrificial scaffold into a gelatin-hydrogel containing SMCs, it was crosslinked with bacterial transglutaminase before dissolution and flushing of the sacrificial scaffold. The hereby generated channel was subsequently seeded with ECs, resulting in an easy-to-prepare, fast and low-cost artery model. In contrast to the native artery model, this model is therefore more variable in size and shape and offers the possibility to include smooth muscle cells from the beginning. Moreover, a custom-built and highly adaptable perfusion chamber was designed specifically for the scaffold structure, which enabled a one-step creation and simultaneously offering the possibility for dynamic cultivation of the artery models, making it an excellent basis for the development of in vitro disease test systems for e.g., flow-related atherosclerosis research. Due to time constraints, the extension to an atherosclerosis model could not be achieved within the scope of this thesis. Therefore, future studies will focus on the development and validation of an in vitro atherosclerosis model based on the proposed bi- and three-layered artery models. In conclusion, this thesis paved the way for a fast acquisition and detailed analyses of changing hemodynamics during atherosclerosis development and progression, including spatially resolved analyses of all relevant hemodynamic parameters over time and in between different groups. Moreover, to reduce animal experiments, while gaining control over various parameters influencing atherosclerosis development, promising artery models were established, which have the potential to serve as a new platform for basic atherosclerosis research. N2 - Im Rahmen dieser Arbeit wurden drei Hauptansätze zur Bewertung und Untersuchung der veränderten Hämodynamik wie Wandschubspannung, des oszillatorischen Scherindex und der arteriellen Pulswellengeschwindigkeit bei der Entwicklung und Progression der Atherosklerose durchgeführt: 1. Die Etablierung einer schnellen Methode zur gleichzeitigen Bestimmung der 3D-Wandschubspannung und der Pulswellengeschwindigkeit im gesamten Aortenbogen der Maus mittels hochauflösender 4D-Fluss-MRT 2. Die Verwendung von seriellen in vivo Messungen in atherosklerotischen Mausmodellen mittels hochauflösender 4D-Fluss-MRT, die in Studien zur Beschreibung der veränderten Hämodynamik bei später und früher Atherosklerose aufgeteilt wurden 3. Die Entwicklung von tissue-engineerten Arterienmodellen für die kontrollierte Anwendung und Variation von hämodynamischen und biologischen Parametern, unterteilt in native Arterienmodelle und biofabrizierte Arterienmodelle, mit dem Ziel, die Beziehung zwischen Atherogenese und veränderter Hämodynamik zu untersuchen Kapitel 2 beschreibt die Etablierung einer Methode zur gleichzeitigen Messung von 3D-Wandschubspannung und Pulswellengeschwindigkeit im Aortenbogen der Maus unter Verwendung der Ultrahochfeld-MRT bei 17,6T [16], die auf der zuvor veröffentlichten Methode zur schnellen, selbstnavigierten Messung der Wandschubspannung im Aortenbogen der Maus unter Verwendung der radialen 4D-Phasenkontrast-MRT bei 17,6T [4] basiert. Dieses Projekt basiert auf der gemeinsamen Arbeit von Dr. Patrick Winter, der diese Methode entwickelt hat, und der Autorin dieser Thesis, Kristina Andelovic, die die Experimente und statistischen Analysen durchgeführt hat. Da die in diesem Kapitel beschriebene Methode die Grundlage für die folgenden in vivo Studien darstellt und sich nicht in die einzelnen Beiträge der Autoren aufteilen lässt, ohne dass wichtige Informationen verloren gehen, wurde dieses Kapitel nicht in die einzelnen Teile aufgeteilt, um grundlegende Informationen über die Mess- und Analysemethoden zu liefern und somit eine bessere Verständlichkeit für die folgenden Studien zu gewährleisten. Die größte Herausforderung in diesem Kapitel bestand darin, die Anforderung an eine hohe räumliche Auflösung zur Bestimmung der Geschwindigkeitsgradienten an der Gefäßwand für die WSS-Quantifizierung und an eine hohe zeitliche Auflösung für die Bestimmung der Pulswellengeschwindigkeit zu erfüllen, ohne die Messzeit aufgrund der Notwendigkeit von zwei separaten Messungen zu verlängern. Darüber hinaus ist für eine vollständige Erfassung der Hämodynamik im murinen Aortenbogen eine vollständige 3D-Messung des Aortenbogens erforderlich, die durch die Nutzung der retrospektiven Navigation und radialen Trajektorien erreicht wurde. Dies wurde durch ein hoch flexibles Rekonstruktionssystem ermöglicht, das entweder Bilder mit geringerer räumlicher Auflösung und höheren Bildraten für die Erfassung der Pulswellengeschwindigkeit oder mit höherer räumlicher Auflösung und niedrigeren Bildraten für die Erfassung der 3D-WSS in einer angemessenen Messzeit von nur 35 Minuten rekonstruieren konnte. Die in vivo-Bestimmung aller relevanter hämodynamischen Parameter, die mit der Entwicklung und dem Fortschreiten der Atherosklerose zusammenhängen, wurde somit in einer einzigen experimentellen Sitzung ermöglicht. Die Methode wurde an gesunden Wildtyp- und atherosklerotischen Apoe-/- Mäusen validiert, wobei keine Unterschiede in der Robustheit der Messungen zwischen pathologischen und gesunden Mäusen festgestellt werden konnten. Die heterogene Verteilung der Plaqueentwicklung und Arterienversteifung in der Atherosklerose [10, 12] weist jedoch auf die Wichtigkeit lokaler PWV-Messungen hin. Zukünftige Studien sollten sich daher auf die 3D-Erfassung der lokalen PWV im murinen Aortenbogen auf Grundlage der vorgestellten Methode konzentrieren, um räumlich aufgelöste Korrelationen der lokalen arteriellen Steifigkeit mit anderen hämodynamischen Parametern und der Plaquezusammensetzung zu ermöglichen. In Kapitel 3 wurden die zuvor etablierten Methoden zur Untersuchung der sich verändernden Hämodynamik in der Aorta während des Alterns und der Atherosklerose bei gesunden Wildtyp- und atherosklerotischen Apoe-/- Mäusen verwendet [4, 16], die auf hochauflösender 4D-Fluss MRT basieren. In dieser Arbeit wurden serielle Messungen an gesunden und atherosklerotischen Mäusen durchgeführt, um alle Veränderungen der Hämodynamik im gesamten Aortenbogen über die Zeit zu verfolgen. Zudem wurden in dieser Arbeit räumlich aufgelöste 2D-Projektionskarten der WSS und des OSI des gesamten Aortenbogens generiert. Diese Methode ermöglichte die pixelweise statistische Analyse der Unterschiede und hämodynamischen Veränderungen zwischen und innerhalb von Gruppen im Zeitverlauf und die Visualisierung auf einen Blick. Die Studie ergab sich gegensätzlich entwickelnde lokale hämodynamische Profile bei gesunden WT- und atherosklerotischen Apoe-/- Mäusen, wobei die longWSS über die Zeit abnahm und der OSI zunahm, während die PWV bei gesunden Mäusen konstant blieb. Im Gegensatz nahm die longWSS zu und der OSI bei kranken Mäusen ab, während die PWV über die Zeit zunahm. Darüber hinaus wurden räumlich aufgelöste Korrelationen zwischen WSS, PWV, Plaque und Gefäßwandeigenschaften ermöglicht, die detaillierte Einblicke in die Zusammenhänge zwischen Hämodynamik und Plaquezusammensetzung in der Atherosklerose bieten. Dabei wurde die zirkumferentielle WSS als potenzieller Marker für die Plaquegröße und -zusammensetzung bei fortgeschrittener Atherosklerose identifiziert. Darüber hinaus ergaben Korrelationen mit der PWV, dass der maximale radiale Druck als potenzieller Marker für die vaskuläre Elastizität dienen könnte. Zusammengefasst demonstriert diese Studie die Nützlichkeit der hochauflösenden 4D-Fluss MRT zur räumlichen Auflösung, Visualisierung und Analyse statistischer Unterschiede in allen relevanten hämodynamischen Parametern im Zeitverlauf und zwischen gesunden und erkrankten Mäusen, was unser Verständnis der Plaqueprogression in Richtung Vulnerabilität erheblich verbessern könnte. In zukünftigen Studien sollte jedoch der Zusammenhang zwischen Gefäßelastizität und radialem Druck weiter untersucht und mit lokalen PWV-Messungen und CFD validiert werden. Darüber hinaus spiegelten die histologischen 2D-Datensätze nicht die 3D-Eigenschaften und regionalen Charakteristika der atherosklerotischen Plaques wider. Daher sollten künftige Studien eine Analyse des 3D-Plaquevolumens und der 3D-Plaquenzusammensetzung sowie morphologische Messungen mittels MRT oder der Lichtblattmikroskopie mit einbeziehen, um das fundamentale Verständnis der Beziehung zwischen veränderter Hämodynamik und der Atherosklerose weiter zu verbessern. In Kapitel 4 ging es um die Beschreibung und Untersuchung der Hämodynamik in frühen Stadien der Atherosklerose. Darüber hinaus umfasste diese Studie zum ersten Mal Messungen der basalen Hämodynamik in gesunden WT- und atherosklerotischen Mausmodellen. Aufgrund des Mangels an Studien, die die Hämodynamik in Ldlr-/- Mäusen beschreiben, die zusammen mit dem Apoe-/- Mausmodell die am häufigsten verwendeten Mausmodelle in der Atheroskleroseforschung sind, wurde dieses Modell in diese Studie integriert, um erstmals die sich verändernde Hämodynamik im Aortenbogen zu Beginn und während der Entwicklung und Progression der frühen Atherosklerose zu beschreiben. In dieser Studie wurden erstmals deutliche Unterschiede in den basalen Aortengeometrien dieser Mausmodelle identifiziert, die zu signifikant unterschiedlichen Fluss- und WSS-Profilen im Ldlr-/- Mausmodell führen. Eine weitere basale Charakterisierung verschiedener Parameter ergab nur modell-charakteristische Unterschiede in den Lipidprofilen, was beweist, dass die Geometrie die lokale WSS in diesen Modellen stark beeinflusst. Interessanterweise ergab die Berechnung des atherogenen Plasma-Indexes ein signifikant höheres Risiko bei Ldlr-/- Mäusen mit fortschreitender Atheroskleroseentwicklung, aber signifikant größere Plaqueflächen im Aortenbogen der Apoe-/- Mäuse. Aufgrund des gegebenen basalen WSS- und OSI-Profils in diesen beiden Mausmodellen - zwei Parameter, die die Plaque-Entwicklung und -Progression stark beeinflussen - gibt es Hinweise darauf, dass sich die regionale Plaque-Entwicklung zwischen diesen Mausmodellen während der Atherogenese stark unterscheidet. Daher sollten sich künftige Studien auf die räumlich-zeitliche Bewertung der Plaqueentwicklung und -Zusammensetzung in den drei definierten Aortenregionen konzentrieren, wobei morphologische Messungen mittels MRT oder histologische 3D-Analysen wie LSFM zum Einsatz kommen. Darüber hinaus bietet diese Studie eine hervorragende Grundlage für künftige Studien mit CFD-Simulationen, in denen die verschiedenen gemessenen Parameterkombinationen (z. B. die Aortengeometrie der Ldlr-/-Maus mit dem Lipidprofil der Apoe-/- Maus) analysiert und die daraus resultierende Plaqueentwicklung und -Zusammensetzung simuliert werden. Dies könnte zum Verständnis des komplexen Zusammenspiels zwischen veränderter Hämodynamik, Serumlipiden und Atherosklerose beitragen und unser grundlegendes Verständnis der Schlüsselfaktoren für die Entstehung von Atherosklerose deutlich verbessern. In Kapitel 5 wird die Etablierung eines tissue-engineerten Arterienmodells beschrieben, das auf nativen, von Schweinehalsschlagadern hergestellten, dezellularisierten Gerüststrukturen basiert. Diese wurden zudem in einem MRT-geeigneten Bioreaktorsystem [23] kultiviert, um die hämodynamisch bedingte Atheroskleroseentwicklung auf kontrollierbare Weise zu untersuchen, wobei hierfür die zuvor etablierten Methoden zur WSS- und PWV-Bewertung [4, 16] verwendet wurden. Dieses in vitro Arterienmodell zielte auf die Reduzierung von Tierversuchen ab und bot gleichzeitig eine vereinfachte, aber vollständig kontrollierbare physikalische und biologische Umgebung. Zu diesem Zweck wurde in einem ersten Schritt ein sehr schnelles und schonendes Dezellularisierungsverfahren etabliert, das zu Gerüststrukturen basierend auf Schweinehalsschlagadern führte, die eine vollständige Azellularität aufwiesen, wobei gleichzeitig die Zusammensetzung der extrazellulären Matrix, die allgemeine Ultrastruktur und die mechanischen Eigenschaften der nativen Arterien erhalten blieben. Darüber hinaus wurde eine gute Zelladhäsion und -proliferation erreicht, die mit isolierten menschlichen Endothelzellen aus humanem Vollblut untersucht wurde. Darüber hinaus wurde zum ersten Mal eine MRT-geeignete Arterienkammer für die gleichzeitige Kultivierung der generierten Modelle und der Untersuchung der hochauflösenden 4D-Hämodynamik in diesen Arterienmodellen entwickelt. Unter Verwendung der hochauflösenden 4D-Fluss-MRT erwies sich das Bioreaktorsystem als sehr geeignet, den Volumenstrom, die beiden Komponenten der WSS inklusive dem radialen Druck und die PWV in den Arterienmodellen zu quantifizieren, wobei die erhaltenen Werte sehr gut mit den in der Literatur gefundenen Werten für in vivo-Messungen vergleichbar sind. Darüber hinaus lassen sich durch die dreidimensionale Untersuchung der Gefäßwandmorphologie in den in vitro-Modellen erste atherosklerotische Prozesse wie die Verdickung der Intima erkennen. Eine Einschränkung ist jedoch das Fehlen einer medialen glatten Muskelzellschicht aufgrund der dichten ECM des Gewebegerüsts. Die Verwendung der Laserschneidetechnik zur Erzeugung von Löchern und / oder Gruben im Mikrometerbereich, die eine Besiedlung des Mediums mit SMCs ermöglichen, zeigte in einem ersten Versuch vielversprechende Ergebnisse und sollte in zukünftigen Studien daher dringend weiter untersucht werden. Das präsentierte Arterienmodell verfügt somit über alle relevanten Komponenten für die Erweiterung zu einem Atherosklerosemodell und ebnet den Weg für ein deutlich besseres Verständnis der Schlüsselmechanismen in der Atherogenese. Kapitel 6 beschreibt die Entwicklung eines einfach herzustellenden, kostengünstigen und vollständig an gegebene Bedürfnisse anpassbaren Arterienmodells auf Grundlage von Biomaterialien. Hier wurden thermoresponsive Opfergerüststrukturen, die mit der MEW-Technik hergestellt wurden, zur Herstellung variabler, biomimetischer Formen verwendet, um die geometrischen Eigenschaften des Aortenbogens, bestehend aus Verzweigungen und Krümmungen, zu imitieren. Nach der Einbettung der Opfergerüststruktur in ein Gelatin-Hydrogel, das zudem SMCs enthält, wurde es mit bakterieller Transglutaminase vernetzt, bevor es aufgelöst und gespült wurde. Der so entstandene Hydrogelkanal wurde anschließend mit Endothelzellen besiedelt, wodurch ein einfach zu erstellendes, schnelles und kostengünstiges Arterienmodell entstand. Im Gegensatz zum nativen Arterienmodell ist dieses Modell daher deutlich variabler in Größe und Form und bietet die wichtige Möglichkeit, von Anfang an glatte Muskelzellen mit einzubringen. Darüber hinaus wurde speziell für die gegebene Gerüststruktur eine maßgeschneiderte und hochgradig anpassungsfähige Perfusionskammer entwickelt, die eine sehr schnelle und einstufige Herstellung des Arterienmodells ermöglicht und gleichzeitig die Möglichkeit zur dynamischen Kultivierung der Modelle bietet, was eine hervorragende Grundlage für die Entwicklung von in vitro Krankheits-Testsystemen für z.B. die Atheroskleroseforschung im Zusammenhang mit der Hämodynamik darstellt. Aus Zeitgründen konnte die Ausweitung auf ein Atherosklerosemodell jedoch im Rahmen dieser Arbeit nicht realisiert werden. Daher werden sich zukünftige Studien auf die Entwicklung und Validierung eines in vitro-Atherosklerosemodells konzentrieren, das auf den hier entwickelten zwei- und dreischichtigen Arterienmodellen basiert. Zusammenfassend lässt sich sagen, dass diese Arbeit den Weg für eine schnelle Erfassung und detaillierte Analyse der sich verändernden Hämodynamik während der Entwicklung und der Progression der Atherosklerose geebnet hat, einschließlich räumlich aufgelöster Analysen aller relevanten hämodynamischen Parameter im Zeitverlauf innerhalb einer Gruppe und zwischen verschiedenen Gruppen. Darüber hinaus wurden vielversprechende Arterienmodelle etabliert, die das Potenzial haben, als neue Plattform für die Atherosklerose-Grundlagenforschung zu dienen, um Tierversuche zu minimieren und gleichzeitig die Kontrolle über verschiedene Parameter zu erlangen, die die Atheroskleroseentwicklung beeinflussen. KW - Hämodynamik KW - Arteriosklerose KW - Tissue Engineering KW - Atherosclerosis KW - MRI KW - Hemodynamics KW - Tissue Engineering KW - Biofabrication KW - Artery Models Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-303601 ER - TY - THES A1 - Vogt, Fabian T1 - Elektrochemisch abgeschiedenes Calciumhydroxid Ca(OH)\(_2\) als antibakterielle, antiinflammatorische und proosseointegrative Titanimplantat-Oberflächen-Modifikation im In vivo Versuch T1 - Electrochemically deposited calcium hydroxide Ca(OH)\(_2\) as an antibacterial, anti-inflammatory and proosseointegrative titanium implant surface modification in an in vivo experiment N2 - Das Ziel der experimentellen Studie war die Erprobung der (bereits in vitro erfolgreich getesteten) Ca(OH)2-Beschichtung In vivo unter dem Aspekt, ob und inwieweit die antibakteriellen und somit auch antiinflammatorischen bzw. entzündungsmoderierenden Eigenschaften der Ca(OH)2-Beschichtung eine sinnvolle und effektive Ergänzung zu den bisher erfolgreich eingesetzten Calciumphosphat(CaP)-Beschichtungen mit bewiesenen, guten proosseointegrativen Eigenschaften bei lasttragenden Implantaten sein können. Zusammenfassend kann festgestellt werden, dass die Ergebnisse der In vitro Untersuchung durch die In vivo Versuche in den Bereichen 0-100 KBE grundsätzlich als gestützt gelten können. Die Zuverlässigkeit der Wirkung durch Ca(OH)2 nimmt jedoch mit steigender KBE-Zahl ab, sodass weitere Testreihen sinnvoll sind. N2 - The aim of the experimental study was to test the Ca(OH)2-coating (which has already been successfully tested in vitro) in vivo under the aspect of whether and to what extent the antibacterial and thus also anti-inflammatory or inflammation-moderating properties of the Ca(OH)2-coating can be a useful and effective addition to the common successfully used calcium phosphate (CaP)-coatings with proven, good proosseointegrative properties in load-bearing implants. In summary, it can be stated that the results of the in vitro investigation can generally be considered supported through the in vivo tests in the range of 0 -100 CFU. However, the reliability of the effect caused by Ca(OH)2 decreases as the CFU number increases, so further series of tests make sense. KW - Calciumhydroxid KW - Implantat KW - In vivo KW - antibakteriell KW - antiinflammatorisch KW - proosseointegrativ KW - S.aureus KW - Tierversuch KW - Titan Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-346343 ER - TY - THES A1 - Mittmann, Silvia T1 - Etablierung von Hydroxylapatit-Prüfkörpern zur in-vitro Qualifizierung von Knochenklebern T1 - Establishment of hydroxyapatite test specimens for in vitro qualification of bone adhesives N2 - Im Rahmen dieser Arbeit sollte herausgefunden werden, inwiefern Calciumorthophosphatzemente (CPC) dafür geeignet sind, um als Prüfkörper zur Qualifizierung von Knochenklebern zu dienen, und worin ihre Limitationen bestehen. Dazu sollte nicht nur ein materieller Vergleich verschiedener hydroxylapatitbildender Zemente mit Knochen erfolgen. Es sollte auch das Adhäsionsverhalten neuartiger Knochenkleber auf den verschiedenen Prüfkörpermaterialien verglichen werden, um mögliche Rückschlüsse für die Eignung als standardisierbares in-vitro Prüfkörpermaterial ziehen zu können. Gegenstand der Untersuchung war ein α-Tricalciumphosphat (α-TCP)-System und ein Tetracalciumphosphat (TTCP)-System welche im Rahmen einer Zement-Abbindereaktion calciumdefizitären Hydroxylapatit (CDHA) bzw. stöchiometrischen Hydroxylapatit (HA) bilden. Die Materialien wurden dazu verwendet Prüfkörperteile in Form von Zylindern (5 x 5 mm) und Plättchen (20 x 10 x 5 mm) herzustellen, die dann mit verschiedenen Knochenklebern verklebt werden konnten. Der stärkste der verwendeten Kleber war ein Cyanoacrylat-Kleber (Truglue®). Er erzielte auf Prüfkörpern aus Knochen nach 24-stündiger Lagerung in PBS mittlere Abscherfestigkeiten von ca. 4,22 ± 1,92 MPa. Als zweitstärkster Kleber erwies sich ein neuartiger zementbasierter Kleber, der aus wärmebehandeltem Trimagnesiumphosphat-Hydrat und Phosphoserin bestand. Dieser Kleber erzielte unter den gleichen Umständen mittlere Abscherfestigkeiten von ca. 1,89 ± 0,29 MPa. Etwas schwächer schnitt ein ebenfalls neuartiger zementbasierter Kleber ab, der aus dem Magnesiumphosphat Farringtonit, sowie aus Magnesiumoxid und 25 % Phytinsäure bestand. Dieser Kleber erzielte mittlere Abscherfestigkeiten von ca. 0,51 ± 0,16 MPa. Insgesamt haben die Untersuchungen gezeigt, dass die in-vitro Qualifizierung von Knochenklebern unter Verwendung von Prüfkörpern aus Zement möglich wäre. Die Prüfkörper aus CDHA vereinten die meisten Vorteile und wären für Klebesysteme mit Abscherfestigkeiten von bis zu 2 MPa geeignet. Dabei erzeugten die Knochenkleber auf CDHA zwar abweichende Abscherfestigkeiten als auf Knochen, doch ließ sich ein vergleichbarer Trend bei stets reduzierten Varianzen erkennen. Durch die gute Konsistenz der Zementpaste war die Herstellung homogener Prüfkörper möglich. Aufgrund der Stabilität von CDHA unter wässrigen Bedingungen konnten Langzeitversuche ohne Einschränkungen vorgenommen werden. Die Limitationen der Prüfkörper aus CDHA bestanden allerdings darin, dass sie nicht für Abscherversuche von stärkeren Klebern geeignet waren. In solchen Fällen versagten die Prüfkörper noch bevor die maximale Abscherfestigkeit des jeweiligen Klebers gemessen werden konnte. N2 - Until now, in vitro qualification of bone adhesives was mostly performed on bone test specimens of animal origin. The work dealt with the question to what extent test specimens made of synthetic hydroxyapatite would be suitable for the in vitro qualification of bone adhesives. For this purpose, test specimens were prepared from an a-TCP cement system and a TTCP cement system and compared with each other. The shear strengths of various novel bone adhesives were tested on the synthetic test specimens after different time intervals. KW - Knochenersatz KW - Knochenkleber Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-299140 ER - TY - THES A1 - Weichhold, Jan Lukas T1 - Injectable calcium phosphate-based bone replacement cements T1 - Injizierbare calciumphosphat-basierte Knochenersatzzemente N2 - The human body has very good self-healing capabilities for numerous different injuries to a variety of different tissues. This includes the main human mechanical framework, the skeleton. The skeleton is limited in its healing without additional aid by medicine mostly by the defect size. When the defect reaches a size above 2.5 cm the regeneration of the defect ends up faulty. Here is where implants, defect fillers and other support approaches developed in medicine can help the body to heal the big defect still successfully. Usually sturdy implants (auto-/allo-/xenogenic) are implanted in the defect to bridge the distance, but for auto- and allogenic implants a suitable donor site must be found and for all sources the implant needs to be shaped into the defect specific site to ensure a perfect fit, the best support and good healing. This shaping is very time consuming and prone to error, already in the planning phase. The use of a material that is moldable and sets in the desired shape shortly after applying negates these disadvantages. Cementitious materials offer exactly this property by being in a pasty stage after the powder and liquid components have been mixed and the subsequently hardening to a solid implant. These properties also enable the extrusion, and therefore may also enable the injection, of the cement via a syringe in a minimal invasive approach. To enable a good injection of the cement modifications are necessary. This work aimed to modify commonly used calcium phosphate-based cement systems based on α-TCP (apatitic) and β-TCP (brushitic). These have been modified with sodium phytate and phytic acid, respectively. Additionally, the α-TCP system has been modified with sodium pyrophosphate, in a second study, to create a storable aqueous paste that can be activated once needed with a highly concentrated sodium orthophosphate solution. The powder phase of the α-TCP cement system consisted of nine parts α-TCP and one part CDHA. These were prepared to have different particle sizes and therefore enable a better powder flowability through the bimodal size distribution. α-TCP had a main particle size of 20 μm and CDHA of 2.6 μm. The modification with sodium phytate led to an adsorption of phytate ions on the surface of the α-TCP particles, where they started to form complexes with the Ca2+ ions in the solution. This adsorption had two effects. The first was to make the calcium ions unavailable, preventing supersaturation and ultimately the precipitation of CDHA what would lead to the cement hardening. The second was the increase of the absolute value of the surface charge, zeta potential, of the powder in the cement paste. Here a decrease from +3 mV to -40 mV could be measured. A strong value for the zeta potential leads to a higher repulsion of similarly charged particles and therefore prevents powder agglomeration and clogging on the nozzle during injection. These two modifications (bimodal particles size distribution and phytic acid) lead to a significant increase in the paste injectability. The unmodified paste was injectable for 30 % only, where all modified pastes were practically fully injectable ~90 % (the residual paste remained in the nozzle, while the syringe plunger already reached the end of the syringe). A very similar observation could be made for the β-TCP system. This system was modified with phytic acid. The zeta potential was decreased even stronger from -10 ± 1.5 mV to -71.5 ± 12 mV. The adsorption of the phytate ions and subsequent formation of chelate complexes with the newly dissolved Ca2+ ions also showed a retarding effect in the cements setting reaction. Where the unmodified cement was not measurable in the rheometer, as the reaction was faster than the measurement setup (~1.5 min), the modified cements showed a transition through the gel point between 3-6 min. This means the pastes stayed between 2 and 4 times longer viscous than without the modification. Like with the first cement system also here the effects of the phytate addition showed its beneficial influence in the injectability measurement. The unmodified cement was not injectable at all, due to the same issue already encountered at the rheology measurements, but all modified pastes were fully injectable for at least 5 min (lowest phytate concentration) and at least 10 min (all other concentrations) after the mixing of powder and liquid. The main goal of the last modification with sodium pyrophosphate was to create a paste that was stable in aqueous environment without setting until the activation takes place, but it should still show good injectability as this was the desired way of application after activation. Like before also the zeta potential changed after the addition of pyrophosphate. It could be lowered from -22 ± 2mV down to -61 to -68 ± 4mV (depending on the pyrophosphate concentration). The pastes were stored in airtight containers at room temperature and checked for their phase composition over 14 days. The unmodified paste showed a beginning phase conversion to hydroxyapatite between 7 and 14 days. All other pastes were still stable and unreacted. The pastes were activated with a high concentrated (30 wt%) sodium orthophosphate solution. After the activation the pastes were checked for their injectability and showed an increase from -57 ± 11% for the unmodified paste to -89 ± 3% (practically fully injectable as described earlier) for the best modified paste (PP005). It can be concluded that the goal of enabling full injection of conventional calcium phosphate bone cement systems was reached. Additional work produced a storage stable paste that still ensures full injectability. Subsequent work already used the storable paste and modified it with hyaluronic acid to create an ink for 3D extrusion printing. The first two cement systems have also already been investigated in cell culture for their influence on osteoblasts and osteoclasts. The next steps would have to go more into the direction of translation. Figuring out what properties still need to be checked and where the modification needs adjustment to enable a clinical use of the presented systems. N2 - Der menschliche Körper verfügt über sehr gute Selbstheilungsfähigkeiten für zahlreiche verschiedene Verletzungen in unterschiedlichen Geweben. Dazu gehört auch das wichtigste mechanische Gerüst des Menschen, das Skelett. Das Skelett ist in seiner Heilung ohne zusätzliche Hilfe durch die Medizin vor allem durch die Defektgröße begrenzt. Erreicht der Defekt eine Größe von mehr als 2,5 cm, ist die Regeneration des Defekts nicht mehr gewährleistet. Hier können Implantate, Defektfüller und andere in der Medizin entwickelte Unterstützungsansätze dem Körper helfen, den großen Defekt noch erfolgreich zu heilen. In der Regel werden stabile Implantate (auto-/allo-/xenogen) in den Defekt eingesetzt, um den Abstand zu überbrücken. Für auto- und allogene Implantate muss jedoch eine geeignete Spenderstelle gefunden werden, und für alle Quellen muss das Implantat in die defektspezifische Stelle geformt werden, um eine perfekte Passform, den besten Halt und eine gute Heilung zu gewährleisten. Diese Formgebung ist sehr zeitaufwendig und fehleranfällig, schon in der Planungsphase. Die Verwendung eines Materials, das formbar ist und kurz nach dem Auftragen in der gewünschten Form aushärtet, negiert diese Nachteile. Zementartige Materialien bieten genau diese Eigenschaft, indem sie sich nach dem Vermischen von Pulver und flüssigen Komponenten in einem pastösen Stadium befinden und anschließend zu einem festen Implantat aushärten. Diese Eigenschaften ermöglichen auch die Extrusion und damit möglicherweise auch die Injektion des Zements über eine Spritze in einem minimalinvasiven Verfahren. Um eine gute Injektion des Zements zu ermöglichen, sind Modifikationen erforderlich. Ziel dieser Arbeit war es, die gängigen Zementsysteme auf Kalziumphosphatbasis zu modifizieren, die auf α-TCP (apatitisch) und β-TCP (brushitisch) basieren. Diese wurden mit Natriumphytat bzw. Phytinsäure modifiziert. Zusätzlich wurde das α-TCP-System in einer zweiten Studie mit Natriumpyrophosphat modifiziert, um eine lagerfähige wasserbasierte Paste zu schaffen, die bei Bedarf mit einer hochkonzentrierten Natriumorthophosphatlösung aktiviert werden kann. Die Pulverphase des α-TCP-Zementsystems bestand aus neun Teilen α-TCP und einem Teil CDHA. Diese wurden so aufbereitet, dass sie unterschiedliche Partikelgrößen aufweisen und somit eine bessere Fließfähigkeit des Pulvers durch die bimodale Größenverteilung ermöglichen. α-TCP hatte eine Hauptpartikelgröße von 20 μm und CDHA von 2,6 μm. Die Modifizierung mit Natriumphytat führte zu einer Adsorption von Phytat-Ionen an der Oberfläche der α-TCP-Partikel, wo sie Komplexe mit den Ca2+-Ionen in der Lösung zu bilden begannen. Diese Adsorption hatte zwei Auswirkungen. Die erste bestand darin, dass die Calciumionen nicht mehr verfügbar waren, wodurch die Übersättigung und letztlich die Ausfällung von CDHA verhindert wurde, was zur Erhärtung des Zements geführt hätte. Der zweite Effekt war die Erhöhung des Betrags der Oberflächenladung, des Zetapotenzials, des Pulvers in der Zementpaste. Hier konnte eine Abnahme von +3 mV auf -40 mV gemessen werden. Ein hoher Wert für das Zetapotenzial führt zu einer stärkeren Abstoßung ähnlich geladener Teilchen und verhindert somit die Agglomeration des Pulvers und das Verstopfen der Kanüle während der Injektion. Diese beiden Modifikationen (bimodale Partikelgrößenverteilung und Phytinsäure) führen zu einer deutlichen Verbesserung der Injektionsfähigkeit der Paste. Die unmodifizierte Paste war nur zu 30 % injizierbar, während alle modifizierten Pasten praktisch vollständig injizierbar waren ~90 %(die Restpaste blieb in der Kanüle, während der Spritzenkolben bereits das Ende der Spritze erreichte). Eine sehr ähnliche Beobachtung konnte für das β-TCP-System gemacht werden. Dieses System wurde mit Phytinsäure modifiziert. Das Zetapotenzial sank noch stärker von -10 ± 1,5 mV auf -71,5 ± 12mV. Die Adsorption der Phytat-Ionen und die anschließende Bildung von Chelatkomplexen mit den neu gelösten Ca2+-Ionen zeigten ebenfalls eine verzögernde Wirkung bei der Abbindereaktion des Zements. Während der unmodifizierte Zement im Rheometer nicht messbar war, da die Reaktion schneller verlief als der Messaufbau (~1,5 min), zeigten die modifizierten Zemente einen Übergang durch den Gelpunkt zwischen 3-6 min. Dies bedeutet, dass die Pasten zwischen 2 und 4 mal länger viskos blieben als ohne die Modifikation. Wie beim ersten Zementsystem zeigte sich auch hier der positive Einfluss des Phytatzusatzes bei der Messung der Injektionsfähigkeit. Der unmodifizierte Zement war überhaupt nicht injizierbar, was auf das gleiche Problem zurückzuführen ist, das bereits bei den rheologischen Messungen aufgetreten ist, aber alle modifizierten Pasten waren mindestens 5 min (niedrigste Phytatkonzentration) und mindestens 10 min (alle anderen Konzentrationen) nach dem Mischen von Pulver und Flüssigkeit vollständig injizierbar. Das Hauptziel der letzten Modifikation mit Natriumpyrophosphat bestand darin, eine Paste zu schaffen, die in wässriger Umgebung stabil ist und bis zur Aktivierung nicht aushärtet, die aber dennoch eine gute Injektionsfähigkeit aufweisen sollte, da dies die gewünschte Art der Anwendung nach der Aktivierung war. Wie zuvor änderte sich auch das Zetapotenzial nach der Zugabe von Pyrophosphat. Es konnte von -22 ± 2mV auf -61 bis -68 ± 4mV (abhängig von der Pyrophosphatkonzentration) gesenkt werden. Die Pasten wurden in luftdichten Behältern bei Raumtemperatur gelagert und über 14 Tage auf ihre Phasenzusammensetzung untersucht. Die unmodifizierte Paste zeigte zwischen 7 und 14 Tagen eine beginnende Phasenumwandlung in Hydroxyapatit. Alle anderen Pasten waren noch stabil und nicht umgewandelt. Die Pasten wurden mit einer hochkonzentrierten (30 Gew.-%) Natriumorthophosphatlösung aktiviert. Nach der Aktivierung wurden die Pasten auf ihre Injektionsfähigkeit geprüft und zeigten einen Anstieg von -57 ± 11 % für die unmodifizierte Paste auf -89 ± 3 % (praktisch vollständig injizierbar, wie zuvor beschrieben) für die beste modifizierte Paste (PP005). Daraus lässt sich schließen, dass das Ziel, die vollständige Injektion herkömmlicher Kalziumphosphat-Knochenzementsysteme zu ermöglichen, erreicht wurde. Weitere Arbeiten führten zu einer lagerstabilen Paste, die dennoch eine vollständige Injektionsfähigkeit gewährleistet. In nachfolgenden Arbeiten wurde die lagerfähige Paste bereits verwendet und mit Hyaluronsäure modifiziert, um eine Tinte für den 3D-Extrusionsdruck herzustellen. Die ersten beiden Zementsysteme wurden auch bereits in Zellkulturen auf ihren Einfluss auf Osteoblasten und Osteoklasten untersucht. Die nächsten Schritte müssten mehr in Richtung Translation gehen. Es gilt herauszufinden, welche Eigenschaften noch überprüft werden müssen und wo die Modifikation angepasst werden muss, um einen klinischen Einsatz der vorgestellten Systeme zu ermöglichen. KW - Calciumphosphat KW - Cement KW - Knochenersatz KW - Zement KW - Injectability KW - Bone-replacement KW - IP6 KW - Modification KW - Rheology KW - Setting Control KW - Calcium Phosphate Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-326616 ER - TY - THES A1 - Renner, Tobias T1 - Neue adhäsive mineral-organische Knochenzemente auf Basis von Phosphoserin und Magnesiumphosphaten bzw. -oxiden T1 - Novel adhesive mineral-organic bone cements based on phosphoserine and magnesium phosphates or oxides N2 - Heutige chirurgische Situationen können zeitweise den Einsatz eines Knochenkleber erfordern, welcher sich jedoch noch nicht in der klinischen Praxis etablieren konnte. In jüngster Vergangenheit haben mit Phosphoserin modifizierte Zemente (PMC) auf der Grundlage von Verbindungen zwischen o-Phosphoserin (OPLS) und Calciumphosphaten wie Tetracalciumphosphat (TTCP) oder α-Tricalciumphosphat (α-TCP) an Popularität gewonnen. Ebenso bekommen chelatbildende Magnesiumphosphatzemente als mineralische Knochenadhäsive mehr Zuspruch. In dieser Arbeit wurden neue mineralorganische Knochenzemente auf der Basis von Phosphoserin und Magnesiumphosphaten oder -oxiden untersucht, die hervorragende Hafteigenschaften besitzen. Diese wurden mittels Röntgenbeugung, Fourier-Infrarot-Spektroskopie und Elektronenmikroskopie analysiert und mechanischen Tests unterzogen, um die Haftfestigkeit am Knochen nach Alterung unter physiologischen Bedingungen zu bestimmen. Die neuartigen biomineralischen Klebstoffe zeigen eine ausgezeichnete Haftfestigkeit an Knochen mit etwa 6,6-7,3 MPa unter Scherbelastung. Die Adhäsive sind auch aufgrund ihres kohäsiven Versagensmusters und ihres duktilen Charakters vielversprechend. In diesem Zusammenhang sind die neuen adhäsiven Zemente den derzeit vorherrschenden Knochenadhäsiven überlegen. Ergänzend wurde versucht, dieses neue System mit unterschiedlichen Additiven zu modifizieren. Dabei wurde Mannit erfolgreich als Porogen verwendet. Dreiarmiges sternförmiges NCO-sP(EO-stat-PO) sollte die adhäsiven Eigenschaften und das Leistungspotenzial unter Wasser verbessern. Zuletzt wurden mit Glycerol präfabrizierte Pasten hergestellt, welche gelagert werden können und bei Kontakt mit Wasser aushärten. Generell ist zu betonen, dass künftige Bemühungen um Knochenklebstoffe aus Phosphoserin und Mg2+ sehr lohnenswert erscheinen. N2 - Present surgical situations require a bone adhesive which has not yet been developed for use in clinical applications. Recently, phosphoserine modified cements (PMC) based on mixtures of o-phosphoserine (OPLS) and calcium phosphates, such as tetracalcium phosphate (TTCP) or α-tricalcium phosphate (α-TCP) as well as chelate setting magnesium phosphate cements have gained increasing popularity for their use as mineral bone adhesives. Here, we investigated new mineral-organic bone cements based on phosphoserine and magnesium phosphates or oxides, which possess excellent adhesive properties. These were analyzed by X-ray diffraction, Fourier infrared spectroscopy and electron microscopy and subjected to mechanical tests to determine the bond strength to bone after ageing at physiological conditions. The novel biomineral adhesives demonstrate excellent bond strength to bone with approximately 6.6–7.3 MPa under shear load. The adhesives are also promising due to their cohesive failure pattern and ductile character. In this context, the new adhesive cements are superior to currently prevailing bone adhesives. In addition, an attempt was made to modify this new system with different additives. Mannite was successfully used as a porogen. Three-armed star-shaped NCO-sP(EO-stat-PO) should improve the adhesive properties and performance potential under water. Last glycerol-prefabricated pastes were prepared, which could be stored and cure upon contact with water. In general, it should be emphasized that future efforts on bone adhesives from phosphoserine and Mg2+ seem very worthwhile. KW - Phosphoserin KW - Klebstoff KW - Magnesiumphosphate KW - Knochenzement KW - Magnesiumoxid KW - bone adhesive KW - bone glue KW - magnesium phosphate cement KW - organophosphates KW - bone cement Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-323210 ER - TY - THES A1 - Gefel, Eugen T1 - Zelluläre Resorption 3D-gedruckter Knochenimplantate auf Basis von Calciummagnesiumphosphaten T1 - Cellular resorption of 3D-printed bone implants based on calcium magnesium phosphates N2 - Für die Behandlung von Knochendefekten kritischer Größe gibt es heute eine Reihe von Therapiemöglichkeiten. Neuartige Ansätze mit Magnesiumphosphat- (MPC) und Calciummagnesiumphosphatzementen (CMPC) haben sich als echte Alternativen zu den etablierten Calciumphosphaten erwiesen. Ziel war es, die Osteoklastogenese in vitro auf 3D-pulvergedrucktem CMPC und MPC zu induzieren und die zelluläre Resorption (zR) zu analysieren. Polystyrol (PS), Glas, β-TCP und Brushit-bildender Zement dienten als Referenzen. Als Proben wurden Zemente der allgemeinen stöchiometrischen Summenformel CaxMg(3–x)(PO4)2 (x = 0; 0,25; 0,75; 3) verwendet, die Struvit oder Newberyit enthielten. Für die Osteoklastogenese wurden monozytenangereicherte PBMCs aus Buffy-Coat mittels dreifacher Dichtegradientenzentrifugation isoliert, auf die Prüfoberflächen ausgesät und über einen Zeitraum von 22 Tagen mit Zytokinen (M-CSF und RANKL) stimuliert. Die Interaktion der Zellen mit den Zementen bzw. PS/Glas wurde mittels TRAP-Färbung und -Aktivität, DNA- und Ionenkonzentrationen (Ca2+, Mg2+, PO43–, pH-Wert), Rasterelektronen-, Durchlicht-, Auflicht- und Fluoreszenzmikroskopie analysiert. Auf den Struvit- und Newberyit-bildenden Zementen konnten keine für Osteoklasten typischen Riesenzellen nachgewiesen werden. Auf den Struvit-bildenden Zementen wurde deutlich mehr mononukleäre Zellen nachgewiesen wurden als auf den Newberyit-bildenden Zementen. Während die Freisetzung von Mg2+ und PO43– ausschließlich durch die chemische Degradation erfolgte, wurde Ca2+ zunächst adsorbiert und anschließend durch zR freigesetzt. Die erhöhte Ca2+-Adsorption im Vergleich zur Ca2+-Resorption führte insgesamt zu einer Calcium-Präzipitation. Da lediglich auf β-TCP Resorptionslakunen beobachtet wurden, wird angenommen, dass auf den CMPC, MPC und Brushite-bildenden Zementen die zellvermittelte Ca2+-Freisetzung von den Präzipitaten ausging, die von Makrophagen auf den Zementen und/oder Riesenzellen auf den Wellplatten resorbiert wurden. N2 - There are a number of therapeutic options available today for the treatment of critical size bone defects. Novel approaches using magnesium phosphate (MPC) and calcium magnesium phosphate cements (CMPC) have proven to be real alternatives to the established calcium phosphates. The aim was to induce osteoclastogenesis in vitro on 3D powder-printed CMPC and MPC and to analyse cellular resorption (zR). Polystyrene (PS), glass, β-TCP and brushite-forming cement served as references. Cements of the general stoichiometric molecular formula CaxMg(3-x)(PO4)2 (x = 0; 0.25; 0.75; 3) containing struvite or newberyite were used as samples. For osteoclastogenesis, monocyte-enriched PBMCs were isolated from buffy coat by triple density gradient centrifugation, seeded onto the test surfaces and stimulated with cytokines (M-CSF and RANKL) over a period of 22 days. The interaction of the cells with the cements or PS/glass was analysed by TRAP staining and activity, DNA and ion concentrations (Ca2+, Mg2+, PO43-, pH), SEM, transmitted light, reflected light and fluorescence microscopy. No giant cells typical of osteoclasts could be detected on the struvite- and newberyite-forming cements. On the struvite-forming cements, significantly more mononuclear cells were detected than on the newberyite-forming cements. While the release of Mg2+ and PO43- was exclusively by chemical degradation, Ca2+ was first adsorbed and then released by zR. The increased Ca2+ adsorption compared to Ca2+ resorption led to calcium precipitation overall. Since resorption lacunae were only observed on β-TCP, it is assumed that on the CMPC, MPC and Brushite-forming cements, the cell-mediated Ca2+ release originated from the precipitates resorbed by macrophages on the cements and/or giant cells on the well plates. KW - Knochenzement KW - Osteoklast KW - Struvit KW - Calciumphosphat KW - Magnesiumphosphate KW - Newberyit KW - Calciummagnesiumphosphat KW - Bioresorption KW - 3D Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-322248 ER - TY - JOUR A1 - Janzen, Dieter A1 - Bakirci, Ezgi A1 - Faber, Jessica A1 - Andrade Mier, Mateo A1 - Hauptstein, Julia A1 - Pal, Arindam A1 - Forster, Leonard A1 - Hazur, Jonas A1 - Boccaccini, Aldo R. A1 - Detsch, Rainer A1 - Teßmar, Jörg A1 - Budday, Silvia A1 - Blunk, Torsten A1 - Dalton, Paul D. A1 - Villmann, Carmen T1 - Reinforced Hyaluronic Acid-Based Matrices Promote 3D Neuronal Network Formation JF - Advanced Healthcare Materials N2 - 3D neuronal cultures attempt to better replicate the in vivo environment to study neurological/neurodegenerative diseases compared to 2D models. A challenge to establish 3D neuron culture models is the low elastic modulus (30–500 Pa) of the native brain. Here, an ultra-soft matrix based on thiolated hyaluronic acid (HA-SH) reinforced with a microfiber frame is formulated and used. Hyaluronic acid represents an essential component of the brain extracellular matrix (ECM). Box-shaped frames with a microfiber spacing of 200 µm composed of 10-layers of poly(ɛ-caprolactone) (PCL) microfibers (9.7 ± 0.2 µm) made via melt electrowriting (MEW) are used to reinforce the HA-SH matrix which has an elastic modulus of 95 Pa. The neuronal viability is low in pure HA-SH matrix, however, when astrocytes are pre-seeded below this reinforced construct, they significantly support neuronal survival, network formation quantified by neurite length, and neuronal firing shown by Ca\(^{2+}\) imaging. The astrocyte-seeded HA-SH matrix is able to match the neuronal viability to the level of Matrigel, a gold standard matrix for neuronal culture for over two decades. Thus, this 3D MEW frame reinforced HA-SH composite with neurons and astrocytes constitutes a reliable and reproducible system to further study brain diseases. KW - 3D model systems KW - melt electrowriting KW - cortical neurons KW - astrocytes KW - Ca\(^{2+}\)-Imaging KW - hyaluronic acid Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318682 VL - 11 IS - 21 ER - TY - JOUR A1 - Lamberger, Zan A1 - Zainuddin, Shakir A1 - Scheibel, Thomas A1 - Lang, Gregor T1 - Polymeric Janus Fibers JF - ChemPlusChem N2 - Janus fibers are a class of composite materials comprising mechanical and chemical to biological functionality. Combining different materials and functionalities in one micro- or even nanoscale fiber enables otherwise unreachable synergistic physicochemical effects with unprecedented opportunities for technical or biomedical applications. Here, recent developments of processing technologies and applications of polymeric Janus fibers will be reviewed. Various examples in the fields of textiles, catalysis, sensors as well as medical applications, like drug delivery systems, tissue engineering and antimicrobial materials, are presented to illuminate the outstanding potential of such high-end functional materials for novel applications in the upcoming future. KW - hybrid materials KW - polymers KW - nanofibers KW - spinning KW - Janus fibers Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318516 VL - 88 IS - 2 ER - TY - JOUR A1 - Kade, Juliane C. A1 - Bakirci, Ezgi A1 - Tandon, Biranche A1 - Gorgol, Danila A1 - Mrlik, Miroslav A1 - Luxenhofer, Robert A1 - Dalton, Paul D. T1 - The Impact of Including Carbonyl Iron Particles on the Melt Electrowriting Process JF - Macromolecular Materials and Engineering N2 - Melt electrowriting, a high-resolution additive manufacturing technique, is used in this study to process a magnetic polymer-based blend for the first time. Carbonyl iron (CI) particles homogenously distribute into poly(vinylidene fluoride) (PVDF) melts to result in well-defined, highly porous structures or scaffolds comprised of fibers ranging from 30 to 50 µm in diameter. This study observes that CI particle incorporation is possible up to 30 wt% without nozzle clogging, albeit that the highest concentration results in heterogeneous fiber morphologies. In contrast, the direct writing of homogeneous PVDF fibers with up to 15 wt% CI is possible. The fibers can be readily displaced using magnets at concentrations of 1 wt% and above. Combined with good viability of L929 CC1 cells using Live/Dead imaging on scaffolds for all CI concentrations indicates that these formulations have potential for the usage in stimuli-responsive applications such as 4D printing. KW - additive manufacturing KW - melt electrospinning writing KW - magnetoactive materials KW - electroactive polymers Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318482 SN - 1438-7492 VL - 307 IS - 12 ER - TY - JOUR A1 - Ryma, Matthias A1 - Genç, Hatice A1 - Nadernezhad, Ali A1 - Paulus, Ilona A1 - Schneidereit, Dominik A1 - Friedrich, Oliver A1 - Andelovic, Kristina A1 - Lyer, Stefan A1 - Alexiou, Christoph A1 - Cicha, Iwona A1 - Groll, Jürgen T1 - A Print-and-Fuse Strategy for Sacrificial Filaments Enables Biomimetically Structured Perfusable Microvascular Networks with Functional Endothelium Inside 3D Hydrogels JF - Advanced Materials N2 - A facile and flexible approach for the integration of biomimetically branched microvasculature within bulk hydrogels is presented. For this, sacrificial scaffolds of thermoresponsive poly(2-cyclopropyl-2-oxazoline) (PcycloPrOx) are created using melt electrowriting (MEW) in an optimized and predictable way and subsequently placed into a customized bioreactor system, which is then filled with a hydrogel precursor solution. The aqueous environment above the lower critical solution temperature (LCST) of PcycloPrOx at 25 °C swells the polymer without dissolving it, resulting in fusion of filaments that are deposited onto each other (print-and-fuse approach). Accordingly, an adequate printing pathway design results in generating physiological-like branchings and channel volumes that approximate Murray's law in the geometrical ratio between parent and daughter vessels. After gel formation, a temperature decrease below the LCST produces interconnected microchannels with distinct inlet and outlet regions. Initial placement of the sacrificial scaffolds in the bioreactors in a pre-defined manner directly yields perfusable structures via leakage-free fluid connections in a reproducible one-step procedure. Using this approach, rapid formation of a tight and biologically functional endothelial layer, as assessed not only through fluorescent dye diffusion, but also by tumor necrosis factor alpha (TNF-α) stimulation, is obtained within three days. KW - hydrogels KW - microvasculature KW - melt electrowriting Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318532 VL - 34 IS - 28 ER - TY - JOUR A1 - Weigl, Franziska A1 - Blum, Carina A1 - Sancho, Ana A1 - Groll, Jürgen T1 - Correlative Analysis of Intra– Versus Extracellular Cell Detachment Events via the Alignment of Optical Imaging and Detachment Force Quantification JF - Advanced Materials Technologies N2 - In recent decades, hybrid characterization systems have become pillars in the study of cellular biomechanics. Especially, Atomic Force Microscopy (AFM) is combined with a variety of optical microscopy techniques to discover new aspects of cell adhesion. AFM, however, is limited to the early-stage of cell adhesion, so that the forces of mature cell contacts cannot be addressed. Even though the invention of Fluidic Force Microscopy (FluidFM) overcomes these limitations by combining the precise force-control of AFM with microfluidics, the correlative investigation of detachment forces arising from spread mammalian cells has been barely achieved. Here, a novel multifunctional device integrating Fluorescence Microscopy (FL) into FluidFM technology (FL-FluidFM) is introduced, enabling real-time optical tracking of entire cell detachment processes in parallel to the undisturbed acquisition of force-distance curves. This setup, thus, allows for entailing two pieces of information at once. As proof-of-principle experiment, this method is applied to fluorescently labeled rat embryonic fibroblast (REF52) cells, demonstrating a precise matching between identified force-jumps and visualized cellular unbinding steps. This study, thus, presents a novel characterization tool for the correlated evaluation of mature cell adhesion, which has great relevance, for instance, in the development of biomaterials or the fight against diseases such as cancer. KW - Fluorescence Microscopy KW - FluidFM technology KW - detachment force quantification Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318544 SN - 2365-709X VL - 7 IS - 11 ER - TY - JOUR A1 - Pien, Nele A1 - Bartolf–Kopp, Michael A1 - Parmentier, Laurens A1 - Delaey, Jasper A1 - de Vos, Lobke A1 - Mantovani, Diego A1 - van Vlierberghe, Sandra A1 - Dubruel, Peter A1 - Jungst, Tomasz T1 - Melt Electrowriting of a Photo–Crosslinkable Poly(ε–caprolactone)–Based Material into Tubular Constructs with Predefined Architecture and Tunable Mechanical Properties JF - Macromolecular Materials and Engineering N2 - Melt electrowriting (MEW) is an additive manufacturing process that produces highly defined constructs with elements in the micrometer range. A specific configuration of MEW enables printing tubular constructs to create small-diameter tubular structures. The small pool of processable materials poses a bottleneck for wider application in biomedicine. To alleviate this obstacle, an acrylate-endcapped urethane-based polymer (AUP), using a poly(ε-caprolactone) (PCL) (molar mass: 20 000 g mol\(^{−1}\)) (AUP PCL20k) as backbone material, is synthesized and utilized for MEW. Spectroscopic analysis confirms the successful modification of the PCL backbone with photo-crosslinkable acrylate endgroups. Printing experiments of AUP PCL20k reveal limited printability but the photo-crosslinking ability is preserved post-printing. To improve printability and to tune the mechanical properties of printed constructs, the AUP-material is blended with commercially available PCL (AUP PCL20k:PCL in ratios 80:20, 60:40, 50:50). Print fidelity improves for 60:40 and 50:50 blends. Blending enables modification of the constructs' mechanical properties to approximate the range of blood vessels for transplantation surgeries. The crosslinking-ability of the material allows pure AUP to be manipulated post-printing and illustrates significant differences in mechanical properties of 80:20 blends after crosslinking. An in vitro cell compatibility assay using human umbilical vein endothelial cells also demonstrates the material's non-cytotoxicity. KW - acrylate-endcapped urethane-based polymer (AUP) KW - tubular constructs KW - physicochemical characterization KW - photo-crosslinking KW - melt electrowriting (MEW) Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318524 SN - 1438-7492 VL - 307 IS - 7 ER - TY - JOUR A1 - Haag, Hannah A1 - Sonnleitner, David A1 - Lang, Gregor A1 - Dalton, Paul D. T1 - Melt electrowriting to produce microfiber fragments JF - Polymers for Advanced Technologies KW - melt electrowriting KW - medical-grade poly(ε-caprolactone) KW - fiber Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318465 SN - 1042-7147 VL - 33 IS - 6 SP - 1989 EP - 1992 ER - TY - JOUR A1 - Böhm, Christoph A1 - Tandon, Biranche A1 - Hrynevich, Andrei A1 - Teßmar, Jörg A1 - Dalton, Paul D. T1 - Processing of Poly(lactic–co–glycolic acid) Microfibers via Melt Electrowriting JF - Macromolecular Chemistry and Physics N2 - Polymers sensitive to thermal degradation include poly(lactic-co-glycolic acid) (PLGA), which is not yet processed via melt electrowriting (MEW). After an initial period of instability where mean fiber diameters increase from 20.56 to 27.37 µm in 3.5 h, processing stabilizes through to 24 h. The jet speed, determined using critical translation speed measurements, also reduces slightly in this 3.5 h period from 500 to 433 mm min\(^{−1}\) but generally remains constant. Acetyl triethyl citrate (ATEC) as an additive decreases the glass transition temperature of PLGA from 49 to 4 °C, and the printed ATEC/PLGA fibers exhibits elastomeric behavior upon handling. Fiber bundles tested in cyclic mechanical testing display increased elasticity with increasing ATEC concentration. The processing temperature of PLGA also reduces from 165 to 143 °C with increase in ATEC concentration. This initial window of unstable direct writing seen with neat PLGA can also be impacted through the addition of 10-wt% ATEC, producing fiber diameters of 14.13 ± 1.69 µm for the first 3.5 h of heating. The investigation shows that the initial changes to the PLGA direct-writing outcomes seen in the first 3.5 h are temporary and that longer times result in a more stable MEW process. KW - poly(lactide-co-glycolide) KW - 3D printing KW - additive manufacturing KW - electrohydrodynamics KW - melt electrospinning writing KW - plasticizers Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318444 VL - 223 IS - 5 ER - TY - JOUR A1 - Kade, Juliane C. A1 - Otto, Paul F. A1 - Luxenhofer, Robert A1 - Dalton, Paul D. T1 - Melt electrowriting of poly(vinylidene difluoride) using a heated collector JF - Polymers for Advanced Technologies N2 - Previous research on the melt electrowriting (MEW) of poly(vinylidene difluoride) (PVDF) resulted in electroactive fibers, however, printing more than five layers is challenging. Here, we investigate the influence of a heated collector to adjust the solidification rate of the PVDF jet so that it adheres sufficiently to each layer. A collector temperature of 110°C is required to improve fiber processing, resulting in a total of 20 fiber layers. For higher temperatures and higher layers, an interesting phenomenon occurred, where the intersection points of the fibers coalesced into periodic spheres of diameter 206 ± 52 μm (26G, 150°C collector temperature, 2000 mm/min, 10 layers in x- and y-direction).The heated collector is an important component of a MEW printer that allows polymers with a high melting point to be processable with increased layers. KW - additive manufacturing KW - polymer processing KW - melt electrowriting KW - electroactive Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318493 SN - 1042-7147 VL - 32 IS - 12 SP - 4951 EP - 4955 ER - TY - JOUR A1 - Brand, Jessica S. A1 - Forster, Leonard A1 - Böck, Thomas A1 - Stahlhut, Philipp A1 - Teßmar, Jörg A1 - Groll, Jürgen A1 - Albrecht, Krystyna T1 - Covalently Cross-Linked Pig Gastric Mucin Hydrogels Prepared by Radical-Based Chain-Growth and Thiol-ene Mechanisms JF - Macromolecular Bioscience N2 - Mucin, a high molecular mass hydrophilic glycoprotein, is the main component of mucus that coats every wet epithelium in animals. It is thus intrinsically biocompatible, and with its protein backbone and the o-glycosidic bound oligosaccharides, it contains a plethora of functional groups which can be used for further chemical modifications. Here, chain-growth and step-growth (thiol-ene) free-radical cross-linked hydrogels prepared from commercially available pig gastric mucin (PGM) are introduced and compared as cost-efficient and easily accessible alternative to the more broadly applied bovine submaxillary gland mucin. For this, PGM is functionalized with photoreactive acrylate groups or allyl ether moieties, respectively. Whereas homopolymerization of acrylate-functionalized polymers is performed, for thiol-ene cross-linking, the allyl-ether-functionalized PGM is cross-linked with thiol-functionalized hyaluronic acid. Morphology, mechanical properties, and cell compatibility of both kinds of PGM hydrogels are characterized and compared. Furthermore, the biocompatibility of these hydrogels can be evaluated in cell culture experiments. KW - click chemistry KW - photopolymerization KW - hydrogels KW - mucin KW - thiol-ene Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-318453 VL - 22 IS - 4 ER - TY - THES A1 - Dahinten, Anna T1 - Baghdadit - Biozemente in der Anwendung als endodontischer Funktionswerkstoff T1 - Baghdadite - biocements in the application as endodontic functional material N2 - In kürzlich erschienenen Studien hat sich die Zementformulierung Baghdadit (Ca3ZrSi2O9) durch Eigenschaften wie eine hydraulische Aktivität, Röntgenopazität und bioaktive Wirkung als potenzielles Material für die endodontische Anwendung qualifiziert. Ziel dieser Studie war es, Baghdadit als einphasigen Biozement und in Form verschiedener Materialzusammensetzungen auf vorteilhafte Eigenschaften im Hinblick auf die Anwendung als endodontischen Funktionswerkstoff zu untersuchen. Nach eigenständiger Herstellung des mechanisch aktivierten Zementpulvers Ca3ZrSi2O9, erfolgte die Charakterisierung der verschiedenen Zementformulierungen maBag, Bag100Bru und Bag50Bru hinsichtlich der Injizierbarkeit, des pH-Verlaufs während der Abbindung, der Druckfestigkeit und Phasenzusammensetzung mittels XRD. Daneben wurde Baghdadit zu je drei verschiedenen Gewichtsanteilen als Füllstoff in eine Methacrylat-basierte Matrix integriert und hinsichtlich der Fließfähigkeit entsprechend der Norm DIN EN ISO 6876:2012, des qualitativen Polymerisationsgrads und der Druckfestigkeit geprüft. Mit einer Auswahl der oben genannten Materialien erfolgte die Untersuchung der antibakteriellen Wirksamkeit, der Röntgensichtbarkeit orientierend an der Norm DIN EN ISO 13116:2014 und der Dichtigkeit im Wurzelkanal. N2 - In recent studies, the cement formulation Baghdadite (Ca3ZrSi2O9) has been qualified as a potential material for endodontic application by properties such as a hydraulic activity, radiopacity and bioactive effect. The aim of this study was to investigate baghdadite as a single-phase biocement and in the form of different material compositions for advantageous properties with regard to its application as an endodontic filling material. After the production of the mechanically activated cement powder Ca3ZrSi2O9, the different cement formulations maBag, Bag100Bru and Bag50Bru were characterized with regard to injectability, pH curve during setting, compressive strength and phase composition carried out by XRD. In addition, baghdadite was integrated as filler into a methacrylate-based matrix in three different proportions by weight. These experimental sealers were tested with regard to flowability according to DIN EN ISO 6876:2012, the qualitative degree of polymerization and the compressive strength. With a selection of the above-mentioned materials the investigation of the antibacterial efficacy, the radiopacity based on the standard DIN EN ISO 13116:2014 and the sealing ability in bovine root canals were carried out. KW - Endodontie KW - Funktionswerkstoff KW - Baghdadit KW - Biozement KW - Zahnmedizin Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-319892 ER -