TY - JOUR A1 - Vogel, Patrick A1 - Rückert, Martin Andreas A1 - Friedrich, Bernhard A1 - Tietze, Rainer A1 - Lyer, Stefan A1 - Kampf, Thomas A1 - Hennig, Thomas A1 - Dölken, Lars A1 - Alexiou, Christoph A1 - Behr, Volker Christian T1 - Critical Offset Magnetic PArticle SpectroScopy for rapid and highly sensitive medical point-of-care diagnostics JF - Nature Communications N2 - Magnetic nanoparticles (MNPs) have been adapted for many applications, e.g., bioassays for the detection of biomarkers such as antibodies, by controlled engineering of specific surface properties. Specific measurement of such binding states is of high interest but currently limited to highly sensitive techniques such as ELISA or flow cytometry, which are relatively inflexible, difficult to handle, expensive and time-consuming. Here we report a method named COMPASS (Critical-Offset-Magnetic-Particle-SpectroScopy), which is based on a critical offset magnetic field, enabling sensitive detection to minimal changes in mobility of MNP ensembles, e.g., resulting from SARS-CoV-2 antibodies binding to the S antigen on the surface of functionalized MNPs. With a sensitivity of 0.33 fmole/50 µl (≙7 pM) for SARS-CoV-2-S1 antibodies, measured with a low-cost portable COMPASS device, the proposed technique is competitive with respect to sensitivity while providing flexibility, robustness, and a measurement time of seconds per sample. In addition, initial results with blood serum demonstrate high specificity. KW - biochemical assays KW - characterization and analytical techniques KW - magnetic properties and materials KW - nanoparticles Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-300893 VL - 13 ER - TY - JOUR A1 - Karak, Suvendu A1 - Stepanenko, Vladimir A1 - Addicoat, Matthew A. A1 - Keßler, Philipp A1 - Moser, Simon A1 - Beuerle, Florian A1 - Würthner, Frank T1 - A Covalent Organic Framework for Cooperative Water Oxidation JF - Journal of the American Chemical Society N2 - The future of water-derived hydrogen as the “sustainable energy source” straightaway bets on the success of the sluggish oxygen-generating half-reaction. The endeavor to emulate the natural photosystem II for efficient water oxidation has been extended across the spectrum of organic and inorganic combinations. However, the achievement has so far been restricted to homogeneous catalysts rather than their pristine heterogeneous forms. The poor structural understanding and control over the mechanistic pathway often impede the overall development. Herein, we have synthesized a highly crystalline covalent organic framework (COF) for chemical and photochemical water oxidation. The interpenetrated structure assures the catalyst stability, as the catalyst’s performance remains unaltered after several cycles. This COF exhibits the highest ever accomplished catalytic activity for such an organometallic crystalline solid-state material where the rate of oxygen evolution is as high as ∼26,000 μmol L\(^{–1}\) s\(^{–1}\) (second-order rate constant k ≈ 1650 μmol L s\(^{–1}\) g\(^{–2}\)). The catalyst also proves its exceptional activity (k ≈ 1600 μmol L s\(^{–1}\) g\(^{–2}\)) during light-driven water oxidation under very dilute conditions. The cooperative interaction between metal centers in the crystalline network offers 20–30-fold superior activity during chemical as well as photocatalytic water oxidation as compared to its amorphous polymeric counterpart. KW - water oxidation KW - sustainable energy source KW - covalent organic framework KW - catalyst KW - crystalline KW - catalysis KW - nanoparticles Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-287591 UR - https://pubs.acs.org/doi/10.1021/jacs.2c07282 SN - 0002-7863 VL - 144 IS - 38 ER - TY - JOUR A1 - Aido, Ahmed A1 - Zaitseva, Olena A1 - Wajant, Harald A1 - Buzgo, Matej A1 - Simaite, Aiva T1 - Anti-Fn14 antibody-conjugated nanoparticles display membrane TWEAK-like agonism JF - Pharmaceutics N2 - Conventional bivalent IgG antibodies targeting a subgroup of receptors of the TNF superfamily (TNFSF) including fibroblast growth factor-inducible 14 (anti-Fn14) typically display no or only very limited agonistic activity on their own and can only trigger receptor signaling by crosslinking or when bound to Fcγ receptors (FcγR). Both result in proximity of multiple antibody-bound TNFRSF receptor (TNFR) molecules, which enables engagement of TNFR-associated signaling pathways. Here, we have linked anti-Fn14 antibodies to gold nanoparticles to mimic the “activating” effect of plasma membrane-presented FcγR-anchored anti-Fn14 antibodies. We functionalized gold nanoparticles with poly-ethylene glycol (PEG) linkers and then coupled antibodies to the PEG surface of the nanoparticles. We found that Fn14 binding of the anti-Fn14 antibodies PDL192 and 5B6 is preserved upon attachment to the nanoparticles. More importantly, the gold nanoparticle-presented anti-Fn14 antibody molecules displayed strong agonistic activity. Our results suggest that conjugation of monoclonal anti-TNFR antibodies to gold nanoparticles can be exploited to uncover their latent agonism, e.g., for immunotherapeutic applications. KW - Fn14 KW - nanoparticles KW - surface modification KW - drug-delivery KW - anti-TNFRSF receptor (TNFR) antibodies Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-242710 SN - 1999-4923 VL - 13 IS - 7 ER - TY - JOUR A1 - Radeloff, Katrin A1 - Radeloff, Andreas A1 - Tirado, Mario Ramos A1 - Scherzad, Agmal A1 - Hagen, Rudolf A1 - Kleinsasser, Norbert H. A1 - Hackenberg, Stephan T1 - Long-Term Impact of Zinc Oxide Nanoparticles on Differentiation and Cytokine Secretion of Human Adipose-Derived Stromal Cells JF - Materials N2 - Zinc oxide nanoparticles (ZnO-NPs) are widely utilized, for example in manufacturing paints and in the cosmetic industry. In addition, there is raising interest in the application of NPs in stem cell research. However, cytotoxic, genotoxic and pro-inflammatory effects were shown for NPs. The aim of this study was to evaluate the impact of ZnO-NPs on cytokine secretion and differentiation properties of human adipose tissue-derived stromal cells (ASCs). Human ASCs were exposed to the subtoxic concentration of 0.2 mu g/mL ZnO-NPs for 24 h. After four weeks of cultivation, adipogenic and osteogenic differentiation procedures were performed. The multi-differentiation potential was confirmed histologically and using polymerase chain reaction (PCR). In addition, the gene expression of IL-6, IL-8, vascular endothelial growth factor (VEGF) and caspase 3 was analyzed. Over the course of four weeks after ZnO-NPs exposure, no significant differences were detected in the gene expression of IL-6, IL-8, VEGF and caspase 3 compared to non-exposed cells. The differentiation was also not affected by the ZnO-NPs. These findings underline the fact, that functionality of ASCs is likely to be unaffected by ZnO-NPs, despite a long-term disposition of NPs in the cells, supposing that the starting concentration was safely in the non-toxic range. This might provide important information for single-use nanomedical applications of ZnO-NPs. KW - zinc oxide KW - nanoparticles KW - toxicity KW - differentiation potential KW - human adipose-derived stromal cells KW - stem cells Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-224779 VL - 12 IS - 1823 ER - TY - JOUR A1 - Brachner, Andreas A1 - Fragouli, Despina A1 - Duarte, Iola F. A1 - Farias, Patricia M. A. A1 - Dembski, Sofia A1 - Ghosh, Manosij A1 - Barisic, Ivan A1 - Zdzieblo, Daniela A1 - Vanoirbeek, Jeroen A1 - Schwabl, Philipp A1 - Neuhaus, Winfried T1 - Assessment of human health risks posed by nano-and microplastics is currently not feasible JF - International Journal of Environmental Research and Public Health N2 - The exposure of humans to nano-and microplastic particles (NMPs) is an issue recognized as a potential health hazard by scientists, authorities, politics, non-governmental organizations and the general public. The concentration of NMPs in the environment is increasing concomitantly with global plastic production and the usage of plastic materials. NMPs are detectable in numerous aquatic organisms and also in human samples, therefore necessitating a risk assessment of NMPs for human health. So far, a comprehensive risk assessment of NMPs is hampered by limited availability of appropriate reference materials, analytical obstacles and a lack of definitions and standardized study designs. Most studies conducted so far used polystyrene (PS) spheres as a matter of availability, although this polymer type accounts for only about 7% of total plastic production. Differently sized particles, different concentration and incubation times, and various biological models have been used, yielding hardly comparable data sets. Crucial physico-chemical properties of NMPs such as surface (charge, polarity, chemical reactivity), supplemented additives and adsorbed chemicals have been widely excluded from studies, although in particular the surface of NMPs determines the interaction with cellular membranes. In this manuscript we give an overview about the critical parameters which should be considered when performing risk assessments of NMPs, including novel reference materials, taking into account surface modifications (e.g., reflecting weathering processes), and the possible role of NMPs as a substrate and/or carrier for (pathogenic) microbes. Moreover, we make suggestions for biological model systems to evaluate immediate toxicity, long-term effects and the potential of NMPs to cross biological barriers. We are convinced that standardized reference materials and experimental parameters along with technical innovations in (nano)-particle sampling and analytics are a prerequisite for the successful realization of conclusive human health risk assessments of NMPs. KW - nanoplastics KW - nanoparticles KW - microplastics KW - microparticles KW - human exposure KW - biological barriers KW - biofilm KW - microbe carrier KW - toxicity KW - neurotoxicity Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-219423 SN - 1660-4601 VL - 17 IS - 23 ER - TY - JOUR A1 - Radeloff, Katrin A1 - Radeloff, Andreas A1 - Ramos Tirado, Mario A1 - Scherzad, Agmal A1 - Hagen, Rudolf A1 - Kleinsasser, Norbert H. A1 - Hackenberg, Stephan T1 - Toxicity and functional impairment in human adipose tissue-derived stromal cells (hASCs) following long-term exposure to very small iron oxide particles (VSOPs) JF - Nanomaterials N2 - Magnetic nanoparticles (NPs), such as very small iron oxide NPs (VSOPs) can be used for targeted drug delivery, cancer treatment or tissue engineering. Another important field of application is the labelling of mesenchymal stem cells to allow in vivo tracking and visualization of transplanted cells using magnetic resonance imaging (MRI). For these NPs, however, various toxic effects, as well as functional impairment of the exposed cells, are described. The present study evaluates the influence of VSOPs on the multilineage differentiation ability and cytokine secretion of human adipose tissue derived stromal cells (hASCs) after long-term exposure. Human ASCs were labelled with VSOPs, and the efficacy of the labelling was documented over 4 weeks in vitro cultivation of the labelled cells. Unlabelled hASCs served as negative controls. Four weeks after labelling, adipogenic and osteogenic differentiation was histologically evaluated and quantified by polymerase chain reaction (PCR). Changes in gene expression of IL-6, IL-8, VEGF and caspase 3 were determined over 4 weeks. Four weeks after the labelling procedure, labelled and unlabelled hASCs did not differ in the gene expression of IL-6, IL-8, VEGF and caspase 3. Furthermore, the labelling procedure had no influence on the multidifferentiation ability of hASC. The percentage of labelled cells decreased during in vitro expansion over 4 weeks. Labelling with VSOPs and long-term intracellular disposition probably have no influence on the physiological functions of hASCs. This could be important for the future in vivo use of iron oxide NPs. KW - iron oxide nanoparticles KW - VSOP KW - nanoparticles KW - toxicity KW - differentiation potential KW - human adipose-derived stromal cells KW - stem cells KW - long-term exposure Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-203676 SN - 2079-4991 VL - 10 IS - 4 ER - TY - JOUR A1 - Ickrath, Pascal A1 - Wagner, Martin A1 - Scherzad, Agmal A1 - Gehrke, Thomas A1 - Burghartz, Marc A1 - Hagen, Rudolf A1 - Radeloff, Katrin A1 - Kleinsasser, Norbert A1 - Hackenberg, Stephan T1 - Time-Dependent Toxic and Genotoxic Effects of Zinc Oxide Nanoparticles after Long-Term and Repetitive Exposure to Human Mesenchymal Stem Cells JF - International Journal of Environmental Research and Public Health N2 - Zinc oxide nanoparticles (ZnO-NP) are widely spread in consumer products. Data about the toxicological characteristics of ZnO-NP is still under controversial discussion. The human skin is the most important organ concerning ZnO-NP exposure. Intact skin was demonstrated to be a sufficient barrier against NPs; however, defect skin may allow NP contact to proliferating cells. Within these cells, stem cells are the most important toxicological target for NPs. The aim of this study was to evaluate the genotoxic and cytotoxic effects of ZnO-NP at low-dose concentrations after long-term and repetitive exposure to human mesenchymal stem cells (hMSC). Cytotoxic effects of ZnO-NP were measured by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) assay. Furthermore, genotoxicity was evaluated by the comet assay. For long-term observation over 6 weeks, transmission electron microscopy (TEM) was applied. The results of the study indicated cytotoxic effects of ZnO-NP beginning at high concentrations of 50 μg/mL and genotoxic effects in hMSC exposed to 1 and 10 μg/mL ZnO-NP. Repetitive exposure enhanced cyto- but not genotoxicity. Intracellular NP accumulation was observed up to 6 weeks. The results suggest cytotoxic and genotoxic potential of ZnO-NP. Even low doses of ZnO-NP may induce toxic effects as a result of repetitive exposure and long-term cellular accumulation. This data should be considered before using ZnO-NP on damaged skin. KW - zinc oxide KW - ZnO KW - nanoparticles KW - cytotoxicity KW - toxicity KW - genotoxicity Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-169932 VL - 14 IS - 12 ER - TY - JOUR A1 - Han, Luyang A1 - Wiedwald, Ulf A1 - Biskupek, Johannes A1 - Fauth, Kai A1 - Kaiser, Ute A1 - Ziemann, Paul T1 - Nanoscaled alloy formation from self-assembled elemental Co nanoparticles on top of Pt films JF - Beilstein Journal of Nanotechnology N2 - The thermally activated formation of nanoscale CoPt alloys was investigated, after deposition of self-assembled Co nanoparticles on textured Pt(111) and epitaxial Pt(100) films on MgO(100) and SrTiO3(100) substrates, respectively. For this purpose, metallic Co nanoparticles (diameter 7 nm) were prepared with a spacing of 100 nm by deposition of precursor-loaded reverse micelles, subsequent plasma etching and reduction on flat Pt surfaces. The samples were then annealed at successively higher temperatures under a H2 atmosphere, and the resulting variations of their structure, morphology and magnetic properties were characterized. We observed pronounced differences in the diffusion and alloying of Co nanoparticles on Pt films with different orientations and microstructures. On textured Pt(111) films exhibiting grain sizes (20–30 nm) smaller than the particle spacing (100 nm), the formation of local nanoalloys at the surface is strongly suppressed and Co incorporation into the film via grain boundaries is favoured. In contrast, due to the absence of grain boundaries on high quality epitaxial Pt(100) films with micron-sized grains, local alloying at the film surface was established. Signatures of alloy formation were evident from magnetic investigations. Upon annealing to temperatures up to 380 °C, we found an increase both of the coercive field and of the Co orbital magnetic moment, indicating the formation of a CoPt phase with strongly increased magnetic anisotropy compared to pure Co. At higher temperatures, however, the Co atoms diffuse into a nearby surface region where Pt-rich compounds are formed, as shown by element-specific microscopy. KW - alloy KW - CoPt KW - HRTEM KW - nanoparticles KW - XMCD KW - Co KW - epitaxy KW - magnetometry KW - Pt Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-142869 VL - 2 ER - TY - THES A1 - Blömer, Steffen T1 - Synthese von modifizierten Eisenoxid-Nanopartikeln für die MR-Tomographie T1 - Synthesis of modified iron oxide nanoparticles for MRI N2 - In der vorliegenden Arbeit wurden magnetische Kolloide auf der Basis von Eisenoxid-Nanopartikeln hergestellt, die eine erhöhte Verweildauer im Blutstrom aufweisen sollten. Die Hüllmoleküle bestehen aus zwei Teilen: Direkt an den Phosphor gebunden eine hydrophobe Alkylkette aus vier bis zehn CH2-Einheiten, und daran anschließend eine Methoxy-terminierte Polyethylenglykol (PEG)-Kette. Die PEG-Kette sollte sowohl die Hydrophilie der fertigen Partikel als auch den nötigen Schutz gegen Phagozytose gewährleisten. Diese speziellen Phosphonsäuren wurden dann dazu verwendet, Magnetit-Nanopartikel stabil einzuhüllen. N2 - The present dissertation deals with the preparation of magnetic colloids on the basis of iron oxide nanoparticles exhibiting an extended lifetime in the bloodstream. The coating molecules were made up of two parts: A hydrophobic alkyl chain of four to ten CH2 groups, and a methoxy-terminated polyethyleneglycol (PEG) chain. The PEG chain was included to make the particles hydrophilic and to protect them from phagocytosis. These specially designed phosphonic acids were then used to coat magnetite nanoparticles. KW - Eisenoxide KW - Nanopartikel KW - NMR-Tomographie KW - Kontrastmittel KW - Polyethylenglykole KW - Magnetresonanztomographie KW - PEG KW - iron oxide KW - nanoparticles KW - MRI KW - contrast agent Y1 - 2011 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-66068 ER - TY - THES A1 - Niederdraenk, Franziska T1 - Ensemble-Modellierung von Röntgenbeugungsdaten zur Strukturbestimmung von Nanopartikeln T1 - Ensemble modeling of X-ray diffraction data for the geometric structure determination of nanoparticles N2 - Ziel dieser Arbeit war es, die geometrische Struktur von Nanopartikeln mittels Pulver-Röntgenbeugung und einem neuen Analyse-Verfahren, der Ensemble-Modellierung (EM), zu ermitteln. Die genaue Aufklärung der kristallinen Struktur ist ein Schlüssel für die Entwicklung exakter theoretischer Modelle und damit für ein besseres Verständnis der Nanoteilchen und deren Eigenschaften. Dabei fußt die Methode auf einem atomaren Modell und berechnet daraus das Beugungsbild der Teilchen. Neben der Auswertung verschiedener Proben sollte ebenso das Potential der Methode überprüft werden - auch im Vergleich zu Standardmethoden wie der Rietveld-Verfeinerung oder einer Einzellinien-Anpassung. Im Gegensatz zur EM beinhalten letztere kein explizites Nanoteilchenmodell. Insgesamt kamen drei typische Nanopartikel-Systeme zum Einsatz: Zunächst wurden fünf ZnO-Proben untersucht, die aufgrund ihrer verschiedenen Liganden deutlich unterschiedliche Partikelgrößen zeigten. Die präsentierten CdS-Nanoteilchen bildeten dagegen mit unter 100 Atomen bereits den Übergang zur Clusterphysik. Das letzte Kapitel stellte schließlich drei Proben mit deutlich komplexeren Core-Shell-Partikeln vor, welche aus einem CdSe-Kern und einer ZnS-Schale bestehen. Dabei konnten mit Hilfe der EM für alle Systeme sehr viel detailliertere Aussagen gemacht werden, als mit den Standardmethoden. Anhand der ersten vorgestellten ZnO-Probe wurde gezeigt, wie man sich bei der Auswertung mit der EM schrittweise dem besten Modell nähert, indem man, startend mit der Partikelform, anschließend weitere komplexe Merkmale implementiert. In dem ZnO-Kapitel wurde ersichtlich, dass die Liganden eine große Rolle spielen - nicht nur für die Größe der Nanopartikel, sondern auch für deren Qualität. Weiterhin wurde festgestellt, dass der Ligand TG beinahe defektfreie Nanoteilchen liefert, während die Stabilisatoren DACH und DMPDA den Einbau von Stapelfehlern begünstigen. In den jeweiligen Vergleichen mit der Rietveld- und Einzellinien-Anpassung fiel auf, dass diese Methoden für kleine Nanoteilchen Resultate liefern, die als deutlich weniger vertrauenswürdig einzustufen sind als jene, die mit der EM erhalten wurden. Der Grund sind die für kleine Teilchen nicht vernachlässigbaren Faktoren wie eine (anisotrope) Form, Oberflächeneffekte, Parameter-Verteilungen etc., welche nur mit der EM berücksichtigt werden können. Noch ungenauer fällt die Analyse per Absorptionsspektroskopie plus theoretischen Methoden aus. Die einzige CdS-Probe wies mit ca. 1.3 nm Durchmesser besonders kleine Nanoteilchen auf. Das zugehörige Beugungsbild zeigte daher nur noch sehr wenige Strukturen, was bereits die Bestimmung der Kristallstruktur erschwerte. Bei nur noch einigen gestapelten Schichten verloren auch die Stapelfehler ihre ursprüngliche Bedeutung. Die maßgebliche Frage bestand somit darin, ob man bei Kristalliten mit unter 100 Atomen noch von einer "normalen" Kristallstruktur sprechen kann, oder ob hier bereits andere Strukturformen vorliegen, z.B. ähnlich den C60-Molekülen. Da die EM solche Hohl-Strukturen ebenfalls simulieren kann, wäre der nächste Schritt, diese für sehr kleine Partikel im Vergleich zu den üblichen Kristallstrukturen zu testen. Bei den drei betrachteten Core-Shell-Proben zeigte die EM abermals ihre große Stärke, indem sie es ermöglichte, die deutlich komplexeren Teilchen realistisch zu simulieren. So war es möglich, die experimentellen Röntgenbeugungs-Daten hervorragend wiederzugeben, was mit keiner der Standardmethoden gelang. Hierfür war es nötig, neben dem CdSe-Kern eine zusätzliche ZnS-Schalenstruktur einzuführen. Zwar konnte bei den Proben mit der EM alleine nicht eindeutig festgestellt werden, welcher ZnS-Schalentypus vorliegt, es wurden jedoch diverse Anhaltspunkte gefunden, die für ein lokal-epitaktisches Wachstum auf dem CdSe-Kern sprechen. Für die Methode der EM selbst lässt sich in der Retrospektive folgendes fest halten: Sie ist den Standard-Techniken wie der Rietveld-Verfeinerung für sehr kleine Nanopartikel deutlich überlegen. Der Grund dafür sind die vielfältig modellierbaren Strukturen, welche Defekte, Oberflächeneffekte, Parameterverteilungen etc. beinhalten können. Ein weiterer großer Pluspunkt der EM gegenüber anderen Methoden besteht in der Möglichkeit, die immer populärer werdenden Core-Shell-Partikel mit vielfältigen Schalenarten zu simulieren, wobei hier auch noch weitere komplexere Optionen für Schalen, z.B. zweierlei Schalen (Core-Shell-Shell-Teilchen), vorstellbar sind. Die Tatsache, dass all diese Merkmale zudem intrinsisch in dem berechneten Beugungsbild enthalten sind, ist von besonderem Gewicht, da dies bedeutet, keine künstlichen Parameter einführen und diese interpretieren zu müssen. Solange eine gewisse Atomanzahl pro Partikel nicht überschritten wird, und v.a. bei defektbehafteten Nanoteilchen, stellt die EM somit die erste Wahl dar. N2 - The goal of this thesis was to determine the geometric structure of very small nanoparticles by means of powder x-ray diffraction and a novel analysis method called Ensemble Modeling (EM). The knowledge of the crystalline structure is a key feature to develop new theoretical models and thus to better understand the particles' properties. The analysis method itself is based on an atomic model of the particles, which is used to calculate the diffraction pattern via the Debye formula. Apart from the investigation of several nanoparticle samples, the capability of the new technique was tested - especially in comparison to commonly used standard methods like the Rietveld refinement or single-line fits. In contrast to the EM, these methods do not contain a real model of the particles. Altogether, three characteristic nanoparticle systems were used: First of all, five ZnO samples were investigated, which showed different particle sizes (2-15 nm) due to the use of different stabilizing molecules. In contrast, the CdS particles presented here had a diameter of only 1.3 nm, which is already at the transition to cluster physics. The last chapter introduced three samples of the more complex core-shell-nanoparticles, which, in this case, consisted of a CdSe core and a ZnS shell. By applying the EM as analysis method, all particle systems could be investigated in much more detail than with other analysis methods. The first ZnO sample served as an example to explain the stepwise procedure of the EM. After the particle shape was determined, more and more complex features were implemented in order to eventually arrive at the atomic model best reproducing the real particle ensemble. In case of the ZnO samples it was shown that the ligands play a significant role - not only for the size of the particles but also for their structural quality. A further finding due to the analysis with the EM is the high amount of stacking faults for particles stabilized with the ligands DACH or DMPDA, while TG favors a defect-free growth of ZnO nanoparticles. In comparison to the Rietveld method or to a single-line fit, the results for small nanoparticles given by the EM are much more reliable, since none of the other fitting methods can take features like the (anisotropic) particle shape, surface effects or parameter distributions into account. The same holds for a particles' size analysis via UV/Vis absorption spectroscopy together with theoretical models. The EM, in contrast, can account for all of these sophisticated structural features. The only CdS sample in this work contained extremely small particles of about 1.3 nm in diameter. The according diffraction pattern thus shows very broad reflections and little usable structure, thereby hindering a straight-forward analysis. Since the CdS particles consisted of only a few stacked layers, even the concept of stacking faults looses its meaning. The question arises, whether the term "crystal structure" is still appropriate for a particle with less than 100 Atoms. For instance, it would be possible that the particles form hollow structures similar to the C60 molecules. Since these structures can be simulated with the EM as well, this could be one next step to further analyse the XRD data of the CdS sample. The last chapter of this thesis introduced three samples of core-shell-nanoparticles, each with a CdSe core and a ZnS shell. Here again, the power of the EM method was demonstrated by forming a realistic model of these much complexer particles. The calculated diffraction patterns reproduced the experimental data very well - in contrast to all other analysis methods. The success of the EM was due to the implementation of an additional ZnS structure in the simulated model. Even if the shell type of this additional structure could not clearly be identified by XRD and our analysis, there is some strong evidence for a local epitaxy of the ZnS on the CdSe core. In conclusion, it was demonstrated that the EM method is far superior to any of the standard techniques for the diffraction pattern analysis of small nanoparticles. The particular strengths of the EM are the manifold structures, which can be simulated, together with defects, surface effects, parameter distributions etc. A further advantage over the other analysis methods is the possibility to form realistic core-shell-particles with a diversity of shell types. Even more complex shells are conceivable, e.g. a mixed shell or the double shell of the core-shell-shell-particles. All these features are intrinsically included in the models and thus in the diffraction patterns, i.e., no artificial parameters must be introduced and later be interpreted. As long as a certain amount of atoms per particle is not exceeded, and, especially for particles containing many defects, the EM introduced here should thus be preferred. KW - Nanopartikel KW - Röntgenstrukturanalyse KW - Ensemble-Modellierung KW - Core-shell Nanoteilchen KW - CdSe/ZnS Nanoteilchen KW - Strukturbestimmung KW - Röntgenbeugung KW - Zinkoxid KW - Cadmiumselenid KW - XRD KW - structure determination KW - nanoparticles KW - ensemble modeling Y1 - 2009 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-52218 ER -