TY - THES A1 - Langer, Fabian T1 - Wachstum und Charakterisierung von 1,0 eV GaInNAs-Halbleitern für die Anwendung in Mehrfachsolarzellen T1 - Growth and characterization of 1.0 eV GaInNAs-semiconductors for the application in multi-junction solar cells N2 - Im Rahmen dieser Arbeit wurden GaInP/GaAs/GaInNAs 3J-Mehrfachsolarzellen in einem MBE/MOVPE-Hybridprozess hergestellt und untersucht. Der verwendete Hybridprozess, bei dem nur die GaInNAs-Teilsolarzelle mittels MBE hergestellt wird, kombiniert diese beiden Technologien und setzt sie entsprechend ihrer jeweiligen Vorteile ein. Die gezeigten Ergebnisse bestätigen grundsätzlich die Machbarkeit des Hybridprozesses, denn eine Degradation des mittels MBE hergestellten GaInNAs-Materials durch die Atmosphäre im MOVPE-Reaktor konnte nicht festgestellt werden. Dieses Resultat wurde von im Hybridprozess hergestellten 3J-Mehrfachsolarzellen, die GaInNAs-Teilsolarzellen enthalten, bekräftigt. Die offene Klemmspannung einer gezeigten Solarzelle erreichte bereits 2,59 V (AM1.5d) bzw. 2,48 V (AM0) und liegt damit jeweils über einer als Referenz hergestellten 2J-Mehrfachsolarzelle ohne GaInNAs. Die mittlere interne Quanteneffizienz der enthaltenen GaInNAs-Teilsolarzelle liegt bei 79 %. Die Berechnungen auf Grundlage dieser Effizienz unter Beleuchtung mit AM1.5d und unter Beleuchtung mit AM0 zeigten, dass nicht die enthaltene GaInNAs-Teilsolarzelle Strom limitierend wirkt, sondern die mittels MOVPE gewachsene GaInP-Teilsolarzelle. Die experimentell bestimmte Kurzschlussstromdichte der hergestellten Mehrfachsolarzelle ist wegen dieser Limitierung etwas geringer als die der 2J-Referenzsolarzelle. Der MOVPE-Überwachsvorgang bietet zwar noch weiteres Verbesserungspotential, aber es ist naheliegend, dass der Anwachsvorgang auf dem MBE-Material soweit optimiert werden kann, dass die aufgewachsenen GaInP- und GaAs-Schichten frei von Degradation bleiben. Damit bietet der Hybridprozess perspektivisch das Potential günstigere Produktionskosten in der Epitaxie von Mehrfachsolarzellen mit verdünnten Nitriden zu erreichen als es ausschließlich mittels MBE möglich ist. Im Vorfeld zur Herstellung der 3J-Mehrfachsolarzellen wurden umfassende Optimierungsarbeiten des MBE-Prozesses zur Herstellung der GaInNAs-Teilsolarzelle durchgeführt. So wurde insbesondere festgestellt, dass das As/III-Verhältnis während dem Wachstum einen entscheidenden Einfluss auf die elektrisch aktive Dotierung des GaInNAs-Materials besitzt. Die elektrisch aktive Dotierung wiederum beeinflusst sehr stark die Ausdehnung der Raumladungszone in den als p-i-n-Struktur hergestellten GaInNAs-Solarzellen und hat damit einen direkten Einfluss auf deren Stromerzeugung. In der Tendenz zeigte sich eine Zunahme der Stromerzeugung der GaInNAs-Teilsolarzellen bei einer gleichzeitigen Abnahme ihrer offenen Klemmspannung, sobald das As/III-Verhältnis während des Wachstums reduziert wurde. Durch eine sehr exakte Kalibration des As/III-Verhältnisses konnte ein bestmöglicher Kompromiss zwischen offener Klemmspannung und Stromerzeugung gefunden werden. Eine gezeigte GaInNAs-Einfachsolarzelle erreichte eine mittlere interne Quanteneffizienz von 88 % und eine offene Klemmspannung von 341 mV (AM1.5d) bzw. 351 mV (AM0). Berechnungen auf Grundlage der Quanteneffizienz ergaben, dass diese Solarzelle integriert in eine 3J-Mehrfachsolarzelle unter dem Beleuchtungsspektrum AM1.5g eine Stromdichte von 14,2 mA/cm^2 und unter AM0 von 17,6 mA/cm^2 erzeugen würde. Diese Stromdichten sind so hoch, dass diese GaInNAs-Solarzelle die Stromproduktion der GaInP- und GaAs-Teilsolarzellen in einer gängigen Mehrfachsolarzelle erreicht und keine Ladungsträgerverluste auftreten würden. Aufgrund ihrer höheren offenen Klemmspannung gegenüber einer Ge-Teilsolarzelle bietet diese GaInNAs-Teilsolarzelle das Potential die Effizienz der Mehrfachsolarzelle zu steigern. Messungen der Dotierkonzentration in der GaInNAs-Schicht dieser Solarzelle ergaben extrem geringe Werte im Bereich von 1x10^14 1/cm^3 bis 1x10^15 1/cm^3 (p-Leitung). In Ergänzung zu den Optimierungen des As/III-Verhältnisses konnte gezeigt werden, dass sich ein Übergang von p- zu n-Leitung im GaInNAs mit der Verringerung des As/III-Verhältnisses erzeugen lässt. Nahe des Übergangsbereiches wurden sehr geringe Dotierungen erreicht, die sich durch eine hohe Stromproduktion aufgrund der Ausbildung einer extrem breiten Verarmungszone gezeigt haben. Durch eine reduzierte offene Klemmspannung der bei relativ geringen As/III-Verhältnissen hergestellten Solarzellen mit n-leitendem GaInNAs konnte auf das Vorhandensein von elektrisch aktiven Defekten geschlossen werden. Generell konnten die gemessenen elektrisch aktiven Dotierkonzentrationen im Bereich von üblicherweise 10^16 1/cm^3 mit hoher Wahrscheinlichkeit auf elektrisch aktive Kristalldefekte im GaInNAs zurückgeführt werden. Eine Kontamination des Materials mit Kohlenstoffatomen in dieser Größenordnung wurde ausgeschlossen. N2 - In scope of this work GaInP/GaAs/GaInNAs 3J multi-junction solar cells have been produced by a MBE/MOVPE hybrid process and were investigated. The applied hybrid process, which only produces the GaInNAs sub cell by means of MBE, combines both technologies and uses them according to their advantages. The shown results confirm the feasibility of the hybrid process in principle, because a degradation of the GaInNAs material grown by MBE could not be found. This result was reconfirmed by 3J multi-junction solar cells, which contain GaInNAs sub cells. The open circuit voltage of one shown solar cell already reached 2.59 V (AM1.5d) and 2.48 V (AM0), respecitvely and outperformed in terms of voltage a produced 2J multi-junction solar cell without GaInNAs. The averaged internal quantum efficiency of the included GaInNAs sub cell reached 79 \%. The calculations based on this efficiency under illumantion with AM1.5d and under illumination with AM0 showed that not the included GaInNAs sub cell is limiting the current but the by means of MOVPE grown GaInP sub cell. The short current density under experimental conditions is somewhat lower than the one of the 2J reference solar cell due to this limitation. The MOVPE overgrowth indeed offers further potential for optimization, however, it is plausible that the initial growth procedure running on the MBE material can be optimized far enough to the point that the overgrown GaInP and GaAs layer remain degradation free. Thereby, the hybrid process offers perspectively the potential to reach lower production costs in the epitaxy of multi-junction solar cells including diluted nitrides as it is possible with the MBE method only. \newline Previous to the production of the 3J multi-junction solar cells comprehensive optimizations of the MBE process to produce the GaInNAs sub cell have been performed. First and foremost it was found that the As/III ratio during the growth has a critical influence on the electrical active doping of the GaInNAs material. However, the electrical active doping affects the extension of the depletion layer in the as p-i-n structure produced GaInNAs solar cells very strongly, which is directly related to their current generation. In general it was found that the increase of the current generation of the GaInNAs sub cell comes along with a decrease of its open circuit voltage as soon as the As/III ratio during the growth was lowered. Due to a very precise calibration of the As/III ratio a best possible compromise between the open circuit voltage and the current generation was found. A shown GaInNAs single-junction solar cell reached an averaged internal quantum efficiency of 88 \% and an open circuit voltage of 341 mV (AM1.5d) and 351 mV (AM0), respectively. Calculations based on the quantum efficiency showed that this solar cell integrated in a 3J multi-junction solar cell would produce a current density of 14.2 mA/cm$^{2}$ under the illumination spectrum AM1.5g and a current density of 17.6 mA/cm$^{2}$ under AM0. With such high current densities the GaInNAs solar cell reaches the current generation of the GaInP and GaAs sub cells in a current multi-junction solar cell and no charge carrier loss would occur. Due to its increased open circuit voltage, compared to a Ge sub cell, this GaInNAs sub cell indeed offers the potential to increase the efficiency of the multi-junction solar cell. Doping concentration measurements of the GaInNAs layer showed extremly low doping densities in the range between 1x10$^{14}$ 1/cm$^{3}$ and 1x10$^{15}$ 1/cm$^{3}$ (p-conductivity). In addition to the optimization of the As/III ratio we were able to show that a transition of p- to n-type conductivity of the GaInNAs material by reducing the As/III ratio can be induced. Close to the transition region a very low doping was achieved indicated by a high current generation due to the formation of an extreme broad depletion zone. Finding that the open circuit voltage of solar cells with n-type GaInNAs produced with relatively low As/III ratios is reduced, proved the existance of electrical active defects. So we can state, that the measured electrical active doping concentration in the range of typically 1x10$^{16}$ 1/cm$^{3}$ can be traced back to electrical active crystal defects in the GaInNAs layers with high probability. A contamination of the material with carbon atoms in this range was excluded. \newline KW - Mehrfach-Solarzelle KW - Molekularstrahlepitaxie KW - dilute nitride KW - GaInNAs Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-200881 ER - TY - THES A1 - Bisping, Dirk T1 - Wachstum und Charakterisierung von GaInNAs-basierenden Halbleiterstrukturen für Laseranwendungen in der optischen Telekommunikation T1 - Growth and characterization of GaInNAs-based semiconductor structures for laser applications in optical communication N2 - Im Rahmen dieser Arbeit wurden mit Molekularstrahlepitaxie GaInNAs-Strukturen für mögliche Anwendungen in der Telekommunikation als GaAs-basierende Alternative für herkömmliche Laser auf InP-Substrat hergestellt und untersucht. Zunächst wurden durch Optimierung der Substrattemperaturmessung und RF-Plasmaquelle die Voraussetzungen für gutes GaInNAs-Wachstum geschaffen. Thermisches Ausheilen ist essentiell, um eine gute optische Qualität von GaInNAs-Strukturen zu erzielen. Man beobachtet einen signifikanten Einfluss von Ausheildauer und -temperatur. Exzessives Ausheilen bei zu hohen Temperaturen bzw. zu langen Zeiten führt, neben einer ebenso unerwünschten Blauverschiebung der Emission, wiederum zu einer Degradation der optischen Qualität, die sich in einer deutlichen Reduktion der Photolumineszenz(PL)-Intensität äußert. GaInNAs-Quantenfilm(QF)-Laser mit Emission um 1240 nm mit möglicher Anwendung als Pumplaser für Ramanverstärker wurden hergestellt und charakterisiert. Durch eine Optimierung des in-situ-Ausheilens dieser Laserstrukturen konnten Laser mit sehr niedrigen Schwellenstromdichten von deutlich unter 200 A/cm^2 hergestellt werden. Für eine möglichst hohe Ausgangsleistung wurde der Wirkungsgrad der Bauteile durch eine Optimierung der internen Verluste erhöht. Eine Reduktion der internen Verluste konnte durch eine Anpassung des Dotierprofils und die Verwendung von sogenannten Large-Optical-Cavities (LOCs) erreicht werden. Mit Hilfe des LOC-Designs konnten sehr niedrige interne Verluste von nur 0,5 1/cm bei einer internen Quanteneffizienz von nahezu 80 % erreicht werden. Mit optimierten Strukturen wurde stabiler Dauerstrichbetrieb bei Ausgangsleistungen von mehreren Watt über 1000~h ohne sichtbare Degradation demonstriert. Mit auf dem LOC-Design basierenden Lasern konnte schließlich eine sehr hohe Ausgangsleistung von ca. 9 W gezeigt werden. Anschließend wurden Untersuchungen zu Quantenpunkten (QPen) im Materialsystem GaInNAs vorgestellt. Mit steigendem Stickstoffgehalt beobachtet man eine Rotverschiebung der Emission bis auf 1,43 µm, allerdings gleichzeitig eine deutliche Degradation der optischen Qualität. Eine Untersuchung der QP-Morphologie ergibt eine Reduktion der Homogenität der QP-Größenverteilung, die sich im Auftreten zweier unterschiedlich großer QP-Ensembles äußert. Um diese Degradation der QPe zu vermeiden, wurde weiterhin auf den N-Einbau in den QPen verzichtet. Wider Erwarten führt der Verzicht auf N in den QPen nicht zu einer Blauverschiebung der Emission. Dieses Resultat konnte auf die veränderte QP-Morphologie zurückgeführt werden. Durch eine Erhöhung des N-Gehaltes im die QP überwachsenden QF wurde eine weitere deutliche Rotverschiebung der Emission erreicht. So konnte PL-Emission bei Raumtemperatur mit einem Emissionsmaximum bei 1600 nm demonstriert werden. Weiterhin wurden GaInNAs-QF-Strukturen für Laser im Wellenlängenbereich um 1550 nm untersucht. Da das Wachstum hier auf Grund des deutlich höheren, notwendigen N-Gehaltes wesentlich schwieriger wird, erfolgte zunächst eine detaillierte Untersuchung der wesentlichen Wachstumsparameter. Hierbei ist es essentiell, auch das Ausheilverhalten der jeweiligen Strukturen genau zu betrachten. Bei einer Untersuchung des Einflusses der Wachstumstemperatur auf GaInNAs-Teststrukturen wurden signifikante Unterschiede auch bei nur sehr geringen Änderungen in der Substrattemperatur von nur 10 °C festgestellt. Die beobachteten Effekte wurden vor dem Hintergrund des Modells der QP-ähnlichen Emitter diskutiert. Eine Variation des Arsen-Flusses zeigte einen deutlichen Einfluss auf die PL-Emission und vor allem auf das Ausheilverhalten. Das Ausheilverhalten lässt sich durch eine Anpassung des Arsen-Flusses maßgeschneidert anpassen. Während dem Überwachsen der aktiven Schicht mit Mantel- und Kontaktschicht kann es bereits zu einem Überausheilen der Strukturen kommen. Es wurden Laser mit niedrigen Schwellenstromdichten um 1 kA/cm^2 bis zu einer Wellenlänge von 1500 nm hergestellt. Für höhere Wellenlängen steigt die Schwellenstromdichte in den Bereich von 2 bis 3 kA/cm^2. Maximal wurde Laseremission bei über 1600 nm erreicht. Bei der Untersuchung der bei 1600 nm emittierenden Laserdioden wurde eine Verbreiterung der Laseremission zur hochenergetischen Seite auf bis zu 150 nm Bandbreite bei steigendem Betriebsstrom beobachtet. Dieser Effekt kann mit Hilfe des Modells der QP-ähnlichen Emitter verstanden werden. Unter Ausnutzung dieses Effekts wurden auf dem selben epitaktischen Material monomodige Distributed-Feedback(DFB)-Laser über einen Wellenlängenbereich von ca. 1500 nm bis 1600 nm gezeigt. Auf Basis der zuvor vorgestellten langwelligen Laserstrukturen mit niedrigen Schwellenstromdichten wurde erstmals Dauerstrichbetrieb von monomodigen DFB-Lasern im Bereich um 1500 nm und von multimodigen Stegwellenleiter-Lasern über 1500 nm im Materialsystems GaInNAs gezeigt. N2 - In this work, GaInNAs structures for telecom application based on GaAs in contrast to common lasers based on InP substrates have been grown by molecular beam epitaxy and subsequently characterized. First, optimizations of substrate temperature measurement and RF plasma source were incorporated to allow high quality GaInNAs growth. Thermal annealing is crucial to achieve high optical quality of GaInNAs structures. After a discussion of the microscopic processes during annealing, the influence of annealing parameters was examined. Excessive annealing with too high temperatures or too long times can, besides the typical blue-shift of the emission, also result in a decrease of the optical quality leading to a considerable reduction of the photoluminescence intensity. Laser diodes based on GaInNAs quantum wells emitting around 1240nm have been grown and characterized for a potential application as pump sources for Raman amplifiers. Using an optimization of the in-situ annealing during growth of these structures, laser diodes with very low threshold current densities well below 200 A/cm^2 have been realized. To achieve maximum output powers, the wallplug efficiencies of these devices have been increased by reducing the internal losses. Low internal losses have been achieved using an optimized doping profile or large optical cavities (LOCs). Using a LOC, very low internal losses of only 0.5 1/cm together with a high internal quantum efficiency of almost 80 % have been achieved. Stable performance for 1.000 h without degradation under continuous-wave operation was achieved. Using lasers with a LOC design, high maximum output powers of about 9 W have been demonstrated in continuous-wave operation. Afterwards, studies concerning quantum dots based on the GaInNAs material system have been shown. Increasing N-content leads to a redshift of the emissions wavelength up to 1.43 µm, but accompanied by a significant reduction of the optical quality. An examination of the quantum dot morphology also reveals a reduction in homogeneity of the quantum dot size distribution resulting in the occurence of quantum dot ensembles with two different sizes. To avoid this degradation of the quantum dots, N was not incorporated in the quantum dots, but only in the quantum well on top of the quantum dots. Unlike expectations, this doesn't involve a blueshift of the emission wavelength. This result could be explained by the different quantum dot morphology. By increasing the N-content in the quantum well the emission wavelength at room temperature was redshifted to 1600 nm. In addition, GaInNAs quantum well structures for laser diodes in the wavelength range around 1550 nm have been examined. Due to the more difficult growth resulting from the necessary higher N-content, a detailed examination of the growth parameters was required. Doing that, it is obligatory to take the annealing behaviour into account. A study of the influence of the substrate temperature showed a significant influence of very small differences in the range of 10 °C. Results have been discussed based on the modell of quantum dot like emitters. A variation of the arsenic flux during growth showed strong impact on photoluminescence emission and particularly annealing behaviour. The annealing behaviour can be tailored by changing the arsenic flux. Overgrowth of the quantum well with cladding and contact layers in complete laser stuctures can already result in over-annealing of the quantum well. It was possible to realize laser diodes with low threshold current densities in the range of 1 kA/cm^2 with emission wavelengths up to 1500 nm. For longer wavelengths, threshold current densities increase into the range of 2 to 3 kA/cm^2. The longest laser emission wavelength achieved was slightly above 1600 nm. Detailed examination of laser diodes emitting at 1600 nm revealed a huge broadening of the laser emission to higher energies resulting in an emission bandwidth of up to 150 nm under increasing drive current. This effect is explained using the model of quantum dot like emitters. Making use of this effect, single mode emitting distributed feedback lasers with emission wavelengths covering the whole wavelength range from 1500 to 1600 nm have been demonstrated. Based on the described long-wavelength laser diodes with low threshold current densities, continuous-wave operation of single-mode distributed feedback laser near 1500 nm and multimode ridge-waveguide lasers above 1500 nm have been shown for the first time using the GaInNAs material system. KW - Halbleiterlaser KW - Drei-Fünf-Halbleiter KW - Optoelektronik KW - verdünnte Nitride KW - Dilute Nitrides KW - Galliumarsenid KW - Molekularstrahlepitaxie KW - Telekommunikation KW - Hochleistungslaser KW - Dauerstrichbetrieb KW - Nitride Y1 - 2010 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-77538 ER - TY - THES A1 - Lermer, Matthias T1 - Wachstum und Charakterisierung von Quantenpunkt-Mikrotürmchen mit adiabatischer Modenanpassung T1 - Growth and characterisation of quantum dot - micropillars with adiabatic mode transission N2 - Verschiedene Konzepte zur Realisierung einer geeigneten Umgebung für Licht- Materie-Wechselwirkung konkurrieren um Anerkennung und eine ständige Optimierung der Systemparameter findet statt. Das Konzept von Mikrotürmchen scheint prädestiniert, da es viele anwendungsfreundliche Eigenschaften in sich vereint. Allerdings stellt die drastische Abnahme des Q Faktors für kleiner werdende Durchmesser d einen wesentlichen Limitierungsfaktor dieser Strukturen dar. Für viele Anwendungen resultiert daraus ein Kompromiss aus hohem Q Faktor und kleinem Modenvolumen der Strukturen, wodurch das volle Potential des Resonatorsystems nicht ausgeschöpft werden kann. Ziel dieser Arbeit war es, die drastische Abnahme des Q Faktors von Mikrotürmchen mit Durchmessern um 1μm aufzuheben und dadurch Resonatoren mit d < 1μm für ausgeprägte Licht-Materie-Wechselwirkung herzustellen. Dazu wurde erstmalig beabsichtigt eine Modenanpassung in Mikrotürmchen vorgenommen. Mittels Molekularstrahlepitaxie konnte eine Übergangsregion, bestehend aus drei Segmenten, in diese Strukturen implementiert und so ein adiabatischer Modenübergang zwischen der aktiven Mittelschicht und den Spiegelbereichen vorgenommen werden. Der positive Einfluss dadurch ergab sich in einer signifikanten Verbesserung des gemessenen Q Faktors für Durchmesser unter 1μm. Für d = 0.85μm konnte ein Q Faktor von 14 400 bestimmt werden. Dies stellt damit den höchsten je gemessenen Wert für Mikrotürmchen im Submikrometerbereich dar. Dadurch wird ein Bereich mit Modenvolumina < 3 kubischen Wellenlängen erschlossen und ausgeprägte Wechselwirkungseffekte im Mikrotürmchensystem sind zu erwarten. Starke Quantenpunkt-Licht-Kopplung konnte in diesen Strukturen nachgewiesen werden. Die höchste Vakuum-Rabiaufspaltung betrug 85μeV und die Visibilität wurde zu 0.41 bestimmt. Im Zuge der weiteren Optimierung der Systemparameter für die starke Kopplung wurde ein ex-situ Ausheilschritt auf die verwendete Quantenpunktsorte angewendet. In magnetooptischen Untersuchungen konnte damit eine Verdopplung der mittleren Oszillatorstärke auf einen Wert von 12 abgeschätzt werden. Weiter konnte in adiabatischen Mikrotürmchen über einen großen Durchmesserbereich von 2.25 bis 0.95μm eindeutiger Laserbetrieb des Quantenpunktensembles nachgewiesen werden. Dabei konnte eine kontinuierliche Reduzierung der Laserschwelle von über zwei Größenordnungen für kleiner werdende Durchmesser beobachtet werden. Für Durchmesser � < 1.6μm betrug der Beta-Faktor der Mikrolaser in etwa 0.5. Sie zeigten damit beinahe schwellenloses Verhalten. Zuletzt wurde der elektrische Betrieb von adiabatischen Mikrotürmchen gezeigt. Dafür wurde eine dotierte Struktur mit adiabatischem Design hergestellt. Im Vergleich zur undotierten Struktur fielen die gemessenen Q Faktoren in etwa um 5 000 geringer aus. Die spektralen Eigenschaften sowohl des Resonators als auch einzelner Quantenpunktlinien zeigten vernachlässigbare Abhängigkeit der Anregungsart (optisch oder elektrisch) und zeugen von einem erfolgreichen Konzept zum elektrischen Betrieb der Bauteile. Zeitaufgelöste Messungen erlaubten die Beobachtung von interessanten Dynamiken der Rekombination von Ladungsträgern in den Proben. Als Ursache dafür wurde ein hohes intrinsisches Feld, welches auf Grund des Designs der Schichtstruktur entsteht, identifiziert. Weiter zeigte sich, dass sich das interne Feld durch Anregungsart und extern angelegte Spannungen manipulieren lässt. N2 - Various concepts for the realization of a proper environment for interaction of light and matter compete for recognition and a continous optimizing process takes place. The concept of micropillars seems to be predestinated as it unifies many helpful properties for daily use applications. To this day the drastic decrease of the Q factor for smaller diameters d has been a fundamental reason for the limitation of these structures. For many applications a trade-off between high Q factor and small mode volume has been neccessary, so that the full potential of the resonator system has not been exploited totally. The objective of this work was to compensate for the drastic decrease of the Q factor of micropillars with diameters around 1μm and to fabricate resonators with d < 1μm for pronounced interaction of light and matter. For this purpose for the first time an intended mode engineering has been exploited in micropillars. By means of molecular beam epitaxy an intersection region, consisting of three segments, has been implemented in these structures and so an adiabatic transition of the mode between the active midsection and the mirrorparts has been achieved. The positive influence has been proven by a significant improvement of the measured Q factor for diameters below 1μm. For d = 0.85μm a Q factor of 14 400 has been detected. This is the highest Q factor ever measured for microilllars in the submicron regime. By that a regime with mode volumes < 3 cubic wavelengths gets accessible and pronounced effects of interaction in the system of micropillars are expected. In these structures strong quantum dot - light coupling has been shown. The largest vacuum- Rabisplitting has been 85μeV and the visibility has been determined to 0.41. In the course of further optimization of the system parameters for the regime of strong coupling an ex-situ annealing step has been adopted to the used type of quantum dots. Magnetooptical analysis has shown a doubling of the oscillator strength and allowed an estimation for the value to 12. Furthermore in adiabatic micropillars, over a vast diameter range from 2.25 to 0.95μm, clear evidence for lasing of the quantum dot ensemble has been shown. Simultanously a continous decrease of the lasing threshold by more than two orders of magnitude for small diameters has been observed. For Diameters < 1.6μm the Beta-factor of the microlasers has been determined to be around 0.5. Therefore they showed almost thresholdless behavior. Finally electrical operation of adiabatic micropillars has been shown. For that a doped structure with the adiabatic design has been fabricated. In comparison with the undoped structure the measured Q factors drop to values around 5 000. The spectral properties of both the resonator and single quantum dot lines have shown negligible dependence on the form of excitation (optical or electrical), indicating that a successful concept for the electrical excitation of the devices has been established. Time resolved measurments have allowed to observe interesting dynamics of the recombination of charge carriers. We have identified the large intrinsic field, which arises because of the design of the layer structure, being the origin for this. Furthermore we have shown, that the internal field can be manipulated by the excitation scheme and the external applied voltage. KW - Molekularstrahlepitaxie KW - Quantenpunkt KW - Adiabatische Modenanpassung KW - adiabatic modetransission KW - Licht Materie Wechselwirkung KW - light matter coupling KW - Optoelektronik KW - Lithografie KW - Spektroskopie Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-127438 ER - TY - THES A1 - Then, Patrick T1 - Waveguide-based single molecule detection in flow T1 - Wellenleiter-basierte Einzelmoleküldetektion in Strömungen N2 - In this work fluorescence-based single molecule detection at low concetration is investigated, with an emphasis on the usage of active transport and waveguides. Active transport allows to overcome the limits of diffusion-based systems in terms of the lowest detectable threshold of concentration. The effect of flow in single molecule experiments is investigated and a theoretical model is derived for laminar flow. Waveguides on the other hand promise compact detection schemes and show great potential for their possible integration into lab-on-a-chip applications. Their properties in single molecule experiments are analyzed with help of a method based on the reciprocity theorem of electromagnetic theory. N2 - Diese Arbeit untersucht fluoreszenzbasierte Einzelmoleküldetektion bei niedrigen Konzentrationen, mit einem Fokus auf den Einsatz von aktivem Transport und Wellenleitern. Aktiver Transport ermöglicht es, Limitierungen von diffusionsbasierten Systemen im Hinblick auf die niedrigste erreichbare Konzentration zu überwinden. Der Einfluss von Strömungen auf Einzelmolekülexperimente wird untersucht und ein theoretisches Modell für laminare Strömungen hergeleitet. Wellenleiter hingegen versprechen kompakte Detektorsysteme und zeigen beträchtliches Potential für eine mögliche Integration in lab-on-a-chip Anwendungen. Ihre Eigenschaften in Einzelmolekülexperimenten werden mithilfe einer auf dem Reziprozitätstheorem aus der elektromagnetischen Theorie basierenden Methode analysiert. KW - Optik KW - physics KW - optics KW - waveguides Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-140548 ER - TY - THES A1 - Jung, Johannes T1 - Wechselwirkungen zwischen Kantenzuständen auf dem topologisch kristallinen Isolator Pb\(_{1-x}\)Sn\(_x\)Se T1 - Interactions between edge states on the topologically crystalline insulator Pb\(_{1-x}\)Sn\(_x\)Se N2 - Einerseits besteht die einfachste Möglichkeit zum Ladungs- und Informationstransport zwischen zwei Punkten in deren direkter Verbindung durch eindimensionale Kanäle. Andererseits besitzen topologische Materialien exotische und äußerst vorteilhafte Eigenschaften, weshalb es nahe liegt, dass schon bald neue Anwendungen aus ihnen realisiert werden. Wenn diese beiden Entwicklungen zusammenkommen, dann ist ein grundlegendes Verständnis von Quanteninterferenz oder Hybridisierungseffekten in eindimensionalen, topologischen Kanälen von fundamentaler Wichtigkeit. Deshalb werden in der vorliegenden Arbeit Wechselwirkungen von eindimensionalen, topologisch geschützten Kantenzuständen, die an ungeradzahligen Stufenkanten auf der (001)–Oberfläche von Pb1−xSnxSe auftreten, untersucht. Aufgrund der lateralen Lokalisierung auf wenige Nanometer um eine Stufenkante herum und der Notwendigkeit zwischen gerad- und ungeradzahligen Stufenkantenhöhen zu unterscheiden, bieten sich die Rastertunnelmikroskopie und -spektroskopie als Methoden an. Die neu entdeckten Kopplungs- bzw. Wechselwirkungseffekte zwischen benachbarten Kantenzuständen treten auf, sobald der Stufe zu Stufe Abstand einen kritischen Wert von dkri ≈ 25nm unterschreitet. Dieses Kriterium kann durch verschiedene räumliche Anordnungen von Stufenkanten erfüllt werden. Infolgedessen werden sich kreuzende, parallel verlaufende und zusammenlaufende Stufenkanten genauer untersucht. Bei letzteren verändert sich entlang der Struktur kontinuierlich der Abstand und damit die Kopplungsstärke zwischen den beiden Randkanälen. Infolgedessen wurden drei Koppelungsregime identifiziert. (I) Ausgehend von einer schwachen Wechselwirkung zeigt der für die Kantenzustände charakteristische Peak im Spektrum zunächst eine Verbreiterung und Verminderung der Intensität. (II) Mit weiter zunehmender Wechselwirkung beginnt sich der Zustand in zwei Peaks aufzuspalten, sodass ab dkri ≈ 15nm an beiden Stufenkanten durchgehen eine Doppelpeak zu beobachten ist . Mit weiter abnehmendem Abstand erreicht die Aufspaltung Werte von einigen 10 meV, während sich die Intensität weiter reduziert. (III) Sobald zwei Stufenkanten weniger als etwa 5nm voneinander getrennt sind, konvergieren aufgrund der schwindenden Intensität und des sinkenden energetischen Abstands der beiden Peaks zu den van Hove Singularitäten die Spektren an den Stufenkanten gegen das Spektrum über einer Terrasse. i Die Aufspaltung verläuft in den Bereichen I und II asymmetrisch, d. h. ein Peak verbleibt ungefähr bei der Ausgangsenergie, während der andere mit zunehmender Kopplung immer weiter weg schiebt. Bezüglich der Asymmetrie kann kein Unterschied festgestellt werden, ob die zusammenlaufenden Stufenkanten eine Insel oder Fehlstelleninsel bilden oder ob die Stufenkanten sogar gänzlich parallel verlaufen. Es zeigt sich keine Präferenz, ob zunächst der niederenergetische oder der hochenergetische Peak schiebt. Erst im Regime starker Kopplung (III) kann beobachtet werden, dass beide Peaks die Ausgangsenergie deutlich verlassen. Im Gegensatz dazu kann bei sich kreuzenden Stufen ein erheblicher Einfluss der Geometrie, in Form des eingeschlossenen Winkels, auf das Spektrum beobachtet werden. Unabhängig vom Winkel existiert am Kreuzungspunkt selbst kein Kantenzustand mehr. Die Zustände an den vier Stufen beginnen, abhängig vom Winkel, etwa 10-15nm vor dem Kreuzungspunkt abzuklingen. Überraschenderweise zeigt sich dabei, dass im Fall rechtwinkliger Stufen gar keine Aufspaltung zu beobachten ist, während bei allen anderen Winkeln ein Doppelpeak festgestellt werden kann. Diese Entdeckung deutet auf Orthogonalität bezüglich einer Quantenzahl bei den beteiligten Kantenzustände hin. Neben einer nur theoretisch vorhergesagten Spinpolarisation kann dieser Effekt auch von dem orbitalem Charakter der beteiligten Dirac–Kegel verursacht sein. Da der topologische Schutz in Pb1−xSnxSe durch Kristallsymmetrien garantiert ist, wird als letzter intrinsischer Effekt der Einfluss von eindimensionalen Defekten auf die Kantenzustände untersucht. Berücksichtigt werden dabei ein nicht näher klassifizierbarer, oberflächennaher Defekt und Schraubversetzungen. In beiden Fällen kann ebenfalls eine Aufspaltung des Kantenzustands in einen Doppelpeak gezeigt werden. Im zweiten Teil dieser Arbeit werden die Grundlagen für eine Wiederverwendung von (Pb,Sn)Se–Oberflächen bei zukünftige Experimenten mit (magnetischen) Adatomen geschaffen. Durch Kombination von Inoenzerstäubung und Tempern wird dabei nicht nur eine gereinigte Oberfläche erzeugt, sondern es kann auch das Ferminiveau gezielt erhöht oder gesenkt werden. Dieser Effekt beruht auf eine Modifikation der Sn– Konzentration und der von ihr kontrollierten Anzahl an Defektelektronen. Als letztes sind erste Messungen an Cu- und Fe–dotierte Proben gezeigt. Durch die Adatome tritt eine n–Dotierung auf, welche den Dirac–Punkt des Systems in Richtung des Ferminiveaus verschiebt. Sobald er dieses erreicht hat kommt es zu Wechselwirkungsphänomenen an freistehenden Stufenkanten. Dies führt zu einer Doppelpeakstruktur mit einer feinen Aufspaltung von wenigen meV. Das Phänomen ist auf ein schmales Energiefenster beschränkt, bei dem die Lage des Dirac–Punkts nur etwa 5 meV (in beide Richtungen) von der des Ferminiveaus abweichen darf. N2 - First, the simplest possibility of transporting charges and information between twopoints is given by there direct connection due to one dimensional channels. Second,topological materials have exotic and extremely advantageous properties, which makethem suitable for further applications. If these two come together, then a basic understandingof quantum interference or hybridization effects in one-dimensional, topologicalchannels is of fundamental importance. Therefore, in the present work, interactionsof one dimensional, topologically protected edge states, hosted at odd numbered stepedges on the (001) surface of (Pb,Sn)Se, are investigated.Due to the lateral localization to a few nanometers around a step edge and the needto differentiate between even and odd numbered step heights, scanning tunneling microscopyand spectroscopy are the tools of choice. The newly discovered coupling orinteraction effects between neighboring edge states appear as soon as their distancedecrease below a critical value of dcri ≈ 25 nm. This criterion can be met by variousspatial arrangements of step edges. As a result, crossing, parallel and converging stepedges are examined more closely.With the latter, the distance and thus the coupling strength between the two edgechannels changes continuously along the structure. As a result, three coupling regimeswere identified. (I) Starting from a weak interaction, the peak in the spectrum that ischaracteristic of the edge states initially shows a broadening and reduction in intensity.(II) With increasing interaction, the state begins to split into two peaks, so thatfrom dcri ≈ 15nm a double peak can be observed at both step edges. As the distancecontinues to decrease, the splitting reaches values of a few 10 meV, while the intensitycontinues to drop. (III) As soon as two step edges are separated by less than about 5nm, the spectra at the step edges converge against the spectrum over a terrace due tothe decreasing intensity and the decreasing energetic distance of the two peaks to thevan Hove singularities.iiiThe split is asymmetrical in areas I and II, which means that one peak remains roughlyat the original energy, while the other shifts further and further away with increasingcoupling. With regard to the asymmetry, no difference can be determined whether theconverging step edges form an island, a vacancy island or even run completely parallel.There is no preference as to whether the low energy or high energy peak shifts. Onlyin the regime of strong coupling (III) both peaks clearly leave the initial energy.In contrast to this, a considerable influence of the geometry on the spectrum can beobserved, with the included angle as parameter, for intersecting steps. Independentof the angle, there is no longer an edge state at the intersection itself. The statesat the four edges start to decay, depending on the angle, about 10-15nm before thepoint of intersection. Surprisingly, it turns out that in the case of right angled steps nosplitting at all can be observed, while a double peak can be found for all other angles.This discovery indicates orthogonality with respect to a quantum number in the edgestates involved. In addition to a theoretically predicted spin polarization, this effectcan also be caused by the orbital character of the Dirac cones involved.Since the topological protection in Pb1−xSnxSe is guaranteed by crystal symmetries,the last intrinsic effect to be examined is the influence of one dimensional defects onthe edge states. A near-surface defect, which cannot be classified in any more detailand a screw dislocation are taken into account. In both cases, a splitting of the edgestate into a double peak can also be shown.In the second part of this thesis the basis for reuse of surfaces in future experimentswith (magnetic) adatoms is created. The combination of sputtering and annealing notonly creates a cleaned surface, but in addition it tunes the Fermi level in a controllableway. This effect is based on a modification of the Sn concentration and the associatednumber of holes.Finally, the first measurements on Cu and Fe-doped samples are shown. The adatomscause n-doping, which shifts the Dirac point of the system in the direction of theFermi level. As soon as he has achieved this, there is an interaction phenomenon at thefreestanding step edges. This leads to a double peak structure with a fine split of a fewmeV. This phenomenon is limited to a narrow energy window in which the position ofthe Dirac point may only deviate by about 5 meV (in both directions) from that of theFermi level. KW - Topologischer Isolator KW - Rastertunnelmikroskopie KW - PbSnSe KW - Scanning tunneling microscopy KW - edge states KW - Kantenzustand Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-298616 ER - TY - THES A1 - Gold, Stefan T1 - Winkel- und Temperaturabhängigkeit der magnetokristallinen Anisotropieenergie und der mikroskopischen magnetischen Momente des ferromagnetischen Halbmetalls CrO2 T1 - Angle- and temperature dependence of the magnetocrystalline anisotropy energy and the microscopic magnetic moments of the ferromagnetic half metal CrO2 N2 - Im Rahmen dieser Arbeit wurden die magnetischen Eigenschaften des Halbmetalls CrO2 untersucht. CrO2 hat in den letzten Jahren erneut ein sehr starkes Interesse erfahren. Der Grund hierfür liegt darin, dass dieses Material, aufgrund seiner theoretisch vorhergesagten und inzwischen nachgewiesenen Spinpolarisation von nahezu 100 % an der Fermikante und seiner metastabilen Eigenschaften, ein stark diskutierter Kandidat für Spintronic-Anwendungen wie den Quantencomputer ist. Die Möglichkeit der Spininjektion ist für CrO2 gegeben und in der Zwischenzeit auch erfolgreich umgesetzt worden. Die Untersuchungen zielten auf eine Erklärung für die intrinsischen Eigenschaften wie magnetokristalline Anisotropie, magnetischer Dipolterm und dem eigentlich gequenchten Bahnmoment. Die Untersuchungen fanden an den Cr L2,3 und an der O K Kante statt. Insbesondere für die Auswertung an den Cr L2,3-Kanten war es notwendig, mit einer neuartigen Auswertemethodik sämtliche aufgenommenen Daten zu analysieren, da eine herkömmliche Summenregelauswertung leider nicht durchgeführt werden konnte. Der Grund hierfür lag in der zu geringen L2,3-Aufspaltung des leichten 3d-Übergangmetalls Cr. Mit Hilfe der so genannten Momentenanalyse war es nun möglich, die überlappenden Strukturen voneinander zu separieren, und darüber hinaus auch verschiedene Anteile der Bandstruktur verschiedenen spektralen Beiträgen zuzuordnen. Die Ergebnisse an CrO2 zeigten eine sehr starke Abhängigkeit des magnetischen Bahnmomentes, der Summe von Spin und magnetischem Dipolterm sowie der magnetokristallinen Anisotropieenergie vom Winkel zwischen den rutilen a- und c-Achsen. Noch mehr als das Gesamtbahnmoment zeigen zwei, mit Hilfe der Momentenanalyse separierbare, spektrale Beiträge starke Änderungen der einzelnen Bahnmomente. Dieses unerwartete und ausgeprägte Verhalten konnte mittels eines Vergleichs mit den Sauerstoff K-Kanten XMCD-Daten bestätigt werden, was auf eine sehr starke Hybridisierung der beiden Zustände schließen lässt. Die Trennung der stark anisotropen Summe von Spin-Moment und TZ-Term über die Summenregel für den magnetischen Dipolterm liefert eine Größenordnung des TZ-Terms, wie er bis zu diesem Zeitpunkt nicht vorgefunden wurde. Ein Vergleich der magnetokristallinen Anisotropieenergie, gewonnen durch die Messung von elementspezifischen Hysteresekurven mit Hilfe des XMCD-Effektes, mit dem Brunomodell, das eine magnetisch leichte Richtung für die Achse mit dem größten Bahnmoment vorhersagt, kommt zu keinem positiven Ergebnis. Erst die von G. van der Laan aufgezeigte Erweiterung, in der auch der TZ-Term mit aufgenommen ist, liefert für das System CrO2 ein quantitativ übereinstimmendes Ergebnis der MAE mit den gemessenen experimentellen Momenten. Erwähnenswert in diesem Zusammenhang ist die Tatsache, dass das Bahnmoment und der magnetische Dipolterm unterschiedliche leichte Richtungen bevorzugen und beide Anteile fast gleich groß sind, wobei der magnetische Dipolterm die Überhand hat. In einem zweiten Teil der Arbeit wurde nun auch eine Temperaturabhängigkeit untersucht. Ziel war es, Aussagen über die Entstehung von Bahnmomenten, Dipolterm und MAE in Abhängigkeit des vorliegenden Spinmomentes zu gewinnen und diese mit vorhandenen theoretischen Modellen zu vergleichen. Das gemessene Spinmoment wurde mit SQUID-Daten verglichen und zeigte eine qualitative Übereinstimmung. Die extrahierten Bahnmomente zeigten wie der magnetische Dipolterm ein identisches Temperaturverhalten wie das Spinmoment. Dies ist ein Beweis, dass beide Momente in einem solchen System nur durch eine Kopplung mit dem Spinmoment entstehen und durch dieses verursacht sind. Im Weiteren konnte auch eine quadratische Abhängigkeit der MAE vom Spinmoment nachgewiesen werden. Dieses von G. van der Laan und in Vorarbeiten von P. Bruno vorhergesagte Verhalten konnte erstmalig in dieser Arbeit verifiziert werden. Zusammenfassend lässt sich sagen, dass in dieser Arbeit das ungewöhnliche magnetische Verhalten, insbesondere die Winkelabhängigkeit der magnetischen Momente, durch die Kombination von XAS- und XMCD-Spektroskopie, mit der Verwendung der Momentenanalyse sowie der Untersuchung durch elementspezifische Hystereskurven, ein geschlossenes Bild des Probensystems CrO2 aufgezeigt werden konnte. Das Gesamtbild, das sich ergeben hat, zeigt ganz deutlich auf, dass eine Bandstrukturbeschreibung das gefundene Verhalten erklären kann. Die allgemein vorherrschende, und sicherlich im ersten Moment deutlich intuitivere Vorstellung, dass man im Falle von CrO2 eine Art ionische Bindung hätte, mit einer d2-Konfiguration und erwarteten 2 µB magnetischem Moment am Cr-Platz kann insbesondere die Temperaturabhängigkeit der Anisotropieenergie nicht erklären. Auch in diesem Zusammenhang liefert das Bandmodell eine sehr gute Beschreibung. N2 - In this work, the magnetic properties of the half metal CrO2 were analyzed. CrO2 has attracted a very strong interest due to its theoretical predicted and meantime proven spin polarization of near 100 % at the Fermi-edge, which makes it a strong candidate for a spintronic device or quantum computing. Even a spin injection is possible for CrO2 and has been shown in literature. The aim of this work was to examine, by use of XMCD-effect and additional measurements with SQUID-magnetometer, spin moments and hysteresis loops, but also to clarify the intrinsic properties like magnetocrystalline anisotropy, magnetic dipole term, and the nearly quenched orbital moment. The XMCD-measurements were done at the Cr L2,3- and the O K-edge. Especially for the analysis at the Cr L2,3-edges it was necessary to work with a completely new analysis method, because a “normal” sum rule analysis was not possible. The reason for that is the very small L2,3-exchange energy for the light 3d-transition metal CrO2. By the use of the so called moment analysis it is possible to separate the two transitions from each other and even more to address different features of the XMCD-spectra to different parts of the CrO2-band structure. The idea of this new analysis method for XMCD-spectra is the opportunity to fit spectral forms and analyze these with the use of the ground state moments. With this method, one can draw conclusions, even if there is a spectral overlap between L2 and L3 edges like for CrO2. The results for CrO2 show a strong dependence of the orbital, the sum of spin moment and magnetic dipole term, and the magnetocrystalline anisotropy energy from the angle between rutile a- and c-axis. Even more than the complete orbital moment, two separable and different spectral features show strong alterations of the different orbital moments. This unexpected and pronounced behaviour was approved by a comparison with the O K-edge XMCD spectra, indicating a strong hybridisation of both states. The strong anisotropy of the O K-edge XAS spectra give comparable results to literature. The quantitative analysis of the strong anisotropic sum of spin moment and TZ-term by the use of the magnetic dipole sum rule results in an order of magnitude, which was not found up to now. The comparison of the magnetocrystalline anisotropy energy with the Bruno model, has a negative result. Taking into account the TZ.term, the extension discussed by G. van der Laan, CrO2 shows a good and qualitative agreement between MAE and the measured magnetic moments. Mentionable in this context is the fact, that orbital moment and TZ-term prefer different easy axis. They nearly cancel out each other, but TZ-term is a bit stronger. This might be the reason why CrO2 changes its magnetic easy axis for thin films, because due to the reduction of nearest neighbours and the therefore enhanced orbital moment in thin films, this unstable disequilibrium is distorted. In a second part of this work the temperature dependence was investigated. The aim was to clarify the origin of the orbital moment, dipole term, and MAE in dependence of the spin moment and compare the results to different theoretical models. The measured spin moment was first of all compared with SQUID data. It shows a qualitative agreement, but it shows not the quantitative same behaviour. This was attributed to two reasons, the element specifity of the XMCD effect and its surface sensitivity. The extracted orbital moments and the magnetic dipole term show the same temperature dependence as the spin moment. This is a clear proof, that both, orbital moment and TZ-term, are generated by a coupling to the spin moment. In the following a dependence of the squared measured spin moment could be found for the MAE. This was predicted by Bruno and van der Laan and could be proven for the first time. Recapitulating one can say, that in this work the unusual magnetic behaviour, especially the angle dependence of the magnetic moments, was shown a conclusive description of CrO2 by the combination of XAS and XMCD together with the new moment analysis and the use of element specific hysteresis loops. For the first time the magnetic dipole term could be identified as the reason of the magnetocrystalline anisotropy energy. This proves the model of G. van der Laan, even verified by the temperature dependence for a wide temperature range. A strong Cr – O hybridisation was found, which shows in a similar structure and temperature dependence of the orbital moments for Cr L2,3 and the XMCD effect at O – K edge. The general view shows clearly, that a band structure description can explain the measured dependencies. The intuitional and widely common belief of an ionic binding for CrO2, two electrons at the Cr with a magnetic moment of 2 µB, cannot elucidate especially the temperature dependence of the MAE, which is again good represented by a band structure description. KW - Chromoxid KW - Magnetische Eigenschaft KW - Magnetismus KW - XMCD KW - CrO2 KW - Anisotropieenergie KW - Halbmetall KW - magnetism KW - XMCD KW - CrO2 KW - anisotropy energy KW - half metal Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-20141 ER - TY - THES A1 - Brendel, Harald T1 - Wärmetransport in keramischen Faserisolationen bei hohen Temperaturen T1 - Heat-transfer in ceramic fibre-insulation-materials at high temperatures N2 - Das Ziel dieser Arbeit ist eine umfassende numerische und experimentelle Charakterisierung des Wärmetransports in oxidkeramischen Faserisolationen im Hochtemperaturbereich. Zugleich sollen neue Konzepte für eine optimierte technische Auslegung von Faserisolationen erarbeitet werden. Oxidkeramiken zeigen im Infrarotbereich ein semitransparentes Verhalten. Das bedeutet, ein Teil der Strahlung gelangt durch die Probe, ohne gestreut oder absorbiert zu werden. Durch die Ausgestaltung als disperses Medium mit Abmessungen der Fasern im $\mu m$ Bereich wird jedoch eine starke Wechselwirkung mit infraroter Lichtstrahlung erzeugt. Man befindet sich im optischen Resonanzbereich. Technisch relevante Faserisolationen besitzen eine Rohdichte zwischen $50 \mathrm{kg/m^3}$ und $700 \mathrm{kg/m^3}$ und können als optisch dichtes Medium betrachtet werden. Eine Optimierung hinsichtlich der Dämmwirkung gegen Wärmestrahlung bedeutet eine massenspezifische Maximierung des Lichtstreuvermögens im relevanten Wellenlängenbereich. Hierzu werden in einer numerischen Studie keramische Hohlfaserisolationen mit konventionellen Fasern verglichen. Diese Abhandlung unter Berücksichtigung anwendungsnaher Aspekte gelangt zu der Schlussfolgerung, dass die Strahlungswärmestromdichte in Hohlfaserisolationen, im Vergleich zu konventionellen Isolationen, signifikant erniedrigt wird. Hinsichtlich der Gesamtwärmeleitfähigkeit ist eine Reduzierung um den Faktor zwei zu erwarten. \\ Trotz moderner Rechner ist die Anwendung der vollen Maxwellschen Streutheorie, insbesondere im Rahmen von Optimierungsaufgaben mehrschichtiger Streukörper, ein zeitaufwendiges Unterfangen. Um sinnvolle Parameterkonfigurationen bereichsweise eingrenzen zu können, wird eine Näherungsmethode für die Lichtstreuung an mehrschichtigen Zylindern weiterentwickelt und mit der vollständigen Maxwellschen Streutheorie verglichen. Es zeigt sich, dass das Modell für kleine bis moderate Brechungsindizes sehr gute Vorhersagekraft besitzt und auch zur näherungsweisen Berechnung der Streueffizienzen für räumlich isotrop angeordnete Zylinder herangezogen werden kann. \\ Neben den numerischen Studien wird im experimentellen Teil dieser Arbeit eine kommerzielle Faserisolierung aus Aluminiumoxid hinsichtlich ihrer Wärmetransporteigenschaften charakterisiert. Die optischen Transportparameter Albedo und Extinktion werden mittels etablierter Messmethoden bestimmt. Bei bekannter Faserdurchmesserverteilung können diese Messwerte dann mit den theoretischen Vorhersagen der Maxwellschen Streutheorie verglichen werden.\\ Um technische Optimierungsmaßnahmen experimentell zu verifizieren, besteht die Notwendigkeit, die Temperaturleitfähigkeit bzw. die Wärmeleitfähigkeit auch bei hohen Temperaturen oberhalb von $1000^\mathrm{o}\mathrm{C}$ zuverlässig bestimmen zu können. Zu diesem Zweck wird ein Versuchsaufbau realisiert, um in diesem Temperaturbereich erstmals die sogenannte Thermal-Wave-Analyse anzuwenden. Durch Abgleich mit einem gekoppelten Wärmetransportmodell und einem etablierten Messverfahren wird die besondere Eignung der Thermal-Wave-Analyse für berührungsfreie Hochtemperaturmessungen gezeigt. N2 - The objective of the present thesis is a comprehensive numerical and experimental characterization of the heat transfer properties in thermal insulation materials made of ceramic fibers at high temperatures. At the same time, new concepts for further improvement of fibrous insulation materials are developed. In general, ceramic oxides appear semitransparent in the infrared range, meaning that a part of the thermal radiation is transmitted through a sample without being scattered or absorbed. However, in a dispersed medium containing fibers with diameters in the micrometer range a strong interaction with infrared radiation occurs. Since typical fibrous insulation materials of technical relevance show raw densities between $50 \mathrm{kg/m^3}$ and $700 \mathrm{kg/m^3}$ they could be considered as optically dense. The optimization of the insulation effect involves the maximization of the mass specific scattering coefficient in the wavelength range of substantial thermal radiation. Therefore, the heat transfer properties of hollow-fiber insulation materials are compared to conventional insulations made of solid fibers by means of a numerical study. This treatise concludes that thermal insulations made of hollow fibers can provide a significant reduction of heat losses in wide ranges of practical interest. In particular, by application of hollow fiber insulations the effective thermal conductivity could be lowered by a factor of two.\\ However, in connection with optimization problems of stratified scattering objects the application of the full Maxwell-scattering theory is a time consuming task. In order to locate reasonable parameter configurations in layered cylindrical media an enhanced version of the so-called anomalous diffraction approximation is presented. By comparison with the results of the exact Maxwell-scattering formulas it is shown that within the limit of moderate refractive indices the simplified theory delivers good agreement in a broad size parameter range. Even the extinction efficiency of randomly oriented stratified cylinders is reproduced astonishingly well.\\ Apart from numerical investigations the heat transfer properties of a commercial fibrous insulation material are characterized experimentally. Therefore, the optical transport parameters extinction and albedo are determined by established methods. With knowledge of the fiber diameter distribution the experimental results could be compared to the theoretical predictions of light scattering at infinite fibers. The verification of optimization measures, requires also an adequate experimental determination of thermal diffusivity or thermal conductivity, respectively. For this purpose the potential of measuring thermal diffusivity of heterogeneous materials in a temperature range above $1000^\mathrm{o}C$ by thermal wave analysis is investigated for the first time. By comparison with a coupled numerical heat transfer model and an established measurement method the feasibility of measuring thermal diffusivity at high temperatures by thermal wave analysis is demonstrated KW - Wärmeübertragung KW - Hochtemperatur-Wärmeisolation KW - high temperature thermal insulation materials KW - partizipierende Medien KW - Wärmetransport KW - keramische Fasern KW - light scattering and absorption KW - heat transfer KW - ceramic fibers KW - Keramikfaser KW - Faser KW - Hohlfaser KW - Hochtemperatur Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-157917 ER - TY - THES A1 - Graetz [geb. Dittmann], Jonas T1 - X-Ray Dark-Field Tensor Tomography : a Hitchhiker's Guide to Tomographic Reconstruction and Talbot Imaging T1 - Röntgen-Dunkelfeld-Tensor-Tomographie : ein Handbuch zur Tomographischen Rekonstruktion und Talbot-Bildgebung N2 - X-ray dark-field imaging allows to resolve the conflict between the demand for centimeter scaled fields of view and the spatial resolution required for the characterization of fibrous materials structured on the micrometer scale. It draws on the ability of X-ray Talbot interferometers to provide full field images of a sample's ultra small angle scattering properties, bridging a gap of multiple orders of magnitude between the imaging resolution and the contrasted structure scale. The correspondence between shape anisotropy and oriented scattering thereby allows to infer orientations within a sample's microstructure below the imaging resolution. First demonstrations have shown the general feasibility of doing so in a tomographic fashion, based on various heuristic signal models and reconstruction approaches. Here, both a verified model of the signal anisotropy and a reconstruction technique practicable for general imaging geometries and large tensor valued volumes is developed based on in-depth reviews of dark-field imaging and tomographic reconstruction techniques. To this end, a wide interdisciplinary field of imaging and reconstruction methodologies is revisited. To begin with, a novel introduction to the mathematical description of perspective projections provides essential insights into the relations between the tangible real space properties of cone beam imaging geometries and their technically relevant description in terms of homogeneous coordinates and projection matrices. Based on these fundamentals, a novel auto-calibration approach is developed, facilitating the practical determination of perspective imaging geometries with minimal experimental constraints. A corresponding generalized formulation of the widely employed Feldkamp algorithm is given, allowing fast and flexible volume reconstructions from arbitrary tomographic imaging geometries. Iterative reconstruction techniques are likewise introduced for general projection geometries, with a particular focus on the efficient evaluation of the forward problem associated with tomographic imaging. A highly performant 3D generalization of Joseph's classic linearly interpolating ray casting algorithm is developed to this end and compared to typical alternatives. With regard to the anisotropic imaging modality required for tensor tomography, X-ray dark-field contrast is extensively reviewed. Previous literature is brought into a joint context and nomenclature and supplemented by original work completing a consistent picture of the theory of dark-field origination. Key results are explicitly validated by experimental data with a special focus on tomography as well as the properties of anisotropic fibrous scatterers. In order to address the pronounced susceptibility of interferometric images to subtle mechanical imprecisions, an efficient optimization based evaluation strategy for the raw data provided by Talbot interferometers is developed. Finally, the fitness of linear tensor models with respect to the derived anisotropy properties of dark-field contrast is evaluated, and an iterative scheme for the reconstruction of tensor valued volumes from projection images is proposed. The derived methods are efficiently implemented and applied to fiber reinforced plastic samples, imaged at the ID19 imaging beamline of the European Synchrotron Radiation Facility. The results represent unprecedented demonstrations of X-ray dark-field tensor tomography at a field of view of 3-4cm, revealing local fiber orientations of both complex shaped and low-contrast samples at a spatial resolution of 0.1mm in 3D. The results are confirmed by an independent micro CT based fiber analysis. N2 - Die Röntgen-Dunkelfeld-Bildgung vermag den Widerspruch zwischen dem Bedarf nach großen Sichtfeldern im Zentimeterbereich und der nötigen Bildauflösung zur Charakterisierung von Fasermaterialien mit Strukturgrößen im Mikrometerbereich aufzulösen. Sie bedient sich dafür der Eigenschaft von Röntgen-Talbot-Interferometern, Ultrakleinwinkelstreueigenschaften einer Probe vollflächig abzubilden, womit eine Lücke von mehreren Größenordnung zwischen der Bildauflösung und der konstrastgebenden Strukturgröße überbrückt werden kann. Der Zusammenhang zwischen Strukturanisotropie und gerichteter Streuung ermöglicht dabei Rückschlüsse auf die Orientierung der Mikrostruktur einer Probe unterhalb der Bildauflösung. Erste Demonstrationen haben, basiered auf verschiedenen heuristischen Signalmodellen und Rekonstruktrionsansätzen, die grundsätzliche Erweiterbarkeit auf die Volumen-Bildgebung gezeigt. In der vorliegenden Arbeit wird, aufbauend auf einer umfassenden Analyse der Dunkelfeld-Bildgebung und tomographischer Rekonstruktionsmethoden, sowohl ein verifiziertes Modell der Signalanisotropie als auch eine Rekonstruktionstechnik entwickelt, die für große tensorwertige Volumina und allgemeine Abbildungsgeometrien praktikabel ist. In diesem Sinne wird ein weites interdisziplinäres Feld von Bildgebungs- und Rekonstruktionsmethoden aufgearbeitet. Zunächst werden anhand einer neuen Einführung in die mathematische Beschreibung perspektivischer Projektionen essenzielle Einsichten in die Zusammenhänge zwischen der greifbaren Realraum-Darstellung der Kegelstrahl-Geometrie und ihrer technisch relevanten Beschreibung mittels homogener Koordinaten und Projektionsmatrizen gegeben. Aufbauend auf diesen Grundlagen wird eine neue Methode zur Auto-Kalibration entwickelt, die die praktische Bestimmung von perspektivischen Abbildungsgeometrien unter minimalen Anforderungen an die experimentelle Ausführung ermöglicht. Passend dazu wird eine verallgemeinerte Formulierung des weit verbreiteten Feldkamp-Algorithmus gegeben, um eine schnelle und flexible Volumenrekonstruktion aus beliebigen tomographischen Bildgebungsgeometrien zu ermöglichen. Iterative Rekonstruktionsverfahren werden ebenfalls für allgemeine Aufnahmegeometrien eingeführt, wobei ein Schwerpunkt auf der effizienten Berechnung des mit der tomographischen Bildgebung assoziierten Vorwärtsproblems liegt. Zu diesem Zweck wird eine hochperformante 3D-Erweiterung des klassischen, linear interpolierenden Linienintegrationsalgorithmus von Joseph entwickelt und mit typischen Alternativen verglichen. In Bezug auf die anisotrope Bildmodalität, die die Grundlage der Tensortomographie bildet, wird der Röntgen-Dunkelfeld-Kontrast umfassend besprochen. Die vorhandende Literatur wird dazu in einen gemeinsamen Kontext und eine gemeinsame Nomenklatur gebracht und mit neuen Überlegungen zu einer konsistenten Darstellung der Theorie zur Dunkelfeldsignalentstehung vervollständigt. Zentrale Ergebnisse werden dabei explizit anhand experimenteller Daten verifiziert, wobei besonders die Tomographie und die Eigenschaften anisotroper, faseriger Streuer im Vordergrund stehen. Um die ausgeprägte Empfindlichkeit interferometrischer Bilder auf feinste mechanische Instabilitäten zu kompensieren, wird ein effizientes Optimierungsverfahren zur Auswertung der Rohdaten aus Talbot-Interferometern entwickelt. Schließlich wird die Anwendbarkeit von linearen Tensor-Modellen in Bezug auf die hergeleiteten Anisotropie-Eigenschaften des Dunkelfeld-Kontrastes diskutiert, und ein iteratives Verfahren für die Rekonstruktion tensorwertiger Volumen aus Projektionsbildern vorgeschlagen. Die entwickelten Methoden werden effizient implementiert und auf Proben aus faserverstärktem Kunstoff angewandt, die dafür an der Bildgebungs-Strahllinie ID19 des Europäischen Synchrotrons ESRF abgebildet wurden. Die Ergebnisse stellen eine bisher einmalige Demonstration von Röntgen-Dunkelfeld-Tensor-Tomographie mit einem Sichtfeld von 3-4cm dar, wobei lokale Faserorientierung sowohl für komplex geformte als auch kontrastarme Objekte mit einer räumlichen Auflösung von 0.1mm in 3D dargestellt werden kann. Ein unabhängiger Vergleich mit Mikro-CT basierter Faser-Analyse bestätigt die Ergebnisse. KW - Dreidimensionale Rekonstruktion KW - Tomografie KW - Faserorientierung KW - Tensor KW - Bildgebendes Verfahren KW - X-Ray Dark-Field KW - Tensor Tomography KW - Volume Reconstruction KW - Fiber Orientation Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-281437 ER - TY - THES A1 - Weigand, Frank T1 - XANES und MEXAFS an magnetischen Übergangsmetalloxiden : Entwicklung eines digitalen Lock-In-XMCD-Experiments mit Phasenschieber T1 - XANES and MEXAFS studies of magnetic transition metal oxides Development of a digital Lock-In XMCD experiment with phase retarder N2 - In dieser Arbeit werden drei Lanthanmanganat-Systeme mittels SQUID-(Superconducting Quantum Interference Device) Magnetometrie und XMCD-(X-ray Magnetic Circular Dich-roism) Messungen an den jeweiligen Absorptionskanten (XANES: X-ray Absorption Near Edge Structure) sowie im kantenfernen Bereich (MEXAFS: Magnetic Extended X-ray Ab-sorption Fine Structure) im Hinblick auf die Klärung ihrer magnetischen (Unter-)Struktur untersucht. Bei Lanthanmanganaten wird sowohl im Verlauf des spingemittelten als auch spinabhängigen Absorptionskoeffizienten an der Mn K Kante immer eine energetisch über 40eV ausgedehnte Doppelstruktur beobachtet. Durch Vergleich mit theoretischen Bandstrukturrechnungen und Messungen an Referenzsystemen lassen sich diese Strukturen auf zwei energetisch getrennte, resonante Übergänge in leere Mn 4p Zustände zurückführen. Die Ursachen liegen in der Kristallstruktur der Lanthanmanganate und damit ihrer Bandstruktur begründet. XMCD-Messungen an den La L2,3 Kanten zeigen, dass dieses Element zur Gesamtmagnetisierung dieser Verbindungen nur ein unerhebliches Moment beiträgt und daher in einer Xenon-ähnlichen Elektronenkonfiguration vorliegt. Durch die interatomare Coulombwechselwirkung der nahezu unbesetzten La 5d Zustände mit den magnetisch aktiven Ionen im Kristall dienen XMCD-Messungen an den La L2,3 Kanten als Sonde für die magnetische Lanthanumgebung. Ähnliches gilt für die entsprechenden MEXAFS. Der proportionale Zusammenhang der Größe der MEXAFS mit dem Spinmoment der Nachbarionen besitzt auch bei den Lanthanmanganat-Systemen mit den stark hybridisierten Elektronen der Mn 3d Schale Gültigkeit. Der Spinmoment-Korrelationskoeffizient aSpin gilt auch hier, was eine weitere Bestätigung des MEXAFS-Modells auch für oxidische Systeme ist. Im dotierten System La1.2Nd0.2Sr1.6Mn2O7 koppelt das Neodymmoment innerhalb einer Doppellage antiferromagnetisch zum Mn-Untergitter. Durch die Neodym-Dotierung am La/Sr-Platz im Kristall ist die ferromagnetische Kopplung der Doppellagen untereinander abge-schwächt und die Rückkehr in die antiferromagnetische Phase nach dem Abschalten des äußeren Magnetfeldes damit erleichtert. Das Mn-Bahnmoment ist von nahezu verschwindender Größe („gequencht“). Das System La1.2Sr1.8Mn2-xRuxO7 zeigt mit zunehmendem Rutheniumgehalt eine Erhöhung der Curie-Temperatur, was bei Ruddlesden-Popper Phasen zum ersten Mal beobachtet wurde. Das Ru-Untergitter und das Mn-Gitter sind zueinander antiparallel gekoppelt. Durch Bestimmung der Valenzen von Mn und Ru wird ein dem Superaustausch ähnliches Kopplungsmodell entworfen, womit der Anstieg in der Curie-Temperatur erklärbar ist. Das neu entwickelte XMCD-Experiment auf Basis eines Phasenschiebers und digitaler Sig-nalaufbereitung durch eine Lock-In Software besitzt ein Signal-Rausch Verhältnis in der Nähe der Photonenstatistik und liefert einen großen Zeit- und Qualitätsgewinn gegenüber Messmethoden mit Magnetfeldwechsel. Auf teure analoge Lock-In Messverstärker kann verzichtet werden. Zukünftig erweitert sich mit diesem Aufbau die für XMCD-Experimente zugängliche Anzahl an Synchrotronstrahlplätzen. Diese Experimente sind jetzt auch mit linear polarisierter Röntgenstrahlung an Wiggler/Undulator Strahlplätzen und zukünftigen XFELs (X-ray Free Electron Laser) durchführbar. N2 - In this work three Lanthanum Manganate systems are investigated in terms of their magnetic (sub) structures. These investigations are done with SQUID- (Superconducting Quantum Interference Device) magnetometry and XMCD- (X-ray Magnetic Circular Dichroism) measurements at the respective absorption edges (XANES: X-ray Absorption Near Edge Structure) as well as in the MEXAFS (Magnetic Extended X-ray Absorption Fine Structure) range. For Lanthanum Manganates at the Mn K edge there is always seen a double peak structure in the shape of the spin dependent and spin averaged absorption coefficient, which is energetically expanded over more than 40eV. These structures are ascribed to two energetic separated, resonant transitions into empty Mn 4p states by comparing with theoretical band structure calculations and measurements of reference systems and are caused in the crystal structure of the Lanthanum Manganates and with it their band structure. XMCD-measurements at the La L2,3 edges show that this element adds only a negligible magnetic moment to the total magnetisation and La is therefore in a Xenon-like electronic configuration. These measurements probe the magnetic neighbourhood of the Lanthanum in the crystal due to the interatomic Coulomb interaction of the almost empty La 5d states with the magnetic active ions like the MEXAFS. The proportionality of the MEXAFS amplitude with the spin-moment of the neighboring ions is even valid here for Lanthanum Manganate systems with their strongly hybridized Mn 3d shell electrons. The validity of the correlation coefficient of the spin-moment aSpin confirms the MEXAFS-model also for oxide systems. In the doped system La1.2Nd0.2Sr1.6Mn2O7 the Neodymium moment couples antiferromagnetically with the Mn-sublattice within a double layer. The ferromagnetic coupling of the double layers is weak among each other due to the Nd doping at the La/Sr crystal position. Therefore the reversion into the antiferromagnetic phase is relieved after switching off the external magnetic field. The orbital moment of Mn is almost vanishing (“quenched”). The system La1.2Sr1.8Mn2-xRuxO7 shows an increasing of the Curie-temperature with an increase of the Ruthenium doping level, observed for the first time for Ruddlesden-Popper phases. The Ru-sublattice is antiparallel coupled to the Mn-sublattice. A superexchange like coupling model is composed through determination of the valences of Mn and Ru, also explaining the increase of the Curie-temperature. A new XMCD-experiment is developed with phase retarder and digital signal processing through Lock-In software with signal to noise ratio nearby photon statistics. This experiment provides a huge benefit in time and quality compared to XMCD-measurement with changing the external magnetic field. Also there is no need of expensive Lock-In analog amplifiers. Now the number of synchrotron beamlines for XMCD-measurements are increased and XMCD-experiments are realizable also at Wiggler/Undulator beamlines with linear polarized radiation and in future at XFEL (X-ray Free Electron Laser). KW - Lanthanoxid KW - Manganate KW - XANES KW - EXAFS KW - Röntgenzirkulardichroismus KW - Perowskite KW - CMR-Systeme KW - Phasenschieber KW - digitaler Lock-In KW - XMCD KW - perovskites KW - CMR-systems KW - phase retarder KW - digital Lock-In Y1 - 2003 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-8849 ER - TY - THES A1 - Schumm, Marcel T1 - ZnO-based semiconductors studied by Raman spectroscopy: semimagnetic alloying, doping, and nanostructures T1 - Ramanspektroskopische Untersuchung ZnO-basierte Halbleiter: Semimagnetische Legierung, Dotierung und Nanostrukturen N2 - ZnO-based semiconductors were studied by Raman spectroscopy and complementary methods (e.g. XRD, EPS) with focus on semimagnetic alloying with transition metal ions, doping (especially p-type doping with nitrogen as acceptor), and nanostructures (especially wet-chemically synthesized nanoparticles). N2 - ZnO-basierte Halbleiter wurden mittels Ramanspektroskopie und komplementärer Methoden (z.B. XRD, EPS) untersucht mit den Schwerpunkten semimagnetische Legierung mit Übergangsmetallen, Dotierung (vor allem p-Dotierung mit Stickstoff als Akzeptor) und Nanostrukturen (vor allem nass-chemisch hergestellte Nanopartikel). KW - Wide-gap-Halbleiter KW - Würzburg / Sonderforschungsbereich II-VI-Halbleiter KW - Verbindungshalbleiter KW - Zwei-Sechs-Halbleiter KW - Semimagnetischer Halbleiter KW - n-Halbleiter KW - Niederdimensionaler Halbleiter KW - p-Halbleiter KW - Kolloider Halbleiter KW - Magnetisch KW - Ramanspektroskopie KW - Raman KW - Zinkoxid KW - ZnO KW - DMS KW - Raman spectroscopy KW - Raman KW - Zinc oxide KW - ZnO KW - DMS KW - Diluted Magnetic Semiconductors KW - doping KW - secondary phases Y1 - 2008 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-37045 ER - TY - THES A1 - Scheibner, Michael T1 - Über die Dynamik lokal wechselwirkender Spinträger T1 - About the dynamics of locally interacting spin carriers N2 - In dieser Arbeit wurde die Dynamik spintragender Teilchen (Elektronen, Löcher, Exzitonen) in selbstorganisierten Cd(Mn)Se/ZnSe Quantenpunkten sowie leicht dotiertem GaAs untersucht. Die unterschiedlichen Materialgruppen boten die Möglichkeit verschiedene Einflüsse auf Spinzustände zu studieren. Die Injektion definierter Spinzustände in die Halbleiterstrukturen erfolgte ausschließlich auf optischem Weg. Ebenfalls optisch wurde auch die zeitliche Entwicklung der Spinzustände detektiert. Die Anwendung von zeitaufgelöster Photolumineszenzspektroskopie sowie zeitaufgelöster Kerr-Rotation, ermöglichte den Zugriff sowohl auf longitudinale wie auch transversale Spinrelaxationsprozesse. Desweiteren wurde eine Kopplung der Quantenpunkten über ihr Strahlungsfeld diskutiert. N2 - In this thesis the dynamics of spin carrying particles like electrons, holes and excitons in self-organized Cd(Mn)Se/ZnSe quantum dots and lightly doped GaAs has been studied. The different materials offered the possibility to investigate various influences on spin states. The injection of defined spin states into the semiconductor structures was achieved exclusively by optical means. Likewise, the temporal evolution of the spin states was detected optically. The application of time resolved photoluminescence spectroscopy and time resolved Kerr rotation gave access to longitudinal as well as transverse spin relaxation processes. In addition a coupling of the quantum dots through their radiation field was discussed. KW - Quantenpunkt KW - Spindynamik KW - Quantenpunkte KW - Spindynamik KW - Magneto-optik KW - semimagnetisch KW - Halbleiter KW - zeitafgelöst KW - Strahlungskopplung KW - CdSe KW - GaAs KW - Quantum dots KW - spindynamics KW - magneto optics KW - semi-magnetic KW - semiconductor KW - time resolved KW - radiative coupling KW - CdSe KW - GaAs Y1 - 2005 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-20127 ER -