TY - THES A1 - Hofmann, Michael Peter T1 - Physikalische Charakterisierung von Calciumphosphat-Pulvern zur Einstellung von Prozessparametern für die Herstellung von Knochenzement T1 - Physical characterisation of calcium phosphate powders for the adjustment of processing parameters for the fabrication of bone cement N2 - Die Arbeit behandelt die physikalische Charakterisierung der Herstellung einer Tetracalciumphosphat (TTCP) / Calciumhydrogenphosphat (DCPA) Pulvermischung zur Anwendung als Knochenzement. Ziel war die Gewinnung einer Korrelation von Prozessparametern mit anwendungsrelevanten Zementeigenschaften, also hohe mechanische Festigkeit, definierte Abbindezeit, physiologischer pH-Wert-Verlauf und Reproduzierbarkeit. Die Einstellung eines physiologischen pH-Werts im Bereich 7-8 der Zementpaste erfordert eine geeignete Lösungsrate beider Pulverkomponenten. Dies gelingt durch Mahlung mit einer Einstellung der mittleren Partikelgröße von 10-20 µm (TTCP) und 0,5-2 µm (DCPA). DCPA wird nass gemahlen; das Suspensionsmedium dient der Agglomerationsverminderung, da bei Partikelgrößen von 0,5-2 µm interpartikuläre Kräfte gegenüber der Gewichtskraft dominieren. TTCP wurde durch Sinterung von DCPA und Calciumcarbonat bei 1500°C hergestellt und trocken vermahlen. Die Ermittlung der mittleren Partikelgrößen und relativen Breite der Partikelgrößenverteilungen, der sogenannten Spanne, nach Mahlung erfolgte durch Laserstreuung und Auswertung der Streumuster nach der Mie-Theorie. Mahlungen von TTCP führen zu Feinkornanteilen mit Partikelgrößen < 1 µm, die eine gleichmäßige Lösungsrate zu Beginn der Abbindereaktion verhindern. Durch Variation der Mahlparameter kann dieser Feinkornanteil minimiert werden. Dennoch besteht die Notwendigkeit, Abbinde-Beschleuniger auf Natriumphosphat (NaP)-Basis zu verwenden, um die erhöhte Lösungsrate der TTCP-Komponente zu kompensieren. Kriterium für die Auswahl des geeigneten Suspensionsmediums für die Nassmahlung von DCPA ist das Zetapotential von DCPA-Partikeln in flüssiger Phase, welches durch Laser-Doppler-Elektrophorese gemessen wird. Die Messungen zeigen, dass sich das Zetapotential mit Partikelgröße und Spanne korrelieren lässt. Hohe Zetapotential-Werte zu Beginn der Mahlung führen zu kleiner Endpartikelgröße. Das Zetapotential von gemahlenen DCPA-Pulvern steigt bei der Mahlung an und bestimmt die minimale Spanne. Partikelgröße und Spanne bestimmen über die effektive Viskosität außerdem das Ende des Mahlvorgangs. Als Suspensionsmedium zur Einstellung kleiner Partikelgröße bei gleichzeitig geringer Spanne eignet sich Reinstwasser, gefolgt von Ethylenglykol und Ethanol. Es lassen sich mittlere Partikelgrößen von 0,6 µm bei einer Spanne von 1,0 realisieren. Die Mahlung setzt neben der Partikelgröße die Kristallinität von DCPA und TTCP herab, durch eine mechanisch induzierte Phasenumwandlung in den amorphen Zustand. Röntgendiffraktometrische Untersuchungen, XRD, der Pulver zeigen eine Abnahme der Intensität der Beugungsreflexe um ca. 50% für TTCP und ca. 30% für DCPA nach 24h. Die Auswertung der Beugungsspektren durch Rietveld-Analyse ergibt gleichzeitig eine kontinuierliche Abnahme der mittleren Kristallitgröße. Die Bildung amorpher Anteile resultiert für TTCP in abbindefähigen, einkomponentigen Zementen, die im stark basischen Bereich mit 2.5%iger Na2HPO4-Lösung Hydroxylapatit und Calciumhydroxid bilden. Hochkristallines TTCP ist dagegen nicht reaktiv, bedingt durch die Ausbildung einer Hydroxylapatitschicht um die Partikel. Suspensionsmedium und Luftfeuchtigkeit bewirken eine Kontamination der feinkörnigen Pulver. Stickstoffadsorptions-Messungen, BET, zeigen die Lokalisation des Kontaminats auf der kompakten, nicht porösen Partikeloberfläche. Der Anteil an nicht entfernbarem Suspensionsmedium, bestimmt durch Thermogravimetrie, liegt bei 3-5% nach Trocknung an Luft und lässt sich auf < 1% bei Vakuumtrocknung reduzieren. Während organische wasserlösliche Kontaminationen keinen Einfluss auf die Lösungsrate und Reaktivität von DCPA ergeben, führt Wasser als Suspensionsmedium bzw. das Einwirken von Luftfeuchtigkeit auf die getrockneten Pulver zu einer starken Herabsetzung der Reaktivität. Ursache ist die Ausbildung einer diffusionshemmenden Hydroxylapatit-Schicht um die Partikel durch Hydrolyse der Calciumphosphate. DCPA, durch Mahlung in Wasser inaktivierend kontaminiert, zeigt die niedrigste Lösungsrate, trotz großer spezifischer Oberfläche. Die Mischung der Pulver erfolgt durch Selbstmischung bei geringer mechanischer Krafteinleitung; die hochdispersen DCPA-Partikel agglomerieren aufgrund interpartikulärer van-der-Waals-Kräfte an den großen TTCP-Partikeln. Ausgehärtete Zemente zeigen eine Korrelation zwischen der Druckfestigkeit und der Partikelgröße, sowie eine Korrelation von Zugfestigkeit und Spanne der Partikelgrößenverteilung von DCPA. Ein erhöhter Feinkornanteil des TTCP-Pulvers führt zur Reduktion der mechanischen Festigkeit. Die vorgestellte physikalische Charakterisierung der TTCP/DCPA- Pulverherstellung führt zu einem Medizinprodukt mit Druckfestigkeiten von 75 MPa und Zugfestigkeiten von 12 MPa. Abbindezeit und pH-Wert-Verlauf bei der Aushärtung lassen sich durch die Konzentration von NaP-Abbindebeschleunigern einstellen. N2 - This thesis is about the physical characterisation of the fabrication process of a Tetracalciumphophate (TTCP) / Calciumhydrogenphosphate (DCPA) bone cement powder mixture. The goal was to achieve a correlation between processing parameters and application relevant properties of the cement matrix, i.e. high mechanical strength, defined setting time, physiological pH-value and reproducibility. For the adjustment of a physiological pH-value between 7 and 8 of the cement paste it is necessary to adjust the solubility rate of both powder components. This is done by adjusting the medium particle size of TTCP and DCPA to 10-20 µm respectively 0,5-2 µm. DCPA is wet milled; the suspension medium has to prevent agglomeration, because at particle sizes between 0,5-2 µm attractive interparticular forces dominate over the deagglomerating weight of the powder particles. TTCP is fabricated by sintering a DCPA / Calciumcarbonate mixture at 1500°C and dry milling it. The measurement of medium particle size and the relative width of the particle size distribution, the so called span, after milling were done by laser diffraction and calculation following Mie-theory. The milling of TTCP leads to a fine powder fraction with particle sizes below 1 µm, which prevents a uniform solubility rate at the beginning of the setting reaction. This fine powder fraction can be minimized by variation of the milling parameters. Nonetheless it is necessary to use sodium phosphate setting-accelerators to equalise the higher solubility rate of the TTCP-cements component. Criteria for choosing the suspension medium for the wet milling of DCPA is the zeta potential of DCPA particles in liquid phase, measured by Laser Doppler Electrophoresis (LDE). The measurements indicate that the zeta potential is correlated with particle size and span. A high zeta potential value at the start of the milling process leads to a small final particle size. The zeta potential of milled DCPA rises with the milling process and defines the minimum span. Particle size and span determine the effective viscosity and therefore the end of the milling process. For achieving a small particle size together with a small span distilled water is most suitable, followed by ethylene glycol and ethyl alcohol. A medium particle size of 0,6 µm together with a span of 1,0 can be realised. The milling process is also reducing the cristallinity of DCPA and TTCP by a mechanically induced phase change to the amorphous state. X-Ray diffraction measurements of the powders after 24h of milling show an intensity decrease of the diffraction patterns by almost 50% for TTCP and almost 30% for DCPA. The analyses of the diffraction patterns by Rietveld-analysis show a continuous decrease of the medium crystallite size at the same time. The formation of amorphous TTCP fractions results in a one component cement able to set in a high pH-regime. High cristallinity TTCP is not reactive due to the hydroxyapatite layer on the particle surface. The suspension medium and humidity are causing a contamination of the powder particles. Nitrogenadsorption measurements, BET, are showing that the contaminant is located on the compact non-porous particle surface. The fraction of not extractable suspension medium, determined by thermogravimetry, is in the region of 3-5% after drying in air and can be reduced to less than 1% by drying in vacuum. Organic watersoluble contamination does not lead to changes in solubility rate or reactivity of DCPA particles. Water as suspension medium or humidity reduces the reactivity significantly. The reason is a hydroxyapatite layer on the DCPA particles caused by hydrolysis of the calciumphosphate leading to decreased diffusion. Water milled DCPA is showing the lowest solubility rate despite having the highest specific surface area. The two powder components are literally self mixing. The disperse DCPA particles are agglomerating on the surface of the larger TTCP particles due to attractive van-der-Waals-forces. The hardened cement matrix is showing a correlation between compressive strength and particle size and between diametral tensile strength and the span of the particle size distribution. An increase of the fine powder fraction of TTCP leads to a decrease in mechanical strength. The physical characterisation of the fabrication process of a TTCP/DCPA-cement powder mixture leads to a medical device with a compressive strength of 75 MPa and a diametral tensile strength of 12 MPa. Setting time and pH-value can be adjusted by the amount of sodium phosphate setting-accelerator. KW - Knochenzement KW - Herstellung KW - Calciumphosphate KW - Pulver KW - Knochenzement KW - Calciumphosphat KW - Kontamination KW - Mahlprozess KW - Physikalische Charakterisierung KW - bone cement KW - calcium phosphate KW - contamination KW - milling process KW - physical characterisation Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-7315 ER - TY - THES A1 - Helf, Christian T1 - Herstellung von Polymethacrylat/Calciumphosphat-Implantatwerkstoffen durch den 3D-Pulverdruck T1 - Preparation of polymethacrylate/calcium phosphate implant materials via 3D powder printing N2 - Die Erstellung von komplex geformtem Knochenersatz wurde durch den 3D-Pulverdruck unter Verwendung von Calciumphosphatmaterialien beschrieben. Gegenstand der vorliegenden Arbeit war deren Modifikation durch die Verwendung von Methacrylatkunststoffen. Ziel war es, durch die Infiltration von nicht resorbierbaren Kunststoffen, wie sie in kommerziell erhältlichen Knochenzementen verwendet werden, die mechanischen Eigenschaften der nicht gesinterten Keramikstrukturen zu verbessern. Getestet wurden verschiedene Methoden der Infiltration sowie der nachfolgenden Polymerisationsinitiierung durch chemische, thermische oder photochemische Aktivatoren. Daneben erfolgte der Druck von Tricalciumphosphat-Pulvern, die mit Polymethylmethacrylat Partikeln versetzt wurden und durch eine hydraulische Verfestigungsreaktion mit Phosphorsäure aushärten. Die erstellten Materialien wurden auf ihre Porosität, ihre mechanischen Eigenschaften sowie auf die Phasenzusammensetzung ihrer anorganischen Matrix und den Konversionsgrat ihrer organischen Komponente hin untersucht. Es gelang, die freie Porosität der Calciumphosphat-Matrix durch Verwendung von flüssigen, monomeren Kunststoffen zu füllen und diese durch eine thermische Initiierung der radikalischen Polymerisation vollständig zur Aushärtung zu bringen. Bei der Reaktion kommt es neben einer Polymerisationskontraktion im organischen Bestandteil der Kunststoffe zu einer Phasenumwandlung der Bruschitanteile der Calciumphosphat-Matrix. Proben, die mit einem flüssigen Bisphenol-A-Derivat versetzt wurden, zeigten eine Verdreifachung ihrer Festigkeit und erreichten maximale Druckfestigkeiten von 99 MPa, Biegefestigkeiten von 35 MPa und einen E-Modul von 18 GPa. Verglichen mit den biomechanischen Eigenschaften des physiologischen Hartgewebes liegen die Werte damit deutlich über denen von spongiösem und unter denen von kortikalem Knochen. Eine künftige Optimierung erscheint durch die Schaffung einer chemischen Verbundphase zwischen dem anorganischen Calciumphosphat-Gefüge und den Polymerbestandteilen als aussichtsreich. N2 - The production of complex shaped bone graft was described by the 3D powder printing using calcium phosphate materials. The present work dealt with the modification of these materials by adding methylacrylate materials. The objective was to improve the mechanical properties of non-sintered ceramic structures by the infiltration of non-resorbable plastics such as used in commercialized bone cements. Different methods of infiltration as well as chemical, thermal or photochemical polymerization activators have been tested. In addition to that, tricalcium phosphate powders have been enriched by polymethylmethacrylate particles before being printed and cured by an hydraulic hardening reaction with phosphoric acid. The prepared materials have been tested for their porosity, their mechanical properties as well as for the phase composition of their inorganic matrix and the conversion rate of their organic components. It could be achieved to fill the open porosity of printed calcium phosphate matrix by using liquid, monomeric plastics and to cure them completely through a thermal initiation of radical polymerization. Besides the polymerization contraction in the organic component, the thermal treatment led to a phase transformation of the calcium phosphate brushite matrix. Samples, which were infiltrated with a liquid bisphenol-A derivative, showed a threefold increase of their strength and reached a maximum compressive strength of 99 MPa, a flexural strength of 35 MPa and a Young´s modulus of 18 GPa. Compared to biomechanical properties of physiological hard tissues, the levels were significantly higher than those of cancellous and lower than those of cortical bones. To further optimize, it seems promising to create a chemical bond between the inorganic phase of calcium phosphate microstructure and polymer components. KW - Rapid Prototyping KW - Knochenersatz KW - Knochenzement KW - Methacrylsäuremethylester KW - 3D-Pulverdruck KW - Calciumphosphat KW - Rapid Prototyping KW - 3D powder print KW - bone cements KW - methacrylate KW - calcium phosphate Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-39575 ER - TY - THES A1 - Vorndran, Elke T1 - Rapid-Prototyping hydraulisch härtender Calcium- und Magnesiumphosphatzemente mit lokaler Wirkstoffmodifikation T1 - Rapid-prototyping of hydraulic calcium- and magnesium phosphate cements with local drug modification N2 - Ziel dieser Arbeit war die Herstellung individuell formbarer Strukturen mittels des 3D-Pulverdrucks auf Basis von bei Raumtemperatur hydraulisch abbindenden Knochenzementpulvern. Neben der Entwicklung neuartiger Zementformulierungen auf Basis von Magnesiumphosphaten war vor allem die gleichzeitige Ausstattung der Werkstoffe mit temperaturlabilen und bioaktiven Verbindungen ein wichtiger Entwicklungsschritt. Die Lokalisation der Wirkstoffe korreliert dabei mit entsprechenden Farbinformationen im Design der Konstrukte, die durch einen Mehrfarbendrucker physikalisch abgebildet werden. Das auf Calciumphosphat basierende System hat den Nachteil, dass die Abbindereaktion bei stark sauren pH-Werten abläuft, was negative Auswirkungen auf die gleichzeitige Ausstattung mit sensitiven Wirkstoffen hat. Zur Lösung dieser Problematik wurde ein neues Knochenzementpulver auf Magnesiumphosphatbasis entwickelt, welches unter neutralen pH-Bedingungen mit ammoniumhaltigem Binder zu dem Mineral Struvit abbindet. Das Zementpulver aus Trimagnesiumphosphat wurde bezüglich der pulvertechnologischen Eigenschaften, wie Partikelgröße, Partikelgrößenverteilung, Glättungseigenschaften und Schüttdichte sowie hinsichtlich des Abbindeverhaltens charakterisiert und für den Druckprozess optimiert. Die hohe Strukturgenauigkeit ermöglichte die Darstellung von makroporösen Strukturen mit einem minimalen Porendurchmesser von ca. 200 µm. Gute mechanische Kennwerte der gedruckten Strukturen, sowie eine hohe Umsetzungsrate zur gewünschten Phase Struvit wurden durch eine Nachhärtung in Ammoniumphosphatlösung erhalten. Die Druckfestigkeit betrug > 20 MPa und der Phasenanteil von Struvit konnte auf insgesamt 54 % gesteigert werden. Die Darstellung von wirkstoffmodifizierten Calciumphosphat- und Magnesiumphosphatstrukturen durch Verwendung eines Mehrfarbendruckers wurde beginnend vom Design der Strukturen bis hin zur experimentellen Bestimmung der Korrelation von Farbinformation und Binderapplikation etabliert. Zur Sicherstellung einer hohen Druckqualität und der Ortsständigkeit gedruckter Wirkstoffe erwies sich eine zusätzliche Modifikation des Tricalciumphosphatpulvers mit quellfähigen Polymeren (Hydroxypropylmethyl-cellulose (HPMC) bzw. Chitosan) als erfolgreich. Eine maximale Auflösung von ca. 400 µm konnte für eine HPMC/Chitosan/Calciumphosphat-Variante erreicht werden, während das hochreaktive Magnesiumphosphat/Magnesiumoxid-System eine Auflösung von 480 µm aufwies. Die Ortsständigkeit eingebrachter Lösungen war Voraussetzung für die Steuerung der Freisetzungskinetik. Das Freisetzungsverhalten in vitro wurde in Abhängigkeit von der Wirkstofflokalisation (homogen, Depot, Gradient) innerhalb der Matrix und unter Einbringung zusätzlicher polymerer Diffusionsbarrieren für den Wirkstoff Vancomycin untersucht. Dabei zeigte sich, dass die Modifikation der Matrices mit Polymeren zu einer verzögerten Freisetzung führte. Die lokale Wirkstoffmodifikation der Matrices in Form eines Depots oder Gradienten hatte Einfluss auf die Freisetzungskinetik, wobei eine lineare Freisetzung mit der Zeit (Kinetik 0. Ordnung) erreicht werden konnte. Die applizierten Wirkstoffe umfassten sowohl niedermolekulare Verbindungen, wie etwa das Antibiotikum Vancomycin oder das Polysaccharid Heparin, als auch proteinbasierte Faktoren wie den Knochenwachstumsfaktor rhBMP-2. Beurteilt wurde die pharmakologische Wirksamkeit der Verbindungen nach dem Druck, sowie nach der Freisetzung aus einer Calciumphosphatmatrix für den Wirkstoff Vancomycin. Es konnte belegt werden, dass die biologische Aktivität nach dem Druckprozess zu über 80 % erhalten blieb. Limitierend war der stark saure pH-Wert bei bruschitbasierten Systemen, der zu einer Inaktivierung des Proteins führte. Diesem Problem könnte durch die Nutzung des neutral abbindenden Magnesiumphosphatsystems entgegengewirkt werden. Abschließend erfolgten eine mikrostrukturelle Charakterisierung der Calciumphosphat- und Magnesiumphosphatmatrices mittels µ-CT-Analyse und Heliumpyknometrie, sowie eine quantitative Phasenanalyse nach Rietveld. Experimentell konnte nachgewiesen werden, dass mit Hilfe des 3D-Pulverdruck die Darstellung von Makroporen > 200 µm möglich ist. Die Analyse der Phasenzusammensetzung ergab, dass die Umsetzungsrate von Tricalciumphosphat und Trimagnesiumphosphat zu den gewünschten Phasen Bruschit und Struvit infolge des Nachhärtungsprozesses signifikant gesteigert werden konnte. Im Zuge dessen nahm die Porosität der gedruckten Matrices der Phase Struvit von 58 % auf 26 % und der Phase Bruschit von 47 % auf 38 % ab. N2 - Aim of this study was the room temperature fabrication of individually formed structures via 3D-powder printing based on hydraulic bone cements. In addition to the development of a novel cement formulation composed of magnesium phosphate, the simultaneous modification of matrices during the printing process with temperature sensitive and bioactive drugs was an important part of the work. The drug localization within the matrices is hereby correlated with an analogous colour design of the structures, which is physically reproduced by the multi-colour-printer. The calcium phosphate based system has the disadvantage of a strongly acidic setting reaction, which has negative effects on the simultaneous modification with sensitive bioactive agents. To solve this problem a novel bone cement formulation based on magnesium phosphate was established. This cement reacts with ammonium based binder solution within seconds to form the mineral struvite at neutral pH. The technological properties of the of trimagnesium phosphate cement powder, including particle size, particle size distribution, spreadability, powder density, and the setting behaviour, were characterized and optimized for the printing process. The high structural accuracy enabled the production of macroporous structures with a minimal pore diameter of approximately 200 µm. Proper mechanical characteristics of the printed structures as well as a high degree of conversion to the struvite phase were achieved by post-hardening in ammonium phosphate solution. The compressive strength could be increased to more than 20 MPa and the phase fraction of struvite could be increased to a maximum value of a total of 54 %. The fabrication of drug loaded calcium phosphate and magnesium phosphate scaffolds using a multi-colour-printer was established, beginning with the structure design and following the experimental verification of the correlation between the colour information and the applied binder. To guarantee a high accuracy of printing and the localization of the printed drugs, a supplemental modification of the tricalcium phosphate powder with swellable polymers (hydroxypropylmethylcellulose (HPMC) or chitosan) was successful. A maximum resolution of about 400 µm was achieved by an HPMC/chitosan/calcium phosphate composition, whereas the highly reactive magnesium phosphate/magnesium oxide system showed a resolution of about 480 µm. The localization of the applied solutions was a prerequisite to control the release kinetics of the drugs. The release kinetic of vancomycin was investigated in vitro depending on the drug localization (homogeneous, depot, gradient-like) within the matrix and by adding additional polymeric diffusion barriers. It could be shown that the polymeric modification of the matrices resulted in a delayed drug release. By discrete and depot-like or graded drug distributions within the matrices the release kinetic could be controlled, achieving a linear release with time (zero order release). The administered agents involved both low molecular compounds like the antibiotic vancomycin or the polysaccharide heparin and protein based factors like bone morphogenic factor rhBMP-2. Evaluation of pharmacological activity of the agents after printing as well as after release of vancomycin from a calcium phosphate matrix was determined, indicating that the bulk biological activity of more than 80 % was retained during the printing process. The limiting factor of the brushite based system was the strong acidic pH, which resulted in an inactivation of protein-based bioactives. This problem may be solved by using neutrally setting magnesium phosphate systems. Finally a microstructural characterization of calcium phosphate and magnesium phosphate matrices by µ-CT analysis and helium pycnometry as well as a quantitative phase analysis by Rietveld was performed. It was demonstrated, that 3D-printing allows the manufacturing of macro pores > 200 µm. The analysis of phase composition showed a significant increase of the degree of conversion from tricalcium phosphate or trimagnesium phosphate to the phases brushite or struvite due to the post hardening process. Hence the porosity of the printed matrices decreased from 58 % to 26 % for struvite and from 47 % to 38 % for brushite. KW - 3D-Druck KW - Calciumphosphate KW - 3D Pulverdruck KW - Calciumphosphat KW - Magnesiumphosphat KW - 3D powder printing KW - calcium phosphate KW - magnesium phosphate KW - Magnesiumphosphate KW - Rapid Prototyping KW - Kontrollierte Wirkstofffreisetzung Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-70245 ER - TY - THES A1 - Spatz, Kerstin T1 - Mechanische und rheologische Eigenschaften von Calciumphosphat-Zementen T1 - Mechanical and rheological properties of calcium phosphate cements N2 - Zur Erhöhung der mechanischen Stabilität mineralischer Knochenzemente aus Calciumorthophosphaten (CPC) wurde in einem TTCP/DCPA-System das Zementedukt TTCP mit verschiedenen biokompatiblen Oxiden (SiO2, TiO2, ZrO2) während des Herstellungsprozesses dotiert. Dies führte zur Bildung von Calciummetallaten und einer Herabsetzung der Löslichkeit der TTCP-Komponente des Zements. Gegenüber einem oxidfreien Zement konnte die Druckfestigkeit von 65 MPa auf 80 MPa (SiO2) bzw. 100 MPa (TiO2) gesteigert werden. In einem zweiten Ansatz zur Verbesserung der Injizierbarkeit wurden die Wechselwirkungen der Partikeloberflächen mit der flüssigen Zementphase betrachtet. Durch biokompatible Additive sollte eine repulsive elektrostatische Wechselwirkung eingestellt werden, um Partikelagglomerate effektiv zu dispergieren und eine verflüssigende Wirkung zu erreichen. Die Injizierbarkeit eines TTCP/DCPA-Zements durch eine Kanüle mit 800 µm Durchmesser konnte durch die Verwendung von 500 mM tri-Natriumzitrat-Lösung aufgrund einer deutlichen Herabsetzung der Viskosität der Zementpaste signifikant gesteigert werden (>95%, P/L 3,3/1, Kraftaufwand 20 N). Abschließend wurde der Einfluss der Partikelgrößenverteilung auf die Festigkeit und Injizierbarkeit einer auf monomodaler Partikelgrößenverteilung basierten Zementmatrix untersucht. Hierzu wurden einem mechanisch aktivierten a-TCP-System unreaktive, feinkörnige Füllstoffpopulationen (TiO2, CaHPO4, CaCO3) zugesetzt und systematisch deren Effekt in Verbindung mit einer Partikelaufladung durch tri-Natriumzitrat auf die rheologischen und mechanischen Eigenschaften untersucht. Erst die Kombination einer bimodalen Partikelgrößenverteilung mit tri-Natriumzitrat-Lösung führte zu einer starken Erniedrigung der Viskosität, damit zur nahezu vollständigen Injizierbarkeit der Zemente und einer teilweise signifikanten Steigerung der mechanischen Festigkeiten (z.B. 72 MPa reiner a-TCP-Zement auf 142 MPa mit Zusatz von CaHPO4). N2 - An improvement of the mechanical strength of calcium phosphate bone cements in combination with a lower cement paste viscosity for better injectability was investigated. A first approach to improve the mechanical stability consisted in adding several biocompatible oxides (SiO2, TiO2, ZrO2) during the fabrication process of tetracalcium phosphate (TTCP). The formation of calcium metallates led to a decrease of the solubility of the oxide doped tetracalcium phosphates. The cements based on tetracalcium phosphates mixed with SiO2 and TiO2 exhibit a significant increase of the compressive strengths (65 MPa of pure cement up to 80 MPa (SiO2) and 100 MPa (TiO2)). A second approach to decrease the viscosity of CPC pastes considered the interactions between the particle surfaces and the liquid cement phase. To disperse agglomerates and improve the injection properties of CPC, biocompatible components were added to the liquid phase. As a result the injection properties of the TTCP/DCPA cement improved significantly. The use of 500 mM trisodium citrate solution as liquid phase changed the viscosity of the cement paste to a point, where complete injectability (> 95%) through an 800 mm diameter hypodermic needle could be achieved at low loads (20 N). In order to transfer the results of a multi-constituent cement to a single reactive component cement, different fine-particle-sized fillers were added to mechanically activated, monomodal α-tricalcium phosphate (α-TCP) cement. The inert fillers dicalcium phosphate anhydrous (DCPA), titanium dioxide (TiO2) and calcium carbonate (CC) were added to the α-TCP-matrix in different concentrations. For an effective ionic modification a 500 mM trisodium citrate solution was used as liquid phase as in the aforementioned TTCP/DCPA cement system. Only the combination of a bimodal particle size distribution and trisodium citrate solution led to a nearly complete injectability and a significantly increase of the mechanical stability of CPC. KW - Biomaterial KW - Knochenzement KW - Calciumphosphate KW - Implantatwerkstoff KW - Rheologie KW - Calciumphosphat KW - calcium phosphate KW - injectability KW - zetapotential KW - mechanical properties KW - tricalcium phosphate KW - Rheologie KW - Zetapotential KW - mechanische Eigenschaften Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-124860 ER - TY - JOUR A1 - Thibaudeau, Laure A1 - Taubenberger, Anna V. A1 - Holzapfel, Boris M. A1 - Quent, Verena M. A1 - Fuehrmann, Tobias A1 - Hesami, Parisa A1 - Brown, Toby D. A1 - Dalton, Paul D. A1 - Power, Carl A. A1 - Hollier, Brett G. A1 - Hutmacher, Dietmar W. T1 - A tissue-engineered humanized xenograft model of human breast cancer metastasis to bone JF - Disease Models & Mechanisms N2 - The skeleton is a preferred homing site for breast cancer metastasis. To date, treatment options for patients with bone metastases are mostly palliative and the disease is still incurable. Indeed, key mechanisms involved in breast cancer osteotropism are still only partially understood due to the lack of suitable animal models to mimic metastasis of human tumor cells to a human bone microenvironment. In the presented study, we investigate the use of a human tissue-engineered bone construct to develop a humanized xenograft model of breast cancer-induced bone metastasis in a murine host. Primary human osteoblastic cell-seeded melt electrospun scaffolds in combination with recombinant human bone morphogenetic protein 7 were implanted subcutaneously in non-obese diabetic/severe combined immunodeficient mice. The tissue-engineered constructs led to the formation of a morphologically intact 'organ' bone incorporating a high amount of mineralized tissue, live osteocytes and bone marrow spaces. The newly formed bone was largely humanized, as indicated by the incorporation of human bone cells and human-derived matrix proteins. After intracardiac injection, the dissemination of luciferase-expressing human breast cancer cell lines to the humanized bone ossicles was detected by bioluminescent imaging. Histological analysis revealed the presence of metastases with clear osteolysis in the newly formed bone. Thus, human tissue-engineered bone constructs can be applied efficiently as a target tissue for human breast cancer cells injected into the blood circulation and replicate the osteolytic phenotype associated with breast cancer-induced bone lesions. In conclusion, we have developed an appropriate model for investigation of species-specific mechanisms of human breast cancer-related bone metastasis in vivo. KW - breast cancer KW - bone metastasis KW - humanized xenograft model KW - melt electrospinning KW - tissue engineering KW - osteotropism KW - in vivo KW - stem-cell niche KW - human prostate-cancer KW - morphogenetic protein KW - osteoprogenitor cells KW - endochondral ossification KW - mouse model KW - trabecular bone KW - calcium phosphate KW - skeletal metastases Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-117466 VL - 7 IS - 2 ER - TY - JOUR A1 - Rödel, Michaela A1 - Baumann, Katrin A1 - Groll, Jürgen A1 - Gbureck, Uwe T1 - Simultaneous structuring and mineralization of silk fibroin scaffolds JF - Journal of Tissue Engineering N2 - Silk fibroin is commonly used as scaffold material for tissue engineering applications. In combination with a mineralization with different calcium phosphate phases, it can also be applied as material for bone regeneration. Here, we present a study which was performed to produce mineralized silk fibroin scaffolds with controlled macroporosity. In contrast to former studies, our approach focused on a simultaneous gelation and mineralization of silk fibroin by immersion of frozen silk fibroin monoliths in acidic calcium phosphate solutions. This was achieved by thawing frozen silk fibroin monoliths in acidic calcium phosphate solution, leading to the precipitation of monocalcium phosphate within the silk fibroin matrix. In the second approach, a conversion of incorporated -tricalcium phosphate particles into brushite was successfully achieved. Furthermore, a controlled cryostructuring process of silk fibroin scaffolds was carried out leading to the formation of parallel-oriented pores with diameters of 30-50 mu m. KW - Brushite KW - calcium phosphate KW - cryostructuring KW - hydrogel KW - mineralization KW - silk fibroin scaffolds Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-226427 VL - 9 ER - TY - JOUR A1 - Hettich, Georg A1 - Schierjott, Ronja A. A1 - Epple, Matthias A1 - Gbureck, Uwe A1 - Heinemann, Sascha A1 - Mozaffari-Jovein, Hadi A1 - Grupp, Thomas M. T1 - Calcium phosphate bone graft substitutes with high mechanical load capacity and high degree of interconnecting porosity JF - Materials N2 - Bone graft substitutes in orthopedic applications have to fulfill various demanding requirements. Most calcium phosphate (CaP) bone graft substitutes are highly porous to achieve bone regeneration, but typically lack mechanical stability. This study presents a novel approach, in which a scaffold structure with appropriate properties for bone regeneration emerges from the space between specifically shaped granules. The granule types were tetrapods (TEPO) and pyramids (PYRA), which were compared to porous CaP granules (CALC) and morselized bone chips (BC). Bulk materials of the granules were mechanically loaded with a peak pressure of 4 MP; i.e., comparable to the load occurring behind an acetabular cup. Mechanical loading reduced the volume of CALC and BC considerably (89% and 85%, respectively), indicating a collapse of the macroporous structure. Volumes of TEPO and PYRA remained almost constant (94% and 98%, respectively). After loading, the porosity was highest for BC (46%), lowest for CALC (25%) and comparable for TEPO and PYRA (37%). The pore spaces of TEPO and PYRA were highly interconnected in a way that a virtual object with a diameter of 150 µm could access 34% of the TEPO volume and 36% of the PYRA volume. This study shows that a bulk of dense CaP granules in form of tetrapods and pyramids can create a scaffold structure with load capacities suitable for the regeneration of an acetabular bone defect KW - calcium phosphate KW - granules KW - biomechanics KW - bone graft substitutes Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-193233 SN - 1996-1944 VL - 12 IS - 21 ER - TY - JOUR A1 - Ouhaddi, Yassine A1 - Charbonnier, Baptiste A1 - Porge, Juliette A1 - Zhang, Yu-Ling A1 - Garcia, Isadora A1 - Gbureck, Uwe A1 - Grover, Liam A1 - Gilardino, Mirko A1 - Harvey, Edward A1 - Makhoul, Nicholas A1 - Barralet, Jake T1 - Development of neovasculature in axially vascularized calcium phosphate cement scaffolds JF - Journal of Functional Biomaterials N2 - Augmenting the vascular supply to generate new tissues, a crucial aspect in regenerative medicine, has been challenging. Recently, our group showed that calcium phosphate can induce the formation of a functional neo-angiosome without the need for microsurgical arterial anastomosis. This was a preclinical proof of concept for biomaterial-induced luminal sprouting of large-diameter vessels. In this study, we investigated if sprouting was a general response to surgical injury or placement of an inorganic construct around the vessel. Cylindrical biocement scaffolds of differing chemistries were placed around the femoral vein. A contrast agent was used to visualize vessel ingrowth into the scaffolds. Cell populations in the scaffold were mapped using immunohistochemistry. Calcium phosphate scaffolds induced 2.7–3 times greater volume of blood vessels than calcium sulphate or magnesium phosphate scaffolds. Macrophage and vSMC populations were identified that changed spatially and temporally within the scaffold during implantation. NLRP3 inflammasome activation peaked at weeks 2 and 4 and then declined; however, IL-1β expression was sustained over the course of the experiment. IL-8, a promoter of angiogenesis, was also detected, and together, these responses suggest a role of sterile inflammation. Unexpectedly, the effect was distinct from an injury response as a result of surgical placement and also was not simply a foreign body reaction as a result of placing a rigid bioceramic next to a vein, since, while the materials tested had similar microstructures, only the calcium phosphates tested elicited an angiogenic response. This finding then reveals a potential path towards a new strategy for creating better pro-regenerative biomaterials. KW - angiogenesis KW - axial vascularization KW - bioceramic KW - bioinorganic KW - calcium phosphate KW - NLRP3 KW - inflammation Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-304026 SN - 2079-4983 VL - 14 IS - 2 ER -