TY - RPRT A1 - Loh, Frank A1 - Geißler, Stefan A1 - Hoßfeld, Tobias T1 - LoRaWAN Network Planning in Smart Environments: Towards Reliability, Scalability, and Cost Reduction T2 - Würzburg Workshop on Next-Generation Communication Networks (WueWoWas'22) N2 - The goal in this work is to present a guidance for LoRaWAN planning to improve overall reliability for message transmissions and scalability. At the end, the cost component is discussed. Therefore, a five step approach is presented that helps to plan a LoRaWAN deployment step by step: Based on the device locations, an initial gateway placement is suggested followed by in-depth frequency and channel access planning. After an initial planning phase, updates for channel access and the initial gateway planning is suggested that should also be done periodically during network operation. Since current gateway placement approaches are only studied with random channel access, there is a lot of potential in the cell planning phase. Furthermore, the performance of different channel access approaches is highly related on network load, and thus cell size and sensor density. Last, the influence of different cell planning ideas on expected costs are discussed. KW - Datennetz KW - LoRaWan Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-280829 ER - TY - THES A1 - Krenzer, Adrian T1 - Machine learning to support physicians in endoscopic examinations with a focus on automatic polyp detection in images and videos T1 - Maschinelles Lernen zur Unterstützung von Ärzten bei endoskopischen Untersuchungen mit Schwerpunkt auf der automatisierten Polypenerkennung in Bildern und Videos N2 - Deep learning enables enormous progress in many computer vision-related tasks. Artificial Intel- ligence (AI) steadily yields new state-of-the-art results in the field of detection and classification. Thereby AI performance equals or exceeds human performance. Those achievements impacted many domains, including medical applications. One particular field of medical applications is gastroenterology. In gastroenterology, machine learning algorithms are used to assist examiners during interventions. One of the most critical concerns for gastroenterologists is the development of Colorectal Cancer (CRC), which is one of the leading causes of cancer-related deaths worldwide. Detecting polyps in screening colonoscopies is the essential procedure to prevent CRC. Thereby, the gastroenterologist uses an endoscope to screen the whole colon to find polyps during a colonoscopy. Polyps are mucosal growths that can vary in severity. This thesis supports gastroenterologists in their examinations with automated detection and clas- sification systems for polyps. The main contribution is a real-time polyp detection system. This system is ready to be installed in any gastroenterology practice worldwide using open-source soft- ware. The system achieves state-of-the-art detection results and is currently evaluated in a clinical trial in four different centers in Germany. The thesis presents two additional key contributions: One is a polyp detection system with ex- tended vision tested in an animal trial. Polyps often hide behind folds or in uninvestigated areas. Therefore, the polyp detection system with extended vision uses an endoscope assisted by two additional cameras to see behind those folds. If a polyp is detected, the endoscopist receives a vi- sual signal. While the detection system handles the additional two camera inputs, the endoscopist focuses on the main camera as usual. The second one are two polyp classification models, one for the classification based on shape (Paris) and the other on surface and texture (NBI International Colorectal Endoscopic (NICE) classification). Both classifications help the endoscopist with the treatment of and the decisions about the detected polyp. The key algorithms of the thesis achieve state-of-the-art performance. Outstandingly, the polyp detection system tested on a highly demanding video data set shows an F1 score of 90.25 % while working in real-time. The results exceed all real-time systems in the literature. Furthermore, the first preliminary results of the clinical trial of the polyp detection system suggest a high Adenoma Detection Rate (ADR). In the preliminary study, all polyps were detected by the polyp detection system, and the system achieved a high usability score of 96.3 (max 100). The Paris classification model achieved an F1 score of 89.35 % which is state-of-the-art. The NICE classification model achieved an F1 score of 81.13 %. Furthermore, a large data set for polyp detection and classification was created during this thesis. Therefore a fast and robust annotation system called Fast Colonoscopy Annotation Tool (FastCAT) was developed. The system simplifies the annotation process for gastroenterologists. Thereby the i gastroenterologists only annotate key parts of the endoscopic video. Afterward, those video parts are pre-labeled by a polyp detection AI to speed up the process. After the AI has pre-labeled the frames, non-experts correct and finish the annotation. This annotation process is fast and ensures high quality. FastCAT reduces the overall workload of the gastroenterologist on average by a factor of 20 compared to an open-source state-of-art annotation tool. N2 - Deep Learning ermöglicht enorme Fortschritte bei vielen Aufgaben im Bereich der Computer Vision. Künstliche Intelligenz (KI) liefert ständig neue Spitzenergebnisse im Bereich der Erkennung und Klassifizierung. Dabei erreicht oder übertrifft die Leistung von KI teilweise die menschliche Leistung. Diese Errungenschaften wirken sich auf viele Bereiche aus, darunter auch auf medizinische Anwendungen. Ein besonderer Bereich der medizinischen Anwendungen ist die Gastroenterologie. In der Gastroenterologie werden Algorithmen des maschinellen Lernens eingesetzt, um den Untersucher bei medizinischen Eingriffen zu unterstützen. Eines der größten Probleme für Gastroenterologen ist die Entwicklung von Darmkrebs, die weltweit eine der häufigsten krebsbedingten Todesursachen ist. Die Erkennung von Polypen bei Darmspiegelungen ist das wichtigste Verfahren zur Vorbeugung von Darmkrebs. Dabei untersucht der Gastroenterologe den Dickdarm im Rahmen einer Koloskopie, um z.B. Polypen zu finden. Polypen sind Schleimhautwucherungen, die unterschiedlich stark ausgeprägt sein können. Diese Arbeit unterstützt Gastroenterologen bei ihren Untersuchungen mit automatischen Erkennungssystemen und Klassifizierungssystemen für Polypen. Der Hauptbeitrag ist ein Echtzeitpolypenerkennungssystem. Dieses System kann in jeder gastroenterologischen Praxis weltweit mit Open- Source-Software installiert werden. Das System erzielt Erkennungsergebnisse auf dem neusten Stand der Technik und wird derzeit in einer klinischen Studie in vier verschiedenen Praxen in Deutschland evaluiert. In dieser Arbeit werden zwei weitere wichtige Beiträge vorgestellt: Zum einen ein Polypenerkennungssystem mit erweiterter Sicht, das in einem Tierversuch getestet wurde. Polypen verstecken sich oft hinter Falten oder in nicht untersuchten Bereichen. Daher verwendet das Polypenerkennungssystem mit erweiterter Sicht ein Endoskop, das von zwei zusätzlichen Kameras unterstützt wird, um hinter diese Falten zu sehen. Wenn ein Polyp entdeckt wird, erhält der Endoskopiker ein visuelles Signal. Während das Erkennungssystem die beiden zusätzlichen Kameraeingaben verarbeitet, konzentriert sich der Endoskopiker wie gewohnt auf die Hauptkamera. Das zweite sind zwei Polypenklassifizierungsmodelle, eines für die Klassifizierung anhand der Form (Paris) und das andere anhand der Oberfläche und Textur (NICE-Klassifizierung). Beide Klassifizierungen helfen dem Endoskopiker bei der Behandlung und Entscheidung über den erkannten Polypen. Die Schlüsselalgorithmen der Dissertation erreichen eine Leistung, die dem neuesten Stand der Technik entspricht. Herausragend ist, dass das auf einem anspruchsvollen Videodatensatz getestete Polypenerkennungssystem einen F1-Wert von 90,25 % aufweist, während es in Echtzeit arbeitet. Die Ergebnisse übertreffen alle Echtzeitsysteme für Polypenerkennung in der Literatur. Darüber hinaus deuten die ersten vorläufigen Ergebnisse einer klinischen Studie des Polypenerkennungssystems auf eine hohe Adenomdetektionsrate ADR hin. In dieser Studie wurden alle Polypen durch das Polypenerkennungssystem erkannt, und das System erreichte einen hohe Nutzerfreundlichkeit von 96,3 (maximal 100). Bei der automatischen Klassifikation von Polypen basierend auf der Paris Klassifikations erreichte das in dieser Arbeit entwickelte System einen F1-Wert von 89,35 %, was dem neuesten Stand der Technik entspricht. Das NICE-Klassifikationsmodell erreichte eine F1- Wert von 81,13 %. Darüber hinaus wurde im Rahmen dieser Arbeit ein großer Datensatz zur Polypenerkennung und -klassifizierung erstellt. Dafür wurde ein schnelles und robustes Annotationssystem namens FastCAT entwickelt. Das System vereinfacht den Annotationsprozess für Gastroenterologen. Die Gastroenterologen annotieren dabei nur die wichtigsten Teile des endoskopischen Videos. Anschließend werden diese Videoteile von einer Polypenerkennungs-KI vorverarbeitet, um den Prozess zu beschleunigen. Nachdem die KI die Bilder vorbeschriftet hat, korrigieren und vervollständigen Nicht-Experten die Annotationen. Dieser Annotationsprozess ist schnell und gewährleistet eine hohe Qualität. FastCAT reduziert die Gesamtarbeitsbelastung des Gastroenterologen im Durchschnitt um den Faktor 20 im Vergleich zu einem Open-Source-Annotationstool auf dem neuesten Stand der Technik. KW - Deep Learning KW - Maschinelles Lernen KW - Maschinelles Sehen KW - Machine Learning KW - Object Detection KW - Medical Image Analysis KW - Computer Vision KW - Gastroenterologische Endoskopie KW - Polypektomie Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-319119 ER - TY - RPRT A1 - Riegler, Clemens A1 - Werner, Lennart A1 - Kayal, Hakan T1 - MAPLE: Marsian Autorotation Probe Lander Experiment N2 - The first step towards aerial planetary exploration has been made. Ingenuity shows extremely promising results, and new missions are already underway. Rotorcraft are capable of flight. This capability could be utilized to support the last stages of Entry, Descent, and Landing. Thus, mass and complexity could be scaled down. Autorotation is one method of descent. It describes unpowered descent and landing, typically performed by helicopters in case of an engine failure. MAPLE is suggested to test these procedures and understand autorotation on other planets. In this series of experiments, the Ingenuity helicopter is utilized. Ingenuity would autorotate a ”mid-air-landing” before continuing with normal flight. Ultimately, the collected data shall help to understand autorotation on Mars and its utilization for interplanetary exploration. T3 - Raumfahrttechnik und Extraterrestrik - 2 KW - autorotation KW - descent KW - Mars KW - rotorcraft KW - landing KW - aerospace Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-282390 ER - TY - INPR A1 - Nassourou, Mohamadou T1 - Markup overlap: Improving Fragmentation Method N2 - Overlapping is a common word used to describe documents whose structural dimensions cannot be adequately represented using tree structure. For instance a quotation that starts in one verse and ends in another verse. The problem of overlapping hierarchies is a recurring one, which has been addressed by a variety of approaches. There are XML based solutions as well as Non-XML ones. The XML-based solutions are: multiple documents, empty elements, fragmentation, out-of-line markup, JITT and BUVH. And the Non-XML approaches comprise CONCUR/XCONCUR, MECS, LMNL ...etc. This paper presents shortly state-of-the-art in overlapping hierarchies, and introduces two variations on the TEI fragmentation markup that have several advantages. KW - XML KW - Überlappung KW - Fragmentierung KW - XML KW - Overlapping KW - Fragmentation Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-49084 ER - TY - JOUR A1 - Holfelder, Marc A1 - Mulansky, Lena A1 - Schlee, Winfried A1 - Baumeister, Harald A1 - Schobel, Johannes A1 - Greger, Helmut A1 - Hoff, Andreas A1 - Pryss, Rüdiger T1 - Medical device regulation efforts for mHealth apps during the COVID-19 pandemic — an experience report of Corona Check and Corona Health JF - J — Multidisciplinary Scientific Journal N2 - Within the healthcare environment, mobile health (mHealth) applications (apps) are becoming more and more important. The number of new mHealth apps has risen steadily in the last years. Especially the COVID-19 pandemic has led to an enormous amount of app releases. In most countries, mHealth applications have to be compliant with several regulatory aspects to be declared a “medical app”. However, the latest applicable medical device regulation (MDR) does not provide more details on the requirements for mHealth applications. When developing a medical app, it is essential that all contributors in an interdisciplinary team — especially software engineers — are aware of the specific regulatory requirements beforehand. The development process, however, should not be stalled due to integration of the MDR. Therefore, a developing framework that includes these aspects is required to facilitate a reliable and quick development process. The paper at hand introduces the creation of such a framework on the basis of the Corona Health and Corona Check apps. The relevant regulatory guidelines are listed and summarized as a guidance for medical app developments during the pandemic and beyond. In particular, the important stages and challenges faced that emerged during the entire development process are highlighted. KW - mHealth KW - mobile application KW - MDR KW - medical device regulation KW - medical device software Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-285434 SN - 2571-8800 VL - 4 IS - 2 SP - 206 EP - 222 ER - TY - THES A1 - Sauer, Markus T1 - Mixed-Reality for Enhanced Robot Teleoperation T1 - Mixed-Reality zur verbesserten Fernbedienung von Robotern N2 - In den letzten Jahren ist die Forschung in der Robotik soweit fortgeschritten, dass die Mensch-Maschine Schnittstelle zunehmend die kritischste Komponente für eine hohe Gesamtperformanz von Systemen zur Navigation und Koordination von Robotern wird. In dieser Dissertation wird untersucht wie Mixed-Reality Technologien für Nutzerschnittstellen genutzt werden können, um diese Gesamtperformanz zu erhöhen. Hierzu werden Konzepte und Technologien entwickelt, die durch Evaluierung mit Nutzertest ein optimiertes und anwenderbezogenes Design von Mixed-Reality Nutzerschnittstellen ermöglichen. Er werden somit sowohl die technische Anforderungen als auch die menschlichen Faktoren für ein konsistentes Systemdesign berücksichtigt. Nach einer detaillierten Problemanalyse und der Erstellung eines Systemmodels, das den Menschen als Schlüsselkomponente mit einbezieht, wird zunächst die Anwendung der neuartigen 3D-Time-of-Flight Kamera zur Navigation von Robotern, aber auch für den Einsatz in Mixed-Reality Schnittstellen analysiert und optimiert. Weiterhin wird gezeigt, wie sich der Netzwerkverkehr des Videostroms als wichtigstes Informationselement der meisten Nutzerschnittstellen für die Navigationsaufgabe auf der Netzwerk Applikationsebene in typischen Multi-Roboter Netzwerken mit dynamischen Topologien und Lastsituation optimieren lässt. Hierdurch ist es möglich in sonst in sonst typischen Ausfallszenarien den Videostrom zu erhalten und die Bildrate zu stabilisieren. Diese fortgeschrittenen Technologien werden dann auch dem entwickelten Konzept der generischen 3D Mixed Reality Schnittselle eingesetzt. Dieses Konzept ermöglicht eine integrierte 3D Darstellung der verfügbaren Information, so dass räumliche Beziehungen von Informationen aufrechterhalten werden und somit die Anzahl der mentalen Transformationen beim menschlichen Bediener reduziert wird. Gleichzeitig werden durch diesen Ansatz auch immersive Stereo Anzeigetechnologien unterstützt, welche zusätzlich das räumliche Verständnis der entfernten Situation fördern. Die in der Dissertation vorgestellten und evaluierten Ansätze nutzen auch die Tatsache, dass sich eine lokale Autonomie von Robotern heute sehr robust realisieren lässt. Dies wird zum Beispiel zur Realisierung eines Assistenzsystems mit variabler Autonomie eingesetzt. Hierbei erhält der Fernbediener über eine Kraftrückkopplung kombiniert mit einer integrierten Augmented Reality Schnittstelle, einen Eindruck über die Situation am entfernten Arbeitsbereich, aber auch über die aktuelle Navigationsintention des Roboters. Die durchgeführten Nutzertests belegen die signifikante Steigerung der Navigationsperformanz durch den entwickelten Ansatz. Die robuste lokale Autonomie ermöglicht auch den in der Dissertation eingeführten Ansatz der prädiktiven Mixed-Reality Schnittstelle. Die durch diesen Ansatz entkoppelte Regelschleife über den Menschen ermöglicht es die Sichtbarkeit von unvermeidbaren Systemverzögerungen signifikant zu reduzieren. Zusätzlich können durch diesen Ansatz beide für die Navigation hilfreichen Blickwinkel in einer 3D-Nutzerschnittstelle kombiniert werden – der exozentrische Blickwinkel und der egozentrische Blickwinkel als Augmented Reality Sicht. N2 - With the progress in robotics research the human machine interfaces reach more and more the status of being the major limiting factor for the overall system performance of a system for remote navigation and coordination of robots. In this monograph it is elaborated how mixed reality technologies can be applied for the user interfaces in order to increase the overall system performance. Concepts, technologies, and frameworks are developed and evaluated in user studies which enable for novel user-centered approaches to the design of mixed-reality user interfaces for remote robot operation. Both the technological requirements and the human factors are considered to achieve a consistent system design. Novel technologies like 3D time-of-flight cameras are investigated for the application in the navigation tasks and for the application in the developed concept of a generic mixed reality user interface. In addition it is shown how the network traffic of a video stream can be shaped on application layer in order to reach a stable frame rate in dynamic networks. The elaborated generic mixed reality framework enables an integrated 3D graphical user interface. The realized spatial integration and visualization of available information reduces the demand for mental transformations for the human operator and supports the use of immersive stereo devices. The developed concepts make also use of the fact that local robust autonomy components can be realized and thus can be incorporated as assistance systems for the human operators. A sliding autonomy concept is introduced combining force and visual augmented reality feedback. The force feedback component allows rendering the robot's current navigation intention to the human operator, such that a real sliding autonomy with seamless transitions is achieved. The user-studies prove the significant increase in navigation performance by application of this concept. The generic mixed reality user interface together with robust local autonomy enables a further extension of the teleoperation system to a short-term predictive mixed reality user interface. With the presented concept of operation, it is possible to significantly reduce the visibility of system delays for the human operator. In addition, both advantageous characteristics of a 3D graphical user interface for robot teleoperation- an exocentric view and an augmented reality view – can be combined. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 5 KW - Mobiler Roboter KW - Autonomer Roboter KW - Mensch-Maschine-Schnittstelle KW - Mixed Reality KW - Mensch-Roboter-Interaktion KW - Teleoperation KW - Benutzerschnittstelle KW - Robotik KW - Mensch-Maschine-System KW - Human-Robot-Interaction KW - Teleoperation KW - User Interface Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-55083 SN - 978-3-923959-67-9 ER - TY - JOUR A1 - Djebko, Kirill A1 - Puppe, Frank A1 - Kayal, Hakan T1 - Model-based fault detection and diagnosis for spacecraft with an application for the SONATE triple cube nano-satellite JF - Aerospace N2 - The correct behavior of spacecraft components is the foundation of unhindered mission operation. However, no technical system is free of wear and degradation. A malfunction of one single component might significantly alter the behavior of the whole spacecraft and may even lead to a complete mission failure. Therefore, abnormal component behavior must be detected early in order to be able to perform counter measures. A dedicated fault detection system can be employed, as opposed to classical health monitoring, performed by human operators, to decrease the response time to a malfunction. In this paper, we present a generic model-based diagnosis system, which detects faults by analyzing the spacecraft’s housekeeping data. The observed behavior of the spacecraft components, given by the housekeeping data is compared to their expected behavior, obtained through simulation. Each discrepancy between the observed and the expected behavior of a component generates a so-called symptom. Given the symptoms, the diagnoses are derived by computing sets of components whose malfunction might cause the observed discrepancies. We demonstrate the applicability of the diagnosis system by using modified housekeeping data of the qualification model of an actual spacecraft and outline the advantages and drawbacks of our approach. KW - fault detection KW - model-based diagnosis KW - nano-satellite Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-198836 SN - 2226-4310 VL - 6 IS - 10 ER - TY - THES A1 - Staehle, Barbara T1 - Modeling and Optimization Methods for Wireless Sensor and Mesh Networks T1 - Modellierungs- und Optimierungs-Methoden für drahtlose Sensor- und Mesh-Netze N2 - Im Internet der Zukunft werden Menschen nicht nur mit Menschen, sondern auch mit „Dingen“, und sogar „Dinge“ mit „Dingen“ kommunizieren. Zusätzlich wird das Bedürfnis steigen, immer und überall Zugang zum Internet zu haben. Folglich gewinnen drahtlose Sensornetze (WSNs) und drahtlose Mesh-Netze (WMNs) an Bedeutung, da sie Daten über die Umwelt ins Internet liefern, beziehungsweise einfache Internet-Zugangsmöglichkeiten schaffen. In den vier Teilen dieser Arbeit werden unterschiedliche Modellierungs- und Optimierungsmethoden für WSNs und WMNs vorgestellt. Der Energieverbrauch ist die wichtigste Metrik, wenn es darum geht die Kommunikation in einem WSN zu optimieren. Da sich in der Literatur sehr viele unterschiedliche Energiemodelle finden, untersucht der erste Teil der Arbeit welchen Einfluss unterschiedliche Energiemodelle auf die Optimierung von WSNs haben. Aufbauend auf diesen Überlegungen beschäftigt sich der zweite Teil der Arbeit mit drei Problemen, die überwunden werden müssen um eine standardisierte energieeffiziente Kommunikations-Lösung für WSNs basierend auf IEEE 802.15.4 und ZigBee zu realisieren. Für WMNs sind beide Probleme von geringem Interesse, die Leistung des Netzes jedoch umso mehr. Der dritte Teil der Arbeit führt daher Algorithmen für die Berechnung des Max-Min fairen (MMF) Netzwerk-Durchsatzes in WMNs mit mehreren Linkraten und Internet-Gateways ein. Der letzte Teil der Arbeit untersucht die Auswirkungen des LRA-Konzeptes. Dessen grundlegende Idee ist die folgende. Falls für einen Link eine niedrigere Datenrate als theoretisch möglich verwendet wird, sinkt zwar der Link-Durchsatz, jedoch ist unter Umständen eine größere Anzahl von gleichzeitigen Übertragungen möglich und der Gesamt-Durchsatz des Netzes kann sich erhöhen. Mithilfe einer analytischen LRA Formulierung und einer systematischen Studie kann gezeigt werden, dass eine netzwerkweite Zuordnung robusterer Datenraten als nötig zu einer Erhöhung des MMF Netzwerk-Durchsatzes führt. Desweitern kann gezeigt werden, dass sich LRA positiv auf die Leistungsfähigkeit eines IEEE 802.11 WMNs auswirkt und für die Optimierung des Netzes genutzt werden kann. N2 - In the future Internet, the people-centric communication paradigm will be complemented by a ubiquitous communication among people and devices, or even a communication between devices. This comes along with the need for a more flexible, cheap, widely available Internet access. Two types of wireless networks are considered most appropriate for attaining those goals. While wireless sensor networks (WSNs) enhance the Internet’s reach by providing data about the properties of the environment, wireless mesh networks (WMNs) extend the Internet access possibilities beyond the wired backbone. This monograph contains four chapters which present modeling and optimization methods for WSNs and WMNs. Minimizing energy consumptions is the most important goal of WSN optimization and the literature consequently provides countless energy consumption models. The first part of the monograph studies to what extent the used energy consumption model influences the outcome of analytical WSN optimizations. These considerations enable the second contribution, namely overcoming the problems on the way to a standardized energy-efficient WSN communication stack based on IEEE 802.15.4 and ZigBee. For WMNs both problems are of minor interest whereas the network performance has a higher weight. The third part of the work, therefore, presents algorithms for calculating the max-min fair network throughput in WMNs with multiple link rates and Internet gateway. The last contribution of the monograph investigates the impact of the LRA concept which proposes to systematically assign more robust link rates than actually necessary, thereby allowing to exploit the trade-off between spatial reuse and per-link throughput. A systematical study shows that a network-wide slightly more conservative LRA than necessary increases the throughput of a WMN where max-min fairness is guaranteed. It moreover turns out that LRA is suitable for increasing the performance of a contention-based WMN and is a valuable optimization tool. T3 - Würzburger Beiträge zur Leistungsbewertung Verteilter Systeme - 01/11 KW - Drahtloses Sensorsystem KW - Drahtloses vermaschtes Netz KW - Modellierung KW - Optimierung KW - IEEE 802.11 KW - IEEE 802.15.4 KW - Energieeffizienz KW - Fairness KW - Linkratenanpassung KW - Energy efficiency KW - Fairness KW - Link rate adaptation Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-64884 ER - TY - THES A1 - Hess, Martin T1 - Motion coordination and control in systems of nonholonomic autonomous vehicles T1 - Bewegungskoordination und Regelung in Gruppen nichtholonomer autonomer Fahrzeuge N2 - This work focuses on coordination methods and the control of motion in groups of nonholonomic wheeled mobile robots, in particular of the car-like type. These kind of vehicles are particularly restricted in their mobility. In the main part of this work the two problems of formation motion coordination and of rendezvous in distributed multi-vehicle systems are considered. We introduce several enhancements to an existing motion planning approach for formations of nonholonomic mobile robots. Compared to the original method, the extended approach is able to handle time-varying reference speeds as well as adjustments of the formation's shape during reference trajectory segments with continuously differentiable curvature. Additionally, undesired discontinuities in the speed and steering profiles of the vehicles are avoided. Further, the scenario of snow shoveling on an airfield by utilizing multiple formations of autonomous snowplows is discussed. We propose solutions to the subproblems of motion planning for the formations and tracking control for the individual vehicles. While all situations that might occur have been tested in a simulation environment, we also verified the developed tracking controller in real robot hardware experiments. The task of the rendezvous problem in groups of car-like robots is to drive all vehicles to a common position by means of decentralized control laws. Typically there exists no direct interaction link between all of the vehicles. In this work we present decentralized rendezvous control laws for vehicles with free and with bounded steering. The convergence properties of the approaches are analyzed by utilizing Lyapunov based techniques. Furthermore, they are evaluated within various simulation experiments, while the bounded steering case is also verified within laboratory hardware experiments. Finally we introduce a modification to the bounded steering system that increases the convergence speed at the expense of a higher traveled distance of the vehicles. N2 - Diese Arbeit befasst sich mit Methoden zur Bewegungskoordination und Regelung in Gruppen autonomer, nichtholomer Fahrzeuge, wobei vornehmlich autoähnliche mobile Roboter betrachtet werden. Diese Fahrzeuge sind besonders eingeschränkt in ihrer Bewegungsfreiheit. Im Hauptteil der Arbeit werden die Probleme der Formationsbewegung und des Rendezvous in Gruppen verteilter Fahrzeuge betrachtet. Für ein bestehendes Verfahren zur Bewegungsplanung für Formationen nichtholonomer, mobiler Fahrzeuge werden eine Reihe von Verbesserungen vorgestellt. Diese ermöglichen dem erweiterten Verfahren den Umgang mit Referenztrajektorien mit nicht-konstanter Geschwindigkeit und stetig differenzierbarer Krümmung. Außerdem werden im Gegensatz zum ursprünglichen Ansatz unerwünschte Sprungstellen in den Geschwindigkeits- und Krümmungsprofilen der Fahrzeuge vermieden. Desweiteren wird in dieser Arbeit das Schneeräumen auf Flughafenrollfeldern mittels Formationen autonomer Schneepflugfahrzeuge diskutiert. Dabei werden Lösungen für die Teilprobleme Bewegungsplanung der Formationen und Spurführungsregelung der einzelnen Fahrzeuge vorgestellt. Zusätzlich zu den durchgeführten Simulationen werden außerdem die Ergebnisse von Hardwareexperimenten mit der entwickelten Spurführungsregelung präsentiert. Das Rendezvous-Problem in Gruppen autoähnlicher Roboter besteht darin, die Fahrzeuge durch dezentrale Regelgesetze zu einer gemeinsamen Position in der Ebene zu bewegen. Dabei besteht typischerweise keine direkte Interaktionsverbindung zwischen allen Fahrzeugen der Gruppe. In dieser Arbeit werden verteilte Rendezvous-Regelgesetze für Fahrzeuge mit unbeschränktem und mit beschränktem Lenkwinkel eingeführt und deren Konvergenzeigenschaften mit Methoden zur Stabilitätsanalyse nicht-linearer Systeme untersucht. Die vorgestellten Regelsysteme werden weiterhin anhand von Simulationen und Hardwareexperimenten verifiziert. Schließlich wird noch eine Erweiterung des Systems für Fahrzeuge mit beschränktem Lenkwinkel vorgestellt, welches die Konvergenzgeschwindigkeit auf Kosten der zurückgelegten Distanz der Fahrzeuge erhöht. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 2 KW - Robotik KW - Autonomer Roboter KW - Mobiler Roboter KW - Bewegungskoordination KW - Dezentrale Regelung KW - Nichtlineare Regelung KW - Rendezvous KW - Kooperierende mobile Roboter KW - Formationsbewegung KW - Nichtholonome Fahrzeuge KW - Mehrfahrzeugsysteme KW - Unstetige Regelung KW - Autonomous multi-vehicle systems KW - multi-vehicle formations KW - multi-vehicle rendezvous KW - car-like robots KW - nonholonomic vehicles Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-46442 SN - 978-3-923959-55-6 ER - TY - THES A1 - Kluge, Boris T1 - Motion coordination for a mobile robot in dynamic environments N2 - Generating coordinated motion for a mobile robot operating in natural, continuously changing environments among moving obstacles such as humans is a complex task which requires the solution of various sub problems. In this thesis, we will cover the topics of perception and navigation in dynamic environments, as well as reasoning about the motion of the obstacles and of the robot itself. Perception is mainly considered for a laser range finder, and an according method for obstacle detection and tracking is proposed. Network optimization algorithms are used for data association in the tracking step, resulting in considerable robustness with respect to clutter by small objects. Navigation in general is accomplished using an adaptation of the velocity obstacle approach to the given vehicle kinematics, and cooperative motion coordination between the robot and a human guide is achieved using an appropriate selection rule for collision-free velocities. Next, the robot is enabled to compare its path to the path of a human guide using one of a collection of presented distance measures, which permits the detection of exceptional conditions. Furthermore, a taxonomy for the assessment of situations concerning the robot is presented, and following a summary of existing approaches to more intelligent and comprehensive perception, we propose a method for obstruction detection. Finally, a new approach to reflective navigation behaviors is described where the robot reasons about intelligent moving obstacles in its environment, which allows to adjust the character of the robot motion from regardful and defensive to more self-confident and aggressive behaviors. N2 - Die Realisierung einer koordinierten und effektiven Fortbewegung für einen mobilen Roboter in natürlichen, sich kontinuierlich verändernden Umgebungen unter sich ebenso bewegenden Hindernissen ist eine komplexe Aufgabe, die die Lösung einer Reihe von Unterproblemen voraussetzt. Die vorliegende Arbeit beschäftigt sich sowohl mit den Themen der Wahrnehmung und Fortbewegung in veränderlichen Umgebungen, als auch mit Methoden zur Analyse der Hindernisbewegungen in Zusammenhang mit der Roboterbewegung selbst. Die Wahrnehmung wird in erster Linie anhand von Laserscannern betrachtet, und ein entsprechendes Verfahren zur Hindernisdetektion und -verfolung wird vorgestellt. Dabei werden Verfahren der globalen Netzwerkoptimierung eingesetzt, um Korrespondenzen zwischen Objekten aus den Einzelbildern herzustellen, was sich positiv auf die Robustheit gegenüber Störungen durch sporadische kleine Objekte auswirkt. Die Navigation basiert auf einer Adaption des sog. "Velocity Obstacle" Ansatzes auf die vorhandene Fahrzeugkinematik, und eine kooperative Bewegungskoordination (Roboter begleitet Mensch) wird durch eine geeignete Auswahlregel für kollisionsfreie Geschwindigkeiten realisiert. Anschließend werden verschiedene Distanzmaße eingeführt, anhand derer sich etwa der Pfad des Roboters mit dem Pfad seiner Begleitperson vergleichen lässt. Weiter wird eine Klassifizierung von Situationen vorgenommen, in die der Roboter potentiell involviert sein kann, und nach einer Übersicht über existierende Ansätze zur automatischen Intentionserkennung wird ein praktikabler Ansatz zur Erkennung gezielter Behinderungen eines mobilen Roboters vorgestellt. Die Arbeit schließt mit einem neuen Ansatz der Bewegungsplanung in dynamischen Umgebungen, der auf rekursiven Modellen des Roboters von seinem Gegenüber basiert, d.h. der Roboter berechnet zunächst, wie er sich in der Situation des (intelligenten, beweglichen) Hindernisses fortbewegen würde, und bezieht dies in die Entscheidung über die eigene Fortbewegung mit ein. Je nach Rekursionstiefe entstehen hierdurch Verhaltensweisen unterschiedlichen Charakters für den Roboter. T2 - Bewegungskoordination für einen mobilen Roboter in dynamischen Umgebungen KW - Bewegungsablauf KW - Roboter KW - Roboter KW - Bewegungsplanung KW - dynamische Umgebungen KW - Robot KW - Motion Planning KW - Dynamic Environments Y1 - 2004 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-15508 ER - TY - THES A1 - Borrmann, Dorit T1 - Multi-modal 3D mapping - Combining 3D point clouds with thermal and color information T1 - Multi-modale 3D-Kartierung - Kombination von 3D-Punktwolken mit Thermo- und Farbinformation N2 - Imagine a technology that automatically creates a full 3D thermal model of an environment and detects temperature peaks in it. For better orientation in the model it is enhanced with color information. The current state of the art for analyzing temperature related issues is thermal imaging. It is relevant for energy efficiency but also for securing important infrastructure such as power supplies and temperature regulation systems. Monitoring and analysis of the data for a large building is tedious as stable conditions need to be guaranteed for several hours and detailed notes about the pose and the environment conditions for each image must be taken. For some applications repeated measurements are necessary to monitor changes over time. The analysis of the scene is only possible through expertise and experience. This thesis proposes a robotic system that creates a full 3D model of the environment with color and thermal information by combining thermal imaging with the technology of terrestrial laser scanning. The addition of a color camera facilitates the interpretation of the data and allows for other application areas. The data from all sensors collected at different positions is joined in one common reference frame using calibration and scan matching. The first part of the thesis deals with 3D point cloud processing with the emphasis on accessing point cloud data efficiently, detecting planar structures in the data and registering multiple point clouds into one common coordinate system. The second part covers the autonomous exploration and data acquisition with a mobile robot with the objective to minimize the unseen area in 3D space. Furthermore, the combination of different modalities, color images, thermal images and point cloud data through calibration is elaborated. The last part presents applications for the the collected data. Among these are methods to detect the structure of building interiors for reconstruction purposes and subsequent detection and classification of windows. A system to project the gathered thermal information back into the scene is presented as well as methods to improve the color information and to join separately acquired point clouds and photo series. A full multi-modal 3D model contains all the relevant geometric information about the recorded scene and enables an expert to fully analyze it off-site. The technology clears the path for automatically detecting points of interest thereby helping the expert to analyze the heat flow as well as localize and identify heat leaks. The concept is modular and neither limited to achieving energy efficiency nor restricted to the use in combination with a mobile platform. It also finds its application in fields such as archaeology and geology and can be extended by further sensors. N2 - Man stelle sich eine Technologie vor, die automatisch ein vollständiges 3D-Thermographiemodell einer Umgebung generiert und Temperaturspitzen darin erkennt. Zur besseren Orientierung innerhalb des Modells ist dieses mit Farbinformationen erweitert. In der Analyse temperaturrelevanter Fragestellungen sind Thermalbilder der Stand der Technik. Darunter fallen Energieeffizienz und die Sicherung wichtiger Infrastruktur, wie Energieversorgung und Systeme zur Temperaturregulierung. Die Überwachung und anschließende Analyse der Daten eines großen Gebäudes ist aufwändig, da über mehrere Stunden stabile Bedingungen garantiert und detaillierte Aufzeichnungen über die Aufnahmeposen und die Umgebungsverhältnisse für jedes Wärmebild erstellt werden müssen. Einige Anwendungen erfordern wiederholte Messungen, um Veränderungen über die Zeit zu beobachten. Eine Analyse der Szene ist nur mit Erfahrung und Expertise möglich. Diese Arbeit stellt ein Robotersystem vor, das durch Kombination von Thermographie mit terrestrischem Laserscanning ein vollständiges 3D Modell der Umgebung mit Farb- und Temperaturinformationen erstellt. Die ergänzende Farbkamera vereinfacht die Interpretation der Daten und eröffnet weitere Anwendungsfelder. Die an unterschiedlichen Positionen aufgenommenen Daten aller Sensoren werden durch Kalibrierung und Scanmatching in einem gemeinsamen Bezugssystem zusammengefügt. Der erste Teil der Arbeit behandelt 3D-Punktwolkenverarbeitung mit Schwerpunkt auf effizientem Punktzugriff, Erkennung planarer Strukturen und Registrierung mehrerer Punktwolken in einem gemeinsamen Koordinatensystem. Der zweite Teil beschreibt die autonome Erkundung und Datenakquise mit einem mobilen Roboter, mit dem Ziel, die bisher nicht erfassten Bereiche im 3D-Raum zu minimieren. Des Weiteren wird die Kombination verschiedener Modalitäten, Farbbilder, Thermalbilder und Punktwolken durch Kalibrierung ausgearbeitet. Den abschließenden Teil stellen Anwendungsszenarien für die gesammelten Daten dar, darunter Methoden zur Erkennung der Innenraumstruktur für die Rekonstruktion von Gebäuden und der anschließenden Erkennung und Klassifizierung von Fenstern. Ein System zur Rückprojektion der gesammelten Thermalinformation in die Umgebung wird ebenso vorgestellt wie Methoden zur Verbesserung der Farbinformationen und zum Zusammenfügen separat aufgenommener Punktwolken und Fotoreihen. Ein vollständiges multi-modales 3D Modell enthält alle relevanten geometrischen Informationen der aufgenommenen Szene und ermöglicht einem Experten, diese standortunabhängig zu analysieren. Diese Technologie ebnet den Weg für die automatische Erkennung relevanter Bereiche und für die Analyse des Wärmeflusses und vereinfacht somit die Lokalisierung und Identifikation von Wärmelecks für den Experten. Das vorgestellte modulare Konzept ist weder auf den Anwendungsfall Energieeffizienz beschränkt noch auf die Verwendung einer mobilen Plattform angewiesen. Es ist beispielsweise auch in Feldern wie der Archäologie und Geologie einsetzbar und kann durch zusätzliche Sensoren erweitert werden. T3 - Forschungsberichte in der Robotik = Research Notes in Robotics - 14 KW - Punktwolke KW - Lidar KW - Thermografie KW - Robotik KW - 3D point cloud KW - Laser scanning KW - Robotics KW - 3D thermal mapping KW - Registration Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-157085 SN - 978-3-945459-20-1 SN - 1868-7474 SN - 1868-7466 ER - TY - THES A1 - Wirth, Hans-Christoph T1 - Multicriteria Approximation of Network Design and Network Upgrade Problems T1 - Mehrkriterien-Approximation von Netzwerk-Design- und Netzwerk-Ausbau-Problemen N2 - Network planning has come to great importance during the past decades. Today's telecommunication, traffic systems, and logistics would not have been evolved to the current state without careful analysis of the underlying network problems and precise implementation of the results obtained from those examinations. Graphs with node and arc attributes are a very useful tool to model realistic applications, while on the other hand they are well understood in theory. We investigate network design problems which are motivated particularly from applications in communication networks and logistics. Those problems include the search for homogeneous subgraphs in edge labeled graphs where either the total number of labels or the reload cost are subject to optimize. Further, we investigate some variants of the dial a ride problem. On the other hand, we use node and edge upgrade models to deal with the fact that in many cases one prefers to change existing networks rather than implementing a newly computed solution from scratch. We investigate the construction of bottleneck constrained forests under a node upgrade model, as well as several flow cost problems under a edge based upgrade model. All problems are examined within a framework of multi-criteria optimization. Many of the problems can be shown to be NP-hard, with the consequence that, under the widely accepted assumption that P is not equal to NP, there cannot exist efficient algorithms for solving the problems. This motivates the development of approximation algorithms which compute near-optimal solutions with provable performance guarantee in polynomial time. N2 - Netzplanung hat in den vergangenen Jahrzehnten an Bedeutung zugenommen. Der heutige Stand im Bereich von Telekommunikation, Verkehrsnetzen und in der Logistik wäre nicht in dem Maße erreicht worden, wenn nicht die zugrundeliegenden Netzplanungsprobleme sorgfältig analysiert und die daraus gewonnenen Erkenntnisse in die Realisierung eingeflossen wären. Für die Modellierung der durch die Praxis vorgegebenen Probleme erweisen sich Graphen mit Knoten- und Kantenbewertungen als gut geeignet, zumal diese Strukturen auch in der Theorie bereits gut untersucht sind. Wir betrachten Netzwerk-Design-Probleme aus dem Bereich der Planung von Kommunikations- und Logistiknetzwerken. Gegenstand ist zunächst die Suche nach homogenen Teilgraphen in Graphen mit Kantenlabels, wobei einerseits die Gesamtszahl der benutzten Labels minimiert wird, andererseits die Kosten unter einem Umladekosten-Modell optimiert werden. Weiter werden einige Varianten des Dial-A-Ride-Problems untersucht. Im zweiten Teil der Arbeit werden Netzwerk-Ausbau-Probleme betrachtet. Dies trägt der Tatsache Rechung, dass in vielen praktischen Fällen nur die Abänderung bestehender Netze und nicht die Neukonstruktion von Netzen in Frage kommt. Alle Probleme werden im Rahmen der Mehrkriterien-Optimierung betrachtet. Viele der betrachteten Probleme lassen sich als NP-hart nachweisen. Dies hat zur Folge, dass es - unter der gängigen Annahme, dass P ungleich NP ist - keine effizienten Lösungsalgorithmen geben kann. Daher entwickeln wir Approximationsalgorithmen, die in Polynomialzeit Näherungslösungen mit beweisbarer Gütegarantie berechnen. KW - Netzplantechnik KW - Rechnernetz KW - Approximation KW - network design KW - network upgrade KW - approximation algorithms KW - edge labeled graphs KW - reload cost KW - spanning tree KW - dial a ride KW - constrained forest Y1 - 2001 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-2845 ER - TY - THES A1 - Höhn, Holger T1 - Multimediale, datenbankgestützte Lehr- und Lernplattformen T1 - Multimedia, Database Supported Teaching and Learning Environments N2 - Die Dissertation befaßt sich mit der Entwicklung einer multimedialen, datenbankgestützten Lehr- und Lernplattform. Die entwickelten Module ermöglichen und erweitern nicht nur die Möglichkeit des Selbststudiums für den Studenten sondern erleichtern auch die Arbeit der Dozenten. Außerdem wird auch die Zusammenarbeit und der Austausch von Lernobjekten zwischen verschiedenen Institutionen ermöglicht. In der Lehr- und Lernplattform können verschiedene Lernobjekt-Typen verwaltet werden. Exemplarisch wurden die Typen Bilder, 3D-Animationen, Vorlesungen, Lerntexte, Fallbeispiele und Quizelemente integriert. Die Lehr- und Lernplattform besteht aus drei Bausteinen: 1. In der Lernobjekt-Datenbank werden alle Lernobjekt-Typen und Lernobjekte verwaltet. 2. Autorenwerkzeuge dienen zur Erstellung von Lernobjekten. 3. In der Lernplattform werden die Lernobjekte den Studenten zum (Selbst-)Lernen präsentiert. Neben den Vorteilen, die der Einsatz von E-Learning im allgemeinen bietet, wie die flexible Lernorganisation oder die Nutzung von Lerninhalten unabhängig von Ort und Zeit, zeichnet sich die entwickelte Lehr- und Lernplattform besonders durch folgende Punkte aus: Generierung von Lerninhalten höherer Qualität durch multizentrische Expertenbündelung und Arbeitsteilung, Erweiterbarkeit auf andere, neue Lernobjekt-Typen, Verwaltbarkeit, Konsistenz, Flexibilität, geringer Verwaltungsaufwand, Navigationsmöglichkeiten für den Studenten, Personalisierbarkeit und Konformität zu internationalen Standards. Sowohl bei der Modellierung als auch bei der Umsetzung wurde darauf geachtet, möglichst gut die Anforderungen der Dermatologie bei gleichzeitiger Erweiterbarkeit auf andere, ähnliche Szenarien zu erfüllen. Besonders einfach sollte die Anpassung der Plattform für andere bildorientierte Disziplinen sein. N2 - In this thesis a multimedia teaching and learning environment was developed. The center of interest are learning objects which can be classified into different types. The types and objects are stored and adminstered in a database. As examples lectures, learning texts, 3D-animations, images, videos and quiz elements were integrated. For the generation of learning objects authoring tools were developed for each type. The teaching and learning environment offers the following features: lectureres are supported in preparing lectures. Because learning objects can be exchanged between different environments, the generation of "high quality" objects is encouraged. New types of learning objects can be integrated easily. Students are able to learn time-independent. The system was tested in dermatology, but the adaption to other, especially visually oriented disciplines is easy. KW - Multimedia KW - Anwendung KW - Forschung KW - Lehre KW - Lehre KW - Multimedia KW - Datenbanken KW - Lernen KW - Multimedia KW - Learning KW - Teaching KW - Databases Y1 - 2002 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-4049 ER - TY - THES A1 - Reitwießner, Christian T1 - Multiobjective Optimization and Language Equations T1 - Mehrkriterielle Optimierung und Sprachgleichungen N2 - Praktische Optimierungsprobleme beinhalten oft mehrere gleichberechtigte, sich jedoch widersprechende Kriterien. Beispielsweise will man bei einer Reise zugleich möglichst schnell ankommen, sie soll aber auch nicht zu teuer sein. Im ersten Teil dieser Arbeit wird die algorithmische Beherrschbarkeit solcher mehrkriterieller Optimierungsprobleme behandelt. Es werden zunächst verschiedene Lösungsbegriffe diskutiert und auf ihre Schwierigkeit hin verglichen. Interessanterweise stellt sich heraus, dass diese Begriffe für ein einkriterielles Problem stets gleich schwer sind, sie sich ab zwei Kriterien allerdings stark unterscheiden könen (außer es gilt P = NP). In diesem Zusammenhang wird auch die Beziehung zwischen Such- und Entscheidungsproblemen im Allgemeinen untersucht. Schließlich werden neue und verbesserte Approximationsalgorithmen für verschieden Varianten des Problems des Handlungsreisenden gefunden. Dabei wird mit Mitteln der Diskrepanztheorie eine Technik entwickelt, die ein grundlegendes Hindernis der Mehrkriteriellen Optimierung aus dem Weg schafft: Gegebene Lösungen so zu kombinieren, dass die neue Lösung in allen Kriterien möglichst ausgewogen ist und gleichzeitig die Struktur der Lösungen nicht zu stark zerstört wird. Der zweite Teil der Arbeit widmet sich verschiedenen Aspekten von Gleichungssystemen für (formale) Sprachen. Einerseits werden konjunktive und Boolesche Grammatiken untersucht. Diese sind Erweiterungen der kontextfreien Grammatiken um explizite Durchschnitts- und Komplementoperationen. Es wird unter anderem gezeigt, dass man bei konjunktiven Grammatiken die Vereinigungsoperation stark einschränken kann, ohne dabei die erzeugte Sprache zu ändern. Außerdem werden bestimmte Schaltkreise untersucht, deren Gatter keine Wahrheitswerte sondern Mengen von Zahlen berechnen. Für diese Schaltkreise wird das Äquivalenzproblem betrachtet, also die Frage ob zwei gegebene Schaltkreise die gleiche Menge berechnen oder nicht. Es stellt sich heraus, dass, abhängig von den erlaubten Gattertypen, die Komplexität des Äquivalenzproblems stark variiert und für verschiedene Komplexitätsklassen vollständig ist, also als (parametrisierter) Vertreter für diese Klassen stehen kann. N2 - Practical optimization problems often comprise several incomparable and conflicting objectives. When booking a trip using several means of transport, for instance, it should be fast and at the same time not too expensive. The first part of this thesis is concerned with the algorithmic solvability of such multiobjective optimization problems. Several solution notions are discussed and compared with respect to their difficulty. Interestingly, these solution notions are always equally difficulty for a single-objective problem and they differ considerably already for two objectives (unless P = NP). In this context, the difference between search and decision problems is also investigated in general. Furthermore, new and improved approximation algorithms for several variants of the traveling salesperson problem are presented. Using tools from discrepancy theory, a general technique is developed that helps to avoid an obstacle that is often hindering in multiobjective approximation: The problem of combining two solutions such that the new solution is balanced in all objectives and also mostly retains the structure of the original solutions. The second part of this thesis is dedicated to several aspects of systems of equations for (formal) languages. Firstly, conjunctive and Boolean grammars are studied, which are extensions of context-free grammars by explicit intersection and complementation operations, respectively. Among other results, it is shown that one can considerably restrict the union operation on conjunctive grammars without changing the generated language. Secondly, certain circuits are investigated whose gates do not compute Boolean values but sets of natural numbers. For these circuits, the equivalence problem is studied, i.\,e.\ the problem of deciding whether two given circuits compute the same set or not. It is shown that, depending on the allowed types of gates, this problem is complete for several different complexity classes and can thus be seen as a parametrized) representative for all those classes. KW - Mehrkriterielle Optimierung KW - Approximationsalgorithmus KW - Travelling-salesman-Problem KW - Boolesche Grammatik KW - Theoretische Informatik KW - Komplexitätstheorie KW - Boolean Grammar Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-70146 ER - TY - RPRT A1 - Navade, Piyush A1 - Maile, Lisa A1 - German, Reinhard T1 - Multiple DCLC Routing Algorithms for Ultra-Reliable and Time-Sensitive Applications T2 - KuVS Fachgespräch - Würzburg Workshop on Modeling, Analysis and Simulation of Next-Generation Communication Networks 2023 (WueWoWAS’23) N2 - This paper discusses the problem of finding multiple shortest disjoint paths in modern communication networks, which is essential for ultra-reliable and time-sensitive applications. Dijkstra’s algorithm has been a popular solution for the shortest path problem, but repetitive use of it to find multiple paths is not scalable. The Multiple Disjoint Path Algorithm (MDPAlg), published in 2021, proposes the use of a single full graph to construct multiple disjoint paths. This paper proposes modifications to the algorithm to include a delay constraint, which is important in time-sensitive applications. Different delay constraint least-cost routing algorithms are compared in a comprehensive manner to evaluate the benefits of the adapted MDPAlg algorithm. Fault tolerance, and thereby reliability, is ensured by generating multiple link-disjoint paths from source to destination. KW - Dijkstra’s algorithm KW - shortest path routing KW - disjoint multi-paths KW - delay constrained KW - least cost Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-322177 ER - TY - THES A1 - Höhn, Winfried T1 - Mustererkennung in Frühdrucken T1 - Pattern Perception in Early Printed Books N2 - No abstract available KW - Mustererkennung KW - Frühdruck KW - pattern perception KW - early printed books Y1 - 2006 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-30429 ER - TY - JOUR A1 - Oberdörfer, Sebastian A1 - Birnstiel, Sandra A1 - Latoschik, Marc Erich A1 - Grafe, Silke T1 - Mutual Benefits: Interdisciplinary Education of Pre-Service Teachers and HCI Students in VR/AR Learning Environment Design JF - Frontiers in Education N2 - The successful development and classroom integration of Virtual (VR) and Augmented Reality (AR) learning environments requires competencies and content knowledge with respect to media didactics and the respective technologies. The paper discusses a pedagogical concept specifically aiming at the interdisciplinary education of pre-service teachers in collaboration with human-computer interaction students. The students’ overarching goal is the interdisciplinary realization and integration of VR/AR learning environments in teaching and learning concepts. To assist this approach, we developed a specific tutorial guiding the developmental process. We evaluate and validate the effectiveness of the overall pedagogical concept by analyzing the change in attitudes regarding 1) the use of VR/AR for educational purposes and in competencies and content knowledge regarding 2) media didactics and 3) technology. Our results indicate a significant improvement in the knowledge of media didactics and technology. We further report on four STEM learning environments that have been developed during the seminar. KW - interdisciplinary education KW - virtual reality KW - augmented reality KW - serious games KW - learning environments KW - teacher education Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-241612 SN - 2504-284X VL - 6 ER - TY - JOUR A1 - Bencurova, Elena A1 - Shityakov, Sergey A1 - Schaack, Dominik A1 - Kaltdorf, Martin A1 - Sarukhanyan, Edita A1 - Hilgarth, Alexander A1 - Rath, Christin A1 - Montenegro, Sergio A1 - Roth, Günter A1 - Lopez, Daniel A1 - Dandekar, Thomas T1 - Nanocellulose composites as smart devices with chassis, light-directed DNA Storage, engineered electronic properties, and chip integration JF - Frontiers in Bioengineering and Biotechnology N2 - The rapid development of green and sustainable materials opens up new possibilities in the field of applied research. Such materials include nanocellulose composites that can integrate many components into composites and provide a good chassis for smart devices. In our study, we evaluate four approaches for turning a nanocellulose composite into an information storage or processing device: 1) nanocellulose can be a suitable carrier material and protect information stored in DNA. 2) Nucleotide-processing enzymes (polymerase and exonuclease) can be controlled by light after fusing them with light-gating domains; nucleotide substrate specificity can be changed by mutation or pH change (read-in and read-out of the information). 3) Semiconductors and electronic capabilities can be achieved: we show that nanocellulose is rendered electronic by iodine treatment replacing silicon including microstructures. Nanocellulose semiconductor properties are measured, and the resulting potential including single-electron transistors (SET) and their properties are modeled. Electric current can also be transported by DNA through G-quadruplex DNA molecules; these as well as classical silicon semiconductors can easily be integrated into the nanocellulose composite. 4) To elaborate upon miniaturization and integration for a smart nanocellulose chip device, we demonstrate pH-sensitive dyes in nanocellulose, nanopore creation, and kinase micropatterning on bacterial membranes as well as digital PCR micro-wells. Future application potential includes nano-3D printing and fast molecular processors (e.g., SETs) integrated with DNA storage and conventional electronics. This would also lead to environment-friendly nanocellulose chips for information processing as well as smart nanocellulose composites for biomedical applications and nano-factories. KW - nanocellulose KW - DNA storage KW - light-gated proteins KW - single-electron transistors KW - protein chip Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-283033 SN - 2296-4185 VL - 10 ER - TY - THES A1 - Fleszar, Krzysztof T1 - Network-Design Problems in Graphs and on the Plane T1 - Netzwerk-Design-Probleme in Graphen und auf der Ebene N2 - A network design problem defines an infinite set whose elements, called instances, describe relationships and network constraints. It asks for an algorithm that, given an instance of this set, designs a network that respects the given constraints and at the same time optimizes some given criterion. In my thesis, I develop algorithms whose solutions are optimum or close to an optimum value within some guaranteed bound. I also examine the computational complexity of these problems. Problems from two vast areas are considered: graphs and the Euclidean plane. In the Maximum Edge Disjoint Paths problem, we are given a graph and a subset of vertex pairs that are called terminal pairs. We are asked for a set of paths where the endpoints of each path form a terminal pair. The constraint is that any two paths share at most one inner vertex. The optimization criterion is to maximize the cardinality of the set. In the hard-capacitated k-Facility Location problem, we are given an integer k and a complete graph where the distances obey a given metric and where each node has two numerical values: a capacity and an opening cost. We are asked for a subset of k nodes, called facilities, and an assignment of all the nodes, called clients, to the facilities. The constraint is that the number of clients assigned to a facility cannot exceed the facility's capacity value. The optimization criterion is to minimize the total cost which consists of the total opening cost of the facilities and the total distance between the clients and the facilities they are assigned to. In the Stabbing problem, we are given a set of axis-aligned rectangles in the plane. We are asked for a set of horizontal line segments such that, for every rectangle, there is a line segment crossing its left and right edge. The optimization criterion is to minimize the total length of the line segments. In the k-Colored Non-Crossing Euclidean Steiner Forest problem, we are given an integer k and a finite set of points in the plane where each point has one of k colors. For every color, we are asked for a drawing that connects all the points of the same color. The constraint is that drawings of different colors are not allowed to cross each other. The optimization criterion is to minimize the total length of the drawings. In the Minimum Rectilinear Polygon for Given Angle Sequence problem, we are given an angle sequence of left (+90°) turns and right (-90°) turns. We are asked for an axis-parallel simple polygon where the angles of the vertices yield the given sequence when walking around the polygon in counter-clockwise manner. The optimization criteria considered are to minimize the perimeter, the area, and the size of the axis-parallel bounding box of the polygon. N2 - Ein Netzwerk-Design-Problem definiert eine unendliche Menge, deren Elemente, als Instanzen bezeichnet, Beziehungen und Beschränkungen in einem Netzwerk beschreiben. Die Lösung eines solchen Problems besteht aus einem Algorithmus, der auf die Eingabe einer beliebigen Instanz dieser Menge ein Netzwerk entwirft, welches die gegebenen Beschränkungen einhält und gleichzeitig ein gegebenes Kriterium optimiert. In meiner Dissertation habe ich Algorithmen entwickelt, deren Netzwerke stets optimal sind oder nachweisbar nahe am Optimum liegen. Zusätzlich habe ich die Berechnungskomplexität dieser Probleme untersucht. Dabei wurden Probleme aus zwei weiten Gebieten betrachtet: Graphen und der Euklidische Ebene. Im Maximum-Edge-Disjoint-Paths-Problem besteht die Eingabe aus einem Graphen und einer Teilmenge von Knotenpaaren, die wir mit Terminalpaare bezeichnen. Gesucht ist eine Menge von Pfaden, die Terminalpaare verbinden. Die Beschränkung ist, dass keine zwei Pfade einen gleichen inneren Knoten haben dürfen. Das Optimierungskriterium ist die Maximierung der Kardinalität dieser Menge. Im Hard-Capacitated-k-Facility-Location-Problem besteht die Eingabe aus einer Ganzzahl k und einem vollständigen Graphen, in welchem die Distanzen einer gegebenen Metrik unterliegen und in welchem jedem Knoten sowohl eine numerische Kapazität als auch ein Eröffnungskostenwert zugeschrieben ist. Gesucht ist eine Teilmenge von k Knoten, Facilities genannt, und eine Zuweisung aller Knoten, Clients genannt, zu den Facilities. Die Beschränkung ist, dass die Anzahl der Clients, die einer Facility zugewiesen sind, nicht deren Kapazität überschreiten darf. Das Optimierungskriterium ist die Minimierung der Gesamtkosten bestehend aus den Gesamteröffnungskosten der Facilities sowie der Gesamtdistanz zwischen den Clients und den ihnen zugewiesenen Facilities. Im Stabbing-Problem besteht die Eingabe aus einer Menge von achsenparallelen Rechtecken in der Ebene. Gesucht ist eine Menge von horizontalen Geradenstücken mit der Randbedingung, dass die linke und rechte Seite eines jeden Rechtecks von einem Geradenstück verbunden ist. Das Optimierungskriterium ist die Minimierung der Gesamtlänge aller Geradenstücke. Im k-Colored-Non-Crossing-Euclidean-Steiner-Forest-Problem besteht die Eingabe aus einer Ganzzahl k und einer endlichen Menge von Punkten in der Ebene, wobei jeder Punkt in einer von k Farben gefärbt ist. Gesucht ist für jede Farbe eine Zeichnung, in welcher alle Punkte der Farbe verbunden sind. Die Beschränkung ist, dass Zeichnungen verschiedener Farben sich nicht kreuzen dürfen. Das Optimierungskriterium ist die Minimierung des Gesamtintenverbrauchs, das heißt, der Gesamtlänge der Zeichnungen. Im Minimum-Rectilinear-Polygon-for-Given-Angle-Sequence-Problem besteht die Eingabe aus einer Folge von Links- (+90°) und Rechtsabbiegungen (-90°). Gesucht ist ein achsenparalleles Polygon dessen Eckpunkte die gegebene Folge ergeben, wenn man das Polygon gegen den Uhrzeigersinn entlangläuft. Die Optimierungskriterien sind die Minimierung des Umfangs und der inneren Fläche des Polygons sowie der Größe des notwendigen Zeichenblattes, d.h., des kleinsten Rechteckes, das das Polygon einschließt. N2 - Given points in the plane, connect them using minimum ink. Though the task seems simple, it turns out to be very time consuming. In fact, scientists believe that computers cannot efficiently solve it. So, do we have to resign? This book examines such NP-hard network-design problems, from connectivity problems in graphs to polygonal drawing problems on the plane. First, we observe why it is so hard to optimally solve these problems. Then, we go over to attack them anyway. We develop fast algorithms that find approximate solutions that are very close to the optimal ones. Hence, connecting points with slightly more ink is not hard. KW - Euklidische Ebene KW - Algorithmus KW - Komplexität KW - NP-schweres Problem KW - Graph KW - approximation algorithm KW - hardness KW - optimization KW - graphs KW - network KW - Optimierungsproblem KW - Approximationsalgorithmus KW - complexity KW - Euclidean plane Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-154904 SN - 978-3-95826-076-4 (Print) SN - 978-3-95826-077-1 (Online) N1 - Parallel erschienen als Druckausgabe in Würzburg University Press, ISBN 978-3-95826-076-4, 28,90 EUR. PB - Würzburg University Press CY - Würzburg ET - 1. Auflage ER - TY - RPRT A1 - Simon, Manuel A1 - Gallenmüller, Sebastian A1 - Carle, Georg T1 - Never Miss Twice - Add-On-Miss Table Updates in Software Data Planes T2 - KuVS Fachgespräch - Würzburg Workshop on Modeling, Analysis and Simulation of Next-Generation Communication Networks 2023 (WueWoWAS’23) N2 - State Management at line rate is crucial for critical applications in next-generation networks. P4 is a language used in software-defined networking to program the data plane. The data plane can profit in many circumstances when it is allowed to manage its state without any detour over a controller. This work is based on a previous study by investigating the potential and performance of add-on-miss insertions of state by the data plane. The state keeping capabilities of P4 are limited regarding the amount of data and the update frequency. We follow the tentative specification of an upcoming portable-NIC-architecture and implement these changes into the software P4 target T4P4S. We show that insertions are possible with only a slight overhead compared to lookups and evaluate the influence of the rate of insertions on their latency. KW - SDN KW - state management KW - P4 KW - Add-on-Miss Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-322071 ER -