TY - JOUR A1 - Pollmann, Stephan A1 - Toussaint, André A1 - Flentje, Michael A1 - Wegener, Sonja A1 - Lewitzki, Victor T1 - Dosimetric evaluation of commercially available flat vs. self-produced 3D-conformal silicone boluses for the head and neck region JF - Frontiers in Oncology N2 - Background Boluses are routinely used in radiotherapy to modify surface doses. Nevertheless, considerable dose discrepancies may occur in some cases due to fit inaccuracy of commercially available standard flat boluses. Moreover, due to the simple geometric design of conventional boluses, also surrounding healthy skin areas may be unintentionally covered, resulting in the unwanted dose buildup. With the fused deposition modeling (FDM) technique, there is a simple and possibly cost-effective way to solve these problems in routine clinical practice. This paper presents a procedure of self-manufacturing bespoke patient-specific silicone boluses and the evaluation of buildup and fit accuracy in comparison to standard rectangular commercially available silicone boluses. Methods 3D-conformal silicone boluses were custom-built to cover the surgical scar region of 25 patients who received adjuvant radiotherapy of head and neck cancer at the University Hospital Würzburg. During a standard CT-based planning procedure, a 5-mm-thick 3D bolus contour was generated to cover the radiopaque marked surgical scar with an additional safety margin. From these digital contours, molds were 3D printed and poured with silicone. Dose measurements for both types of boluses were performed with radiochromic films (EBT3) at three points per patient—at least one aimed to be in the high-dose area (scar) and one in the lower-dose area (spared healthy skin). Surface–bolus distance, which ideally should not be present, was determined from cone-beam CT performed for positioning control. The dosimetric influence of surface–bolus distance was also determined on slab phantom for different field sizes. The trial was performed with hardware that may be routinely available in every radiotherapy department, with the exception of the 3D printer. The required number of patients was determined based on the results of preparatory measurements with the help of the statistical consultancy of the University of Würzburg. The number of measuring points represents the total number of patients. Results In the high-dose area of the scar, there was a significantly better intended dose buildup of 2.45% (95%CI 0.0014–0.0477, p = 0.038, N = 30) in favor of a 3D-conformal bolus. Median distances between the body surface and bolus differed significantly between 3D-conformal and commercially available boluses (3.5 vs. 7.9 mm, p = 0.001). The surface dose at the slab phantom did not differ between commercially available and 3D-conformal boluses. Increasing the surface–bolus distance from 5 to 10 mm decreased the surface dose by approximately 2% and 11% in the 6 × 6- and 3 × 3-cm2 fields, respectively. In comparison to the commercially available bolus, an unintended dose buildup in the healthy skin areas was reduced by 25.9% (95%CI 19.5–32.3, p < 0.01, N = 37) using the 3D-conformal bolus limited to the region surrounding the surgical scar. Conclusions Using 3D-conformal boluses allows a comparison to the commercially available boluses’ dose buildup in the covered areas. Smaller field size is prone to a larger surface–bolus distance effect. Higher conformity of 3D-conformal boluses reduces this effect. This may be especially relevant for volumetric modulated arc therapy (VMAT) and intensity-modulated radiotherapy (IMRT) techniques with a huge number of smaller fields. High conformity of 3D-conformal boluses reduces an unintended dose buildup in healthy skin. The limiting factor in the conformity of 3D-conformal boluses in our setting was the immobilization mask, which was produced primarily for the 3D boluses. The mask itself limited tight contact of subsequently produced 3D-conformal boluses to the mask-covered body areas. In this respect, bolus adjustment before mask fabrication will be done in the future setting. KW - flat silicone bolus KW - individual silicone bolus KW - 3D conformal silicone bolus KW - 3D printer KW - head and neck cancer KW - fused deposition modeling (FDM) KW - surface dose measurement KW - volumetric modulated arc therapy (VMAT) Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-283156 SN - 2234-943X VL - 12 ER - TY - THES A1 - Pollmann, Stephan T1 - Herstellung und dosimetrische Evaluation flexibler, 3D-konformaler Boli für die adjuvante volumenmodulierte Radiotherapie bei Kopf-Hals-Tumoren T1 - Production and dosimetric evaluation of flexible, 3D-conformal boluses for adjuvant volume-modulated radiotherapy in head and neck tumours N2 - In der vorliegenden Arbeit wurde ein standardisiertes Verfahren zur Herstellung individueller Boli mithilfe von FDM und Silikon-Guss vorgestellt. Die Technik schien den Vorteil einer relativ preisgünstigen Bolus-Produktion vor Ort bei verhältnismäßig geringen Ansprüchen an infrastrukturelle Voraussetzungen in der Klinik zu bieten, auch wenn eine Untersuchung ökonomischer Aspekte nicht Ziel der Arbeit war. Gleichzeitig konnten flexible und für den Patienten möglicherweise komfortablere Boli erzeugt werden, die konformaler bzw. lückenloser auflagen als die konventionellen Modelle (Superflabs), eine geringfügige Dosiserhöhung im oberflächlichen Zielvolumen bewirkten und zudem eine deutliche Hautschonung ermöglichten. Über den gesamten Anwendungszeitraum hielten die Boli den mechanischen Belastungen stand, die mit der Behandlung der Patienten einhergingen. Im Rahmen vorausgegangener Untersuchungen an einem Plattenphantom konnte die Äquivalenz der Materialien in Bezug auf den Dosisaufbau erwiesen werden, sodass die Zusammensetzung des von uns verwendeten Materials als sowohl mechanisch wie physikalisch geeignet angesehen werden konnte. Der Einfluss unterschiedlich großer Bolus-Hohlräume auf eine oberflächliche Dosisreduktion wurde am Plattenphantom ebenfalls abgeschätzt. Am RANDO-Phantom konnte ein geeignetes Messverfahren identifiziert werden. Die Ergebnisse unserer Untersuchungen an 3D-konformalen Boli zeigten sich als mit der aktuellen Studienlage weitgehend kongruent. Eine weitere Optimierung der vorgestellten Technik könnte über die Verwendung von 3D-Scans der Kopf-Hals-Konturen erreicht werden, da dies eine Integration von Bolus- und Maskenanbringung ermöglicht. Hohlräume unter einer Lagerungsmaske hätten damit weniger Einfluss auf den Bolus-Haut-Abstand. Ebenso erscheint die klinische Evaluation der Rezidivhäufigkeit bzw. der Hautschonung als sinnvoll. Es könnte beispielsweise die Verhinderung akuter und chronischer Strahlen-wirkungen an der sensiblen Kopf-Hals-Region quantifiziert werden. Die vorgestellte 3D-Druck- und Gusstechnik zur Herstellung flexibler und 3D-konformaler Boli erscheint bei der Optimierung strahlentherapeutischer Behandlungsmöglichkeiten vielversprechend. N2 - In the present study, a standardised procedure for the production of individual boluses using FDM and silicone casting was presented. The technique seemed to offer the advantage of relatively inexpensive bolus production on site with relatively low demands on infrastructural requirements in the clinic, even though an investigation of economic aspects was not the aim of the work. At the same time, it was possible to produce flexible boluses that were possibly more comfortable for the patient, which were more conformal or had fewer gaps than the conventional models (superflabs), caused a slight increase in the dose in the superficial target volume and also enabled significant skin protection. Over the entire application period, the boluses withstood the mechanical stresses associated with the treatment of the patients. In previous studies on a plate phantom, the equivalence of the materials in terms of dose build-up was proven, so that the composition of the material we used could be considered suitable both mechanically and physically. The influence of bolus cavities of different sizes on a superficial dose reduction was also estimated on the plate phantom. A suitable measurement procedure could be identified on the RANDO phantom. The results of our investigations on 3D-compliant boluses were found to be largely congruent with the current state of studies. Further optimisation of the presented technique could be achieved by using 3D scans of the head and neck contours, as this allows integration of bolus and mask attachment. Cavities under a positioning mask would thus have less influence on the bolus-skin distance. Similarly, clinical evaluation of recurrence frequency or skin sparing appears to be useful. For example, the prevention of acute and chronic radiation therapy-related side effects on the sensitive head and neck region could be quantified. The 3D printing and casting technique presented for the production of flexible and 3D-conformal boluses appears promising in the optimisation of radiotherapeutic treatment options. KW - individueller Bolus KW - 3D-konformaler Bolus KW - volumetric modulated arc therapy KW - fused deposition modeling KW - Kopf-Hals-Tumore Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-303681 ER -