TY - THES A1 - Müller, Martin T1 - Abstimmbare Halbleiterlaser und schmalbandige Laserarrays mit verteilter lateraler Rückkopplung T1 - tunable semiconductor lasers and narrowband laser arrays with distributed lateral feedback N2 - Im Rahmen dieser Arbeit wurden zwei verschiedene Typen von Halbleiterlasern mit verteilter Rückkopplung (DFB-Laser) entwickelt. Die Laser basieren auf Rippenwellenleitern und verfügen zusätzlich über ein dazu senkrecht orientiertes Metallgitter. Der evaneszente Teil der im Rippenwellenleiter geführten Lichtwelle überlappt mit dem Gitter. Durch diese periodische Variation des effektiven Brechungsindex wird die verteilte Rückkopplung gewährleistet, was eine longitudinal monomodige Laseremission zur Folge hat. Beiden Lasertypen ist gemeinsam, dass der Herstellungsprozess auf einem vom Materialsystem unabhängigen Konzept basiert. Diese Tatsache ist von besonderem Interesse, da so entsprechende Laser für unterschiedlichste Wellenlängenbereiche gefertigt werden können, ohne hierfür neue Herstellungsverfahren zu entwickeln. Den ersten Schwerpunkt der Arbeit bilden Untersuchungen zu sog. abstimmbaren Lasern, deren Emissionswellenlänge innerhalb eines relativ großen Bereichs quasikontinuierlich einstellbar ist. Der Abstimmmechanismus kann mit dem Vernier-Prinzip erklärt werden. Der Laser besteht hierbei aus zwei gekoppelten Segmenten, die jeweils über eine Reihe von Moden (Modenkamm) verfügen. Der Abstand der Moden innerhalb eines Segments ist konstant, wohingegen die Modenabstände der beiden Segmente leicht unterschiedlich sind. Die Emissionswellenlänge des Lasers ist bestimmt durch den Überlapp zweier Moden aus den beiden Segmenten, wobei die Modenkämme so ausgelegt sind, dass gleichzeitig maximal ein Modenpaar überlappt. Eine kleine relative Verschiebung der beiden Modenkämme führt zu einer vergleichsweise großen Verschiebung der Emissionswellenlänge auf Grund des veränderten Überlapps. Die Modenkämme wurden durch spezielle DFB-Gitter, sog. binary superimposed gratings (BSG), realisiert, die, anders als bei konventionellen DFB-Lasern, für mehrere Bragg-Wellenlängen konstruktive Interferenz zulassen und erstmalig bei DFB-Lasern eingesetzt wurden. BSGs zeichnen sich durch sehr gute optische Eigenschaften bei gleichzeitig einfacher Herstellung aus. Zum Abstimmen der Wellenlänge wurde der Brechungsindex des Lasers gezielt durch den Injektionsstrom bzw. die Bauteiltemperatur verändert. Im Rahmen dieser Arbeit konnten abstimmbare Laser auf unterschiedlichen Materialsystemen (InGaAs/GaAs, GaInNAs/GaAs, InGaAsP/InP) hergestellt werden. Der maximale diskrete Abstimmbereich beträgt 38 nm bzw. 8,9 THz und ist durch die Breite des Verstärkungsspektrums limitiert. Quasikontinuierlich konnte ein Abstimmbereich von 15 nm bzw. 3,9 THz erreicht werden. Die typische minimale Seitenmodenunterdrückung (SMSR) beträgt 30 bis 35 dB. Durch Hinzufügen eines dritten Segments ohne Gitter konnte die Ausgangsleistung unabhängig von der Wellenlänge konstant gehalten werden. Den zweiten Schwerpunkt der Arbeit bildet die Entwicklung von DFB-Laser-Arrays mit dem Ziel, longitudinal monomodige Laser mit hoher Ausgangsleistung zu erhalten. Die DFB-Laser-Arrays basieren auf dem oben beschriebenen Prinzip von DFB-Lasern mit lateralem Metallgitter und verfügen über mehrere Rippenwellenleiter, die im lateralen Abstand von wenigen Mikrometern angeordnet sind. Für große Abstände zwischen den einzelnen Lasern des Arrays (Elemente) emittieren diese, weitgehend unabhängig von einander, jeweils longitudinal monomodiges Licht (quasimonochromatische Emission). Die spektrale Breite beträgt hierbei typischerweise 50 bis 70 GHz. Für kleine Elementabstände koppeln die einzelnen Lichtwellen miteinander, was zu einer mit einem konventionellen DFB-Laser vergleichbaren Linienbreite führt. Während die ungekoppelten Arrays über ein gaußförmiges Fernfeld verfügen, ergibt sich für die gekoppelten Arrays ein Interferenzmuster, das stark von verschiedenen Laserparametern (wie z. B. dem Elementabstand) abhängt. Bei InGaAs/GaAs basierenden Arrays (Wellenlänge ca. 980 nm) ergibt sich für DFB-Laser-Arrays mit vier Elementen eine Ausgangsleistung von ca. 200 mW pro Facette, die durch die Wärmeabfuhr begrenzt wird. Trotz der starken thermischen Limitierung (die Laser waren nicht aufgebaut) konnte die 3,5-fache Ausgangsleistung eines Referenzlasers erzielt werden. Bei InGaSb/GaSb basierenden Arrays mit vier Elementen (Wellenlänge ca. 2,0 µm) konnte eine Ausgangsleistung von ca. 30 mW pro Facette erreicht werden, was dem 3,3-fachen eines Referenzlasers entspricht. Die Verwendung von DFB-Laser-Arrays führt folglich zu einer signifikanten Leistungssteigerung, die sich durch geeignete Maßnahmen (Facettenvergütung, Montage, Skalierung) noch weiter erhöhen ließe. N2 - This thesis covers the development of two different types of semiconductor lasers with distributed feedback (DFB). The lasers are based on ridge waveguides and possess an additional metal grating that is oriented perpendicular to the ridge waveguide. The evanescent part of the guided light overlaps with the grating. Due to periodic modulation of the effective refractive index a distributed feedback is accomplished which leads to a longitudinal single mode laser emission. Both lasers have in common, that the manufacturing process is independent of the material system. This fact is of particular interest because one can easily fabricate lasers in different wavelength ranges without having to develop a new manufacturing process. The first part of the thesis covers investigations on tunable lasers. The emission wavelength can be tuned quasi continuous within a relatively large range. The tuning mechanism can be described by the Vernier effect. The laser consists of two coupled cavities, each having a series of well defined modes. The modes are equally spaced within a cavity, whereas the mode spacing between the two cavities is slightly different. The emission wavelength of the device is determined by the overlap of two modes from either cavity. By applying this concept, one can use a relatively small shift of the cavity modes to obtain a rather large shift of the emission wavelength of the laser. The mode spectra have been realized by using so called binary superimposed gratings (BSG). This allows constructive interference for several Bragg wavelengths. BSGs show excellent optical properties as well as an easy fabrication process and have been applied to DFB-lasers for the first time. The wavelength tuning is accomplished by a well directed way of varying the injection currents and the device temperature, respectively. In this thesis, tunable lasers have been demonstrated on a variety of material systems (InGaAs/GaAs, GaInNAs/GaAs, InGaAsP/InP). The maximum discrete tuning range is 38 nm and 8.9 THz, respectively and is limited by the width of the gain spectrum. The maximum quasi continuous tuning range is 15 nm and 3,9 THz, respectively. The typical minimum side mode suppression ratio (SMSR) is 30 to 35 dB. By adding a third segment without any grating, one can keep the output power at a constant level independent of the emission wavelength. The second part of this thesis covers the development of DFB laser arrays resulting in a laser source with high output power and small spectral width. The DFB laser arrays are based on the above described principle of a DFB laser with a lateral metal grating and consists of several parallel ridge waveguides with a lateral distance of a few microns. For a relatively large distance between two adjacent lasers (emitters) the lasers are independent, each emitting single mode light. The total spectral width is around 50 to 70 GHz. Regarding smaller distances between two emitters, light from adjacent lasers interacts which leads to a total spectral width comparable to a conventional DFB laser. Regarding an InGaAs/GaAs based DFB laser array (wavelength around 980 nm), an array with four emitters shows a maximum output power of around 200 mW. Despite the strong thermal limitation (the lasers were not mounted), this is 3.5 times the output power of a reference laser with only one emitter. Regarding the InGaSb/GaAs based DFB laser arrays with four emitters (wavelength around 2.0 µm) the output power is around 3.3 times as high as the output power of a reference device. This shows that the proposed concept of DFB laser arrays with lateral gratings is suitable to improve the output power of a DFB laser and can be further enhanced by means of facet coating, proper mounting and scaling. KW - DFB-Laser KW - Halbleiterlaser KW - DFB-Laser KW - Abstimmbare Laser KW - Laserarray KW - semiconductor lasers KW - dfb-laser KW - tunable laser KW - laser array Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-16922 ER - TY - THES A1 - Krebs, Roland T1 - Herstellung und Charakterisierung von kanten- und vertikalemittierenden (Ga)InAs/Ga(In)As-Quantenpunkt(laser)strukturen T1 - Fabrication and Characterization of edge and vertical emitting (Ga)InAs/Ga(In)As quantum dot (laser) structures N2 - Im Vergleich zu Quantenfilmlasern haben Quantenpunktlaser (unter anderem) die Vorteile, dass kleinere Schwellenströme zu erreichen sind und die Emissionswellenlänge über einen größeren Bereich abgestimmt werden kann, da diese aufgrund der Größenfluktuation im Quantenpunktensemble über ein breites Verstärkungsspektrum verfügen. Ziel des ersten Teils der Arbeit war es, monomodige 1.3 µm Quantenpunktlaser für Telekommunikationsanwendungen herzustellen und deren Eigenschaften zu optimieren. Es wurden sechs Quantenpunktschichten als aktive Zone in Laserstrukturen mit verbreitertem Wellenleiter eingebettet. Eine Messung der optischen Verstärkung einer solchen Laserstruktur mit sechs Quantenpunktschichten ergab einen Wert von 16.6 1/cm (für den Grundzustandsübergang) bei einer Stromdichte von 850 A/cm^2. Dadurch ist Laserbetrieb auf dem Grundzustand bis zu einer Resonatorlänge von 0.8 mm möglich. Für eine Laserstruktur mit sechs asymmetrischen DWELL-Schichten und optimierten Wachstumsparametern ergab sich eine Transparenzstromdichte von etwa 20 A/cm^2 pro Quantenpunktschicht und eine interne Quanteneffizienz von 0.47 bei einer internen Absorption von 1.0 1/cm. Aus den Laserproben wurden außerdem Stegwellenleiterlaser hergestellt. Mit einem 0.8 mm x 4 µm großen Bauteil konnte im gepulsten Betrieb Laseroszillation bis zu einer Rekordtemperatur von 156 °C gezeigt werden. 400 µm x 4 µm große Bauteile mit hochreflektierenden Spiegelvergütungen wiesen im Dauerstrichbetrieb Schwellenströme um 6 mA und externe Quanteneffizienzen an der Frontfacette von 0.23 W/A auf. Für Telekommunikationsanwendungen werden Bauteile benötigt, die lateral und longitudinal monomodig emittieren. Bei kantenemittierenden Lasern kann dies durch das DFB-Prinzip (DFB: distributed feedback) erreicht werden. Im Rahmen dieser Arbeit wurden die weltweit ersten DFB-Laser auf der Basis von 1.3 µm Quantenpunktlaserstrukturen hergestellt. Dazu wurden lateral zu den Stegen durch Elektronenstrahllithographie Metallgitter definiert, die durch Absorption die Modenselektion bewirken. Dank des etwa 100 nm breiten Verstärkungsspektrums der Laserstrukturen konnte eine Verstimmung der Emissionswellenlänge über einen Wellenlängenbereich von 80 nm ohne signifikante Verschlechterung der Bauteildaten erzielt werden. Anhand der 0.8 mm langen Bauteile wurden die weltweit ersten ochfrequenzmessungen an Lasern dieser Art durchgeführt. Für Quantenpunktlaser sind theoretisch aufgrund der hohen differentiellen Verstärkung kleine statische Linienbreiten und ein kleiner Chirp zu erwarten. Dies zeigte sich auch im Experiment. Der zweite Teil der Arbeit befasst sich mit vertikal emittierenden Quantenpunktstrukturen. Ziel dieses Teils der Arbeit war es, Quantenpunkt-VCSEL mit dotierten Spiegeln zunächst im Wellenlängenbereich um 1 µm herzustellen und auf dieser Basis die Realisierbarkeit von 1.3 µm Quantenpunkt-VCSELn zu untersuchen. Zunächst wurden undotierte Mikroresonatorstrukturen für Grundlagenuntersuchungen hergestellt, um die Qualität der Spiegelschichten zu testen und zu optimieren. Diese Strukturen bestanden aus 23.5 Perioden von Spiegelschichten aus AlAs und GaAs im unteren DBR (DBR: Distributed Bragg Reflector), einer lambda-dicken Kavität aus GaAs mit einer Quantenpunktschicht im Zentrum und einem oberen DBR mit 20 Perioden. Es konnten Resonatoren mit sehr hohen Güten über 8000 realisiert werden. Für die weiteren Arbeiten hinsichtlich der Herstellung von Quantenpunkt-VCSEL-Strukturen haben die Untersuchungen an den Mikroresonatorstrukturen gezeigt, dass es an der verwendeten MBE-Anlage möglich ist, qualitativ sehr hochwertige Spiegelstrukturen herzustellen. Aufbauend auf den Ergebnissen, die aus der Herstellung und Charakterisierung der Mikroresonatorstrukturen gewonnen worden waren, wurden nun Quantenpunkt-VCSEL-Strukturen hergestellt. Es wurden Strukturen mit 17.5 Perioden im unteren und 21 Perioden im oberen DBR sowie mit 20.5 Perioden im unteren und 30 Perioden im oberen DBR hergestellt. Erwartungsgemäß zeigten die VCSEL mit der höheren Spiegelanzahl auch die besseren Bauteildaten. Um VCSEL auch im Dauerstrich betreiben zu können, wurden Bauteile mit Oxidapertur hergestellt. Dazu wurden bei 30 µm großen Mesen die beiden Aperturschichten aus AlAs auf beiden Seiten der Kavität zur Strompfadbegrenzung bis auf 6 µm einoxidiert. Es konnte gezeigt werden, dass die Realisierung von Quantenpunkt-VCSELn im Wellenlängenbereich um 1 µm mit komplett dotierten Spiegeln ohne größere Abstriche bei den Bauteildaten möglich ist. Bei der Realisierung von 1.3 µm Quantenpunkt-VCSELn mit dotierten Spiegeln bereitet die im Vergleich zu den Absorptionsverlusten geringe optische Verstärkung Probleme. N2 - In comparison to quantum well lasers, quantum dot lasers provide (among others) the advantages that lower threshold currents are achievable and that the emission wavelength can be tuned over a larger range because the gain spectrum is wider due to the inhomogeneous broadening of the size distribution. The first part of the thesis deals with the theoretical basics and the preliminary investigations which were done before the fabrication of 1.3 µm quantum dot lasers as well as the characteristics of these lasers. The objective of this part of the thesis was the fabrication of single mode 1.3 µm quantum dot lasers for telecommunication applications and the optimization of their properties. Six quantum dot layers were included in the active region of a laser structure with a large optical cavity. The measurement of the optical gain of such a laser structure with six quantum dot layers yielded a value of 16.6 1/cm (for the ground state transition) at a current density of 850 A/cm^2. Thus, laser operation on the ground state is possible down to a cavity length of 0.8 mm. For a laser structure with six asymmetric DWELL layers and optimized growth parameters, a transparency current density of about 20 A/cm^2 per quantum dot layer and an internal quantum efficiency of 0.47 at an internal absorption as low as 1.0 1/cm could be obtained. Based on the laser structures ridge waveguide lasers were processed. With a 0.8 mm x 4 µm large device, laser operation in pulsed mode until 156 °C could be demonstrated. 400 µm x 4 µm large devices with highly reflective mirror coatings operated in continuous wave mode showed threshold currents as low as 6 mA and external quantum efficiencies at the front facet of 0.23 W/A. With these devices continuous wave operation up to 80 °C at an output power above 1 mW is possible. For telecommunication applications devices are needed that show lateral and longitudinal single mode emission. In the case of edge emitting lasers this can be realized with the DFB principle (DFB: distributed feedback). In the scope of this thesis the worldwide first DFB lasers on 1.3 µm quantum dot laser structures were fabricated. During the process, metal gratings lateral to the ridges were defined by electron beam lithography which cause the mode selection by absorption. Due to the 100 nm broad gain spectrum of the laser structures, the emission wavelength could be tuned over a range of about 80 nm without a significant degradation of the device properties. With 0.8 mm long DFB lasers the worldwide first high frequency measurements on lasers of this kind were performed. For quantum dot lasers one theoretically expects a small static linewidth and a small chirp because of the high differential gain. This was confirmed by the experiment. The second part of the thesis deals with vertical cavity surface emitting quantum dot structures. The main objective of this part of the thesis was to fabricate quantum dot VCSELs with doped mirrors in wavelength range around 1 µm and to examine on this basis the realizability of 1.3 µm quantum dot VCSELs. At first, undoped microresonator structures for fundamental studies were fabricated in order to test and to optimize the quality of the mirror layers. These structures consisted of 23.5 periods of AlAs and GaAs mirror layers in the lower DBR (DBR: Distributed Bragg Reflector), a lambda thick GaAs cavity with a single quantum dot layer in the center and an upper DBR with 20 periods. Resonators with high quality factors well above 8000 could be realized. For the further workings concerning the fabrication of quantum dot VCSEL structures the investigations on the microresonator samples have shown that with the MBE system used it is possible to fabricate high quality mirror structures. Based on the results from the fabrication and characterization of the microresonator structures, quantum dot VCSEL structures were fabricated. The VCSEL structures were designed as bottom emitters, which means that they emit from the substrate side. This design permits the epi-side down mounting of the samples on a heat sink. Samples with 17.5 periods in the lower and 21 periods in the upper DBR as well as samples with 20.5 periods in the lower and 30 periods in the upper DBR were fabricated. To be able to operate the VCSELs in continuous wave mode, devices with oxide aperture were processed. For that purpose, on 30 µm pillars both aperture layers consisting of AlAs adjacent to the cavity were oxidized down to a diameter of 6 µm to confine the current path. It could be demonstrated that the realization of quantum dot VCSELs in the 1 µm wavelength range with doped mirrors is possible without having to accept a trade-off as to the device performance. When trying to realize 1.3 µm quantum dot VCSELs with doped mirrors one runs into problems with the optical gain which is rather low as compared to the absorption losses. KW - Drei-Fünf-Halbleiter KW - Halbleiterlaser KW - Halbleiterlaser KW - GaAs KW - Quantenpunkte KW - VCSEL KW - DFB-Laser KW - semiconductor lasers KW - GaAs KW - quantum dots KW - VCSEL KW - DFB laser Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-11328 ER - TY - JOUR A1 - Hopfmann, C. A1 - Albert, F. A1 - Schneider, C. A1 - Höfling, S. A1 - Kamp, M. A1 - Forchel, A. A1 - Kanter, I. A1 - Reizenstein, S. T1 - Nonlinear emission characteristics of quantum dot-micropillar lasers in the presence of polarized optical feedback JF - New Journal of Physics N2 - We report on electrically pumped quantum dot-microlasers in the presence of polarized self-feedback. The high-\(\beta\) microlasers show two orthogonal, linearly polarized emission modes which are coupled via the common gain medium. This coupling is explained in terms of gain competition between the two lasing modes and leads to distinct differences in their input-output characteristics. By applying polarized self-feedback via an external mirror, we are able to control the laser characteristics of the emission modes in terms of the output power, the coherence time and the photon statistics. We find that linearly polarized self-feedback stabilizes the lasing of a given mode, while cross-polarized feedback between the two modes reduces strongly the intensity of the other emission mode showing particular high-intensity fluctuations and even super-thermal values of the photon autocorrelation function \(g^{(2)} (\tau)\) at zero delay. Measurements of \(g^{(2)} (\tau)\) under external feedback also allow us to detect revival peaks associated with the round trip time of the external cavity. Analyzing the damping and shape of the \(g^{(2)} (\tau)\) revival peaks by a phenomenological model provides us insight into the underlying physics such as the effective exciton lifetime and gain characteristics of the quantum dots in the active region of these microlasers. KW - semiconductor lasers KW - coherence KW - system KW - gain Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-123127 SN - 1367-2630 VL - 15 IS - 025030 ER -