TY - THES A1 - Schug, Benedikt T1 - Untersuchungen zur Ursache und Beeinflussung des Kriechverhaltens von Gips T1 - Investigations into the origin and the influencing of the creep behavior of gypsum N2 - In dieser Arbeit konnte ein weiterer und möglicherweise entscheidender Schritt zur Aufklärung des Kriechmechanismus von Gips gemacht und darauf aufbauend Kriterien, Wege und Strategien aufgezeigt werden, um neue Antikriechmittelsubstanzen zu identifizieren oder vorhandene Kriechmittel gezielt zu verbessern. Die Gültigkeit und Praxistauglichkeit der Kriterien wurde exemplarisch nachgewiesen. Die Basis der Untersuchungen wurde gelegt mit der Errichtung standardisierter Messaufbauten und Verfahren sowie Parameterauswahl für eine beschleunigte und reproduzierbare Darstellung des Kriechphänomens, wobei zunächst im Abgleich sichergestellt wurde, dass das beschleunigte Phänomen mit dem langsam über einen Zeitraum von Jahren erzeugten Phänomen deckungsgleich ist. Darauf aufbauend wurden innovative Untersuchungsmethoden entwickelt, um das Kriechverhalten zu charakterisieren und qualitativ sowie quantitativ zu analysieren. Hierzu wurde zunächst ein Aufbau und eine Messroutine entwickelt und eingeführt, um morphologische Veränderungen während des Kriechvorgangs im Rasterelektronenmikroskop nachzuverfolgen. Im Weiteren wurden Versuchsaufbauten für statische 3-Punkt-Biegeversuche in verschiedenen Lösungen realisiert und diese ergebnisabhängig optimiert. Hierdurch konnte der Einfluss der Löslichkeit von Gips in den entsprechenden Medien auf das Kriechverhalten untersuchen werden. Mittels Laserscanning-Mikroskop wurden wiederum diese Ergebnisse untermauert. Als vorherrschender Kriechmechanismus von Gips wurde damit das Abgleiten einzelner Gipskristalle bedingt durch einen Lösungs-Abscheide-Mechanismus an Orten hoher mechanischer Belastung identifiziert und bestätigt. N2 - In this work, a further and possibly decisive step could be taken towards clarifying the creep mechanism of gypsum and, based on this, ways and strategies could be identified in order to identify new anti-creep agents or to specifically improve existing anti-creep agents. The validity and practicability of the selection criteria for new anti-creep agents was demonstrated by several examples of selections of chemical moieties, to date unknown with respect to their activity as anti-creep agent for gypsum. The fundament of the investigations was laid with the establishment of standardised measurement setups and procedures as well as with the selection of parameters for an accelerated and reproducible representation of the creep phenomenon, whereby it was ensured that the accelerated creep is comparable to natural, slow creep which usually takes up to several years in gypsum materials. On this basis, innovative investigation methods were developed to characterise the creep behaviour and to analyse it qualitatively and quantitatively. Firstly, a setup and a measuring routine were developed and introduced to track morphological changes during the creep process via scanning electron microscopy. Secondly, test setups for static 3-point bending tests were realized in different solutions and optimized. This enabled the investigation of the correlation between the solubility of gypsum in different media and the resulting creep behaviour. These results were substantiated further by means of laser scanning microscopy. Using these methods, it was possible to identify and confirm the slippage of individual gypsum crystals due to a solution deposition mechanism at locations of high mechanical stress as the predominant creep mechanism of gypsum. The creep of gypsum is thus decisively determined by an increased humidity in the pores of gypsum, which results in an enlargement of the water layer in the space between the gypsum crystals in the polycrystalline structure. Thus, gypsum crystals can slide more easily against each other under load via the mechanism of the so-called "pressure solution creep". This mechanism could be confirmed by creep tests with different large gypsum crystals in the polycrystalline gypsum body. Thus, the creep velocity results primarily from the number and size of the contact points of the gypsum crystal as well as the solubility of the crystals at these interfaces in the pore liquid. Particulate, hydraulic and surface-active additives were tested to influence the creep behaviour of gypsum. In particular, the industrial anti-creep agent sodium trimetaphosphate (STMP) was investigated in detail. The mode of action of STMP as a state-of-the-art creeping agent was demonstrated by EDX mappings and transmission electron micrsocopy. The decisive influencing variables for anti-creep agents were identified to be the following ones: • A good solubility in water, which makes it possible to employ the anti-creep agent of choice in the mixing water used to form the gypsum material. • A moderate complex formation with calcium ions in the size range around log (KB) = 2.5. This moderate complex stability does significantly not hinder the crystal formation of the gypsum crystals on the one hand, but on the other hand enables a complex formation on the gypsum crystal surfaces. The surface coating which is thereby obtained, reduces the dissolution rate of gypsum in water. This is achieved by a surface coating on only certain crystal surfaces. In this thesis, the (100) and (001) planes were identified to be most preferentially complexed / coated with anti-creep agent. • A reinforcement of the gypsum matrix by "sticking" the crystals, as observed in-situ via transmission electron microscopy, also plays a role. This reinforcement may ultimately also be a reason for the increased dimensional stability. Based on these mechanisms which were identified for the state-of-the-art anti-creep agent STMP, novel chemical moieties as potential anti-creep agent candidates were selected. Surface-active additives such as poly(acrylic acid-co-maleic acid) (PAMA) were identified as a promising alternative to STMP. They are water-soluble, contain complexing centres for calcium ions with the same complexing constant as STMP and are toxicologically harmless. Ultimately, in the laboratory, these polymers, based on experiments with pure FGD gypsum, could well compete with the performance of STMP with regard to hinder creep of gypsum. KW - Rauchgasgips KW - Kriechen KW - Bassanit KW - Kriechverhalten Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-246503 ER - TY - THES A1 - Brockmann, Dorothea E. R. T1 - Gefüge-Simulationen an Nicht-Oxid-Keramiken: Korrelation zwischen Mikrostruktur und makroskopischen Eigenschaften T1 - Structure simulations on non-oxide ceramics: correlation between microstructure and macroscopic properties N2 - Die experimentelle Verbesserung der makroskopischen Eigenschaften (z. B. thermische oder mechanische Eigenschaften) von Keramiken ist aufgrund der zahlreichen erforderlichen Experimente zeitaufwändig und kostenintensiv. Simulationen hingegen können die Korrelation von Mikrostruktur und makroskopischen Eigenschaften nutzen, um die Eigenschaften von beliebigen Gefügekompositionen zu berechnen. In bisherigen Simulationen wurden meist stark vereinfachte Modelle herangezogen, welche die Mikrostruktur einer Keramik nur sehr grob widerspiegeln und deshalb keine zuverlässigen Ergebnisse liefern. In der vorliegenden Arbeit wird die Mikrostruktur-Eigenschafts-Korrelation der drei wichtigsten Nicht-Oxid-Keramiken untersucht. Dies sind Aluminiumnitrid (AlN), Siliciumnitrid (Si3N4) und Siliciumcarbid (SiC). Diese drei Keramiktypen vertreten die häufigsten Mikrostrukturtypen, welche bei Nicht-Oxid-Keramiken auftreten können. Zu jedem Keramiktyp liegen zwei verschiedene Proben vor. Alle drei untersuchten Keramiktypen sind zweiphasig. Die Hauptphase von AlN und Si3N4 besteht aus keramischen Körnern, die Nebenphase erstarrt während der Sinterung aus den zugesetzten Sinteradditiven. Die Restporosität von AlN und Si3N4 wird als vernachlässigbar angesehen und in den Simulationen nicht berücksichtigt. Bei den SiC-Proben handelt es sich um Keramiken mit bimodaler Korngröÿenverteilung. Durch Infiltration mit flüssigem Silicium wurden die Hohlräume zwischen den Körnern aufgefüllt, um porenfreie SiSiC-Proben zu erhalten. Anhand von Simulationen werden zunächst reale Mikrostrukturen in Anlehnung an vorliegende Vergleichsproben nachgebildet. Diese Modelle werden durch Abgleich mit rasterelektronenmikroskopischen 2D-Aufnahmen der Proben verifiziert. An den Modellen werden mit der Methode der Finite-Element-Simulation makroskopische Eigenschaften (Wärmeleitfähigkeit, Elastizitätsmodul und Poisson-Zahl) der Keramiken simuliert und mit experimentellen Messungen an den vorliegenden Proben abgeglichen. Der Vergleich der Mikrostruktur von den computergenerierten Gefügen und den vorliegenden Proben zeigt in der Mustererkennung durch das menschliche Auge und quantitativ in den Gefügeparametern eine gute Übereinstimmung. Für die makroskopischen Eigenschaften wird auf der Basis einer ausführlichen Literaturrecherche zu den Materialparametern der beteiligten Phasen eine gute Übereinstimmung zwischen den experimentell gemessenen und den simulierten Eigenschaften erreicht. Evtl. auftretende Abweichungen zwischen Experiment und Simulation können damit erklärt werden, dass die Proben Verunreinigungen enthalten, da aus der Literatur bekannt ist, dass Verunreinigungen eine Verschlechterung der Wärmeleitfähigkeit bewirken. Nachdem die Gültigkeit der Modelle verifiziert ist, wird der Einfluss von charakteristischen Mikrostrukturparametern und Phaseneigenschaften auf die Wärmeleitfähigkeit, den Elastizitätsmodul und die Poisson-Zahl der Keramiken untersucht. Hierzu werden die Mikrostrukturparameter von AlN und Si3N4 gezielt um die Parameter der vorliegenden Vergleichsproben variiert. Bei beiden Keramiktypen werden die Volumenanteile der beteiligten Phasen sowie die mittlere Sehnenlänge der keramischen Körner verändert. Bei den AlN-Keramiken wird zusätzlich der Dihedralwinkel variiert, welcher Auskunft über den Benetzungsgrad der Flüssigphase gibt; bei den Si3N4-Keramiken ist das Achsenverhältnis der langgezogenen Si3N4-Körner von Interesse und wird deshalb ebenfalls variiert. Es zeigt sich, dass die Aufteilung der Teilvolumina zwischen den zwei Phasen den größten Einfluss auf die Eigenschaften der Keramik hat, während die übrigen Mikrostrukturparameter nur eine untergeordnete Rolle spielen. Um die Qualität der Simulationen zu überprüfen, wird die Simulationsreihe an AlN mit unterschiedlicher Aufteilung der Volumina zwischen den beiden Phasen in Relation zu etablierten Modellen aus der Literatur (Mischungsregel und Modell nach Ondracek) gesetzt. Alle Simulationsergebnisse für die Wärmeleitfähigkeit und den Elastizitätsmodul liegen innerhalb der jeweils oberen und unteren Grenze beider Modelle. Es konnte also eine Verbesserung gegenüber den etablierten Modellen erzielt werden. An allen drei Keramiktypen wird der Einfluss der Materialeigenschaften der Haupt- und Nebenphase auf die makroskopischen Eigenschaften der Keramik untersucht. Hierfür werden die Wärmeleitfähigkeit, der Elastizitätsmodul und die Poisson-Zahl der Phasen getrennt voneinander über einen größeren Bereich variiert. Es stellt sich heraus, dass es vom Keramiktyp und dem Volumenanteil der Nebenphase abhängt, wie stark der Einfluss einer Komponenteneigenschaft auf die Eigenschaft der Keramik ist. Mit den im Rahmen dieser Arbeit durchgeführten Simulationen wird der Einfluss von Mikrostrukturparametern und Phaseneigenschaften berechnet. Auf der Grundlage dieser Simulationen können die Architektur des Gefüges simuliert und die Eigenschaften von Keramiken für individuelle Anwendungen berechnet werden. Dies ist die Basis für die Produktion von maßgeschneiderten Keramiken. Zudem können mit den validierten Mikrostrukturmodellen die Eigenschaften von unbekannten Mischphasen ermittelt werden, was experimentell oft nicht möglich ist. N2 - Experimental improvement of macroscopic properties (e. g. thermal or mechanical properties) of ceramics require countless experiments and are therefore costly in terms of time and money. However, simulations use the correlation of microstructure and macroscopic properties to calculate properties of any microstructure. Until now, simulations usually use oversimplified models, which only roughly reproduce a ceramics' microstructure and therefore do not give reasonable results. In the paper on hand, the microstructure-property-correlation of the three most important non-oxide-ceramics (AlN, Si3N4, SiC) is analysed. These three types of ceramic represent the most important types of microstructures, which exist for nonoxidic ceramics. For each type of ceramic, two different samples are examined. All three ceramic types used are two-phase-ceramics. The primary phase of AlN and Si3N4 is built of the ceramic grains and the secondary phase solidifies from the added sinter additives. The remaining porosity of AlN and Si3N4 is regarded to be negligible and is therefore not considered in the simulations. The SiC-samples are ceramics with a bimodal grain size distribution. The spaces in between the grains are filled by infiltration with liquid silicon to get Si-SiC-samples free of pores. At first, by employing simulations, microstructures are generated, which are close to the samples' microstructures. These models are verified by comparing them with two-dimensional scanning electron micrographs. Macroscopic properties (thermal conductivity, Young's modulus, Poisson's Ratio) of the ceramics are calculated by finite element simulations and then compared to experimental measurements on the samples. Analyzing the microstructures of the computer-generated models and the samples shows good agreement in the pattern matching as well as quantitatively in the microstructures parameters. Also for the macroscopic properties good comparison between measured and simulated properties was reached, based on an elaborate literature research on material parameters of all phases involved. Occurring discrepancies between experiment and simulations are assumed to be due to impurities in the sample. From literature it is known that impurities lead to a decline in thermal conductivity. As the models are validated, the influence of characteristic microstructure parameters and material properties of the phases on the thermal conductivity, Young's modulus and Poisson's ratio of ceramics are analysed. Therefore some microstructure parameters of the models of AlN and Si3N4 are deviated from the parameters of the samples. For both ceramic types the volume fractions of both phases and the average chord length of the grains are varied. At the AlN models, the dihedral angle is varied as well, which provides information about the wetting behaviour of the secondary phase; at the Si3N4 models, the aspect ratio of the elongated Si3N4 grains are of importance and hence analysed. It turns out that the volume fractions of the phases have the most significant influence on the ceramics' properties, whereas the other microstructure parameters are less important. To check the quality of the simulations, the simulation data of AlN with different volume fractions is compared to established models from literature ("rule of mixture" and model according to Ondracek). All results from the simulations are within the upper and lower bounds of both models. In comparison with these models, an improvement was achieved. For all three ceramic types, the influence of the material properties of the main and the secondary phase on the ceramics' properties is investigated. Therefore, the phases' thermal conductivity, Young's modulus and Poisson's ratio are separately from each other varied over a large range. It turns out that the influence of a component's property on the property of the ceramic depends on the ceramic type and the volume fraction of the secondary phase. On models of all three ceramic types, the influence of the components' material properties on the macroscopic properties of the ceramic is analysed. Based on these simulations, the architecture of microstructures can be simulated and properties of random ceramics for individual purposes can by calculated. By this, it is possible to produce customised ceramics. Additionally, with the validated microstructure models, the properties of unknown mixed phases can be calculated, which is usually not possible in experiments. KW - Aluminiumnitrid KW - Siliciumcarbid KW - Siliciumnitrid KW - Finite-Elemente-Methode KW - Wärmeleitfähigkeit KW - Mikrostrukturmodellierung KW - Elastizitätsmodul KW - inverse Simulation Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-157255 ER - TY - THES A1 - Nashed, Alexander T1 - Entwicklung spinnfähiger Precursorpolymere zur Herstellung nicht-oxidischer Keramikfasern T1 - Development of spinnable precursor polymers for the production of non-oxide ceramic fibers N2 - Ausgehend von chlorhaltigem Oligosilan, erhalten durch Disproportionierung der „Disilan-Fraktion“ der Müller-Rochow-Synthese, wurde mit verschiedenen Aminen dechloriert bzw. strukturell modifiziert. Die auf diese Weise in das Oligosilan eingeführten Baugruppen wurden spektroskopisch und durch Vergleich mit geeigneten Modellverbindungen identifiziert. Vernetzungsgrad und keramische Ausbeute der erzeugten Materialen wurden bestimmt. Mit Ammoniak oder einwertigen Aminen wie Methylamin werden Produkte erhalten, die sich nicht zu Keramikfasern verarbeiten lassen. Letzteres scheitert daran, dass entweder keine signifikante Molekulargewichtserhöhung des Oligosilans erreicht wird, oder führt dazu, dass das Oligomer vergelt und damit in Toluol unlöslich wird. Durch Umsetzung des Oligosilans mit zweiwertigen Aminen wie EDA oder TMDA als Vernetzungsreagenz gelang es, eine Syntheseroute zu entwickeln, die – anders als bei der am ISC etablierten Route – keinen thermischen Vernetzungsschritt erfordert, d.h. die gesamte Synthese findet bei Temperaturen ≤200 °C statt. Hierbei wird eine kontrollierbare Erhöhung des Molekulargewichts erreicht. Die Verwendung von TMDA hat gegenüber EDA den Vorteil, dass aufgrund des Ausbleibens von Ringbildung ein höher vernetztes Polymer erhalten wird. Darüber hinaus wurde gefunden, dass Grünfasern während der Pyrolyse durch radikalisch vernetzbare Gruppen (C=C-Doppelbindungen) im Polymer stabilisiert werden können. Diese Gruppen lassen sich entweder durch Dechlorierung mit Allylamin oder durch Umsetzung mit Vinyl-Grignard-Reagenzien einführen. Allylamin erwies sich hierbei als geeigneter, da es preiswerter und leichter handhabbar ist und außerdem – im Gegensatz zu Vinyl-Grignard-Reagenzien – eine vollständige Dechlorierung des Polymers gestattet. Alle Polymere wurden auf ihre Verarbeitbarkeit zu Grün- und anschließend zu Keramikfasern untersucht. Hierbei wurde gefunden, dass die im Hinblick auf die Eigenschaften der resultierenden Keramikfasern günstigste Rezeptur in der Umsetzung eines zuvor mit DMA vollständig dechlorierten Oligosilans mit 18,2 mol-% TMDA und 40 mol-% Allylamin (bezogen auf NMe2-Gruppen) besteht. Die aus diesem Polymer erhaltenen Keramikfasern zeigen die für noch nicht technisch ausgereifte, im Stadium der Entwicklung befindliche Fasern typischen Festigkeiten und entsprechen damit denjenigen, die auf der am ISC bereits etablierten Route erhältlich sind. Dies macht sie zu aussichtsreichen Kandidaten für die weitere Optimierung. N2 - Based on chlorine containing oligosilane which is synthesized via disproportionation of the “disilane fraction” of the Müller-Rochow synthesis, there have been dechlorinations respectively structural modifications with different amines. The structural components introduced into the oligosilane by this means were identified spectroscopically and by comparison with appropriate model compounds. The degree of crosslinking and the ceramic yield of the generated materials were detected. By the use of ammonia or primary amines like methylamine products are generated which cannot be converted to ceramic fibers. The latter fails because either no significant increase of the molecular weight of the oligosilane is obtained or the oligosilane gels and becomes insoluble in toluene. By the reaction of oligosilane with secondary amines like EDA or TMDA as a crosslinking reagent it succeeded to develop a synthesis route which – different from the route established at the ISC – doesn’t require any thermic crosslinking step what means that the whole synthesis takes place at temperatures ≤200°C. In this connection a controllable increase of the molecular weight is reached. The use of TMDA has the advantage over EDA that due to the absence of ring formation a higher cross-linked polymer is obtained. Furthermore it was found that green fibers can be stabilized during pyrolysis with radically curable groups (C=C double bonds) inside the polymer. These groups can be introduced either by dechlorination with allylamine or by reaction with vinyl Grignard reagents. Allylamine was proven to be more suitable because it is low-cost and easier to handle and besides – in comparison to vinyl Grignard reagents – it allows a complete dechlorination of the polymer. All polymers were analyzed concerning their processability to green and subsequent to ceramic fibers. Here it was found that the most favorable recipe with respect to the properties of the resulting ceramic fibers consists in the reaction of fully with DMA dechlorinated oligosilane with 18.2 mol-% TMDA and 40 mol-% allylamine (based on NMe2-groups). The ceramic fibers obtained from this polymer show typical stabilities as they are not yet technically mature and in the stage of development. For this reason they correlate with the ones which are already available by the established route at the ISC. This makes them to promising candidates for further optimization. KW - Keramikfaser KW - Polymerisation KW - Oligosilane KW - ceramic fibers KW - Precursorpolymer KW - SiC Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-138517 ER -