TY - THES A1 - Wienen, Frank T1 - Kapillarelektrophoretische Trennung und Quantifizierung von Aminoglykosiden und Clotrimazol T1 - Separation and quantification of aminoglycosides and clotrimazole by means of capillary electrophoresis N2 - Im Rahmen dieser Arbeit wurden kapillarelektrophoretische Methoden entwickelt, mit denen es möglich ist, Gentamicinsulfat in Haupt- und Nebenkomponenten zu trennen. Ausgelöst wurden die Untersuchungen im Jahr 2000, da in den USA über 60 Patienten durch Gentamicin starben. Es wurde vermutet, dass dies auf Verunreinigungen in gewissen Chargen zurückzuführen ist. Gentamicin wird fermentativ aus Micromonospora purpurea gewonnen. Durch leichte Abweichungen im Herstellungsprozess können Produkte entstehen, die mit den bisher angewendeten Analysenmethoden nicht nachzuweisen sind. In der momentanen Arzneibuch-Monographie von Gentamicinsulfat wird zur Prüfung der verwandten Substanzen eine HPLC-Methode beschrieben, die Gentamicin ohne Derivatisierung mit einem gepulsten amperometrischen Detektor detektiert. Vorteil dieser Methode ist, dass Gentamicin nicht derivatisiert werden muss. Der große Nachteil dieser Methode ist aber, dass die einzelnen Peaks sehr lange Migrationszeiten haben (bis über 10 Minuten) und somit Verunreinigungen überdeckt werden können. Außerdem sind viele Bestandteile nicht von den Hauptkomponenten abgetrennt. Weiterhin ist diese Methode nicht sehr robust, da der Detektor sehr empfindlich ist. Eigene HPLC-Messungen an mehreren Gentamicin-Chargen zeigten die Probleme auf. Da Gentamicin kein chromophores System hat, kann es nicht mit einem UV/VIS-Detektor detektiert werden. Um dies dennoch zu ermöglichen, kann Gentamicin mit verschiedenen Reagenzien derivatisiert werden. In der vorliegenden Arbeit wurden alle Aminoglykoside mit ortho-Phthaldialdehyd und 2-Mercaptoessigsäure derivatisiert. Somit war eine Detektion bei 330 nm bzw. 340 nm möglich. Zur Trennung von Gentamicinsulfat wurde eine spezielle kapillarelektrophoretische Methode entwickelt. Die mizellare elektrokinetische Chromatographie (MEKC) ist nach Derivatisierung in der Lage, nahezu alle in der Monographie beschriebenen aber auch einige nicht aufgeführte Verunreinigungen zu trennen. Die Trennung erfolgt in einer Kieselgelkapillare mit einer Gesamtlänge von 33.0 cm, einer effektiven Länge von 24.5 cm und einem Innendurchmesser von 50 µm. Als Hintergrundelektrolyt wird ein Natriumtetraborat-Puffer verwendet (100 mM, pH 10.0), zu dem Desoxycholsäure-Natrium als mizellbildendes Reagenz in einer Konzentration von 20 mM und weiterhin beta-Cyclodextrin in einer Konzentration von 15 mM zugegeben wird. Die Proben werden hydrodynamisch bei 5000 Pa innerhalb 5 Sekunden auf der Anodenseite injiziert. Die Trennung erfolgt bei einer Kapillartemperatur von 25 °C und einer Trennspannung von +12 kV. Pikrinsäure wird als Interner Standard benutzt. Die Detektion erfolgt UV-spektroskopisch bei 340 nm. Die Hauptpeaks konnten durch „spiken“ mit den Einzelkomponenten, die u.a. säulenchromatographisch gewonnen wurden, identifiziert werden. Die vier Hauptkomponenten Gentamicin-C1, C1a, C2 und C2a sind basisliniengetrennt ebenso wie Gentamicin-C2b, die Verunreinigungen Garamin, Desoxystreptamin und Sisomicin. Bei den Untersuchungen von über 40 Gentamicin-Chargen verschiedener Hersteller und Händler fielen sowohl deutliche Unterschiede bezüglich der einzelnen Gehalte der Hauptkomponenten auf, als auch verschiedene Grade der Verunreinigungen. Anhand der Menge der Verunreinigungen konnten die Chargen in verschiedene Gruppen eingeteilt werden. Die Verunreinigung Sisomicin kann als Leitsubstanz der Verunreinigungen bezeichnet werden, da bei allen stärker verunreinigten Chargen Sisomicin in beträchtlichen Mengen vorhanden ist. Unter den untersuchten Proben befanden sich auch die Proben, die in den USA die eingangs erwähnten Todesfälle verursacht haben. Diese Proben konnten der Gruppe der stärker verunreinigten Gentamicin-Chargen eindeutig zugewiesen werden. Die Richtigkeit aller Messungen wurde durch 1H-NMR-Messungen bestätigt. Die Anwendbarkeit der entwickelten MEKC-Methode wurde auch an weiteren Aminoglykosiden untersucht. Die Methode ist ohne Änderung auf Sisomicin übertragbar. Der Sisomicin-Peak ist deutlich abgetrennt vom OPA-Reagenzpeak. Selbst kleine Verunreinigungen der CRS-Substanz können mit dieser Methode erkannt werden. Netilmicin und Amikacin können nicht ohne Änderungen mit der Methode vermessen werden, da sie unter diesen Bedingungen mit dem OPA-Peak komigrieren. Eine Anhebung der Trennspannung von +12 kV auf +14 kV lassen die Peaks hervortreten. Eine Unterscheidung der beiden Substanzen ist im Elektropherogramm nicht möglich, allerdings können sie durch 1H-NMR-spektroskopische Messungen identifiziert und unterschieden werden. Netilmicin wurde in vielen Gentamicin-Proben nachgewiesen. Bei Kanamycin liegen mit dieser Methode im Elektropherogramm sehr viele kleine Peaks sehr nahe beieinander. Durch Absenkung der Kapillartemperatur auf 20 °C können diese Peaks etwas besser getrennt werden... N2 - The aim of this study was to separate gentamicin sulfate into its major and minor components by means of capillary electrophoresis. In May 2000 the death of 17 people and 60 people, respectively, was reported, following the administration of the commonly used broad spectrum antibiotic gentamicin sulfate. In addition hundreds of patients suffering from severe side effects were reported. Since this could not be explained by the pharmacological and toxicological properties of gentamicin, it was assumed that the side effects were related to impurities. Due to the fact that gentamicin is a fermentation product of Micromonospora purpurea, minor variations in the fermentation procedure may cause products, that cannot be detected by the analytical methods applied thus far. The current European Pharmacopoeia limits for related substance of gentamicin by means of an HPLC-method in combination with a pulsed amperometric detector. The advantage of this method is the fact, that it is not necessary to derivatize gentamicin. However, a major disadvantage of the method is the broadness of the main peaks (>10 minutes/peak). Hence, minor products could be covered by the main peaks. Furthermore, various peaks are not baseline separated and the method is not very robust owing to the highly sensitive detector. Due to the lack of a chromophore, gentamicin needs to be derivatized to allow detection by means of an UV-detector. In this study all aminoglycosides were labeled with orthophthaldialdehyde (OPA) in combination with 2-mercaptoacetic acid, which enabled detection at a wavelength of 340 nm. To separate gentamicin as OPA derivative, a method based on micellar electrokinetic chromatography (MEKC) was developed. This technique makes it possible to separate most of the impurities specified in the gentamicin monograph (garamine, deoxystreptamine, and sisomicin) and some additional, not further specified impurities such as paromamine and unknown products. The separation is carried out in a fused-silica capillary with a total length of 33.0 cm, an effective length of 24.5 cm and an inner diameter of 50 µm. Using sodium tetraborate buffer (100 mM, pH 10.0) as background electrolyte (BGE), deoxycholic acid sodium in a concentration of 20 mM as micelle forming agent and beta-cyclodextrin in a concentration of 15 mM are added. The samples are loaded hydrodynamically at 5000 Pa for 5 seconds on the anode side of the capillary and the separation is carried out at +12 kV and 25 °C. Picric acid is used as an internal standard and UV-detection is performed at 340 nm. Spiking experiments were performed using reference substances, obtained by column chromatography and commercially purchased reference substances for the impurities. The four major components gentamicin C1, C1a, C2, and C2a as well as the minor component C2b and the impurities garamine, deoxystreptamine, and sisomicin are baseline separated. Over 40 gentamicin batches of different pharmaceutical companies and producers were analyzed with respect to the content of the major components as well as the amount of the impurities. Varying levels of the major compounds as well as the impurities were identified, which allowed the grouping of the samples. All samples exhibiting a high amount of impurities were found to a high sisomicin concentration. Hence, sisomicin can be referred to as an impurity indicator. Some of the batches under scrutiny were responsible for the deaths found in the US. All these samples could be unambiguously assigned to the group which is characterized by a high number and a relatively high quantity of most unspecified impurities. All CE-measurements were verified by 1H NMR measurements. To investigate the applicability of the developed MEKC method, other aminoglycosides were also investigated. For sisomicin the standard method can be used without modification, since the sisomicin peak is separated from the OPA reagent peak and even small amounts of impurities of the CRS-substance can be detected with this method. For netilmicin and amikacin the developed method has to be modified. Under standard conditions the peaks of both substances co-migrates with the OPA reagent peak. Raising the voltage from +12 kV to +14 kV both peaks are separated. All Gentamicin samples were measured again using these new conditions. Netilmicin was often found in gentamicin samples. However, for these new conditions the migration time of netilmicin and amikacin are similar. Hence, they cannot be differentiated from each other in the same sample. Nevertheless, this differentiation can be carried out with 1H NMR measurements. Kanamycin samples show many peaks in a small zone of the electropherogram using the MEKC standard method. A slightly better separation can be obtained by using a lower temperature of the capillary of 20 °C instead of 25 °C... KW - Aminoglykoside KW - Micellare elektrokinetische Kapillarchromatographie KW - Gentamicin KW - Verunreinigung KW - Clotrimazol KW - Quantitative Analyse KW - Gentamicin KW - MEKC KW - Cyclodextrin KW - ortho-Phthaldialdehyd KW - Derivatisierung KW - gentamicin KW - MEKC KW - cyclodextrin KW - ortho-phthaldialdehyd KW - derivatisation Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-7796 ER - TY - THES A1 - Wahl, Oliver T1 - Impurity Profiling of Challenging Active Pharmaceutical Ingredients without Chromophore T1 - Erstellen von Verunreinigungsprofilen von anspruchsvollen Wirkstoffen ohne Chromophor N2 - The impurity profiling of pharmaceutical ingredients can oppose many challenges. The best part of active pharmaceutical ingredients (APIs) and the related substances are detectable by UV detection, a very common detection principle. However, if an API lacks a suitable chromophore other means of detection are necessary. The corona charged aerosol detector (CAD) is a detector capable of detecting substances independent of their chemical structure. This “universal” detector has only one limitation: The analyte has to have a sufficiently low vapor pressure. Another important challenge that comes often together with the lack of a chromophore concerns the separation. These substances (e.g. most amino acids and derivatives) often contain structures that make them difficult to retain on conventional reversed phase columns. Possible solutions to overcome these challenges, like the application of the CAD and the benefit of so-called mixed-mode stationary phases in impurity profiling for pharmacopoeial purposes were explored in this work. The related substances analyzed in this thesis comprise amino acids, inorganic ions, bisphosphonic acids, basic and acidic derivatives of amino acids (esters and amides). The successful development and validation of mixed-mode liquid chromatography methods with CAD detection for carbocisteine and ibandronate sodium might help to increase the acceptance of this versatile detector in the pharmaceutical industry and in official authorities dealing with the determination of related substances. The combination of UV and CAD detection proved very useful during the analysis of Bicisate. Most of the related substances and some unidentified impurities were detectable by CAD whereas a synthesis by-product, a semi-volatile ester, was only detectable in the UV trace. The simple combination covers all relevant impurities in a single analysis. Two truly orthogonal methods regarding separation and detection for the enantiomeric purity of magnesium-L-aspartate helped to find the reason for elevated D aspartic acid content in the drug substance. A very quick and sensitive indirect separation using the OPA derivatization with NAC was developed as a powerful screening tool, whereas the direct separation of D- and L-CBQCA-Asp derivatives confirmed the results. Both methods were optimized in order to do without substances mentioned on the REACH list, like sodium tetraborate which is very frequently applied in standard derivatization protocols and CE separations. The importance of orthogonal detection principles in the determination of related substances of amino acids was discussed in a review article dealing with the revision of amino acid monographs in the Ph. Eur.. N2 - Die Reinheitsprüfung pharmazeutischer Wirkstoffe kann den Analytiker vor verschiedene Hürden stellen. So gilt für den größten Teil pharmazeutischer Wirkstoffe und deren verwandte Substanzen, dass sie mit Hilfe des weit verbreiteten UV-Detektors nachweisbar sind. Verfügt ein Wirkstoff hingegen nicht über ein geeignetes Chromophor, so benötigt man andere Möglichkeiten der Detektion. Der corona charged aerosol detector (CAD) ist in der Lage Substanzen unabhängig von ihrer chemischen Struktur zu detektieren, vorausgesetzt, sie sind schwerflüchtig. Eine weitere Herausforderung, die häufig mit dem Fehlen eines Chromophors einhergeht betrifft die Trennung. Verbindungen dieser Art (z.B. die meisten Aminosäuren und deren Derivate) enthalten häufig Strukturen, die eine Trennung auf konventionellen Umkehrphasen erschweren. Mögliche Ansätze um die genannten Herausforderungen zu meistern, wie zum Beispiel die Verwendung des CAD und sogenannter mixed-mode Phasen in der pharmazeutischen Reinheitsanalytik wurden erarbeitet und an konkreten Anwendungen erprobt. Die in dieser Arbeit bestimmten verwandten Substanzen sind vor allem Aminosäuren, anorganische Ionen, Bisphosphonate sowie basische und saure Derivate von Aminosäuren (Ester und Amide). Die erfolgreiche Entwicklung und Validierung von mixed-mode flüssig-chromatographischer Methoden kombiniert mit CAD für Carbocistein und Ibandronat Natrium könnte dabei helfen die Akzeptanz in der Pharmazeutischen Industrie und bei den für Reinheitsprüfungen zuständigen Behörden für diesen vielseitigen Detektor zu verbessern. Die Kombination von UV-Detektion und CAD erwies sich bei der Analyse von Bicisate als sehr nützlich. Die meisten verwandten Substanzen und einige unbekannte Verunreinigungen konnten mittels CAD detektiert werden, während ein Nebenprodukt der Synthese, ein halb-flüchtiger Ester, nur mit Hilfe des UV Detektors sichtbar war. Die Kombination zweier Detektionstechniken ermöglichte die Bestimmung aller relevanten Verunreinigungen in einer einzigen Analyse. Die Bestimmung der optischen Reinheit von Magnesium-L-Aspartat gelang mittels zweier orthogonaler Methoden und der Grund für das Auftreten von erhöhten Konzentrationen an D-Aspartat wurde gefunden. Eine schnelle indirekte Bestimmung der OPA/NAC-Derivate eignete sich als Screening-tool, während die direkte Trennung der enantiomeren CBQCA-Derivate die Ergebnisse bestätigte. Beide Methoden wurden im Hinblick darauf optimiert, dass sie ohne Substanzen wie Natriumtetraborat, eine Substanz auf der REACH Liste für besonders besorgniserregende Substanzen, sowie gebräuchlicher Puffer bei Derivatisierungsreaktionen und CZE Trennungen, auskamen. Die Bedeutung von orthogonalen Detektionstechniken bei der Bestimmung der verwandten Substanzen von Aminosäuren wurde in einem Übersichtsartikel, der in Zusammenhang mit der Revision von Aminosäuren Monographien des Europäischen Arzneibuches steht, diskutiert. KW - Chromatographie KW - Verunreinigung KW - Impurity Profiling KW - Amino acids KW - Corona charged aerosol detector KW - Aminosäuren Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-137205 ER - TY - THES A1 - Urlaub, Jonas T1 - Development of analytical methods for the quality assessment of mineral oil based excipients and mechanochemically stressed active pharmaceutical ingredients T1 - Entwicklung analytischer Methoden für die Qualitätsbeurteilung mineralölbasierter Hilfsstoffe und mechanochemisch gestresster Arzneistoffe N2 - For the quality assurance of substances for pharmaceutical use, a variety of analytical techniques are available to address specific analytical problems. In this field of application, liquid chromatography (LC) stands out as the gold standard in the pharmaceutical industry. Various detectors can be employed, which are e.g. based on UV/Vis spectroscopy for the examination of molecules with a chromophore, or mass spectrometry (MS) for structural elucidation of analytes. For the separation of enantiomers, the use of capillary electrophoresis (CE) may be more favorable due to the high separation efficiency and easy-to-use and comparatively inexpensive chiral selectors, in contrast to chiral columns for LC, which are usually very expensive and limited to a restricted number of analytes. For structure elucidation in impurity profiling, one- and multidimensional 1H NMR spectroscopy is a valuable tool as long as the analyte molecule has got nuclei that can be detected, which applies for the magnitude of organic pharmaceutical substances. For the evaluation of the amount of mineral oil aromatic hydrocarbons (MOAH) in various paraffin samples from different suppliers, a straightforward method based on 1H NMR spectroscopy was elaborated. The MOAH/MOSH ratio was used to indicate the amount of MOAH of paraffins and to evaluate the extent of refining. In addition, a representative paraffin sample was measured without sample solvent at high temperatures (about 340 K) to avoid the interfering residual solvent signals in the spectral regions of interest. The results of both methods were in good accordance. Moreover, the 1H NMR results were complemented with the UV measurements from the purity testing of paraffins according to the DAB 8. Correlations of the NMR and UV spectroscopic data indicated a linear relationship of both methods for the determination of MOAH in paraffins. Finally, the 1H NMR data was evaluated by principal component analysis (PCA) to explore differences within the paraffin samples and the spectral regions in the 1H NMR spectrum which are responsible for the formation of groups. It could be found that most variation is due to the MOSH of the paraffins. The PCA model was capable of differentiating between soft, liquid and solid paraffins on the one hand and between natural and synthetic liquid paraffins on the other hand. The impurity profiling of L-ascorbic acid 2-phosphate magnesium (A2PMg) was performed by means of one- and two-dimensional NMR spectroscopy. Several ethylated impurities could be detected, which were likely to be formed during synthesis of A2PMg. The structures of two of the ethylated impurities were identified as ascorbic acid 2-phosphate ethyl ester and ethanol, (residual solvent from synthesis). NMR spectroscopic studies of the fractions obtained from preparative HPLC of A2PMg revealed two additional impurities, which were identified as phosphorylated derivatives of ascorbic acid, ascorbic acid 3,5-phosphate and ascorbic acid 5-phosphate. Solid state mechanochemistry as an alternative approach for stress testing was applied on the drug substances S-Ibuprofen (Ibu) and Clopidogrel (CLP) using a ball mill, in order to study their degradation profile: First, the isomerization of S-Ibu was investigated, which was stressed in the solid state applying several milling frequencies and durations under basic, acidic and neutral conditions. For the separation of Ibu enantiomers, a chiral CE method was developed and validated according to ICH Q2(R1). It was found that S-Ibu is overall very stable to isomerization; it shows minor conversion into the R-enantiomer under basic environment applying long milling times and high frequencies. Last, the degradation profile of clopidogrel hydrogen sulfate (CLP) was investigated, which was stressed in the solid state under various oxidative conditions. An already existing HPLC-UV method was adjusted to sufficiently separate the degradation products, which were characterized by means of UV and MS/(MS) detection. Most of the degradation products identified were already reported to result from conventional CLP stress tests. The degradation profile of CLP was mainly influenced by the material of the milling jar and the type of catalyst used. N2 - Für die Qualitätssicherung von Arznei- und Hilfsstoffen steht eine Vielzahl von analytischen Techniken für spezifische analytische Fragestellungen zur Verfügung. In der pharmazeutischen Industrie hat sich dabei die Flüssigkeitschromatographie als Goldstandard etabliert. Es können verschiedene Detektoren eingesetzt werden, die z. B. auf UV/Vis-Spektroskopie zur Untersuchung von Molekülen mit einem Chromophor oder auf Massenspektrometrie zur Strukturaufklärung von Analyten basieren. Für die Trennung von Enantiomeren kann die Verwendung von Kapillarelektrophorese aufgrund der hohen Trenneffizienz und der einfach zu handhabenden und vergleichsweise preiswerten chiralen Selektoren gegenüber chiralen Säulen in der Flüssigchromatographie bevorzugt sein, die in der Regel sehr teuer und auf eine begrenzte Anzahl von Analyten beschränkt sind. Für die Strukturaufklärung im Rahmen der Erstellung von Verunreinigungsprofilen ist die ein- und mehrdimensionale 1H-NMR-Spektroskopie eine sehr wertvolle Methode, solange das Analytmolekül Kerne besitzt, die der NMR-Spektroskopie zugänglich sind, was für den Großteil der organischen Arznei- und Hilfsstoffe zutrifft. Um die Menge an „mineral oil aromatic hydrocarbons (MOAH)“ in verschiedenen Paraffinproben von unterschiedlichen Herstellern zu bestimmen, wurde eine einfache 1H-NMR-Spektroskopie-Methode erarbeitet. Das Verhältnis von MOAH zu „mineral oil saturated hydrocarbons (MOSH)“ wurde dazu verwendet, um die Menge der MOAH in Paraffinen zu bestimmen und ihren Raffinationsgrad zu beurteilen. Zusätzlich wurde eine repräsentative Paraffinprobe ohne Probenlösungsmittel bei hohen Temperaturen (ca. 340 K) vermessen, um die interferierenden Restlösemittel Signale in den relevanten Spektralbereichen zu vermeiden. Die Ergebnisse beider Methoden stimmten gut überein. Weiterhin wurden die 1H-NMR-Ergebnisse durch die UV-Messungen aus der Reinheitsprüfung von Paraffinen gemäß DAB 8 ergänzt. Korrelationen der NMR- und UV-spektroskopischen Daten wiesen auf eine lineare Beziehung beider Methoden für die Bestimmung der MOAH in Paraffinen hin. Schließlich wurden die 1H-NMR-spektroskopischen Daten mittels Hauptkomponentenanalyse ausgewertet, um Unterschiede innerhalb der Paraffinproben und die für die Gruppenbildung verantwortlichen Spektralbereiche im 1H-NMR-Spektrum zu ermitteln. Es konnte festgestellt werden, dass der Hauptanteil der Varianz auf die MOSH zurückzuführen ist. Das PCA-Modell war dazu in der Lage, zwischen weichen, flüssigen und festen Paraffinen einerseits und zwischen natürlichen und synthetischen flüssigen Paraffinen andererseits zu unterscheiden. Das Verunreinigungsprofil von L-Ascorbinsäure-2-phosphat-Magnesium (A2PMg) wurde mittels ein- und zweidimensionaler NMR-Spektroskopie untersucht. Es konnten mehrere ethylierte Verunreinigungen nachgewiesen werden, die vermutlich während des Syntheseprozesses von A2PMg gebildet wurden. Die Strukturen von zwei der ethylierten Verunreinigungen wurden als Ascorbinsäure-2-phosphat ethylester und Ethanol (Restlösungsmittel aus der Synthese) identifiziert. NMR spektroskopische Untersuchungen der aus der präparativen HPLC von A2PMg erhaltenen Fraktionen ergab zwei weitere Verunreinigungen, die als phosphorylierte Derivate von Ascorbinsäure, Ascorbinsäure-3,5-phosphat und Ascorbinsäure-5-phosphat, identifiziert wurden. Die Festkörper-Mechanochemie als alternativer Ansatz für Stresstests wurde auf die Arzneistoffe S-Ibuprofen und Clopidogrel unter Einsatz einer Kugelmühle angewandt, um deren Abbauprofil zu analysieren: Zunächst wurde die Isomerisierung von S-Ibuprofen (Ibu) untersucht, das im festen Zustand unter Anwendung verschiedener Mahlfrequenzen und -dauern unter basischen, sauren und neutralen Bedingungen gestresst wurde. Für die Trennung der Ibu-Enantiomere wurde eine chirale Kapillarelektrophorese-Methode entwickelt und gemäß ICH Q2(R1) Leitlinie validiert. Es wurde festgestellt, dass S-Ibu insgesamt sehr stabil gegenüber Isomerisierung ist, jedoch unter basischen Bedingungen und hohen Mahldauern und -frequenzen eine geringe Umwandlung in das R-Enantiomer zeigt. Zuletzt wurde das Abbauprofil von Clopidogrelhydrogensulfat (CLP) untersucht, das im festen Zustand unter oxidativen Bedingungen gestresst wurde. Eine bereits bestehende HPLC-UV Methode wurde optimiert, um die Abbauprodukte ausreichend zu trennen und anschließend mittels UV- und MS/(MS)-Detektion zu charakterisieren. Die meisten der identifizierten Abbauprodukte waren bereits aus konventionellen CLP-Stresstests bekannt. Das Abbauprofil von CLP wurde hauptsächlich durch das Material der Kugelmühle und den Typ des verwendeten Katalysators beeinflusst. KW - HPLC KW - Kapillarelektrophorese KW - NMR-Spektroskopie KW - Paraffin KW - Verunreinigung KW - NMR spectroscopy KW - capillary electrophoresis KW - liquid chromatography KW - paraffins KW - mechanochemical degradation KW - impurities Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-243465 ER - TY - THES A1 - Novatchev, Nikolai T1 - Untersuchung des Verunreinigungsprofils von Aminosäuren aus fermentativer Herstellung mittels Kapillarelektrophorese T1 - Evaluation of the impurity profile of amino acids of biotechnological origin by means of capillary electrophoresis N2 - Gegenstand der vorliegenden Arbeit war die Untersuchungen von Verunreinigungsprofilen von Aminosäuren aus biotechnologischer Herstellung. Dazu sollten die Aminosäuren Arg, His, Ile, Lys, Phe, Pro, Ser und Trp von verschiedenen Herstellern und aus unterschiedlichen Batches genauer unter die Lupe genommen werden. Mit der im Europäischen Arzneibuch beschriebenen dünnschichtchromatographischen Methode (DC-Methode) für „mit Ninhydrin nachweisbare Substanzen“ können ausschließlich Fremdaminosäuren nachgewiesen werden und dies nur, wenn der jeweilige Gehalt relativ hoch ist. Andere Stoffgruppen, die aus der biotechnologischen Herstellung stammen, werden aufgrund der Trennbedingungen sowie der Detektionsart der DC-Methode nicht erfasst. Deshalb mussten neue Methoden entwickelt werden. Laut Vorschriften der International Conference of Harmonisation (ICH) müssen unbekannte Verunreinigungen in Wirkstoffen für orale Therapeutika auf 0,1 % w/w begrenzt werden können. In die Untersuchungen wurden neben den Fremdaminosäuren auch Peptide, Aminozucker und Nucleinsäuren als potentielle Verunreinigungen, die aus der Herstellung bzw. aus dem Reinigungsprozess kommen, einbezogen. Diese zusätzlichen Stoffgruppen können aus den „Nebenaktivitäten“ der Mikroorganismen entstehen. Aminosäuren, Peptide und Aminozucker wurden versucht, kapillarelektrophoretisch zu quantifizieren. Für die Bestimmung von Nucleinsäuren wurde zusätzlich die UV-Spektroskopie eingesetzt. N2 - Aim of the present work was to investigate the impurity profiles of amino acids of biotechnological origin. Eight amino acids were included: Arg, His, Ile, Lys, Phe, Pro, Ser and Trp. The amino acid samples originating from different producers and different batches had to be studied in deeper detail. The thin-layer chromatographic method (TLC-method) of “ninhydrin-positive substances”, as described in the European Pharmacopoeia, is able to detect primarily other amino acids, if their respective content is relatively high. Other groups of substances of biotechnological origin cannot be detected due to the separation conditions and the detection principle of the TLC-method. Therefore new methods had to be developed. In accordance with the guidelines of the International Conference of Harmonisation (ICH), the content of unknown impurities in active ingredients for oral therapeutics should be limited to 0,1 % w/w. Apart from other amino acids, the study included peptides, amino sugars and nucleic acids as potential impurities, originating from production or purification processes. These additional groups of substances are byproducts of the biosynthesis pathways of microorganisms. An attempt was made to quantify the amino acids, peptides and amino sugars by means of capillary electrophoresis. UV-spectrophotometry was additionally used for the determination of nucleic acids. KW - Aminosäuren KW - Verunreinigung KW - Fermentation KW - Kapillarelektrophorese KW - Aminosäuren KW - Verunreinigugsprofil KW - Fermentation KW - Kapillarelektrophorese KW - amino acids KW - impurity profile KW - fermentation KW - capillary electrophoresis Y1 - 2002 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-4106 ER - TY - THES A1 - Ilko, David T1 - The use of charged aerosol detection for the analysis of excipients and active pharmaceutical ingredients T1 - Die Verwendung des "Charged Aerosol Detectors" zur Analytik von Hilfs- und Wirkstoffen N2 - The Corona® charged aerosol detector (CAD) is an aerosol-based detector first de-scribed by Dixon and Peterson in 2002. It is capable of detecting compounds inde-pendent from their physico-chemical properties presumed the analyte is sufficiently non-volatile. Consequently, the CAD is often applied to the analysis of substances that do not possess a suitable UV chromophore. Major drawbacks are however, the detector signal is non-linear and depending on the content of organic solvent in the mobile phase. This thesis tried to explore possible applications of the CAD for pharmaceutical analysis. Therefore, several substances from different compound classes were in-vestigated. Newly developed or existing methods were validated. Thus the perfor-mance of the CAD could be examined. Both assay and impurity determination were evaluated for their compliance with ICH Q2(R1) “Validation of Analytical Proce-dures” and the “Technical Guide for the Elaboration of Monographs”. In the course of the establishment of reference substances at the EDQM, a generic screening method for the identification of organic and inorganic pharmaceutical counterions was needed. An HPLC-CAD method developed by Zhang et al. was therefore investigated for its suitability for pharmacopoeial purpose. Method valida-tion was performed. It was found that 23 ions could be separated and detected. Iden-tification was achieved via retention time of an authentic standard of the corre-sponding ions. Alternatively, peak assignment was performed by determination of the exact mass using TOF-MS. Ions could be quantified as impurities or for stoichi-ometric purpose. For the impurity control in topiramate, the performance characterstics of the CAD were compared to that of an ELSD. CAD was superior to ELSD in terms of repeata-bility, sensitivity and linearity. However, impurities could be quantified with satisfac-tory accuracy with both detectors. The application of the ELSD was not feasible due to non-reproducible spike peaks eluting after the principle peak in the chromatogram of the test solution. One of the impurities, topiramate impurity A (diacetonide), gave no or a vastly diminished signal in the ELSD and the CAD, respectively. It is evapo-rated during the detection process due to its relatively high vapor pressure. The re-sponse could be enhanced by a factor of nine via post-column addition of acetoni-trile and a lower nebulizer temperature. As the response of topiramate impurity A was still about thousand-fold lower than the response of all other impurities, its quantification was not feasible. Additionally, the HPLC-CAD was successfully vali-dated as an assay procedure for topiramate. There seems to be a great potential in the application of the CAD to the analysis of excipients as most compounds do not possess a suitable UV chromophore. Here, a simple and rapid HPLC-CAD method for the determination of polidocanol (PD) was developed. The method was successfully validated as a potential assay procedure for the Ph. Eur. as none is described in either of the two PD monographs. The same method was applied to the determination of the PD release from a pharmaceutical polymer matrix. A method for the determination of the fatty acid (FA) composition of polysorbate 80 (PS80) was developed and validated. Using the CAD and mass spectrometry, we were able to identify two new FAs in 16 batches from four manufacturers. All batch-es complied with pharmacopoeial specification. Furthermore, the overall composi-tion of the different PS80 species (“fingerprinting”) and the peroxide content were determined. In addition to the chemical characterization, functionality related charac-teristics (FRCs) were determined. Correlations between chemical composition and FRCs were found. The validation data of the above mentioned methods suggests that the CAD repre-sents a viable detection technique for pharmaceutical analysis. The CAD was suffi-ciently sensitive for non-volatile analytes. Impurity control down to concentrations of 0.05 or 0.03%, as demanded by ICH Q3A (R2), is achievable. However, the response of semi-volatile compounds may be drastically diminished. It could be confirmed that the response of the CAD is linear when the range does not exceed two orders of magnitude. Exceptions may be observed depending on the actual method setup. When the measuring range is sufficiently narrow, quantification can be done using single-point calibration which is common practice in pharmaceutical anlysis. Impuri-ties may also be quantified against a single calibration solution. However, correction factors may be needed and the accuracy is considerably lower compared to an as-say method. If a compound is to be quantified over a large concentration range, log-log transformation of the calibration curve is needed and a decreased accuracy has to be accepted. N2 - Der “Corona® charged aerosol detector” (CAD) ist ein aerosol-basierter Detektor, welcher 2002 von Dixon und Peterson vorgestellt wurde. Damit lassen sich nicht-flüchtige Substanzen unabhängig von ihren physiko-chemischen Eigenschaften detektieren. Daraus folgt, dass der CAD oft zur Analyse von Substanzen ohne UV-Chromophor angewandt wird. Großes Manko ist jedoch, dass das Signal nicht linear und abhängig vom Anteil organischen Lösemittels in der mobilen Phase ist. Ziel dieser Arbeit war es, mögliche Anwendungen des CAD in der pharmazeuti-schen Analytik zu erschließen. Dies wurde anhand von Beispielen aus unter-schiedlichen Substanzklassen untersucht. Dabei wurden neu entwickelte oder be-stehende Methoden validiert um die Leistung des CAD beurteilen zu können. So-wohl Gehaltsbestimmungen als auch Methoden zur Erfassung von Verunreinigun-gen wurden hinsichtlich ihrer Konformität mit dem Europäischen Arzneibuch (Ph. Eur.) geprüft. Im Zuge der Charakterisierung von Referenzsubstanzen beim EDQM wurde eine Methode zur Identifikation von pharmazeutischen Gegenionen benötigt. Zu diesem Zweck wurde eine HPLC-CAD-Methode von Zhang et al. hinsichtlich ihrer Eignung für das Ph. Eur. überprüft. Mit dieser Methode ließen sich 23 pharmazeutisch rele-vante Ionen trennen und detektieren. Die Ionen wurden durch Vergleich der Re-tentionszeiten eines Standards erreicht. Zusätzlich wurde die Peakzuordnung mit-tels der Bestimmung der Präzisionsmasse des Gegenions oder des Arzneistoffes durch ein TOF-MS durchgeführt. Die Methode ließ die Quantifizierung von Ionen als Verunreinigung oder zur Bestimmung der Stöchiometrie eines Salzes zu. Bei der Bestimmung von Verunreinigungen von Topiramat wurde ein Vergleich zwischen CAD und ELSD angestellt. Es zeigte sich, dass der CAD in den Punkten Wiederholbarkeit, Empfindlichkeit und Linearität überlegen war. Mit beiden Detekto-ren wurde eine ähnlich gute Richtigkeit erzielt. Durch das Auftreten von nicht re-produzierbaren Peaks, welche nach dem Hauptpeak im Chromatogramm der Testlö-sung auftraten, war die Anwendung des ELSD hier auszuschließen. Eine der Ver-unreinigungen, Topiramat Verunreinigung A (Diacetonid) lieferte kein bzw. ein ver-ringertes Signal in ELSD und CAD. Aufgrund des relativ hohen Dampfdrucks der Substanz wurde sie während des Detektionsvorgangs verdampft. Das Signal konn-te durch Zugabe von Acetonitril nach der Säule und durch eine Verringerung der Temperatur des Vernebler um das neunfache vergrößert werden. Da aber die Emp-findlichkeit für alle anderen Verunreinigungen dennoch um das tausendfache hö-her war, war eine Quantifizierung von Topiramat Verunreinigung A nicht möglich. Die HPLC-CAD Methode wurde zusätzlich als Gehaltsbestimmungsmethode für Topiramat validiert. Die Anwendung des CAD zur Analyse von Hilfsstoffen birgt großes Potenzial, da viele Substanzen nicht über ein Chromophor verfügen. Im Zuge dieser Arbeit wurde eine einfache und schnelle Methode zur Gehaltsbestimmung von Polidocanol (PD) entwickelt. Diese wurde als mögliche Methode für das Ph. Eur. validiert. Zusätzlich wurde die Methode zur Bestimmung der Freisetzung von PD aus einer pharmazeu-tischen Matrix verwendet. Es wurde eine Methode zur Bestimmung der Fettsäurezusammensetzung von Poly-sorbat 80 (PS80) entwickelt und validiert. Mittels CAD und Massenspektrometrie war es möglich zwei neue Fettsäuren in 16 Chargen von vier verschiedenen Herstellern zu identifizieren. Alle Chargen entsprachen den Anforderungen des Ph. Eur. Wei-terhin wurde die Zusammensetzung der einzelnen PS80-Spezies („fingerprinting“) sowie der Peroxidgehalt untersucht. Neben dieser chemischen Charakterisierung wurden auch funktionalitätsbezogene Eigenschaften (FRCs) bestimmt. Korrelatio-nen zwischen chemischen Zusammensetzung und FRCs wurden gefunden. Die Validierungsdaten der genannten Methoden legen nahe, dass der CAD sinn-voll zur pharmazeutischen Analytik angewendet werden kann. Für nicht-flüchtige Substanzen wurde stets eine ausreichende Empfindlichkeit erreicht. Somit können Verunreinigungen bis zu einer Konzentration von 0.05 bzw. 0.03%, wie von der ICH Richtlinie Q3A (R2) gefordert, quantifiziert werden. Jedoch kann das Detektorsignal bei halb-flüchtigen Substanzen stark erniedrigt sein. Es konnte bestätigt werden, dass sich das Detektorsignal über zwei Größenordnungen linear verhält. Abwei-chungen davon sind in Abhängigkeit der jeweiligen Methode möglich. Ist der Mess-bereich genügen klein, so kann ein Stoff mittels Einpunkt-Kalibrierung quantifiziert werden. Dieses Vorgehen sollte bei Gehaltsbestimmungen angewandt werden. Ebenfalls mittels Einpunkt-Kalibrierung können Verunreinigungen erfasst werden. Jedoch kann es notwendig sein, Korrekturfaktoren zu bestimmen. Die Richtigkeit ist hier deutlich niedriger als bei einer Gehaltsbestimmungsmethode. Über einen gro-ßen Konzentrationsbereich muss eine Ausgleichskurve mit log-log-Transformation verwendet werden. Die Richtigkeit ist hierbei ebenfalls geringer als bei einer Ge-haltsbestimmung. KW - Analyse KW - Chemische Reinheit KW - Verunreinigung KW - Detektor KW - Pharmazie KW - charged aerosol detector KW - pharmaceutical analysis KW - Analytik Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-118377 ER - TY - THES A1 - Deubel, Alexandra T1 - Charakterisierung des Verunreinigungsprofils von Erythromycin mittels chromatographischer Methoden und massenspektrometrischer Detektion T1 - Characterization of the Impurity Profile of Erythromycin by means of chromatographic methods and mass spectrometric Detection N2 - Im Rahmen der vorliegenden Arbeit wurden analytische Methoden zur Bestimmung des Verunreinigungsprofils von Erythromycin entwickelt, die der bestehenden Ph.Eur.-Methode überlegen sind. Die neue HPLC-Methode ist in der Lage, alle verwandten Verbindungen mit angemessener Präzision nachzuweisen und zu quantifizieren. Mit Hilfe der Massenspektrometrie konnten alle Hauptkomponenten und verwandten Verbindungen der Base, ihrer Ester und Salze eindeutig identifiziert und quantifiziert werden. Zudem konnten zwei neue verwandte Verbindungen von Erythromycin gefunden und als N,N-Didemethylerythromycin A und Anhydroerythromycin F identifiziert werden. N2 - Within this work analytical methods for determination of the impurity profile of erythromycin were developed. These methods show clear improvements compared to the current methods described in the Ph.Eur. The new HPLC method is able to separate and quantify all related substances with an acceptable precision. The mass spectrometry shows the suitability for the direct qualitative and quantitative analysis of the base, ester and salts of erythromycin. Moreover using ion trap two new, unexpected EA related substances could be detected and identified as N,N-didemethylerythromycin A and anhydroerythromycin F. KW - Erythromycin KW - Verunreinigung KW - HPLC KW - Massenspektrometrie KW - Erythromycin KW - HPLC KW - MS KW - Verunreinigungsprofil KW - neue Verunreinigungen KW - erythromycin KW - HPLC KW - mass spectrometry KW - new impurities Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-20160 ER - TY - THES A1 - Borst, Claudia T1 - Kapillarelektrophoretische Reinheitsanalytik verschiedener Arzneistoffe des Europäischen Arzneibuchs T1 - Capillary electrophoretic impurity analysis of different drugs of the European Pharmacopoeia N2 - Die Kapillarelektophorese (CE), deren Trennprinzip auf der Wanderung geladener Teilchen im elektrischen Feld basiert, ist eine Methode, die in verschiedenen Techniken angewandt werden kann. Sowohl die wässrige Kapillarzonenelektrophorese (CZE) als auch die wasserfreie CE (NACE), aber auch die elektrokinetische Chromatographie mittels Mikroemulsion (MEEKC) wurden in dieser Arbeit für die Reinheitsanalytik der im Europäischen Arzneibuch beschriebenen Wirkstoffe Ethambutol, Quetiapin, Ephedrin sowie Levodopa und deren jeweils strukturverwandter Substanzen benutzt. Der Wirkstoff Ethambutol wird in der (S,S)-Form verwendet, die im Ph. Eur. 7 als Dihydrochlorid aufgeführt ist. Um eine Trennmethode für (S,S)-Ethambutol, sein Enantiomer und die achirale meso-Verbindung entwickeln zu können, wurden die beiden stereoisomeren Verunreinigungen aus 2-Amino-1-butanol und Diethyloxalat synthetisiert. Zur Trennung dieser drei Ethambutol-Isomere wurde CZE als Methode gewählt. In saurem Phosphatpuffer musste eine hohe Probenkonzentration von 1 mg/ml verwendet werden, um die Substanzen mit UV detektieren zu können (λ: 200 nm). In alkalischem Tetraboratpuffer war das Chromophor dank der freien Elektronenpaare der Stickstoff-Moleküle besser ausgeprägt und die Intensität der Peaks deutlich intensiver. Als chirale Selektoren wurden die nativen α-, β- und γ-Cyclodextine (CDs) und verschiedene derivatisierte β-CDs eingesetzt. Die Methode wurde vielfach in Bezug auf Molarität und pH-Wert der Puffer, Konzentration der verschiedenen chiralen Selektoren, Spannung und Temperatur modifiziert. Jedoch konnte keine Trennung der Stereoisomere erreicht werden. Eine CD-modifizierte MEEKC-Methode wurde herangezogen, um die Racemate der Aminosäuren Dopa, Methyldopa, Tyrosin und Phenylalanin voneinander zu trennen. Dazu wurde eine Mikroemulsion (ME) aus Ethylacetat, SDS, 1-Butanol, Phosphatpuffer, sulf. β-CD und, wenn nötig, aus dem organischen Modifier 2-Propanol eingesetzt. Für jede DL-Aminosäure wurde die Zusammensetzung der ME als auch die Geräteeinstellungen (Spannung, Temperatur) optimiert. Die Trennung von DL-Dopa konnte ohne Zugabe eines organischen Modifiers durchgeführt werden. Auf Grundlage dieser individuellen Methoden wurden zwei CD-modifizierte MEEKC-Methoden entwickelt, mit denen alle vier untersuchten Racemate getrennt werden konnten. Die abschließende Validierung in Bezug auf Wiederholpräzision (Auflösung, Migrationszeiten, Verhältnis der korrigierten Peakflächen und Anzahl der theoretischen Böden) und Detektionsgrenzen zeigte, dass die Methoden präzise Ergebnisse liefern. Die Technik der MEEKC wurde auch zur Trennung von Ephedrin-Derivaten genutzt. Wedig et al. konnten die Racemate von Ephedrin, Pseudoephedrin, N-Methylephedrin und Norephedrin mit einer HDAS-β-CD-modifizierten CZE-Methode in einem Lauf basislinientrennen, indem ein 50 mM Phosphatpuffer, pH 3,0 als HGE eingesetzt wurde. Aus diesem HGE und den organischen Bestandteilen, die zur Trennung der Aminosäuren führten, wurde eine ME hergestellt. Entgegen der Methode von Wedig et al. konnte mittels HDAS-β-CD keine zufriedenstellende Trennleistung erreicht werden. Durch Austausch des chiralen Selektors gegen sulf. β-CD und Modifizierung des Phosphatpuffers in Ionenstärke und pH-Wert konnte für alle vier Epedrin-Derivate eine Basislinientrennung erzielt werden. Diese MEEKC-Methode wurde auf weitere Ephedrin-Derivate angewandt, wodurch das racemische 2-(Dibutylamino)-1-phenyl-1-propanol partiell, die Racemate von Adrenalin, 2-Amino-1-phenylethanol und Diethylnorephedrin vollständig voneinander getrennt werden konnten. Während mit der HDAS-β-CD-modifizierten CZE-Methode alle vier Ephedrin-Derivaten in einem Lauf getrennt werden konnten, hat die MEEKC-Methode den Vorteil mit dem kostengünstigeren sulf. β-CD auszukommen. Schlussendlich wurde eine Reinheitsanalytik von Quetiapin und seinen verwandten Substanzen Quetiapindesethanol, Quetiapin-N-Oxid und Quetiapinlactam entwickelt. Da Quetiapinlactam fast ausschließlich in organischen Lösungsmitteln löslich ist, sollte eine wasserfreie CE-Methode (NACE) eingesetzt werden. Zwar konnte eine Methode entwickelt werden, deren HGE aus Methanol, Acetonitril, Ammoniumacetat und Essigsäure bestand, und mit der Quetiapin und seine drei verwandten Substanzen sehr gut getrennt werden konnten. Allerdings konnte sie aufgrund von Stromabbrüchen nicht validiert werden. Alternativ wurde eine wässrige, gut reproduzierbare CZE-Methode gefunden, deren Elektrolytlösung aus einem 80 mM Phosphatpuffer, pH 4.0 bestand. Aufgrund der Wasserunlöslichkeit von Quetiapinlactam konnten so nur Quetiapin und die Verunreinigungen Quetiapindesethanol und Quetiapin-N-Oxid erfasst werden. Abschließend wurde die CZE-Methode validiert, wodurch die hohe Präzision der ermittelten Werte gezeigt werden konnte. N2 - The separation mechanism of capillary electrophoresis (CE) is based on the mobility of ions in an electric field. CE is a versatile technique, which can be operated in different modes. In this work, both aqueous capillary zone electrophoresis (CZE) and nonaqueous CE (NACE) and microemulsion electrokinetic chromatography (MEEKC) were investigated. Using these CE methods, impurity analysis was accomplished for serveral pharmaceuticals, which are described in the European Pharmacopoeia (Ph. Eur.): ethambutol, quetiapine, ephedrine, levodopa and correspondingly related substances. The active agent ethambutol is used in the (S,S)-configuration and in Ph. Eur. 7 the monograph describes the dichloride of the substance. In order to develop a separation method for (S,S)-ethambutol, its enantiomer and the achiral meso-compound were synthesized by the reaction of 2-amino-1-butanol and diethyloxalate. For the separation of these ethambutol compounds the CZE technique was chosen. After using an acid phosphate buffer, the concentration of the sample solution had to be set at 1 mg/ml for an sufficient UV adsorption (λ: 200 nm). After using a basic tetraborate buffer, the chromophore was more sensitive due to the electron pair of the nitrogen molecule, which led to higher peak intensity. Native α-, β- and γ-cyclodextins (CDs) and some derivatives of β-CD were added to the background electrolyte (BGE) as chiral selectors. The CZE method was modified in many ways, e. g. in molarity and pH value of the BGE, in concentration of the chiral selectors, in voltage and in temperature. In spite of various variations, the separation of the stereoisomers was not successful. A CD-modified MEEKC method was applied to separate the racemates of dopa, methyldopa, tyrosine and phenylalanine. For this purpose, a microemulsion (ME) was employed, which consisted of ethyl acetate, SDS, 1-butanol, phosphate buffer, sulf. β-CD and 2-propanol, used as an organic modifier, if necessary. For each DL-amino acid the composition of the ME and the instrument settings (voltage, temperature) were optimized. The separation of DL-dopa was accomplished without an organic modifier. Based on the methods evolved individually, two CD-modified MEEKC methods were developed to separate all four racemates. The concluding validation of these methods with respect of repeatability (resolution, migration time, ratio of the corrected peak areas, and number of theoretical plates) and limit of detection showed that the methods give precise results. The technique of MEEKC was also used for the separation of ephedrine derivatives. By means of a HDAS-β-CD-modified CZE method, Wedig et al. achieved baseline separation of racemic ephedrine, pseudoephedrine, N-methylephedrine and norephedrine in one run. In their experiment the BGE consisted of 50 mM phosphate buffer, pH 3.0. An ME was composed of this buffer as aqueous phase and the organic compounds, which formed the oil-phase of the ME for the amino acids. Contrary to the CZE method of Wedig et al., who used HDAS-β-CD, no satisfying resolution was observed. Replacing the chiral selector HDAS-β-CD with sulf. β-CD and modifying the phosphate buffer in ionic strength and pH value, led to baseline separation of the four mentioned ephedrine derivatives eventually. This MEEKC method was subjected to the separation of other ephedrine derivatives. So racemic 2-(dibutylamino)-1-phenyl-1-propanol could partly be separated, whereas complete separation could be observed for racemic adrenaline, 2-amino-1-phenylethanol and diethylnorephedrine. Whereas the MEEKC method is much cheaper by using sulf. β-CD, the application of the HDAS-modified CZE method resulted in the separation of all four racemic ephedrine alkaloids in one run. Finally, an impurity analysis of quetiapine and its related compounds quetiapine desethanol, quetiapine-N-oxide and quetiapine lactam was develop. The molecular structure of quetiapine lactam needed to be clarified, as this compound had not been described before. By using mass spectrometric (MS) as well as infrared (IR) and NMR investigations, the substance could be identified: Dibenzo[b,f][1,4]thiazepine-11(10H)one. As quetiapine lactam was found to be nearly insoluble in water and aqueous solutions, an NACE method had to be applied. Indeed, a method was developed with a BGE consisting of methanol, acetonitril, ammonium acetate and acetic acid. Thereby, the separation of quetiapine and its three mentioned impurities was observed with high resolution values. However, validation was impossible, because of numerous aborts of the current. Alternatively, an aqueous and highly reproducible CZE method was found with a BGE composed of 80 mM phosphate buffer, pH 4.0. Due to the water insolubility of quetiapine lactam, only quetiapine desethanol and quetiapine-N-oxide could be analysed as impurities. Finally, the aqueous CZE method was validated; the high precision of the results could be verified. KW - Kapillarelektrophorese KW - Arzneimittel KW - Verunreinigung KW - Qualitätskontrolle KW - Europäisches Arzneibuch KW - chirale Trennung KW - Ethambutol KW - Aminosäuren KW - Ephedrin KW - Quetiapin KW - MEEKC KW - CZE KW - NACE KW - Cyclodextrine KW - capillary electrophoresis KW - chiral separation KW - cyclodextrin KW - amino acids Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-56243 ER -