TY - THES A1 - Spatz, Kerstin T1 - Mechanische und rheologische Eigenschaften von Calciumphosphat-Zementen T1 - Mechanical and rheological properties of calcium phosphate cements N2 - Zur Erhöhung der mechanischen Stabilität mineralischer Knochenzemente aus Calciumorthophosphaten (CPC) wurde in einem TTCP/DCPA-System das Zementedukt TTCP mit verschiedenen biokompatiblen Oxiden (SiO2, TiO2, ZrO2) während des Herstellungsprozesses dotiert. Dies führte zur Bildung von Calciummetallaten und einer Herabsetzung der Löslichkeit der TTCP-Komponente des Zements. Gegenüber einem oxidfreien Zement konnte die Druckfestigkeit von 65 MPa auf 80 MPa (SiO2) bzw. 100 MPa (TiO2) gesteigert werden. In einem zweiten Ansatz zur Verbesserung der Injizierbarkeit wurden die Wechselwirkungen der Partikeloberflächen mit der flüssigen Zementphase betrachtet. Durch biokompatible Additive sollte eine repulsive elektrostatische Wechselwirkung eingestellt werden, um Partikelagglomerate effektiv zu dispergieren und eine verflüssigende Wirkung zu erreichen. Die Injizierbarkeit eines TTCP/DCPA-Zements durch eine Kanüle mit 800 µm Durchmesser konnte durch die Verwendung von 500 mM tri-Natriumzitrat-Lösung aufgrund einer deutlichen Herabsetzung der Viskosität der Zementpaste signifikant gesteigert werden (>95%, P/L 3,3/1, Kraftaufwand 20 N). Abschließend wurde der Einfluss der Partikelgrößenverteilung auf die Festigkeit und Injizierbarkeit einer auf monomodaler Partikelgrößenverteilung basierten Zementmatrix untersucht. Hierzu wurden einem mechanisch aktivierten a-TCP-System unreaktive, feinkörnige Füllstoffpopulationen (TiO2, CaHPO4, CaCO3) zugesetzt und systematisch deren Effekt in Verbindung mit einer Partikelaufladung durch tri-Natriumzitrat auf die rheologischen und mechanischen Eigenschaften untersucht. Erst die Kombination einer bimodalen Partikelgrößenverteilung mit tri-Natriumzitrat-Lösung führte zu einer starken Erniedrigung der Viskosität, damit zur nahezu vollständigen Injizierbarkeit der Zemente und einer teilweise signifikanten Steigerung der mechanischen Festigkeiten (z.B. 72 MPa reiner a-TCP-Zement auf 142 MPa mit Zusatz von CaHPO4). N2 - An improvement of the mechanical strength of calcium phosphate bone cements in combination with a lower cement paste viscosity for better injectability was investigated. A first approach to improve the mechanical stability consisted in adding several biocompatible oxides (SiO2, TiO2, ZrO2) during the fabrication process of tetracalcium phosphate (TTCP). The formation of calcium metallates led to a decrease of the solubility of the oxide doped tetracalcium phosphates. The cements based on tetracalcium phosphates mixed with SiO2 and TiO2 exhibit a significant increase of the compressive strengths (65 MPa of pure cement up to 80 MPa (SiO2) and 100 MPa (TiO2)). A second approach to decrease the viscosity of CPC pastes considered the interactions between the particle surfaces and the liquid cement phase. To disperse agglomerates and improve the injection properties of CPC, biocompatible components were added to the liquid phase. As a result the injection properties of the TTCP/DCPA cement improved significantly. The use of 500 mM trisodium citrate solution as liquid phase changed the viscosity of the cement paste to a point, where complete injectability (> 95%) through an 800 mm diameter hypodermic needle could be achieved at low loads (20 N). In order to transfer the results of a multi-constituent cement to a single reactive component cement, different fine-particle-sized fillers were added to mechanically activated, monomodal α-tricalcium phosphate (α-TCP) cement. The inert fillers dicalcium phosphate anhydrous (DCPA), titanium dioxide (TiO2) and calcium carbonate (CC) were added to the α-TCP-matrix in different concentrations. For an effective ionic modification a 500 mM trisodium citrate solution was used as liquid phase as in the aforementioned TTCP/DCPA cement system. Only the combination of a bimodal particle size distribution and trisodium citrate solution led to a nearly complete injectability and a significantly increase of the mechanical stability of CPC. KW - Biomaterial KW - Knochenzement KW - Calciumphosphate KW - Implantatwerkstoff KW - Rheologie KW - Calciumphosphat KW - calcium phosphate KW - injectability KW - zetapotential KW - mechanical properties KW - tricalcium phosphate KW - Rheologie KW - Zetapotential KW - mechanische Eigenschaften Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-124860 ER - TY - JOUR A1 - Ojha, Animesh K. A1 - Forster, Stefan A1 - Kumar, Sumeet A1 - Vats, Siddharth A1 - Negi, Sangeeta A1 - Fischer, Ingo T1 - Synthesis of well–dispersed silver nanorods of different aspect ratios and their antimicrobial properties against gram positive and negative bacterial strains JF - Journal of Nanobiotechnology N2 - In the present contribution, we describe the synthesis of highly dispersed silver nanorods (NRs) of different aspect ratios using a chemical route. The shape and size of the synthesized NRs were characterized by Transmission Electron Microscopy (TEM) and UV-visible spectroscopy. Longitudinal and transverse absorptions bands confirm the rod type structure. The experimentally recorded UV-visible spectra of NRs solutions were fitted by using an expression of the extinction coefficient for rod like nano structures under the dipole approximation. Simulated and experimentally observed UV-visible spectra were compared to determine the aspect ratios (R) of NRs. The average values of R for NR1, NR2 and NR3 solutions are estimated to be 3.0 ± 0.1, 1.8 ± 0.1 and 1.2 ± 0.1, respectively. These values are in good agreement with those obtained by TEM micrographs. The silver NRs of known aspect ratios are used to study antimicrobial activities against B. subtilis (gram positive) and E. coli (gram negative) microbes. We observed that the NRs of intermediate aspect ratio (R = 1.8) have greater antimicrobial effect against both, B. subtilis (gram positive) and E. coli (gram negative). The NRs of aspect ratio, R = 3.0 has better antimicrobial activities against gram positive than on the gram negative. KW - antimicrobial activities KW - silver KW - nano rods KW - TEM Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-132222 VL - 11 IS - 42 ER - TY - THES A1 - Beyer, Matthias T1 - Untersuchungen zu photovernetzbaren und biokompatiblen (Hybrid-)Polymeren T1 - Investigations of photo-curable and biocompatible (hybrid) polymers N2 - Die Arbeit beschäftigte sich mit Untersuchungen zu photovernetzbaren und –strukturierbaren (Hybrid-)Polymeren, um Grundlagen für die Herstellung von Trägergerüststrukturen (Scaffolds) auf Basis photovernetzbarer (Hybrid-)Polymere zu legen und damit in der Zukunft patientenindividuelle medizinische Werkstücke, die beliebig durch Zwei-Photonen-Absorptionsprozesse in drei Dimensionen strukturierbar sind, für die Regenerative Medizin zu ermöglichen. Dafür wurden zunächst die zum Teil in der Literatur unbekannten unterschiedlichen Monomere Acr-1, MAcr-2, Acr-3, MAcr-4 und DiMAcr-5 synthetisiert. Dabei handelt es sich um einfache und gut vergleichbare organische (Meth-)Acrylat-Monomere, die mono- bzw. difunktional in ihren photochemisch reaktiven Gruppen sind. Die synthetisierten organischen Monomere Acr-3, MAcr-4 und DiMAcr-5 wurden in verschiedenen Verhältnissen mit dem anorganisch-organischen Methacrylat-basierten Hybridpolymers ORMOCER® I kombiniert. Die (Co-)Polymerisation der unterschiedlichen Formulierungen wurde in situ mittels UV-DSC-Untersuchung verfolgt. Dabei wurden bei diesen Untersuchungen zum Teil deutliche Unterschiede im Reaktionsverlauf der einzelnen Materialformulierungen festgestellt. So konnten zum Beispiel bei Monomermischungen ein schnellerer Polymerisationsverlauf sowie eine höhere maximale Polymerisationsrate als bei den jeweiligen Einzelkomponenten beobachtet werden (Synergieeffekt). Diese Beobachtungen wurden anhand der Monomerstruktur (unterschiedliche Diffusionsfähigkeiten im vergelten, aber noch nicht erstarrten System durch Mono- bzw. Difunktionalität) und der Art der funktionellen Gruppe (Acrylat- bzw. Methacrylatgruppe) erklärt. Weiterhin wurden der Einfluss des verwendeten Photoinitiators und dessen eingesetzte Konzentration auf die photochemisch-induzierte Copolymerisation eines ausgewählten Systems beleuchtet. Dazu wurden verschiedene Einflussfaktoren der Initiation betrachtet. Neben der eingesetzten Initiatorkonzentration spielen auch die Absorptionseigenschaften, die umgebende Matrix und die Initiatoreffizienz eine große Rolle für den Reaktionsverlauf der photochemischen Vernetzung. Weiterhin wurden die Photoinitiatoren in unterschiedlichen Konzentrationen eingesetzt, um die dadurch induzierte Veränderung des Reaktionsverlaufs zu betrachten. Aus den Einflüssen auf die Reaktionsverläufe konnte geschlossen werden, dass diese sowie auch die maximale Polymerisationsrate RP,max und damit die Reaktionskinetik nicht in jedem Fall linear mit der Initiatorkonzentration zunehmen muss. Erste generelle 2PP-Strukturierungen wurden zudem an ausgewählten Material-formulierungen durchgeführt. Dabei zeigte sich, dass alle Formulierungen bei bestimmten Parameterkombinationen aus Laserleistung und Schreibgeschwindigkeit mittels 2PP strukturiert werden konnten. Außerdem wurden bei den verschiedenen Formulierungen bei gleicher Parameterkombination unterschiedliche Strukturbreiten und damit erstmalig unterschiedliche Strukturvolumina beobachtet. Diese unterschiedlichen Volumina konnten erstmalig mit den unterschiedlichen Reaktionsverläufen der Materialformulierungen korreliert werden. Dabei zeigte sich, dass das chemische Wechselwirkungsvolumen von der Funktionalität der eingesetzten Materialkomponenten abhängig ist, da davon der Grad an Quervernetzung abhängt, der bestimmt, ob ausreichend vernetzte Voxel und Strukturen entstehen, die durch einen Entwicklungsschritt nicht mehr entfernt werden. Im zweiten Teil der Arbeit wurde ein biokompatibles und photostrukturierbares Hybridpolymer (RENACER® MB-I) entwickelt, welches mittels 2PP strukturiert werden konnte, was anhand kleiner wie auch großer Scaffolds mit dem Material demonstriert wurde. Dazu wurde das kommerziell erhältliche Alkoxysilan-Molekül O-(Methacryloxyethyl)-N-(triethoxysilylpropyl)urethan als Precursor verwendet. Durch eine bewusst unvollständige Hydrolyse- und Kondensationsreaktion konnte aus dem Precursorsilan ein Hybridpolymerharz hergestellt werden, welches anorganisch vorverknüpft war. Weiterhin wies es sowohl als Volumenpolymer, als auch in Form von Scaffold-Strukturen eine sehr gute Biokompatibilität auf. Um zu untersuchen, ob die im Hybridpolymer enthaltenen prinzipiell degradierbaren Gruppen unter physiologischen Bedingungen tatsächlich degradieren und Teile aus dem Polymerverband herausgelöst werden können, wurde ein selbstentwickeltes Verfahren für stationäre Degradations-untersuchungen in phosphat-gepufferter Saline (PBS, pH = 7,4) verwendet. Die durch die photochemische Polymerisation neu entstandenen Ketten besaßen ihrer Natur gemäß keine hydrolysierbaren Einheiten, weshalb das Hybridpolymer nicht vollständig degradieren kann. Es konnte jedoch ein prinzipieller Zugang zu Gerüstträgerstrukturen auf Basis photovernetzbarer Polymere für die Regenerative Medizin geschaffen werden. N2 - The objective was the investigation of photo-curable and patternable (hybrid) polymers for applications in regenerative medicine, in order to explore basic principles for scaffold fabrication by two-photon polymerization. This would enable patient-individual medical implants. As model systems for subsequent investigations, the monomers Acr-1, MAcr-2, Acr-3, MAcr-4, and DiMAcr-5 were synthesized. These compounds are well comparable organic (meth)acrylate monomers with a functionality of one and two, respectively. The monomers Acr-3, MAcr-4, and DiMAcr-5 were combined with a well-known methacrylate-based inorganic-organic hybrid polymer ORMOCER® I in different molar ratios. After preparation of the monomers and their formulations with ORMOCER® I introducing defined amounts of photoinitiator Irgacure® 369 into the material systems, the materials’ reaction was monitored in situ by photo-DSC investigations. In particular, the effect of the different monomer ratios on the copolymerization behavior was studied in more detail. A higher maximum polymerization rate and, therewith, a higher reaction speed was found for all formulations of monomer mixtures in contrast to the corresponding individual monomers (synergy effect). Moreover, by comparing the various organic monomers, considerable differences could be identified in between acrylates and methacrylates as well as for the mono- and difunctional species. These effects were explained by means of the type of their photochemically organically cross-linkable functional groups and thus their resulting reactivity as well as by the monomer structure and functionality itself, resulting in different diffusion abilities of mono-, oligo- and polymeric species within gelled systems. Furthermore, the influence of several photoinitiators and the initiator concentration on the photochemically induced copolymerization was investigated. Besides the initiator concentration, also the initiators’ absorption properties, the resin matrix and the initiators’ efficiency play an important role for the reaction profile of the photochemical cross-linking. All different photoinitiators were introduced into the model system in three different concentrations to explore the induced alterations on the reaction profile. For some of the investigated initiators, the maximum polymerization rate RP,max and, therewith, the overall reaction kinetics increased with increasing photoinitiator concentration, but for other initiators, the maximum polymerization rate RP,max was lowered at increased initiator concentrations. Thus, a general relationship between the photoinitiator concentration and the maximum polymerization rate RP,max could not be identified. First structures were generated out of selected mixtures by two-photon polymerization in order to demonstrate the novel materials’ ability of being patterned in three dimensions. Three dimensional structures were generated with specific parameter combinations of laser power and writing speed, whereas each parameter set corresponds to an individual exposure dose deposited in the materials’ volume. In particular, different structure widths were observed for different material formulations fabricated with the same parameter sets. Thus, it was possible for the first time to experimentally observe different chemical interaction volumes. These interaction volumes were correlated to the different reaction profiles of the material formulations, which were received via 1PP photo-DSC measurements. It was shown that the structure volume depends on the functionality of the employed monomers, because their degree of cross-linking depends on their functionality. The degree of cross-linking which results upon polymerization determines, whether a structure maintains stable during the subsequent development process. In the second part of this work, a biocompatible and photo-patternable hybrid material was developed. Commercially available O-(methacryloxyethyl)-N-(triethoxysilylpropyl)-urethane was chosen for an intentional incomplete hydrolysis and condensation reaction in order to receive a RENACER® resin, which includes functional groups for subsequent organic cross-linking. This material showed a very good patterning performance, which was demonstrated by a series of structures and scaffolds. The material yields a good biocompatibility. In order to investigate, whether the hydrolysable functional groups within the hybrid polymer actually degrade under physiological conditions, a procedure routine for stationary degradation studies in phosphate-buffered saline (PBS) was developed. The carbon chain generated through photochemical cross-linking, has no hydrolyzable groups and naturally cannot be degraded, resulting in a hybrid polymer which is not completely degradable. However, a principal access to scaffolds for regenerative medicine on the basis of photo-curable polymers was accomplished which was the purpose of this work. KW - Photopolymerisation KW - Zwei-Photonen-Polymerisation KW - Copolymerisation KW - Reaktionskinetik KW - Biokompatibilität KW - Photo-DSC KW - Kinetik Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-97131 ER - TY - THES A1 - Grotz, Michael T1 - Synthese und Charakterisierung abiotischer Foldamere und ihrer Bausteine für die Nutzung in biologischen Systemen T1 - Synthesis and characterization of abiotic foldamers and their components for use in biological systems N2 - Die vorliegende Arbeit befasst sich mit der Synthese, Charakterisierung und Untersuchung von Foldameren und ihren Untereinheiten im Rahmen des FOLDAPPI-Projekts (Foldamers against Protein-Protein Interaction). Des Weiteren wurden neuartig substituierte Chinoline dargestellt, um sie im Rahmen des SFB 630 auf ihre Hemmwirkung gegen Leishmanien und Trypanosomen zu untersuchen. Im ersten Projekt wurde ein neuartiges Monomer entwickelt, welches die Wasserlöslichkeit der Foldamere verbessern sollte. Zu diesem Zweck wurde eine zusätzliche, hoch polare Seitenkette in den Chinolingrundkörper eingeführt. Dieses modifizierte Monomer konnte erfolgreich synthetisiert werden. Um die Verbesserung der Wasserlöslichkeit gegenüber dem zuvor verwendeten Monomer zu testen, wurde erfolgreich ein Tetramer daraus aufgebaut. Das entschützte Tetramer konnte jedoch aufgrund seiner hohen Polarität nicht ausreichend gereinigt werden, um die abschließenden Löslichkeitsuntersuchungen durchzuführen. Um dieses Problem zu umgehen, wurde von der Umsetzung in Lösung auf Reaktionen an der Festphase gewechselt, was die Reinigung der Produkte wesentlich erleichtern sollte. Dabei wurde eine vom Arbeitskreis von I. Huc neu entwickelte mikrowellengestützte Methode verwendet. Das Referenzmolekül mit den bisher verwendeten Seitenketten konnte so ohne Probleme synthetisiert und seine Löslichkeit in Wasser bestimmt werden. Beim neu entwickelten Monomer kam es allerdings beim Aufbau des Tetrameres zu einer Zersetzungsreaktion, weshalb das abschließende Ziel nicht erreicht werden konnte. Im zweiten Projekt wurden zwei Ziele angestrebt: Zunächst sollte ein Weg gefunden werden, die Einführung der Seitenketten an den Chinolinen erst an der festen Phase vorzunehmen, wodurch viele Syntheseschritte bei der Vorbereitung der Monomere gespart werden könnten. Zusätzlich sollte eine neue Kupplungsreaktion entwickelt werden, wodurch der Entschützungsschritt des zu kuppelnden Amins an der Festphase eingespart werden kann. Dadurch würde vor allem bei großen Foldameren das Harz geschont und die Gefahr einer Degenerierung wesentlich verringert. Für die Kupplungsreaktion vorgesehen war ein azidfunktionalisiertes Monomer, das mittels Staudinger-Reaktion verknüpft werden sollte. Das entsprechende Monomer konnte erfolgreich synthetisiert werden. Auch das erste Ziel, die Einführung der Seitenkette an der Festphase, konnte erfolgreich durchgeführt werden. Leider war die Verwirklichung beider Ziele über die gleiche Syntheseroute nicht ohne weiteres möglich. Da das Monomer ohne die Seitenkette deutlich hydrophiler wurde, wäre eine Trocknungsmethode bei erhöhter Temperatur von Vorteil gewesen, um gebundenes Wasser vollständig zu entfernen. Da das Monomer allerdings auch eine Azidfunktion trägt und sich bei 130 °C explosionsartig zersetzt, war dies nicht möglich. Allerdings genügen bereits geringe Spuren von Feuchtigkeit, um die Staudinger-Reaktion zu beeinträchtigten. Deshalb konnte das zweite Projektziel nicht verwirklicht werden. Im dritten Projekt wurde die Herstellung einer großen Foldamer-Bibliothek für die Untersuchung der Bindungsaffinität gegenüber IL-4 angestrebt. Sie sollte aus 48 Hexameren bestehen, wobei an drei Monomeren die Seitenketten variiert werden sollten, um ein breites Spektum an verschiedenen Kombinationen von Wechselwirkungen abzudecken. Dazu wurden zunächst vier verschiedene Monomere synthetisiert, welche eine aromatisch, eine unpolare, eine anionische bzw. eine kationische Seitenkette enthielten. Für die Kupplung der Foldamere wurde eine an die Synthese von Aminosäuresequenzen angelehnte Methode entwickelt und erfolgreich angewandt. So konnten alle 48 Foldamere erfolgreich synthetisiert und 46 von ihnen in ausreichenden Mengen für die Untersuchung an IL-4 gereinigt werden. Leider liegen für diese Bibliothek bisher keine abschließenden Ergebnisse über die Inhibitionseigenschaften gegenüber IL-4 vor. Strukturell sehr ähnliche Foldamere zeigten jedoch in ersten Experimenten eine Inhibition von IL-4 was eine Wirksamkeit der neu erstellten Bibliothek vermuten lässt. Das vierte Projekt wurde im Rahmen des SFB 630 durchgeführt. Hierzu wurden einige der ursprünglich für andere Projekte hergestellten Foldamere ausgewählt, teilweise entschützt bzw. an der Nitrogruppe reduziert und anschließend auf Ihre Aktivität gegen Leishmanien und Trypanosomen getestet. Es zeigte sich, dass das verwendete Substitutionsmuster, in den gestesteten Konzentrationen nicht gegen Leishmanien und Trypanosomen wirksam ist. Es eignet sich also nicht für die Erstellung einer neuen Leitstruktur gegen diese beiden Erreger. Allerdings trat im untersuchten Konzentrationsbereich auch keine Zytotoxizität auf, was eine interessante Information für die Verwendung der Foldamere und ihrer Bausteine in biologischen Systemen darstellt. N2 - The present work deals with the synthesis, characterization and testing of foldamers and their sub-units within the FOLDAPPI-project (foldamer against protein-protein interaction). Furthermore, novel substituted quinolines were constructed to be tested in the SFB 630 for their inhibitory activity against Leishmania and Trypanosoma. Within the first project, a novel monomer was developed, in order to improve the water-solubility of the foldamers. For this purpose, an additional, highly polar side chain was introduced into the quinoline core-structure. This modified monomer was successfully synthesized. To test the improvement in water solubility compared to the previously used monomers, a tetramer was successfully constructed. However, the deprotected tetramer could not be sufficiently purified due to its high polarity; thus the final solubility studies could not be performed. In order to avoid this problem, the reaction-path was changed from reactions in solution to the solid phase, which should facilitate the purification of the products significantly. Here, a newly developed (group of I. Huc) microwave-assisted method was used. The reference molecule having the previously used side chains was synthesized without any problems and its solubility in water could be determined. The newly developed monomer, however, shows a decomposition reaction when forming the tetramere. Hence the final goal could not be achieved. In the second project, two objectives were pursued: first, it was aimed to find a method to introduce the side chains of the quinolines on solid phase, which could save many synthetic steps in the preparation of the monomers. Additionally, a new coupling reaction should be developed in order to save the deprotection-step of the amine at the coupling on solid phase. As a result, especially for large foldamers, this would substantially reduce the risk of degeneration of the resin. For this coupling-reaction the azid-funtionalized monomer should be linked via a Staudingerreaction. The corresponding monomer was successfully synthesized. Also the first goal, the introduction of the side chain on the solid phase was successfully performed. Unfortunately, the achievement of both goals on the same synthetic route was not readily available. The monomer having no side chain is much more hydrophilic, a method of drying at an elevated temperature would be beneficial, in order to remove bound water. However, since the monomer also carries an azide, it would explosively decomposes at 130 °C, so this was not possible. However, even small traces of moisture would affect the Staudinger-Reaction. Therefore, the second objective of the project could not be realized. In the third project, the preparation of a large foldamer library, for analysis of the binding affinity for IL-4 was performed. It should consist of 48 hexamers, wherein three monomers on the side chains should be varied to accommodate a wide variety of interactions. For this purpose, four different monomers were synthesized, which contained an aromatic, a polar, an anionic or a cationic sidechain. Similar to the synthesis of amino acid sequences a method has been developed and successfully applied for the coupling of the foldamers. Thus all 48 foldamers were successfully synthesized and 46 of them could be purified in sufficient quantities for the study on IL-4. However, no results on the inhibitory properties compared to IL -4 were known currently. Since structurally very similar foldamers have shown inhibition of IL -4, the newly created library is likely to be active. The fourth project was carried out within the framework of the SFB 630. Therefore some of the foldamers originally produced for other projects were selected, partially deprotected or reduced at the nitro group and then tested for their activity against Leishmania and Trypanosoma. These compounds were not effective against Leishmania and Trypanosoma which might be due to the substitution pattern of the quinolines. However, in the investigated concentration range, no cytotoxicity occurred, which is an interesting piece of information for the use of foldamers and their components in biological systems. KW - Foldamere KW - Interleukin KW - Foldamers KW - Foldamer KW - abiotische Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-96486 ER - TY - JOUR A1 - Luxenhofer, Robert A1 - Fetsch, Corinna T1 - Thermal Properties of Aliphatic Polypeptoids JF - Polymers N2 - A series of polypeptoid homopolymers bearing short (C1–C5) side chains of degrees of polymerization of 10–100 are studied with respect to thermal stability, glass transition and melting points. Thermogravimetric analysis of polypeptoids suggests stability to >200 °C. The study of the glass transition temperatures by differential scanning calorimetry revealed two dependencies. On the one hand an extension of the side chain by constant degree of polymerization decrease the glass transition temperatures (Tg) and on the other hand a raise of the degree of polymerization by constant side chain length leads to an increase of the Tg to a constant value. Melting points were observed for polypeptoids with a side chain comprising not less than three methyl carbon atoms. X-ray diffraction of polysarcosine and poly(N-ethylglycine) corroborates the observed lack of melting points and thus, their amorphous nature. Diffractograms of the other investigated polypeptoids imply that crystalline domains exist in the polymer powder. KW - peptoid KW - biomaterials KW - glass transition temperature KW - DSC KW - TGA KW - XRD Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-96333 ER - TY - THES A1 - Bissinger, Philipp T1 - Synthese, Struktur und Reaktivität Basen-stabilisierter Borane und Diborene T1 - Synthesis, Structure and Reactivity of Base Stabilized Boranes and Diborenes N2 - Umsetzungen N-heterocyclischer Carbene mit Boranen führen zur Bildung von „Lewis-Säure-Base-Addukten“. In Abhängigkeit des Substitutionsmusters der eingesetzten Borane bzw. Carbene eignen sich die erhaltenen Addukte als Ausgangsverbindungen zur Realisierung verschiedener Strukturmotive. Mit geeigneten Übergangsmetallfragmenten gelingt die Darstellung von sigma-Boran-Komplexen bzw. Basen-stabilisierter Boryl-Komplexe, welche mittels spektroskopischer Methoden sowohl im Festkörper, als auch in Lösung untersucht wurden. Ebenfalls gelingt die Synthese Basen-stabilisierter Borirane und einer tetraedrischen Borid-Spezies. Zudem wird ein selektiver Zugang zu Basen-stabilisierten Diborenen entwickelt, wobei deren Bindungssituation und Reaktivität im Detail diskutiert wird. So kann das B=B-Fragment in polymere Spezies eingebunden werden oder als Ligand an Übergangsmetalle koordinieren. N2 - Reaction of boranes with N-heterocyclic carbenes results in the formation of „Lewis-acid-base-adducts“. Depending on the substitution pattern of the boranes and carbenes, respectively, these adducts represent versatile starting materials for the realization of a diversity of different structural motifs. Treatment with suitable transition-metal fragments for instance afforded sigma-borane complexes and base-stabilized boryl complexes. These species are characterized in the solid state by X-ray diffraction, as well as by spectroscopy in solution. In addition, the synthesis of base-stabilized boriranes and a tetrahedral boride species is described. Moreover, a selective approach for the synthesis of base-stabilized diborenes is developed and their bonding situation and reactivity is studied in detail. Thus, the B=B moiety can be incorporated into polymeric structures or act as a ligand in the coordination sphere of transition-metals. KW - Borane KW - Carbene KW - Lumineszenz KW - Polymere KW - boron KW - inorganic chemistry KW - carbenes KW - luminescence KW - polymers KW - Bor KW - Anorganische Chemie Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-79144 ER - TY - THES A1 - Tischer, Maximilian T1 - Bisquartäre Bisnaphthalimide - Neue Wirkstoffe gegen Infektionskrankheiten T1 - Bisquaternary Bisnaphthalimides - new active compounds against infectious diseases N2 - Die vorliegende Arbeit, die im Rahmen des SFB 630 „Erkennung, Gewinnung und funktiona-le Analyse von Wirkstoffen gegen Infektionskrankheiten“ erstellt worden ist, beschäftigt sich mit der Entwicklung und Synthese der bisquartären Bisnaphthalimide und deren antimikro-biellen Eigenschaften, speziell gegen Erreger tropischer Infektionskrankheiten, wie Plasmo-dien und Trypanosomen aber auch Bakterien wie Staphylococcus aureus. Erste Testungen einer kleinen Bibliothek verschiedener mono- und bisquartärer Phthal- und Naphthalimide im SFB 630 offenbarten deren antimikrobielles Potenzial. Daher war es das Hauptziel dieser Arbeit, durch systematische Variation der verschiedenen Strukturbestandteile diese Bibliothek zu erweitern. Dazu mussten zuerst die entsprechenden Naphthalin-1,8-dicarbonsäure-Anhydride hergestellt werden. Im nächsten Schritt wurden diese mit einem N,N-Dimethylaminopropylamin-Derivat zum Imid kondensiert und abschließend mit einem Alkyl-Linker zur bisquartären Verbindung alkyliert. So konnte die Bibliothek um 25 Verbin-dungen erweitert werden. Dabei umfassten die Variationen die Alkylkettenlänge zwischen den quartären Stickstoffen mit 3–14 Methylen-Einheiten, das aromatische Substitutionsmuster mit Amino- bzw. Nitrogruppen und symmetrische, wie asymmetrische Bisnaphthalimide. Durch anschließende antimikrobielle Testung und qualitativen Vergleich der ermittelten IC50-Werte konnten verschiedene strukturelle Merkmale der Bisnaphthalimide identifiziert werden, die einen positiven Einfluss auf die Aktivität gegen den untersuchten Mikroorganismus haben. N2 - The present work focuses on the design and synthesis of bisquaternary bisnaphthalimides and their antimicrobial properties, esp. against causative agents of tropical infectious diseases like Plasmodia or Trypanosoma but also bacteria like Staphylococcus aureus. The work was sup-ported by the SFB 630 “Recognition, Preparation and functional Analysis of Agents against Infectious Diseases”. First tests of a small compound library, consisting of several mono- and bisquaternary phthal- and naphthalimides, revealed their antimicrobial potential. Hence, it was the primary purpose of this work to broaden this library through systematical structural variations. Therefor the corresponding naphthalic anhydrides had to be synthesized. In the next step the anhydrides were condensed to the corresponding imide by reaction with an N,N-dimethylaminopropyl-amine derivative. The obtained naphthaimides were finally alkylated by means of α,ω-dihaloalkane to give the bisquaternary compound. The so achieved variations included the length of the alkyl-chain linker (C3–C14), the aromatic substitution pattern (nitro- and amino groups) and, symmetrical as well as unsymmetrical bisnaphthalimides. Subsequently, these compounds were tested against the aforementioned microorganisms. By comparing of the determined IC50-values several structural characteristics could be identified which are important to the antimicrobial activity. KW - Ammoniumverbindungen KW - Infektionskrankheit KW - Antibiotikum KW - Malaria KW - Staphylococcus KW - Schlafkrankheit KW - Naphthalimide KW - ammonium compounds KW - infectious disease KW - antibiotic KW - malaria Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-78527 ER - TY - THES A1 - Büttner, Tobias T1 - Totalsynthese mono- und dimerer Naphthylisochinolin-Alkaloide sowie Isolierung acetogeniner Sekundärmetabolite aus Wurzelkulturen von Triphyophyllum peltatum T1 - Total Synthesis of Mono- and Dimeric Naphthylisoquinoline Alkaloids and Isolation of Acetogenic Secondary Metabolites from Root Cultures of Triphyophyllum peltatum N2 - Die paläotropischen Pflanzenfamilien der Ancistrocladaceae und Dioncophyllaceae sind die bisher einzig bekannten Produzenten von Naphthylisochinolin-Alkaloiden. Diese spezielle Klasse acetogeniner Sekundärmetabolite weist durch die verschiedenen Kupplungspositionen der beiden namensgebenden Molekülbausteine eine breite strukturelle Diversität auf und zeichnet sich durch vielfältige pharmakologische Wirksamkeiten, z.B. antiplasmodiale, antileishmaniale oder antitrypanosomale Aktivitäten, aus. Zur Synthese dieser Naturstoffe wurde im Arbeitskreis Bringmann eigens eine Methodik entwickelt, das Lacton -Konzept. Diese Methode erlaubt durch eine Vorfixierung der beiden Molekülhälften durch eine Esterbrücke, anschließender intramolekularer Kupplungsreaktion und der stereoselektiven Öffnung des erhaltenen Lactons den atropselektiven Aufbau der Naphthylisochinoline. Als Ziele dieser Arbeit ergaben sich somit die Synthese pharmakologisch und strukturell interessanter Naphthylisochinolin-Alkaloide mittels des Lacton-Konzepts sowie die Isolierung und Strukturaufklärung weiterer Sekundärmetabolite aus Triphyophyllum peltatum (Dioncophyllaceae), welche anschließend auf ihre Bioaktivität hin untersucht werden sollten, um potenziell neue Leitstrukturen für neue Wirkstoffe zu finden. N2 - The paleotropical plant families of the Dioncophyllaceae and Ancitrocladaceae are the only known producers of naphthylisoquinoline alkaloids. This special class of acetogenic secondary metabolites shows a broad structural diversity - due to the different coupling sites of their molecular building blocks - and displays multifaceted pharmacological properties, e.g. antiplasmodial, antileishmanial and antitrypanosomal activities. For the synthesis of these natural products, a special method was elaborated in the bringmann working group, the lactone concept. This method permits the atroposelective synthesis of naphthylisoquinolines by prefixation of the two molecular halves via an ester bridge, subsequent intramolecular coupling, and stereoselective opening of the resulting lactone. Therefore, the main goals of this thesis were the synthesis of pharmacologically and structurally interesting naphthylisoquinoline alkaloids by using the lactone concept as well as the isolation and structural elucidation of further secondary metabolites from Triphyophyllum peltatum (Dioncophyllaceae) and the investigation of their bioactivities to possibly find new lead structures for new active agents. KW - Naphthylisochinolinalkaloide KW - Sekundärmetabolit KW - Triphyophyllum peltatum KW - Naphthylisochinoline KW - Organische Synthese KW - Malaria KW - Strukturaufklärung KW - Naphthylisoquinolines KW - Organic Synthesis KW - Malaria KW - Structure Elucidation Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-77371 ER - TY - THES A1 - Ertler, Daniel T1 - Untersuchungen zur Synthese und Reaktivität NHC-stabilisierter Kobaltkomplexe T1 - Investigations to the Synthesis and the Reactivity of NHC-stabilized Cobalt Complexes N2 - Die Arbeit befasst sich mit der Synthese verschiedener NHC-substituierter Kobaltkomplexe, sowie mit deren Anwendung in verschiedenen Bindungs-Aktivierungsreaktionen und in katalytischen Umsetzungen. N2 - This thesis deals with the synthesis of different NHC-stabilized cobalt complexes as well as with their use in different bond-activation reactions and in catalytic transformations. KW - Kobaltkomplex KW - Heterozyklisches Carbene-N KW - Aktivierung KW - Kobaltkomplex KW - N-heterozyklisches Carben KW - Bindungsaktivierung KW - cobalt complexes KW - N-heterocyclic carbene KW - bond activation Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-78409 ER - TY - THES A1 - Mager, Julian T1 - Synthese, Struktur und Reaktivität neuer [n]Metallocenophane T1 - Synthesis, Structure and Reactivity of new [n]Metallocenophanes N2 - Das Ziel dieser Arbeit bestand in der Synthese und Charakterisierung neuer Metallocenophane mit Sila-, Bora- und Stannabrücken. Sowohl für die Synthese über 1,1'-dimetallierte Metallocene als auch für die Synthese über die sogenannte flytrap-Methode sind dihalogenierte Brücken erforderlich. Für die Synthese neuer Trisilametallocenophane wurde deshalb eine verbesserte Synthese für 1,3-Diphenyl- und 1,3-Dichlorotrisilane erarbeitet. Die für die flytrap-Methode benötigten Liganden konnten aus 1,3-Dichloro-2,2-diisopropyltrisilan durch die Umsetzung mit den lithiierten Ringsystemen Lithiumindenid, Lithiumfluorenid und Lithiumoctafluorenid erhalten werden. Die dadurch dargestellten, zweifach arylsubstituierten Trisilane konnten anschließend erfolgreich mit BuLi zweifach lithiiert werden Das für die Darstellung von Triborametallocenophanen benötigte 1,3-Dibromo-1,2,3-tris(dimethylamino)triboran(5) sowie dessen Vorstufe 1,1,2,3,3-Pentakis-(dimethylamino)triboran(5) wurde über die bekannte Syntheseroute von Nöth et al. dargestellt. Durch eine Verbesserung der Reaktionsbedingungen konnten die Ausbeuten von 23% auf 36% bzw. auf 71% erhöht werden. Außerdem wurde eine Einkristallröntgenstrukturanalyse erhalten. Metallocenophane der 8. Gruppe werden meist durch Reaktion der 1,1'-dilithiierten Metallocenene mit dihalogenierten Brücken dargestellt. Um die Synthese von Rutheno- und Osmocenophanen zu ermöglichen, wurden Ruthenocen und Osmocen mit BuLi und pmdta als Hilfsbase lithiiert und erstmals als Feststoffe isoliert. Diese wurden mittels NMR-Spektroskopie und Einkristallröntgenstrukturanalyse untersucht, wodurch gezeigt wurde, dass sie wie 1,1'-Dilithioferrocen und 1,1'-Dilithometalloarenophane im Feststoff als dimere Verbindungen vorliegen. Aus thf konnte zusätzlich die Einkristallröntgenstrukturanalyse des thf-stabilisierten 1,1'-Dilithioruthenocen-Dimers erhalten werden Mit den in dieser Arbeit synthetisierten 1,3-Dichlorotrisilanen und 1,1'-Dilithioferrocen wurden die entsprechenden Trisilaferrocenophane synthetisiert und mittels NMR-Spektroskopie untersucht. Von der iPropyl-substituierten Verbindung konnte zusätzlich die erste Einkristallröntgenstrukturanalyse eines Trisilaferrocenophans erhalten werden Durch eine Umsetzung von 1,1‘-Dilithioruthenocen und –osmocen mit dem Diisopropyltrisilan konnten die ersten Trisilametallocenophane von Ruthenium und Osmium dargestellt werden. Durch die Umsetzung von 1,1‘-Dilithioosmocen mit Tetramethyldichlorodisilan gelang die Darstellung des ersten Osmocenophans mit einer zweiatomigen Brücke. Von Tetramethyldisilaosmocenophan konnte eine Einkristallröntgenstrukturanalyse erhalten werden. Die Syntheseroute von Tetra-tert-butyldistannaferrocenophan von Braunschweig et al. konnte erfolgreich auf die Synthese der Ruthenium- und Osmiumanaloga übertragen werden. Die zinnverbrückten Metallocenophane konnten NMR-spektroskopisch und durch eine Einkristallröntgenstrukturanalyse charakterisiert werden. Die von Wrackmeyer et al. und Braunschweig et al. bekannte Insertion von Chalkogenen in die Zinn-Zinn-Bindung konnte ebenfalls für die Verbindungen gezeigt werden. Dabei konnte eine deutliche Verkürzung der Reaktionszeit von 10 d auf 1 d durch die Zugabe von einem Äquivalent pmdta zur Reaktionsmischung erreicht werden. Mit der Ligandenvorstufe 1,2-Bis(lithio-cyclopentadienid)-1,1,2,2-tetra-tert-butyldistannan konnten über die flytrap-Methode die Distannametallocenophane von Cobalt und Nickel synthetisiert werden. Zudem konnten beide Verbindungen mit Ferroceniumhexafluorophosphat einfach oxidiert werden. Die beiden 19-Valenzelektronenverbindungen wurden mittels ESR-Spektroskopie untersucht. Von beiden Cobaltocenophanen sowie vom Nickelocenophan konnte eine Einkristallröntgenstrukturanalyse erhalten werden. N2 - The aim of this work consisted in the synthesis and characterization of new metallocenophanes with sila-, bora-, and stanna-bridges. Dihalogenated bridges are necessary both for the synthesis via 1,1’-dimetalated metallocenes and for the synthesis via the so-called flytrap method. Therefore, the first step consisted in the development of an improved synthetic procedure for the synthesis of 1,3-diphenyl-, and 1,3-dichlorotrisilanes. The ligands necessary for the flytrap method were obtained by reacting 1,3-dichloro-2,2-diisoporpltrisilan with the lithiated ring systems lithium indenide, lithium fluorenide, and lithium octafluorenide. Subsequently, a twofold lithiation of these molecules was carried out successfully with BuLi. 1,3-Dibromo-1,2,3-tris(dimethylamino)triborane(5), which is necessary for the synthesis of triborametallocenophanes, and its precursor 1,1,2,3,3,-pentakis(dimethylamino)-triborane(5) were synthesised via the synthetic procedure of Nöth et al.. By adjusting the reaction parameters, the yields were improved from 23% to36% and to 71%. Additionally, a solid state structure was obtained. Metallocenophanes of group 8 are generally synthesised by reacting 1,1'-dilithiated metallocenes with dihalogenated bridges. To achieve the synthesis of ruthenocenophanes and osmocenophanes, ruthenocene and osmocene were lithiated with BuLi and pmdta and isolated for the first time as solids. These were analysed via NMR spectroscopy and molecular structure analysis. This showed that both are dimers in the solid state, similar to 1,1'-dilithioferrocene and 1,1'-dilithiometalloarenophane. Additionally, the solid state structure of the thf-stabilised 1,1'-dilithioruthenocene dimer was obtained. Using the trisilanes and 1,1’-dilithioferrocene, new trisilaferrocenophanes were synthesised and analysed via NMR spectroscopy. Additionally, the first example of a crystal structure analysis of a trisilaferrocenophane was obtained. By reacting 1,1’-dilithioruthenocene and -osmocene with diisopropyltrisilane, the first trisilametallocenophanes of ruthenium and osmium were obtained. The reaction of 1,1’-dilithioosmocene with Me4Si2Cl2 resulted in the first osmocenophane with a diatomic bridge Also, a crystal structure analysis was obtained. The earlier synthesis of tetra-tert-butyldistannaferrocenophane by Braunschweig et al. was successfully transferred to the synthesis of the ruthenium and osmium analogues. The tin-bridged metallocenophanes were characterised by NMR spectroscopy and molecular structure analysis. The insertion of chalcogens into the tin-tin bond, previously reported by Wrackmeyer et al. and Braunschweig et al. was also shown. By adding one equivalent of pmdta to the reaction mixture, the reaction time was shortened significantly from 10 d to less than1 d. Using the ligand precursor 1,2-bis(lithio-cyclopentadienide)-1,1,2,2-tetra-tert-butyldistannane and the flytrap method, the distannametallocenophanes of cobalt and nickel were synthesised. Additionally, both compounds were oxidised by one electron using ferrocenium hexafluorophosphate. The 19 valence electron compounds were analysed via ESR spectroscopy. Crystal structure analyses were obtained from both cobaltocenophanes as well as the nickelocenophane. KW - Metallocene KW - Cyclophane KW - Übergangsmetallorganische Verbindungen KW - Metallocenophane KW - Übergangsmetalle KW - ansa KW - Metallorganic KW - Osmium KW - Ruthenium KW - Esien KW - Cobalt KW - Nickel KW - Zinn KW - Silicium KW - Bor KW - Metallocenophanes KW - Transition Metals KW - ansa KW - metal organic Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-78384 ER -