TY - JOUR A1 - Haider, Malik Salman A1 - Ahmad, Taufiq A1 - Yang, Mengshi A1 - Hu, Chen A1 - Hahn, Lukas A1 - Stahlhut, Philipp A1 - Groll, Jürgen A1 - Luxenhofer, Robert T1 - Tuning the thermogelation and rheology of poly(2-oxazoline)/poly(2-oxazine)s based thermosensitive hydrogels for 3D bioprinting JF - Gels N2 - As one kind of “smart” material, thermogelling polymers find applications in biofabrication, drug delivery and regenerative medicine. In this work, we report a thermosensitive poly(2-oxazoline)/poly(2-oxazine) based diblock copolymer comprising thermosensitive/moderately hydrophobic poly(2-N-propyl-2-oxazine) (pPrOzi) and thermosensitive/moderately hydrophilic poly(2-ethyl-2-oxazoline) (pEtOx). Hydrogels were only formed when block length exceeded certain length (≈100 repeat units). The tube inversion and rheological tests showed that the material has then a reversible sol-gel transition above 25 wt.% concentration. Rheological tests further revealed a gel strength around 3 kPa, high shear thinning property and rapid shear recovery after stress, which are highly desirable properties for extrusion based three-dimensional (3D) (bio) printing. Attributed to the rheology profile, well resolved printability and high stackability (with added laponite) was also possible. (Cryo) scanning electron microscopy exhibited a highly porous, interconnected, 3D network. The sol-state at lower temperatures (in ice bath) facilitated the homogeneous distribution of (fluorescently labelled) human adipose derived stem cells (hADSCs) in the hydrogel matrix. Post-printing live/dead assays revealed that the hADSCs encapsulated within the hydrogel remained viable (≈97%). This thermoreversible and (bio) printable hydrogel demonstrated promising properties for use in tissue engineering applications. KW - poly(2-ethyl-2-oxazoline) KW - shear thinning KW - shape fidelity KW - cyto-compatibility KW - bio-printability Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-241781 SN - 2310-2861 VL - 7 IS - 3 ER - TY - JOUR A1 - Lübtow, Michael M. A1 - Marciniak, Henning A1 - Schmiedel, Alexander A1 - Roos, Markus A1 - Lambert, Christoph A1 - Luxenhofer, Robert T1 - Ultra-high to ultra-low drug loaded micelles: Probing host-guest interactions by fluorescence spectroscopy JF - Chemistry - A European Journal N2 - Polymer micelles are an attractive means to solubilize water insoluble compounds such as drugs. Drug loading, formulations stability and control over drug release are crucial factors for drug‐loaded polymer micelles. The interactions between the polymeric host and the guest molecules are considered critical to control these factors but typically barely understood. Here, we compare two isomeric polymer micelles, one of which enables ultra‐high curcumin loading exceeding 50 wt.%, while the other allows a drug loading of only 25 wt.%. In the low capacity micelles, steady‐state fluorescence revealed a very unusual feature of curcumin fluorescence, a high energy emission at 510 nm. Time‐resolved fluorescence upconversion showed that the fluorescence life time of the corresponding species is too short in the high‐capacity micelles, preventing an observable emission in steady‐state. Therefore, contrary to common perception, stronger interactions between host and guest can be detrimental to the drug loading in polymer micelles. KW - curcumin KW - drug delivery KW - fluorenscence KW - poly(2-oxazine) KW - pol(2-oxazoline) KW - Polymer-drug interaction KW - upconversion Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-206128 VL - 25 IS - 54 ER - TY - THES A1 - Müller, Melanie T1 - Untersuchung von Grenzflächenreaktionen von kristallisierenden Glasloten bei der Fügung von Hochtemperaturbrennstoffzellen T1 - Investigation of interfacial reactions of crystallizing glass sealants at sealing of solid oxide fuel cells N2 - Für die Fügung der Interkonnektoren einer Hochtemperaturbrennstoffzelle wurden in der hier vorliegenden Arbeit glaskeramische Lote entwickelt und untersucht. Es konnte ein hochviskoses Glas gefunden werden, das trotz fehlendem Erweichen bei der Fügung eine stabile, gasdichte und elektrisch isolierende glaskeramische Fügung ausbildet. Auch während des Betriebs kommt es zu keinem Erweichen der Fügung. Weiter treten keine feststellbaren Reaktionen mit den potentiellen Reaktionspartnern, den Stahlelementen, auf. Es konnte eine Korrelation dieses Reaktionsverhaltens mit dem Kristallisationsverhalten der Glaskeramik gefunden werden. Das Verhalten des Glaslotes wurde über mehrere tausend Stunden unter Betriebsbedingungen beziehungsweise betriebsimulierenden Bedingungen untersucht. Dabei konnte die Kristallisationsentwicklung beschrieben werden. Ein weiterer Aspekt der Arbeit war die Untersuchung des Einflusses der einzelnen Faktoren, denen ein Glaslot während seines Einsatzes von der Fügung bis zum Betrieb ausgesetzt ist, wie die Fügetemperatur, die Viskosität der eingesetzten glasbildenden Schmelze oder die Dualgasatmosphäre im Betrieb, auf das Gefüge und die Diffusion. Hierbei konnte gezeigt werden, dass die Fügetemperatur mit Abstand den größten Einfluss auf die Stabilität der Glaslotschicht hat. Diese bedingt nicht nur die Kinetik des Fließens und die Benetzung des Stahls durch das Glas, sondern vor allem, welche Kristallphasen gebildet werden und wie das finale Gefüge im Hinblick auf Kristallitgröße und –verteilung aussieht. So kommt es bei höheren Temperaturen zu einem größeren Restglasphasenanteil und einem geringeren Kristallitanteil, was wiederum die Diffusion der Stahlelemente in die Glaslotschicht begünstigt. N2 - This work describes the development and analysis of new glass ceramic sealants for the use in solid oxide fuel cells. The sealant is applied to the sealing area of metallic interconnectors. The developed sealant has a high viscosity in such a way as to keep its geometric form stable during the sealing process and during the operation of a solid oxide fuel cell. This sealant enables a stable, gastight and electrically insulating sealing. There are no reactions with the contacting materials, the elements of the steel, even after extended time under operation or operation-like conditions. This stability can be explained by the crystallization behaviour of the glass ceramic which forms an interface layer. This behaviour was monitored over a few thousand hours. Furthermore, the parameters, which have a potential influence on the glass ceramic during the whole life cycle, the sealing and the operation, were examined. The parameters which were investigated were in particular the sealing temperature, the viscosity of the glass, the operation time and the dual gas atmosphere. The sealing temperature has the most significant effect on the formation of the glass ceramic. It defines the formation of the crystallites, the type as well as the size and allocation of the crystallites. At a higher sealing temperature, for example, less crystallites and a larger glassy phase is formed. This effect can lead to an increase of the diffusion processes. Another relevant parameter is the viscosity of the glass, as a low viscosity increases the diffusion. After extended operation time, a growth of the crystallites and a decrease of the amount of the glassy phase was observed. This was indifferent to the other occuring factors like the applied voltage or the dual gas atmosphere. In conclusion, the newly developed glass ceramic sealant paves a way for the use of SOFC, in particular for mobile applications, where the external mechanical stresses cause higher requirements on the sealant. KW - Hochtemperaturbrennstoffzelle KW - Glaslot KW - SOFC Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-296871 ER - TY - THES A1 - Collin [geb. Trötschel], Daniela T1 - Untersuchungen zu photostrukturierbaren piezo- und ferroelektrischen Dünnschichten T1 - Investigations concerning photopatternable piezo- and ferroelectrical thin-films N2 - Im Rahmen der vorliegenden Arbeit wurde untersucht, wie sich organisch polymerisierbare Titan(IV)- und Zirkonium(IV)komplexe, die bei der Synthese anorganisch-organischer Hybrid-polymere verwendet werden, in Precursor-Solen für anorganische Beschichtungen verhalten. Dabei sollte ein Konzept zur Herstellung photochemisch strukturierter, anorganischer Dünnschichten erarbeitet werden. Als Beispiel für das anorganische Dünnschichtmaterial wurde Bleizirkonattitanat (PZT) und für die polymerisierbaren Liganden Methacrylsäure gewählt. Der Schwerpunkt der Arbeit lag dabei besonders auf den Untersuchungen der photochemischen Polymerisation mittels UV-lithographischer und Mehrphotonenpolymerisation sowie der in situ Untersuchung während der Pyrolyse des polymerisierten Materials und der Reaktion zur anorganischen Dünnschicht. Der Prozess zur Herstellung photostrukturierter, anorganischer Dünnschichten kann in zwei Schritte eingeteilt werden. Nach der Synthese des Precursor-Sols erfolgten zunächst die licht-induzierte organische Polymerisation und die Entfernung der nicht polymerisierten Bereiche mit Hilfe eines Entwicklerbads. Im Anschluss daran wurden im zweiten Schritt die organischen Bestandteile durch eine thermische Behandlung entfernt und die Reaktion zum anorganischen Oxidmaterial induziert. Die homogensten Schichten wurden dabei mit einem n Butanol-basierten, methacrylat¬funktionalisierten PZT-Sol mit 25 Gew. % Feststoffgehalt auf Stahlsubstraten bei Pyrolyse¬bedingungen ab 500 bis 700 °C mit einer Heizrate von 5 K/min erreicht. An diesen Schichten konnte ferroelektrisches Verhalten nachgewiesen werden. Allerdings reichen die Eigenschaften noch nicht an in der Literatur beschrieben ferro- und piezoelektrische Dünnschichten heran, die ebenfalls aus PZT-Solen hergestellt wurden. Dies liegt zum einen an den zu geringen Schichtdicken und der damit verbundenen erhöhten Durchschlagsgefahr dieser Sol-Gel-basierten PZT-Schichten. Zum anderen reduzieren Grenzflächenreaktionen des chromhaltigen Substrats und der PZT-Solschicht zu Pb2(CrO4)O sehr drastisch die ferroelektrischen Eigenschaften, indem sich nicht-ferroelelektrische Oxidschichten mit niedrigen Permittivitäten bilden und die Beweglichkeit der Domänenwände durch Diffusion von Cr3+-Akzeptorionen in die PZT-Schicht verringert wird. Zunächst wurde die PZT-Solsynthese untersucht. Dabei konnte gezeigt werden, dass die Nebenproduktbildung von verschiedenen Estern vermieden werden kann, wenn die leicht flüchtigen Bestandteile nach der Ligandenaustauschreaktion von Alkoxid gegen Methacrylsäure bei reduziertem Druck und damit verbundenen niedrigeren Reaktionstemperaturen, erfolgte. Die Bindung der Methacrylatliganden ist in jedem Fall bidentat. Bei den n Butanol-basierten PZT-Solen konnte trotz höherer Siedetemperatur und niedrigerem Dampfdruck ein größerer Anteil an Alkohol entfernt werden, als bei n-Propanol-basierten PZT-Solen. Dies wurde auf den etwas höheren +I Effekt des n Butanols und in der Folge der bevorzugten Ligandenaustauschreaktion von Methacryl¬säure gegen den n Butanol im Vergleich zu n Propanol zurückgeführt. Die Größe der PZT-Cluster war langzeitstabil, reproduzierbar herstellbar und betrug ca. 2,0 – 2,5 nm. Aus der Partikelgröße und dem spektros¬kopischen Nachweis von Metalloxobindungen konnte ein Strukturvorschlag basierend auf den zugrundeliegenden Titan- und Zirkoniumkomplexen erstellt werden. Dabei bilden MO6 Komplexe das Grundgerüst stäbchenförmiger, heterometallischer Cluster. Die polymerisierbaren Methacrylatliganden befinden sich auf der Oberfläche und sind gut zugänglich für die Polymerisationsreaktion. Die mittlere Anzahl an Methacrylatliganden pro PZT-Cluster wurde zu 5 - 25 je nach Gewichtung abgeschätzt. Bei der UV-lithographischen Strukturierung ergaben sich zwei unerwartete Effekte. Zum einen trat nach der Schichtherstellung eine reversible Trübung des PZT-Sols auf, welches auf konzentrations¬bedingte Phasenseparation zurückgeführt werden konnte. Zum anderen setzte sich unter N2 Atmosphäre die lichtinduzierte radikalische Kettenreaktion in den methacrylat-funktionalisierten PZT-Solschichten auch in die unbelichteten Bereiche fort. Dieser Effekt wird sonst in dieser Deutlichkeit nur von kationischen Polymerisationsreaktionen beobachtet und auf lange Radikal¬lebensdauern zurückgeführt und wurde mittels Photo-Differentialkalorimetrie weitergehend untersucht. Allerdings konnte aufgrund der Probengeometrie der Einfluss der Atmosphäre mit der Photo-DSC-Methode nicht eindeutig geklärt werden. Die Qualität der pyrolysierten PZT-Schichten konnte durch Variation der Feststoffgehalte und der Pyrolysebedingungen optimiert werden. So wurden durch die Verdünnung der PZT-Sole auf 25 Gew. % Feststoffgehalt bei ansonsten analogen Pyrolyse¬bedingungen dichtere und homogenere Schichten erhalten, wohingegen PZT-Solschichten mit einem Feststoffgehalt von 31 Gew.-% eine xerogelartige Struktur durch agglomerierte Partikel zeigten. Die untersuchten Substrate wiesen einen deutlichen Einfluss auf die nach der Pyrolyse erhaltenen PZT-Schichten auf. Unmetallisierte Silizium-Wafer eigneten sich zwar zur Untersuchung der UV-lithographischen Herstellung strukturierter Solschichten, bei der Pyrolyse bildeten sich jedoch unerwünschte Bleisilicat¬schmelzen, die der PZT-Bildung entgegen wirkten. Weiterhin wurden platinierten Silizium-Wafer mit Titanhaftvermittler¬schicht und SiO2-Sperrschicht verwendet. Diese Substrate zeigten eine durch die hohen Pyrolyse¬temperaturen induzierten Diffusion der Haftvermittlerschicht in die Platinmetallisierung und in der Folge eine Delamination aufgrund hoher Druckspannung in der PZT-Schicht, welche durch die Entfernung der organischen Bestandteile aus der Solschicht resultierte. In der Folge entstanden mechanisch instabile Proben. Die Delamination konnte durch Zwischensinterschritte bei 360 °C bzw. durch die Pyrolyse auf Heizplatten reduziert, jedoch nicht vollständig vermieden werden. Aus diesem Grund konnten keine ferroelektrischen Eigenschaften der PZT-Schichten auf diesen Substraten ermittelt werden. Lediglich auf Stahlsubstraten konnten elektrisch dichte Schichten hergestellt werden. Die Polymerisationsreaktion eines ausgesuchten PZT-Sols, welches bei den Strukturierungs- und Pyrolyseuntersuchungen die besten Ergebnisse zeigte, wurde näher untersucht, um ein Verständnis zu den ablaufenden Reaktionen zu erhalten. Die Reaktion zeigt den für radikalische Kettenpolymerisationen typischen Trommsdorf- bzw. Gel-Effekt. Durch die Verdünnung der PZT-Cluster konnten trotz hoher Anzahl an C=C-Bindungen pro Monomer, d. h. stark quervernetzender Spezies, sehr hohe Umsetzungsgrade erreicht werden. Die initiator¬gehalts-abhängige Steigerung der Reaktionsenthalpie während der Belichtung konnte mit steigenden Umsetzungs¬graden korreliert werden. Dieses Verhalten wird in der Literatur für eine Vielzahl an methacrylatbasierten Monomeren beschrieben. Der empirische Zusammenhang zwischen der Reaktionsrate und der Initiatorkonzentration konnte für das methacrylat¬funktionalisierte PZT-Sol zu bestimmt werden. Die Gesamtaktivierungenergie konnte ebenfalls in Abhängigkeit vom Reaktionsumsatz ermittelt werden. Die Polymerisation eines konzentrierten PZT-Sols mit difunktionellen Monomeren zeigte höhere Umsetzungsgrade als die entsprechenden Reinsubstanzen und ein späteres Eintreten des Gelpunkts. Dies wird zurückgeführt auf die niedrigere Viskosität sowie die geringere Molekülgröße des Reaktivverdünners und die in der Folge bessere Infiltration des durch das PZT-Sol aufgespannten Netzwerks mit zusätzlichen kleinen und beweglichen Monomeren. Da bei der thermischen Behandlung der polymerisierten PZT-Schichten die experimentellen Bedingungen, wie z. B. Heizrate oder Anfangstemperatur der Pyrolyse, einen signifikanten Einfluss besitzen, wurden energiedispersive in-situ-Röntgenbeugungsexperimente mit Hilfe von Synchrotron¬strahlung durch¬geführt. Hierbei konnte vor allem der Einfluss der organischen Polymerisation und der Anfangstemperatur der Pyrolyse auf die Phasenentwicklung des Precursor-Sols untersucht werden. Dabei zeigte sich besonders deutlich, dass die PZT-Bildungstemperatur durch die Belichtung der Probe und damit der Bildung des organischen Netzwerks steigt. Dies wird auf das starke organische Netzwerk und den erhöhten Energiebedarf zur Reorganisation zurückgeführt. Durch eine erhöhte Anfangstemperatur der Pyrolyse von 500 °C kann die in der Literatur beschriebene Verringerung der unerwünschten Pyrochlor-Phase beobachtet werden. Zudem ist die PZT-Bildungstemperatur hierbei niedriger als bei Pyrolysen ab Raumtemperatur. Dies wird mit einer durch den geringeren Anteil an Pyrochlor-Phase erhöhten Triebkraft zur PZT-Bildung erklärt. Die konsekutive Phasenumwandlung von Pyrochlor in die erwünschte PZT-Phase ist bei Pyrolysen ab Raumtemperatur später abgeschlossen als bei Pyrolysen ab 500 °C. Dies kann mit dem geringeren Anteil an Pyrochlor-Phase erklärt werden, da sich ab 500 °C bereits die PZT-Phase zu bilden beginnt. Der Vergleich der Halbwertsbreiten des intensitätsstarken Reflexes bei 31 ° zeigte, dass die Belichtung der Solschichten zu größeren Kristalliten führt, was auf eine niedrigere Nukleationsrate während der Kristallisation zurückzuführen ist. Bei der Auswertung und Diskussion der Ergebnisse der im Rahmen dieser Arbeit untersuchten Thematik ergaben sich einige Ansatzpunkte für weitere Untersuchungen, die jedoch nicht im zeitlichen und thematischen Rahmen dieser Arbeit betrachtet werden konnten. So wäre es interessant weitere Substrate auf ihre Eignung bei der, für die Herstellung strukturierten PZT-Schichten notwendigen, hohen thermischen Belastung zu testen, da die hier untersuchten platinierten Silizium-Wafer bzw. die Stahlsubstrate deutliche Nachteile zeigten. Des Weiteren können neben den hier behandelten polymerisierbaren Carbonsäureliganden weitere mehrzähnige Liganden und dessen Einfluss auf die Precursormaterialien für die Herstellung strukturierter anorganischer Schichten untersucht werden. β-Diketone, Aminoalkohole und auch Phosphonate bilden ebenfalls stabile Metall-Ligand-Bindungen und könnten so die Integration polymerisierbarer Gruppen in die PZT-Cluster analog zu der im Rahmen dieser Arbeit verwendeten Carbonsäure ermöglichen. Das hier erarbeitete Konzept könnte neben den untersuchten ferroelektrischen Schichtmaterialien ebenfalls auf andere dielektrische oder magnetische Materialklassen, wie z. B. Bariumtitanat oder Magnetit übertragen werden. Die Herstellung photostrukturierbarer anorganischer Schichten durch den Einbau polymerisierbarer Liganden eignet sich für zahlreiche Materialklassen, die über flüssige Sol-Gel-Vorstufen synthetisiert werden können. Darüber hinaus können weitere Pyrolysebedingungen mit den hier vorgestellten Analysemethoden untersucht werden. So könnten z. B. verschiedene Atmosphären oder unterschiedliche Heizraten innerhalb eines Pyrolysezyklus variiert werden, um ihren Einfluss auf die Herstellung rissfreier und phasenreiner Schichten zu untersuchen. Dazu müsste der hier vorgestellte experimentelle Aufbau dahingehend erweitert werden, dass eine Gaszufuhr während der Pyrolyse möglich ist. N2 - The broad objective of this study was to investigate the properties of photopolymerizable precursor sols using organically polymerizable titan(IV) and zirconium(IV) complexes, which are commonly used in the synthesis of inorganic-organic hybrid polymers. With the help of these complexes an approach to the preparation of photochemically patterned, inorganic thin films was developed. Lead zirconate titanate (PZT) was chosen as the inorganic material. The polymerizable moiety was introduced into the precursor sol using methacrylic acid as the polymerizable ligand. Particular attention has been drawn to the investigation of the photochemical reaction of the precursor sol and on the in-situ analysis of the thermally induced conversion into the inorganic PZT thin film, respectively. The process for the preparation of photochemically patterned, inorganic thin films can be divided into two independent steps. These are, on the one hand, the light induced organic polymerization of the synthesized precursor sol and on the other hand, the thermal decomposition of the organic moieties along with the formation of crystalline PZT. Patterned PZT thin films were prepared, for example, using a methacrylated PZT-sol based on n butanol. The solid content of this precursor sol was set to 25 wt. % by diluting with high-boiling point organic solvents. The sol was spin-coated onto steel substrates, followed by the patterning process due to light-induced polymerization. After removal of the unexposed areas using a solvent developer, the pyrolysis reaction was started at 500 °C. The inorganic thin-film was obtained by further heating with a heating rate of 5 K/min to reach a final temperature of 700 °C. Although ferroelectric behavior was verified for these samples, their properties are still inferior compared to commonly prepared ferroelectric thin films. This has been attributed to several different reasons, such as low thickness of the thin film, the formation of undesired side-products and acceptor-doping due to ion diffusion out of the steel substrate, respectively. Firstly, there is an increased risk of electric breakdown within the PZT thin-films due to the low thickness of the films. Secondly, an undesired side-product (Pb2(CrO4)O) forms at the interface of the steel substrate and the PZT thin-film. This leads to a non-ferroelectic layer within the PZT, which drastically reduces the ferroelectric behavior. Finally, Cr3+ ions of the steel substrate can migrate into the PZT thin-film forming an acceptor doped material, which results in a reduced domain wall mobility. The synthesis of the PZT sol was investigated and it was shown that the formation of undesired ester by-products could be avoided, if the volatile products of the ligand exchange reaction of alcohol and methacrylic acid are distilled at reduced pressure, as lower distillation temperatures have to be applied. The coordination of the methacrylic acid ligand in the resulting complexes is bidentate. Although the boiling temperature of n butanol is higher and its vapor pressure is lower, a higher amount of alcohol can be removed during distillation in the case of n butanol based PZT sols compared to sols based on n propanol. This may be attributed to a favored ligand exchange reaction. The size of the PZT precursor cluster is is about 2,0 – 2,5 nm. The methacrylated PZT sol can be prepared with a high degree of reproducibility and is storage-stable over several months. Based on this particle size and the spectroscopic detection of metal oxo groups within the PZT precursor sol, a structure was proposed, which is made up of titan- and zirconium-containing MO6-complexes forming rod-like heterometallic clusters. The polymerizable methacrylic ligands are bound to the outer surface of the clusters and thus are susceptible to the polymerization reaction. The average number of methacrylic ligands per PZT sol cluster was estimated at 5 – 25 depending on the weighting. The UV lithography process was marked by two effects. On the one hand the spin-coated PZT precursor films featured a reversible hazing, which was attributed to a concentration dependent phase separation of the precursor. On the other hand, if the light exposure was performed under a constant stream of nitrogen, the radical polymerization reaction proceeded into the shadow areas of the mask. Usually, this behavior is limited to cationic polymerization and is attributed to long lifetimes of the reactive species. In Photo-DSC experiments, this effect is observed for the methacrylated PZT-sol, as well. However, due to the different sample setup the influence of the atmosphere could not be resolved with this Photo-DSC method. The quality of the pyrolyzed PZT thin films was optimized by variation of the solid content and by variation of the pyrolysis parameters. The methacrylated PZT sols with a solid content of 25 % lead to the formation of homogenous and dense thin-films, whereas the pyrolysis of PZT sols with a solid content of 31 % resulted in xerogel like morphology due to agglomeration of precursor particles. The substrates, used within this work, exerted a major influence on the PZT thin films. Pure silicon wafers were appropriate for the investigations concerning the UV lithography process or the polymerization reaction. However, during the thermal treatment of the PZT precursor thin film, the silicon substrate reacted with the sol forming undesired lead silicate meltings, which inhibited PZT formation. The platinized silicon wafers containing titan and silicon oxide sublayers also showed increased reaction during thermal annealing as the titan adhesion layer migrated into the platinum electrode. As a result, the compressive stress generated in the PZT thin-film due to the combustion of the organic residues could not be compensated by the remaining adhesion layer and, consequently, the platinum electrode delaminated. The resulting samples exhibited a very low mechanical stability. The delamination of the electrode layers was reduced by either intermediate annealing steps at 360 °C or by the application of hotplates instead of a furnace. However, a complete prevention of delamination was not achieved. Hence, due to the ensuing electric breakdown, no ferroelectric properties could be obtained from photochemically patterned PZT thin films on these platinized silicon substrates. Furthermore, the polymerization of the methacrylated PZT sol was investigated in order to obtain a better understanding of the reactions that take place. The light induced polymerization exhibited the Trommsdorf or gel effect, which is typical for radical chain reactions. After curing the resulting films showed very high conversion rates, when diluted in various solvents. This is obtained regardless of the high number of polymerizable C=C bonds per cluster, which can lead to highly branched networks in which the mobility of reactive moieties is usually reduced significantly even at low conversion rates. The increase in the reaction enthalpy depending on the content of UV initiator sufficiently correlates with increasing conversion rates. In literature, this behavior is reported for a number of methacrylate¬-based monomers. The empirical relation of the reaction rates and the concentration of UV initiator was determined as . The overall activation energy for the polymerization of the methacrylated PZT sol was calculated depending on the reaction conversion. Additionally, the copolymerization with difunctional monomers exhibited higher conversion rates than the pure monomers and the onset of the gel effect is delayed. Energy dispersive in-situ x-ray diffraction analyses using synchrotron radiation were performed to examine the influence of the different pyrolysis parameters, such as heating rate and starting temperature of the annealing step. It was observed, that the polymerization of the PZT precursor thin-films, and thus the formation of an organic network, resulted in an increase in the temperature needed for PZT formation. This effect was attributed to the strong covalent organic network, which had accumulated during polymerization, and thus an increased energy was needed for reorganization. By increasing the starting temperature of the annealing step to 500 °C, the reduced formation of undesired pyrochlore was observed, as previously reported in literature. Furthermore, the PZT formation temperature is lower compared to pyrolysis starting at room temperature. This was explained by an increased driving force for PZT crystallization due to a lower amount of pyrochlore phase. In addition, the consecutive phase transformation from pyrochlore into PZT was completed at lower temperatures, if the starting temperature was 500 °C. A comparison of the halfwidth of the PZT reflex at 31° revealed that the polymerized PZT thin films exhibited larger crystallite sizes compared to unexposed thin films. In addition to the higher formation temperature, this was accredited to a lower nucleation rate in the polymerized PZT precursor films. During the interpretation and discussion of the results of this thesis, a number of new and interesting aspects arose, which could not be dealt with within the framework of this study. Therefore, it would be interesting to investigate further substrates for their suitability within the PZT preparation process. The substrates used within this work exhibited a number of significant disadvantages, such as thermal instability and undesired reactions with the PZT precursor. Additionally, alongside the methacrylic ligand which was tested within this work, other polymerizable ligands may be used for the synthesis of photopatternable precursor sols. β diketones, amino alcohols and phosphonates also form stable metal ligand bonds, and thus could be used to introduce the polymerizable moiety. The resulting concept of polymerizable precursors for inorganic thin films might also be transferred to dielectric or magnetic material classes, such as barium titanate. In principle, this process is applicable for all materials that can be synthesized by liquid sol-gel precursors. Additionally, further parameters of the pyrolysis could be investigated with the in-situ x-ray diffraction method, which was used within this thesis. The influence of different annealing atmospheres or different heating rates could also be examined. For the variation of the reaction atmosphere, an adaption of the experimental setup would have to be realized first, which allows the gas supply. KW - Ultraviolett-Bestrahlung KW - Sol-Gel-Verfahren KW - Dünne Schicht KW - Photostrukturierung KW - Ferroelektrikum KW - PZT KW - Strukturierung Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-108422 ER - TY - THES A1 - Beyer, Matthias T1 - Untersuchungen zu photovernetzbaren und biokompatiblen (Hybrid-)Polymeren T1 - Investigations of photo-curable and biocompatible (hybrid) polymers N2 - Die Arbeit beschäftigte sich mit Untersuchungen zu photovernetzbaren und –strukturierbaren (Hybrid-)Polymeren, um Grundlagen für die Herstellung von Trägergerüststrukturen (Scaffolds) auf Basis photovernetzbarer (Hybrid-)Polymere zu legen und damit in der Zukunft patientenindividuelle medizinische Werkstücke, die beliebig durch Zwei-Photonen-Absorptionsprozesse in drei Dimensionen strukturierbar sind, für die Regenerative Medizin zu ermöglichen. Dafür wurden zunächst die zum Teil in der Literatur unbekannten unterschiedlichen Monomere Acr-1, MAcr-2, Acr-3, MAcr-4 und DiMAcr-5 synthetisiert. Dabei handelt es sich um einfache und gut vergleichbare organische (Meth-)Acrylat-Monomere, die mono- bzw. difunktional in ihren photochemisch reaktiven Gruppen sind. Die synthetisierten organischen Monomere Acr-3, MAcr-4 und DiMAcr-5 wurden in verschiedenen Verhältnissen mit dem anorganisch-organischen Methacrylat-basierten Hybridpolymers ORMOCER® I kombiniert. Die (Co-)Polymerisation der unterschiedlichen Formulierungen wurde in situ mittels UV-DSC-Untersuchung verfolgt. Dabei wurden bei diesen Untersuchungen zum Teil deutliche Unterschiede im Reaktionsverlauf der einzelnen Materialformulierungen festgestellt. So konnten zum Beispiel bei Monomermischungen ein schnellerer Polymerisationsverlauf sowie eine höhere maximale Polymerisationsrate als bei den jeweiligen Einzelkomponenten beobachtet werden (Synergieeffekt). Diese Beobachtungen wurden anhand der Monomerstruktur (unterschiedliche Diffusionsfähigkeiten im vergelten, aber noch nicht erstarrten System durch Mono- bzw. Difunktionalität) und der Art der funktionellen Gruppe (Acrylat- bzw. Methacrylatgruppe) erklärt. Weiterhin wurden der Einfluss des verwendeten Photoinitiators und dessen eingesetzte Konzentration auf die photochemisch-induzierte Copolymerisation eines ausgewählten Systems beleuchtet. Dazu wurden verschiedene Einflussfaktoren der Initiation betrachtet. Neben der eingesetzten Initiatorkonzentration spielen auch die Absorptionseigenschaften, die umgebende Matrix und die Initiatoreffizienz eine große Rolle für den Reaktionsverlauf der photochemischen Vernetzung. Weiterhin wurden die Photoinitiatoren in unterschiedlichen Konzentrationen eingesetzt, um die dadurch induzierte Veränderung des Reaktionsverlaufs zu betrachten. Aus den Einflüssen auf die Reaktionsverläufe konnte geschlossen werden, dass diese sowie auch die maximale Polymerisationsrate RP,max und damit die Reaktionskinetik nicht in jedem Fall linear mit der Initiatorkonzentration zunehmen muss. Erste generelle 2PP-Strukturierungen wurden zudem an ausgewählten Material-formulierungen durchgeführt. Dabei zeigte sich, dass alle Formulierungen bei bestimmten Parameterkombinationen aus Laserleistung und Schreibgeschwindigkeit mittels 2PP strukturiert werden konnten. Außerdem wurden bei den verschiedenen Formulierungen bei gleicher Parameterkombination unterschiedliche Strukturbreiten und damit erstmalig unterschiedliche Strukturvolumina beobachtet. Diese unterschiedlichen Volumina konnten erstmalig mit den unterschiedlichen Reaktionsverläufen der Materialformulierungen korreliert werden. Dabei zeigte sich, dass das chemische Wechselwirkungsvolumen von der Funktionalität der eingesetzten Materialkomponenten abhängig ist, da davon der Grad an Quervernetzung abhängt, der bestimmt, ob ausreichend vernetzte Voxel und Strukturen entstehen, die durch einen Entwicklungsschritt nicht mehr entfernt werden. Im zweiten Teil der Arbeit wurde ein biokompatibles und photostrukturierbares Hybridpolymer (RENACER® MB-I) entwickelt, welches mittels 2PP strukturiert werden konnte, was anhand kleiner wie auch großer Scaffolds mit dem Material demonstriert wurde. Dazu wurde das kommerziell erhältliche Alkoxysilan-Molekül O-(Methacryloxyethyl)-N-(triethoxysilylpropyl)urethan als Precursor verwendet. Durch eine bewusst unvollständige Hydrolyse- und Kondensationsreaktion konnte aus dem Precursorsilan ein Hybridpolymerharz hergestellt werden, welches anorganisch vorverknüpft war. Weiterhin wies es sowohl als Volumenpolymer, als auch in Form von Scaffold-Strukturen eine sehr gute Biokompatibilität auf. Um zu untersuchen, ob die im Hybridpolymer enthaltenen prinzipiell degradierbaren Gruppen unter physiologischen Bedingungen tatsächlich degradieren und Teile aus dem Polymerverband herausgelöst werden können, wurde ein selbstentwickeltes Verfahren für stationäre Degradations-untersuchungen in phosphat-gepufferter Saline (PBS, pH = 7,4) verwendet. Die durch die photochemische Polymerisation neu entstandenen Ketten besaßen ihrer Natur gemäß keine hydrolysierbaren Einheiten, weshalb das Hybridpolymer nicht vollständig degradieren kann. Es konnte jedoch ein prinzipieller Zugang zu Gerüstträgerstrukturen auf Basis photovernetzbarer Polymere für die Regenerative Medizin geschaffen werden. N2 - The objective was the investigation of photo-curable and patternable (hybrid) polymers for applications in regenerative medicine, in order to explore basic principles for scaffold fabrication by two-photon polymerization. This would enable patient-individual medical implants. As model systems for subsequent investigations, the monomers Acr-1, MAcr-2, Acr-3, MAcr-4, and DiMAcr-5 were synthesized. These compounds are well comparable organic (meth)acrylate monomers with a functionality of one and two, respectively. The monomers Acr-3, MAcr-4, and DiMAcr-5 were combined with a well-known methacrylate-based inorganic-organic hybrid polymer ORMOCER® I in different molar ratios. After preparation of the monomers and their formulations with ORMOCER® I introducing defined amounts of photoinitiator Irgacure® 369 into the material systems, the materials’ reaction was monitored in situ by photo-DSC investigations. In particular, the effect of the different monomer ratios on the copolymerization behavior was studied in more detail. A higher maximum polymerization rate and, therewith, a higher reaction speed was found for all formulations of monomer mixtures in contrast to the corresponding individual monomers (synergy effect). Moreover, by comparing the various organic monomers, considerable differences could be identified in between acrylates and methacrylates as well as for the mono- and difunctional species. These effects were explained by means of the type of their photochemically organically cross-linkable functional groups and thus their resulting reactivity as well as by the monomer structure and functionality itself, resulting in different diffusion abilities of mono-, oligo- and polymeric species within gelled systems. Furthermore, the influence of several photoinitiators and the initiator concentration on the photochemically induced copolymerization was investigated. Besides the initiator concentration, also the initiators’ absorption properties, the resin matrix and the initiators’ efficiency play an important role for the reaction profile of the photochemical cross-linking. All different photoinitiators were introduced into the model system in three different concentrations to explore the induced alterations on the reaction profile. For some of the investigated initiators, the maximum polymerization rate RP,max and, therewith, the overall reaction kinetics increased with increasing photoinitiator concentration, but for other initiators, the maximum polymerization rate RP,max was lowered at increased initiator concentrations. Thus, a general relationship between the photoinitiator concentration and the maximum polymerization rate RP,max could not be identified. First structures were generated out of selected mixtures by two-photon polymerization in order to demonstrate the novel materials’ ability of being patterned in three dimensions. Three dimensional structures were generated with specific parameter combinations of laser power and writing speed, whereas each parameter set corresponds to an individual exposure dose deposited in the materials’ volume. In particular, different structure widths were observed for different material formulations fabricated with the same parameter sets. Thus, it was possible for the first time to experimentally observe different chemical interaction volumes. These interaction volumes were correlated to the different reaction profiles of the material formulations, which were received via 1PP photo-DSC measurements. It was shown that the structure volume depends on the functionality of the employed monomers, because their degree of cross-linking depends on their functionality. The degree of cross-linking which results upon polymerization determines, whether a structure maintains stable during the subsequent development process. In the second part of this work, a biocompatible and photo-patternable hybrid material was developed. Commercially available O-(methacryloxyethyl)-N-(triethoxysilylpropyl)-urethane was chosen for an intentional incomplete hydrolysis and condensation reaction in order to receive a RENACER® resin, which includes functional groups for subsequent organic cross-linking. This material showed a very good patterning performance, which was demonstrated by a series of structures and scaffolds. The material yields a good biocompatibility. In order to investigate, whether the hydrolysable functional groups within the hybrid polymer actually degrade under physiological conditions, a procedure routine for stationary degradation studies in phosphate-buffered saline (PBS) was developed. The carbon chain generated through photochemical cross-linking, has no hydrolyzable groups and naturally cannot be degraded, resulting in a hybrid polymer which is not completely degradable. However, a principal access to scaffolds for regenerative medicine on the basis of photo-curable polymers was accomplished which was the purpose of this work. KW - Photopolymerisation KW - Zwei-Photonen-Polymerisation KW - Copolymerisation KW - Reaktionskinetik KW - Biokompatibilität KW - Photo-DSC KW - Kinetik Y1 - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-97131 ER - TY - THES A1 - Schug, Benedikt T1 - Untersuchungen zur Ursache und Beeinflussung des Kriechverhaltens von Gips T1 - Investigations into the origin and the influencing of the creep behavior of gypsum N2 - In dieser Arbeit konnte ein weiterer und möglicherweise entscheidender Schritt zur Aufklärung des Kriechmechanismus von Gips gemacht und darauf aufbauend Kriterien, Wege und Strategien aufgezeigt werden, um neue Antikriechmittelsubstanzen zu identifizieren oder vorhandene Kriechmittel gezielt zu verbessern. Die Gültigkeit und Praxistauglichkeit der Kriterien wurde exemplarisch nachgewiesen. Die Basis der Untersuchungen wurde gelegt mit der Errichtung standardisierter Messaufbauten und Verfahren sowie Parameterauswahl für eine beschleunigte und reproduzierbare Darstellung des Kriechphänomens, wobei zunächst im Abgleich sichergestellt wurde, dass das beschleunigte Phänomen mit dem langsam über einen Zeitraum von Jahren erzeugten Phänomen deckungsgleich ist. Darauf aufbauend wurden innovative Untersuchungsmethoden entwickelt, um das Kriechverhalten zu charakterisieren und qualitativ sowie quantitativ zu analysieren. Hierzu wurde zunächst ein Aufbau und eine Messroutine entwickelt und eingeführt, um morphologische Veränderungen während des Kriechvorgangs im Rasterelektronenmikroskop nachzuverfolgen. Im Weiteren wurden Versuchsaufbauten für statische 3-Punkt-Biegeversuche in verschiedenen Lösungen realisiert und diese ergebnisabhängig optimiert. Hierdurch konnte der Einfluss der Löslichkeit von Gips in den entsprechenden Medien auf das Kriechverhalten untersuchen werden. Mittels Laserscanning-Mikroskop wurden wiederum diese Ergebnisse untermauert. Als vorherrschender Kriechmechanismus von Gips wurde damit das Abgleiten einzelner Gipskristalle bedingt durch einen Lösungs-Abscheide-Mechanismus an Orten hoher mechanischer Belastung identifiziert und bestätigt. N2 - In this work, a further and possibly decisive step could be taken towards clarifying the creep mechanism of gypsum and, based on this, ways and strategies could be identified in order to identify new anti-creep agents or to specifically improve existing anti-creep agents. The validity and practicability of the selection criteria for new anti-creep agents was demonstrated by several examples of selections of chemical moieties, to date unknown with respect to their activity as anti-creep agent for gypsum. The fundament of the investigations was laid with the establishment of standardised measurement setups and procedures as well as with the selection of parameters for an accelerated and reproducible representation of the creep phenomenon, whereby it was ensured that the accelerated creep is comparable to natural, slow creep which usually takes up to several years in gypsum materials. On this basis, innovative investigation methods were developed to characterise the creep behaviour and to analyse it qualitatively and quantitatively. Firstly, a setup and a measuring routine were developed and introduced to track morphological changes during the creep process via scanning electron microscopy. Secondly, test setups for static 3-point bending tests were realized in different solutions and optimized. This enabled the investigation of the correlation between the solubility of gypsum in different media and the resulting creep behaviour. These results were substantiated further by means of laser scanning microscopy. Using these methods, it was possible to identify and confirm the slippage of individual gypsum crystals due to a solution deposition mechanism at locations of high mechanical stress as the predominant creep mechanism of gypsum. The creep of gypsum is thus decisively determined by an increased humidity in the pores of gypsum, which results in an enlargement of the water layer in the space between the gypsum crystals in the polycrystalline structure. Thus, gypsum crystals can slide more easily against each other under load via the mechanism of the so-called "pressure solution creep". This mechanism could be confirmed by creep tests with different large gypsum crystals in the polycrystalline gypsum body. Thus, the creep velocity results primarily from the number and size of the contact points of the gypsum crystal as well as the solubility of the crystals at these interfaces in the pore liquid. Particulate, hydraulic and surface-active additives were tested to influence the creep behaviour of gypsum. In particular, the industrial anti-creep agent sodium trimetaphosphate (STMP) was investigated in detail. The mode of action of STMP as a state-of-the-art creeping agent was demonstrated by EDX mappings and transmission electron micrsocopy. The decisive influencing variables for anti-creep agents were identified to be the following ones: • A good solubility in water, which makes it possible to employ the anti-creep agent of choice in the mixing water used to form the gypsum material. • A moderate complex formation with calcium ions in the size range around log (KB) = 2.5. This moderate complex stability does significantly not hinder the crystal formation of the gypsum crystals on the one hand, but on the other hand enables a complex formation on the gypsum crystal surfaces. The surface coating which is thereby obtained, reduces the dissolution rate of gypsum in water. This is achieved by a surface coating on only certain crystal surfaces. In this thesis, the (100) and (001) planes were identified to be most preferentially complexed / coated with anti-creep agent. • A reinforcement of the gypsum matrix by "sticking" the crystals, as observed in-situ via transmission electron microscopy, also plays a role. This reinforcement may ultimately also be a reason for the increased dimensional stability. Based on these mechanisms which were identified for the state-of-the-art anti-creep agent STMP, novel chemical moieties as potential anti-creep agent candidates were selected. Surface-active additives such as poly(acrylic acid-co-maleic acid) (PAMA) were identified as a promising alternative to STMP. They are water-soluble, contain complexing centres for calcium ions with the same complexing constant as STMP and are toxicologically harmless. Ultimately, in the laboratory, these polymers, based on experiments with pure FGD gypsum, could well compete with the performance of STMP with regard to hinder creep of gypsum. KW - Rauchgasgips KW - Kriechen KW - Bassanit KW - Kriechverhalten Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:20-opus-246503 ER -