TY - THES A1 - Buschmann, Peter T1 - Anbindung von Katalysatoren an Nanodiamantpartikel mit Hilfe starrer Linker T1 - Immobilisation of catalysts on nanodiamond particles using rigid linkers N2 - Das Ziel dieser Arbeit war die Herstellung von Diamantmaterialien, deren Oberflächen mit Alkinen, Aziden oder Aldehyden modifiziert waren. Diese funktionellen Gruppen sollten die einfache Anbindung verschiedener katalytisch aktiver Systeme mit Hilfe der 1,3-dipolaren Cycloaddition nach Huisgen bzw. Iminbildung ermgöglich. Da in einer vorangegangenen Arbeit Hinweise darauf gefunden wurde, dass die hochgradig funktionalisierte Oberfläche von Detonationsnanodiamant dazu in der Lage ist, die Aktivität von immobilisierten Katalysatoren zu behindern. Darum wurde in dieser Arbeit verglichen, ob die Verwendung von starren Linkern auf Tolanbasis einen Vorteil gegenüber ihren flexiblen Gegenstücken liefert. Dazu wurde für jede der oben genannten Funktionalisierungsarten je ein Diamantmaterial mit flexibler sowie mindestens eines mit unbiegsamer Verbindungseinheit hergestellt und getestet. Dadurch konnte das Konzept der starren Linker für Enzyme bestätigt werden und es wurde eine signifikant höhere Aktivität erhalten, als wenn flexible Anbindungsbrücken verwendet wurden. Bei Organokatalysatoren und metallorganischen Systemen konnten jedoch keine erfolgreichen Katalysen durchgeführt werden. N2 - The aim of this work was the production of diamond materials whose surfaces were modified either with alkynes, azides, or aldehydes. These functional groups were supposed to allow the simple immobilisation of catalytically active systems via 1,3-dipolar cycloadditions or imine formation, respectively. In a previous publication, it was found that the highly functionalised surface of detonation nanodiamond can reduce the activity of immobilised catalysts. In this work, it was therefore investigated whether the use of rigid linkers based on tolane derivatives would be advantageous when compared to their flexible counterparts. For this purpose, at least one example for both cases was produced for each of the above mentioned functional groups. Test results showed that the concept of the rigid linkers was successful for the immobilisation of enzymes, for which a significantly higher activity was detected when compared to flexible linkers. However, for organocatalysts and metal organic systems successful catalysis was not achieved. KW - Nanopartikel KW - Diamant KW - Dipolare Cycloaddition KW - Immobilisiertes Enzym KW - Organokatalyse KW - Katalysatorimmobilisierung Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-132966 ER - TY - THES A1 - Grimm, Michael T1 - Aufladungsexperimente an gespeicherten Nanopartikeln mit Synchrotronstrahlung T1 - Charging experiments on trapped nano-particles using synchrotron radiation N2 - Gegenstand dieser Arbeit ist die Untersuchung von gespeicherten Nanopartikeln mit weicher Röntgenstrahlung. Dafür wurde eine neue Apparatur aufgebaut. In dieser befindet sich ein dreidimensionaler elektrodynamischer Quadrupolspeicher, mit dem die positiv geladenen Nanopartikel berührungsfrei und ortsfest gespeichert werden. Mit Hilfe eines Streulichtnachweises werden die Eigenbewegungen der Partikel gemessen und daraus das Ladungs- zu Masseverhältnis ermittelt. Durch gezielte Umladung können die absolute Ladung und die Masse der Partikel mit hoher Genauigkeit bestimmt werden. Die gespeicherten Partikel wurden mit Synchrotronstrahlung am Elektronenspeicherring BESSY II untersucht. Bei niedrig geladenen Partikeln wurden Aufladungsexperimente mit variabler Photonenenergie durchgeführt. Dabei kann die Emission von einzelnen Elektronen beobachtet werden. Die totale Sekundärelektronenausbeute wurde für verschiedene Photonenenergien ermittelt. Sie gleicht den Werten, die durch Messungen mit Elektronenbeschuss bekannt sind. Die Partikel wurden weiterhin bis zum maximal erreichbaren Ladungszustand aufgeladen. Dieser Gleichgewichtszustand liegt unterhalb der theoretischen Erwartungen. Bei den hochgeladenen Partikeln wurden nach Abschalten der Synchrotronstrahlung Entladevorgänge beobachtet, die für das verminderte Ladungsgleichgewicht verantwortlich sind. Die Entladung wird als Ionen-Feldemission interpretiert, möglicherweise hervorgerufen durch den elektrischen Durchschlag im Teilchenmaterial. Das Aufladungsverhalten der Partikel bei verschiedenen Ladungszuständen wurde mit Hilfe von Messungen an der O 1s-Kante untersucht. Bei niedrigen Ladungszuständen liefert der Ladestrom die bekannten Röntgenabsorbtionsstrukturen von Siliziumdioxid. Stark geladene Partikel werden dagegen vor allem im Bereich der resonanten O 1s-Anregung durch schnelle Augerelektronen aufgeladen, während Photoelektronen aus dem O 1s-Kontinuum nicht mehr zur Aufladung beitragen. Deren kinetische Energie ist zu gering, um dem Coulombfeld des Partikels zu entkommen. N2 - Subject of this thesis is the investigation of single trapped nanoparticles using soft X-rays. For this purpose a new apparatus has been developed and characterized. The heart of this apparatus is a three-dimensional electrodynamic quadrupole trap that allows us to store charged nanoparticles well located and without any contact to a substrate. The detection of scattered light, which is modulated by the secular motion frequencies of the stored particle, is used to derive the charge-to-mass ratio. The determination of changes in the charge state due to electron emission is used to determine the absolute charge and mass with high accuracy. The particles were studied using synchrotron radiation at the electron storage ring BESSY II. A set of charging experiments were performed, where particles at low charge state were irradiated with different photon energies in the soft X-ray regime. In these experiments the emission of single electrons is observed. The total secondary-electron emission yield is determined at several photon energies. The values are comparable to the secondary emission after electron impact. Other experiments were performed at highest achievable charge state of the particles. This equilibrium state was found to be far below theoretical predictions. For highly charged particles we found a discharge current after the illumination with synchrotron radiation is terminated. This current is responsible for the low equilibrium charge state. The discharge is assumed to result from ion field emission potentially due to the electric breakdown in the particle material. Charging curves at different charges states of the particle in the regime of the oxygen 1s-edge were recorded. At low charge states the characteristic X-ray absorption fine structure of silicon dioxide is observed. Highly charged particles are efficiently charged by resonant Auger processes in the regime of the resonant O 1s-excitation, whereas there is no charging in the regime of the O 1s-continuum. Evidently, the kinetic energy of these electrons is too small to escape from the attractive Coulomb field of the particle. KW - Nanopartikel KW - Aufladung KW - Synchrotronstrahlung KW - Aufladung KW - Entladung KW - Falle KW - Nanopartikel KW - Synchrotronstrahlung KW - charging KW - discharge KW - trap KW - nano-particle KW - synchrotron radiation Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-13188 ER - TY - THES A1 - Lang, Daniel T1 - Beiträge zur Chemie von Nanodiamantpartikeln – Die 1,3-dipolare Cycloaddition auf modifizierten Diamantoberflächen T1 - Contributions to the Chemistry of Diamond Nanoparticles – The 1,3 dipolar Cycloaddition on modified diamond surfaces N2 - Ausgangspunkt war die aus der Fulleren-Chemie bekannte Prato-Reaktion, bei welcher das Ylid in situ aus einer Aminosäure und einem Aldehyd generiert wird und anschließend mit den C=C-Bindungen des Fullerens reagiert. Diese Funktionalisierungsmethode wurde nun auf Detonationsnanodiamant übertragen. Um zusätzliche π-Bindungen auf der Oberfläche der Diamantteilchen zu schaffen, wurden diese i.Vak. bei 750 °C ausgeheizt (ND750). Für die Immobilisierung wurde die Aminosäure Sarcosin gewählt. Dodecanal und 2,4,6-Tris(hexadecyloxy)-benzaldehyd dienten jeweils als Reaktionspartner. Da bereits in früheren Studien gezeigt wurde, dass bei dieser Reaktion der Aldehyd selbst unspezifisch an den Diamanten binden kann und so möglicherweise Teile der Oberfläche für die spezifische Funktionalisierung blockiert, wurden für die weitere Betrachtung Azomethinylidvorstufen synthetisiert, die selbst nicht in der Lage sind, mit der Diamantoberfläche zu reagieren. Diesen Zweck erfüllten N-heterocyclische Iminiumbromide, die durch Umsetzung des jeweiligen Heteroaromaten mit Bromessigsäureethylester bzw. Bromacetonitril erhalten wurden. Alle Ylidvorstufen wurden in Gegenwart von NEt3 in situ zu den gewünschten Dipolen umgesetzt und auf Nanodiamant immobilisiert. Neben ND750 wurden auch oxidierter und unbehandelter Diamant (NDox bzw. NDunb) sowie Diamant, der bei 900 °C i.Vak. ausgeheizt wurde (ND900), als Substrat eingesetzt, um den Einfluss der Oberflächenterminierung und des Graphitisierungsgrades auf das Reaktionsverhalten zu studieren. Durch Raman- und IR-Spektroskopie wurde gezeigt, dass NDox sehr viele Carbonylgruppen und wenig C=C-Doppelbindungen auf seiner Oberfläche trägt. Durch das Ausheizen i.Vak wurden hingegen zusätzliche π-Bindungen erzeugt, die bei ND900 bereits ausgedehntere Bereiche mit sp2-Kohlenstoff bilden. Der Erfolg der Immobilisierung wurde IR-spektroskopisch nachgewiesen. Die Oberflächenbeladung aller hergestellten Diamantaddukte wurde thermogravimetrisch bestimmt. NDox immobilisierte unabhängig vom Reaktionspartner stets die wenigsten Moleküle auf seiner Oberfläche. Deren Terminierung wird von Carbonylgruppen dominiert, die grundsätzlich schlechtere Dipolarophile darstellen als C=C-Doppelbindungen. Die übrigen Diamantmaterialien NDunb, ND750 und ND900 ließen keine eindeutige Tendenz bezüglich ihrer Reaktionsfreudigkeit erkennen. Die Oberfläche des unbehandelten Diamanten NDunb besitzt sowohl Carbonylfunktionen als auch einzelne Bereiche graphitischen Kohlenstoffs. Diese konkurrieren vermutlich um die angebotenen Dipole, sodass die resultierenden Oberlächenbeladungen ihrer Konjugate in einem mittleren Wertebereich liegen. Durch das Ausheizen i.Vak. werden viele Carbonylgruppen unter Ausbildung weiterer C=C-Doppelbindungen von der Oberfläche entfernt. Bei 750 °C sind diese räumlich sehr beschränkt, stark gekrümmt und daher sehr reaktiv. Trotzdem erreichte ND750 selten eine Oberflächenbelegung, welche jene von NDunb übertrifft. Die π-Bindungen auf seiner Oberfläche sind in Fünf- und Sechsringe eingebaut, um die gekrümmte Struktur zu realisieren. Wahrscheinlich besteht für die Cycloaddition an Nanodiamant eine dem Fulleren C60 ähnliche Regioselektivität bezüglich der angegriffen Doppelbindung. Somit stehen nicht alle frisch erzeugten C=C-Bindungen für die Reaktion zur Verfügung. Bei 900 °C ist die Graphitisierung der Diamantoberfläche weiter fortgeschritten. Es entstehen nicht nur neue C=C-Bindungen, sondern bereits gebildete Kohlenstoffkappen beginnen zu koaleszieren, wobei ausgedehntere sp2-Bereiche mit geringerer Krümmung und somit verminderter Reaktivität entstehen. So nimmt die Oberflächenbeladung der meisten ND900-Konjugate nicht weiter zu. Wie aus den Ergebnissen dieser Arbeit hervorgeht, ist die Funktionalisierung von Nanodiamantpartikeln nicht trivial. Sowohl die Oberflächenbeschaffenheit des Diamantmaterials als auch die Struktur des eingesetzten Azomethinylids beeinflussen das Immobilisierungsverhalten. Die vorliegende Arbeit zeigt aber, dass die 1,3-dipolare Cycloaddition von Azomethinyliden eine nützliche Methode zur Funktionalisierung von Nanodiamantpartikeln ist. Sie ermöglicht des Weiteren die simultane Einführung mehrerer unterschiedlicher funktioneller Gruppen. Dies macht die untersuchte Reaktion zu einem wertvollen Werkzeug für die Herstellung funktionalisierter Nanodiamantmaterialien, z. B. für biomedizinische Anwendungen. N2 - It is commonly known from the chemistry of fullerene C60 that these ylides, generated in situ by a decarboxylative condensation of an amino acid and an aldehyde, add to the C=C double bonds of the fullerene. In this work this kind of functionalization was transferred to nanodiamond particles. Prior to the reaction, the diamond particles were annealed in vacuo at 750 °C in order to establish additional π-bonds on their surface. The amino acid sarcosine was chosen for immobilization. Dodecanal and 2,4,6-tris(hexadecyloxy) benzaldehyde each served as the reactant. Earlier studies demonstrated that the aldehyde itself is able to bind nonspecifically to the diamond surface. Thus, ylide precursors unable to react directly with diamond had to be synthesized. N-heterocyclic iminium bromides served this purpose. They were obtained by the conversion of N-heteroaromatic compounds with bromo ethylacetate and bromo acetonitrile respectively. All ylide precursors were converted in situ to the desired 1,3-dipoles with NEt3 and grafted onto nanodiamond. This reaction was applied not only to ND750, but also to oxidized and pristine diamond (NDox and NDunb) as well as diamond, which was annealed in vacuo at 900 °C (ND900), in order to investigate how the termination and the degree of graphitization of the diamond surface affect the reaction behaviour. As shown by Raman and IR spectroscopy, NDox carries a lot of carbonyl functions and very few C=C bonds. On thermal annealing, additional π-bonds were created, which began to form extended sp2-areas on ND900. The various pre-treated starting materials were subjected to reactions with N-heterocyclic iminium salts. The successful immobilization was verified by IR spectroscopy. The surface loading values of all obtained diamond adducts were determined by thermogravimetric analyses. No matter which reagent was applied, NDox invariably displayed the fewest surface loadings in each course of reactions. This is due to the prevailing carbonyl surface groups. They are essentially poorer dipolarophiles than C=C double bonds. In terms of reactivity the other diamond starting materials NDunb, ND750 and ND900 did not exhibit a definite trend. The surface of the pristine diamond NDunb offers carbonyl groups as well as particular areas of graphitic carbons. They both compete for the applied dipoles and the corresponding diamond conjugates have moderate surface loading values . Annealing the diamond samples in vacuo removes the carbonyl groups and generates further C=C bonds instead. At 750 °C, these are spatially confined, strongly curved and thus highly reactive. Nevertheless, the surface loadings for ND750 rarely exceeded those of NDunb. The π-bonds on its surface are incorporated in five- and six-membered rings to accomplish the curved structure. Regarding the regioselectivity of the attacked double bond, it is possible to compare the cycloaddition on nanodiamond to the reaction on fullerene C60. That is the reason why not all freshly generated C=C bonds on the diamond are available for the reaction. At 900 °C, the graphitization of the diamond surface has further progressed. Not only are new C=C bonds formed, but the already established sp2-caps also begin to coalesce, whereby extended graphitic areas start to emerge. They are less curved and thus less reactive. So the surface loading of most ND900 conjugates does not increase. The experimental findings demonstrate that the functionalization of diamond nanoparticles is not trivial. Both the nature of the diamond surface and the structure of the applied azomethine ylides affect the behaviour of the immobilization. Nonetheless, the herein studied 1,3-dipolar cycloaddition of azomethine ylides is a useful method to functionalize nanodiamonds. It even allows for the simultaneous introduction of several different functional groups. Thus, this dipolar reaction is a valuable tool for the preparation of functionalized diamond nanomaterials, which could be employed for biomedical applications. KW - Azomethinylide KW - Dipolare Cycloaddition KW - Diamant KW - Funktionalisierung KW - nanodiamond KW - functionalization KW - cylcoaddition KW - azomethine ylide KW - Nanopartikel Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-85078 ER - TY - THES A1 - Schweeberg, Sarah T1 - Biomedizinische Anwendung von Nanodiamant: Untersuchungen zu den Wechselwirkungen mit der biologischen Umgebung und zur gezielten Wirkstofffreisetzung T1 - Biomedical applications of nanodiamond: Examinations of the interactions with the biological environment and controlled drug release N2 - Nanodiamant bietet in der Medizin und in der Biologie zahlreiche Anwendungsmöglichkeiten aufgrund der guten Biokompatibilität und geringen Toxizität. Durch die umfangreichen Funktionalisierungsmöglichkeiten der Oberfläche der nanometergroßen Partikel können viele unterschiedliche Wirkstoffe, Rezeptormoleküle oder Peptidsequenzen angebunden werden ,die zusammen mit Nanodiamant ein anderes, durchaus besseres Wirkprofil aufweisen als der Wirkstoff allein. Ziel dieser Arbeit war die Synthese eines pH-labilen Linkersystems, dass hydroxylhaltige Wirkstoffe kovalent bindet und zusammen mit Nanodiamant in die Zelle, in der ein saurer pH-Wert herrscht, eingeschleust werden. Über die Änderung des pH-Wertes in der Zelle soll der Wirkstoff freigesetzt werden und seine Wirkung entfalten können. Weiterhin wurde ein pH-labiles Linkersystem auf der Basis eines Hydrazons hergestellt. Über das synthetisierte Hydrazinderivat können Wirkstoffe, die über eine Aldehyd- oder Ketonfunktion verfügen angebunden werden und pH-labil in der Zelle freigesetzt werden. Zusätzlich trägt der Nanodiamant ein kovalent angebundenes Targeting-Molekül, welches eine verbesserte Adressierung der Wirkorte gewähr¬leisten soll. Die Freisetzung wurde mittels UV-Vis-Spektroskopie detektiert und ausgewertet. Neben der spezifischen Funktionalisierung von Nanodiamant besitzt auch die Interaktion der Nanodiamantpartikel mit biologischen Medien eine besondere Bedeutung für zukünftige biomedizinische Anwendungen. Wenn die Partikeloberfläche durch Proteinadsorption gegenüber dem Wirkort abgeschirmt wird, so kann der angebundene Wirkstoff gegebenenfalls nicht freigesetzt werden und somit nicht seine Wirkung entfalten und bleibt letztlich ungenutzt. So war es von besonderem Interesse die Wechselwirkungen von Nanodiamant in Humanserum und auch weiteren physiologischen Medien zu untersuchen. Dabei wurden sowohl freie Nanodiamantpartikel als auch solche, die auf klinisch bereits eingesetzten Gerüstmaterialien im Bereich der Therapie großer Knochendefekte adsorbiert waren, untersucht. Auch wurden die Wechselwirkungen von Nanodiamant mit der physiologischen Umgebung untersucht, die zur Agglomeration der Nanopartikel führen können. Es wurde ein unter¬schiedliches Agglomerationsverhalten der Nanodiamanten in wässriger Umgebung verglichen mit Nanodiamanten in physiologischen Medien sowie deren Stabilität im Serum beobachtet. Durch die in dieser Arbeit vorgestellten Untersuchungen konnten wichtige Erkenntnisse zur Wechselwirkung verschieden präparierter und funktionalisierter Nanodiamanten mit physiologisch relevanten Umgebungen sowie zu stimuli-responsiven Wirkstofffreisetzung aus Nanodiamant-Konjugaten gewonnen werden. Zudem wurde mit der Untersuchung der angelagerten Proteine um Nanodiamant ein erster Schritt in Richtung eines umfassenden Verständnisses der Wechselwirkung dieses Materials mit biologischen Umgebungen unternommen. Auch wenn diese Wechselwirkungen sehr komplex sind, so sind erste Aussagen bezüglich der Art der angelagerten Proteine möglich. Erste Versuche der Stabilisierung von Nanodiamant in physiologischen Medien wurden ebenfalls erfolgreich durchgeführt und zeigen eine effiziente und einfache Möglichkeit, Nanodiamant in biologischen Medien vor der Agglomeration zu bewahren. Die im Rahmen dieser Arbeit gewonnen Erkenntnisse bezüglich mehrfacher Funktionalisierungsmöglichkeiten von Nanodiamant sowie dessen Stabilisierung in physiologischen Medien zeigen die breite Anwendungsmöglichkeit und das enorme Potential von Nanodiamant im Bereich medizinischer und biologischer Anwendungen auf. N2 - Nanodiamond offers various possible applications in medicine and biology because of its good biocompatibility and low toxicity. Due to the extensive opportunities functionalizing the surface of the nanosized particles it is possible to bind a lot of different active pharmaceutical ingredients (API), receptor molecules or peptide sequences. This functionalization can result in an improved efficacy compared to the profile of the drug alone. The aim of this thesis was the synthesis of a pH-labile linkersystem which covalently binds hydroxyl group-containing APIs and transfer them together with nanodiamond into the cells, where an acidic environment is predominant. Because of the change of the pH-value the drug gets released and can take its effect. Furthermore, a pH-labile linkersystem based on the formation of a hydrazon bond was synthesized. APIs containing an aldehyde or a ketone can be linked to the synthesized hydrazine derivative 70 and be released in cells due to the acid-labile bond. Additionally, the nanodiamond has a covalently bound targeting molecule to assure an improved uptake into the cell. The release of Doxorubicin was detected and evaluated via UV-Vis-spectroscopy. Besides the specific functionalization, the interaction of nanodiamond particles with biological media is gaining more and more importance regarding future biomedical applications. If the particle surface is shielded with proteins it is possible that the linked drug cannot be released, remains unused and cannot develop its desired effect. Because of this reason it was of main interest to examine the interactions of nanodiamond in human serum and further physiological media. Nanodiamond without further functionalization were analysed as well as nanodiamonds which are adsorbed on materials that are already in clinical usage in the field of greater bone defects. The interactions of nanodiamond with a physiological environment which can lead to the agglomeration of the particles was also examined. A different agglomeration bahaviour of nanodiamond in aqueous media was compared to nanodiamond in physiological media as well as their stability in serum. Due to the presented studies in this thesis important insights into the interactions of functionalized and different prepared nanodiamonds with physiological relevant environments as well as with stimuli-responsive drug release from nanodiamond conjugates were obtained. Furthermore, the examinations of the attached proteins around nanodiamond is the first step getting towards a better comprehensive understanding of the interactions of this material with its biological environment. Even if these interactions are very complex, first statements according to the type of attached proteins are possible. First trials of stabilizing nanodiamond in physiological media have been carried out successfully and demonstrate an easy and effective way to hinder agglomeration of nanodiamond in biological media. Finally, the insights gained in this thesis regarding the multiple possibilities of nanodiamond as well as their stabilization in physiological media offers a broad range of applications and the tremendous potential of nanodiamond in the field of medical and biological research. KW - Nanopartikel KW - nanodiamond KW - Wirkstofffreisetzung KW - drug release KW - Diamant KW - Wirkstofffreisetzung KW - Nanodiamant Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-174619 ER - TY - THES A1 - Liang, Yuejiang T1 - Deagglomerierung und Oberflächenfunktionalisierung von Nanodiamant mittels thermochemischer und mechanochemischer Methoden T1 - Deagglomeration and surface modification of nanodiamond via thermochemical and mechanochemical method N2 - Nanodiamant weist aufgrund seiner herausragenden mechanischen, optischen und biokompatiblen Eigenschaften ein enormes Potential auf. Für eine erfolgreiche Anwendung muss dieser jedoch zunächst desagglomerisiert und an seiner Oberfläche funktionalisiert werden. In dieser Arbeit werden zwei unterschiedlichen Methoden zur Deagglomerierung und Oberflächenfunktionalisierung vorgestellt. Im ersten Teil wird die thermochemische Methode beschrieben, um den ungewöhnlich stark agglomerierten Detonationsnanodiamant zu deagglomerieren. Dabei wird die Strategie verfolgt, den Nanodiamant erst durch eine thermische Behandlung im Vakuum die vorhandenen Oberflächengruppe zu entfernen, π-Bindungen zu etablieren und dann dessen Oberfläche durch kovalente Bindungen zu modifizieren. Im zweiten Teil wird eine mechanochemische Methode für die Deagglomerierung und Oberflächenfunktionalisierung vorgestellt. Dabei wird ein völlig neuer Ansatz (BASD-Verfahren) entwickelt. Die Ultraschallbehandlung in Kombination mit zusätzlichen Mikrokeramikpartikeln eignet sich hervorragend, um Nanodiamant-agglomerate aufzubrechen. Zwei unterschiedliche Reaktionen mit zwei unterschiedlichen Nanodiamantsorten werden getestet: Eine einfache Kondensationsreaktion durch Silanisierung und eine Radikalreaktion über das Diazoniumsalz. In weiteren Experimenten kann gezeigt werden, dass sich die zuerst vorgestellte thermochemische Methode auch eignet, um aus fluoreszierenden NV-Nanodiamant kolloidalen NV-Nanodiamant mit funktionellen Gruppen herzustellen. Der letzte Teil der vorliegenden Arbeit beschäftigt sich mit der Herstellung von Nanodiamanten aus Diamantfilmen mit Hilfe des Top-down Ansatzes, da der gezielte und kontrollierte Aufbau der Gitterstruktur des Diamanten sowie die kontrollierte Einführung bisher nur durch CVD oder Ionenimplantationstechnik möglich ist. N2 - Nanodiamond exhibits an enormous potential due to its outstanding mechanical, optical and biocompatible properties. However, a successful application must begin with deagglomerated and functionalized particles. In this study, two different methods for deagglomeration and surface functionalization are introduced. The first part deals with a thermochemical method for deagglomeration of unusual tight agglomerated detonation nanodiamond. Thereby, a new strategy is developed, in which the nanodiamond is partially graphitized by annealing in vacuum in order to remove the present surface groups and establish π-Bonds, followed by surface-modification through covalent grafting. In the second part, a mechanochemical method for the deagglomeration and surface functionalization is presented. A completely new approach (BASD method) is developed. Ultrasonic treatment in combination with additional micro-ceramic particles is excellently suited for breaking up agglomerates of nanodiamond.Two different reactions with two different types of nanodiamond are tested: A simple condensation reaction by silanization and a radical reaction of the diazonium salt. Further experiments show that the first presented thermochemical method is also suitable for production of colloidal nanodiamond with functional groups from fluorescent NV-nanodiamond. In the last part of the present work, the production of nanodiamonds from diamond films by means of a top-down approach is described. So far, only the CVD production of diamond enables a direct access to a structured diamond material. KW - Nanopartikel KW - Synthesediamant KW - Aggregat KW - Funktionalisierung KW - Kolloid KW - Nanodiamant KW - Deagglomerierung KW - nanodiamond KW - deagglmeration KW - surface functionalisation Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-56296 ER - TY - THES A1 - Kröker, Kristin T1 - DNA-Kohlenstoffnanorohr-Konjugate - Biokompatibilität, ex vivo-Verhalten, Funktionalisierung T1 - DNA-carbon nanotube conjugates - biocompatibility, ex vivo behavior, funtionalization N2 - Einzelstrang-DNA-dispergierte und individualisierte (6,5)-chirale Kohlenstoffnanoröhren bilden als Konjugatsystem den Ausgangspunkt dieser Dissertation. Im Vordergrund stehen dabei Untersuchungen zur Biokompatibilität dieser ssDNA-SWNT-Konjugate sowie deren Verhalten nach Zellpenetration und eine Funktionalisierbarkeit zum Wirkstofftransportsystem. Das erste Projekt widmet sich in Kapitel 4 dem Studium der Konjugatstabilität unter physiologischen Bedingungen und einer Verträglichkeit gegenüber zellulären Systemen. Experimente zur Biokompatibilität werden erstmals an Nanorohrkonjugaten durchgeführt, welche nach Ultrazentrifugation im Dichtegradienten sorgfältig individualisiert vorliegen. Die umgebungssensitiven photophysikalischen Charakteristika vereinzelter (6,5)-SWNTs können zu einer Beurteilung der Konjugatintegrität in physiologischem Milieu genutzt werden. Die Stabilität von ssDNA-SWNT-Strukturen wird in Anwesenheit des Restriktionsenzyms DNase I und dem in Zellnährmedien enthaltenen protein- und nukleasereichem Serum FBS auf die Probe gestellt. In beiden Fällen kann eine ausreichende ssDNA-SWNT-Integrität attestiert werden, die eine Verwendung unter Zellkultivierungsbedingungen erlaubt. Unter Berücksichtigung verschiedener in Zellen vorliegender pH-Umgebungen werden die Konjugate ebenfalls dieser Variation ausgesetzt. Bei Vorliegen stark saurer und basischer pH-Werte kann die Integrität von ssDNA-SWNT-Konjugaten nicht gewährleistet werden, was sich durch Aggregation bemerkbar macht. Innerhalb des breiten pH-Bereichs zwischen den Werten 3 und 11 hingegen kann eine gute Stabilität bestätigt werden. Für zelluläre Anwendungen bedeutet dieser Befund keine Einschränkung, da in Kulturen lediglich neutrale bis schwach saure pH-Werte oberhalb von 4.5 zu finden sind. Nachdem die Biostabilität der ssDNA-SWNT-Konjugate gewährleistet ist, kann in Zytotoxizitätsstudien eine ex vivo-Verträglichkeit des Nanomaterials getestet werden. Erste Untersuchungen mit der Mausmakrophagenlinie J774.1 weisen wie auch ausführliche Studien gegenüber menschlichen Epithelzellen HeLa auf eine uneingeschränkte Kompatibilität in den eingesetzten Konzentrationen hin. HeLa-Zellen, die mit DGU-gereinigten Nanorohrproben behandelt werden, zeigen eine geringfügig höhere Vitalität als nach Inkubation mit einer Rohdispersion undefinierter SWNT-Bündel. Im Gesamtbild ergibt sich somit eine zufriedenstellende Biokompatibilität individualisierter ssDNA-SWNT-Konjugate, womit das in dieser Arbeit zentrale Kohlenstoffnanorohrsystem den Anforderungen für dessen biomedizinische Verwendbarkeit gerecht wird. Der Schwerpunkt weiterer Untersuchungen liegt im zweiten Projekt aus Kapitel 5 auf dem Verhalten von ssDNA-SWNT-Konjugaten nach deren Aufnahme in HeLa-Zellen. Auch hier kann die starke Sensitivität der optischen Eigenschaften individualisierter (6,5)-Kohlenstoffnanoröhren gegenüber Umgebungseinflüssen genutzt werden, um Veränderungen im Emissionsverhalten von SWNTs nach deren zellulärer Aufnahme gegenüber dem Ausgangszustand zu beobachten. Nach ausführlicher Weißlicht-, Fluoreszenz- und SWNT-Photolumineszenzmikroskopie, aus deren Resultaten eine erfolgreiche Internalisierung von ssDNA-SWNTs in HeLa-Zellen eindeutig hervorgeht, stehen PL-spektroskopische Untersuchungen der Kohlenstoffnanoröhren im Vordergrund. Durch einen Vergleich des Emissionsverhaltens der ssDNA-SWNT-Konjugate in und außerhalb von Zellen können spektrale Verschiebungen, Linienverbreiterungen und verkürzte Fluoreszenzlebensdauern nach zellulärer Aufnahme festgestellt werden. Sowohl eine Aggregation von SWNTs als auch eine Beeinflussung durch die pH-Umgebung reichen nicht für eine vollständige Erklärung des Befunds aus. Vielmehr kann die in endosomalen Kompartimenten durch das Größenverhältnis von Endosomen zu SWNTs entstehende räumliche Nähe einer großen Nanorohrmenge untereinander als Ursache für eine Veränderung der dielektrischen Umgebung und folglich des Emissionsverhaltens betrachtet werden. Durch Verwendung der Kohlenstoffnanoröhren als Marker und Sensor können ssDNA-SWNT-Konjugate in Zellen somit nicht nur lokalisiert, sondern darüber hinaus hinsichtlich einer möglichen Aggregation untersucht werden. Aus den in dieser Arbeit vorgestellten Daten kann zwar eine vollständige Aggregation der SWNTs durch deren Aufnahme in Zellen ausgeschlossen werden, sie muss jedoch in geringfügigem Ausmaß neben einer Beeinflussung durch die pH-Umgebung und die große räumliche Nähe durchaus in Betracht gezogen werden. Individualisierte ssDNA-SWNT-Konjugate können damit erstmals zeitaufgelöst PL-mikrospektroskopisch in HeLa-Zellen charakterisiert werden. Für das letzte Projekt werden in Kapitel 6 neuartige Funktionalisierungsmöglichkeiten von ssDNA-SWNT-Konjugaten zu zellulären Transportsystemen unter Erhalt der photophysikalischen Eigenschaften erforscht. Dazu soll das Dispergiermittel DNA als Kupplungsstelle für eine kovalente Anbindung eines Agenz genutzt werden. Anstelle eines Wirkstoffes werden die Untersuchungen mit einem Fluorophor als Modellverbindung durchgeführt, welcher den Vorteil einer einfachen Detektierbarkeit liefert. Prinzipiell besteht die Möglichkeit, das Oligomer mit dem Fluorophor vorzufunktionalisieren und anschließend auf die Oberfläche der SWNTs zu bringen. Als effektiver erweist sich die Methode der direkten Kupplung des Farbstoffs an bereits DNA-dispergierte SWNTs. Der Erfolg in der Präparation von FluorophorssDNA- SWNT-Konjugaten wird über die Emission des Fluorophors mit entsprechenden Referenzexperimenten gemessen. Der Versuch einer Quantifizierung liefert jedoch sehr hohe Werte, die lediglich als eine obere Grenze für die gefundene Anzahl gebundener Fluorophore pro Nanoröhre angesehen werden können. Im Verlauf des Projekts kann eine Funktionalisierbarkeit der Nanoröhren über das Dispergieradditiv DNA als neue Strategie aufgezeigt werden. Im Gegensatz zu bekannten Wirkstofftransportsystemen bietet dieser Funktionalisierungsansatz den Vorteil, dass die optischen Eigenschaften der individualisierten ssDNA-SWNT-Konjugate erhalten bleiben, welche wieder um einen gleichzeitigen Einsatz der Nanoröhren als Transporter und Marker bzw. Sensor erlauben. Die vorliegende Dissertation liefert neben dieser bisher unbekannten Funktionalisierungsstrategie neue Erkenntnisse über die Biokompatibilität speziell von individualisierten ssDNA-SWNT-Konjugaten und deren Verhalten in HeLa-Zellen. Mit diesem Wissen kann der gezielte Wirkstofftransport durch Kohlenstoffnanoröhren als biokompatibles und zellgängiges Trägersystem anvisiert werden. N2 - The key element of this thesis is a conjugate system of single-stranded DNA and individualized (6,5) single-wall carbon nanotubes. The investigations are mainly focused on the biocompatibility of ssDNA-SWNT conjugates, as well as their behavior after cell penetration and general ability to be functionalized for drug delivery. Within the first project, chapter 4 contributes to the study the conjugate stability under physiological conditions and compatibility towards cellular structures. For the first time, such biocompatibility experiments are carried out with nanotube conjugates, which are thoroughly individualized by ultracentrifugation assisted density gradient. The photophysical characteristics of isolated (6,5) SWNTs are highly sensitive towards their environment and can thus be used to evaluate the state of conjugate integrity in a physiological milieu. The stability of ssDNA-SWNT structures is tested in the presence of restriction enzyme DNase I and FBS serum, an important nutrient medium ingredient rich in proteins and nucleases. In either case, the integrity of ssDNA-SWNT conjugates is not affected. With respect to the pH variety occuring in cell structures, the conjugate stability is also investigated in acid and base milieu. Both strong acid and alkaline pH environments influence the integrity of ssDNA-SWNT, leading to aggregation of nanotubes. Conversely, good conjugate stability can be evaluated in a wide pH range between 3 and 11, revealing unlimited applicability towards cells, where the pH environment is known to vary between neutral and weakly acid pH values above 4.5. After evaluation of the biostability of ssDNA-SWNT conjugates, they have to be tested in ex vivo cytotoxicity assays. Studies are primarily carried out with murine macrophage-like cells J774.1 and in more detail with the human cervix carcinoma cell line HeLa. Both indicate no cytotoxic effects with applied SWNT concentrations. Within the HeLa cell studies, the impact of DGU preparation on SWNT cytotoxicity is a further point of interest. As a result, slightly enhanced cell viability can be observed with DGU purified samples as compared to raw dispersion consisting of non-defined SWNT bundles. Overall, ssDNA-SWNT conjugates can be assumed to be sufficiently biostable and thus suitable for biomedical applications. Further investigations in the second part of this work in chapter 5 are focused on the behavior of ssDNA-SWNT conjugates after cellular uptake. Again, the strong environmental sensitivity of optical properties of individualized (6,5) carbon nanotubes can be used to detect changes of the SWNT emission after internalization. Different techniques have been employed to visualize ssDNA-SWNT structures in HeLa cells using white light, fluorescence, and SWNT photoluminescence microscopy. By PL spectroscopy of ssDNA-SWNTs in cells spectral shifts, line-broadening and shortened lifetimes are observed when comparing SWNT emission inside and outside of cell culture. Neither nanotube aggregation nor the influence of the cell-specific pH environment are sufficient explanations for such spectral behavior. Indeed, the spatial proximity of SWNTs with each other in small sized endosomal cell compartiments is supposed to cause nanotube-nanotube interactions that change the dielectric environment and thus the emission behavior of SWNTs. Within the use of carbon nanotubes as marker and sensor, ssDNA-SWNT conjugates cannot only be localized, but also characterized, with regard to possible nanotube aggregation. The data presented in this work can, on the one hand, exclude a total aggregation of SWNTs within their cellular uptake. But, on the other hand, a small extent of aggregation, pH environmental effects, and the spatial proximity of a high amount of SWNTs in comparatively small endosomes have to be considered as factors that influence SWNT emission properties. In this study, individualized ssDNA-SWNT conjugates can be characterized via time-resolved PL microspectroscopy for the first time. The last project in chapter 6 addresses to new functionalization routes of ssDNA-SWNT conjugate with respect to drug delivery applications while retaining the photophysical characteristics. The SWNT dispersion additive DNA serves as binding site for covalent attachment of agents. For a convenient sample characterization, a fluorophor is used as model compound instead of a specific drug. In general, fluorophor-ssDNA-SWNT systems can be obtained by pre-functionalization of oligomers with dye, followed by attachment of the modified DNA on the nanotube surface. More promising, however, is the route via a direct coupling reaction of activated fluorophor molecules with specific ssDNA-SWNT conjugates. The successful sample functionalization can be evaluated from the fluorescence of the dye in comparision with corresponding control experiments. An attempt for quantification of functionalization is found to be problematic as the revealed values are too high and can thus only be regarded as upper limits for the number of fluorophors per nanotube. A new functionalization method for SWNTs can be established using noncovalently bound DNA as the coupling point. Compared to well-known drug delivery systems, the optical properties of SWNTs can be retained with this procedure, allowing the simultaneous use of nanotubes as cellular transporter and marker or sensor. In addition to the new functionalization strategy, further knowledge about biocompatibility of well-isolated ssDNA-SWNT conjugates and their behavior after cellular uptake can be obtained through this thesis. Thus, a targeted drug delivery with isolated carbon nanotubes as biocompatible and a cell penetrating carrier system could be aimed for future work. KW - Biokompatibilität KW - DNS KW - Nanopartikel KW - Funktionalisierung KW - HeLa-Zelle KW - NIR-Spektroskopie KW - Photolumineszenz KW - Kohlenstoffnanoröhre KW - Dichtegradientenultrazentrifugation KW - carbon nanotube KW - density gradient ultracentrifugation Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-74552 ER - TY - THES A1 - Niederdraenk, Franziska T1 - Ensemble-Modellierung von Röntgenbeugungsdaten zur Strukturbestimmung von Nanopartikeln T1 - Ensemble modeling of X-ray diffraction data for the geometric structure determination of nanoparticles N2 - Ziel dieser Arbeit war es, die geometrische Struktur von Nanopartikeln mittels Pulver-Röntgenbeugung und einem neuen Analyse-Verfahren, der Ensemble-Modellierung (EM), zu ermitteln. Die genaue Aufklärung der kristallinen Struktur ist ein Schlüssel für die Entwicklung exakter theoretischer Modelle und damit für ein besseres Verständnis der Nanoteilchen und deren Eigenschaften. Dabei fußt die Methode auf einem atomaren Modell und berechnet daraus das Beugungsbild der Teilchen. Neben der Auswertung verschiedener Proben sollte ebenso das Potential der Methode überprüft werden - auch im Vergleich zu Standardmethoden wie der Rietveld-Verfeinerung oder einer Einzellinien-Anpassung. Im Gegensatz zur EM beinhalten letztere kein explizites Nanoteilchenmodell. Insgesamt kamen drei typische Nanopartikel-Systeme zum Einsatz: Zunächst wurden fünf ZnO-Proben untersucht, die aufgrund ihrer verschiedenen Liganden deutlich unterschiedliche Partikelgrößen zeigten. Die präsentierten CdS-Nanoteilchen bildeten dagegen mit unter 100 Atomen bereits den Übergang zur Clusterphysik. Das letzte Kapitel stellte schließlich drei Proben mit deutlich komplexeren Core-Shell-Partikeln vor, welche aus einem CdSe-Kern und einer ZnS-Schale bestehen. Dabei konnten mit Hilfe der EM für alle Systeme sehr viel detailliertere Aussagen gemacht werden, als mit den Standardmethoden. Anhand der ersten vorgestellten ZnO-Probe wurde gezeigt, wie man sich bei der Auswertung mit der EM schrittweise dem besten Modell nähert, indem man, startend mit der Partikelform, anschließend weitere komplexe Merkmale implementiert. In dem ZnO-Kapitel wurde ersichtlich, dass die Liganden eine große Rolle spielen - nicht nur für die Größe der Nanopartikel, sondern auch für deren Qualität. Weiterhin wurde festgestellt, dass der Ligand TG beinahe defektfreie Nanoteilchen liefert, während die Stabilisatoren DACH und DMPDA den Einbau von Stapelfehlern begünstigen. In den jeweiligen Vergleichen mit der Rietveld- und Einzellinien-Anpassung fiel auf, dass diese Methoden für kleine Nanoteilchen Resultate liefern, die als deutlich weniger vertrauenswürdig einzustufen sind als jene, die mit der EM erhalten wurden. Der Grund sind die für kleine Teilchen nicht vernachlässigbaren Faktoren wie eine (anisotrope) Form, Oberflächeneffekte, Parameter-Verteilungen etc., welche nur mit der EM berücksichtigt werden können. Noch ungenauer fällt die Analyse per Absorptionsspektroskopie plus theoretischen Methoden aus. Die einzige CdS-Probe wies mit ca. 1.3 nm Durchmesser besonders kleine Nanoteilchen auf. Das zugehörige Beugungsbild zeigte daher nur noch sehr wenige Strukturen, was bereits die Bestimmung der Kristallstruktur erschwerte. Bei nur noch einigen gestapelten Schichten verloren auch die Stapelfehler ihre ursprüngliche Bedeutung. Die maßgebliche Frage bestand somit darin, ob man bei Kristalliten mit unter 100 Atomen noch von einer "normalen" Kristallstruktur sprechen kann, oder ob hier bereits andere Strukturformen vorliegen, z.B. ähnlich den C60-Molekülen. Da die EM solche Hohl-Strukturen ebenfalls simulieren kann, wäre der nächste Schritt, diese für sehr kleine Partikel im Vergleich zu den üblichen Kristallstrukturen zu testen. Bei den drei betrachteten Core-Shell-Proben zeigte die EM abermals ihre große Stärke, indem sie es ermöglichte, die deutlich komplexeren Teilchen realistisch zu simulieren. So war es möglich, die experimentellen Röntgenbeugungs-Daten hervorragend wiederzugeben, was mit keiner der Standardmethoden gelang. Hierfür war es nötig, neben dem CdSe-Kern eine zusätzliche ZnS-Schalenstruktur einzuführen. Zwar konnte bei den Proben mit der EM alleine nicht eindeutig festgestellt werden, welcher ZnS-Schalentypus vorliegt, es wurden jedoch diverse Anhaltspunkte gefunden, die für ein lokal-epitaktisches Wachstum auf dem CdSe-Kern sprechen. Für die Methode der EM selbst lässt sich in der Retrospektive folgendes fest halten: Sie ist den Standard-Techniken wie der Rietveld-Verfeinerung für sehr kleine Nanopartikel deutlich überlegen. Der Grund dafür sind die vielfältig modellierbaren Strukturen, welche Defekte, Oberflächeneffekte, Parameterverteilungen etc. beinhalten können. Ein weiterer großer Pluspunkt der EM gegenüber anderen Methoden besteht in der Möglichkeit, die immer populärer werdenden Core-Shell-Partikel mit vielfältigen Schalenarten zu simulieren, wobei hier auch noch weitere komplexere Optionen für Schalen, z.B. zweierlei Schalen (Core-Shell-Shell-Teilchen), vorstellbar sind. Die Tatsache, dass all diese Merkmale zudem intrinsisch in dem berechneten Beugungsbild enthalten sind, ist von besonderem Gewicht, da dies bedeutet, keine künstlichen Parameter einführen und diese interpretieren zu müssen. Solange eine gewisse Atomanzahl pro Partikel nicht überschritten wird, und v.a. bei defektbehafteten Nanoteilchen, stellt die EM somit die erste Wahl dar. N2 - The goal of this thesis was to determine the geometric structure of very small nanoparticles by means of powder x-ray diffraction and a novel analysis method called Ensemble Modeling (EM). The knowledge of the crystalline structure is a key feature to develop new theoretical models and thus to better understand the particles' properties. The analysis method itself is based on an atomic model of the particles, which is used to calculate the diffraction pattern via the Debye formula. Apart from the investigation of several nanoparticle samples, the capability of the new technique was tested - especially in comparison to commonly used standard methods like the Rietveld refinement or single-line fits. In contrast to the EM, these methods do not contain a real model of the particles. Altogether, three characteristic nanoparticle systems were used: First of all, five ZnO samples were investigated, which showed different particle sizes (2-15 nm) due to the use of different stabilizing molecules. In contrast, the CdS particles presented here had a diameter of only 1.3 nm, which is already at the transition to cluster physics. The last chapter introduced three samples of the more complex core-shell-nanoparticles, which, in this case, consisted of a CdSe core and a ZnS shell. By applying the EM as analysis method, all particle systems could be investigated in much more detail than with other analysis methods. The first ZnO sample served as an example to explain the stepwise procedure of the EM. After the particle shape was determined, more and more complex features were implemented in order to eventually arrive at the atomic model best reproducing the real particle ensemble. In case of the ZnO samples it was shown that the ligands play a significant role - not only for the size of the particles but also for their structural quality. A further finding due to the analysis with the EM is the high amount of stacking faults for particles stabilized with the ligands DACH or DMPDA, while TG favors a defect-free growth of ZnO nanoparticles. In comparison to the Rietveld method or to a single-line fit, the results for small nanoparticles given by the EM are much more reliable, since none of the other fitting methods can take features like the (anisotropic) particle shape, surface effects or parameter distributions into account. The same holds for a particles' size analysis via UV/Vis absorption spectroscopy together with theoretical models. The EM, in contrast, can account for all of these sophisticated structural features. The only CdS sample in this work contained extremely small particles of about 1.3 nm in diameter. The according diffraction pattern thus shows very broad reflections and little usable structure, thereby hindering a straight-forward analysis. Since the CdS particles consisted of only a few stacked layers, even the concept of stacking faults looses its meaning. The question arises, whether the term "crystal structure" is still appropriate for a particle with less than 100 Atoms. For instance, it would be possible that the particles form hollow structures similar to the C60 molecules. Since these structures can be simulated with the EM as well, this could be one next step to further analyse the XRD data of the CdS sample. The last chapter of this thesis introduced three samples of core-shell-nanoparticles, each with a CdSe core and a ZnS shell. Here again, the power of the EM method was demonstrated by forming a realistic model of these much complexer particles. The calculated diffraction patterns reproduced the experimental data very well - in contrast to all other analysis methods. The success of the EM was due to the implementation of an additional ZnS structure in the simulated model. Even if the shell type of this additional structure could not clearly be identified by XRD and our analysis, there is some strong evidence for a local epitaxy of the ZnS on the CdSe core. In conclusion, it was demonstrated that the EM method is far superior to any of the standard techniques for the diffraction pattern analysis of small nanoparticles. The particular strengths of the EM are the manifold structures, which can be simulated, together with defects, surface effects, parameter distributions etc. A further advantage over the other analysis methods is the possibility to form realistic core-shell-particles with a diversity of shell types. Even more complex shells are conceivable, e.g. a mixed shell or the double shell of the core-shell-shell-particles. All these features are intrinsically included in the models and thus in the diffraction patterns, i.e., no artificial parameters must be introduced and later be interpreted. As long as a certain amount of atoms per particle is not exceeded, and, especially for particles containing many defects, the EM introduced here should thus be preferred. KW - Nanopartikel KW - Röntgenstrukturanalyse KW - Ensemble-Modellierung KW - Core-shell Nanoteilchen KW - CdSe/ZnS Nanoteilchen KW - Strukturbestimmung KW - Röntgenbeugung KW - Zinkoxid KW - Cadmiumselenid KW - XRD KW - structure determination KW - nanoparticles KW - ensemble modeling Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-52218 ER - TY - THES A1 - Seidenspinner, Amelie Maria T1 - Entwicklung einer biofunktionalen Beschichtung für mit Silber dotierte Titandioxid-Nanopartikel T1 - Development of a biofunctional coating for silver doped titanium dioxide nanoparticles as potential anticancer agents N2 - Ziel dieser Arbeit war es, eine erfolgreiche Beschichtung der verschiedenen TiO2 Nanopartikel mit aufsteigendem Silberanteil herzustellen, um eine ausgeprägte Stabilisierung und Biokompatibilität der Partikel zu erreichen. Anschließend wurde ihre Wirkung gegenüber gesunden Zellen und Tumorzellen anhand von Zellversuchen untersucht. Zunächst mussten die TiO2 Aggregate nach ihrer Redispergierung in Wasser, Toluol oder Tris Base gespalten werden, damit anschließend eine kontrollierte Beschichtung einzelner Nanopartikel durchgeführt werden konnte. Der Einfluss von Ultraschall in Form einer zweiminütigen Ultraschalltipbehandlung lieferte hierbei die niedrigsten Partikelgrößen in der DLS-Messung. Die Beschichtungen wurden mit APTES, Dopamin und PEG-SH unter Einfluss von unterschiedlichen Ultraschalltipzeiten, Konzentrationen, Temperaturen, pH-Werten, Salzen sowie verschiedenen Magnetrührtechniken und Waschprozessen entwickelt. Durch die Charakterisierungsmethoden via dynamischer Lichtstreuung, Zetapotentialmessung, Infrarotspektroskopie, REM und STEM wurde jede Beschichtung analysiert und auf diese Weise ihre optimale Herstellungsmethode erarbeitet. Schlussendlich wurde der Einfluss unbeschichteter sowie mit APTES, PDA und PEG-SH beschichteter TiO2 Nanopartikel mit steigendem Silberanteil anhand gesunder Zellen und Tumorzellen in vitro untersucht. Die Zellen wurden für 24 h mit den Partikeln inkubiert und anschließend mittels Durchflusszytometrie charakterisiert. Generell wurde nur eine geringfügige Auswirkung der Partikel auf die Zellen beobachtet. Die in der Literatur beworbene Aussage, dass silberdotierte TiO2 in der Lage sind, entartete Zellen zu töten, während gesunde Zellen ausgespart werden, konnte nicht bestätigt werden. Dennoch besaßen einige Faktoren einen Einfluss auf die Vitalität und Zellzahl. So spielte der steigende Silberanteil bei den Zellen eine Rolle, die einen Effekt auf die TiO2 Nanopartikel zeigten. Mit steigendem Ag-Anteil sanken Zellzahl und Vitalität stärker. Auch eine ansteigende Konzentration der beschichteten Partikel wirkte sich positiv auf das Absinken der Zellzahl aus. Besonders die adhärent wachsende Tumorzelllinie Panc02 zeigte sich sensibel gegenüber den beschichteten und unbeschichteten Partikeln. Die Beschichtung, welche die größte Auswirkung auf die Zellzahl- und Vitalitätsminderung der Zellen hatte, war eindeutig die PDA-Beschichtung. N2 - The aim of this work was to produce a successful coating of the various TiO2 nanoparticles with an increasing proportion of silver in order to achieve a pronounced stabilization and biocompatibility of the particles. Subsequently, their effects on healthy cells and tumor cells were examined using cell experiments. First, the TiO2 aggregates had to be cleaved after they were redispersed in water, toluene or Tris base so that a controlled coating of individual nanoparticles could then be carried out. The influence of ultrasound in the form of a two-minute ultrasound tip treatment provided the lowest particle sizes in the DLS measurement. The coatings were developed with APTES, dopamine and PEG-SH under the influence of different ultrasonic tip times, concentrations, temperatures, pH values, salts as well as various magnetic stirring techniques and washing processes. With the characterization methods via dynamic light scattering, zeta potential measurement, infrared spectroscopy, SEM and STEM, each coating was analyzed and in this way the optimal manufacturing method was developed. Finally, the influence of uncoated and APTES, PDA and PEG-SH coated TiO2 nanoparticles with increasing silver content was examined in vitro using healthy cells and tumor cells. The cells were incubated with the particles for 24 h and then characterized by flow cytometry. In general, only a minor effect of the particles on the cells was observed. The statement advertised in the literature that silver doped TiO2 is able to kill degenerate cells while sparing healthy cells could not be confirmed. However, some factors had an impact on vitality and cell count. The increasing proportion of silver in the cells played a role, which had an effect on the TiO2 nanoparticles. The cell count and vitality decreased more with increasing Ag content. An increasing concentration of the coated particles also had a positive effect on the decrease in the number of cells. In particular, the adherently growing tumor cell line Panc02 was sensitive to the coated and uncoated particles. The coating that had the greatest impact on cell count and vitality loss was clearly the PDA coating. KW - Titandioxid KW - Nanopartikel KW - Beschichtung KW - Beschichtung von Titandioxid-Nanopartikeln KW - Vereinzelung von Partikeln KW - Silberdotierung KW - biofunctional coating KW - silver doped titanium dioxide nanoparticles Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-205100 ER - TY - THES A1 - Griebel, Dragan T1 - Fluoreszente, hybride Nanosensoren auf Silicatbasis für die Bioanalytik T1 - Fluorescent, hybrid silica nanosensors for bioanalytic applications N2 - Es wurde ein Leitpartikeltyp mit hoher Fluoreszenz sowie einem Absorptionsbereich oberhalb von 600 nm evaluiert. Zur Anbindung der hochspezifisch wirkenden Antikörper wurde die Teilchenoberfläche mit Carboxylgruppen funktionalisiert. Die Darstellung dieser sphärischen, komplex aufgebauten erfolgte über eine nasschemische Synthese. Die synthetisierten Partikel besitzen eine hohe Fluoreszenzintensität, gutes Chromatographierverhalten und spezifische Beladbarkeit mit monoklonalen Antikörpern (z.B. Troponin T) auf einer mit Carboxylgruppen modifizierten Partikeloberfläche. Auf die Partikel mit dem favorisierten Fluorophor musste eine zusätzliche Silicathülle aufkondensiert werden, damit diese im Anschluss erfolgreich mit Antikörpern beladen werden konnte. Die erhaltenen partikulären Systeme wurden sowohl qualitativ als auch quantitativ charakterisiert. Die Fluoreszenzintensität dieser dotierten Kern-Schale-Partikel konnte soweit optimiert werden, dass sich klinisch relevante und noch höhere Sensitivitäten in Prüfteststreifen detektieren ließen. Weiterhin wurden neuartige Fluoralkylsilan und Fluorophor codotierte Silicat-Nanopartikel synthetisiert, die auf Anhieb eine gute untere Nachweisgrenze von Troponin erzielten. Durch UV-VIS- und Fluoreszenz-Untersuchungen sowie Konjugations- und Prüfteststreifen-Versuche konnte gezeigt werden, dass die Cokondensation des Fluoralkylsilans in einer Erhöhung von Absorption und Fluoreszenz der Partikel resultiert. Weitere Untersuchungen von zeigten, dass eine zusätzliche Oberflächenmodifizierung mit Fluoralkylsilan zu einer signifikanten Verschlechterung der Konjugationseigenschaften mit Antikörpern führt. Alternative Detekorreagenzien und -methoden wurden ebenfalls untersucht. So konnte der kationische Komplex Tris-(1,10-phenantrolin)ruthenium(II)-dichlorid erfolgreich in monodisperse Silicat-Partikel eingebaut werden. Aufgrund ihrer geringen Sauerstoffpermeabilität sind sie als impermeabler Referenzstandard in O2-Sensoren geeignet. Eine andere untersuchte Detektionsmethode basiert auf zeitaufgelöster Fluoreszenz (TRF). Hierbei werden hauptsächlich Lanthanoid-Komplexe eingesetzt. Am besten untersucht sind Europium-Komplexe, welche meistens Diketone als Liganden besitzen. Bislang konnten diese neutralen Komplexe jedoch nicht in polare Silicatpartikel-Matrizes eingebaut werden. Durch Einsatz von 3,3,3-Trifluoropropyltrimethoxysilan gelang es erstmalig, einen Europium(III)-tris-4,4,4-trifluoro-1-(2-naphthoyl)-1,3-butandion-Komplex (Eu(TNB)3) in hydrophobierte Silicat-Nanopartikeln physikalisch einzubauen. TRF-Messungen zeigten Abklingzeiten von ca. 300 µs. In diesem bislang nicht verfügbaren Partikel-Typ konnten positive Eigenschaften von Latex- und Silicatpartikeln kombiniert werden. Auch einige Porphyrinkomplexe mit langen Fluoreszenzlebensdauern sind in Silicat-Nanopartikel eingebaut worden. Der neutrale Komplex 5,10,15,20-Tetrakis(4-carboxyphenyl)-porphyrin-Pd(II) konnte nur durch vorhergehende Silanisierung erfolgreich eingebunden werden. Die erhaltenen sphärischen Partikel weisen eine Größenverteilung von 200-300 nm auf. Ein weiteres, kationisches Porphyrin (5,10,15,20-Tetrakis(N-methyl-4-pyridyl)-21,23H-porphyrin-Zn(II)) konnte ebenfalls erfolgreich in etwa 140 nm große Silicat-Nanopartikel blutungsstabil eingebaut werden. N2 - The aim was to develop monodisperse detector reagents based on nanoparticles, that can be used as biosensors for medical diagnostics and other bioanalytical applications. A particle-type with a high fluorescence intensity and an absorption range around or above 600 nm was evaluated. The particle surface was functionalized with carboxyl groups to allow for covalent attachment of specific antibodies through which the particles can bind to target molecules. The synthesis of these complex spherical particles was done following the wet-chemical Sol-Gel-Process. The particles could be adjusted to the desired requirements: high fluorescence quantum yields, good chromatographic behaviour , efficient conjugation of antibodies (e.g. Troponin T) to a carboxyl modified particle surface. The nanoparticles with the favoured fluorophore had first to be covered with an additional silica shell in order to prepare them for loading with antibodies afterwards. The resulting particles have been characterized qualitatively as well as quantitatively. Furthermore, novel silica nanoparticles have been synthesized by cocondensation of a fluoroalkylsilane and a fluorophore. UV-VIS- and fluorescence spectroscopy as well as conjugational and biosensor tests showed that the cocondensation has positive effects on the absorption and on the fluorescence of the particles. Alternative detection reagents and methods have also been investigated. Thus, the cationic complex Tris-(1,10-phenantrolin)ruthenium(II)-dichloride could successfully be integrated into monodisperse silica particles. These particles are suitable as a standard substrate in O2-sensors because of their low oxygen permeability. The required physical entrapment quantity of the complex as well as the desired low permeability could be demonstrated successfully. Time resolved flourescence (TRF) was applied as an additional detection method. Mainly lanthanoid complexes are used within this method. Most commonly used are Eu(III)-b-diketonate complexes. Up to now, these neutral complexes could not be integrated into the polar silica particle matrix. For the first time, an Europium(III)-tris-4,4,4-trifluoro-1-(2-naphthoyl)-1,3-butandion-complex (Eu(TNB)3 could be embedded into silica particles hydrophobized with 3,3,3-Trifluoropropyltrimethoxysilane. The embedment into the 140 nm diameter nanoparticles has been proved quantitatively as well as qualitatively TRF measurements detected a fluorescence lifetime of approximately 300 µs. In this - up to now- unique particle type the positive properties of latex particles and silica particles could be combined. Some porphyrin complexes possess long fluorescence lifetimes and, therefore, have been investigated. The neutral 5,10,15,20-Tetrakis(4-carboxyphenyl)-porphyrin-Pd(II) complex could only be integrated successfully into silica nanoparticles after having been silanized. The resulting spheric particles have a particle size distribution of 200- 300 nm. Another cationic porphyrin (5,10,15,20-Tetrakis(N-methyl-4-pyridyl)-21,23H-porphyrin-Zn(II)) could also be integrated successfully and without bleeding into 140 nm sized monodisperse silica particles. KW - Silicate KW - Nanopartikel KW - Fluoreszenzmarkierung KW - Biologisches Material KW - Analyse KW - Nanosilicatpartikel KW - hybrid KW - Fluoreszenz KW - nano KW - nanoparticles KW - hybrid KW - fluorescence Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-6153 ER - TY - THES A1 - Zimmermann, Franz-Zeno T1 - Genotoxizität in Miniorgankulturen humaner nasaler Mukosa nach repetitiver Exposition mit Zinkoxid Nanopartikeln T1 - Genotoxicity in mini organ cultures of human nasal mucosa after repetetive exposition with zinc oxide nanoparticles N2 - Diese Studie beschäftigt sich mit den toxischen Effekten von Zinkoxid Nanopartikeln (ZnO NP) auf humane Nasenschleimhautzellen. Speziell wurde eine mögliche Kumulation von DNS-Schäden und deren Reparatur analysiert. Zu diesem Zweck wurde ein dreidimensionales Kultursystem, sogenannte Miniorgankulturen, aus humaner nasaler Mukosa verwendet. Eine Charakterisierung der verwendeten Zinkoxid Nanopartikel erfolgte unter dem Transmissionselektronenmikroskop (TEM), mittels dynamischer Lichtstreuung (DLS) und durch eine Zetapotentialmessung. Nach einer Woche Kultivierung fand eine Exposition der MOK mit einer Zinkoxid Nanopartikel Suspension in einer Konzentration von 0,1 µg/ml und 5 µg/ml statt. Als Positivkontrolle wurde in diesem Versuch 200µM Methymethansulfonat (MMS) zugesetzt. Es erfolgten drei jeweils einstündige Inkubationsphasen, wobei nach jeder Stunde ein Teil der MOKs für den Cometassay entnommen wurde. Nach dreimaliger Exposition wurden die verbliebenen MOKs für 24 Stunden zur Regeneration in unversetztem Nährmedium belassen und dann dem Cometassay zugeführt. Ergänzend wurde ein Sandwich ELISA zur Detektion von Caspase 3 durchgeführt. Zn2+ Ionen wurden im Zellkulturmedium analysiert. Der Nachweis von reaktiven Sauerstoffspezies (ROS) erfolgte fluoreszenzmikroskopisch. Die DLS konnte eine durchschnittliche Partikelaggregatgröße von 354 nm nachweisen und das Zetapotential betrug -11,2 mV. Die im Cometassay festgestellten DNS-Schäden zeigten bei einer Zinkoxid Nanopartikel Konzentration von 0,1 µg/ml erst nach der Regenerationsphase von 24 Stunden einen signifikanten Anstieg, während 5 µg/ml Zinkoxid Nanopartikel zu jedem Zeitpunkt einen signifikanten Anstieg der DNS Fragmentation bewirkten. Das Ausmaß an Strangbrüchen nach 24 Stunden stieg auch hier nach 24stündiger Regenerationsphase nochmals an. 200 µM MMS induzierten ebenfalls einen signifikanten Anstieg der OTM-Werte bei einer, zwei und drei Stunden. Im Laufe der Regenerationsphase führten Reparaturmechanismen zu einem Absinken der OTM-Werte. Der Sandwich ELISA zeigte keinen signifikanten Anstieg der Caspase 3 Werte. Im Nährmedium konnte eine Zn2+ Ionenkonzentration von 2,8 µmol/ml nach einer Inkubation mit 0,1 µg/ml Zinkoxid Nanopartikeln festgestellt werden. Bei einer Inkubation mit 5 µg/ml Zinkoxid Nanopartikeln zeigte sich eine Ionenkonzentration von 52,7 µmol/ml. Intrazelluläre ROS konnte nur bei einer Exposition mit 5 µmol/ml Zinkoxid Nanopartikeln nachgewiesen werden. Diese Daten lassen den Schluss zu, dass Zinkoxid Nanopartikel in den verwendeten Konzentrationen genotoxisch wirken, aber keine zytotoxische Wirkung entfalten. Die Schädigung kumuliert und schreitet während der Regenerationsphase noch fort. Eine multifaktorielle Schädigung der DNS, sowohl durch direkte Interaktion der Partikel mit dem Erbgut, als auch über entstandene ROS und Zn2+ Ionen, ist anzunehmen. N2 - This study examines the toxic effects of zincoxide nanoparticles (ZnO NPs) in nasal mucosa cells. Especially the possible accumulation of DNA damages und their reparation was analysed. For this purpose we used mini organ cultures (MOCs) out of human nasal mucosa. The zinc oxide nanoparticles were characterized under a transmission electron microscope and by zeta potential measurement. After one week of cultivation, the MOCs were exposed to a ZnO NP suspension. The concentrations were 0,1 µg/ml and 5 µg/ml. 200µM methylmethane sulfonate (MMS) was used as positive control. The MOCs were incubated three times for one hour. After each hour some of the MOCs were analysed with the Cometassay. The last MOCs stayed for 24 hours in the cell culture medium for regeneration. A sandwiche ELISA was performed to detect Caspase 3. Zn2+ ions were analysed in the cell culture medium. To detect reactive oxygen species (ROS), the cells were analysed under a fluorescence microscope. The average particle size was 345 nm. The zeta potential was –11,mV. DNA damage was detected to ZnO-NPs at 0.1 μg/ml ZnO-NPs after a 24h lasting regeneration time. 5 µg/ml ZnO NPs damaged the DNA at every point of time. The sandwich ELISA showed no significant increase of Caspase 3 in the medium. 0,1 µg/ml ZnO NPs resulted in a Zn2+ ion concentration of 2,8 µmol/ml and 5 µg/ml in a concentration of 52,7 µmol/ml. ROS could only be detected after an incubation with 5 µg/ml ZnO NPs. Thus the results suggest that ZnO NP in these concentrations are genotoxic but not zytotoxic. The damage cumulates and is increasing throughout the regeneration time. A multifactorial damage of the DNA, through direct interaction of the particles and also through ROS and zinc ions, is to suppose. KW - Nasenschleimhaut KW - Nanopartikel KW - Zinkoxid KW - Miniorgankultur KW - nanoparticle KW - nasal mucosa KW - zinc oxide KW - mini organ culture Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-72641 ER - TY - THES A1 - Heyer, Steffen T1 - Herstellung dotierter Nanodiamantpartikel und ihre Funktionalisierung mit schwefelhaltigen Gruppen T1 - Synthesis of doped nanodiamonds and their functionalization with sulfur-containing groups N2 - In dieser Dissertation werden Methoden zur Darstellung von Stickstoff- und Bor-dotierten Nanodiamantpartikeln durch Vermahlung von makroskopischem HPHT- und CVD-Diamant mit unterschiedlichen Mühlen und Mahlverfahren beschrieben. Untersucht wird dabei der Zusammenhang von erzielten Teilchengrößen nach dem Mahlen und den Kristallitgrößen der Ausgangsdiamanten sowie der angewandten Mahlmethode. Durch Anwendung verschiedener oxidativer Methoden wird während des Mahlens entstehender sp2-Kohlenstoff entfernt. Ebenfalls wird deren Einfluss auf das Fluoreszenzverhalten NV-haltiger Nanodiamantpartikel analysiert. Des Weiteren werden Syntheserouten zur kontrolliert ablaufender Oberflächenflächenfunktionalisierung von Nanodiamant mit schwefelhaltigen Gruppen wie Thiolen, Trithiocarbonaten und Disulfiden gezeigt, welche eine selektive Anbindung der Diamantpartikel an Goldstrukturen ermöglicht. Diese Verfahren werden an Detonationsdiamant sowie fluoreszierendem HPHT- und CVD-Diamantpartikeln angewandt. Gegebenfalls kann nach erfolgreicher Anbindung fluoreszierender Nanodiamantpartikel an Goldnanostrukturen unter Ausnutzung von Plasmonenresonanz die einzigartigen Spineigenschaften der NV-Zentren mit Hinblick auf einen möglichen Einsatz Stickstoff-dotierter Diamantnanopartikel in der Quanteninformationsverarbeitung untersucht werden. N2 - This dissertation presents methods to create nitrogen and boron doped nanodiamond particles by milling macroscopic HPHT- and CVD-diamond in different milling procedures. In this context, the correlation between resulting particle sizes after the milling with the crystallite sizes of the diamond starting material and the applied milling method is investigated. By application of different oxidative methods, sp2 carbon, that was created in the milling process, can be removed. In addition, the influence of the oxidation processes on the fluorescence properties of NV-are analysed. Furthermore, synthetic pathways for a controlled surface grafting of nanodiamond with sulfur containing groups like thiols, trithiocarbonates and disulfides which enable the functionalized diamonds to bind selectivly on gold surfaces are developed within this thesis. The syntheses are applied to detonation diamond aswell as fluorescent HPHT- and CVD-diamond. After a successful attachment of the functionalized nanodiamonds to goldnanostructures, the unique spinproperties of NV-centers can be studied with regard to a possible application of N-doped diamond nanoparticles in quantum computing. KW - Diamant KW - Nanopartikel KW - Dotierung KW - Mahlen KW - Nanodiamant KW - nanodiamond KW - boron-doped diamond KW - Oberflächenfunktionalisierung KW - Schwefel-Funktionalisierung KW - Vermahlung KW - NV-Zentren KW - Bor-dotiert Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-123465 ER - TY - THES A1 - Gegg, Tanja Susanne T1 - In Vitro Toxizität der Nanopartikel Graphen und Siliciumdioxid für die Medikamentenapplikation T1 - In vitro toxicity of the nanoparticles Graphene and Silicon dioxide for drug targeting N2 - Graphen und Siliciumdioxid Nanopartikel sind als Trägersubstanz für Medikamente beim Drug Targeting von Interesse. Diese Arbeit ist eine toxikologische Untersuchung der Nanopartikel Graphen und Siliciumdioxid im Zellmodell. Dabei wurden Graphen Nanopartikel mit einer Dicke von 6 bis 8 nm und einer Breite von 15 µm verwendet. Die verwendeten Siliciumdioxid Nanopartikel waren kugelförmig und porös mit einer Partikel-Größe von 5 bis 20 nm. Die dosisabhängige Toxizität (Konzentrationen 0,01 mg/ml, 0,1 mg/ml und 1 mg/ml, Inkubation über 24 Stunden) gegenüber 5 verschiedenen Zelllinien (cerebEND, Caco-2, Hep G2, HEK-293, H441) wurde geprüft. Dabei kamen Zellviabilitätstests (CellTiter-Glo Assay, EZ4U-Test) zum Einsatz. Zudem wurde mit den Apoptose-Markern Bax und Caspase-3 auf Gen- und Proteinebene (Polymerasekettenreaktion und Western Blot) überprüft, ob eine Apoptose eingeleitet wurde. Zur Untersuchung der Zellviabilität wurde der CellTiter-Glo Assay verwendet. Für Graphen Nanopartikel zeigte sich ab einer Konzentration von 1 mg/ml bei den Zelllinien HEK-293 und H441 ein statistisch signifikanter Abfall der Zellviabilität. CerebEND und Hep G2 Zellen reagierten auf Graphen Nanopartikel ab einer Konzentration von 1 mg/ml ebenfalls mit einem deutlichen Abfall der Zellviabilität, diese Ergebnisse waren jedoch nicht statistisch signifikant. Die Zelllinie Caco-2 zeigte sich von den Graphen Nanopartikeln unbeeindruckt, es kam zu keiner statistisch signifikanten Veränderung der Zellviabilität. Siliciumdioxid Nanopartikel bewirkten ab einer Konzentration von 1 mg/ml einen statistisch signifikanten Abfall der Zellviabilität bei den Zelllinien cerebEND, HEK-293 und H441. HepG2 Zellen zeigten bei 1 mg/ml Siliciumdioxid einen deutlichen aber statistisch nicht signifikanten Abfall der Zellviabilität. Die Zelllinie Caco-2 erwies sich auch bei Siliciumdioxid Nanopartikel als äußerst robust und zeigte keine statistisch signifikanten Veränderungen der Zellviabilität. Messungen der Zellviabilität auf Grundlage von Adsorptionsmessung, wie beim EZ4U-Test, hatten sich als ungeeignet erwiesen, da die Eigenfarbe der Nanopartikel Graphen und Siliciumdioxid mit dieser Messung interferierte. Zudem wurde geprüft, ob die bei einem Teil der Zelllinien eingetretene toxische Wirkung der Nanopartikel ab einer Konzentration von 1 mg/ml durch Nekrose oder durch Apoptose zustande kam. Die Polymerasekettenreaktion zeigte mit einer einzigen Ausnahme keine statistisch signifikante Erhöhung der Genexpression für Bax und Caspase-3 und gab somit auch keine Hinweise auf die Einleitung einer Apoptose. Im Western Blot zeigte sich keine statistisch signifikante Erhöhung der Proteinexpression von Bax und Caspase-3. Zudem konnte im Western Blot auch keine aktivierte Caspase-3 nachgewiesen werden. Somit lagen auf Grundlage von Polymerasekettenreaktion und Western Blot keine Hinweise auf das Eintreten einer Apoptose vor. Die toxische Wirkung der Nanopartikel Graphen und Siliciumdioxid, die bei einem Teil der Zelllinien ab einer Konzentration von 1 mg/ml nachgewiesen werden konnte, beruhte demnach auf Nekrose. N2 - Graphene and silicon dioxide nanoparticles are of interest as drug carriers for controlled drug delivery systems. This thesis is an evaluation of the toxic properties of the nanoparticles Graphene and Silicon dioxide based on tests on cell culture. The Graphene nanoplatelets were 6 to 8 nm thick and 15 µm wide. The Silicon dioxide nanoparticles were spherical and porous with a particle size of 5 to 20 nm. The dose dependent toxicity (concentrations 0,01 mg/ml, 0,1 mg/ml und 1 mg/ml, incubation over 24 hours) was tested on 5 different cell lines (cerebEND, Caco-2, Hep G2, HEK-293, H441). I used cell viability test (CellTiter-Glo Assay, EZ4U-test). In addition, I used PCR (Polymerase chain reaction) and western blot to detect the apoptosis markers Bax and Caspase-3, to see if the nanoparticles cause an apoptosis or a necrosis. For investigating the cell viability, I used the CellTiter-Glo Assay. Graphene nanoplatelets showed from a concentration of 1 mg/ml for the cell lines HEK-293 und H441 a statistically significant decrease of cell viability. CerebEND and Hep G2 cells reacted on Graphene nanoplatelets from a concentration of 1 mg/ml with a clearly decrease in cell viability, but these results were not statistically significant. The cell line Coco-2 showed no decrease in cell viability after the incubation with Graphene nanoplatelets. Silicon dioxide nanoparticles showed from a concentration of 1 mg/ml a statistic significant decrease of cell viability in the cell lines cerebEND, HEK-293 and H441. The Hep G2 cells showed a decrease in cell viability as well, but the results were not statistically significant. The cell line Caco-2 showed no decrease in cell viability after the incubation with Silicon dioxide nanoparticles. Cell viability tests based on the messurement of adsorption like the EZ4U-test, proved not suitable for this setting, because the own color of the nanoparticles interfered with the measurement. In addition, I tested if the nanoparticles caused an apoptosis or a necrosis. The PCR showed with one exception no statistically significant increase in the gene expression of Bax and Caspase-3 and therefore no proof of apoptosis. The western blot showed no statistically significant increase in the protein expression of Bax and Caspase-3. And it detected no activated Caspase-3. There was based on PCR and western blot no sign for the cells to enter in apoptosis. The toxic properties of the nanoparticles Graphene and Silicon dioxide, that was shown in a part of the cell lines from a concentration of 1 mg/ml, was therefore based on necrosis. KW - Nanopartikel KW - Toxizität KW - Graphen KW - Siliciumdioxid KW - Drug Targeting KW - Targeted drug delivery KW - Zellkultur Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-330562 ER - TY - THES A1 - Scherdel, Christian T1 - Kohlenstoffmaterialien mit nanoskaliger Morphologie - Entwicklung neuartiger Syntheserouten T1 - Carbon material featuring nanoscale morphology - Development of novel synthesis routes N2 - Hochporöse Kohlenstoffaerogele, die über den Sol-Gel-Prozeß auf der Basis von Resorzin und Formaldehyd hergestellt werden, sind Werkstoffe mit beeindruckenden physikalischen Eigenschaften. Leider werden bisher nur geringe Mengen an Kohlenstoffaerogelen produziert und aus Kostengründen auf günstigere Materialien mit vergleichsweise schlechteren Eigenschaften zurückgegriffen. Um diesen Nachteil zu nivellieren lag die Motivation der vorliegenden Arbeit in der Entwicklung neuer Syntheserouten für Kohlenstoffmaterialien mit nanoskaliger Morphologie, wobei insbesondere auf kostengünstige Edukte und/oder einfache Prozessierung zurückgegriffen werden sollte. Als in Frage kommende Eduktsysteme wurden Zucker, sowie Hydroxybenzol-Formaldehyd-Derivate ausgewählt. Die hergestellten Kohlenstoffe wurden hauptsächlich mit Elektronenmikroskopie, Gassorption und Röntgenkleinwinkelstreuung (SAXS) charakterisiert. Um Fehlinterpretationen der experimentellen Daten für das neue Materialsystem zu vermeiden, war ein umfangreiches Wissen zu den Charakterisierungsmethoden und den diesen zugrundeliegenden physikalischen Prinzipien notwendig. Kohlenstoffpulver basierend auf sphärischen Resorzin-Formaldehyd Suspensionen und Sedimenten bilden eine völlig neue Möglichkeit zur Erzeugung von Kohlenstoffnanokugeln. Im Rahmen dieser Arbeit wurde deshalb systematisch der Bereich der Syntheseparameter im RF-System zu den nicht-monolithischen Parametersätzen hin vervollständigt. Anhand der bestimmten Daten konnte diese Stoffklasse umfassend und detailliert charakterisiert und interpretiert werden. Die Partikelgröße hängt im Wesentlichen von der Katalysatorkonzentration und in geringerem Maße von der Eduktmenge in der Startlösung ab. Die ermittelte untere Grenze der Partikelgröße aus stabilen kolloidalen Dispersionen beträgt ca. 30 nm. Größere Partikel als 5 µm konnten trotz Modifikation der Syntheseroute nicht erzeugt werden. Eine Abschätzung über den Aggregationsgrad der Kohlenstoffpulver wurde durchgeführt. Eine Beimischung von Phenol verringert in diesem System zum einen die Partikelgröße und erzeugt zunehmend nicht-sphärische Strukturen. Die aus Gassorption, SAXS und dynamischer Lichtstreuung (DLS) ermittelten Partikelgrößen stimmen gut überein. Bei der Pyrolyse schrumpfen die Partikel auf 84% des Ausgangswerts (Partikeldurchmesser). Ein Fokus dieser Arbeit lag in der Herstellung poröser Kohlenstoffe mit Phenol und Formaldehyd (PF) als Eduktbasis und unterkritischer Trocknung (Kohlenstoffxerogele). Um die Bandbreite der Eigenschaften der resultierenden Kohlenstoffxerogele zu erweitern, wurden zahlreiche Modifikationen der Syntheseparameter und im Herstellungsprozeß durchgeführt. Die Ergebnisse zeigen, daß im Eduktsystem Phenol-Formaldehyd in wäßriger Lösung mit Na2CO3 als basischem Katalysator prinzipiell poröse Xerogele herstellbar sind; allerdings verhindert eine ungewöhnliche Gelierkinetik (Flockenbildung statt Sol-Gel-Übergang) eine umfassende Interpretation des Systems, da die Reproduzierbarkeit der Ergebnisse nicht gewährleistet ist. Bei Phenol-Formaldehyd in wäßriger Lösung und NaOH als Katalysator kommt es meist zu einem Kollabieren des Gelnetzwerks während der Trocknung. Lediglich bei hohem Formaldehydüberschuß zeigt sich ein enger Bereich, in dem Xerogele mit geringer Dichte (rhomin = 0,22 g/cm3) und relevantem Mesoporenvolumen von bis zu 0,59 cm3/g synthetisierbar sind. Die interessanteste Kombination im PF-System ergibt sich mit HCl als Katalysator und n-Propanol als Lösungsmittel. Hier sind hochporöse Kohlenstoffxerogele mit geringen Dichten (rhomin = 0,23 g/cm3) und für Xerogele sehr hoher Mesoporosität von bis zu Vmeso = 0,85 cm3/g möglich. Damit ist es im Rahmen dieser Arbeit erstmals gelungen über konvektive Trocknung homogene hochporöse Xerogel-Formkörper auf PF-Basis zu synthetisieren. Aus der Überwachung des Sol-Gel-Prozesses mit Detektion der Soltemperatur konnten wichtige Erkenntnisse über exo- und endotherme Vorgänge gewonnen werden. Zudem zeigt die Zeitabhängigkeit der Soltemperatur Gemeinsamkeiten für alle untersuchten Hydroxybenzol-Formaldehyd-Systeme. So kann der Gelpunkt der Ansätze zuverlässig und auch reproduzierbar anhand eines zweiten lokalen Temperaturmaximums ermittelt werden, welches mit einer Gelpunktsenthalpie korreliert wird. Damit ist auch eine Prozeßkontrolle, z.B. für die Kombination mit Partikeltechnologien, möglich. Die zugrundeliegenden Strukturbildungsmechanismen, Sol-Gel-Prozeß einerseits und Trocknung andererseits, wurden in-situ mittels SAXS beobachtet und anhand der gewonnenen Daten diskutiert und bewertet. Eine vollständige Adaption des etablierten und akzeptierten Bildungsmechanismus von RF basierten Aerogelen (Partikelbildung aus Kondensationskeimen und Partikelwachstum) für das PF-System wird ausgeschlossen. Vielmehr scheint bei den untersuchten PF-Systemen auch eine Mikrophasenseparation als konkurrierender Prozeß zur Partikelbildung von Relevanz zu sein. N2 - Highly porous carbon aerogels derived via the sol-gel-process based on the precursors resorcinol and formaldehyde are materials with impressive physical properties. In principle, they are suited for many applications (e.g. thermal insulations, components in electrochemical devices). Unfortunately, up to now, there are only small amounts of carbon aerogels available. Due to cost efficiency, cheaper materials with less favourable properties compared to carbon aerogels are used. To compensate for this disadvantage, the motivation for this work was the development of new synthesis routes for carbon materials with nanostructured morphology, applying in particular cheap precursors and/or simple processing. As precursor systems, sugar as well as hydroxybenzene-formaldehyde-derivatives were chosen. The produced carbons were characterised in particular by electron microscopy, gas sorption and small-angle X-ray scattering (SAXS). To avoid misinterpretation of the experimental data of the new materials system, extensive knowledge concerning the characterization methods and their underlying physical principles are essential. Carbon powders based on spherical particles derived from suspensions and sediments of resorcinol-formaldehyde (RF) solutions establish a completely new possibility to generate carbon nanospheres. Within the framework of this thesis the range of the synthesis parameters of the RF-system towards the non-monolithic parameter sets was therefore systematically completed. These materials were characterized and interpreted extensively and in detail by using the derived experimental data. The particle size depends essentially on the catalyst concentration rather than on the amount of precursors in the initial solution. The lower limit particle size derived from stable colloidal suspensions is about 30 nm. Larger particles than 5 µm could not be synthesized, even when modifying the synthesis route. An estimate for the level of aggregation of the carbon powders was determined. Admixing of phenol decreases the particle size in this system and generates increasingly non-spherical structures. The evaluated particle sizes derived from gas sorption, SAXS and dynamic light scattering (DLS) are in good agreement with each other. During pyrolysis, the particles shrink to 84% of the initial value (particle size). One goal of this work was the synthesis of porous carbons with phenol and formaldehyde (PF) as precursors and subcritical drying (carbon xerogels). To extend the possible properties of the resulting carbon xerogels, several modifications of the synthesis parameters as well as in the production process were conducted. The results show, that with the precursors phenol-formaldehyde in aqueous solution using Na2CO3 as catalyst, porous xerogels can in principle be synthesized. However, the unusual gelation kinetics (flake forming instead of sol-gel-transition) prevents a detailed interpretation of this system, because the reproducibility of the results can not be ensured. With the system phenol and formaldehyde in aqueous solution using NaOH as catalyst, the gel network mostly collapses during drying. Only with excess formaldehyde a range in the synthesis parameters exists, where xerogels with low density (rhomin = 0,22 g/cm3) and relevant mesopore volume of up to 0,59 cm3/g can be synthesized. The most interesting combination of PF is with HCl as catalyst and n-propanol as solvent. With this system, highly porous carbon xerogels with low densities (rhomin = 0,23 g/cm3) and for xerogels high mesoporosity of up to Vmeso = 0,85 cm3/g can be synthesized. Hence, within the framework of this thesis highly porous monolithic xerogels based on PF as precursors in combination with subcritical drying have been successfully synthesiszed for the first time. Monitoring of the sol-gel-process by detection of the sol temperature provided important information about exo- and endothermal reactions. Moreover, the temperature dependence of the sol shows similarities for all investigated hydroxybenzene-formaldehyde combinations. The gelling point of the precursor systems can be reproduced reliably by determining a second local maximum of the sol temperature, which can be correlated with an enthalpy of gelation (second order process). By this way, a process control is possible, e.g. for the combination with particle technologies. The basic mechanisms of structure formation, i.e. the sol-gel-process on the one hand and the subcritical drying on the other hand were monitored in-situ by SAXS and discussed on the base of the obtained data. A complete adaptation of the established and accepted structure formation mechanism of RF based aerogels (forming and growing of particles by) can be ruled out for the PF-system. Moreover, microphase separation seems to be a relevant competing process for the particle forming in the PF-system. KW - Sol-Gel-Verfahren KW - Kohlenstoff KW - Aerogel KW - Xerogel KW - Phenol-Formaldehyd-Kondensationsprodukt KW - Nanopartikel KW - Adsorption KW - Röntgen-Kleinwinkelstreuung KW - sol-gel-technology KW - xerogel KW - phenolic resin KW - carbon KW - nanoparticle Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-45325 ER - TY - THES A1 - Moratin, Helena Anne T1 - Mechanismen Zinkoxid-Nanopartikel-assoziierter Toxizität am Beispiel einer humanen Plattenepithelkarzinom-Zelllinie und primärer humaner mesenchymaler Stammzellen T1 - Analysis of zinc oxide nanoparticle-associated mechanisms of toxicity using the example of a human squamous cell carcinoma cell line and primary human mesenchymal stem cells N2 - Einleitung: Zinkoxid (ZnO) ist eines der am häufigsten für industrielle Produktionen und Konsumgüter eingesetzten Nanomaterialien. Zytotoxizität von ZnO-Nanopartikeln (NP) war bereits Gegenstand einiger Studien, jedoch sind die molekularen Schädigungsmechanismen nicht gänzlich geklärt. Über genotoxische Eigenschaften, die bereits bei sub-zytotoxischen Dosen auftreten können, ist im Allgemeinen weniger bekannt. Ziel dieser Studie war die Erstellung eines umfassenden Toxizitätsprofils von ZnO-NP durch Einsatz multipler Testsysteme. Methoden: Neben der Plattenepithelkarzinom-Zelllinie FaDu wurden humane mesenchymale Knochenmarkstammzellen (BMSC) für unterschiedliche Zeiträume und Konzentrationen mit ZnO-NP behandelt. Zytotoxizität, Apoptoseinduktion und Zellzyklusalteration wurden durch MTT-Test, PCR und Durchflusszytometrie analysiert. Mit dem fpg-modifizierten Comet Assay wurden der Einfluss von oxidativem Stress auf das Gesamtausmaß der DNA-Schädigung untersucht. Ergebnisse: ZnO-NP führten im MTT-Test ab 8 µg/ml zu einer Reduktion der Vitalität in FaDu-Zellen. Durchflusszytometrisch wurden eine dosis- und zeitabhängige Zunahme von Apoptose sowie Veränderungen des Zellzyklus nachgewiesen. Im Comet Assay konnte nach Inkubation mit 5 µg/ml ZnO-NP eine signifikante DNA-Fragmentierung in BMSC nachgewiesen werden. Bei allen getesteten Konzentrationen wurde oxidativer Stress als wichtiger Einflussfaktor der Schädigung nachgewiesen. Diskussion: Vorliegende Studie liefert Hinweise dafür, dass ZnO-NP toxisch sind. Gegenwärtig ist eine definitive Aussage über das schädigende Potenzial von NP nicht zu treffen, da der Vergleich verschiedener Studien kaum möglich ist. Gerade die Verwendung von ZnO-NP als Bestandteil von Kosmetikprodukten, die repetitiv in geringen Mengen von Verbrauchern appliziert werden, sollte jedoch kritisch betrachtet werden. N2 - Introduction: Zinc oxide (ZnO) is among the most commonly used nanomaterials for consumer products. Cytotoxicity of ZnO-nanoparticles (ZnO-NP) has already been addressed in several studies; however, there is still a lack of knowledge concerning the molecular mechanisms of toxicity. As to genotoxicity, which can already occur at sub-toxic doses, data is generally rare. It was therefore the aim of this study to establish a broad profile of toxicity for ZnO-NP by applying multiple test systems. Methods: Besides the head and neck squamous cell carcinoma-derived cell line FaDu, primary human bone marrow-derived mesenchymal stem cells (BMSC) were treated with ZnO-NP with variable doses and for different time periods. Cytotoxicity, induction of apoptosis and cell cycle alteration were assessed by MTT-Test, PCR and flow cytometry. Fpg-modified Comet Assay was used to determine the influence of oxidative stress with regard to the total DNA-damage. Results: 8 µg/ml ZnO-NP reduced cell viability in FaDu cells in the MTT-Test. Dose- and time-dependent increase of apoptosis and alterations of the cell cycle were verified by flow cytometry. After incubation with 5 µg/ml ZnO-NP a significant DNA-fragmentation was measured in BMSC with the Comet Assay. In all tested concentrations oxidative stress could be identified as an important factor of cell damage. Discussion: This study provides evidence that ZnO-NP are toxic. At the current point a definite statement concerning the damaging potential of ZnO-NP is not to be made because the comparison between different studies is not possible. Yet especially the repetitive low-dose application of ZnO-NP as component of cosmetic products should be investigated toxicologically. KW - Zinkoxid KW - Nanopartikel KW - Zytotoxizität KW - Genotoxizität KW - Toxizität KW - Plattenepithelkarzinom KW - MSC Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-204237 ER - TY - THES A1 - Wehner, Tobias T1 - Multifunktionale Kompositmaterialien auf Basis lanthanidhaltiger Verbindungen mit lumineszierenden Nanopartikeln und superparamagnetischen Mikropartikeln T1 - Multifunctional composite materials based on lanthanide containing compounds with luminescent nanoparticles and superparamagnetic microparticles N2 - Die vorliegende Arbeit umfasst die Synthese und Charakterisierung 23 neuartiger, multifunktionaler Kompositmaterialien basierend auf lanthanidhaltigen Verbindungen sowie verschiedenen Nano- und Mikropartikeln. Die dargestellten Materialien konnten als Core/Shell-Systeme mit einem nano- bzw. mikropartikelhaltigen Kern und einer lanthanidhaltigen Hülle charakterisiert werden und vereinen aufgrund ihres Kompositcharakters die spezifischen Eigenschaften der Einzelkomponenten wie Lumineszenz, Superparamagnetismus oder Reflexionseigen-schaften miteinander. Zur Synthese multifunktionaler, lumineszierender Materialien wurden zirconylbasierte, lumineszierende Nanopartikel mit Lanthanidchloriden und lanthanidhaltigen MOFs funktionalisiert. Die Kompositsysteme LnCl3@ZrO(FMN) (FMN = Flavinmononukleotid, Ln = Y, Sc, La, Eu, Tb, Ho) ermöglichen eine Modifizierung der Lumineszenzeigenschaf-ten der Materialien abhängig von der Reaktionstemperatur sowie dem verwendeten Selten-Erd-Ion. Durch Variation der Nanopartikelkomponente konnte mittels der Kom-posite LnCl3@ZrO(MFP) (MFP = Methylfluoresceinphosphat) ein zusätzlicher sol-vatochromer Effekt der Systeme eingeführt werden, während das Kompositmaterial YCl3@ZrO(RP) (RP = Resorufinphosphat) eine andere Chromatizität zugänglich macht. Durch Modifizierung von ZrO(FMN)- und ZrO(MFP)-Nanopartikeln mit 3∞[Eu2(BDC)3]· 2DMF·2H2O (BDC2- = Benzol-1,4-dicarboxylat) wurden Kompositmaterialien dargestellt, die zwei Lumineszenzprozesse mit unterschiedlicher Chromatizität und unterschiedli-cher Anregbarkeit miteinander kombinieren und somit eine reversible Schaltbarkeit zwischen beiden Prozessen durch Variation der Anregungswellenlänge ermöglichen. Zur Synthese luminomagnetischer Materialien wurden superparamagnetische Fe3O4/SiO2-Mikropartikel mit einer Vielzahl lanthanidhaltiger MOFs, die sich hinsichtlich ihrer Lumineszenzeigenschaften und ihrer Stabilität gegenüber Luft und Wasser unterscheiden, modifiziert. Als MOFs wurden hierbei 2∞[Ln2Cl6(Bipy)3]·2Bipy (Bipy = 4,4‘-Bipyridin, Ln = Nd, Sm, Eu, Tb, Er), 3∞[Eu(Im)2], 3∞[Ba0.95Eu0.05(Im)2] (Im = Imidazolat) und 3∞[Eu2(BDC)3]·2DMF·2H2O eingesetzt. Die Variation der zur Funktionalisierung verwendeten Komponente oder eine Kombination mehrerer MOFs ermöglicht eine Anpassung der Lumineszenz der Kompositmaterialien innerhalb des kompletten sichtbaren Spektralbereichs sowie im NIR-Bereich. Die dargestellten luminomagnetische Kompositmaterialien mit wasserempfindlichen MOFs können zur Detektion von Wasser in verschiedenen organischen Lösungsmitteln verwendet werden und stellen somit eine mobile und einfach anwendbare Alternative zur Karl-Fischer-Titration mit einer vergleichbaren Sensitivität dar. So eignen sich die Kompositsysteme 2∞[Eu2Cl6(Bipy)3]·2Bipy@Fe3O4/SiO2 und 2∞[Eu2Cl6(Bipy)3]·2Bipy, 2∞[Tb2Cl6(Bipy)3]·2Bipy@Fe3O4/SiO2 als optische turn-off-Sensoren, während das Kom-posit 3∞[Eu2(BDC)3]·2DMF·2H2O,2∞[Tb2Cl6(Bipy)3]·2Bipy@Fe3O4/SiO2 als ratiometrischer Sensor verwendet werden kann. Als Alternative zu sphärischen Partikeln wurden auch anisotrope, stäbchenförmige Fe3O4/SiO2-Mikropartikel mittels 3∞[Eu2(BDC)3]·2DMF·2H2O modifiziert. Das resul-tierende Kompositmaterial vereint die isotropen Lumineszenzeigenschaften der MOF-Hülle mit der anisotropen Reflexion von sichtbarem Licht der. Durch die Wahl der Anregungswellenlänge und Richtung eines externen Magnetfelds wird eine stufenlose und reversible Schaltbarkeit zwischen isotropen und anisotropen Eigenschaften ermöglicht. Durch mechanochemische Umsetzung der MOF-Edukte [LnCl3(Py)4]·0.5Py (Ln = Eu, Ho) und 4,4‘-Bipyridin konnte eine Vielzahl von literaturbekannten lanthanidhaltigen Komplexen und Koordinationspolymeren mittels einer neuen und zeiteffizienten Syntheseroute dargestellt werden. Hierbei kann die Verknüpfungsdimension der resultierenden Produkte abhängig von verschiedenen Reaktionsparametern, die den Energieeintrags der Kugelmühle beeinflussen, gesteuert werden. N2 - The thesis at hand deals with the synthesis and characterization of 23 novel multi-functional composite materials that are based on lanthanide containing compounds as well as different nano- and microparticles. The synthesized compounds can be described as core/shell systems with a nanoparticle and microparticle containing core, respectively, and a lanthanide containing shell. Due to their composite character, the materials combine the specific properties of their single constituents such as luminescence, superparamagnetism or reflection properties. For the synthesis of multifunctional luminescent materials, zirconyl containing, lumines-cent nanoparticles were modified with lanthanide chlorides as well as lanthanide con-taining MOFs. The composite materials LnCl3@ZrO(FMN) (FMN = flavin mononucleo-tide, Ln = Y, Sc, La, Eu, Tb, Ho) enable a modification of the materials’ luminescence properties in dependence on the reaction temperature and the particular rare earth ion. Variation of the nanoparticle component leads on the one hand to formation of the sys-tem LnCl3@ZrO(MFP) (MFP = methylfluorescein phosphate), which exhibits a strong solvatochromic effect, and on the other hand to the composite YCl3@ZrO(RP) (RP = resorufin phosphate), which makes another chromaticity of the luminescence ac-cessible. The modification of ZrO(FMN) and ZrO(MFP) nanoparticles with 3∞[Eu2(BDC)3]· 2DMF·2H2O (BDC2- = benzene-1,4-dicarboxylate) results in composite materials that combine two luminescence processes with a different chromaticity and a diverse excita-tion range. Therefore, a continuous and reversible switching between both processes can be executed by variation of the excitation wavelength. For the synthesis of luminomagnetic materials, superparamagnetic Fe3O4/SiO2 micro-particles were modified with a variety of lanthanide containing MOFs that differ in terms of their luminescence properties and their water and air stability. For this purpose, the MOFs 2∞[Ln2Cl6(Bipy)3]·2Bipy (Bipy = 4,4’-Bipyridine, Ln = Nd, Sm, Eu, Tb, Er), 3∞[Eu(Im)2], 3∞[Ba0.95Eu0.05(Im)2] (Im- = imidazolate) and 3∞[Eu2(BDC)3]·2DMF·2H2O were employed for microparticle functionalization. By variation of the selected MOF or a combination of two different compounds, the luminescence properties of the composite materials could be adjusted in the whole visible spectral region as well as in the NIR region. The synthesized luminomagnetic composite materials with water sensitive MOFs can be applied for the detection of water in various organic solvents. Therefore, such compo-sites can be used as alternative to the Karl-Fischer titration that is easy applicable, mo-bile and exhibits similar detection limits. The composite materials 2∞[Eu2Cl6(Bipy)3]· 2Bipy@Fe3O4/SiO2 and 2∞[Eu2Cl6(Bipy)3]·2Bipy,2∞[Tb2Cl6(Bipy)3]·2Bipy@Fe3O4/SiO2 can be deployed as optical turn-off sensors, while the composite system 3∞[Eu2(BDC)3]· 2DMF·2H2O,2∞[Tb2Cl6(Bipy)3]·2Bipy@Fe3O4/SiO2 is suitable for a ratiometric determina-tion of the water content. As alternative to spherical particles, anisotropic rod-like Fe3O4/SiO2 microparticles were functionalized with 3∞[Eu2(BDC)3]·2DMF·2H2O. The resulting composite material com-bines the isotropic luminescence of the MOF shell with the anisotropic reflection of visible light of the microparticle component. A continuous and reversible switching between both optical properties is enabled by the variation of the excitation wavelength and the direction of an external magnetic field. The mechanochemical reaction of the MOF precursors [LnCl3(Py)4]·0.5Py (Ln = Eu, Ho) and 4,4’-bipyridine leads to a variety of lanthanide containing complexes and coordina-tion polymers that have already been reported in literature. Thus, a novel and time effi-cient synthesis route could be described for an alternative preparation of these com-pounds. The dimensionality of the resulting substances can be influenced in dependence on different reaction parameters that have an influence on the application of energy by the ball mill. KW - Photolumineszenz KW - Metallorganisches Netzwerk KW - Superparamagnetismus KW - Mikropartikel KW - Nanopartikel KW - Kompositmaterialien KW - Lumineszenzsensor KW - Luminomagnetische Partikel Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-158186 ER - TY - THES A1 - Rückert, Martin Andreas T1 - Rotationsdriftspektroskopie T1 - Rotational Drift Spectroscopy N2 - Die wachsende Verfügbarkeit von magnetischen Nanopartikeln (MNPs) mit funktionalisierten Partikeloberflächen eröffnet weitreichende Möglichkeiten für chemische, biologische und klinische Analysemethoden. Durch Funktionalisierung kann eine gezielte Interaktion mit Molekülen bewirkt werden, die im Allgemeinen auch die Beweglichkeit der MNPs verändern. Methoden zur Charakterisierung von MNPs wie bspw. AC-Suszeptometrie, Magnetorelaxometrie (MRX) oder Magnetic Particle Spectroscopy (MPS) können diese Änderung der Beweglichkeit bei MNPs messen, wenn es sich um MNPs handelt, deren magnetisches Moment im Partikel fixiert ist. Damit ist mit funktionalisierten MNPs indirekt auch die spezifische Messung von Molekülkonzentrationen möglich. MNPs können zudem in biokompatibler Form hergestellt werden und sind dadurch auch als in-vivo Marker einsetzbar. Das 2005 das erste Mal veröffentlichte Magnetic Particle Imaging (MPI) kann als ein mittels Gradientenfeldern um die räumliche Kodierung erweitertes MPS betrachtet werden. Dank biokompatibler MNPs handelt es sich dabei um eine in-vivo-taugliche, nicht-invasive Bildgebungsmethode. Mit funktionalisierten MNPs als Marker ist damit im Prinzip auch molekulare Bildgebung möglich, die durch Detektion der beteiligten Moleküle (Biomarker) Stoffwechselprozesse räumlich abbilden kann. Im Vergleich zur Bildgebung von Gewebe- und Knochenstrukturen lassen sich die diagnostischen Möglichkeiten durch molekulare Bildgebung erheblich erweitern. Rotationsdriftspektroskopie (Rotational Drift Spectroscopy, RDS) ist eine in dieser Arbeit entwickelte Methode für die induktive Messung der Beweglichkeit von MNPs in flüssiger Suspension. Es verwendet die Rotationsdrift von MNPs in rotierenden magnetischen Feldern als Grundlage und bietet das Potential die Änderungen der Beweglichkeit von MNPs mit einer Empfindlichkeit messen zu können, welche potentiell um mehrere Größenordnungen höher sein kann als mit den oben erwähnten Verfahren. Die vorliegende Arbeit konzentriert sich auf die Verwendbarkeit dieses Effekts als Spektroskopiemethode. Die Eigenschaften des RDS-Signals sind jedoch auch als Grundlage für räumliche Kodierung vielversprechend. In weiterführenden Projekten soll daher auch die Entwicklung von Rotationsdriftbildgebung (Rotating Drift Imaging, RDI) als ein nicht-invasives Verfahren für molekulare Bildgebung angestrebt werden. Der Grundgedanke von RDS entlehnt sich aus einem in 2006 veröffentlichten Sensordesign basierend auf magnetische Mikropartikel in einem schwachen rotierenden Magnetfeld. Das rotierende Magnetfeld ist dabei so schwach gewählt, dass sich das Partikel aufgrund der viskosen Reibung nicht mehr synchron mit dem externen Feld drehen kann. Die Frequenz der resultierenden asynchronen Rotationsdrift liegt unterhalb der Frequenz des externen Rotationsfelds und ist Abhängig von der viskosen Reibung. Aufgrund dieser Abhängigkeit können Änderungen im Reibungskoeffizienten des Partikels über Änderungen in der Rotationsdriftfrequenz gemessen werden. RDS zielt darauf ab, diese Rotationsdrift bei suspendierten MNPs über deren makroskopische Magnetisierung messen zu können. Damit wird u.a. auch die nicht-invasive Messung von MNPs innerhalb opaker biologischer Proben möglich. MNP-Suspensionen sind großzahlige Nanopartikel-ensembles und können nicht wie ein einzelnes Mikropartikel gemessen werden. Für die induktive Messung ist vor dem Start eine Ausrichtung aller magnetischen Momente nötig, da sich deren makroskopische Magnetisierung andernfalls zu Null addiert. Aufgrund von Rotationsdiffusion bleibt diese Ausrichtung nur eine begrenzte Zeit bestehen, so dass auch die eigentliche Messung des RDS-Signals nur eine begrenzte Zeit möglich ist. Diese Ausrichtung wurde in den ersten Experimenten durch einen kurzen Magnetfeldpuls erzeugt. In der Empfangsspule ist die Induktion durch das Rotationsfeld typischer Weise um mehrere Größenordnungen höher als das zu erwartende Signal und muss durch einen Tiefpass unterdrückt werden. In diesem Tiefpassfilter ruft jedoch die Einkopplung des Anfangspulses eine Pulsantwort hervor, die ebenso mehrere Größenordnungen des zu erwartenden Signals betragen kann und ähnlich langsam wie typische Signale abklingt. Die Unterdrückung dieser Pulsantwort stellte in den ersten Experimenten die größte Hürde da. Der erste Aufbau hatte eine Relaisschaltung zur Pulsunterdrückung und resultierte in einer Totzeit von 3 ms zwischen Anfangspuls und Start der Messung. Aufgrund dieser Totzeit waren die ersten Messungen auf größere Agglomerate und Sedimente von MNPs beschränkt, da nur in diesem Fall eine hinreichend lange Zerfallsdauer der Probenmagnetisierung vorlag. Das Verhalten derartiger Partikelsysteme ist jedoch aufgrund von mechanischer und magnetischer Interpartikelwechselwirkung vergleichsweise komplex und theoretisch schwer modellierbar. Das primäre Zielsystem für RDS hingegen, Eindomänenpartikel mit im Partikel fixierter Magnetisierung und Punktsymmetrie bzgl. des Reibungstensors, erlaubt die Aufstellung einer parametrisierten Funktion für den Signalverlauf. Es ermöglicht somit aufgrund der besseren Berechenbarkeit eine solidere Auswertung des RDS-Signals. Um Eindomänenpartikel in wässriger Suspension mit typischen Partikeldurchmessern um 100 nm messen zu können ist eine Verkürzung der Totzeit auf mindestens 1/10 erforderlich. Prinzipiell kann diese Problematik durch die Verwendung schneller Halbleiterschalter in Verbindung mit einer präzise abstimmbaren induktiven Entkopplung des Spulensystems gemindert werden. Simulationen des RDS-Signals für verschiedene RDS-Sequenzen zeigen jedoch noch zwei weitere Möglichkeiten auf, die ohne aufwändigen Eingriffe in der Hardware auskommen. Zum einen kann durch orthogonales Frequenzmischen mit geeignetem Frequenz- und Phasenverhältnis eine Ausrichtung der magnetischen Momente bewirkt werden. Da die benötigten Frequenzen vollständig im Sperrband des Tiefpassfilters liegen können, lässt sich damit die Pulsantwort bei hinreichend „weichem“ Umschalten zwischen der Polarisierungssequenz und der RDS-Sequenz vollständig vermeiden. Darüber hinaus zeigt sich, dass es bei Anwesenheit eines schwachen Offsetfelds (< 10 % der Rotationsfeldamplitude) zu einer Ausrichtung der magnetischen Momente kommt, wenn das magnetische Rotationsfeld seine Richtung ändert und diese Änderung nicht abrupt erfolgt, sondern das Rotationsfeld übergangsweise in ein linear oszillierendes Feld übergeht. Hingegen wird die Wirkung des Offsetfelds durch das Rotationsfeld vor und nach dem Wechsel nahezu vollständig neutralisiert, so dass damit das Störsignale generierende Schalten eines Offsetfelds ersetzt werden kann. Es ist auf diese Weise nicht möglich, Echosequenzen zu erzeugen, da hier bei der für Echosequenzen benötigten Richtungsumkehr des Rotationsfelds die zuvor aufgeprägte Phasenverteilung durch das Offsetfeld zerstört wird und somit anstelle einer Signalechogenerierung eine neue RDS-Messung gestartet wird. Obwohl es Echosequenzen mit Anfangspuls erlauben, mehr MNP Parameter zu messen, bietet dieser Ansatz dennoch entscheidende Vorteile. So ergibt sich eine massive Vereinfachung der Hardware und es sind bei gleicher Rotationsfrequenz deutlich höhere Wiederholraten möglich. Die Vermeidung von Schaltvorgängen durch die Verwendung von Offsetfeldern ermöglicht es, mit dem ursprünglichem Aufbau auch Partikelsysteme zu untersuchen, deren Relaxationszeit weit unter 3 ms liegt. Hier zeigt sich, dass sich für unterschiedliche Partikelsysteme teils sehr charakteristische Signalmuster ergeben. Diese lassen sich grob in drei Kategorien einteilen. Die erste Kategorie sind suspendierte Eindomänenpartikel mit einer nicht vernachlässigbaren Relaxationszeit. Hier handelt es sich um das bevorzugte Zielsystem für RDS, das durch die Langevin-Gleichung beschrieben werden kann. Die zweite Kategorie sind Partikelsysteme, bei denen die Relaxationsdauer vernachlässigbar ist. In diesem Fall kann der Signalverlauf mit der Langevinfunktion beschrieben werden. Die dritte Kategorie umfasst alle übrigen Partikelsysteme, insbesondere Suspensionen von MNP-Clustern, die u.a. aufgrund von Interpartikelwechselwirkung komplexe Signalverläufe ergeben, die sich praktisch nicht berechnen lassen. Spektroskopische Untersuchungen sind damit dennoch durch das Anlegen entsprechender Referenzdatenbanken möglich (Fingerprinting). Multiparametrisches RDS, d.h. die Wiederholung der Messung für z.B. unterschiedliche Amplituden oder unterschiedliche Viskositäten des Suspensionsmediums, erzeugt aufgrund mehrerer nichtlinearer Abhängigkeiten massive Unterschiede im resultierenden multidimensionalen Datensatz. Das verspricht die Erreichbarkeit hoher spektroskopischer Trennschärfen bei geeigneter Partikel- und Sequenzoptimierung. Die Simulationen und experimentellen Ergebnisse dieser Arbeit zeigen grundsätzliche Hürden und Möglichkeiten für das ebenfalls in dieser Arbeit eingeführte RDS auf. Es zeigt damit grundlegende Aspekte auf, die für die Entwicklung von RDS-Hardware und die Optimierung von MNP-Suspensionen nötig sind. Mit RDS wird in weiterführenden Arbeiten die Entwicklung von hochempfindlichen Bioassays und die Erweiterung um die räumliche Kodierung angestrebt (RDI), da der zugrunde liegende Effekt zugleich sehr vielversprechend als Grundlage für molekulare Bildgebung ist. N2 - The growing availability of magnetic nanoparticles (MNPs) with functionalized particle surfaces opens up far-reaching possibilities for chemical, biological and clinical analytical methods. Functionalization can cause targeted interaction with molecules, which generally also change the mobility of MNPs. Methods for characterizing MNPs such as AC-susceptometry, magnetorelaxometry (MRX), or magnetic particle spectroscopy (MPS) can measure this change in mobility in MNPs if they are MNPs whose magnetic moment is fixed in the particle. Thus, functionalized MNPs can indirectly be used to specifically measure molecular concentrations. MNPs can also be produced in biocompatible form, making them useful as in vivo markers. Magnetic Particle Imaging (MPI), first published in 2005, can be viewed as an MPS extended by spatial coding using gradient fields. Thanks to biocompatible MNPs, it is an in vivo, non-invasive imaging method. With functionalized MNPs as markers, molecular imaging is thus in principle also possible, which can spatially map metabolic processes by detecting the molecules involved (biomarkers). Compared to imaging of tissue and bone structures, the diagnostic possibilities can be considerably extended by molecular imaging. Rotational drift spectroscopy (RDS) is a method developed in this work for inductively measuring the mobility of MNPs in liquid suspension. It uses the rotational drift of MNPs in rotating magnetic fields as a basis and offers the potential to measure the changes in the mobility of MNPs with a sensitivity that can potentially be several orders of magnitude higher than the methods mentioned above. The present work focuses on the applicability of this effect as a spectroscopy method. However, the properties of the RDS signal are also promising as a basis for spatial coding. Therefore, in further projects, the development of Rotating Drift Imaging (RDI) as a non-invasive method for molecular imaging will also be pursued. The basic idea of RDS is borrowed from a sensor design published in 2006 based on magnetic microparticles in a weak rotating magnetic field. The rotating magnetic field is chosen so weak that the particle cannot rotate synchronously with the external field due to viscous friction. The frequency of the resulting asynchronous rotational drift is below the frequency of the external rotating field and is dependent on the viscous friction. Due to this dependence, changes in the friction coefficient of the particle can be measured via changes in the rotational drift frequency. RDS aims to be able to measure this rotational drift in suspended MNPs via their macroscopic magnetization. Among other things, this will enable the non-invasive measurement of MNPs within opaque biological samples. MNP suspensions are large number nanoparticle ensembles and cannot be measured like a single microparticle. For inductive measurement, alignment of all magnetic moments is necessary before starting, otherwise their macroscopic magnetization adds up to zero. Due to rotational diffusion, this alignment remains only for a limited time, so that the actual measurement of the RDS signal is also possible only for a limited time. This alignment was created in the first experiments by a short magnetic field pulse. In the receiving coil, the induction due to the rotating field is typically several orders of magnitude higher than the expected signal and must be suppressed by a low-pass filter. In this low-pass filter, however, the injection of the initial pulse elicits a pulse response that can likewise be several orders of magnitude of the expected signal and decays similarly slowly to typical signals. Suppression of this pulse response was the major hurdle in the initial experiments. The initial setup had a relay circuit for pulse suppression and resulted in a dead time of 3 ms between the initial pulse and the start of the measurement. Due to this dead time, the first measurements were limited to larger agglomerates and sediments of MNPs, since only in this case there was a sufficiently long decay time of the sample magnetization. However, the behavior of such particle systems is comparatively complex and difficult to model theoretically due to mechanical and magnetic interparticle interactions. In contrast, the primary target system for RDS, single domain particles with magnetization fixed in the particle and point symmetry with respect to the friction tensor, allows the establishment of a parameterized function for the signal course. Thus, it allows a more solid evaluation of the RDS signal due to its better computability. In order to measure single domain particles in aqueous suspension with typical particle diameters around 100 nm, a reduction of the dead time to at least 1/10 is required. In principle, this problem can be mitigated by using fast semiconductor switches in conjunction with precisely tunable inductive decoupling of the coil system. Simulations of the RDS signal for various RDS sequences, however, reveal two other possibilities that do not require extensive intervention in the hardware. First, orthogonal frequency shuffling with suitable frequency and phase ratios can be used to cause alignment of the magnetic moments. Since the required frequencies can lie entirely within the stopband of the low-pass filter, this allows the pulse response to be completely avoided with sufficiently "soft" switching between the polarization sequence and the RDS sequence. Furthermore, it is shown that in the presence of a weak offset field (< 10 % of the rotating field amplitude), there is an alignment of the magnetic moments when the rotating magnetic field changes direction and this change does not occur abruptly, but the rotating field transitions to a linear oscillating field. On the other hand, the effect of the offset field is almost completely neutralized by the rotating field before and after the change, so that the switching of an offset field, which generates interference signals, can thus be replaced. It is not possible to generate echo sequences in this way, since here the previously imposed phase distribution is destroyed by the offset field when the direction of the rotation field is reversed, which is required for echo sequences, and thus a new RDS measurement is started instead of signal echo generation. Although echo sequences with an initial pulse allow more MNP parameters to be measured, this approach still offers decisive advantages. For example, there is a massive simplification of the hardware and significantly higher repetition rates are possible at the same rotation frequency. The avoidance of switching processes by using offset fields makes it possible to investigate particle systems with relaxation times far below 3 ms with the original setup. Here it is shown that for different particle systems partly very characteristic signal patterns result. These can be roughly divided into three categories. The first category is suspended single domain particles with a non- negligible relaxation time. This is the preferred target system for RDS, which can be described by the Langevin equation. The second category is particle systems where the relaxation time is negligible. In this case, the signal response can be described by the Langevin function. The third category includes all other particle systems, in particular suspensions of MNP clusters, which, due to interparticle interactions, among other things, yield complex signal courses that cannot be calculated in practice. Spectroscopic investigations are nevertheless possible by creating corresponding reference databases (fingerprinting). Multiparametric RDS, i.e. repeating the measurement for e.g. different amplitudes or different viscosities of the suspension medium, generates massive differences in the resulting multidimensional data set due to several nonlinear dependencies. This promises the achievability of high spectroscopic discriminatory power with suitable particle and sequence optimization. The simulations and experimental results of this work highlight fundamental hurdles and opportunities for RDS, which is also introduced in this work. It thus highlights fundamental aspects necessary for the development of RDS hardware and the optimization of MNP suspensions. With RDS, further work will aim to develop highly sensitive bioassays and extend them to include spatial encoding (RDI), as the underlying effect is at the same time very promising as a basis for molecular imaging. KW - Magnetteilchen KW - Nanopartikel KW - Spektroskopie KW - Magnetpartikelspektroskopie KW - magnetic nanoparticles KW - rotating magnetic field Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-268631 ER - TY - THES A1 - Schummer, Bernhard T1 - Stabilisierung von CdS Nanopartikeln mittels Pluronic P123 T1 - Stabilization of CdS nanoparticles using Pluronic P123 N2 - Ziel dieser Arbeit war die Stabilisierung von Cadmiumsulfid CdS mit Pluronic P123, einem Polymer. CdS ist ein Halbleiter, der zum Beispiel in der Photonik und bei optischen Anwendungen eingesetzt wird und ist deshalb äußerst interessant, da seine Bandlücke als Nanopartikel verschiebbar ist. Für die Photovoltaik ist es ein attraktives Material, da es im sichtbaren Licht absorbiert und durch die Bandlückenverschiebung effektiver absorbieren kann. Dies ist unter dem Namen Quantum Size Effekt bekannt. Als Feststoff ist CdS für einen solchen Anwendungsbereich weniger geeignet, zumal der Effekt der Bandlückenverschiebung dort nicht auftritt. Wissenschaftler bemühen sich deshalb CdS als Nanopartikeln zu stabilisieren, weil CdS in wässrigen Lösungen ein stark aggregierendes System, also stark hydrophob ist. Es wurden zwei Kriterien für die erfolgreiche Stabilisierung von CdS festgelegt. Zum einen muss das Cds homogen im Medium verteilt sein und darf nicht agglomerieren. Zum anderen, müssen die CdS Nanopartikel kleiner als 100 A sein. In meiner Arbeit habe ich solche Partikel hergestellt und stabilisiert, d.h. verhindert, dass die Partikel weiterwachsen und gleichzeitig ihre Bandlücke verschoben wird. Die Herausforderung liegt nicht in der Herstellung, aber in der Lösung von CdS im Trägerstoff, da CdS in den meisten Flüssigkeiten nicht löslich ist und ausfällt. Die Stabilisierung in wässrigen Lösungen wurde das erste Mal durch Herrn Prof. Dr. Rempel mit Ethylendiamintetraessigsäure EDTA erfolgreich durchgeführt. Mit EDTA können jedoch nur sehr kleine Konzentrationen stabilisiert werden. Zudem können Parameter wie Größe und Geschwindigkeit der Reaktion beim Stabilisieren der CdS-Nanopartikel nicht angepasst oder beeinflusst werden. Dieses Problem ist dem, vieler medizinischer Wirkstoffe sehr ähnlich, die in hohen Konzentrationen verabreicht werden sollen, aber nicht oder nur schwer in Wasser löslich sind (Bsp. Kurkumin). Ein vielversprechender Lösungsweg ist dort, die Wirkstoffe in große Trägerpartikel (sog. Mizellen) einzuschleusen, die ihrerseits gut löslich sind. In meiner Arbeit habe ich genau diesen Ansatz für CdS verfolgt. Als Trägerpartikel/Mizelle wurde das bekannte Copolymer Pluronic P123 verwendet. Aus dieser Pluronic Produktreihe wird P123 gewählt, da es die größte Masse bei gleichzeitig höchstem Anteil von Polypropylenoxid PPO im Vergleich zur Gesamtkettenlänge hat. P123 ist ein ternäres Polyether oder Dreiblockkopolymer und wird von BASAF industriell produziert. Es besteht aus drei Böcken, dem mittlere Block Polypropylenoxid PPO und den beiden äußeren Blöcken Polyethylenoxid PEO. Der Buchstabe P steht für pastös, die ersten beiden Ziffern in P123 mit 300 multipliziert ergeben das molare Gewicht und die letzte Ziffer mit 10 multipliziert entspricht dem prozentualen Gewichtsanteil PEO. Die Bildung von Mizellen aus den P123 Molekülen kann bewusst über geringe Temperaturänderungen gesteuert werden. Bei ungefähr Raumtemperatur liegen Mizellen vor, die sich bei höheren Temperaturen von sphärischen in wurmartige Mizellen umwandeln. Oberhalb einer Konzentration von 30 Gewichtsprozent wtp bilden die Mizellen außerdem einen Flüssigkristall. Ich habe in meiner Arbeit zunächst P123 mit Hilfe von Röntgenstreuung untersucht. Anders als andere Methoden gibt Röntgenstreuung direkten Aufschluss über die Morphologie der Stoffe. Röntgenstreuung kann die Mischung von P123 mit CdS abbilden und lässt darauf schließen, ob das Ziel erreicht werden konnte, stabile CdS Nanopartikel in P123 zu binden. Für die Stabilisierung der Nanopartikel ist es zunächst notwendig die richtigen Temperaturen für die Ausgangslösungen und gemischten Lösungen zu finden. Dazu muss P123 viel genauer untersucht werden, als der momentane Kenntnisstand in der Literatur. Zu diesem Zweck als auch für die Analyse des stabilisierten CdS habe ich ein neues Instrument am LRM entwickelt, sowie eine temperierbare Probenumgebung für Flüssigkeiten fürs Vakuum, um morphologische Eigenschaften aus Streuamplituden und -winkeln zu entschlüsseln. Diese Röntgenstreuanlage wurde konzipiert und gebaut, um auch im Labor P123 in kleinen Konzentrationen messen zu können. Röntgenkleinwinkelstreuung eignet sich besonders als Messmethode, da die Probe mit einer hohen statistischen Relevanz in Flüssigkeit und in verschiedenen Konzentrationen analysiert werden kann. Für die Konzentrationen 5, 10 und 30 wtp konnte das temperaturabhängige Verhalten von P123 präzise mit Röntgenkleinwinkelstreuung SAXS gemessen und dargestellt werden. Für 5 wtp konnten die Größen der Unimere und Mizellen bestimmt werden. Trotz der nicht vorhandenen Absolutkalibration für diese Konzentration konnten dank des neu eingeführten Parameters kappa eine Dehydrierung der Mizellen mit steigender Temperatur abgeschätzt, sowie eine Hysterese zwischen dem Heizen und Abkühlen festgestellt werden. Für die Konzentration von 10 wtp wurden kleinere Temperaturschritte gewählt und die Messungen zusätzlich absolut kalibriert. Es wurden die Größen und Streulängendichten SLD der Unimere und Mizellen präzise bestimmt und ein vollständiges Form-Phasendiagramm erstellt. Auch für diese Konzentration konnte eine Hysterese eindeutig an der Größe, SLD und am Parameter kappa gezeigt werden, sowie eine Dehydrierung des Mizellenkerns. Dies beweist, dass der Parameter kappa geeignet ist, um bei nicht absolut kalibrierten Messungen, Aussagen über die Hydrierung und Hysterese komplexer Kern-Hülle Modelle zu machen. Für die Konzentration von 30 wtp konnte zwischen 23°C und 35°C eine FCC Struktur nachgewiesen werden. Dabei vergrößert sich die Gitterkonstante der FCC Struktur von 260 A auf 289 A in Abhängigkeit der Temperatur. Durch das Mischen zweier Lösungen, zum einen CdCl2 und 30 wtp P123 und zum anderen Na2S und 30 wtp P123, konnte CdS erfolgreich stabilisiert werden. Mit einer Kamera wurde die Gelbfärbung der Lösung, und somit die Bildung des CdS, in Abhängigkeit der Zeit untersucht. Es konnte festgestellt werden, dass das Bilden der CdS Nanopartikel je nach Konzentration und Temperierprogramm zwischen 30 und 300 Sekunden dauert und einer logistischen Wachstumsfunktion folgt. Höhere Konzentrationen CdS bewirken einen schnelleren Anstieg der Wachstumsfunktion. Mittels UV-Vis Spektroskopie konnte gezeigt werden, dass die Bandlücke von CdS mit steigender Konzentration konstant bei 2,52 eV bleibt. Eine solche Verschiebung der Bandlücke von ungefähr 0,05 eV im Vergleich zum Festkörper, deutet auf einen CdS Partikeldurchmesser von 80A hin. Mit SAXS konnte gezeigt werden, dass sich die flüssigkristalline Struktur des P123 bei zwei verschiedenen Konzentrationen CdS, von 0,005 und 0,1 M, nicht ändert. Das CdS wird zwischen den Mizellen, also durch die Bildung des Flüssigkristalls, und im Kern der Mizelle aufgrund seiner Hydrophobizität stabilisiert. Die Anfangs definierten Kriterien für eine erfolgreiche Stabilisierung wurden erfüllt. P123 ist ein hervorragend geeignetes Polymer, um hydrophobes CdS, sowohl durch die Bildung eines Flüssigkristalls, als auch im Kern der Mizelle zu stabilisieren. N2 - Aim of this work was the stabilization of cadmium sulphide CdS with Pluronic P123, a polymer. CdS is a semiconductor, which is used for photonics and for optical applications. It is highly interesting since its band gap can be shifted if it has the size of a nanoparticle. Due to this band gap shift and the fact that CdS is absorbing in the visible range, it is highly attractive material. This is known as the quantum size effect. As a solid, CdS is less interesting in this area because of the non-existing band gap shift. Scientists endeavor to stabilize CdS as a nanoparticle, since CdS is hydrophobic in aqueous solutions and thus a strongly aggregating system. Two criteria of a successful stabilization process were set. Firstly, CdS has to be homogeneously distributed in the solution and must not aggregate. Secondly, the nanoparticles must be smaller then 100A. During my thesis I produced such particles and stabilized them homogeneously in an aqueous solution, which meant to hinder the further growth of those nanopaticles while shifting their band gap. The challenge is not the production, but the encapsulation of CdS in a carrier, since CdS is not soluble in most solutions and precipitates. Such a stabilization in an aqueous solution was succeeded by Prof. Dr. Rempel with ethylenediaminetetraacetic acid EDTA as a stabilizer for the first time. But with EDTA only very small concentrations of CdS can be stabilized. Moreover, properties like size and reaction speed during the stabilization of the CdS nanoparticles cannot be adjusted or influenced. This problem is also known from medical agents, which should be administered in high doses, but are not or barely soluble in water like Curcumin. A promising solution is to encapsulate these medical agents in big carrier, so-called micelles, which themselves are soluble in water. In my thesis I followed this approach for CdS. As a carrier/micelle the well known copolymer Pluronic P123 was used. Compared to other Pluronics, P123 was chosen since it offers the biggest mass with the highest proportion of polypropylene oxide PPO compared to the total chain length. P123 is a ternary polyether and is produced industrially by BASF. It consists of three blocks, where the middle one is PPO and the outer blocks are polyethylene oxide PEO. The letter P stands for pasty while the first two numbers in P123 multiplied with 300 equal the molar mass and the last number multiplied with 10 equals the mass proportion of PEO. The formation of micelles can be triggered on purpose with a change in temperature. Micelles are present at approximately room temperature \cite{Manet2011}, which transform from spherical to worm-like micelles at higher temperatures. Above a certain concentration of 30 weight percent, the micelles will form a liquid crystal. In my work I first examined P123 with X-ray scattering. Unlike other methods, X-ray scattering gives direct information about the morphology of the substances. X-ray scattering can also be used to study the mixture of P123 with CdS and indicates, whether the goal of encapsulate stable CdS nanoparticles in P123 could be achieved. To stabilize the nanoparticles, it is first necessary to find the right temperatures for both the staring point and the end point of the stabilization process. For this purpose, P123 has to be examined much more precisely than the current state of knowledge in the literature. For this purpose as well as for the analysis of the stabilized CdS, I have developed a new instrument at the chair of X-ray microscopy, as well as a temperature controllable sample holder for liquids in vacuum to decipher morphological properties from scattering amplitudes and angles. This X-ray scattering system was designed and built in order to be able to measure P123 in small concentrations in the laboratory. Small-angle X-ray scattering is particularly suitable as a measurement method, since the sample can be analyzed with a high statistical relevance in liquid and in various concentrations. For the concentrations 5, 10 and 30 wtp, the temperature-dependent behavior of P123 could be precisely measured and presented using small-angle X-ray scattering. The sizes of the unimers and micelles could be determined for 5 wtp without an absolute calibration. With a newly introduced parameter kappa, the dehydration of the micelles with increasing temperature could be estimated, despite the lack of the absolute calibration for this concentration, as well as a hysteresis between heating and cooling. Smaller temperature steps were chosen for the concentration of 10 wtp, furthermore the measurements were also absolutely calibrated. The sizes and scattering length densities SLDs of the unimers and micelles were precisely determined and a complete shape-phase diagram was created. Also for this concentration, a hysteresis was clearly shown in terms of size, SLD and the parameter kappa, as well as dehydration of the micellar nucleus. This proves that the parameter kappa is suitable for making statements about the hydrogenation and hysteresis of complex core-shell models in the case of measurements that are not absolutely calibrated. For the concentration of 30 wtp an FCC structure could be detected between 23°C and 35°C. The lattice constant of the FCC structure increases from 260 A to 289 A depending on the temperature. By mixing two solutions, CdCl2 in a 30 wtp P123 and Na2S in 30 wtp P123, CdS could be successfully stabilized. The yellow coloration of the solution, and thus the formation of CdS, was examined as a function of time with the help of a camera. It was found that the formation of the CdS nanoparticles takes between 30 and 300 seconds, depending on the concentration and temperature protocol and follows a logistical growth function. Higher concentrations of CdS cause a more rapid increase in growth function. Using UV-Vis spectroscopy it could be shown that the band gap of CdS remains constant at 2.52 eV with increasing concentration. The shift in the band gap of approximately 0.05 eV compared to the solid state, indicates a CdS particle diameter of 80 A. With SAXS it could be shown that the liquid-crystalline structure of the P123 does not change at two different concentrations of CdS, of 0.005 and 0.1 M. The CdS is stabilized between the micelles due to the formation of the liquid crystal and in the core of the micelles due to their hydrophobicity. The initially defined criteria for successful stabilization were met. P123 is an excellent polymer to stabilize hydrophobic CdS nanoparticles, both through the formation of a liquid crystal and in the core of the micelles. KW - Röntgen-Kleinwinkelstreuung KW - Polymere KW - Cadmiumsulfid KW - Röntgen-Weitwinkelstreuung KW - Nanopartikel KW - Stabilisierung Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-238443 ER - TY - THES A1 - Dembski, Sofia Viktorovna T1 - Synthese und Charakterisierung von II-VI-Halbleiter-Nanopartikeln in unterschiedlicher Umgebung T1 - Synthesis and Characterization of II-VI-Semiconductor Nanoparticles in Selected Environment N2 - Gegenstand dieser Arbeit ist die Synthese und Charakterisierung von II-VI-Halbleiter-Nanopartikeln (NP) in unterschiedlicher Umgebung. Aufgrund des großen Oberfläche-zu-Volumen-Verhältnisses werden Partikeleigenschaften stark durch ihre Oberfläche und die Wechselwirkung mit der Umgebung beeinflusst. Zuerst wurden strukturierte CdSe und CdSe/ZnS-Kern-Schale Nanopartikel durch eine organometallische Synthese in koordinierenden Lösungsmitteln hergestellt. Die optischen und elektronischen Eigenschaften wurden mittels Absorptions-(UV/VIS)-, Fluoreszenz- und konfokaler Fluoreszenz-Korrelations-Spektroskopie (FCS) untersucht. Die Ermittlung der Kristallstruktur erfolgte durch hochauflösende Transmissionselektronenmikroskopie (HRTEM) und Röntgenpulverdiffraktometrie (XRD). Die experimentellen XRD Resultate wurden durch Simulationen mittels der Debye-Formel sowie Berechnung einer Paarverteilungsfunktion (PDF) für die verschiedenen Nanopartikel-Modelle ausgewertet. Somit konnten die Partikelgröße, -form und die Kristallstruktur ermittelt werden. Ramanspektroskopische Untersuchungen ergaben Informationen über die Zusammensetzung des anorganischen Partikelkerns sowie seiner stabilisierenden Ligandenhülle. Aufbauend auf diesen Ergebnissen aus unterschiedlichen spektroskopischen und mikroskopischen Methoden konnte ein Struktur-Modell für die Kern-Schale Nanopartikel entwickelt werden. Dabei ist ein prolater wurtzitischer CdSe-Kern mit einer segmentartigen, lückenhaften ZnS-Schale beschichtet, die eine Zinkblende-Struktur aufweist. Zur Untersuchung der Umgebungseffekte wurden die CdSe- und CdSe/ZnS-Halbleiter-NP mit hydrophilen Liganden funktionalisiert, reversibel mit einer Polymerhülle beschichtet sowie kontrolliert in Silica-Kolloide eingebettet (Multikernpartikel). Somit konnten die Nanopartikel in unterschiedlich polaren und apolaren Lösungsmitteln stabilisiert und charakterisiert werden. Im Hinblick auf die Anwendungen von Halbleiter-NP als Marker in den Lebenswissenschaften wurde die Biokompatibilität und die lichtinduzierte Fluoreszenzverstärkung von Polymer-beschichteten II-VI-Halbleiter-NP und CdSe/ZnS-dotierten Silica-Kolloiden in unterschiedlichen Umgebungen untersucht. Mit Hilfe der erhaltenen Resultate ist ein neues qualitatives Modell für die lichtinduzierten Aktivierungs- und Desaktivierungsprozesse in Multikernpartikeln entwickelt worden. Ein weiterer Aspekt dieser Arbeit war die Untersuchung der lokalen elektronischen Struktur von II-VI-Halbleiter-NP in unterschiedlichen Umgebungen durch elementspezifische Anregung mit weicher Röntgenstrahlung. Dazu wurde ein Verfahren weiterentwickelt, das es erlaubt, einzelne gespeicherte feste und flüssige Nanopartikel substratfrei mit Hilfe von Synchrotronstrahlung zu analysieren. Darüber hinaus wurde die Röntgenabsorptionsfeinstruktur von deponierten CdSe/ZnS-dotierten Silica-Kolloiden durch die Messung der röntgenangeregten optischen Fluoreszenz (XEOL) bzw. durch die Bestimmung der totalen Elektronenausbeute (TEY) untersucht. N2 - Subject of this thesis is the synthesis and characterization of II-VI-semiconductor nanoparticles (quantum dots, QD) in selected environments. Structured CdSe and CdSe/ZnS core-shell nanoparticles have been prepared by syntheses that are based on the high temperature thermolysis of organometallic precursors in the presence of stabilizing agents. The influence of the local environment on the optical properties of the QD is studied by optical absorption (UV/VIS), photoluminescence, and confocal fluorescence correlation spectroscopy (FCS). The crystal structure of the nanoparticles is characterized by high-resolution electron microscopy (HRTEM) and X-ray diffraction (XRD). The diffraction patterns are fitted directly by modeling the nanocrystals using the Debye equation and pair distribution function (PDF), which models the interatomic distances within the sample. These results allowed us to determine fundamental parameters, such as size, shape, and crystal structure. Raman spectroscopy probes the lattice vibrations of the nanocrystals. This approach is applied to investigate the composition of the core-shell particles and especially to study the bonding between the stabilizing ligands and the nanoparticle surface by analyzing the internal vibrational modes. The results of the several characterization methods allowed us to develop a new model for the core-shell particle structure: ZnS with a zincblende structure forms an irregularly shaped shell around the elongated CdSe core which has a wurtzite structure. Further, the particles are subsequently functionalized either by an exchange of their ligands, or by the reversible adsorption of an amphiphilic polymer. Alternatively, they are embedded in silica colloids in a controlled way (multicore particles). As a result, the nanoparticle properties can be studied in various solvents ranging from apolar to polar liquids as well as in solid environments. Moreover, multicore particles have the potential to be used as selective labels for biological studies. Therefore, the cytotoxicity and the light induced enhancement of the luminescence of the multicore particles in various environments are investigated. Based on the present results, a new qualitative model for the mechanism of the photoactivation and -deactivation of CdSe/ZnS dotted silica colloids in various solvents is developed. The local electronic structure of the QD is studied by element-specific excitation using soft X-rays. For this purpose, a recently developed approach has been improved, allowing the investigation of single solid and liquid particles trapped in an electrodynamic particle trap, which are probed by monochromatic synchrotron radiation. In addition, the near edge X-ray absorption fine structure of deposited CdSe/ZnS doped silica colloids is determined by the measurement of the X-ray excited optical luminescence (XEOL) and the total electron yield (TEY). KW - Zwei-Sechs-Halbleiter KW - Nanopartikel KW - II-VI-Halbleiter-Nanopartikel KW - Umgebungseffekte KW - Oberflächenmodifizierung KW - Multikernpartikel KW - Fluoreszenzverstärkung KW - Röntgenabsorptionsfeinstruktur KW - II-VI-semiconductor nanoparticles KW - quantum dots KW - environmental effects KW - surface modifications KW - multicore particles KW - photoactivation KW - NEXAFS Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-22066 ER - TY - THES A1 - Beringer, Reiner Ernst T1 - Synthese von Dextran-umhüllten Eisenoxid-Nanopartikeln als Kontrastmittel für die MR-Tomographie T1 - Synthesis of dextran-coated iron oxide nanoparticles as contrast agent for MRI N2 - Durch Fällung von Eisen(II)- und Eisen(III)-salzen wurden Dextran-umhüllte Eisenoxid-Nanopartikel (SPIOs) und durch anschließende Umsetzung mit Epichlorhydrin und Ammoniak CLIOs gewonnen. An diesen Kolloiden wurden niedermolekulare Moleküle wie Diamine oder Bernsteinsäureanhydrid als Linker angebracht. Ein weiterer Aspekt dieser Arbeit stellt die Anbindung von Fluoreszenzmarkern und Antikörpern an der Partikeloberfläche sowie deren spektroskopische Untersuchung dar. N2 - By precipitation of iron (II) - and iron (III) salts dextran-coated iron oxide were nanoparticles (SPIOs) synthesized and CLIOs were generated by reaction with epichlorohydrin and ammonia. At these colloids low molecular weight molecules such as diamines or succinic anhydride were placed as a linker. Another aspect of this work is the integration of fluorescent markers and antibodies on the particle surface and spectroscopic investigation of these colloids. KW - Eisenoxide KW - Magnetische Resonanz KW - NMR-Tomographie KW - Nanopartikel KW - Dextrane KW - Kontrastmittel KW - Eisenoxid-Nanopartikel KW - SPIO KW - CLIO KW - Kontrastmittel KW - iron oxide nanoparticles KW - MR contrast agent KW - SPIO KW - CLIO Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-77218 ER - TY - THES A1 - Blömer, Steffen T1 - Synthese von modifizierten Eisenoxid-Nanopartikeln für die MR-Tomographie T1 - Synthesis of modified iron oxide nanoparticles for MRI N2 - In der vorliegenden Arbeit wurden magnetische Kolloide auf der Basis von Eisenoxid-Nanopartikeln hergestellt, die eine erhöhte Verweildauer im Blutstrom aufweisen sollten. Die Hüllmoleküle bestehen aus zwei Teilen: Direkt an den Phosphor gebunden eine hydrophobe Alkylkette aus vier bis zehn CH2-Einheiten, und daran anschließend eine Methoxy-terminierte Polyethylenglykol (PEG)-Kette. Die PEG-Kette sollte sowohl die Hydrophilie der fertigen Partikel als auch den nötigen Schutz gegen Phagozytose gewährleisten. Diese speziellen Phosphonsäuren wurden dann dazu verwendet, Magnetit-Nanopartikel stabil einzuhüllen. N2 - The present dissertation deals with the preparation of magnetic colloids on the basis of iron oxide nanoparticles exhibiting an extended lifetime in the bloodstream. The coating molecules were made up of two parts: A hydrophobic alkyl chain of four to ten CH2 groups, and a methoxy-terminated polyethyleneglycol (PEG) chain. The PEG chain was included to make the particles hydrophilic and to protect them from phagocytosis. These specially designed phosphonic acids were then used to coat magnetite nanoparticles. KW - Eisenoxide KW - Nanopartikel KW - NMR-Tomographie KW - Kontrastmittel KW - Polyethylenglykole KW - Magnetresonanztomographie KW - PEG KW - iron oxide KW - nanoparticles KW - MRI KW - contrast agent Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-66068 ER - TY - THES A1 - Heydt, Silke T1 - Synthese von Nanopartikeln und der Einfluss ihrer Primärpartikelgröße auf die Fließregulierung von idealen und nicht-idealen Schüttgütern T1 - Synthesis of nanoparticles and the influence of their primary particle size on the flow regulation of ideal and non-ideal bulk materials N2 - Die Fließfähigkeit eines pharmazeutischen Schüttguts spielt insbesondere bei der Herstellung von volumendosierten Arzneiformen, wie beispielsweise Tabletten, eine große Rolle. Häufig kommen deshalb sogenannte Fließregulierungsmittel zum Einsatz, um eine ausreichende Fließfähigkeit zu gewährleisten. Der Prozess der Fließregulierung kann mit einer Abnahme der van der Waals Kräfte zwischen den einzelnen Schüttgutpartikeln beschrieben werden. Diese Reduktion der Haftkraft beruht auf der Anlagerung von Adsorbaten des Fließregulierungsmittels an die Oberfläche der Trägerpartikel. Im Rahmen der Arbeit sollten sowohl die Einflussfaktoren des Schüttguts als auch die des Fließregulierungsmittels auf den Prozess der Fließregulierung geprüft werden. Es wurde gezeigt, dass die Morphologie eines Schüttguts großen Einfluss auf den Prozess der Fließregulierung besitzt. Je glatter die Oberfläche eines Schüttguts ist, desto weniger Fließregulierungsmittel wird ungenutzt eingelagert. Es steht demzufolge mehr Fließregulierungsmittel als Abstandshalter zwischen den einzelnen Schüttgutpartikeln zur Verfügung, was wiederum zu einer Reduktion der van der Waals Kräfte und somit zur Fließverbesserung führt. Ein weiterer Schwerpunkt lag auf der Beurteilung des Einflusses der Primärpartikelgröße eines Fließregulierungsmittels auf seine fließregulierende Potenz. Hierzu wurden Kieselsäurenanopartikel synthetisiert, die sich lediglich in ihren Primärpartikelgrößen unterscheiden. Mit Hilfe des Sol-Gel-Prozesses innerhalb einer Mikroemulsion wurden prozesssicher diskrete, sphärische und einheitliche Kieselsäurenanopartikel in einem Größenbereich von 8 nm bis 100 nm erhalten. Um den Einfluss der Primärpartikelgröße zu prüfen, wurden die Schüttgüter Maisstärke und Lactose mit den synthetisierten Kieselsäuren versetzt und in einem Turbula-Mischer gemischt. Die Beurteilung der Potenz der Fließregulierungsmittel in Kombination mit dem jeweiligen Schüttgut erfolgte mittels Messungen am Zugspannungstester. Für beide Schüttgüter wurde eine eindeutige Korrelation zwischen der Primärpartikelgröße und der Potenz des Fließregulierungsmittels festgestellt, wobei je nach Schüttgutmorphologie unterschiedliche Ergebnisse für die optimale Primärpartikelgröße des Fließregulierungsmittels erhalten wurden. Die Auswahl eines Fließregulierungsmittels sollte demnach unter Beachtung seiner Primärpartikelgröße in Anpassung an die Schüttgutbeschaffenheit erfolgen. Somit kann der Fließregulierungsprozess zukünftig systematischer gestaltet werden. N2 - The flowability of a pharmaceutical powder plays a major role, especially in the production of volume-dosed dosage forms like tablets. Therefore, often so called flow regulators are used to ensure sufficient fluidity. The process of flow regulation can be described by a decrease of van der Waals forces between individual bulk particles. This reduction of adhesion strength is due to the addition of adsorbates of the flow control agent to the surface of the carrier particles. In the context of this work the influence factors of the bulk material as well as the flow control agent on the process of flow regulation should be examined. It was shown that the morphology of a bulk material has great influence on the process of flow regulation. The smoother the surface of a bulk material, the less flow-regulator is stored unused. Therefore, more flow control agent is available that acts as a spacer between the bulk particles leading to a reduction of the van der Waals forces and an improvement of the flowability. Another focus was on assessing the influence of the primary particle size of a flow control agent on its flow regulating potency. For this purpose, silica nanoparticles were synthesized, which differ only in their primary particle sizes. Using the sol-gel process within a micro-emulsion it was possible to produce reliably discrete, spherical and uniform silica nanoparticles in a size range of 8 to 100 nm. To examine the influence of the primary particle size, the synthesized silicas were added to corn starch and lactose and then mixed in a turbula mixer. The evaluation of the potency of the flow-regulating agents in combination with the respective bulk material was performed by measurements with a tensile strength tester. For both bulk materials a clear correlation between the primary particle size and the potency of a flow regulating agent was found. Different results for an optimal primary particle size of the flow control agent were obtained depending on the bulk morphology. Therefore, the selection of a flow control agent should be made in accordance with its primary particle size depending on the bulk composition. Thus, the flow-regulating process should be more systematically in the future. KW - Nanopartikel KW - Fließverhalten KW - Pulver KW - Schüttgut KW - Mikroemulsion KW - Zugspannung KW - Fließregulierung KW - Nanopartikelsynthese KW - flow regulation KW - microemulsion KW - nanoparticle synthesis Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-67489 ER - TY - THES A1 - Rettenmaier, Jürgen T1 - Synthese von TiO2-Nanopartikeln und Carbazol-Farbstoffderivaten für optische Anwendungen in anorganisch-organischen Hybridpolymeren T1 - Synthesis of TiO2 nanoparticles and dye derivatives of Carbazole for optical applications in anorganic-organic hybrid polymers N2 - Die Arbeit hatte das Ziel, Beiträge zur Synthese photorefraktiver Nanokomposite durch die geschickte Kombination spezieller organischer Farbstoffe mit elektronenleitenden, anorganischen Nanopartikeln oder mit lochleitenden Carbazol-Derivaten in hybriden Polymeren zu leisten. Dabei wurden grundlegende Erkenntnisse auf folgenden Gebieten erzielt: > TiO2-Nanopartikel als anorganische Elektronenleiter > Carbazol-Derivate als organische Lochleiter > Metallkomplex-Farbstoffe als Photosensibilisatoren > Optisch nichtlineare Chromophore > Struktur-Eigenschafts-Beziehungen in hybriden Materialien > Photoleitung > Optische Nichtlinearität N2 - Aim of the thesis was to achieve fundamental knowledge on following fields. This could be approched by smart combination of organic dyes with electron conducting inorganic nanoparticles or with hole conducting Carbazole derivates incorporated in hybrid polymers. > TiO2 Nanoparticles as inorganic semiconductors by electron transfer > Carbazole derivates as organic photoconductors operating through hole mobility > Metal complex chromophores as photosensitizers > Second-order nonlinear optical chromophores > Relation between structure and characteristics of hybrid materials > Photoconductivity > Optical nonlinearity KW - Photorefraktiver Effekt KW - Nanopartikel KW - Azofarbstoff KW - Titandioxid KW - Carbazolderivate KW - Metallorganische Polymere KW - NLO KW - SHG KW - optische Nichtlinearität 2. Ordnung KW - nicht-lineare Optik KW - Photorefraktiver Effekt KW - Photoleitfähigkeit KW - Titandioxid KW - Nanopartikel KW - NLO KW - SHG KW - optical nonlinearity 2. order KW - non-linear optics KW - photorefractivity KW - photoconductivity KW - Titaniumdioxide KW - Nanoparticles KW - Carbazole Y1 - 2002 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-2937 ER - TY - THES A1 - Wolf, Nadine T1 - Synthese, Charakterisierung und Modellierung von klassischen Sol-Gel- und Nanopartikel-Funktionsschichten auf der Basis von Zinn-dotiertem Indiumoxid und Aluminium-dotiertem Zinkoxid T1 - Synthesis, characterization and modeling of classical sol gel and nanoparticle functional layers on the basis of indium tin oxide and alumnium zinc oxide N2 - Das Ziel dieser Arbeit ist neben der Synthese von Sol-Gel-Funktionsschichten auf der Basis von transparent leitfähigen Oxiden (transparent conducting oxides, TCOs) die umfassende infrarotoptische und elektrische Charakterisierung sowie Modellierung dieser Schichten. Es wurden sowohl über klassische Sol-Gel-Prozesse als auch über redispergierte Nanopartikel-Sole spektralselektive Funktionsschichten auf Glas- und Polycarbonat-Substraten appliziert, die einen möglichst hohen Reflexionsgrad im infraroten Spektralbereich und damit einhergehend einen möglichst geringen Gesamtemissionsgrad sowie einen niedrigen elektrischen Flächenwiderstand aufweisen. Zu diesem Zweck wurden dotierte Metalloxide, nämlich einerseits Zinn-dotiertes Indiumoxid (tin doped indium oxide, ITO) und andererseits Aluminium-dotiertes Zinkoxid (aluminum doped zinc oxide, AZO)verwendet. Im Rahmen dieser Arbeit wurden vertieft verschiedene Parameter untersucht, die bei der Präparation von niedrigemittierenden ITO- und AZO-Funktionsschichten im Hinblick auf die Optimierung ihrer infrarot-optischen und elektrischen Eigenschaften sowie ihrer Transmission im sichtbaren Spektralbereich von Bedeutung sind. Neben der Sol-Zusammensetzung von klassischen Sol-Gel-ITO-Beschichtungslösungen wurden auch die Beschichtungs- und Ausheizparameter bei der Herstellung von klassischen Sol-Gel-ITO- sowie -AZO-Funktionsschichten charakterisiert und optimiert. Bei den klassischen Sol-Gel- ITO-Funktionsschichten konnte als ein wesentliches Ergebnis der Arbeit der Gesamtemissionsgrad um 0.18 auf 0.17, bei in etwa gleichbleibenden visuellen Transmissionsgraden und elektrischen Flächenwiderständen, reduziert werden, wenn anstelle von (optimierten) Mehrfach-Beschichtungen Einfach-Beschichtungen mit einer schnelleren Ziehgeschwindigkeit anhand des Dip-Coating-Verfahrens hergestellt wurden. Mit einer klassischen Sol-Gel-ITO-Einfach-Beschichtung, die mit einer deutlich erhöhten Ziehgeschwindigkeit von 600 mm/min gedippt wurde, konnte mit einem Wert von 0.17 der kleinste Gesamtemissionsgrad dieser Arbeit erzielt werden. Die Gesamtemissionsgrade und elektrischen Flächenwiderstände von klassischen Sol-Gel-AZOFunktionsschichten konnten mit dem in dieser Arbeit optimierten Endheizprozess deutlich gesenkt werden. Bei Neunfach-AZO-Beschichtungen konnten der Gesamtemissionsgrad um 0.34 auf 0.50 und der elektrische Flächenwiderstand um knapp 89 % auf 65 Ω/sq verringert werden. Anhand von Hall-Messungen konnte darüber hinaus nachgewiesen werden, dass mit dem optimierten Endheizprozess, der eine erhöhte Temperatur während der Reduzierung der Schichten aufweist, mit N = 4.3·1019 cm-3 eine etwa doppelt so hohe Ladungsträgerdichte und mit µ = 18.7 cm2/Vs eine etwa drei Mal so große Beweglichkeit in den Schichten generiert wurden, im Vergleich zu jenen Schichten, die nach dem alten Endheizprozess ausgehärtet wurden. Das deutet darauf hin, dass bei dem optimierten Heizschema sowohl mehr Sauerstofffehlstellen und damit eine höhere Ladungsträgerdichte als auch Funktionsschichten mit einem höheren Kristallisationsgrad und damit einhergehend einer höheren Beweglichkeit ausgebildet werden. Ein Großteil der vorliegenden Arbeit behandelt die Optimierung und Charakterisierung von ITO-Nanopartikel-Solen bzw. -Funktionsschichten. Neben den verwendeten Nanopartikeln, dem Dispergierungsprozess, der Beschichtungsart sowie der jeweiligen Beschichtungsparameter und der Nachbehandlung der Funktionsschichten, wurde erstmals in einer ausführlichen Parameterstudie die Sol-Zusammensetzung im Hinblick auf die Optimierung der infrarot-optischen und elektrischen Eigenschaften der applizierten Funktionsschichten untersucht. Dabei wurde insbesondere der Einfluss der verwendeten Stabilisatoren sowie der verwendeten Lösungsmittel auf die Schichteigenschaften charakterisiert. Im Rahmen dieser Arbeit wird dargelegt, dass die exakte Zusammensetzung der Nanopartikel-Sole einen große Rolle spielt und die Wahl des verwendeten Lösungsmittels im Sol einen größeren Einfluss auf den Gesamtemissionsgrad und die elektrischen Flächenwiderstände der applizierten Schichten hat als die Wahl des verwendeten Stabilisators. Allerdings wird auch gezeigt, dass keine pauschalen Aussagen darüber getroffen werden können, welcher Stabilisator oder welches Lösungsmittel in den Nanopartikel-Solen zu Funktionsschichten mit kleinen Gesamtemissionsgraden und elektrischen Flächenwiderständen führt. Stattdessen muss jede einzelne Kombination von verwendetem Stabilisator und Lösungsmittel empirisch getestet werden, da jede Kombination zu Funktionsschichten mit anderen Eigenschaften führt. Zudem konnte im Rahmen dieser Arbeit erstmals stabile AZO-Nanopartikel-Sole über verschiedene Rezepte hergestellt werden. Neben der Optimierung und Charakterisierung von ITO- und AZO- klassischen Sol-Gel- sowie Nanopartikel-Solen und -Funktionsschichten wurden auch die infrarot-optischen Eigenschaften dieser Schichten modelliert, um die optischen Konstanten sowie die Schichtdicken zu bestimmen. Darüber hinaus wurden auch kommerziell erhältliche, gesputterte ITO- und AZO-Funktionsschichten modelliert. Die Reflexionsgrade dieser drei Funktionsschicht-Typen wurden einerseits ausschließlich mit dem Drude-Modell anhand eines selbstgeschriebenen Programmes in Sage modelliert, und andererseits mit einem komplexeren Fit-Modell, welches in der kommerziellen Software SCOUT aus dem erweiterten Drude-Modell, einem Kim-Oszillator sowie dem OJL-Modell aufgebaut wurde. In diesem Fit-Modell werden auch die Einflüsse der Glas-Substrate auf die Reflexionsgrade der applizierten Funktionsschichten berücksichtigt und es können die optischen Konstanten sowie die Dicken der Schichten ermittelt werden. Darüber hinaus wurde im Rahmen dieser Arbeit ein Ellipsometer installiert und geeignete Fit-Modelle entwickelt, anhand derer die Ellipsometer-Messungen ausgewertet und die optischen Konstanten sowie Schichtdicken der präparierten Schichten bestimmt werden können. N2 - The aim of this thesis is on the one hand the synthesis of sol-gel functional layers on the basis of transparent conducting oxides (TCOs) and on the other hand a comprehensive infrared-optical and electrical characterization as well as modeling of these layers. Spectrally selective coatings have been prepared with the classical sol-gel route as well as with redispersed nanoparticle sols on glass and polycarbonate substrates and these coatings should have a reflectance in the infrared spectral range which is as high as possible and therefore a total emittance and an electrical sheet resistance which are as small as possible. For this purpose tin doped indium oxide (ITO) and aluminum doped zinc oxide (AZO) have been used as doped metal oxides. Within this thesis several parameters have been investigated in-depth which play a decisive role in the preparation of ITO and AZO low emissivity coatings, in order to prepare such coatings with optimized infrared-optical and electrical properties as well as visual transmittances. Besides the composition of the classical sol-gel ITO coating solutions, also the parameters of the coating as well as the heating processes have been characterized and optimized in the manufacture of classical sol-gel ITO and AZO functional layers. As a significant result the total emittance of classical sol-gel ITO functional layers could be reduced by 0.18 to 0.17 while the visual transmittance and electrical sheet resistances stay approximately the same, if just one-layered coatings are applied with a higher withdrawal speed with the dip coating technique instead of (optimized) multi-layered coatings. With a classical sol-gel ITO single coating, which has been produced with a withdrawal speed of 600 mm/min, the smallest total emittance of this work could be realized with 0.17. The total emittances and electrical sheet resistances of classical sol-gel AZO functional layers were reduced drastically in this work by using the optimized final heating process. The total emittance could be reduced by 0.34 to 0.50 and the electrical sheet resistance by 89 % to 65Ω/sq with a coating which consists of nine single layers. On the basis of Hall measurements it has been shown that coatings which were treated with the optimized heating process (which exhibits a higher temperature during the reducing treatment of the coatings) show a higher charge carrier density as well as a higher mobility than those coatings treated with the old heating process. With the optimized heating process the ninelayered coatings exhibit a charge carrier density of N = 4.3·1019 cm-3 which is approximately twice as high and a mobility of µ = 18.7 cm2/Vs which is about three times higher than the values of coatings which have been heated with the old process. This indicates that with the optimized heating process more oxygen vacancies and, associated therewith a higher charge carrier density as well as a higher crystallinity of the layer and thus a higher mobility are generated. One focus of the presented work lies on the optimization and characterization of ITO redispersed nanoparticle sols and functional layers respectively. In addition to the used nanoparticles, the dispersion process, the coating type with the respective coating parameters and post-treatments of the functional layers also a detailed parameter study has been done. This parameter study examined the composition of the nanoparticle sols with a view to the optimization of the infrared-optical and electrical properties of the applied coatings. The coating properties have been studied in particularly with regard to the influence of the used stabilizers and solvents respectively. In this work it will be shown, that the accurate composition of the nanoparticle sols plays a decisive role and the choice of the used solvents has a bigger impact on the coating properties than the choice of the used stabilizers. However, it will also be shown, that no general statements can be made which stabilizers or which solvents within the sols lead to coatings which have small total emittances and small electrical sheet resistances. Instead each combination of used stabilizer and used solvent has to be empirically tested since each combination leads to coatings with different properties. Furthermore stable AZO nanoparticle sols based on several formulas have been developed for the first time. Besides the optimization and characterization of ITO and AZO classical sol-gel as well as nanoparticle sols and functional layers, also the infrared-optical properties of these coatings have been modeled in order to determine the optical constants as well as the coating thicknesses. Furthermore also commercially available sputtered ITO and AZO coatings have been modeled. The reflectances of these three types of coatings have been modeled on the one hand by using only the Drude model within a self-written program in the software Sage. On the other hand these coatings have been modeled with more complex fitting models within the commercially available software called SCOUT. These more complex fitting models consist of the extended Drude model, a Kim oscillator and an OJL model and they also take the influence of the glass substrates on the reflectances of the applied coatings into account. By using these fitting models, the optical constants of the applied coatings and the coating thicknesses can be obtained. In addition an Ellipsometer has been installed as part of this work and suitable fitting models have been developed. These models can be used for analyzing the Ellipsometer measurements in order to determine the optical constants and the coating thicknesses of the coatings applied. KW - Transparent-leitendes Oxid KW - Sol-Gel-Verfahren KW - Beschichtung KW - Funktionswerkstoff KW - Sol-Gel-Synthese KW - ITO KW - AZO KW - redispergierte Nanopartikel-Sole KW - Drude-Modell KW - sol gel KW - redispersed nanoparticle sol KW - Drude model KW - Charakterisierung KW - Modellierung KW - Physikalische Schicht KW - Nanopartikel Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-112416 ER - TY - THES A1 - Eber, Marcus T1 - Wirksamkeit und Leistungsfähigkeit von nanoskaligen Fließregulierungsmitteln T1 - Effectiveness and efficiency of nanoscale glidants N2 - Zusammenfassend stellen sich die hydrophoben Nanomaterialien als die optimalen Fließregulierungsmittel dar (Ausnahme: Printex® G). Die Agglomerate des hochpotenten hydrophoben Ruß-Derivats Printex® 95 liegen von Herstellerseite bereits in genügend zerkleinerter Form vor, so daß keine weitere Zerkleinerung während des Mischvorganges erforderlich ist. Infolgedessen adsorbiert es mit höchster Geschwindigkeit an die Oberfläche der Schüttgutpartikel und übernimmt dort die Funktion von Oberflächenrauhigkeiten. In der Folge der werden die interpartikulären Haftkräfte sehr schnell minimiert. Im Gegensatz zu den hydrophilen Nanomaterialien zeigt Printex® 95 keinen ausgeprägten Wiederanstieg der Zugspannungen selbst nach sehr langen Mischzeiten von 4320 Minuten. Durch die Verwendung des hydrophoben Ruß-Derivates Printex® 95 werden Pulvermischungen erhalten, die zudem weitestgehend unempfindlich sind gegenüber Kapillarkräften bei erhöhten Umgebungsfeuchten. Das hydrophobe Printex® 95 vereint damit praktisch alle gewünschten Eigenschaften eines optimalen Fließregulierungsmittels und es kann als Modellsubstanz für die Entwicklung noch potenterer Nanomaterialien dienen. Bisher stand das nicht abschließend beurteilte cancerogene Potential dieses Stoffes einer breiten Anwendung entgegen. N2 - Summing up it can be said that hydrophobic nanomaterials are highly potent glidants (with exception of Printex® G). The agglomerates of the top-rated hydrophobic Printex® 95 are already small enough because of the manufacturing process, so that they do not have to be broken up during the mixing process. As a consequence, Printex® 95 is adsorbed most quickly on the surface of corn starch to fulfill the function of surface asperities. Because of this increasing surface roughness the interparticle forces are rapidly diminished. In contrast to all the hydrophilic nanomaterials, Printex® 95 does not show a pronounced re-increase in tensile strength even after a blending time of 4320 minutes. Moreover the binary powder mixtures with Printex® 95 are very robust against capillary forces at higher moisture levels. Altogether, it can combine all the requested demands for a top-rated glidant and may also serve as a model nanomaterial in order to develop further glidants. So far it could not be applied broadly since its cancerigenous potential has not been finally evaluated. KW - Nanostrukturiertes Material KW - Hydrophobe Wechselwirkung KW - Fließverhalten KW - Schüttgut KW - AFM KW - Fließfähigkeit KW - intermolekulare Kräfte KW - Nanopartikel KW - SPM KW - flowability KW - intermolecular forces KW - nanoparticles Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-9026 ER - TY - THES A1 - Wagner, Martin T1 - Zyto- und Gentoxizität von Zinkoxid-Nanopartikeln in humanen mesenchymalen Stammzellen nach repetitiver Exposition und im Langzeitversuch T1 - Time-Dependent Toxic and Genotoxic Effects of Zinc Oxide Nanoparticles after Long-Term and Repetitive Exposure to Human Mesenchymal Stem Cells N2 - Zinkoxid-Nanopartikel (ZnO-NP) finden in vielen Produkten des täglichen Verbrauchs Verwendung. Daten über die toxikologischen Eigenschaften von ZnO-NP werden kontrovers diskutiert. Die menschliche Haut ist in Bezug auf die ZnO-NP Exposition das wichtigste Kontakt-Organ. Intakte Haut stellt eine suffiziente Barriere gegenüber NP dar. Bei defekter Haut ist ein Kontakt zu den proliferierenden Stammzellen möglich, sodass diese als wichtiges toxikologische Ziel für NP darstellen. Das Ziel dieser Dissertation war die Bewertung der genotoxischen und zytotoxischen Effekte an humanen mesenchymalen Stammzellen (hMSC) durch niedrig dosierte ZnO-NP nach 24 stündiger Exposition, repetitiven Expositionen und im Langzeitversuch bis zu 6 Wochen. Zytotoxische Wirkungen von ZnO-NP wurden mit 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazoliumbromid-Test (MTT) gemessen. Darüber hinaus wurde die Genotoxizität durch den Comet-Assay bewertet. Zur Langzeitbeobachtung bis zu 6 Wochen wurde die Transmissionselektronenmikroskopie (TEM) verwendet. Zytotoxizität nach 24-stündiger ZnO-NP-Exposition war ab einer Konzentration von 50 µg/ml nachweisbar. Genotoxizität konnten bereits bei Konzentrationen von 1 und 10 µg/ml ZnO-NP beschrieben werden. Wiederholte Exposition verstärkte die Zyto-, aber nicht die Genotoxizität. Eine intrazelluläre NP-Akkumulation mit Penetration der Zellorganelle wurde bei einer Exposition bis zu 6 Wochen beobachtet. Die Ergebnisse deuten auf zytotoxische und genotoxisches Effekte von ZnO-NP hin. Bereits geringe Dosen von ZnO-NP können bei wiederholter Exposition toxische Wirkungen hervorrufen sowie eine langfristige Zellakkumulation. Diese Daten sollten bei der Verwendung von ZnO-NP an geschädigter Haut berücksichtigt werden. N2 - Zinc oxide nanoparticles (ZnO-NP) are widely used in many products of daily consumption. Data on the toxicological properties of the ZnO-NP used are discussed controversially. Human skin is the most important organ in terms of ZnO-NP exposure. Intact skin has been shown to provide an adequate barrier against NPs, while defective skin allows NP contact with proliferating cells. Among proliferating cells, stem cells are the main toxicological target for NPs. Therefore, the aim of this dissertation was to evaluate the genotoxic and cytotoxic effects of human mesenchymal stem cells (hMSC) by low-dose ZnO-NP after 24 hours of exposure, repetitive exposures and in long-term experiments up to 6 weeks. Cytotoxic effects of ZnO-NP were measured with 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide test (MTT). In addition, genotoxicity was assessed by the comet assay. Transmission electron microscopy (TEM) was used for long-term observation after 6 exposure periods. The results of the study show that ZnO-NP has a cytotoxic effect starting at high concentrations of 50 µg/mL and could demonstrate genotoxic effects in hMSC exposed to 1 and 10 µg/ml ZnO-NP. Repeated exposure enhanced cytotoxicity but not genotoxicity. Intracellular NP accumulation with penetration of the cell organelles was observed at exposure up to 6 weeks. The results indicate the cytotoxic and genotoxic potential of ZnO-NP. Even small doses of ZnO-NP can cause toxic effects with repeated exposure and long-term cell accumulation. These data should be considered when using ZnO-NP on damaged skin. KW - nanoparticle KW - zinc oxid KW - stem cells KW - nanotoxicology KW - human skin KW - Nanopartikel KW - humane mesenchymale Stammzellen KW - Genotoxizität KW - Zytotoxizität KW - Repetitive Exposition KW - Elektronenmikroskopie Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-275726 ER -