TY - THES A1 - Baunach, Marcel T1 - Advances in Distributed Real-Time Sensor/Actuator Systems Operation - Operating Systems, Communication, and Application Design Concepts - T1 - Fortschritte im Betrieb drahtloser Sensor/Aktuator Netzwerke N2 - This work takes a close look at several quite different research areas related to the design of networked embedded sensor/actuator systems. The variety of the topics illustrates the potential complexity of current sensor network applications; especially when enriched with actuators for proactivity and environmental interaction. Besides their conception, development, installation and long-term operation, we'll mainly focus on more "low-level" aspects: Compositional hardware and software design, task cooperation and collaboration, memory management, and real-time operation will be addressed from a local node perspective. In contrast, inter-node synchronization, communication, as well as sensor data acquisition, aggregation, and fusion will be discussed from a rather global network view. The diversity in the concepts was intentionally accepted to finally facilitate the reliable implementation of truly complex systems. In particular, these should go beyond the usual "sense and transmit of sensor data", but show how powerful today's networked sensor/actuator systems can be despite of their low computational performance and constrained hardware: If their resources are only coordinated efficiently! N2 - Diese Arbeit behandelt einige sehr unterschiedliche Forschungsbereiche bezüglich des Designs vernetzter und eingebetteter Sensor/Aktuator-Systeme. Die Vielfalt der Themen zeigt die potenzielle Komplexität aktueller Sensornetzwerk-Anwendungen, insbesondere wenn sie mit Aktuatoren zur Interaktion mit der Umwelt ausgestattet sind. Neben deren Konzeption, Entwicklung, Installation und dem langfristigen Betrieb wird besonders auf diverse "low-level" Aspekte eingegangen: Kompositionelles Hardware- und Software-Design, Task Kooperation und Kollaboration, Speicher-Verwaltung und Echtzeit-Betrieb werden aus lokaler Sicht der Sensorknoten betrachtet. Im Kontrast werden Knoten-Synchronisation, Kommunikation, sowie Sensordatenerfassung, -aggregation und -fusion aus globaler Netzwerk-Sicht diskutiert. Die Vielfalt der behandelten Konzepte wurde bewusst in Kauf genommen, um letztlich die zuverlässige Umsetzung sehr komplexer Systeme zu erleichtern. Insbesondere sollte dies über das übliche "Erfassen und Übertragen von Sensordaten" hinausgehen, und zeigen, wie mächtig heutige vernetzte Sensor/Aktuator-Systeme trotz ihrer geringen Rechenleistung und eingeschränkten Hardware sein können: Wenn ihre Ressourcen effizient koordiniert werden! KW - Eingebettetes System KW - Drahtloses Sensorsystem KW - Echtzeitsystem KW - Dynamische Speicherverwaltung KW - Ressourcenallokation KW - Fernwartung KW - Betriebssystem KW - Verteiltes System KW - Lokalisation KW - Embedded Systems KW - Real-Time Operating Systems KW - Localization KW - Wireless Sensor/Actuator Systems KW - Dynamic Memory Management Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-76489 ER - TY - JOUR A1 - Bayer, Daniel A1 - Pruckner, Marco T1 - A digital twin of a local energy system based on real smart meter data JF - Energy Informatics N2 - The steadily increasing usage of smart meters generates a valuable amount of high-resolution data about the individual energy consumption and production of local energy systems. Private households install more and more photovoltaic systems, battery storage and big consumers like heat pumps. Thus, our vision is to augment these collected smart meter time series of a complete system (e.g., a city, town or complex institutions like airports) with simulatively added previously named components. We, therefore, propose a novel digital twin of such an energy system based solely on a complete set of smart meter data including additional building data. Based on the additional geospatial data, the twin is intended to represent the addition of the abovementioned components as realistically as possible. Outputs of the twin can be used as a decision support for either system operators where to strengthen the system or for individual households where and how to install photovoltaic systems and batteries. Meanwhile, the first local energy system operators had such smart meter data of almost all residential consumers for several years. We acquire those of an exemplary operator and discuss a case study presenting some features of our digital twin and highlighting the value of the combination of smart meter and geospatial data. KW - digital twin KW - simulation KW - local energy system KW - decision support system KW - smart meter data utilization KW - future energy grid exploration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-357456 VL - 6 ER - TY - JOUR A1 - Becker, Martin A1 - Caminiti, Saverio A1 - Fiorella, Donato A1 - Francis, Louise A1 - Gravino, Pietro A1 - Haklay, Mordechai (Muki) A1 - Hotho, Andreas A1 - Loreto, Virrorio A1 - Mueller, Juergen A1 - Ricchiuti, Ferdinando A1 - Servedio, Vito D. P. A1 - Sirbu, Alina A1 - Tria, Franesca T1 - Awareness and Learning in Participatory Noise Sensing JF - PLOS ONE N2 - The development of ICT infrastructures has facilitated the emergence of new paradigms for looking at society and the environment over the last few years. Participatory environmental sensing, i.e. directly involving citizens in environmental monitoring, is one example, which is hoped to encourage learning and enhance awareness of environmental issues. In this paper, an analysis of the behaviour of individuals involved in noise sensing is presented. Citizens have been involved in noise measuring activities through the WideNoise smartphone application. This application has been designed to record both objective (noise samples) and subjective (opinions, feelings) data. The application has been open to be used freely by anyone and has been widely employed worldwide. In addition, several test cases have been organised in European countries. Based on the information submitted by users, an analysis of emerging awareness and learning is performed. The data show that changes in the way the environment is perceived after repeated usage of the application do appear. Specifically, users learn how to recognise different noise levels they are exposed to. Additionally, the subjective data collected indicate an increased user involvement in time and a categorisation effect between pleasant and less pleasant environments. KW - exposure Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-127675 SN - 1932-6203 VL - 8 IS - 12 ER - TY - JOUR A1 - Bencurova, Elena A1 - Shityakov, Sergey A1 - Schaack, Dominik A1 - Kaltdorf, Martin A1 - Sarukhanyan, Edita A1 - Hilgarth, Alexander A1 - Rath, Christin A1 - Montenegro, Sergio A1 - Roth, Günter A1 - Lopez, Daniel A1 - Dandekar, Thomas T1 - Nanocellulose composites as smart devices with chassis, light-directed DNA Storage, engineered electronic properties, and chip integration JF - Frontiers in Bioengineering and Biotechnology N2 - The rapid development of green and sustainable materials opens up new possibilities in the field of applied research. Such materials include nanocellulose composites that can integrate many components into composites and provide a good chassis for smart devices. In our study, we evaluate four approaches for turning a nanocellulose composite into an information storage or processing device: 1) nanocellulose can be a suitable carrier material and protect information stored in DNA. 2) Nucleotide-processing enzymes (polymerase and exonuclease) can be controlled by light after fusing them with light-gating domains; nucleotide substrate specificity can be changed by mutation or pH change (read-in and read-out of the information). 3) Semiconductors and electronic capabilities can be achieved: we show that nanocellulose is rendered electronic by iodine treatment replacing silicon including microstructures. Nanocellulose semiconductor properties are measured, and the resulting potential including single-electron transistors (SET) and their properties are modeled. Electric current can also be transported by DNA through G-quadruplex DNA molecules; these as well as classical silicon semiconductors can easily be integrated into the nanocellulose composite. 4) To elaborate upon miniaturization and integration for a smart nanocellulose chip device, we demonstrate pH-sensitive dyes in nanocellulose, nanopore creation, and kinase micropatterning on bacterial membranes as well as digital PCR micro-wells. Future application potential includes nano-3D printing and fast molecular processors (e.g., SETs) integrated with DNA storage and conventional electronics. This would also lead to environment-friendly nanocellulose chips for information processing as well as smart nanocellulose composites for biomedical applications and nano-factories. KW - nanocellulose KW - DNA storage KW - light-gated proteins KW - single-electron transistors KW - protein chip Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-283033 SN - 2296-4185 VL - 10 ER - TY - THES A1 - Betz, Christian T1 - Scalable authoring of diagnostic case based training systems T1 - Skalierbare Erstellung diagnostischer fallbasierter Trainingssysteme N2 - Diagnostic Case Based Training Systems (D-CBT) provide learners with a means to learn and exercise knowledge in a realistic context. In medical education, D-CBT Systems present virtual patients to the learners who are asked to examine, diagnose and state therapies for these patients. Due a number of conflicting and changing requirements, e.g. time for learning, authoring effort, several systems were developed so far. These systems range from simple, easy-to-use presentation systems to highly complex knowledge based systems supporting explorative learning. This thesis presents an approach and tools to create D-CBT systems from existing sources (documents, e.g. dismissal records) using existing tools (word processors): Authors annotate and extend the documents to model the knowledge. A scalable knowledge representation is able to capture the content on multiple levels, from simple to highly structured knowledge. Thus, authoring of D-CBT systems requires less prerequisites and pre-knowledge and is faster than approaches using specialized authoring environments. Also, authors can iteratively add and structure more knowledge to adapt training cases to their learners needs. The theses also discusses the application of the same approach to other domains, especially to knowledge acquisition for the Semantic Web. N2 - Fallbasierte diagnostische Trainingssysteme (FDT) ermöglichen es Lernern, Wissen durch Anwendung in einem realistischen Kontext zu erwerben und zu festigen. In der medizinischen Ausbildung präsentieren FDT Systeme virtuelle Patienten, an denen der Lerner die Auswahl und Interpretation der richtigen Untersuchungen, die Diagnostik und die Bestimmung geeigneter Therapien erlernen und üben kann. Eine Vielzahl von Anforderungen durch die Lerner und die Autoren solcher Systeme hat zur Entwicklung unterschiedlicher Trainingsumgebungen geführt. Darunter gibt es einfache, präsentationsorientierte Systeme ebenso wie komplexe wissensbasierte Systeme, die exploratives Lernern erlauben. Diese Dissertation untersucht einen Ansatz und Werkzeuge, um FDT Systeme aus vorhandenen Daten (d.h. Dokumenten, beispielsweise Entlassschreiben) und mit Hilfe bekannter Werkzeuge (d.h. Textverarbeitung) zu entwickeln: Die Autoren annotieren dazu die Dokumente, um die Fälle zu modellieren. Eine skalierbare Wissensrepräsentation kann das so extrahierte Wissen auf verschiedenen Ebenen erfassen, angefangen mit unstrukturierten Elementen bis zu Wissensmodellen mit kausalen Beziehungen. Autoren können mit Hilfe des vorgestellten Ansatzes fallbasierte diagnostische Trainingssysteme mit geringerem Vorwissen und schneller erstellen als mit Hilfe spezialisierter Autorensysteme. Dabei können die Autoren insbesondere die Fälle sukzessive mit weiterem Wissen anreichern und so auf die Anforderungen ihrer Lerner anpassen. In der Dissertation wird darüber hinaus die Anwendung des Ansatzes und der entstandenen Werkzeuge auf andere Domänen untersucht. Besonders interessant ist dabei die Anwendung in der Wissensakquisition für das Semantic Web. KW - Computerunterstütztes Lernen KW - Medizin KW - Wissensrepräsentation KW - Trainingssystem KW - agile Prozesse KW - Semantic Web KW - d3web.Train KW - knowledge representation KW - training systems KW - agile processes KW - semantic web KW - d3web.Train Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-17885 ER - TY - THES A1 - Binder, Andreas T1 - Die stochastische Wissenschaft und zwei Teilsysteme eines Web-basierten Informations- und Anwendungssystems zu ihrer Etablierung T1 - The stochastic science and two subsystems of a web-based information and application system for its establishment N2 - Das stochastische Denken, die Bernoullische Stochastik und dessen informationstechnologische Umsetzung, namens Stochastikon stellen die Grundlage für das Verständnis und die erfolgreiche Nutzung einer stochastischen Wissenschaft dar. Im Rahmen dieser Arbeit erfolgt eine Klärung des Begriffs des stochastischen Denkens, eine anschauliche Darstellung der von Elart von Collani entwickelten Bernoullischen Stochastik und eine Beschreibung von Stochastikon. Dabei werden sowohl das Gesamtkonzept von Stochastikon, sowie die Ziele, Aufgaben und die Realisierung der beiden Teilsysteme namens Mentor und Encyclopedia vorgestellt. Das stochastische Denken erlaubt eine realitätsnahe Sichtweise der Dinge, d.h. eine Sichtweise, die mit den menschlichen Beobachtungen und Erfahrungen im Einklang steht und somit die Unsicherheit über zukünftige Entwicklungen berücksichtigt. Der in diesem Kontext verwendete Begriff der Unsicherheit bezieht sich ausschließlich auf zukünftige Entwicklungen und äußert sich in Variabilität. Quellen der Unsicherheit sind einerseits die menschliche Ignoranz und andererseits der Zufall. Unter Ignoranz wird hierbei die Unwissenheit des Menschen über die unbekannten, aber feststehenden Fakten verstanden, die die Anfangsbedingungen der zukünftigen Entwicklung repräsentieren. Die Bernoullische Stochastik liefert ein Regelwerk und ermöglicht die Entwicklung eines quantitativen Modells zur Beschreibung der Unsicherheit und expliziter Einbeziehung der beiden Quellen Ignoranz und Zufall. Das Modell trägt den Namen Bernoulli-Raum und bildet die Grundlage für die Herleitung quantitativer Verfahren, um zuverlässige und genaue Aussagen sowohl über die nicht-existente zufällige Zukunft (Vorhersageverfahren), als auch über die unbekannte feststehende Vergangenheit (Messverfahren). Das Softwaresystem Stochastikon implementiert die Bernoullische Stochastik in Form einer Reihe autarker, miteinander kommunizierender Teilsysteme. Ziel des Teilsystems Encyclopedia ist die Bereitstellung und Bewertung stochastischen Wissens. Das Teilsystem Mentor dient der Unterstützung des Anwenders bei der Problemlösungsfindung durch Identifikation eines richtigen Modells bzw. eines korrekten Bernoulli-Raums. Der Lösungsfindungsprozess selber enthält keinerlei Unsicherheit. Die ganze Unsicherheit steckt in der Lösung, d.h. im Bernoulli-Raum, der explizit die vorhandene Unwissenheit (Ignoranz) und den vorliegenden Zufall abdeckend enthält. N2 - Stochastic thinking, Bernoulli stochastics and its information technological realization, called Stochastikon, represent the basis for understanding and successfully utilizing stochastic science. This thesis defines the concept of stochastic thinking, introduces Bernoulli stochastics, which has been developed by Elart von Collani, and describes the IT system Stochastikon. The concept and the design of Stochastikon are outlined and the aims, tasks and realizations of the two subsystems Mentor and Encyclopedia are given in detail. Stochastic thinking enables a realistic view of reality. This means a view, which is in agreement with observation and experience and, thus, takes into account uncertainty about future developments. In this context the term of uncertainty is used exclusively with respect to future development and materializes in variability. Sources of uncertainty are on the one hand human ignorance about fixed facts on the one hand and randomness on the other. Bernoulli stochastics makes available a set of rules for developing a quantitative model about uncertainty taking particularly into account the two sources ignorance and randomness. The model is called Bernoulli-Space, which is the basis for reliable and precise quantitative procedures for statements about the random future (prediction procedures) as well as about the unknown fixed past (measurement procedures). The software system, called Stochastikon, implements Bernoulli stochastics based on a set of self-sustained intercommunicating subsystems. The Subsystem Encyclopedia makes stochastical knowledge available, while the Subsystem Mentor supports the user for solving (stochastic) problems by identifying the correct model respectively correct Bernoulli-Space. The problem solving process is free of uncertainty, because all uncertainty is modelled by Bernoulli-space. KW - Stochastik KW - stochastisches Denken KW - Bernoullische Stochastik KW - Bernoulli-Raum KW - Stochastikon KW - stochastic thinking KW - Bernoulli stochastics KW - Bernoullispace KW - Stochastikon Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-26146 ER - TY - THES A1 - Binzenhöfer, Andreas T1 - Performance Analysis of Structured Overlay Networks T1 - Leistungsbewertung Strukturierter Overlay Netze N2 - Overlay networks establish logical connections between users on top of the physical network. While randomly connected overlay networks provide only a best effort service, a new generation of structured overlay systems based on Distributed Hash Tables (DHTs) was proposed by the research community. However, there is still a lack of understanding the performance of such DHTs. Additionally, those architectures are highly distributed and therefore appear as a black box to the operator. Yet an operator does not want to lose control over his system and needs to be able to continuously observe and examine its current state at runtime. This work addresses both problems and shows how the solutions can be combined into a more self-organizing overlay concept. At first, we evaluate the performance of structured overlay networks under different aspects and thereby illuminate in how far such architectures are able to support carrier-grade applications. Secondly, to enable operators to monitor and understand their deployed system in more detail, we introduce both active as well as passive methods to gather information about the current state of the overlay network. N2 - Unter einem Overlay Netz versteht man den Zusammenschluss mehrerer Komponenten zu einer logischen Topologie, die auf einer existierenden physikalischen Infrastruktur aufsetzt. Da zufällige Verbindungen zwischen den einzelnen Teilnehmern aber sehr ineffizient sind, wurden strukturierte Overlay Netze entworfen, bei denen die Beziehungen zwischen den einzelnen Teilnehmern fest vorgeschrieben sind. Solche strukturierten Mechanismen versprechen zwar ein großes Potential, dieses wurde aber noch nicht ausreichend untersucht bzw. wissenschaftlich nachgewiesen. In dieser Arbeit wird mit mathematischen Methoden und ereignisorientierter Simulation die Leistungsfähigkeit von strukturierten Overlay Netzen untersucht. Da diese stark von der aktuellen Situation im Overlay abhängt, entwickeln wir Methoden, mit denen sich sowohl passiv, als auch aktiv, wichtige Systemparameter zur Laufzeit abschätzen bzw. messen lassen. Zusammen führen die vorgeschlagenen Methoden zu selbstorganisierenden Mechanismen, die den aktuellen Zustand des Overlays überwachen, diesen bewerten und sich gegebenenfalls automatisch an die aktuellen Verhältnisse anpassen T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 01/08 KW - Overlay-Netz KW - Leistungsbewertung KW - Peer-to-Peer-Netz KW - Mathematisches Modell KW - Chord KW - Kademlia KW - DHT KW - Overlay KW - Chord KW - Kademlia KW - DHT Y1 - 2007 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-26291 ER - TY - THES A1 - Bleier, Michael T1 - Underwater Laser Scanning - Refractive Calibration, Self-calibration and Mapping for 3D Reconstruction T1 - Laserscanning unter Wasser - Refraktive Kalibrierung, Selbstkalibrierung und Kartierung zur 3D Rekonstruktion N2 - There is great interest in affordable, precise and reliable metrology underwater: Archaeologists want to document artifacts in situ with high detail. In marine research, biologists require the tools to monitor coral growth and geologists need recordings to model sediment transport. Furthermore, for offshore construction projects, maintenance and inspection millimeter-accurate measurements of defects and offshore structures are essential. While the process of digitizing individual objects and complete sites on land is well understood and standard methods, such as Structure from Motion or terrestrial laser scanning, are regularly applied, precise underwater surveying with high resolution is still a complex and difficult task. Applying optical scanning techniques in water is challenging due to reduced visibility caused by turbidity and light absorption. However, optical underwater scanners provide significant advantages in terms of achievable resolution and accuracy compared to acoustic systems. This thesis proposes an underwater laser scanning system and the algorithms for creating dense and accurate 3D scans in water. It is based on laser triangulation and the main optical components are an underwater camera and a cross-line laser projector. The prototype is configured with a motorized yaw axis for capturing scans from a tripod. Alternatively, it is mounted to a moving platform for mobile mapping. The main focus lies on the refractive calibration of the underwater camera and laser projector, the image processing and 3D reconstruction. For highest accuracy, the refraction at the individual media interfaces must be taken into account. This is addressed by an optimization-based calibration framework using a physical-geometric camera model derived from an analytical formulation of a ray-tracing projection model. In addition to scanning underwater structures, this work presents the 3D acquisition of semi-submerged structures and the correction of refraction effects. As in-situ calibration in water is complex and time-consuming, the challenge of transferring an in-air scanner calibration to water without re-calibration is investigated, as well as self-calibration techniques for structured light. The system was successfully deployed in various configurations for both static scanning and mobile mapping. An evaluation of the calibration and 3D reconstruction using reference objects and a comparison of free-form surfaces in clear water demonstrate the high accuracy potential in the range of one millimeter to less than one centimeter, depending on the measurement distance. Mobile underwater mapping and motion compensation based on visual-inertial odometry is demonstrated using a new optical underwater scanner based on fringe projection. Continuous registration of individual scans allows the acquisition of 3D models from an underwater vehicle. RGB images captured in parallel are used to create 3D point clouds of underwater scenes in full color. 3D maps are useful to the operator during the remote control of underwater vehicles and provide the building blocks to enable offshore inspection and surveying tasks. The advancing automation of the measurement technology will allow non-experts to use it, significantly reduce acquisition time and increase accuracy, making underwater metrology more cost-effective. N2 - Das Interesse an präziser, zuverlässiger und zugleich kostengünstiger Unterwassermesstechnik ist groß. Beispielsweise wollen Archäologen Artefakte in situ mit hoher Detailtreue dokumentieren und in der Meeresforschung benötigen Biologen Messwerkzeuge zur Beobachtung des Korallenwachstums. Auch Geologen sind auf Messdaten angewiesen, um Sedimenttransporte zu modellieren. Darüber hinaus ist für die Errichtung von Offshore-Bauwerken, sowie deren Wartung und Inspektion eine millimetergenaue Vermessung von vorhandenen Strukturen und Defekten unerlässlich. Während die Digitalisierung einzelner Objekte und ganzer Areale an Land gut erforscht ist und verschiedene Standardmethoden, wie zum Beispiel Structure from Motion oder terrestrisches Laserscanning, regelmäßig eingesetzt werden, ist die präzise und hochauflösende Unterwasservermessung nach wie vor eine komplexe und schwierige Aufgabe. Die Anwendung optischer Messtechnik im Wasser ist aufgrund der eingeschränkten Sichttiefe durch Trübung und Lichtabsorption eine Herausforderung. Optische Unterwasserscanner bieten jedoch Vorteile hinsichtlich der erreichbaren Auflösung und Genauigkeit gegenüber akustischen Systemen. In dieser Arbeit werden ein Unterwasser-Laserscanning-System und die Algorithmen zur Erzeugung von 3D-Scans mit hoher Punktdichte im Wasser vorgestellt. Es basiert auf Lasertriangulation und die optischen Hauptkomponenten sind eine Unterwasserkamera und ein Kreuzlinienlaserprojektor. Das System ist mit einer motorisierten Drehachse ausgestattet, um Scans von einem Stativ aus aufzunehmen. Alternativ kann es von einer beweglichen Plattform aus für mobile Kartierung eingesetzt werden. Das Hauptaugenmerk liegt auf der refraktiven Kalibrierung der Unterwasserkamera und des Laserprojektors, der Bildverarbeitung und der 3D-Rekonstruktion. Um höchste Genauigkeit zu erreichen, muss die Brechung an den einzelnen Medienübergängen berücksichtigt werden. Dies wird durch ein physikalisch-geometrisches Kameramodell, das auf einer analytischen Beschreibung der Strahlenverfolgung basiert, und ein optimierungsbasiertes Kalibrierverfahren erreicht. Neben dem Scannen von Unterwasserstrukturen wird in dieser Arbeit auch die 3D-Erfassung von teilweise im Wasser befindlichen Strukturen und die Korrektur der dabei auftretenden Brechungseffekte vorgestellt. Da die Kalibrierung im Wasser komplex und zeitintensiv ist, wird die Übertragung einer Kalibrierung des Scanners in Luft auf die Bedingungen im Wasser ohne Neukalibrierung, sowie die Selbstkalibrierung für Lichtschnittverfahren untersucht. Das System wurde in verschiedenen Konfigurationen sowohl für statisches Scannen als auch für die mobile Kartierung erfolgreich eingesetzt. Die Validierung der Kalibrierung und der 3D-Rekonstruktion anhand von Referenzobjekten und der Vergleich von Freiformflächen in klarem Wasser zeigen das hohe Genauigkeitspotenzial im Bereich von einem Millimeter bis weniger als einem Zentimeter in Abhängigkeit von der Messdistanz. Die mobile Unterwasserkartierung und Bewegungskompensation anhand visuell-inertialer Odometrie wird mit einem neuen optischen Unterwasserscanner auf Basis der Streifenprojektion demonstriert. Dabei ermöglicht die kontinuierliche Registrierung von Einzelscans die Erfassung von 3D-Modellen von einem Unterwasserfahrzeug aus. Mit Hilfe von parallel aufgenommenen RGB-Bildern werden dabei farbige 3D-Punktwolken der Unterwasserszenen erstellt. Diese 3D-Karten dienen beispielsweise dem Bediener bei der Fernsteuerung von Unterwasserfahrzeugen und bilden die Grundlage für Offshore-Inspektions- und Vermessungsaufgaben. Die fortschreitende Automatisierung der Messtechnik wird somit auch eine Verwendung durch Nichtfachleute ermöglichen und gleichzeitig die Erfassungszeit erheblich verkürzen und die Genauigkeit verbessern, was die Vermessung im Wasser kostengünstiger und effizienter macht. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 28 KW - Selbstkalibrierung KW - Punktwolke KW - Bildverarbeitung KW - 3D Reconstruction KW - Self-calibration KW - Underwater Scanning KW - Underwater Mapping KW - Dreidimensionale Rekonstruktion KW - 3D-Rekonstruktion Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-322693 SN - 978-3-945459-45-4 ER - TY - THES A1 - Borrmann, Dorit T1 - Multi-modal 3D mapping - Combining 3D point clouds with thermal and color information T1 - Multi-modale 3D-Kartierung - Kombination von 3D-Punktwolken mit Thermo- und Farbinformation N2 - Imagine a technology that automatically creates a full 3D thermal model of an environment and detects temperature peaks in it. For better orientation in the model it is enhanced with color information. The current state of the art for analyzing temperature related issues is thermal imaging. It is relevant for energy efficiency but also for securing important infrastructure such as power supplies and temperature regulation systems. Monitoring and analysis of the data for a large building is tedious as stable conditions need to be guaranteed for several hours and detailed notes about the pose and the environment conditions for each image must be taken. For some applications repeated measurements are necessary to monitor changes over time. The analysis of the scene is only possible through expertise and experience. This thesis proposes a robotic system that creates a full 3D model of the environment with color and thermal information by combining thermal imaging with the technology of terrestrial laser scanning. The addition of a color camera facilitates the interpretation of the data and allows for other application areas. The data from all sensors collected at different positions is joined in one common reference frame using calibration and scan matching. The first part of the thesis deals with 3D point cloud processing with the emphasis on accessing point cloud data efficiently, detecting planar structures in the data and registering multiple point clouds into one common coordinate system. The second part covers the autonomous exploration and data acquisition with a mobile robot with the objective to minimize the unseen area in 3D space. Furthermore, the combination of different modalities, color images, thermal images and point cloud data through calibration is elaborated. The last part presents applications for the the collected data. Among these are methods to detect the structure of building interiors for reconstruction purposes and subsequent detection and classification of windows. A system to project the gathered thermal information back into the scene is presented as well as methods to improve the color information and to join separately acquired point clouds and photo series. A full multi-modal 3D model contains all the relevant geometric information about the recorded scene and enables an expert to fully analyze it off-site. The technology clears the path for automatically detecting points of interest thereby helping the expert to analyze the heat flow as well as localize and identify heat leaks. The concept is modular and neither limited to achieving energy efficiency nor restricted to the use in combination with a mobile platform. It also finds its application in fields such as archaeology and geology and can be extended by further sensors. N2 - Man stelle sich eine Technologie vor, die automatisch ein vollständiges 3D-Thermographiemodell einer Umgebung generiert und Temperaturspitzen darin erkennt. Zur besseren Orientierung innerhalb des Modells ist dieses mit Farbinformationen erweitert. In der Analyse temperaturrelevanter Fragestellungen sind Thermalbilder der Stand der Technik. Darunter fallen Energieeffizienz und die Sicherung wichtiger Infrastruktur, wie Energieversorgung und Systeme zur Temperaturregulierung. Die Überwachung und anschließende Analyse der Daten eines großen Gebäudes ist aufwändig, da über mehrere Stunden stabile Bedingungen garantiert und detaillierte Aufzeichnungen über die Aufnahmeposen und die Umgebungsverhältnisse für jedes Wärmebild erstellt werden müssen. Einige Anwendungen erfordern wiederholte Messungen, um Veränderungen über die Zeit zu beobachten. Eine Analyse der Szene ist nur mit Erfahrung und Expertise möglich. Diese Arbeit stellt ein Robotersystem vor, das durch Kombination von Thermographie mit terrestrischem Laserscanning ein vollständiges 3D Modell der Umgebung mit Farb- und Temperaturinformationen erstellt. Die ergänzende Farbkamera vereinfacht die Interpretation der Daten und eröffnet weitere Anwendungsfelder. Die an unterschiedlichen Positionen aufgenommenen Daten aller Sensoren werden durch Kalibrierung und Scanmatching in einem gemeinsamen Bezugssystem zusammengefügt. Der erste Teil der Arbeit behandelt 3D-Punktwolkenverarbeitung mit Schwerpunkt auf effizientem Punktzugriff, Erkennung planarer Strukturen und Registrierung mehrerer Punktwolken in einem gemeinsamen Koordinatensystem. Der zweite Teil beschreibt die autonome Erkundung und Datenakquise mit einem mobilen Roboter, mit dem Ziel, die bisher nicht erfassten Bereiche im 3D-Raum zu minimieren. Des Weiteren wird die Kombination verschiedener Modalitäten, Farbbilder, Thermalbilder und Punktwolken durch Kalibrierung ausgearbeitet. Den abschließenden Teil stellen Anwendungsszenarien für die gesammelten Daten dar, darunter Methoden zur Erkennung der Innenraumstruktur für die Rekonstruktion von Gebäuden und der anschließenden Erkennung und Klassifizierung von Fenstern. Ein System zur Rückprojektion der gesammelten Thermalinformation in die Umgebung wird ebenso vorgestellt wie Methoden zur Verbesserung der Farbinformationen und zum Zusammenfügen separat aufgenommener Punktwolken und Fotoreihen. Ein vollständiges multi-modales 3D Modell enthält alle relevanten geometrischen Informationen der aufgenommenen Szene und ermöglicht einem Experten, diese standortunabhängig zu analysieren. Diese Technologie ebnet den Weg für die automatische Erkennung relevanter Bereiche und für die Analyse des Wärmeflusses und vereinfacht somit die Lokalisierung und Identifikation von Wärmelecks für den Experten. Das vorgestellte modulare Konzept ist weder auf den Anwendungsfall Energieeffizienz beschränkt noch auf die Verwendung einer mobilen Plattform angewiesen. Es ist beispielsweise auch in Feldern wie der Archäologie und Geologie einsetzbar und kann durch zusätzliche Sensoren erweitert werden. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 14 KW - Punktwolke KW - Lidar KW - Thermografie KW - Robotik KW - 3D point cloud KW - Laser scanning KW - Robotics KW - 3D thermal mapping KW - Registration Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-157085 SN - 978-3-945459-20-1 SN - 1868-7474 SN - 1868-7466 ER - TY - JOUR A1 - Breves, Priska A1 - Dodel, Nicola T1 - The influence of cybersickness and the media devices’ mobility on the persuasive effects of 360° commercials JF - Multimedia Tools and Applications N2 - With the rise of immersive media, advertisers have started to use 360° commercials to engage and persuade consumers. Two experiments were conducted to address research gaps and to validate the positive impact of 360° commercials in realistic settings. The first study (N = 62) compared the effects of 360° commercials using either a mobile cardboard head-mounted display (HMD) or a laptop. This experiment was conducted in the participants’ living rooms and incorporated individual feelings of cybersickness as a moderator. The participants who experienced the 360° commercial with the HMD reported higher spatial presence and product evaluation, but their purchase intentions were only increased when their reported cybersickness was low. The second experiment (N = 197) was conducted online and analyzed the impact of 360° commercials that were experienced with mobile (smartphone/tablet) or static (laptop/desktop) devices instead of HMDs. The positive effects of omnidirectional videos were stronger when participants used mobile devices. KW - virtual reality KW - immersive advertising KW - spatial presence KW - cybersickness KW - advertising effectiveness Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-269194 SN - 1573-7721 VL - 80 IS - 18 ER -