TY - THES A1 - Klein, Alexander T1 - Performance Issues of MAC and Routing Protocols in Wireless Sensor Networks T1 - Leistungsbeschränkende Faktoren von MAC und Routingprotokollen in drahtlosen Sensornetzen N2 - The focus of this work lies on the communication issues of Medium Access Control (MAC) and routing protocols in the context of WSNs. The communication challenges in these networks mainly result from high node density, low bandwidth, low energy constraints and the hardware limitations in terms of memory, computational power and sensing capabilities of low-power transceivers. For this reason, the structure of WSNs is always kept as simple as possible to minimize the impact of communication issues. Thus, the majority of WSNs apply a simple one hop star topology since multi-hop communication has high demands on the routing protocol since it increases the bandwidth requirements of the network. Moreover, medium access becomes a challenging problem due to the fact that low-power transceivers are very limited in their sensing capabilities. The first contribution is represented by the Backoff Preamble-based MAC Protocol with Sequential Contention Resolution (BPS-MAC) which is designed to overcome the limitations of low-power transceivers. Two communication issues, namely the Clear Channel Assessment (CCA) delay and the turnaround time, are directly addressed by the protocol. The CCA delay represents the period of time which is required by the transceiver to detect a busy radio channel while the turnaround time specifies the period of time which is required to switch between receive and transmit mode. Standard Carrier Sense Multiple Access (CSMA) protocols do not achieve high performance in terms of packet loss if the traffic is highly correlated due to the fact that the transceiver is not able to sense the medium during the switching phase. Therefore, a node may start to transmit data while another node is already transmitting since it has sensed an idle medium right before it started to switch its transceiver from receive to transmit mode. The BPS-MAC protocol uses a new sequential preamble-based medium access strategy which can be adapted to the hardware capabilities of the transceivers. The protocol achieves a very low packet loss rate even in wireless networks with high node density and event-driven traffic without the need of synchronization. This makes the protocol attractive to applications such as structural health monitoring, where event suppression is not an option. Moreover, acknowledgments or complex retransmission strategies become almost unnecessary since the sequential preamble-based contention resolution mechanism minimizes the collision probability. However, packets can still be lost as a consequence of interference or other issues which affect signal propagation. The second contribution consists of a new routing protocol which is able to quickly detect topology changes without generating a large amount of overhead. The key characteristics of the Statistic-Based Routing (SBR) protocol are high end-to-end reliability (in fixed and mobile networks), load balancing capabilities, a smooth continuous routing metric, quick adaptation to changing network conditions, low processing and memory requirements, low overhead, support of unidirectional links and simplicity. The protocol can establish routes in a hybrid or a proactive mode and uses an adaptive continuous routing metric which makes it very flexible in terms of scalability while maintaining stable routes. The hybrid mode is optimized for low-power WSNs since routes are only established on demand. The difference of the hybrid mode to reactive routing strategies is that routing messages are periodically transmitted to maintain already established routes. However, the protocol stops the transmission of routing messages if no data packets are transmitted for a certain time period in order to minimize the routing overhead and the energy consumption. The proactive mode is designed for high data rate networks which have less energy constraints. In this mode, the protocol periodically transmits routing messages to establish routes in a proactive way even in the absence of data traffic. Thus, nodes in the network can immediately transmit data since the route to the destination is already established in advance. In addition, a new delay-based routing message forwarding strategy is introduced. The forwarding strategy is part of SBR but can also be applied to many routing protocols in order to modify the established topology. The strategy can be used, e.g. in mobile networks, to decrease the packet loss by deferring routing messages with respect to the neighbor change rate. Thus, nodes with a stable neighborhood forward messages faster than nodes within a fast changing neighborhood. As a result, routes are established through nodes with correlated movement which results in fewer topology changes due to higher link durations. N2 - Im Rahmen dieser Arbeit werden leistungsbeschränkende Faktoren von Medium Access Control (MAC) und Routingprotokollen im Kontext von drahtlosen Sensornetzen untersucht. Zunächst werden typische Probleme des Funkkanals diskutiert. Anschließend führen eine Einteilung von MAC Protokollen, sowie eine Gegenüberstellung relevanter Protokolle in die Thematik ein. Daraufhin werden hardwarelimitierende Faktoren und deren Auswirkung auf die Effizienz von Kanalzugriffsprotokollen untersucht. Des Weiteren wird das vom Autor entwickelte Backoff Preamble-based MAC Protokoll (BPS-MAC) vorgestellt, welches auf die limitierten Fähigkeiten sensortypischer Hardware eingeht und für dichte Sensornetze mit korreliertem Datenverkehr optimiert ist. Ein weiterer Schwerpunkt dieser Arbeit stellt das Thema Routing dar. Hier wird ebenfalls mit einer Einteilung der Protokolle in die Thematik eingeführt. Darüber hinaus werden die wichtigsten Aufgaben von Routingprotokollen vorgestellt. Ein Überblick über häufig verwendete Routingmetriken und Routingprotokolle schließen die Einführung in diesen Themenkomplex ab. Abschließend wird das im Rahmen der Dissertation entwickelte Statistic-Based-Routing (SBR) Protokoll vorgestellt, welches ebenfalls für drahtlose Sensornetze optimiert ist. Der letzte Schwerpunkt beschreibt die Problematik der Leistungsbewertung von Routingprotokollen hinsichtlich klassischer Leistungsparameter wie Paketverlust und Verzögerung. Ebenfalls werden weitere Leistungsparameter wie zum Beispiel die vom Nutzer wahrgenommene Netzqualität genauer untersucht. T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 03/10 KW - Routing KW - Drahtloses Sensorsystem KW - Leistungsbewertung KW - Diskrete Simulation KW - MAC KW - Kanalzugriff KW - Medium KW - MAC KW - routing KW - sensor KW - networks KW - simulation Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-52870 ER - TY - THES A1 - Zinner, Thomas T1 - Performance Modeling of QoE-Aware Multipath Video Transmission in the Future Internet T1 - Leistungsmodellierung einer Mehrpfad Video Übertragung im zukünftigen Internet unter Berücksichtigung der QoE N2 - Internet applications are becoming more and more flexible to support diverge user demands and network conditions. This is reflected by technical concepts, which provide new adaptation mechanisms to allow fine grained adjustment of the application quality and the corresponding bandwidth requirements. For the case of video streaming, the scalable video codec H.264/SVC allows the flexible adaptation of frame rate, video resolution and image quality with respect to the available network resources. In order to guarantee a good user-perceived quality (Quality of Experience, QoE) it is necessary to adjust and optimize the video quality accurately. But not only have the applications of the current Internet changed. Within network and transport, new technologies evolved during the last years providing a more flexible and efficient usage of data transport and network resources. One of the most promising technologies is Network Virtualization (NV) which is seen as an enabler to overcome the ossification of the Internet stack. It provides means to simultaneously operate multiple logical networks which allow for example application-specific addressing, naming and routing, or their individual resource management. New transport mechanisms like multipath transmission on the network and transport layer aim at an efficient usage of available transport resources. However, the simultaneous transmission of data via heterogeneous transport paths and communication technologies inevitably introduces packet reordering. Additional mechanisms and buffers are required to restore the correct packet order and thus to prevent a disturbance of the data transport. A proper buffer dimensioning as well as the classification of the impact of varying path characteristics like bandwidth and delay require appropriate evaluation methods. Additionally, for a path selection mechanism real time evaluation mechanisms are needed. A better application-network interaction and the corresponding exchange of information enable an efficient adaptation of the application to the network conditions and vice versa. This PhD thesis analyzes a video streaming architecture utilizing multipath transmission and scalable video coding and develops the following optimization possibilities and results: Analysis and dimensioning methods for multipath transmission, quantification of the adaptation possibilities to the current network conditions with respect to the QoE for H.264/SVC, and evaluation and optimization of a future video streaming architecture, which allows a better interaction of application and network. N2 - Die Applikationen im Internet passen sich immer besser an unterschiedliche Anforderungen der Nutzer und variierende Netzwerkbedingungen an. Neue Mechanismen ermöglichen die zielgerichtete Anpassung der Anwendungsqualität und damit der benötigten Bandbreite. Im Falle von Videostreaming ermöglicht der skalierbare Videocodec H.264/SVC, die flexible Veränderung der Bildwiederholungsrate, der Auflösung des Videos und der Bildqualität an die vorhandenen Ressourcen im Netzwerk. Um eine gute vom Nutzer erfahrene Dienstgüte (Quality of Experience, QoE) zu garantieren, muss die Videoqualität richtig angepasst und optimiert werden. Aber nicht nur die Anwendungen des heutigen Internets haben sich verändert. Gerade in den letzten Jahren entstanden neue Netzwerk- und Transporttechnologien, welche eine flexiblere und effizientere Nutzung der Kommunikationsnetze erlauben. Eine dieser Techniken ist die Virtualisierung von Netzwerken. Sie erlaubt es auf einem gemeinsamen physikalischen Netz verschiedene logische Netze zu betreiben, die zum Beispiel Anwendungs-abhängige Adressierung unterstützen, eigene Namensgebung erlauben oder ein individuelles Ressourcen Management ermöglichen. Neuartige Transportmechanismen wie Mehrpfadübertragung auf Netzwerk- und Transportebene des ISO/OSI Stacks streben eine effiziente Ausnutzung der zur Verfügung stehenden Übertragungsmöglichkeiten an. Doch die simultane Übertragung von Daten über heterogene Kommunikationspfade und –technologien führt unausweichlich zu einer Veränderung der Reihenfolge, in der die Pakete ankommen. Es werden zusätzliche Mechanismen und Puffer benötigt, um die ursprüngliche Paketreihenfolge wieder herzustellen und so einen störenden Einfluss auf den Datentransport zu verhindern. Die richtige Dimensionierung dieser Puffer sowie die Klassifizierung des Einflusses von variierenden Pfadparametern wie Bandbreite und Verzögerungen setzen passende Evaluierungsmethoden voraus. Darüber hinaus werden für die Auswahl von geeigneten Pfaden aus einer Menge vorhandener Pfade echtzeitfähige Bewertungsmechanismen benötigt. Eine bessere Interaktion zwischen Applikationen und Netzwerk und der damit verbundene Informationsaustausch ermöglicht die effiziente Anpassung der Applikationsqualität an das Netzwerk und umgekehrt. Diese Doktorarbeit analysiert eine auf Mehrpfadübertragung und skalierbarer Videokodierung basierende Videostreaming Architektur und erarbeitet die folgenden Optimierungsmöglichkeiten und Auswertungen: Analyse- und Dimensionierungsmethoden für Mehrpfadübertragung, Quantifizierung der Anpassungsmöglichkeiten von SVC an das Netzwerk unter Berücksichtigung der QoE und Evaluierung und Optimierung einer zukünftigen Videostreaming Architektur, welche eine stärkere Interaktion zwischen Applikation und Netzwerk ermöglicht. T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 03/12 KW - Videoübertragung KW - H.264 SVC KW - Modellierung KW - Quality-of-Experience KW - Mehrpfadübertragung KW - Multipath Transmission KW - Video Streaming KW - H.264/SVC KW - QoE KW - Performance Modeling Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-72324 ER - TY - THES A1 - Mäder, Andreas T1 - Performance Models for UMTS 3.5G Mobile Wireless Systems T1 - Leistungsmodelle für UMTS 3.5G Mobilfunksysteme N2 - Mobile telecommunication systems of the 3.5th generation (3.5G) constitute a first step towards the requirements of an all-IP world. As the denotation suggests, 3.5G systems are not completely new designed from scratch. Instead, they are evolved from existing 3G systems like UMTS or cdma2000. 3.5G systems are primarily designed and optimized for packet-switched best-effort traffic, but they are also intended to increase system capacity by exploiting available radio resources more efficiently. Systems based on cdma2000 are enhanced with 1xEV-DO (EV-DO: evolution, data-optimized). In the UMTS domain, the 3G partnership project (3GPP) specified the High Speed Packet Access (HSPA) family, consisting of High Speed Downlink Packet Access (HSDPA) and its counterpart High Speed Uplink Packet Access (HSUPA) or Enhanced Uplink. The focus of this monograph is on HSPA systems, although the operation principles of other 3.5G systems are similar. One of the main contributions of our work are performance models which allow a holistic view on the system. The models consider user traffic on flow-level, such that only on significant changes of the system state a recalculation of parameters like bandwidth is necessary. The impact of lower layers is captured by stochastic models. This approach combines accurate modeling and the ability to cope with computational complexity. Adopting this approach to HSDPA, we develop a new physical layer abstraction model that takes radio resources, scheduling discipline, radio propagation and mobile device capabilities into account. Together with models for the calculation of network-wide interference and transmit powers, a discrete-event simulation and an analytical model based on a queuing-theoretical approach are proposed. For the Enhanced Uplink, we develop analytical models considering independent and correlated other-cell interference. N2 - Die vorliegende Arbeit beschäftigt sich mit Mobilfunksystemen der Generation 3.5 im Allgemeinen, und mit den UMTS-spezifischen Ausprägungen HSDPA (High Speed Downlink Packet Access) und HSUPA (High Speed Uplink Packet Access) bzw. Enhanced Uplink im speziellen. Es werden integrierte Systeme betrachtet, d.h. 3.5G Datenkanäle koexistieren mit "klassischen" UMTS Datenkanälen wie in den Spezifikationen von UMTS Release ´99 beschrieben. T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 02/08 KW - Mobilfunk KW - Leistungsbewertung KW - UMTS KW - HSPA KW - Funkressourcenverwaltung KW - Modellierungstechniken KW - Netzwerkplanung KW - UMTS KW - HSPA KW - radio resource management KW - modeling techniques KW - network planning Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-32525 ER - TY - THES A1 - Pries, Jan Rastin T1 - Performance Optimization of Wireless Infrastructure and Mesh Networks T1 - Leistungsoptimierung von drahtlosen Infrastruktur und Mesh Netzen N2 - Future broadband wireless networks should be able to support not only best effort traffic but also real-time traffic with strict Quality of Service (QoS) constraints. In addition, their available resources are scare and limit the number of users. To facilitate QoS guarantees and increase the maximum number of concurrent users, wireless networks require careful planning and optimization. In this monograph, we studied three aspects of performance optimization in wireless networks: resource optimization in WLAN infrastructure networks, quality of experience control in wireless mesh networks, and planning and optimization of wireless mesh networks. An adaptive resource management system is required to effectively utilize the limited resources on the air interface and to guarantee QoS for real-time applications. Thereby, both WLAN infrastructure and WLAN mesh networks have to be considered. An a-priori setting of the access parameters is not meaningful due to the contention-based medium access and the high dynamics of the system. Thus, a management system is required which dynamically adjusts the channel access parameters based on the network load. While this is sufficient for wireless infrastructure networks, interferences on neighboring paths and self-interferences have to be considered for wireless mesh networks. In addition, a careful channel allocation and route assignment is needed. Due to the large parameter space, standard optimization techniques fail for optimizing large wireless mesh networks. In this monograph, we reveal that biology-inspired optimization techniques, namely genetic algorithms, are well-suitable for the planning and optimization of wireless mesh networks. Although genetic algorithms generally do not always find the optimal solution, we show that with a good parameter set for the genetic algorithm, the overall throughput of the wireless mesh network can be significantly improved while still sharing the resources fairly among the users. N2 - Die Anbindung an das Internet erfolgt zunehmend über drahtlose Netze. Deren Ressourcen sind allerdings limitiert, was die Anzahl der unterstützten Nutzer stark einschränkt. Zudem ist ein Trend dieser Nutzer weg von der Verwendung reiner Datendienste zu Diensten mit Echtzeitanforderungen wie Voice over IP (VoIP) zu erkennen, deren Dienstgüteanforderungen eingehalten werden müssen. Heutige drahtlose Zugangsnetze sind jedoch nur für den herkömmlichen Datenverkehr ausgelegt. Der IEEE 802.11 WLAN Standard unterscheidet zwar zwischen verschiedenen Dienstklassen, gibt aber keine Dienstgütegarantien. Um die Dienstgüte (Quality of Service, QoS), bzw. die vom Nutzer erfahrene Dienstgüte (Quality of Experience, QoE) zu garantieren, müssen die zukünftigen drahtlosen Netze daher sorgfältig geplant und optimiert werden. Um die limitierten Ressourcen auf der Luftschnittstelle effektiv zu nutzen und um Dienstgüteanforderungen für Echtzeitanwendungen einzuhalten, bedarf es eines adaptiven Ressourcenmanagements. Dabei sind sowohl drahtlose Infrastruktur, als auch drahtlose Mesh-Netze zu betrachten. Durch den randomisierten Medienzugriff und die hohe Dynamik im System ist eine a-priori Wahl der Zugangsparameter nicht sinnvoll. Vielmehr wird ein Managementsystem benötigt, das die Zugangsparameter dynamisch in Abhängigkeit der Last in einem Netz wählt. Während dies für drahtlose Infrastrukturnetze ausreicht, müssen in drahtlosen Mesh-Netzen zusätzlich noch Interferenzen von Nachbarpfaden und Eigeninterferenzen berücksichtigt werden. Desweiteren ist eine sorgfältige Planung der Kanalzuweisung und des Routings notwendig, um einerseits den Durchsatz in drahtlosen Mesh-Netzen zu maximieren und andererseits die Ressourcen fair zwischen den Stationen aufzuteilen. Da es dabei eine Vielzahl von Parametern zu berücksichtigen gilt, sind neue Optimierungsmethoden notwendig, die es ermöglichen, auch große Mesh-Netze in annehmbarer Zeit zu planen und zu optimieren. Diese Doktorarbeit arbeitet die folgenden drei Optimierungsmöglichkeiten für drahtlose Zugangsnetze aus: Optimierung der Zugangsparameter in drahtlosen Infrastrukturnetzen, Optimierung von drahtlosen Mesh-Netzen unter Berücksichtigung der QoE und Planung und Optimierung von drahtlosen Mesh-Netzen mit Berücksichtigung einer fairen Ressourcenallokation. Die Ergebnisse und Untersuchungen dieser Arbeit gliedern sich entsprechend dieser Optimierungsmöglichkeiten. T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 01/10 KW - IEEE 802.11 KW - Leistungsbewertung KW - Optimierung KW - Dienstgüte KW - Netzplanung KW - Drahtloses lokales Netz KW - WLAN KW - Mesh Netze KW - Genetische Optimierung KW - WLAN KW - Optimization KW - Mesh Networks KW - Genetic Optimization Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-46097 ER - TY - THES A1 - Schlosser, Daniel T1 - Quality of Experience Management in Virtual Future Networks T1 - Netzwerkmanagement unter Berücksichtigung der vom Benutzer erfahrenen Dienstgüte in virtuellen zukünftigen Netzen N2 - Aktuell beobachten wir eine drastische Vervielfältigung der Dienste und Anwendungen, die das Internet für den Datentransport nutzen. Dabei unterscheiden sich die Anforderungen dieser Dienste an das Netzwerk deutlich. Das Netzwerkmanagement wird durch diese Diversität der nutzenden Dienste aber deutlich erschwert, da es einem Datentransportdienstleister kaum möglich ist, die unterschiedlichen Verbindungen zu unterscheiden, ohne den Inhalt der transportierten Daten zu analysieren. Netzwerkvirtualisierung ist eine vielversprechende Lösung für dieses Problem, da sie es ermöglicht für verschiedene Dienste unterschiedliche virtuelle Netze auf dem gleichen physikalischen Substrat zu betreiben. Diese Diensttrennung ermöglicht es, jedes einzelne Netz anwendungsspezifisch zu steuern. Ziel einer solchen Netzsteuerung ist es, sowohl die vom Nutzer erfahrene Dienstgüte als auch die Kosteneffizienz des Datentransports zu optimieren. Darüber hinaus wird es mit Netzwerkvirtualisierung möglich das physikalische Netz so weit zu abstrahieren, dass die aktuell fest verzahnten Rollen von Netzwerkbesitzer und Netzwerkbetreiber entkoppelt werden können. Darüber hinaus stellt Netzwerkvirtualisierung sicher, dass unterschiedliche Datennetze, die gleichzeitig auf dem gleichen physikalischen Netz betrieben werden, sich gegenseitig weder beeinflussen noch stören können. Diese Arbeit  beschäftigt sich mit ausgewählten Aspekten dieses Themenkomplexes und fokussiert sich darauf, ein virtuelles Netzwerk mit bestmöglicher Dienstqualität für den Nutzer zu betreiben und zu steuern. Dafür wird ein Top-down-Ansatz gewählt, der von den Anwendungsfällen, einer möglichen Netzwerkvirtualisierungs-Architektur und aktuellen Möglichkeiten der Hardwarevirtualisierung ausgeht. Im Weiteren fokussiert sich die Arbeit dann in Richtung Bestimmung und Optimierung der vom Nutzer erfahrenen Dienstqualität (QoE) auf Applikationsschicht und diskutiert Möglichkeiten zur Messung und Überwachung von wesentlichen Netzparametern in virtualisierten Netzen. N2 - Currently, we observe a strong growth of services and applications, which use the Internet for data transport. However, the network requirements of these applications differ significantly. This makes network management difficult, since it complicated to separate network flows into application classes without inspecting application layer data. Network virtualization is a promising solution to this problem. It enables running different virtual network on the same physical substrate. Separating networks based on the service supported within allows controlling each network according to the specific needs of the application. The aim of such a network control is to optimize the user perceived quality as well as the cost efficiency of the data transport. Furthermore, network virtualization abstracts the network functionality from the underlying implementation and facilitates the split of the currently tightly integrated roles of Internet Service Provider and network owner. Additionally, network virtualization guarantees that different virtual networks run on the same physical substrate do not interfere with each other. This thesis discusses different aspects of the network virtualization topic. It is focused on how to manage and control a virtual network to guarantee the best Quality of Experience for the user. Therefore, a top-down approach is chosen. Starting with use cases of virtual networks, a possible architecture is derived and current implementation options based on hardware virtualization are explored. In the following, this thesis focuses on assessing the Quality of Experience perceived by the user and how it can be optimized on application layer. Furthermore, options for measuring and monitoring significant network parameters of virtual networks are considered. T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 01/12 KW - Netzwerkmanagement KW - Dienstgüte KW - Netzwerkvirtualisierung KW - QoS KW - QoE KW - Network Virtualization KW - Quality of Experience KW - Network Management KW - Quality of Service Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-69986 ER - TY - THES A1 - Martin, Rüdiger T1 - Resilience, Provisioning, and Control for the Network of the Future T1 - Ausfallsicherheit, Dimensionierungsansätze und Kontrollmechanismen für das Netz der Zukunft N2 - The Internet sees an ongoing transformation process from a single best-effort service network into a multi-service network. In addition to traditional applications like e-mail,WWW-traffic, or file transfer, future generation networks (FGNs) will carry services with real-time constraints and stringent availability and reliability requirements like Voice over IP (VoIP), video conferencing, virtual private networks (VPNs) for finance, other real-time business applications, tele-medicine, or tele-robotics. Hence, quality of service (QoS) guarantees and resilience to failures are crucial characteristics of an FGN architecture. At the same time, network operations must be efficient. This necessitates sophisticated mechanisms for the provisioning and the control of future communication infrastructures. In this work we investigate such echanisms for resilient FGNs. There are many aspects of the provisioning and control of resilient FGNs such as traffic matrix estimation, traffic characterization, traffic forecasting, mechanisms for QoS enforcement also during failure cases, resilient routing, or calability concerns for future routing and addressing mechanisms. In this work we focus on three important aspects for which performance analysis can deliver substantial insights: load balancing for multipath Internet routing, fast resilience concepts, and advanced dimensioning techniques for resilient networks. Routing in modern communication networks is often based on multipath structures, e.g., equal-cost multipath routing (ECMP) in IP networks, to facilitate traffic engineering and resiliency. When multipath routing is applied, load balancing algorithms distribute the traffic over available paths towards the destination according to pre-configured distribution values. State-of-the-art load balancing algorithms operate either on the packet or the flow level. Packet level mechanisms achieve highly accurate traffic distributions, but are known to have negative effects on the performance of transport protocols and should not be applied. Flow level mechanisms avoid performance degradations, but at the expense of reduced accuracy. These inaccuracies may have unpredictable effects on link capacity requirements and complicate resource management. Thus, it is important to exactly understand the accuracy and dynamics of load balancing algorithms in order to be able to exercise better network control. Knowing about their weaknesses, it is also important to look for alternatives and to assess their applicability in different networking scenarios. This is the first aspect of this work. Component failures are inevitable during the operation of communication networks and lead to routing disruptions if no special precautions are taken. In case of a failure, the robust shortest-path routing of the Internet reconverges after some time to a state where all nodes are again reachable – provided physical connectivity still exists. But stringent availability and reliability criteria of new services make a fast reaction to failures obligatory for resilient FGNs. This led to the development of fast reroute (FRR) concepts for MPLS and IP routing. The operations of MPLS-FRR have already been standardized. Still, the standards leave some degrees of freedom for the resilient path layout and it is important to understand the tradeoffs between different options for the path layout to efficiently provision resilient FGNs. In contrast, the standardization for IP-FRR is an ongoing process. The applicability and possible combinations of different concepts still are open issues. IP-FRR also facilitates a comprehensive resilience framework for IP routing covering all steps of the failure recovery cycle. These points constitute another aspect of this work. Finally, communication networks are usually over-provisioned, i.e., they have much more capacity installed than actually required during normal operation. This is a precaution for various challenges such as network element failures. An alternative to this capacity overprovisioning (CO) approach is admission control (AC). AC blocks new flows in case of imminent overload due to unanticipated events to protect the QoS for already admitted flows. On the one hand, CO is generally viewed as a simple mechanism, AC as a more complex mechanism that complicates the network control plane and raises interoperability issues. On the other hand, AC appears more cost-efficient than CO. To obtain advanced provisioning methods for resilient FGNs, it is important to find suitable models for irregular events, such as failures and different sources of overload, and to incorporate them into capacity dimensioning methods. This allows for a fair comparison between CO and AC in various situations and yields a better understanding of the strengths and weaknesses of both concepts. Such an advanced capacity dimensioning method for resilient FGNs represents the third aspect of this work. N2 - Das Internet befindet sich gegenwärtig in einem Transformationsprozess von einem Netz mit einer einzigen best-effort Dienstklasse hin zu einem Mehr-Dienste-Netz. Zusätzlich zu herkömmlichen Anwendungen wie E-Mail, WWW oder Datenübertragung werden zukünftige Netze Dienste mit Echtzeitbedürfnissen und strikten Anforderungen an Verfügbarkeit und Zuverlässigkeit wie Voice over IP (VoIP), Videokonferenzdienste, Virtual Private Networks (VPNs) für Finanzanwendungen und andere Geschäftsanwendungen mit Echtzeitanforderungen, Tele-Medizin oder Telerobotik tragen. Daher sind die Gewährleistung von Dienstgüte und Ausfallsicherheit wesentliche Merkmale zukünftiger Netzarchitekturen. Gleichzeitig muss der Netzbetrieb effizient sein. Dies zieht den Bedarf an ausgefeilten Mechanismen für die Dimensionierung und Kontrolle ausfallsicherer Kommunikationsstrukturen nach sich. In dieser Arbeit werden solche Mechanismen, nämlich Lastaufteilung, Konzepte zur schnellen Reaktion im Fehlerfall und intelligente Ansätze zur Netzdimensionierung, untersucht. T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 03/08 KW - Backbone-Netz KW - load balancing KW - resilience KW - fast reroute KW - admission control KW - overprovisioning Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-28497 ER - TY - THES A1 - Herrmann, Christian T1 - Robotic Motion Compensation for Applications in Radiation Oncology T1 - Robotergestützte Bewegungskompensation für Anwendungen in der Radioonkologie N2 - Aufgrund vieler Verbesserungen der Behandlungsmethoden im Laufe der letzten 60 Jahre, erlaubt die Strahlentherapie heutzutage präzise Behandlungen von statischen Tumoren. Jedoch birgt die Bestrahlung von sich bewegenden Tumoren noch große Herausforderungen in sich, da bewegliche Tumore oft den Behandlungsstrahl verlassen. Dabei reduziert sich die Strahlendosis im Tumor während sich diese im umliegenden gesunden Gewebe erhöht. Diese Forschungsarbeit zielt darauf ab, die Grenzen der Strahlentherapie zu erweitern, um präzise Behandlungen von beweglichen Tumoren zu ermöglichen. Der Fokus der Arbeit liegt auf der Erstellung eines Echtzeitsystems zur aktiven Kompensation von Tumorbewegungen durch robotergestützte Methoden. Während Behandlungen befinden sich Patienten auf einer Patientenliege, mit der statische Lagerungsfehler vor Beginn einer Behandlung korrigiert werden. Die in dieser Arbeit verwendete Patientenliege "HexaPOD" ist ein paralleler Manipulator mit sechs Freiheitsgraden, der große Lasten innerhalb eines eingeschränkten Arbeitsbereichs präzise positionieren kann. Obwohl der HexaPOD ursprünglich nicht für dynamische Anwendungen konzipiert wurde, wird dieser für eine dauerhafte Bewegungskompensation eingesetzt, in dem Patienten so bewegt werden, dass Tumore präzise im Zentralstrahl während der Dauer einer gesamten Behandlung verbleiben. Um ein echtzeitfähiges Kompensationssystem auf Basis des HexaPODs zu realisieren, muss eine Reihe an Herausforderungen bewältigt werden. Echtzeitaspekte werden einerseits durch die Verwendung eines harten Echtzeitbetriebssystems abgedeckt, andererseits durch die Messung und Schätzung von Latenzzeiten aller physikalischen Größen im System, z.B. Messungen der Tumor- und Atemposition. Neben der konsistenten und durchgängigen Berücksichtigung von akkuraten Zeitinformation, werden alle software-induzierten Latenzen adaptiv ausgeglichen. Dies erfordert Vorhersagen der Tumorposition in die nahe Zukunft. Zahlreiche Prädiktoren zur Atem- und Tumorpositionsvorhersage werden vorgeschlagen und anhand verschiedenster Metriken evaluiert. Erweiterungen der Prädiktionsalgorithmen werden eingeführt, die sowohl Atem- als auch Tumorpositionsinformationen fusionieren, um Vorhersagen ohne explizites Korrelationsmodell zu ermöglichen. Die Vorhersagen bestimmen den zukünftigen Bewegungspfad des HexaPODs, um Tumorbewegungen zu kompensieren. Dazu werden verschiedene Regler entwickelt, die eine Trajektorienverfolgung mit dem HexaPOD ermöglichen. Auf der Basis von linearer und nicht-linearer dynamischer Modellierung des HexaPODs mit Methoden der Systemidentifikation, wird zunächst ein modellprädiktiver Regler entwickelt. Ein zweiter Regler wird auf Basis einer Annahme über das Arbeitsprinzip des internen Reglers im HexaPOD entworfen. Schließlich wird ein dritter Regler vorgeschlagen, der beide vorhergehenden Regler miteinander kombiniert. Für jeden dieser Regler werden vergleichende Ergebnisse aus Experimenten mit realer Hardware und menschlichen Versuchspersonen präsentiert und diskutiert. Darüber hinaus wird die geeignete Wahl von freien Parametern in den Reglern vorgestellt. Neben einer präzisen Verfolgung der Referenztrajektorie spielt der Patientenkomfort eine entscheidende Rolle für die Akzeptanz des Systems. Es wird gezeigt, dass die Regler glatte Trajektorien realisieren können, um zu garantieren, dass sich Patienten wohl fühlen während ihre Tumorbewegung mit Genauigkeiten im Submillimeterbereich ausgeglichen wird. Gesamtfehler werden im Kompensationssystem analysiert, in dem diese zu Trajektorienverfolgungsfehlern und Prädiktionsfehlern in Beziehung gesetzt werden. Durch Ausnutzung von Eigenschaften verschiedener Prädiktoren wird gezeigt, dass die Startzeit des Systems bis die Verfolgung der Referenztrajektorie erreicht ist, wenige Sekunden beträgt. Dies gilt insbesondere für den Fall eines initial ruhenden HexaPODs und ohne Vorwissen über Tumorbewegungen. Dies zeigt die Eignung des Systems für die sehr kurz fraktionierten Behandlungen von Lungentumoren. Das Tumorkompensationssystem wurde ausschließlich auf Basis von klinischer Standard-Hardware entwickelt, die in vielen Behandlungsräumen zu finden ist. Durch ein einfaches und flexibles Design können Behandlungsräume in kosteneffizienter Weise um Möglichkeiten der Bewegungskompensation ergänzt werden. Darüber hinaus werden aktuelle Behandlungsmethoden wie intensitätsmodulierte Strahlentherapie oder Volumetric Modulated Arc Therapy in keiner Weise eingeschränkt. Aufgrund der Unterstützung verschiedener Kompensationsmodi kann das System auf alle beweglichen Tumore angewendet werden, unabhängig davon ob die Bewegungen vorhersagbar (Lungentumore) oder nicht vorhersagbar (Prostatatumore) sind. Durch Integration von geeigneten Methoden zur Tumorpositionsbestimmung kann das System auf einfache Weise zur Kompensation von anderen Tumoren erweitert werden. N2 - Radiation therapy today, on account of improvements in treatment procedures over the last 60 years, allows precise treatment of static tumors inside the human body. However, irradiation of moving tumors is still a challenging task as moving tumors often leave the treatment beam and the radiation dose delivered to the tumor reduces simultaneously increasing that on healthy tissue. This research work aims to push the frontiers of radiation therapy in order to enable precise treatment of moving tumors with focus on research and development of a unique real-time system enabling active motion compensation through robotic means to compensate tumor motion. During treatment, patients lie on a treatment couch which is normally used for static position corrections of patient set-up errors prior to radiation treatment. The treatment couch used, called HexaPOD, is a parallel manipulator with six degrees of freedom which can precisely position heavy loads inside a small region. Despite the HexaPOD not initially built with dynamics in mind, it is used in this work for sustained motion compensation by moving patients such that tumors stay precisely located at the center of the treatment beam during the complete course of treatment. In order to realize real-time tumor motion compensation by means of the HexaPOD, several challanges need to be addressed. Real-time aspects are covered by the adoption of a hard real-time operation system in combination with measurement and estimation of latencies of all physical quantities in the compensation system such as tumor or breathing position measurements. Accurate timing information is respected consistently in the whole system and all software-induced latencies are adaptively compensated for. This requires knowledge of future tumor positions from predictors. Several predictors for breathing and tumor motion predictions are proposed and evaluated in terms of a variety of different performance metrics. Extensions to prediction algorithms are introduced fusing both breathing and tumor position information to allow for predictions without the need of an explicit correlation model. Predictions determine the future motion path of the HexaPOD in order to compensate for tumor motion. Several control schemes are developed to enable reference tracking for the HexaPOD. Based on linear and non-linear dynamic modelling of the HexaPOD with system identification methods, a first controller is derived in the form of a model predictive controller. A second controller is proposed based on an assumption of the working principle of the HexaPOD's internal controller. Finally, a third controller is derived as combination of the first and second one. For each of these controllers, comparative results with real hardware experiments and humans in the loop as well as choices of free parameters are presented and discussed. Apart from precise tracking, emphasis is placed on patient comfort which is of crucial importance for acceptance of the system. It is demonstrated that smooth trajectories can be realized by the controllers to guarantee that patients feel comfortable while their tumor motion is compensated at sub-millimeter accuracies. Overall errors of the system are analyzed by relating them to tracking and prediction errors. By exploiting the properties of different predictors, it is shown that the startup time until tracking is reached can be reduced to only a few seconds, even in the case of an initially at-rest HexaPOD and with no initial knowledge of tumor motion. This makes the system especially suitable for the relatively short-fractionated treatment sessions for lung tumors. The tumor motion compensation system has been developed solely based on standard clinical hardware, found in most treatment rooms. With a simple and flexible design, existing treatment can be updated in a cost-efficient way to introduce motion compensation capabilities. Simultaneously, the system does not impose any constraints on state-of-the-art treatment types such as intensity modulated radiotherapy or volumetric modulated arc therapy. Supporting different compensation modes, the system can be applied to any moving tumor whether its motion is predictable (lung tumors) or unpredictable (prostate tumors). By integration of adequate tumor position determination methods, the system can be easily extended to other tumors as well. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 7 KW - Robotik KW - Bewegungskompensation KW - Regelung KW - Strahlentherapie KW - Vorhersage KW - Tumorbewegung KW - Echzeit KW - Prediction KW - Tumor motion KW - Real-time Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-79045 SN - 978-3-923959-88-4 ER - TY - THES A1 - Busch, Stephan T1 - Robust, Flexible and Efficient Design for Miniature Satellite Systems T1 - Moderne Kleinstsatelliten - Zwischen Robustheit, Flexibilität und Effizienz N2 - Small satellites contribute significantly in the rapidly evolving innovation in space engineering, in particular in distributed space systems for global Earth observation and communication services. Significant mass reduction by miniaturization, increased utilization of commercial high-tech components, and in particular standardization are the key drivers for modern miniature space technology. This thesis addresses key fields in research and development on miniature satellite technology regarding efficiency, flexibility, and robustness. Here, these challenges are addressed by the University of Wuerzburg’s advanced pico-satellite bus, realizing a generic modular satellite architecture and standardized interfaces for all subsystems. The modular platform ensures reusability, scalability, and increased testability due to its flexible subsystem interface which allows efficient and compact integration of the entire satellite in a plug-and-play manner. Beside systematic design for testability, a high degree of operational robustness is achieved by the consequent implementation of redundancy of crucial subsystems. This is combined with efficient fault detection, isolation and recovery mechanisms. Thus, the UWE-3 platform, and in particular the on-board data handling system and the electrical power system, offers one of the most efficient pico-satellite architectures launched in recent years and provides a solid basis for future extensions. The in-orbit performance results of the pico-satellite UWE-3 are presented and summarize successful operations since its launch in 2013. Several software extensions and adaptations have been uploaded to UWE-3 increasing its capabilities. Thus, a very flexible platform for in-orbit software experiments and for evaluations of innovative concepts was provided and tested. N2 - Miniaturisierte Satellitensysteme übernehmen zunehmend eine entscheidende Rolle in der fortschreitenden Globalisierung und Demokratisierung der Raumfahrt. Großes Innovationspotential und neue Kommerzialisierungschancen verspricht der effektive Einsatz von Kleinstsatelliten in zukünftigen fraktionierten Missionen für Erdbeobachtungs- und Kommunikationsanwendungen. Basierend auf vielen kleinen kooperierenden Systemen können diese Systeme zukünftig große multifunktionale Satelliten ergänzen oder ersetzen. Die Herausforderung bei der Entwicklung miniaturisierter Satellitensysteme ist die Gratwanderung zwischen der im Rahmen der Miniaturisierung notwendigen Effizienz, der für die Erfüllung der Mission geforderten Zuverlässigkeit und der wünschenswerten Wiederverwendbarkeit und Erweiterbarkeit zur Realisierung agiler Kleinstsatellitenserien. Diese Arbeit adressiert verschiedene Aspekte für den optimalen Entwurf robuster, flexibler und effizienter Kleinstsatelliten am Beispiel des UWE Pico-Satelliten Bus der Universität Würzburg. Mit dem Ziel der Entwicklung einer soliden Basisplattform für zukünftige Kleinstsatelliten-Formationen wurden entsprechende Designansätze im Rahmen des UWE-3 Projektes in einem integralen Designansatz konsistent umgesetzt. Neben der Entwicklung von effizienten Redundanzkonzepten mit minimalem Overhead für den optimalen Betrieb auf Ressourcen-limitierten Kleinstsatelliten wurde ein modularer Satellitenbus entworfen, der als eine robuste und erweiterbare Basis für zukünftige Missionen dienen soll. Damit realisiert UWE-3 eine der effizientesten Kleinstsatelliten-Architekturen die in den letzten Jahren in den Orbit gebracht wurde. Dargestellte Missionsergebnisse fassen den erfolgreichen Betrieb des Satelliten seit seinem Launch in Jahr 2013 zusammen. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 11 KW - Kleinsatellit KW - Fehlertoleranz KW - Miniaturisierung KW - Modularität KW - Picosatellite KW - Satellit Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-136523 SN - 978-3-945459-10-2 ER - TY - THES A1 - Betz, Christian T1 - Scalable authoring of diagnostic case based training systems T1 - Skalierbare Erstellung diagnostischer fallbasierter Trainingssysteme N2 - Diagnostic Case Based Training Systems (D-CBT) provide learners with a means to learn and exercise knowledge in a realistic context. In medical education, D-CBT Systems present virtual patients to the learners who are asked to examine, diagnose and state therapies for these patients. Due a number of conflicting and changing requirements, e.g. time for learning, authoring effort, several systems were developed so far. These systems range from simple, easy-to-use presentation systems to highly complex knowledge based systems supporting explorative learning. This thesis presents an approach and tools to create D-CBT systems from existing sources (documents, e.g. dismissal records) using existing tools (word processors): Authors annotate and extend the documents to model the knowledge. A scalable knowledge representation is able to capture the content on multiple levels, from simple to highly structured knowledge. Thus, authoring of D-CBT systems requires less prerequisites and pre-knowledge and is faster than approaches using specialized authoring environments. Also, authors can iteratively add and structure more knowledge to adapt training cases to their learners needs. The theses also discusses the application of the same approach to other domains, especially to knowledge acquisition for the Semantic Web. N2 - Fallbasierte diagnostische Trainingssysteme (FDT) ermöglichen es Lernern, Wissen durch Anwendung in einem realistischen Kontext zu erwerben und zu festigen. In der medizinischen Ausbildung präsentieren FDT Systeme virtuelle Patienten, an denen der Lerner die Auswahl und Interpretation der richtigen Untersuchungen, die Diagnostik und die Bestimmung geeigneter Therapien erlernen und üben kann. Eine Vielzahl von Anforderungen durch die Lerner und die Autoren solcher Systeme hat zur Entwicklung unterschiedlicher Trainingsumgebungen geführt. Darunter gibt es einfache, präsentationsorientierte Systeme ebenso wie komplexe wissensbasierte Systeme, die exploratives Lernern erlauben. Diese Dissertation untersucht einen Ansatz und Werkzeuge, um FDT Systeme aus vorhandenen Daten (d.h. Dokumenten, beispielsweise Entlassschreiben) und mit Hilfe bekannter Werkzeuge (d.h. Textverarbeitung) zu entwickeln: Die Autoren annotieren dazu die Dokumente, um die Fälle zu modellieren. Eine skalierbare Wissensrepräsentation kann das so extrahierte Wissen auf verschiedenen Ebenen erfassen, angefangen mit unstrukturierten Elementen bis zu Wissensmodellen mit kausalen Beziehungen. Autoren können mit Hilfe des vorgestellten Ansatzes fallbasierte diagnostische Trainingssysteme mit geringerem Vorwissen und schneller erstellen als mit Hilfe spezialisierter Autorensysteme. Dabei können die Autoren insbesondere die Fälle sukzessive mit weiterem Wissen anreichern und so auf die Anforderungen ihrer Lerner anpassen. In der Dissertation wird darüber hinaus die Anwendung des Ansatzes und der entstandenen Werkzeuge auf andere Domänen untersucht. Besonders interessant ist dabei die Anwendung in der Wissensakquisition für das Semantic Web. KW - Computerunterstütztes Lernen KW - Medizin KW - Wissensrepräsentation KW - Trainingssystem KW - agile Prozesse KW - Semantic Web KW - d3web.Train KW - knowledge representation KW - training systems KW - agile processes KW - semantic web KW - d3web.Train Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-17885 ER - TY - THES A1 - Baier, Pablo A. T1 - Simulator for Minimally Invasive Vascular Interventions: Hardware and Software T1 - VR-Simulation für das Training von Herzkathetereingriffen: Hard- und Softwarelösung N2 - A complete simulation system is proposed that can be used as an educational tool by physicians in training basic skills of Minimally Invasive Vascular Interventions. In the first part, a surface model is developed to assemble arteries having a planar segmentation. It is based on Sweep Surfaces and can be extended to T- and Y-like bifurcations. A continuous force vector field is described, representing the interaction between the catheter and the surface. The computation time of the force field is almost unaffected when the resolution of the artery is increased. The mechanical properties of arteries play an essential role in the study of the circulatory system dynamics, which has been becoming increasingly important in the treatment of cardiovascular diseases. In Virtual Reality Simulators, it is crucial to have a tissue model that responds in real time. In this work, the arteries are discretized by a two dimensional mesh and the nodes are connected by three kinds of linear springs. Three tissue layers (Intima, Media, Adventitia) are considered and, starting from the stretch-energy density, some of the elasticity tensor components are calculated. The physical model linearizes and homogenizes the material response, but it still contemplates the geometric nonlinearity. In general, if the arterial stretch varies by 1% or less, then the agreement between the linear and nonlinear models is trustworthy. In the last part, the physical model of the wire proposed by Konings is improved. As a result, a simpler and more stable method is obtained to calculate the equilibrium configuration of the wire. In addition, a geometrical method is developed to perform relaxations. It is particularly useful when the wire is hindered in the physical method because of the boundary conditions. The physical and the geometrical methods are merged, resulting in efficient relaxations. Tests show that the shape of the virtual wire agrees with the experiment. The proposed algorithm allows real-time executions and the hardware to assemble the simulator has a low cost. N2 - Es wird ein vollständiges Simulationssystem entwickelt, das von Ärzten als Lehrmittel zur Ausbildung grundlegender Fertigkeiten bei Herzkathetereingriffen eingesetzt werden kann. Im ersten Teil wird ein Oberflächenmodell zur Erstellung von Arterien mit planarer Segmentierung entwickelt. Im zweiten Teil werden die Arterien durch ein zweidimensionales Netz diskretisiert, die Knoten werden durch drei Arten linearer Federn verbunden und ausgehend von einer Dehnungsenergie-Dichte-Funktion werden einige Komponenten des Elastizitätstensors berechnet. Im letzten Teil wird das von anderen Autoren vorgeschlagene physikalische Modell des Drahtes verbessert und eine neue geometrische Methode entwickelt. Der vorgeschlagene Algorithmus ermöglicht Echtzeit-Ausführungen. Die Hardware des Simulators hat geringe Herstellungskosten. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 15 KW - Computersimulation KW - Simulator KW - Arterie KW - Elastizitätstensor KW - Herzkatheter KW - Minimally invasive vascular intervention KW - Wire relaxation KW - Artery KW - Elasticity tensor KW - Stiffness KW - educational tool KW - Elastizitätstensor KW - Herzkathetereingriff KW - Software KW - Hardware Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-161190 SN - 978-3-945459-22-5 ER -