TY - JOUR A1 - Bothe, Friederike A1 - Deubel, Anne-Kathrin A1 - Hesse, Eliane A1 - Lotz, Benedict A1 - Groll, Jürgen A1 - Werner, Carsten A1 - Richter, Wiltrud A1 - Hagmann, Sebastien T1 - Treatment of focal cartilage defects in minipigs with zonal chondrocyte/mesenchymal progenitor cell constructs JF - International Journal of Molecular Sciences N2 - Despite advances in cartilage repair strategies, treatment of focal chondral lesions remains an important challenge to prevent osteoarthritis. Articular cartilage is organized into several layers and lack of zonal organization of current grafts is held responsible for insufficient biomechanical and biochemical quality of repair-tissue. The aim was to develop a zonal approach for cartilage regeneration to determine whether the outcome can be improved compared to a non-zonal strategy. Hydrogel-filled polycaprolactone (PCL)-constructs with a chondrocyte-seeded upper-layer deemed to induce hyaline cartilage and a mesenchymal stromal cell (MSC)-containing bottom-layer deemed to induce calcified cartilage were compared to chondrocyte-based non-zonal grafts in a minipig model. Grafts showed comparable hardness at implantation and did not cause visible signs of inflammation. After 6 months, X-ray microtomography (µCT)-analysis revealed significant bone-loss in both treatment groups compared to empty controls. PCL-enforcement and some hydrogel-remnants were retained in all defects, but most implants were pressed into the subchondral bone. Despite important heterogeneities, both treatments reached a significantly lower modified O’Driscoll-score compared to empty controls. Thus, PCL may have induced bone-erosion during joint loading and misplacement of grafts in vivo precluding adequate permanent orientation of zones compared to surrounding native cartilage. KW - cartilage repair KW - osteochondral defect KW - tissue engineering KW - starPEG hydrogel KW - chondrocyte KW - MSC KW - zonal construct KW - minipig Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-285118 SN - 1422-0067 VL - 20 IS - 3 ER - TY - JOUR A1 - Rödel, Michaela A1 - Teßmar, Jörg A1 - Groll, Jürgen A1 - Gbureck, Uwe T1 - Tough and Elastic alpha-Tricalcium Phosphate Cement Composites with Degradable PEG-Based Cross-Linker JF - Materials N2 - Dual setting cements composed of an in situ forming hydrogel and a reactive mineral phase combine high compressive strength of the cement with sufficient ductility and bending strength of the polymeric network. Previous studies were focused on the modification with non-degradable hydrogels based on 2-hydroxyethyl methacrylate (HEMA). Here, we describe the synthesis of suitable triblock degradable poly(ethylene glycol)-poly(lactide) (PEG-PLLA) cross-linker to improve the resorption capacity of such composites. A study with four different formulations was established. As reference, pure hydroxyapatite (HA) cements and composites with 40 wt% HEMA in the liquid cement phase were produced. Furthermore, HEMA was modified with 10 wt% of PEG-PLLA cross-linker or a test series containing only 25% cross-linker was chosen for composites with a fully degradable polymeric phase. Hence, we developed suitable systems with increased elasticity and 5-6 times higher toughn ess values in comparison to pure inorganic cement matrix. Furthermore, conversion rate from alpha-tricalcium phosphate (alpha-TCP) to HA was still about 90% for all composite formulations, whereas crystal size decreased. Based on this material development and advancement for a dual setting system, we managed to overcome the drawback of brittleness for pure calcium phosphate cements. KW - dual setting system KW - bending strength KW - calcium phosphate cement KW - composite material KW - HEMA KW - hydroxyapatite KW - free radical polymerization Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-226437 VL - 12 IS - 53 ER - TY - JOUR A1 - Stuckensen, Kai A1 - Lamo-Espinosa, José M. A1 - Muiños-López, Emma A1 - Ripalda-Cemboráin, Purificación A1 - López-Martínez, Tania A1 - Iglesias, Elena A1 - Abizanda, Gloria A1 - Andreu, Ion A1 - Flandes-Iparraguirre, María A1 - Pons-Villanueva, Juan A1 - Elizalde, Reyes A1 - Nickel, Joachim A1 - Ewald, Andrea A1 - Gbureck, Uwe A1 - Prósper, Felipe A1 - Groll, Jürgen A1 - Granero-Moltó, Froilán T1 - Anisotropic cryostructured collagen scaffolds for efficient delivery of RhBMP−2 and enhanced bone regeneration JF - Materials N2 - In the treatment of bone non-unions, an alternative to bone autografts is the use of bone morphogenetic proteins (BMPs), e.g., BMP–2, BMP–7, with powerful osteoinductive and osteogenic properties. In clinical settings, these osteogenic factors are applied using absorbable collagen sponges for local controlled delivery. Major side effects of this strategy are derived from the supraphysiological doses of BMPs needed, which may induce ectopic bone formation, chronic inflammation, and excessive bone resorption. In order to increase the efficiency of the delivered BMPs, we designed cryostructured collagen scaffolds functionalized with hydroxyapatite, mimicking the structure of cortical bone (aligned porosity, anisotropic) or trabecular bone (random distributed porosity, isotropic). We hypothesize that an anisotropic structure would enhance the osteoconductive properties of the scaffolds by increasing the regenerative performance of the provided rhBMP–2. In vitro, both scaffolds presented similar mechanical properties, rhBMP–2 retention and delivery capacity, as well as scaffold degradation time. In vivo, anisotropic scaffolds demonstrated better bone regeneration capabilities in a rat femoral critical-size defect model by increasing the defect bridging. In conclusion, anisotropic cryostructured collagen scaffolds improve bone regeneration by increasing the efficiency of rhBMP–2 mediated bone healing. KW - rhBMP–2 KW - collagen sponge KW - cryostructured scaffolds KW - bone critical size defect Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-195966 SN - 1996-1944 VL - 12 IS - 19 ER - TY - JOUR A1 - Groll, J A1 - Burdick, J A A1 - Cho, D-W A1 - Derby, B A1 - Gelinsky, M A1 - Heilshorn, S C A1 - Jüngst, T A1 - Malda, J A1 - Mironov, V A A1 - Nakayama, K A1 - Ovsianikov, A A1 - Sun, W A1 - Takeuchi, S A1 - Yoo, J J A1 - Woodfield, T B F T1 - A definition of bioinks and their distinction from biomaterial inks JF - Biofabrication N2 - Biofabrication aims to fabricate biologically functional products through bioprinting or bioassembly (Groll et al 2016 Biofabrication 8 013001). In biofabrication processes, cells are positioned at defined coordinates in three-dimensional space using automated and computer controlled techniques (Moroni et al 2018 Trends Biotechnol. 36 384–402), usually with the aid of biomaterials that are either (i) directly processed with the cells as suspensions/dispersions, (ii) deposited simultaneously in a separate printing process, or (iii) used as a transient support material. Materials that are suited for biofabrication are often referred to as bioinks and have become an important area of research within the field. In view of this special issue on bioinks, we aim herein to briefly summarize the historic evolution of this term within the field of biofabrication. Furthermore, we propose a simple but general definition of bioinks, and clarify its distinction from biomaterial inks. KW - bioink KW - biomaterial ink KW - definition Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-253993 VL - 11 IS - 1 ER - TY - INPR A1 - Schaefer, Natascha A1 - Janzen, Dieter A1 - Bakirci, Ezgi A1 - Hrynevich, Andrei A1 - Dalton, Paul D. A1 - Villmann, Carmen T1 - 3D Electrophysiological Measurements on Cells Embedded within Fiber-Reinforced Matrigel T2 - Advanced Healthcare Materials N2 - 2D electrophysiology is often used to determine the electrical properties of neurons, while in the brain, neurons form extensive 3D networks. Thus, performing electrophysiology in a 3D environment provides a closer situation to the physiological condition and serves as a useful tool for various applications in the field of neuroscience. In this study, we established 3D electrophysiology within a fiber-reinforced matrix to enable fast readouts from transfected cells, which are often used as model systems for 2D electrophysiology. Using melt electrowriting (MEW) of scaffolds to reinforce Matrigel, we performed 3D electrophysiology on a glycine receptor-transfected Ltk-11 mouse fibroblast cell line. The glycine receptor is an inhibitory ion channel associated when mutated with impaired neuromotor behaviour. The average thickness of the MEW scaffold was 141.4 ± 5.7µm, using 9.7 ± 0.2µm diameter fibers, and square pore spacings of 100 µm, 200 µm and 400 µm. We demonstrate, for the first time, the electrophysiological characterization of glycine receptor-transfected cells with respect to agonist efficacy and potency in a 3D matrix. With the MEW scaffold reinforcement not interfering with the electrophysiology measurement, this approach can now be further adapted and developed for different kinds of neuronal cultures to study and understand pathological mechanisms under disease conditions. KW - 3D cultures Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-244194 ER - TY - JOUR A1 - No, Young Jung A1 - Holzmeister, Ib A1 - Lu, Zufu A1 - Prajapati, Shubham A1 - Shi, Jeffrey A1 - Gbureck, Uwe A1 - Zreiqat, Hala T1 - Effect of Baghdadite Substitution on the Physicochemical Properties of Brushite Cements JF - Materials N2 - Brushite cements have been clinically used for irregular bone defect filling applications, and various strategies have been previously reported to modify and improve their physicochemical properties such as strength and injectability. However, strategies to address other limitations of brushite cements such as low radiopacity or acidity without negatively impacting mechanical strength have not yet been reported. In this study, we report the effect of substituting the beta-tricalcium phosphate reactant in brushite cement with baghdadite (Ca\(_3\)ZrSi\(_2\)O\(_9\)), a bioactive zirconium-doped calcium silicate ceramic, at various concentrations (0, 5, 10, 20, 30, 50, and 100 wt%) on the properties of the final brushite cement product. X-ray diffraction profiles indicate the dissolution of baghdadite during the cement reaction, without affecting the crystal structure of the precipitated brushite. EDX analysis shows that calcium is homogeneously distributed within the cement matrix, while zirconium and silicon form cluster-like aggregates with sizes ranging from few microns to more than 50 µm. X-ray images and µ-CT analysis indicate enhanced radiopacity with increased incorporation of baghdadite into brushite cement, with nearly a doubling of the aluminium equivalent thickness at 50 wt% baghdadite substitution. At the same time, compressive strength of brushite cement increased from 12.9 ± 3.1 MPa to 21.1 ± 4.1 MPa with 10 wt% baghdadite substitution. Culture medium conditioned with powdered brushite cement approached closer to physiological pH values when the cement is incorporated with increasing amounts of baghdadite (pH = 6.47 for pure brushite, pH = 7.02 for brushite with 20 wt% baghdadite substitution). Baghdadite substitution also influenced the ionic content in the culture medium, and subsequently affected the proliferative activity of primary human osteoblasts in vitro. This study indicates that baghdadite is a beneficial additive to enhance the radiopacity, mechanical performance and cytocompatibility of brushite cement KW - baghdadite KW - calcium phosphate cement KW - radiopacity KW - setting reaction KW - mechanical performance Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-196980 SN - 1996-1944 VL - 12 IS - 10 ER - TY - JOUR A1 - Jungst, Tomasz A1 - Pennings, Iris A1 - Schmitz, Michael A1 - Rosenberg, Antoine J. W. P. A1 - Groll, Jürgen A1 - Gawlitta, Debby T1 - Heterotypic Scaffold Design Orchestrates Primary Cell Organization and Phenotypes in Cocultured Small Diameter Vascular Grafts JF - Advanced Functional Materials N2 - To facilitate true regeneration, a vascular graft should direct the evolution of a neovessel to obtain the function of a native vessel. For this, scaffolds have to permit the formation of an intraluminal endothelial cell monolayer, mimicking the tunica intima. In addition, when attempting to mimic a tunica media‐like outer layer, the stacking and orientation of vascular smooth muscle cells (vSMCs) should be recapitulated. An integral scaffold design that facilitates this has so far remained a challenge. A hybrid fabrication approach is introduced by combining solution electrospinning and melt electrowriting. This allows a tissue‐structure mimetic, hierarchically bilayered tubular scaffold, comprising an inner layer of randomly oriented dense fiber mesh and an outer layer of microfibers with controlled orientation. The scaffold supports the organization of a continuous luminal endothelial monolayer and oriented layers of vSM‐like cells in the media, thus facilitating control over specific and tissue‐mimetic cellular differentiation and support of the phenotypic morphology in the respective layers. Neither soluble factors nor a surface bioactivation of the scaffold is needed with this approach, demonstrating that heterotypic scaffold design can direct physiological tissue‐like cell organization and differentiation. KW - biofabricated vascular graft KW - heterotypic scaffold design KW - hybrid fabrication KW - primary vascular smooth muscle‐like cells (vSMCs) KW - melt electrowriting (MEW) Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-217039 VL - 29 ER - TY - JOUR A1 - Brückner, Theresa A1 - Meininger, Markus A1 - Groll, Jürgen A1 - Kübler, Alexander C. A1 - Gbureck, Uwe T1 - Magnesium Phosphate Cement as Mineral Bone Adhesive JF - Materials N2 - Mineral bone cements were actually not developed for their application as bone-bonding agents, but as bone void fillers. In particular, calcium phosphate cements (CPC) are considered to be unsuitable for that application, particularly under moist conditions. Here, we showed the ex vivo ability of different magnesium phosphate cements (MPC) to adhere on bovine cortical bone substrates. The cements were obtained from a mixture of farringtonite (Mg\(_3\)(PO\(_4\))\(_2\)) with different amounts of phytic acid (C\(_6\)H\(_{18}\)O\(_{24}\)P\(_6\), inositol hexaphosphate, IP6), whereas cement setting occurred by a chelation reaction between Mg\(^{2+}\) ions and IP6. We were able to show that cements with 25% IP6 and a powder-to-liquid ratio (PLR) of 2.0 g/mL resulted in shear strengths of 0.81 ± 0.12 MPa on bone even after 7 d storage in aqueous conditions. The samples showed a mixed adhesive–cohesive failure with cement residues on the bone surface as indicated by scanning electron microscopy and energy-dispersive X-ray analysis. The presented material demonstrated appropriate bonding characteristics, which could enable a broadening of the mineral bone cements’ application field to bone adhesives KW - magnesium phosphate cement KW - phytic acid KW - bone adhesive Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-193052 SN - 1996-1944 VL - 12 IS - 23 ER - TY - JOUR A1 - Hettich, Georg A1 - Schierjott, Ronja A. A1 - Epple, Matthias A1 - Gbureck, Uwe A1 - Heinemann, Sascha A1 - Mozaffari-Jovein, Hadi A1 - Grupp, Thomas M. T1 - Calcium phosphate bone graft substitutes with high mechanical load capacity and high degree of interconnecting porosity JF - Materials N2 - Bone graft substitutes in orthopedic applications have to fulfill various demanding requirements. Most calcium phosphate (CaP) bone graft substitutes are highly porous to achieve bone regeneration, but typically lack mechanical stability. This study presents a novel approach, in which a scaffold structure with appropriate properties for bone regeneration emerges from the space between specifically shaped granules. The granule types were tetrapods (TEPO) and pyramids (PYRA), which were compared to porous CaP granules (CALC) and morselized bone chips (BC). Bulk materials of the granules were mechanically loaded with a peak pressure of 4 MP; i.e., comparable to the load occurring behind an acetabular cup. Mechanical loading reduced the volume of CALC and BC considerably (89% and 85%, respectively), indicating a collapse of the macroporous structure. Volumes of TEPO and PYRA remained almost constant (94% and 98%, respectively). After loading, the porosity was highest for BC (46%), lowest for CALC (25%) and comparable for TEPO and PYRA (37%). The pore spaces of TEPO and PYRA were highly interconnected in a way that a virtual object with a diameter of 150 µm could access 34% of the TEPO volume and 36% of the PYRA volume. This study shows that a bulk of dense CaP granules in form of tetrapods and pyramids can create a scaffold structure with load capacities suitable for the regeneration of an acetabular bone defect KW - calcium phosphate KW - granules KW - biomechanics KW - bone graft substitutes Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-193233 SN - 1996-1944 VL - 12 IS - 21 ER - TY - JOUR A1 - Robinson, Thomas M. A1 - Hutmacher, Dietmar W. A1 - Dalton, Paul D. T1 - The next frontier in melt electrospinning: taming the jet JF - Advanced Functional Materials N2 - There is a specialized niche for the electrohydrodynamic jetting of melts, from biomedical products to filtration and soft matter applications. The next frontier includes optics, microfluidics, flexible electronic devices, and soft network composites in biomaterial science and soft robotics. The recent emphasis on reproducibly direct‐writing continual molten jets has enabled a spectrum of contemporary microscale 3D objects to be fabricated. One strong suit of melt processing is the capacity for the jet to solidify rapidly into a fiber, thus fixing a particular structure into position. The ability to direct‐write complex and multiscaled architectures and structures has greatly contributed to a large number of recent studies, explicitly, toward fiber–hydrogel composites and fugitive inks, and has expanded into several biomedical applications such as cartilage, skin, periosteum, and cardiovascular tissue engineering. Following the footsteps of a publication that summarized melt electrowriting literature up to 2015, the most recent literature from then until now is reviewed to provide a continuous and comprehensive timeline that demonstrates the latest advances as well as new perspectives for this emerging technology. KW - 3D printing KW - additive manufacturing KW - eletrhydrodynamic KW - melt electrospinning writing Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-204819 VL - 29 ER - TY - JOUR A1 - Fuchs, A. A1 - Youssef, A. A1 - Seher, A. A1 - Hochleitner, G. A1 - Dalton, P. D. A1 - Hartmann, S. A1 - Brands, R. C. A1 - Müller-Richter, U. D. A. A1 - Linz, C, T1 - Medical-grade polycaprolactone scaffolds made by melt electrospinning writing for oral bone regeneration – a pilot study in vitro JF - BMC Oral Health N2 - Background The spectrum of indications for the use of membranes and scaffolds in the field of oral and maxillofacial surgery includes, amongst others, guided bone regeneration (GBR). Currently available membrane systems face certain disadvantages such as difficult clinical handling, inconsistent degradation, undirected cell growth and a lack of stability that often complicate their application. Therefore, new membranes which can overcome these issues are of great interest in this field. Methods In this pilot study, we investigated polycaprolactone (PCL) scaffolds intended to enhance oral wound healing by means of melt electrospinning writing (MEW), which allowed for three-dimensional (3D) printing of micron scale fibers and very exact fiber placement. A singular set of box-shaped scaffolds of different sizes consisting of medical-grade PCL was examined and the scaffolds’ morphology was evaluated via scanning electron microscopy (SEM). Each prototype sample with box sizes of 225 μm, 300 μm, 375 μm, 450 μm and 500 μm was assessed for cytotoxicity and cell growth by seeding each scaffold with human osteoblast-like cell line MG63. Results All scaffolds demonstrated good cytocompatibility according to cell viability, protein concentration, and cell number. SEM analysis revealed an exact fiber placement of the MEW scaffolds and the growth of viable MG63 cells on them. For the examined box-shaped scaffolds with pore sizes between 225 μm and 500 μm, a preferred box size for initial osteoblast attachment could not be found. Conclusions These well-defined 3D scaffolds consisting of medical-grade materials optimized for cell attachment and cell growth hold the key to a promising new approach in GBR in oral and maxillofacial surgery. KW - melt electrospinning writing KW - polycaprolactone KW - scaffold KW - guided bone regeneration Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-200274 VL - 19 ER - TY - THES A1 - Bertlein, Sarah T1 - Hydrogels as Biofunctional Coatings and Thiol-Ene Clickable Bioinks for Biofabrication T1 - Hydrogele als biofunktionale Beschichtungen und Thiol-Ene-clickbare Biotinten für die Biofabrikation N2 - Ziel dieser Arbeit war die Entwicklung von funktionalisierbaren Hydrogel Beschichtungen für Schmelz-elektrogeschriebene PCL Gerüste und von Bio-druckbaren Hydrogelen für die Biofabrikation. Hydrogel Beschichtungen von Schmelz-elektrogeschriebenen Konstrukten ermöglichten die Kontrolle der Oberflächen-Hydrophilie und damit Zell-Material Interaktionsstudien in minimal Protein-adhäsiven Umgebungen. Zu diesem Zweck wurde ein hydrophiles sternförmiges vernetzbares Polymer verwendet und eine Optimierung der Beschichtungsbedingungen durchgeführt. Außerdem boten neu entwickelte photosensitive Konstrukte eine Zeit- und pH-unabhängige Biofunktionalisierung. Bio-druckbare Hydrogele für die Biofabrikation basierten auf der Allyl-Funktionalisierung von Gelatine (GelAGE) und modifizierten Hyaluronsäure-Produkten, die das Hydrogel-Vernetzen mittels Thiol-En Click Chemie ermöglichen. Die Optimierung der GelAGE Hydrogel-Eigenschaften wurde durch eine detaillierte Analyse der Syntheseparameter, variierender En:SH Verhältnisse, unterschiedlicher Vernetzungsmoleküle und Photoinitiatoren erreicht. Die Homogenität der Thiol-En Netzwerke wurde mit denen der freien radikalischen Polymerisation verglichen und die Verwendbarkeit von GelAGE als Bio-Tinte für den Extrusions-basierten Bio-Druck wurde untersucht. Es wurde angenommen, dass reine Hyaluronsäure-basierte Bio-Tinten eine Beibehaltung der mechanischen und rheologischen Eigenschaften, der Zellviabilität und der Prozessierbarkeit ermöglichen trotz geringerem Polymer- und Thiol-Anteil der Hydrogele. Hydrogel-Beschichtungen: Hoch definierte PCL Gerüste wurden mittels MEW hergestellt und anschließend mit sechs armigen sternförmigen vernetzbaren Polymeren (sP(EO-stat-PO)) beschichtet. Die Vernetzung wird durch die wässrig-induzierte Hydrolyse reaktiver Isocyanatgruppen (NCO) von sP(EO-stat-PO) bedingt. Diese Beschichtung erhöhte die Oberflächen-Hydrophilie und stellte eine Plattform für weitere Biofunktionalisierungen, in minimal Protein-adhäsiven Umgebungen, dar. Nicht nur das Beschichtungsprotokoll wurde hinsichtlich der sP(EO-stat-PO) Konzentrationen und der Beschichtungsdauern optimiert, sondern auch Vorbehandlungen der Gerüste wurden entwickelt. Diese waren essentiell um die finale Hydrophilie von sP(EO-stat-PO) beschichteten Gerüste so zu erhöhen, dass unspezifische Protein-Adhäsionen vollständig unterbunden wurden. Die sP(EO-stat-PO) Schichtdicke, von ungefähr 100 nm, ermöglicht generell in vitro Studien nicht nur in Abhängigkeit der Gerüst-Biofunktionalisierung, sondern auch in Abhängigkeit der Gerüst-Architektur durchzuführen. Das Ausmaß der Hydrogel-Beschichtung wurde mittels einer indirekten Quantifizierung der NCO-Hydrolyse-Produkte ermittelt. Kenntnis über die NCO-Hydrolyse-Kinetik ermöglichte ein Gleichgewicht zwischen ausreichend beschichteten Gerüsten und der Präsenz der NCO-Gruppen herzustellen, welche für die anschließenden Biofunktionalisierungen genutzt wurden. Diese Zeit- und pH-abhängige Biofunktionalisierung war jedoch nur für kleine Biomoleküle möglich. Um diese Beschränkung zu umgehen und auch hochmolekulare Biomoleküle kovalent anzubinden, wurde ein anderer Reaktionsweg entwickelt. Dieser basierte auf der Photolyse von Diazirin-Gruppen und ermöglichte eine Zeit- und pH-unabhängige Biofunktionalisierung der Gerüste mit Streptavidin und Kollagen Typ I. Die Fibrillen bildende Eigenschaft von Kollagen wurde genutzt um auf den Gerüsten verschiedene Kollagen-Konformationen zu erhalten und eine erste in vitro Studie bestätigte die Anwendbarkeit für Zell-Material Interaktionsstudien. Die hier entwickelten Gerüste könnten verwendet werden um tiefere Einblicke in die Grundlagen der zellulären Wahrnehmung zu erhalten. Insbesondere die Komplexität mit der Zellen z.B. Kollagen wahrnehmen bleibt weiterhin klärungsbedürftig. Hierfür könnten diverse Hierarchien von Kollagen-ähnlichen Konformationen an die Gerüste gebunden werden, z.B. Gelatine oder Kollagen-abgeleitete Peptidsequenzen. Dann könnte die Aktivierung der DDR-Rezeptoren in Abhängigkeit der Komplexität der angebundenen Substanzen bestimmt werden. Aufgrund der starken Streptavidin-Biotin Bindung könnten Streptavidin funktionalisierte Gerüste eine vielseitige Plattform für die Immobilisierung von jeglichen biotinylierten Molekülen darstellen. Gelatine-basierte Bio-Tinten: Zuerst wurden die GelAGE-Produkte hinsichtlich der Molekulargewichts-Verteilung und der Integrität der Aminosäuren-Zusammensetzung synthetisiert. Eine detailliert Studie, mit variierenden molaren Edukt-Verhältnissen und Synthese-Zeitspannen, wurde durchgeführt und implizierte, dass der Gelatine Abbau am deutlichsten für stark alkalische Synthesebedingungen mit langen Reaktionszeiten war. Gelatine beinhaltet mehrere funktionalisierbare Gruppen und anhand diverser Model-Substanzen und Analysen wurde die vorrangige Amingruppen-Funktionalisierung ermittelt. Die Homogenität des GelAGE-Polymernetzwerkes, im Vergleich zu frei radikalisch polymerisierten GelMA-Hydrogelen, wurde bestätigt. Eine ausführliche Analyse der Hydrogel-Zusammensetzungen mit variierenden funktionellen Gruppen Verhältnissen und UV- oder Vis-Licht induzierbaren Photoinitiatoren wurde durchgeführt. Die UV-Initiator Konzentration ist aufgrund der Zell-Toxizität und der potenziellen zellulären DNA-Beschädigung durch UV-Bestrahlung eingeschränkt. Das Zell-kompatiblere Vis-Initiator System hingegen ermöglichte, durch die kontrollierte Photoinitiator-Konzentration bei konstanten En:SH Verhältnissen und Polymeranteilen, die Einstellung der mechanischen Eigenschaften über eine große Spanne hinweg. Die Flexibilität der GelAGE Bio-Tinte für unterschiedliche additive Fertigungstechniken konnte, durch Ausnutzung des temperaturabhängigen Gelierungsverhaltens unterschiedlich stark degradierter GelAGE Produkte, für Stereolithographie und Extrusions-basiertem Druck bewiesen werden. Außerdem wurde die Viabilität zellbeladener GelAGE Konstrukte bewiesen, die mittels Extrusions-basiertem Bio-Druck erhalten wurden. Die Verwendung diverser multifunktioneller und makromolekularer Thiol-Vernetzungsmoleküle ermöglichte eine Verbesserung der mechanischen und rheologischen Eigenschaften und ebenso der Prozessierbarkeit. Verglichen mit dem kleinen bis-Thiol-funktionellen Vernetzungsmolekül waren geringere Thiol-Vernetzer-Konzentrationen notwendig um bessere mechanische Festigkeiten und physikochemische Eigenschaften der Hydrogele zu erhalten. Der Extrusions-basierte Bio-Druck unterschiedlicher eingekapselter Zellen verdeutlichte die Notwendigkeit der individuellen Optimierung von Zell-beladenen Hydrogel-Formulierungen. Nicht nur die Zellviabilität von eingekapselten Zellen in Extrusions-basierten biogedruckten Konstrukten sollte bewertet werden, sondern auch andere Parameter wie die Zellmorphologie oder die Kollagen- oder Glykosaminoglykan-Produktion, da diese einige der essentiellen Voraussetzungen für die Verwendung in Knorpel Tissue Engineering Konzepten darstellen. Außerdem sollten diese Studien auf die stereolithographischen Ansätze erweitert werden und letztlich wäre die Flexibilität und Zellkompatibilität der Formulierungen mit makromolekularen Vernetzern von Interesse. Makromolekulare Vernetzer ermöglichten die Reduktion des Polymeranteils und des Thiol-Gehalts und können, insbesondere in Kombination mit dem Zell-kompatibleren Vis-Initiator-System, voraussichtlich zu einer gesteigerten Zellkompatibilität beitragen, was zu klären bleibt. Hyaluronsäure-basierte Bio-Tinten: Unterschiedliche Hyaluronsäure-Produkte (HA) wurden synthetisiert, sodass diese En- (HAPA) oder Thiol-Funktionalitäten (LHASH) beinhalteten, um reine HA Thiol-En vernetzte Hydrogele zu erhalten. In Abhängigkeit des Molekulargewichts der HA-Produkte, der Polymeranteile und des En:SH Verhältnisses, konnte eine große Spanne an mechanischen Festigkeiten abgedeckt werden. Aufgrund der hohen Viskosität war allerdings im Falle von hochmolekularen HA (HHAPA) Produkt-Lösungen (HHAPA + LHASH) die Handhabbarkeit auf 5.0 wt.-% beschränkt. Die Verwendung der gleichen HA Thiol-Komponenten (LHASH) ermöglichte Hybrid-Hydrogele, mit HA und GelAGE, mit reinen HA-Hydrogelen zu vergleichen. Obwohl der Polymeranteil von HHAPA + LHASH Hydrogelen signifikant geringer war, als im Vergleich zu Hybrid-Hydrogelen (GelAGE + LHASH), wurden für gleiche En:SH Verhältnisse ähnliche mechanische und physikochemische Eigenschaften reiner HA-Hydrogele bestimmt. Aufgrund der geringen Viskosität niedermolekularer HA Lösungen (LHAPA + LHASH) konnten diese nicht für den Extrusions-basierten Druck verwendet werden. Das nicht temperaturabhängige HHAPA + LHASH System hingegen konnte mit nur einem Viertel des Polymeranteils der Hybrid Formulierungen gedruckt werden. Im Vergleich zu der Hybrid Bio-Tinte wurde angenommen, dass das hoch viskose Verhalten von HHAPA + LHASH Lösungen, der geringere Polymeranteil, der geringere Druck für das Drucken und eine demzufolge geringere Scherspannung, maßgeblich zu der hohen Zellviabilität in Extrusions-basiert-biogedruckten Konstrukten beisteuerten. Die niedrigmolekulare HA Formulierung (LHAPA + LHASH) konnte zwar nicht für den Extrusions-basierten Druck verwendet werden, allerdings besitzt dieses System Potential für andere additive Fertigungstechniken wie z.B. der Stereolithographie. Um dieses System weiterzuentwickeln wäre, analog zu dem GelAGE System, eine detailliertere Studie zu den Funktionen eingekapselter Zellen hilfreich. Außerdem sollte die Initiierung dieses Systems mit dem Vis-Initiator untersucht werden. N2 - Aim of this thesis was the development of functionalizable hydrogel coatings for melt electrowritten PCL scaffolds and of bioprintable hydrogels for biofabrication. Hydrogel coatings of melt electrowritten scaffolds enabled to control the surface hydrophilicity, thereby allowing cell-material interaction studies of biofunctionalized scaffolds in minimal protein adhesive environments. For this purpose, a hydrophilic star- shaped crosslinkable polymer was used and the coating conditions were optimized. Moreover, newly developed photosensitive scaffolds facilitated a time and pH independent biofunctionalization. Bioprintable hydrogels for biofabrication were based on the allyl-functionalization of gelatin (GelAGE) and modified hyaluronic acid-products, to enable hydrogel crosslinking by means of the thiol-ene click chemistry. Optimization of GelAGE hydrogel properties was achieved through an in-depth analysis of the synthesis parameters, varying Ene:SH ratios, different crosslinking molecules and photoinitiators. Homogeneity of thiol-ene crosslinked networks was compared to free radical polymerized hydrogels and the applicability of GelAGE as bioink for extrusion-based bioprinting was investigated. Purely hyaluronic acid-based bioinks were hypothesized to maintain mechanical- and rheological properties, cell viabilities and the processability, upon further decreasing the overall hydrogel polymer and thiol content. Hydrogel coatings: Highly structured PCL scaffolds were fabricated with MEW and subjected to coatings with six-armed star-shaped crosslinkable polymers (sP(EO-stat-PO)). Crosslinking results from the aqueous induced hydrolysis of reactive isocyanate groups (NCO) of sP(EO-stat-PO) and increased the surface hydrophilicity and provided a platform for biofunctionalizations in minimal protein adhesive environments. Not only the coating procedure was optimized with respect to sP(EO-stat-PO) concentrations and coating durations, instead scaffold pre-treatments were developed, which were fundamental to enhance the final hydrophilicity to completely avoid unspecific protein adsorption on sP(EO-stat-PO) coated scaffolds. The sP(EO-stat-PO) layer thickness of around 100 nm generally allows in vitro studies not only in dependence on the scaffold biofunctionalization but also on the scaffold architecture. The hydrogel coating extent was assessed via an indirect quantification of the NCO-hydrolysis products. Knowledge of NCO-hydrolysis kinetics enabled to achieve a balance of sufficiently coated scaffolds while maintaining the presence of NCO-groups that were exploited for subsequent biofunctionalizations. However, this time and pH dependent biofunctionalization was restricted to small biomolecules. In order to overcome this limitation and to couple high molecular weight biomolecules another reaction route was developed. This route was based on the photolysis of diazirine moieties and enabled a time and pH independent scaffold biofunctionalization with streptavidin and collagen type I. The fibril formation ability of collagen was used to obtain different collagen conformations on the scaffolds and a preliminary in vitro study demonstrated the applicability to investigate cell-material interactions. The herein developed scaffolds could be applied to gain deeper insights into the fundamentals of cellular sensing. Especially the complexity by which cells sense e.g. collagen remain to be further elucidated. Therefore, different hierarchies of collagen-like conformations could be coupled to the scaffolds, e.g. gelatin or collagen-derived peptide sequences, and the activation of DDR receptors in dependence on the complexity of the coupled substances could be determined. Due to the strong streptavidin-biotin bond, streptavidin functionalized scaffolds could be applied as a versatile platform to allow immobilization of any biotinylated molecules. Gelatin-based bioinks: First the GelAGE products were synthesized with respect to molecular weight distributions and amino acid composition integrity. A detailed study was conducted with varying molar ratios of reactants and synthesis durations and implied that gelatin degradation was most dominant for high alkaline synthesis conditions with long reaction times. Gelatin possesses multiple functionalizable groups and the predominant functionalization of amine groups was confirmed via different model substances and analyses. Polymer network homogeneity was proven for the GelAGE system compared to free radical polymerized hydrogels with GelMA. A detailed analysis of hydrogel compositions with varying functional group ratios and UV- or Vis-light photoinitiators was executed. The UV-initiator concentration is restricted due to cytotoxicity and potential cellular DNA damages upon UV-irradiation, whereas the more cytocompatible Vis- initiator system enabled mechanical stiffness tuning over a wide range by controlling the photoinitiator concentration at constant Ene:SH ratios and polymer weight percentages. Versatility of the GelAGE bioink for different AM techniques was proved by exploiting the thermo-gelling behavior of differently degraded GelAGE products for stereolithography and extrusion-based printing. Moreover, the viability of cell-laden GelAGE constructs was demonstrated for extrusion-based bioprinting. By applying different multifunctional thiol-macromolecular crosslinkers the mechanical and rheological properties improved concurrently to the processability. Importantly, lower thiol-crosslinker concentrations were required to yield superior mechanical strengths and physico-chemical properties of the hydrogels as compared to the small bis-thiol-crosslinker. Extrusion-based bioprinting with distinct encapsulated cells underlined the need for individual optimization of cell-laden hydrogel formulations. Not only the viability of encapsulated cells in extrusion-based bioprinted constructs should be assessed, instead other parameters such as cell morphology or production of collagen or glycosaminoglycans should be considered as these represent some of the crucial prerequisites for cartilage Tissue Engineering applications. Moreover, these studies should be expanded to the stereolithographic approach and ultimately the versatility and cytocompatibility of formulations with macromolecular crosslinkers would be of interest. Macromolecular crosslinkers allowed reducing polymer weight percentages and amounts of thiol groups and are thus expected to contribute to increased cytocompatibility, especially in combination with the more cytocompatible Vis-initiator system, which remains to be elucidated. Hyaluronic acid-based bioinks: Different molecular weight hyaluronic acid (HA) products were synthesized to bear ene- (HAPA) or thiol-functionalities (LHASH) to enable pure HA thiol-ene crosslinked hydrogels. Depending on the molecular weight of modified HA products, polymer weight percentages and Ene:SH ratios, a wide range of mechanical stiffness was covered. However, the manageability of high molecular weight HA (HHAPA) product solutions (HHAPA + LHASH) was restricted to 5.0 wt.-% as a consequence of the high viscosity. Based on the same HA thiol component (LHASH), hybrid hydrogels of HA with GelAGE were compared to pure HA hydrogels. Although the overall polymer weight percentage of HHAPA + LHASH hydrogels was significantly lowered compared to hybrid hydrogels (GelAGE + LHASH), similar mechanical and physico-chemical properties of pure HA hydrogels were determined with maintained Ene:SH ratios. Low viscous low molecular weight HA precursor solutions (LHAPA + LHASH) prevented the applicability for extrusion-based bioprinting, whereas the non-thermoresponsive HHAPA + LHASH system could be bioprinted with only one-fourth of the polymer content of hybrid formulations. The high viscous behavior of HHAPA + LHASH solutions, lower polymer weight percentages, decreased printing pressures and consequently declined shear stress during printing, were hypothesized to contribute to high cell viabilities in extrusion-based bioprinted constructs compared to the hybrid bioink. The low molecular weight HA precursor formulation (LHAPA + LHASH) was not applicable for extrusion-based printing, but this system has potential for other AM techniques such as stereolithography. Similar to the GelAGE system a more detailed study on the functions of encapsulated cells would be useful to further develop this system. Moreover, the initiation with the Vis-initiator should be conducted. KW - Biomaterial KW - Bioink KW - hydrogel KW - biofabrication KW - Hydrogel Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-174225 ER - TY - THES A1 - Wimmer, Katharina T1 - Analyse der Osteoklastendifferenzierung auf elektrochemisch abgeschiedenen strontiumdotierten Struvitschichten T1 - Differentiation of osteoclastic cells on electrochemically deposited strontium substituted struvite coatings N2 - Bei der Implantatversorgung von Patienten mit Osteoporose besteht weiterhin eine hohe Komplikationsrate vor allem durch aseptische Prothesenlockerungen. Eine vielversprechende Möglichkeit diese zu minimieren stellt eine Funktionalisierung der Implantate mit Strontium dar. Ziel der vorliegenden Arbeit war es dabei die Wirkung lokal verfügbaren Strontiums auf osteoklastäre und osteoblastäre Zellen zu untersuchen. Mittels elektrochemischer Abscheidung erfolgte die Beschichtung von Titanproben mit strontiumdotiertem Struvit, wobei sieben verschiedene Dotierkonzentrationen zwischen 6 µg und 487 µg Strontium pro Probe hergestellt wurden. Die Untersuchungen an osteoklastären RAW 264.7 Zellen erfolgten mittels Bestimmung von Zellzahl und -aktivität, verschiedener mikroskopischer Methoden sowie auf genetischer Ebene. Osteoblastäre MG63-Zellen wurden orientierend anhand von Zellzahl und Zellaktivität untersucht. Zellbiologisch konnte ein hemmender Einfluss von Strontium auf Differenzierung sowie Proliferation und Aktivität osteoklastärer Zellen gezeigt werden. Die Dotierkonzentration mit den günstigsten Eigenschaften war unter vorliegenden Versuchsbedingungen 487 µg Strontium pro Probe, da sich hierbei zudem eine erhaltene ostoblastäre Proliferation und Aktivität zeigte. N2 - Aseptic loosening of implants is still an issue especially for patients with osteoporosis. In order to minimize the risk of implant failure the functionalisation of implant surfaces with strontium is a promising technique. The aim of the present study was to investigate the effect of locally availible strontium on osteoclastic and osteoblastic cells. Electrochemically assisted deposition was used to provide strontium substituted struvite coatings on titanium surfaces. The strontium concentration ranged from 6 µg to 487 µg per sample. Growth of osteoclastic cells was investigated by the determination of cell number and cellular activity, as well as microscopical and transcriptional level studies. Osteoblasts were studied by determining cell number and cell activity. A general suppressing influence of strontium was observed on the differentiation and activity of osteoclasts. The most favourable properties were found for the highest strontium concentration under investigation, because additionally cell proliferation and activity of osteoblasts was not significantly affected. KW - Osteoblast KW - Strontium KW - Struvit KW - Galvanische Abscheidung KW - Osteoklastendifferenzierung KW - strontiumdotierte Struvitschichten Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-191417 ER - TY - THES A1 - Wiesbeck, Christina T1 - Fabrication and characterization of NCO-sP(EO-stat-PO)- crosslinked and functionalized electrospun gelatin scaffolds for tissue engineering applications T1 - Herstellung und Charakterisierung von elektrogesponnenen Nanofasern aus Gelatine und NCO-sP(EO-stat-PO) für Tissue Engineering Anwendungen N2 - In Tissue Engineering, scaffolds composed of natural polymers often show a distinct lack in stability. The natural polymer gelatin is highly fragile under physiological conditions, nevertheless displaying a broad variety of favorable properties. The aim of this study was to fabricate electrospun gelatin nanofibers, in situ functionalized and stabilized during the spinning process with highly reactive star polymer NCO-sP(EO-stat-PO) (“sPEG”). A spinning protocol for homogenous, non-beaded, 500 to 1000 nm thick nanofibers from different ratios of gelatin and sPEG was successfully established. Fibers were subsequently characterized and tested with SEM imaging, tensile tests, water incubation, FTIR, EDX, and cell culture. It was shown that adding sPEG during the spinning process leads to an increase in visible fiber crosslinking, mechanical stability, and stability in water. The nanofibers were further shown to be biocompatible in cell culture with RAW 264.7 macrophages. N2 - Tissue Engineering Scaffolds aus natürlichen Polymeren zeigen häufig mangelnde Stabilität, insbesondere unter physiologischen Bedingungen. Das natürliche Polymer Gelatine besitzt einige sehr vorteilhafte Eigenschaften für die Anwendung bei der Produktion künstlicher Körpergewebe. Beim Einsatz im menschlichen Organismus ist die Gelatine durch ihre Wasserlöslichkeit höchst fragil. Das Ziel dieser Arbeit war die Herstellung von Nanofaser-Scaffolds aus Gelatine mittels Elektrospinning und deren in situ Stabilisierung durch das Sternpolymer NCO-sP(EO-stat-PO) („sPEG“). Zunächst wurde ein Spinningprotokoll zur Fabrikation homogener, glatter, 500 bis 1000 nm dicker Nanofasern in verschiedenen Verhältnissen von Gelatine und sPEG erarbeitet. Mittels REM Bildgebung, Zugversuchen, Wasserinkubationsversuchen, FTIR, EDX und Zellkultur wurden die Fasern untersucht und charakterisiert. Es konnte gezeigt werden, dass die Zugabe von sPEG während des Spinningprozesses zu einer sichtbaren Quervernetzung der Fasern, sowie zu einem Anstieg der mechanischen Festigkeit und der Wasserstabilität führt. Des Weiteren wurde die Biokompatibilität der Nanofasern in der Zellkultur mit RAW 264.7 Makrophagen belegt. KW - Tissue Engineering KW - Electrospinning KW - Gelatine KW - Polyethylenglykole KW - NCO-sP(EO-stat-PO) KW - sPEG KW - starPEG Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-190988 ER - TY - THES A1 - Bengel, Melanie T1 - In vitro Testung neuer Anwendungsformen kalthärtender Knochenzemente aus resorbierbaren Orthophosphaten T1 - In vitro testing of new applications of cold-curing bone cements from absorbable orthophosphates N2 - Ziel der vorliegenden Arbeit war die Herstellung und Erprobung von innovativen Anwendungsformen kalthärtender Knochenersatzmaterialien aus Calcium-, und Magnesiumphosphaten, die nach dem Abbindevorgang vorzugsweise aus dem Mineral Struvit (MgNH4PO4·6H2O) bestehen. Diese neuartigen Knochenzemente versprechen im Vergleich zu den herkömmlichen Knochenersatzmaterialien eine deutlich schnellere knöcherne Regeneration und Abbaubarkeit. Damit wird das Ziel verfolgt schneller Implantate setzen zu können und dem Patienten somit eine lange Wartezeit und dementsprechenden Leidensdruck ersparen zu können. Ebenso müssen konventionelle Produkte erst im OP angerührt und hiernach in einem schmalen Zeitfenser verarbeitet werden. Die präfabrizierten Zement-Pasten sind dagegen direkt applikationsbereit und härten erst nach Kontakt mit dem feuchten Milieu aus. In vorangegangenen Projekten wurden sowohl präfabrizierte Pasten als auch Granulate auf Basis Struvit-bildender Calcium-Magnesiumphosphate erfolgreich entwickelt. Vorteil dieser Granulate ist ihre sphärische Form. Im Hinblick auf die klinische Anwendbarkeit sollten in der vorliegenden Studie beide Anwendungsformen vorgreifend auf eine tierexperimentelle Studie hinsichtlich ihrer Materialeigenschaften in vitro getestet werden. N2 - The aim of the present work was the production and testing of innovative application forms of cold-curing bone replacement materials from calcium and magnesium phosphates, which after the binding process preferably consist of the mineral struvit (MgNH4PO4-6H2O). Compared to conventional bone replacement materials, these novel bone cements promise significantly faster bony regeneration and degradability. The aim is to be able to put implants faster and thus to save the patient a long waiting time and corresponding suffering pressure. Similarly, conventional products must first be stirred in the operating room and then processed in a narrow time-fenser. The prefabricated cement pastes, on the other hand, are directly ready for application and harden only after contact with the damp environment. In previous projects, both prefabricated pastes and granules based on struvit-forming calcium-magnesium phosphates were successfully developed. The advantage of these granules is their spherical shape. With regard to clinical applicability, both forms of application should be tested in vitro in the present study in anticipation of an animal-experimental study with regard to their material properties. KW - Knochenzemente KW - Zementpaste KW - Granulate KW - Calcium-Magnesium-Phosphat-Zemente KW - Bone Cement KW - Granules KW - Cement Paste KW - Calcium-Magnesium-Phosphates-Cements Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-186435 ER - TY - THES A1 - Maier, Alexander T1 - Analyse der Expression osteogener Markerproteine in humanen mesenchymalen Stromazellen nach Kultur auf elektrogesponnenen Scaffolds T1 - Analysis of the expression of osteogenic marker proteins in human mesenchymal stromal cells after culture on electrospun scaffolds N2 - Es wurde die Expression der osteogenen Markerproteine Alkalische Phosphatase, Bone Sialoprotein, Kollagen Typ I und Osteopontin von humanen mesenchymalen Stromazellen nach Kultur auf elektrogesponnenen Scaffolds analysiert. Die Scaffolds wurden mittels der Melt electrospinning writing Methode erstellt und unterschieden sich in ihrer Maschenweite. Anhand weiterer Kontrollversuche auf Monolayern wurde ein möglicher Einfluss der Geometrie auf die Proteinexpression untersucht. N2 - The Expression of the marker proteins alkaline phosphatase, bone sialoprotein, collagen type I and osteopontin of human mesenchymal stromal cells after culture on electrospun scaffolds was analyzed. The scaffolds were made by the melt electrospinning writing method and differed in their mesh size. Further control experiments on monolayers were used to investigate the possible influence of the scaffolds´ geometry on the expression of the proteins. KW - Scaffold KW - mesenchymale Stromazellen Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-184687 ER - TY - THES A1 - Rödel, Michaela T1 - Development of Dual Setting Cement Systems as Composite Biomaterials with Ductile Properties T1 - Entwicklung dual härtender Zemente als Komposit-Biomaterialien mit duktilen Eigenschaften N2 - Synthetic bone replacement materials have their application in non-load bearing defects with the function of (re-)construction or substitution of bone. This tissue itself represents a biological composite material based on mineralized collagen fibrils and combines the mechanical strength of the mineral with the ductility of the organic matrix. By mimicking these outstanding properties with polymer-cement-composites, an imitation of bone is feasible. A promising approach for such replacement materials are dual setting systems, which are generated by dissolution-precipitation reaction with cement setting in parallel to polymerization and gelation of the organic phase forming a coherent hydrogel network. Hereby, the high brittleness of the pure inorganic network was shifted to a more ductile and elastic behavior. The aim of this thesis was focused on the development of different dual setting systems to modify pure calcium phosphate cements’ (CPCs’) mechanical performance by incorporation of a hydrogel matrix. A dual setting system based on hydroxyapatite (HA) and cross-linked 2-hydroxyethyl methacrylate (HEMA) via radical polymerization was advanced by homogenous incorporation of a degradable cross-linker composed of poly(ethylene glycol) (PEG) as well as poly(lactic acid) (PLA) with reactive terminal methacrylate functionalities (PEG-PLLA-DMA). By integration of this high molecular weight structure in the HEMA-hydrogel network, a significant increase in energy absorption (toughness) under 4-point bending testing was observed. An addition of only 10 wt% hydrogel precursor (referred to the liquid phase) resulted in a duplication of stress over a period of 8 days. Additionally, the calculated elasticity was positively affected and up to six times higher compared to pure HA. With a constantly applied force during compressive strength testing, a deformation and thus strain levels of about 10 % were reached immediately after preparation. For higher degradability, the system was modified in a second approach regarding organic as well as inorganic phase. The latter component was changed by brushite forming cement that is resorbable in vivo due to solubility processes. This CPC was combined with a hydrogel based on PEG-PLLA-DMA and other dimethacrylated PEGs with different molecular weights and concentrations. Hereby, new reaction conditions were created including a shift to acidic conditions. On this ground, the challenge was to find a new radical initiator system. Suitable candidates were ascorbic acid and hydrogen peroxide. that started the polymerization and successful gelation in this environment. These highly flexible dual set composites showed a very high ductility with an overall low strength compared to HA-based models. After removal of the applied force during compressive strength testing, a complete shape recovery was observed for the samples containing the highest polymeric amount (50 wt%) of PEG-PLLA-DMA. Regarding phase distribution in the constructs, a homogenously incorporated hydrogel network was demonstrated in a decalcifying study with ethylenediaminetetraacetic acid. Intact, coherent hydrogels remained after dissolution of the inorganic phase via calcium ion complexation. In a third approach, the synthetic hydrogel matrix of the previously described system was replaced by the natural biopolymer gelatin. Simultaneously to brushite formation, physical as well as chemical cross-linking by the compound genipin was performed in the dual setting materials. Thanks to the incorporation of gelatin, elasticity increased significantly, in which concentrations up to 10.0 w/v% resulted in a certain cohesion of samples after compressive strength testing. They did not dissociate in little pieces but remained intact cuboid specimens though having cracks or fissures. Furthermore, the drug release of two active pharmaceutical ingredients (vancomycin and rifampicin) was investigated over a time frame of 5 weeks. The release exponent was determined according to Korsmeyer-Peppas with n = 0.5 which corresponds to the drug liberation model of Higuchi. A sustained release was observed for the antibiotic vancomycin encapsulated in composites with a gelatin concentration of 10.0 w/v% and a powder-to-liquid ratio of 2.5 g/mL. With respect to these developments of different dual setting systems, three novel approaches were successfully established by polymerization of monomers and cross-linking of precursors forming an incorporated, homogenous hydrogel matrix in a calcium phosphate network. All studies showed an essential transfer of mechanical performance in direction of flexibility and bendability. N2 - Synthetische Knochenersatzmaterialien finden ihre Anwendung im Bereich nicht lasttragender Defekte zum Wiederaufbau und Ersatz von defekter oder verlorener Knochensubstanz. Diese stellt aufgrund ihres Aufbaus aus mineralisierten Kollagen-Fibrillen selbst ein biologisches Komposit-Material dar, welches die mechanische Festigkeit des Minerals mit der Duktilität der organischen Matrix kombiniert. Eine Nachahmung dieser herausragenden Eigenschaften des Knochens wird im Sinne eines Ersatzmaterials durch geeignete Polymer-Zement-Komposite ermöglicht. Ein vielversprechender Ansatz für solche Komposite sind hierbei dual härtende Systeme, bei denen die Lösungs-Fällungs-Reaktion der Zementbildung parallel zur Polymerisation oder Gelierung der organischen Phase zu einem kohärenten Hydrogelnetzwerk abläuft. Die hohe Sprödigkeit und Bruchanfälligkeit rein anorganischer Netzwerke sollte dabei durch die Integration elastischer Polymerkomponenten hin zu mehr Flexibilität und Elastizität modifiziert werden. In der vorliegenden Arbeit wurden verschiedene dual härtende Hybrid-Materialien entwickelt, um etablierte Calciumphosphatzemente durch Einbringen von zusätzlicher Hydrogel-Matrizes bezüglich ihrer mechanischen Eigenschaften zu modifizieren. In ein dual härtendes System aus Hydroxylapatit (HA) und radikalisch vernetztem 2-Hydroxyethlymethacrylat (HEMA), wurde ein abbaubarer Cross-linker aus Polyethylenglykol (PEG) und Polymilchsäure (PLA)-Einheiten homogen inkorporiert, der mittels einer Reaktion der terminalen Methacrylatfunktionen (PEG-PLLA-DMA) zur Ausbildung der Vernetzungen führte und mittels PLLA hydrolytisch labile Esterbindungen ins System integrierte. Durch Einbringen dieser hochmolekularen Polymere in das engmaschige HEMA-Hydrogelnetzwerk kam es zu einer signifikanten Erhöhung der Energieaufnahme des Konstruktes unter 4-Punkt-Biegebelastung im Vergleich zum bereits etablierten System. Durch Zusatz von 10 Gew% hochmolekularem Hydrogel Präkursor (bezogen auf die flüssige Phase) konnte über einen Zeitraum von acht Tagen ein zweifach höherer Bruchwiderstand erhalten werden, verbunden mit einer bis zu sechsfach höheren Elastizität gegenüber reinem HA Zement. Zur Steigerung der Bioabbaubarkeit wurde in einem zweiten Ansatz durch Austausch der anorganischen Komponente mit einem in vivo leichter resorbierbaren Bruschit Zement das dual härtende System modifiziert. Dabei wurden dimethacrylierte PEGs verschiedener Molekulargewichte in unterschiedlichen Konzentrationen mit dem Zementpulver kombiniert. Die Reaktionsbedingungen im sauren Milieu erforderten den Austausch des radikalischen Initiator-Systems, wobei sich eine Kombination aus Ascorbinsäure und Wasserstoffperoxid als geeignet erwies. Die so erhaltenen dual härtenden Komposite zeigten eine sehr hohe Duktilität und Flexibilität bei insgesamt niedriger Festigkeit im Vergleich zu HA-basierenden Systemen. So fand im Druckversuch eine vollständige Relaxation zu den Ausgangsabmessungen des Prüfkörpers bei einem hohen Polymeranteil an PEG-PLLA-DMA (50 Gew%) statt. Die homogene Verteilung der inkorporierten Polymerphase wurde mittels Decalcifizierung durch Ethylendiamintetraessigsäure bewiesen. Hierbei wurden durchgängige Hydrogele nach Herauslösen der anorganischen Phase durch Komplexierung von Calcium-Ionen erhalten. Abschließend wurde die auf synthetischen Polymeren basierende Hydrogel-Matrix durch das natürliche Biopolymer Gelatine ersetzt. Neben der Bruschit-bildenden Zement-Reaktion wurde das Polymernetzwerk sowohl durch eine physikalische Gelierung als auch eine chemische Vernetzung mit Genipin stabilisiert. Durch die zusätzliche organische Phase wurden die Eigenschaften des Zementes hinsichtlich Elastizität erhöht, wobei bei einer Gelatine-Konzentration von 10,0 Gew% eine erneute Kohäsion der Prüfkörper nach mechanischer Druckbelastung beobachtet werden konnte. Diese zerfielen nicht in einzelne Teile, sondern wurden trotz Auftreten von Rissen als weitestgehend intakte Quader zusammengehalten. Weiterhin wurde die Wirkstoff-Freisetzung zweier antibiotisch aktiver Substanzen (Vancomycin und Rifampicin) über einen Zeitraum von fünf Wochen untersucht. Mittels Bestimmung des Freisetzungsexponenten nach Korsmeyer-Peppas konnte eine verzögerte Wirkstoffliberation für das Antibiotikum Vancomycin gemäß Wurzel-t-Kinetik (Higuchi-Modell) mit n = 0,5 für ein Pulverflüssigkeitsverhältnis von 2,5 g/mL bei einer Gelatinekonzentration von 10,0 Gew% erhalten werden. Im Hinblick auf die Entwicklung verschiedener Formulierungen als dual härtende Systeme wurden in der vorliegenden Arbeit drei Varianten etabliert, die durch Polymerisation von Monomeren beziehungsweise Hydrogel-Präkursoren zu einer inkorporierten, homogenen Hydrogel-Matrix im Calciumphosphatnetzwerk führten. Bei allen Ansätzen wurde ein wesentlicher Transfer der mechanischen Eigenschaften in Richtung Flexibilität und Biegsamkeit erzielt. KW - Calciumphosphate KW - Knochenzement KW - Hydrogel KW - Dual setting system KW - Ceramic polymer composite KW - Calciumphosphatzemente Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-182776 ER - TY - THES A1 - Wistlich, Laura T1 - NCO-sP(EO-stat-PO) as functional additive for biomaterials’ development T1 - NCO-sP(EO-stat-PO) als funktionale Additive für die Entwicklung von Biomaterialien N2 - The aim of this thesis was the application of the functional prepolymer NCO-sP(EO-stat-PO) for the development of new biomaterials. First, the influence of the star-shaped polymers on the mechanical properties of biocements and bone adhesives was investigated. 3-armed star-shaped macromers were used as an additive for a mineral bone cement, and the influence on the mechanical properties was studied. Additionally, a previously developed bone adhesive was examined regarding cytocompatibility. The second topic was the examination of novel functionalization steps which were performed on the surface of electrospun fibers modified with NCO-sP(EO-stat-PO). This established method of functionalizing electrospun meshes was advanced regarding the modification with proteins which was then demonstrated in a biological application. Two different kinds of antibodies were immobilized on the fiber surface in a consecutive manner and the influence of these proteins on the cell behavior was investigated. The final topic involved the quantification of surface-bound peptide sequences. By functionalization of the peptides with the UV-reactive molecule 2-mercaptopyridine it was possible to quantify this compound via UV measurements by cleavage of disulfide bridges and indirectly draw conclusions about the number of immobilized peptides. In the field of mineral biocements and bone adhesives, NCO-sP(EO-stat-PO) was able to influence the setting behavior and mechanical performance of mineral bone cements based on calcium phosphate chemistry. The addition of NCO-sP(EO-stat-PO) resulted in a pseudo-ductile fracture behavior due to the formation of a hydrogel network in the cement, which was then mineralized by nanosized hydroxyapatite crystals following cement setting. Accordingly, a commercially available aluminum silicate cement from civil engineering could be modified. In addition, it could be shown that the use of NCO-sP(EO-stat-PO) is beneficial for adjusting specific material properties of bone adhesives. Here, the crosslinking behavior of the prepolymer in an aqueous medium was exploited to form an interpenetrating network (IPN) together with a photochemically curing poly(ethylene glycol) dimethacrylate (PEGDMA) matrix. This could be used for the development of a bone adhesive with an improved adhesion to bone in a wet environment. The developed bone adhesive was further investigated in terms of possible influences of the initiator systems. In addition, the material system was tested for cytocompatibility by using different cell lines. Moreover, the preparation of electrospun fiber meshes via solution electrospinning consisting of poly(lactide-co-glycolide) (PLGA) as a backbone polymer and NCO-sP(EO-stat-PO) as functional additive is an established method for the application of the meshes as a replacement of the native extracellular matrix (ECM). In general, these fibers reveal diameters in the nanometer range, are protein and cell repellent due to the hydrophilic properties of the prepolymer and show a specific biofunctionalization by immobilization of peptide sequences. Here, the isocyanate groups presented on the fiber surface after electrospinning were used to carry out various functionalization steps, while retaining the properties of protein and cell repellency. The modification of the electrospun fibers involved the immobilization of analogs or antagonists of tumor necrosis factor (TNF) and the indirect detection of these by interaction with a light-producing enzyme. Here, a multimodal modification of the fiber surface with RGD to mediate cell adhesion and two different antibodies could be achieved. After culturing the cell line HT1080, the pro- or anti-inflammatory response of cells could be detected by IL-8 specific ELISA measurements. Furthermore, the quantification of molecules on the surface of electrospun fibers was investigated. It was tested whether the detection by means of super-resolution microscopy would be possible. Therefore, experiments were performed with short amino acid sequences such as RGD for quantification by fluorescence microscopy. Based on earlier results, in which a UV-spectrometrically active molecule was used to detect the quantification of RGD, it was shown that short peptides can also be quantified in a small scale on flat functional substrates (2D) such as NCO-sP(EO-stat-PO) hydrogel coatings, and modified electrospun fibers produced from PLGA and NCO-sP(EO-stat-PO) (3D). In addition, a collagen sequence was used to prove that a successful quantification can be carried out as well for longer peptide chains. These studies have revealed that NCO-sP(EO-stat-PO) can serve as a functional additive for many applications and should be considered for further studies on the development of novel biomaterials. The rapid crosslinking reaction, the resulting hydrogel formation and the biocompatibility are to be mentioned as positive properties, which makes the prepolymer interesting for future applications. N2 - Ziel der Arbeit war die Anwendung der funktionalen Präpolymere NCO-sP(EO-stat-PO) für die Entwicklung von neuen Biomaterialien. Als erstes wurde untersucht, welchen Einfluss die sternförmigen Polymere auf die mechanischen Eigenschaften von Biozementen und Knochenadhäsiven haben. Beispielsweise wurden 3-armige Macromere als Additive für einen mineralischen Knochenzement verwendet und dessen mechanische Eigenschaften untersucht. Außerdem wurde ein kürzlich entwickelter NCO-sP(EO-stat-PO) haltiger Knochenklebers auf Zytokompatibilität getestet. Ein zweites Kapitel beinhaltete die Modifikation von elektrogesponnenen Polymerfasern mit NCO-sP(EO-stat-PO) basierend auf einer etablierten Methode. Es wurde untersucht, welche weiteren Funktionalisierungen auf solchen Oberflächen vorgenommen werden können. Diese Modifizierungsschritte wurden in einer biologischen Anwendung demonstriert, indem verschiedene Antikörper aufeinanderfolgend auf der Faseroberfläche gebunden wurden. Der Einfluss dieser Proteine auf das Verhalten von Zellen auf diesen Oberflächen wurde untersucht. Als letztes wurde die Quantifizierung von oberflächengebundenen Peptidsequenzen demonstriert. Mittels Funktionalisierung der Peptide mit dem UV-reaktiven Molekül 2-Mercaptopyridin konnte durch Spaltung von Disulfidbrücken diese Verbindung UV-metrisch quantifiziert und indirekt Rückschlüsse auf die Anzahl der immobilisierten Peptide gezogen werden. Durch den Zusatz von NCO-sP(EO-stat-PO) konnten das Abbindeverhalten und die mechanischen Eigenschaften von mineralischen Calciumphosphat-Knochenzementen moduliert werden. Der Zusatz von 3-armigem, sternförmigem NCO-sP(EO-stat-PO) führte dabei zu einem pseudoduktilen Bruchverhalten durch Bildung eines Hydrogelnetzwerks im Zement, das anschließend durch die Zementreaktion mit nanoskaligem Hydroxylapatit mineralisiert wurde. Im Bereich mineralischer Knochenzemente und Adhäsive konnte gezeigt werden, dass NCO-sP(EO-stat-PO) zur Einstellung der Eigenschaften verwendet werden kann. Hierbei wurde dessen Quervernetzungsverhalten im wässrigen Medium ausgenutzt, um mit einer photochemisch härtenden Polyethylenglykoldimethakrylat (PEGDMA) Matrix interpenetrierende Netzwerke (IPNs) zu bilden. Diese konnten für die Entwicklung eines Knochenklebers mit verbesserter Haftung auf Knochen im feuchten Milieu genutzt werden. Das kürzlich entwickelte Knochenadhäsiv wurde im Hinblick auf den Einfluss des Initiatorsystems untersucht. Außerdem wurde die Zytokompatibilität des Materials anhand verschiedener Zelltypen getestet. Die Herstellung von elektrogesponnenen Faservliesen mittels Solution Electrospinning aus Polylactid-co-Glycolid (PLGA) als Gerüst-bildendem Polymer und NCO-sP(EO-stat-PO) als funktionalem Additiv ist eine etablierte Methode, um diese Vliese zur Nachbildung nativer Extrazellulär-Matrix anzuwenden. Die Fasern weisen einen Durchmesser im Nanometer-Bereich auf, sind proteinabweisend durch die hydrophilen Eigenschaften des Präpolymers und können durch Immobilisierung von Peptidsequenzen spezifisch biofunktionalisiert werden. Hierbei wurden die Isocyanate auf der Faseroberfläche genutzt, um verschiedenste Funktionalisierungsschritte unter Beibehaltung der protein- und zellabweisenden Eigenschaften auszuführen. Die Modifizierung der elektrogesponnenen Fasern beinhaltete die Immobilisierung von Analoga oder Antagonisten des Tumornekrosefaktors (TNF) sowie den indirekten Nachweis über eine Lichtreaktion. Hierbei konnte eine multimodale Modifizierung der Faseroberfläche mit RGD-Sequenzen zur Vermittlung der Zelladhäsion und zwei verschiedenen Antikörpern erreicht werden. Nach Kultivierung der Zelllinie HT1080 konnte die pro- oder antiinflammatorische Antwort der Zellen mittels IL-8 spezifischem ELISA nachgewiesen werden. Eine weitere Fragestellung war der Quantifizierung von Molekülen auf der Oberfläche von elektrogesponnen Fasern gewidmet. Es wurde getestet, ob ein Nachweis mittels hochauflösender Mikroskopie möglich ist. Hierzu wurden RGD-Sequenzen zur fluoreszenzmikroskopischen Quantifizierung verwendet. Basierend auf früheren Ergebnissen, bei denen für die Quantifizierung von RGD ein UV-aktives Molekül genutzt wurde, konnte gezeigt werden, dass sich kurze Peptide auch im kleinen Maßstab auf flachen Substraten (2D) wie Hydrogel-Beschichtungen aus NCO-sP(EO-stat-PO) als auch auf elektrogesponnenen Fasern aus PLGA und NCO-sP(EO-stat-PO) (3D) quantifizieren lassen. Außerdem wurde eine Kollagen-Sequenz als längere Peptidkette herangezogen, um auch hier eine erfolgreiche Quantifizierung zu beweisen. Es konnte gezeigt werden, dass NCO-sP(EO-stat-PO) als funktionales Additiv für viele Anwendungen dienen kann und für weitere Untersuchungen zur Entwicklung von Biomaterialien berücksichtigt werden sollte. Die schnelle Quervernetzungsreaktion, die resultierende Hydrogelbildung und die Biokompatibilität sind als positive Eigenschaften zu nennen, die das Präpolymer für zukünftige Anwendungen interessant macht. KW - Sternpolymere KW - Funktionalisierung KW - Isocyanate KW - surface functionalization KW - biomaterials KW - chemical crosslinking KW - bioceramics KW - electrospun fibers KW - Oberflächenfunktionalisierung KW - funktionale Präpolymere KW - Modifikation von Biokeramiken KW - Funktionalisierung von elektrogesponnenen Fasern Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-178365 ER - TY - THES A1 - Jüngst, Tomasz T1 - Establishing and Improving Methods for Biofabrication T1 - Etablierung und Verbesserung von Methoden für die Biofabrikation N2 - Die Biofabrikation ist ein junges und sehr dynamisches Forschungsgebiet mit viel Potential. Dieses Potential spiegelt sich unter anderem in den ambitionierten Zielen wieder, die man sich hier gesetzt hat. Wissenschaftler in diesem Gebiet wollen eines Tages beispielsweise funktionale menschliche Gewebe nachbilden, die aus patienteneigenen Zellen bestehen. Diese Gewebe sollen entweder für die Testung neuer Arzneimittel und Therapien oder sogar als Implantate einsetzt werden. Der Schlüssel zum Erfolg soll hier die Verwendung automatisierter Prozesse in Verbindung mit innovativen Materialien sein, die es ermöglichen, die Hierarchie und Funktion des zu ersetzenden natürlichen Gewebes nachbilden. Obwohl in den letzten Jahren große Fortschritte gemacht worden sind, gibt es immer noch Hürden, die überwunden werden müssen. Ziel dieser Arbeit war es deshalb, die derzeit eingeschränkte Auswahl kompatibler Materialien für die Biofabrikation zu erweitern und bereits etablierte Verfahren wie den extrusionsbasierten Biodruck noch besser verstehen zu lernen. Auch neue Verfahren, wie etwa das Melt Electrospinning Writing (MEW) sollten etabliert werden. In Kapitel 3 dieser Arbeit wurde das MEW dazu verwendet, tubuläre Strukturen zu fertigen, die sich aus Polymerfasern mit einem durchschnittlichen Durchmesser von nur etwa 12 μm zusammensetzen. Die mit Hilfe von Druckluft in Verbindung mit einer hohen elektrischen Spannung aus einer Nadelspitze austretende Polymerschmelze wurde hierbei auf zylinderförmigen Kollektoren mit Durchmessern zwischen 0.5 und 4.8mm gesammelt. Auf diese Weise wurden röhrenförmige Faserkonstrukte generiert. Das Hauptaugenmerk lag auf dem Einfluss des Durchmessers, der Rotations- und Translationsbewegung des Kollektors auf die Morphologie der Faserkonstrukte. Hierzu wurden die Fasern erst auf unbewegten Kollektoren mit unterschiedlichen Durchmessern gesammelt und die entstehenden Muster analysiert. Es zeigte sich, dass das Fasermuster mit zunehmendem Durchmesser des Kollektors mehr den symmetrischen Konstrukten mit runder Grundfläche glich, die auch von flachen Kollektoren bekannt sind. Je kleiner der Kollektordurchmesser wurde, desto ovaler wurde die Grundfläche der Muster, was den Einfluss der Krümmung deutlich machte. In weiteren Experimenten wurden die zylindrischen Kollektoren mit Geschwindigkeiten von 4,2 bis 42 Umdrehungen pro Minute um ihre Längsachse gedreht. Die von flachen Kollektoren bekannten Übergänge der Fasermorphologie konnten auch für runde Kollektoren bestätigt werden. So änderte sich die Morphologie mit zunehmender Geschwindigkeit der Oberfläche von einer achterförmigen Gestalt über eine sinusförmige Ausrichtung der Fasern hin zu einer geraden Linie. Der Einfluss des Kollektordurchmessers wurde auch hier deutlich, da sich etwa die Amplitude der bei Rotationsgeschwindigkeiten im Bereich sinusförmiger Ausrichtung abgelegten Fasern mit abnehmendem Radius erhöhte. Im nächsten Schritt wurde neben der Rotation der Kollektoren auch eine Translation induziert. Durch geeignete Kombination von Rotation und Translation konnten Konstrukte mit definiertem Wickelwinkel hergestellt werden. Es zeigte sich, dass die Wiedergabe des vorher kalkulierten Winkels unter Verwendung von Oberflächengeschwindigkeiten, die nahe am Übergang zur geraden Faserausrichtung waren, am besten war. Im Rahmen dieser Arbeit konnten Winkel zwischen 5 und 60° mit hoher Präzision wiedergegeben werden. Im Falle von sich wiederholenden Mustern konnte auch in Bezug auf die Stapelbarkeit der Fasern aufeinander eine hohe Präzision erreicht werden. Kapitel 4 dieser Arbeit befasste sich mit dem extrusionsbasierten 3D-Druck. Das etabliere Verfahren wurde auf eine bisher wenig untersuchte Materialzusammensetzung von Nanopartikeln-beladenen Hydrogeltinten ausgeweitet. Die Tinte bestand aus einer Kombination von funktionalisierten Polyglyzidolen und einer unmodifizierten langkettingen Hyaluronsäure. Dieser wurden mesoporöse Silika-Nanopartikel mit unterschiedlicher Ladung zugesetzt und deren Freisetzung aus gedruckten Konstrukten mit einstellbarer Geometrien untersucht. Da die Hyaluronsäure selbst negativ geladen ist, wurde erwartet und auch gezeigt, dass aminofunktionalisierte Partikel mit positiver Ladung langsamer freigesetzt werden als carboxylfunktionalisierte Partikel mit negativer Ladung. Interessanterweise änderten die Partikel nicht die rheologischen Eigenschaften der Tinte und es konnten Hydrogele, die mit positiv geladenen Partikeln beladen waren, bei den gleichen Druckparametern verdruckt werden, wie Hydrogele, die mit negativ geladenen Partikeln beladen waren. Die guten Druckeigenschaften der Tinten ermöglichten die präzise Fertigung von Konstrukten mit einer Größe von 12x12x3mm^3, also von Konstrukten mit bis zu 16 aufeinanderfolgenden Lagen. Die Strangdurchmesser betrugen hierbei 627±31μm und die Verteilung der Partikel innerhalb der Stränge war sehr homogen. Zudem konnten auch Strukturen gedruckt werden, bei denen beide Tintenarten, mit positiven und mit negativen Partikeln beladene Hydrogele, in einem Konstrukt kombiniert wurden. Hierbei zeigte sich, dass die Freisetzung der Partikel, die über 6 Wochen hinweg untersucht wurde, auch stark von der Geometrie der zwei-Komponenten-Konstrukte abhing. Insbesondere die Auswirkung des direkten Kontakts zwischen den Komponenten innerhalb eines Konstruktes war hier sehr deutlich. Wurden die Stränge über Kreuz aufeinander abgelegt und hatten direkten Kontakt an den Kreuzungspunkten, konnte beobachtet werden, dass die positiv geladenen Partikel aus ihrem System in das mit den negativ geladenen Partikeln wanderten. Wurden die Stränge ohne direkten Kontakt parallel nebeneinander abgelegt, wurden die positiv geladenen Partikel in umgebendes Medium freigesetzt, konnten aber selbst nach 6 Wochen nicht in den Strängen mit den negativ geladenen Partikeln nachgewiesen werden. Dies verdeutlicht, dass Geometrie und Ladung der Partikel einen Einfluss auf die Freisetzung der Partikel hatten und sich die Freisetzung der Partikel durch eine geschickte Kombination beider Parameter steuern lässt. In Kapitel 5 dieser Arbeit wurde eine neue Materialklasse als Biotinte für den extrusionsbasierten Biodruck untersucht. Bei dem Material handelte es sich um Hydrogele auf Basis rekombinanter Spinnenseidenproteine. Diese konnten ab einer Proteinkonzentration von 3 %Gew./Vol. ohne die Verwendung von Verdickungsmittel oder anderen Additiven und auch ohne eine nachträgliche Vernetzung verdruckt werden. Sowohl Hydrogele auf Basis des rekombinanten Proteins eADF4(C16) als auch eine mit einer RGD-Sequenz versehene Modifikation (eADF4(C16)-RGD) konnten mit einer hohen Formtreue verdruckt werden. Die RGD-Sequenz zeigte einen positiven Effekt auf das Anhaften von humanen Fibroblasten, die auf gedruckte Konstrukte ausgesät wurden. Zudem konnten mit Hilfe der Hydrogele auch zellbeladene Konstrukte gefertigt werden. Hierzu wurden die Hydrogele mit einer Zellsuspension so vermengt, dass eine finale Konzentration von 1,2 Millionen Zellen/ml erreicht wurde. Die beladenen Gele wurden verdruckt und es konnte eine Überlebensrate von 70,1±7,6% nachgewiesen werden. Das in diesem Kapitel etablierte Materialsystem ermöglichte zum ersten Mal das Verdrucken lebender Zellen in einer neuen Klasse von Tinten, die weder die Beimengung von Verdickungsmittel noch einen zusätzlichen Nachhärtungsschritt für die Herstellung zellbeladener stabiler Konstrukte benötigt. N2 - Biofabrication is an advancing new research field that might, one day, lead to complex products like tissue replacements or tissue analogues for drug testing. Although great progress was made during the last years, there are still major hurdles like new types of materials and advanced processing techniques. The main focus of this thesis was to help overcoming this hurdles by challenging and improving existing fabrication processes like extrusion-based bioprinting but also by developing new techniques. Furthermore, this thesis assisted in designing and processing materials from novel building blocks like recombinant spider silk proteins or inks loaded with charged nanoparticles. A novel 3D printing technique called Melt Electrospinning Writing (MEW) was used in Chapter 3 to create tubular constructs from thin polymer fibers (roughly 12 μm in diameter) by collecting the fibers onto rotating and translating cylinders. The main focus was put on the influence of the collector diameter and its rotation and translation on the morphology of the constructs generated by this approach. In a first step, the collector was not moving and the pattern generated by these settings was analyzed. It could be shown that the diameter of the stationary collectors had a big impact on the morphology of the constructs. The bigger the diameter of the mandrel (smallest collector diameters 0.5 mm, biggest 4.8 mm) got, the more the shape of the generated footprint converged into a circular one known from flat collectors. In a second set of experiments the mandrels were only rotated. Increasing the rotational velocity from 4.2 to 42.0 rpm transformed the morphology of the constructs from a figure-of-eight pattern to a sinusoidal and ultimately to a straight fiber morphology. It was possible to prove that the transformation of the pattern was comparable to what was known from increasing the speed using flat collectors and that at a critical speed, the so called critical translation speed, straight fibers would appear that were precisely stacking on top of each other. By combining rotation and translation of the mandrel, it was possible to print tubular constructs with defined winding angles. Using collections speeds close to the critical translation speed enabled higher control of fiber positioning and it was possible to generate precisely stacked constructs with winding angles between 5 and 60°. In Chapter 4 a different approach was followed. It was based on extrusion-based bioprinting in combination with a hydrogel ink system. The ink was loaded with nanoparticles and the nanoparticle release was analyzed. In other words, two systems, a printable polyglycidol/hyaluronic acid ink and mesoporous silica nanoparticles (MSN), were combined to analyze charge driven release mechanism that could be fine-tuned using bioprinting. Thorough rheological evaluations proved that the charged nanoparticles, both negatively charged MSN-COOH and positively charged MSN-NH2, did not alter the shear thinning properties of the ink that revealed a negative base charge due to hyaluronic acid as one of its main components. Furthermore, it could be shown that the particles did also not have a negative effect on the recovery properties of the material after exposure to high shear. During printing, the observations made via rheological testing were supported by the fact that all materials could be printed at the same settings of the bioprinter. Using theses inks, it was possible to make constructs as big as 12x12x3 mm3 composed of 16 layers. The fiber diameters produced were about 627±31 μm and two-component constructs could be realized utilizing the two hydrogel print heads of the printer to fabricate one hybrid construct. The particle distribution within those constructs was homogeneous, both from a microscopic and a macroscopic point of view. Particle release from printed constructs was tracked over 6 weeks and revealed that the print geometry had an influence on the particle release. Printed in a geometry with direct contact between the strands containing different MSN, the positively charged particles quickly migrated into the strand previously containing only negatively charged MSN-COOH. The MSN-COOH seemed to be rather released into the surrounding liquid and also after 6 weeks no MSN-COOH signal could be detected in the strand previously only containing MSN-NH2. In case of a geometry without direct contact between the strands, the migration of the positively charged nanoparticles into the MSN-COOH containing strand was strongly delayed. This proved that the architecture of the printed construct can be used to fine-tune the particle release from nanoparticle containing printable hydrogel ink systems. Chapter 5 discusses an approach using hydrogel inks based on recombinant spider silk proteins processed via extrusion-based bioprinting. The ink could be applied for printing at protein concentrations of 3 % w/v without the addition of thickeners or any post process crosslinking. Both, the recombinant protein eADF4(C16) and a modification introducing a RGD-sequence to the protein (eADF4(C16)-RGD), could be printed revealing a very good print fidelity. The RGD modification had positive effect on the adhesion of cells seeded onto printed constructs. Furthermore, human fibroblasts encapsulated in the ink at concentrations of 1.2 million cells per mL did not alter the print fidelity and did not interfere with the crosslinking mechanism of the ink. This enabled printing cell laden constructs with a cell survival rate of 70.1±7.6 %. Although the cell survival rate needs to be improved in further trials, the approach shown is one of the first leading towards the shift of the window of biofabrication because it is based on a new material that does not need potentially harmful post-process crosslinking and allows the direct encapsulation of cells staying viable throughout the print process. KW - 3D-Druck KW - Elektrospinnen KW - 3D Bioprinting KW - Melt Electrowriting KW - Biofabrication Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-173444 ER - TY - THES A1 - Brückner [geb. Christel], Theresa T1 - Novel application forms and setting mechanisms of mineral bone cements T1 - Neuartige Anwendungsformen und Abbindemechanismen mineralischer Knochenzemente N2 - Calcium phosphate cements (CPC) represent valuable synthetic bone grafts, as they are self-setting, biocompatible, osteoconductive and in their composition similar to the inorganic phase of human bone. Due to their long shelf-life, neutral setting and since water is sufficient for setting, hydroxyapatite (HA) forming cements are processed in different paste formulations. Those comprise dual setting, Ca2+ binding and premixed cement systems. With dual setting formulations, both dissolution and precipitation of the cement raw powder occur simultaneously to the polymerization of water-soluble monomers to form a hydrogel. Chelating agents are able to form complexes with Ca2+ released from the raw powder. Premixed systems mostly contain the raw powder of the cement and a non-aqueous binder liquid which delays the setting reaction until application in the moist physiological environment. In the present work, two of those reaction mechanisms allowed the development of HA based cement applications. Drillable cements are of high clinical interest, as the quality of screw and plate osteosynthesis techniques can be improved by cement augmentation. A drillable, dual setting composite from HA and a poly(2-hydroxyethyl methacrylate) hydrogel was analyzed with respect to the influence of monomer content and powder-to-liquid ratio on setting kinetics and mechanical outcome. While the conversion to HA and crystal growth were constantly confined with increased monomer amount, a minimum concentration of 50 % was required to see impressive ameliorations including a low bending modulus and high fracture energy at improved bending strength. Increasing the liquid amount enabled injection of the paste as well as drilling after 10 min of pre-setting. While classic bone wax formulations have drawbacks such as infection, inflammation, hindered osteogenesis and a lack of biodegradability, the as-presented premixed formulation is believed to exhibit outmatching properties. It consisted of HA raw powders and a non-aqueous, but water-miscible carrier liquid from poly(ethylene glycol) (PEG). The bone wax was proved to be cohesive and malleable, it withstood blood pressure conditions and among deposition in an aqueous environment, PEG was exchanged such that porous, nanocrystalline HA was formed. Incorporation of a model antibiotic proved the suitability of the novel bone wax formulation for drug release purposes. Prefabricated laminates from premixed carbonated apatite forming cement and poly(ε-caprolactone) fiber mats with defined pore architecture were presented as a potential approach for the treatment of 2-dimensional, curved cranial defects. They are flexible until application and were produced in a layer-by-layer approach from both components such that the polymer scaffold prevents the cement from flowing. It was demonstrated that solution electrospinning with a patterned collector for the fabrication of perforated fiber mats was suitable, as high fiber volume contents in combination with an appropriate interface enabled the successful fabrication of mechanically reinforced laminates. Mild immersion of the scaffolds under alkaline conditions additionally improved the interphase followed by an increase in bending-strength. Since few years, magnesium phosphate cements (MPC) have attracted increasing attention for bone replacement. Compared to CPC, MPC exhibit a higher degradation potential and high early strength and they release biologically valuable Mg2+. However, common systems offer some challenges while using them in non-classic cement formulations such as the need for foreign ion supply, the potential acidity of the reaction or the fast setting kinetics. Here, it was possible to develop a chelate-setting MPC paste with a broad spectrum of potential applications. The general mechanism of the novel setting principle was tested in a proof-of-principle manner. The cement paste consisted of farringtonite with differently concentrated phytic acid solution for chelate formation with Mg2+ from the raw powder. Adjusting the phytic acid content and adding a magnesium oxide as setting regulator to compensate its retarding effect resulted in drillable formulations. Additionally, there is a strong clinical demand for well working bone adhesives especially in a moist environment. Mostly the existing formulations are non-biodegradable. Ex vivo adhesion of the above presented MPC under wet conditions on bone demonstrated over a course of 7 d shear strengths of 0.8 MPa. Further, the hardened cement specimens showed a mass loss of 2 wt.% within 24 d in an aqueous environment and released about 0.17 mg/g of osteogenic Mg2+ per day. Together with the demonstrated cytocompatibility towards human fetal osteoblasts, this cement system showed promising characteristics in terms of degradable biocements with special application purposes. N2 - Calciumphosphatzemente (CPC) stellen ein bedeutsames Knochenersatzmaterial dar, da sie selbstabbindend, biokompatibel, osteokonduktiv und der anorganischen Komponente humanen Knochens ähnlich sind. Durch ihre Lagerstabilität, neutrale Abbindereaktion und da Wasser zum Abbinden ausreicht, werden Hydroxylapatit (HA) bildende Zemente in dual abbindenden, Ca2+ chelatisierenden und vorgefertigten Zementen, verarbeitet. Bei dual abbindenden Formulierungen findet die Lösungs-Fällungs-Reaktion zeitgleich zur Polymerisation wasserlöslicher Monomere zu einem Hydrogel statt. Chelatbildner können mit aus dem Rohpulver freigesetzten Ca2+ Komplexe bilden. Vorgefertigte Zemente enthalten eine nicht-wässrige Trägerflüssigkeit, welche die Abbindereaktion bis zur Anwendung des Zements im feuchten Milieu verzögert. In der vorliegenden Arbeit wurden zwei dieser Reaktionsmechanismen zur Entwicklung HA basierter Anwendungsformen eingesetzt. Bohrbare Zemente sind von klinischem Interesse, da die Qualität einer Schrauben- oder Plattenosteosynthese durch Augmentation mit Zement verbessert werden kann. Bei einem bohrbaren, dual abbindenden Komposit aus HA und einem Poly-2-Hydroxyethylmethacrylat Hydrogel wurde der Einfluss des Monomergehalts und des Pulver-zu-Flüssigkeits-Verhältnisses auf die Abbindekinetik und mechanischen Eigenschaften untersucht. Während die Umwandlung zu HA und das Kristallwachstum mit zunehmendem Monomergehalt reduziert wurden, war eine minimale Konzentration von 50 % nötig, um signifikante Verbesserungen des Bruchverhaltens im Sinne eines niedrigen Biegemoduls und einer hohen Bruchenergie bei gesteigerter Biegefestigkeit nachzuweisen. Wurde der Flüssigkeitsgehalt erhöht, so konnte die Paste injiziert und nach 10 min des Abbindens gebohrt werden. Während klassische Knochenwachsformulierungen Infektionen, Entzündungen, gehinderte Knochenneubildung und mangelhafte Bioabbaubarkeit vorweisen, zeigt die hier dargestellte Formulierung überlegene Eigenschaften. Sie bestand aus HA-Rohpulvern und einer nicht-wässrigen, mit Wasser mischbaren Trägermasse aus Polyethylenglycol (PEG). Es wurde gezeigt, dass das Wachs kohäsiv und knetbar ist und Blutdruckbedingungen standhält. Bei Kontakt mit einer wässrigen Phase wurde das PEG diffusiv mit Wasser ausgetauscht, so dass ein poröser, nanokristalliner HA präzipitierte. Die Einbettung eines Modell-Antibiotikums bestätigte zudem die Eignung des neuartigen Wachses als Wirkstoffdepot. Als eine mögliche Behandlung von 2-dimensionalen, gekrümmten Defekten der Schädeldecke wurden präfabrizierte Laminate aus lagerstabiler, Carbonatapatit bildender Zementpaste und Polycaprolakton-Fasermatten mit definierter Porenarchitektur vorgestellt. Diese sind bis zu ihrer Anwendung flexibel und wurden durch einen schichtweisen Aufbau aus beiden Komponenten erzeugt, so dass der Polymerscaffold den Zement am Zerfließen hindert. Es wurde gezeigt, dass die Herstellung makroporöser Fasermatten durch Elektrospinnen aus der Lösung mittels eines perforierten Kollektors geeignet war, da der hohe Faservolumengehalt und angemessene Grenzflächeneigenschaften die erfolgreiche Herstellung mechanisch verstärkter Laminate ermöglichte. Bei milder Behandlung der Scaffolds mit alkalischer Lösung wurden die Grenzflächeneigenschaften weiter verbessert, was zu einer Steigerung der Biegefestigkeit führte. Seit einigen Jahren geht der Trend der Knochenzementforschung immer stärker in Richtung von Magnesiumphosphatzementen (MPC), da diese verglichen mit CPC ein erhöhtes Degradationspotential, eine hohe initiale Festigkeit, sowie die Freisetzung biologisch wertvoller Mg2+ aufweisen. Jedoch stellen gängige Systeme hohe Anforderungen bei der Verwendung in nicht-klassischen Zementen wie z.B. der Bedarf an Fremdionen und die saure sowie schnelle Abbindereaktion. Dennoch war es möglich, einen chelatisierenden MPC zu entwickeln, welcher ein breites Spektrum an möglichen Anwendungsformen bot. In einer Machbarkeitsstudie wurde untersucht, ob das Abbindeprinzip funktioniert. Die Paste bestand aus Farringtonit und unterschiedlich konzentrierter Phytinsäure. Diese sollte mit freigesetzten Mg2+ komplexieren. Durch Anpassung der Phytinsäurekonzentration und Zugabe von Magnesiumoxid als Abbindemodulator wurden bohrbare Formulierungen erhalten. Neben der Bohrbarkeit sind auch adhäsive Eigenschaften der Zemente im feuchten Milieu von klinischem Interesse, wobei kommerziell erhältliche Systeme meist nicht bioabbaubar sind. Daher wurde die ex vivo Klebehaftung dieses MPC nach 7 d unter nassen Bedingungen auf Knochen analysiert, wobei sich eine Abscherfestigkeit von 0.8 MPa ergab. Des Weiteren zeigten diese Zemente einen Masseverlust von 2 Gew.% innerhalb von 24 d in wässriger Umgebung, sowie die Freisetzung von 0.17 mg/g an osteogenen Mg2+ pro Tag. Zusammen mit der bestätigten Zytokompatibilität bezüglich humaner fetaler Osteoblasten ist dieses System vielversprechend für die Anwendung als abbaubarer Biozement für unterschiedliche klinische Zwecke. KW - Knochenzement KW - Calciumphosphat KW - Magnesiumphosphate KW - Verbundwerkstoff KW - Chelatbildner KW - dual setting KW - dual abbindend KW - premixed KW - präfabriziert KW - bone wax KW - Knochenwachs KW - drillable KW - bohrbar KW - bone adhesive KW - Knochenkleber Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-157045 ER - TY - THES A1 - Schäfer [geb. Stichler], Simone T1 - Thiol-ene Cross-linked Poly(glycidol) / Hyaluronic Acid Based Hydrogels for 3D Bioprinting T1 - Thilo-En vernetzte Hydrogele basierend auf Poly(glyzidolen) und Hyaluronsäure für das 3D-Biodrucken N2 - The aim of the work was the development of thiol-ene cross-linked hydrogels based on functionalized poly(glycidol)s (PG) and hyaluronic acid (HA) for extrusion based 3D bioprinting. Additionally, the functionalization of the synthesized PG with peptides and the suitability of these polymers for physically cross-linked gels were investigated, in a proof of principle study in order to demonstrate the versatile use of PG polymers in hydrogel development. First, the precursor polymers of the different hydrogel systems were synthesized. For thiol-ene cross-linked hydogels, linear allyl-functionalized PG (P(AGE-co-G)) and three different thiol-(SH-)functionalized polymers, ester-containing PG-SH (PG SHec), ester-free PG-SH (PG-SHef) and HA-SH were synthesized and analysed, The degree of functionalization of these polymers was adjustable. For physically cross-linked hydrogels, peptide-functionalized PG (P(peptide-co-G)), was synthesized through polymer analogue thiol-ene modification of P(AGE-co-G). Subsequently, thiol-ene cross-linked hydrogels were prepared with the synthesized thiol- and allyl-functionalized polymers. Depending on the origin of the used polymers, two different systems were obtained: on the one hand synthetic hydrogels consisting of PG-SHec/ef and P(AGE-co-G) and on the other hand hybrid gels, consisting of HA-SH and P(AGE-co-G). In synthetic gels, the degradability of the gels was determined by the applied PG-SH. The use of PG-SHec resulted in hydrolytically degradable hydrogels, whereas the cross-linking with PG-SHef resulted in non-degradable gels. The physical properties of these different hydrogel systems were determined by swelling, mechanical and diffusion studies and subsequently compared among each other. In swelling studies the differences of degradable and non-degradable synthetic hydrogels as well as the differences of synthetic compared to hybrid hydrogels were demonstrated. Next, the stiffness and the swelling ratios (SR) of the established hydrogel systems were examined in dependency of different parameters, such as incubation time, polymer concentration and UV irradiation. In general, these measurements revealed the same trends for synthetic and hybrid hydrogels: an increased polymer concentration as well as prolonged UV irradiation led to an increased network density. Moreover, it was demonstrated that the incorporation of additional non-bound HMW HA hampered the hydrogel cross-linking resulting in gels with decreased stiffness and increased SR. This effect was strongly dependent on the amount of additional HMW HA. The diffusion of different molecular weight fluorescein isothiocyanate-dextran (FITC-dextran) through hybrid hydrogels (with/without HMW HA) gave information about the mesh size of these gels. The smallest FITC-dextran (4 kDa) completely diffused through both hydrogel systems within the first week, whereas only 55 % of 40 kDa and 5-10 % HMW FITC-dextrans (500 kDa and 2 MDa) could diffuse through the networks. The applicability of synthetic and hybrid hydrogels for cartilage regeneration purpose was investigated through by biological examinations. It was proven that both gels support the survival of embedded human mesenchymal stromal cells (hMSCs) (21/28 d in vitro culture), however, the chondrogenic differentiation was significantly improved in hybrid hydrogels compared to synthetic gels. The addition of non-bound HMW HA resulted in a slightly less distinct chondrogenesis. Lastly the printability of the established hydrogel systems was examined. Therefore, the viscoelastic properties of the hydrogel solutions were adjusted by incorporation of non-bound HMW HA. Both systems could be successfully printed with high resolution and high shape fidelity. The introduction of the double printing approach with reinforcing PCL allowed printing of hydrogel solutions with lower viscosities. As a consequence, the amount of additional HMW HA necessary for printing could be reduced allowing successful printing of hybrid hydrogel solutions with embedded cells. It was demonstrated that the integrated cells survived the printing process with high viability measured after 21 d. Moreover, by this reinforcing technique, robust hydrogel-containing constructs were fabricated. In addition to thiol-ene cross-linked hydrogels, hydrogel cross-linking via ionic interactions was investigated with a hybrid hydrogel based on HMW HA and peptide-functionalized PG. Rheological measurements revealed an increase in the viscosity of a 2 wt.% HMW HA solution by the addition of peptide-functionalized PG. The increase in viscosity could be attributed to the ionic interactions between the positively charge PG and the negatively charge HMW HA. In conclusion, throughout this thesis thiol-ene chemistry and PG were introduced as promising cross-linking reaction and polymer precursor for the field of biofabrication. Furthermore, the differences of hybrid and synthetic hydrogels as well as chemically and physically cross-linked hydrogels were demonstrated. Moreover, the double printing approach was demonstrated to be a promising tool for the fabrication of robust hydrogel-containing constructs. It opens the possibility of printing hydrogels that were not printable yet, due to too low viscosities. N2 - Ziel der Arbeit war die Entwicklung von Thiol-En-vernetzten Hydrogelen basierend auf funktionalisierten Poly(glyzidolen) (PG) und Hyaluronsäure (HA) für das extrusionsbasierte 3D-Biodrucken. Um die vielseitigen Anwendungsmöglichkeiten von PG-Polymeren für die Hydrogelentwicklung zu zeigen, wurde darüber hinaus, in einer Proof-of-Principle-Studie, PG mit Peptiden funktionalisiert und die Eignung dieser Polymere für die Herstellung von physikalisch vernetzten Gelen untersucht. Zunächst wurden die Vorläuferpolymere für die verschiedenen Hydrogelsysteme synthetisiert. Für die Thiol-En-vernetzten Hydrogele wurde lineares Allyl-funktionalisiertes PG (P(AGE-co-G)) und drei verschiedene Thiol-(SH )funktionalisierte Polymere, Ester haltiges PG-SH (PG-SHec), Ester freies PG SH (PG-SHef) und HA-SH synthetisiert und analysiert. Dabei war der Funktionalisierungsgrad dieser Polymere einstellbar. Für physikalisch vernetzte Hydrogele wurde Peptid-funktionalisierte PGs (P(Peptid co-G)) mittels polymeranaloger Thiol-En-Modifikation von P(AGE-co-G) synthetisiert. Anschließend wurden Thiol-En-vernetzte Hydrogele auf Basis der synthetisierten Thiol- und Allyl-funktionalisierten Polymeren hergestellt. Je nach Ursprung der verwendeten Polymere wurden zwei verschiedene Systeme erhalten: einerseits synthetische Hydrogele bestehend aus PG-SHec/ef und P(AGE-co-G) und andererseits hybride Gele, bestehend aus HA-SH und P(AGE-co-G). Bei den synthetischen Gelen wurde die Abbaubarkeit der Gele durch das verwendete PG-SH bestimmt. Die Verwendung von PG-SHec resultierte in hydrolytisch abbaubaren Hydrogelen, während die Vernetzung mit PG-SHef zu nicht abbaubaren Gelen führte. Die physikalischen Eigenschaften der verschiedenen Hydrogelsysteme wurden mittels Quell-, mechanischen und Diffusionsexperimenten bestimmt und anschließend miteinander verglichen. Die Quellungsstudien zeigten die Unterschiede von abbaubaren und nicht abbaubaren synthetischen Hydrogelen, sowie die Unterschiede von synthetischen gegenüber hybriden Hydrogelen. Als nächstes wurden die Steifigkeit und das Quellverhältnis (SR) der etablierten Hydrogelsysteme in Abhängigkeit von verschiedenen Parametern wie Inkubationszeit, Polymerkonzentration und UV-Bestrahlung untersucht. Im Allgemeinen zeigten diese Messungen für synthetische und hybride Hydrogele die gleichen Trends: eine erhöhte Polymerkonzentration sowie eine verlängerte UV-Bestrahlung führten zu einer erhöhten Netzwerkdichte. Darüber hinaus wurde gezeigt, dass das Einbringen zusätzlicher, nicht gebundener HMW HA die Hydrogelvernetzung behinderte, was zu Gelen mit verringerter Steifigkeit und erhöhtem SR führte. Dieser Effekt war stark abhängig von der Menge an zusätzlich eingebrachter HMW HA. Die Diffusion von Fluorescein-Isothiocyanat-Dextran (FITC-Dextran) mit unterschiedlichem Molekulargewichten durch hybride Hydrogele (mit/ohne HMW HA) lieferte Informationen über die Maschengröße dieser Gele. Das kleinste FITC-Dextran (4 kDa) diffundierte innerhalb der ersten Woche vollständig durch beide Hydrogelsysteme, während nur 55 % der 40 kDa und 5-10 % HMW FITC-Dextrane (500 kDa und 2 MDa) durch die Netzwerke diffundieren konnten. Die Anwendbarkeit von synthetischen und hybriden Hydrogelen für Knorpelregenerationszwecke wurde durch biologische Experimente untersucht. Es wurde bewiesen, dass beide Gele das Überleben von eingebetteten humanen mesenchymalen Stromazellen (hMSCs) unterstützen (21/28 d in vitro Kultur), jedoch war die chondrogene Differenzierung in hybriden Hydrogelen im Vergleich zu synthetischen Gelen signifikant verbessert. Die Zugabe von nicht gebundenem HMW HA führte zu einer etwas weniger ausgeprägten Chondrogenese. Zuletzt wurde die Druckbarkeit der etablierten Hydrogelsysteme untersucht. Dafür wurden die viskoelastischen Eigenschaften der Hydrogellösungen durch das Einbringen von nicht gebundener HMW HA eingestellt. Beide Systeme konnten erfolgreich mit hoher Auflösung und hoher Formgenauigkeit gedruckt werden. Die Einführung des Doppeldruck-Konzeptes mit verstärkendem PCL ermöglichte das Drucken von Hydrogellösungen mit niedrigeren Viskositäten. Infolgedessen konnte die für den Druck notwendige Menge an HMW HA reduziert und hybride Hydrogellösungen mit eingebetteten Zellen erfolgreich gedruckt werden. Es wurde gezeigt, dass die integrierten Zellen den Druckprozess mit hoher Vitalität überlebten (gemessen nach 21 d). Darüber hinaus wurden mit dieser Verstärkungstechnik robuste Hydrogel-enthaltende Konstrukte hergestellt. Zusätzlich zu den Thiol-En-vernetzten Hydrogelen wurde die Hydrogelvernetzung mittels elektrostatischen Wechselwirkungen mit einem hybriden Gel auf der Basis von HMW HA und Peptid-funktionalisiertem PG untersucht. Rheologische Messungen ergaben eine Erhöhung der Viskosität einer 2 wt.% HMW HA Lösungen durch die Zugabe von Peptid-funktionalisiertem PG. Der Viskositätsanstieg konnte auf die elektrostatischen Wechselwirkungen zwischen dem positiv geladenen PG und der negativ geladenen HMW HA zurückgeführt werden. Zusammenfassend wurde in dieser Arbeit die Thiol-En-Chemie und PG als vielversprechende Vernetzungsreaktion bzw. Polymervorstufe für die Biofabrikation eingeführt. Des Weiteren wurden die Unterschiede von hybriden und synthetischen Hydrogelen sowie von chemisch und physikalisch vernetzten Hydrogelen aufgezeigt. Darüber hinaus wurde gezeigt, dass das Doppeldruck-Konzept eine vielversprechende Methode für die Herstellung von robusten Hydrogel-enthaltenden Konstrukten ist. Es eröffnet die Möglichkeit, Hydrogele zu drucken, die aufgrund zu geringer Viskositäten bis jetzt nicht druckbar waren. KW - Hyaluronsäure KW - thiol-ene KW - Hyaluronic Acid KW - poly(glycidol) KW - hydrogels KW - Hydrogel KW - Glycidol KW - 3D-Druck KW - 3D printing Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-174713 ER -