Refine
Has Fulltext
- yes (16)
Is part of the Bibliography
- yes (16)
Year of publication
- 2023 (16) (remove)
Document Type
- Doctoral Thesis (16) (remove)
Keywords
- Topologischer Isolator (6)
- ARPES (3)
- Computertomographie (2)
- Fotovoltaik (2)
- Nanometerbereich (2)
- Perovskite (2)
- Perowskit (2)
- Rasterelektronenmikroskopie (2)
- Rastertunnelmikroskop (2)
- Rastertunnelmikroskopie (2)
Institute
- Physikalisches Institut (16) (remove)
Diese Arbeit befasst sich mit der Weiterentwicklung und Charakterisierung des XRM-II nanoCT Systems, sowie dessen Möglichkeiten zur Materialtrennung und Elementbestimmung in der nano-Computertomographie. Beim XRM-II nanoCT System handelt es sich um ein Röntgenmikroskop, welches in ein Rasterelektronenmikroskop integriert ist, und auf dem Prinzip der geometrischen Vergrößerung basiert. Neben zweidimensionalen Durchstrahlungsbildern ist dieses Mikroskop auch zur dreidimensionalen Bildgebung mittels Computertomographie fähig.
Der Ausgangspunkt für die Weiterentwicklung ist das XRM-II, mit welchem bereits Computertomographien im Nanometerbereich möglich waren. Deren Aufnahmedauer liegt zwischen 14 und 21 Tagen, was das System trotz seiner hohen Auflösung wenig praktikabel macht. Durch eine Anpassung der Blendeneinstellungen am Rasterelektronenmikroskop konnte der Strahlstrom um den Faktor 40 erhöht und damit die Aufnahmedauer auf 24 Stunden reduziert werden, wobei weiterhin eine zweidimensionale Auflösung von \(167 \pm 9\) nm erreicht wird. Durch die Trennung von Objekt- und Targetmanipulator lassen sich beide unabhängig und genauer bewegen, wodurch es möglich ist selbst 50 nm große Strukturen abzubilden.
Die Charakterisierung erfolgt sowohl für das komplette System als auch getrennt in die entscheidenden Komponenten wie Target und Detektor. Für das Röntgentarget werden Monte-Carlo Simulationen zur Brennfleckgröße, welche entscheidend für die erreichbare Auflösung ist, durchgeführt und mit Auflösungstests verglichen. Der Röntgendetektor wird hinsichtlich seiner spektralen Auflösung überprüft, welche hauptsächlich vom Charge Sharing Effekt beeinflusst wird. Die Charakterisierung des Gesamtsystems erfolgt durch den Vergleich mit einer höher auflösenden Bildgebungsmethode, der FIB Tomographie. Hierbei wird die gleiche Probe, ein Bruchstück einer CPU, mit beiden Methoden unter der Voraussetzung einer ähnlichen Aufnahmezeit (24 h) untersucht. In der nano-CT kann ein 12 mal größeres Volumen analysiert werden, was jedoch eine geringere räumliche Auflösung als die FIB Tomographie mit sich bringt.
Da die spektrale Auflösung des Detektors aufgrund des Charge Sharing begrenzt ist, lassen sich nur Materialien mit einem großen Unterschied in der Ordnungszahl mittels der Energieschwellen des Detektors trennen. Jedoch kann in Verbindung mit der geeigneten Wahl des Targetmaterials der Absorptionskontrast für leichte Materialien, wie beispielsweise \(SiO_2\) verbessert werden. Darüber hinaus ist es am XRM-II nanoCT möglich, durch das integrierte EDX-System, Elemente in der Computertomographie zu identifizieren. Dies wird anhand eines Drei-Wegekatalysators und eines NCA-Partikel gezeigt.
Two-dimensional (2D) topological insulators are a new class of materials with properties that are
promising for potential future applications in quantum computers. For example, stanene represents
a possible candidate for a topological insulator made of Sn atoms arranged in a hexagonal
lattice. However, it has a relatively fragile low-energy spectrum and sensitive topology. Therefore,
to experimentally realize stanene in the topologically non-trivial phase, a suitable substrate
that accommodates stanene without compromising these topological properties must be found.
A heterostructure consisting of a SiC substrate with a buffer layer of adsorbed group-III elements
constitutes a possible solution for this problem. In this work, 2D adatom systems of Al and In
were grown epitaxially on SiC(0001) and then investigated structurally and spectroscopically by
scanning tunneling microscopy (STM) and photoelectron spectroscopy.
Al films in the high coverage regime \( (\Theta_{ML}\approx2\) ML\( ) \) exhibit unusually large, triangular- and
rectangular-shaped surface unit cells. Here, the low-energy electron diffraction (LEED)
pattern is brought into accordance with the surface topography derived from STM. Another Al
reconstruction, the quasi-one-dimensional (1D) Al phase, exhibits a striped surface corrugation,
which could be the result of the strain imprinted by the overlayer-substrate lattice mismatch.
It is suggested that Al atoms in different surface areas can occupy hexagonal close-packed and
face-centered cubic lattice sites, respectively, which in turn lead to close-packed transition regions
forming the stripe-like corrugations. On the basis of the well-known herringbone reconstruction
from Au(111), a first structural model is proposed, which fits well to the structural data from
STM. Ultimately, however, thermal treatments of the sample could not generate lower coverage
phases, i.e. in particular, a buffer layer structure.
Strong metallic signatures are found for In high coverage films \( (\Theta_{ML}\approx3\) to \(2\) ML\() \) by
scanning tunneling spectroscopy (STS) and angle-resolved photoelectron spectroscopy (ARPES),
which form a \( (7\times7) \), \( (6\times4\sqrt{3}) \), and \( (4\sqrt{3}\times4\sqrt{3}) \) surface reconstruction. In all these In phases
electrons follow the nearly-free electron model. Similar to the Al films, thermal treatments could
not obtain the buffer layer system.
Surprisingly, in the course of this investigation a triangular In lattice featuring a \( (1\times1) \)
periodicity is observed to host massive Dirac-like bands at \( K/K^{\prime} \) in ARPES. Based on this
strong electronic similarity with graphene at the Brillouin zone boundary, this new structure is
referred to as \textit{indenene}. An extensive theoretical analysis uncovers the emergence of an electronic
honeycomb network based on triangularly arranged In \textit{p} orbitals. Due to strong atomic spin-orbit
coupling and a comparably small substrate-induced in-plane inversion symmetry breaking this
material system is rendered topologically non-trivial. In indenene, the topology is intimately
linked to a bulk observable, i.e., the energy-dependent charge accumulation sequence within the
surface unit cell, which is experimentally exploited in STS to confirm the non-trivial topological
character. The band gap at \( K/K^{\prime} \), a signature of massive Dirac fermions, is estimated by
ARPES to approximately 125 meV. Further investigations by X-ray standing wave, STM, and
LEED confirm the structural properties of indenene. Thus, this thesis presents the growth and
characterization of the novel quantum spin Hall insulator material indenene.
A plethora of novel material concepts are currently being investigated in the condensed matter research community. Some of them hold promise to shape our everyday world in a way that silicon-based semiconductor materials and the related development of semiconductor devices have done in the past. In this regard, the last decades have witnessed an explosion of studies concerned with so called ‘’quantum materials’’ with emerging novel functionalities. These could eventually lead to new generations of electronic and/or spintronic devices. One particular material class, the so called topological materials, play a central role. As far as their technological applicability is concerned, however, they are still facing outstanding challenges to date.
Predicted for the first time in 2005 and experimentally verified in 2007, two-dimensional topological insulators (2D TIs) (a.k.a. quantum spin Hall insulators) exhibit the outstanding property of hosting spin-polarized metallic states along the boundaries of the insulating 2D bulk material, which are protected from elastic single-particle backscattering and give rise to the quantum spin Hall effect (QSHE). Owing to these peculiar properties the QSHE holds promise for dissipationless charge and/or spin transport. However, also in today’s best 2D TIs the observation of the QSHE is still limited to cryogenic temperatures of maximum 100 K. Here, the discovery of bismuthene on SiC(0001) has marked a milestone towards a possible realization of the QSHE at or beyond room-temperature owing to the massively increased electronic bulk energy gap on the order of 1 eV. This thesis is devoted to and motivated by the goal of advancing its synthesis and to build a deeper understanding of its one-particle and two-particle electronic properties that goes beyond prior work.
Regarding the aspect of material synthesis, an improved growth procedure for bismuthene is elaborated that increases the domain size of the material considerably (by a factor of ≈ 3.2 - 6.5 compared to prior work). The improved film quality is an important step towards any future device application of bismuthene, but also facilitates all further basic studies of this material.
Moreover, the deposition of magnetic transition metals (Mn and Co) on bismuthene is investigated. Thereby, the formation of ordered magnetic Bi-Mn/Co alloys is realized, their structure is resolved with scanning tunneling microscopy (STM), and their pristine electronic properties are resolved with scanning tunneling spectroscopy (STS) and photoemission spectroscopy (PES). It is proposed that these ordered magnetic Bi-Mn/Co-alloys offer the potential to study the interplay between magnetism and topology in bismuthene in the future.
In this thesis, a wide variety of spectroscopic techniques are employed that aim to build an understanding of the single-particle, as well as two-particle level of description of bismuthene's electronic structure. The techniques involve STS and angle-resolved PES (ARPES) on the one hand, but also optical spectroscopy and time-resolved ARPES (trARPES), on the other hand. Moreover, these experiments are accompanied by advanced numerical modelling in form of GW and Bethe-Salpeter equation calculations provided by our theoretical colleagues. Notably, by merging many experimental and theoretical techniques, this work sets a benchmark for electronic structure investigations of 2D materials in general.
Based on the STS studies, electronic quasi-particle interferences in quasi-1D line defects in bismuthene that are reminiscent of Fabry-Pérot states are discovered. It is shown that they point to a hybridization of two pairs of helical boundary modes across the line defect, which is accompanied by a (partial) lifting of their topological protection against elastic single-particle backscattering.
Optical spectroscopy is used to reveal bismuthene's two-particle elecronic structure. Despite its monolayer thickness, a strong optical (two-particle) response due to enhanced electron-hole Coulomb interactions is observed. The presented combined experimental and theoretical approach (including GW and Bethe-Salpeter equation calculations) allows to conclude that two prominent optical transitions can be associated with excitonic transitions derived from the Rashba-split valence bands of bismuthene. On a broader scope this discovery might promote further experiments to elucidate links of excitonic and topological physics.
Finally, the excited conduction band states of bismuthene are mapped in energy and momentum space employing trARPES on bismuthene for the first time. The direct and indirect band gaps are succesfully extracted and the effect of excited charge carrier induced gap-renormalization is observed. In addition, an exceptionally fast excited charge carrier relaxation is identified which is explained by the presence of a quasi-metallic density of states from coupled topological boundary states of domain boundaries.
The presented thesis deals with the investigation of the characteristic physical properties of lead-free double perovskites. For this purpose lead-free double perovskite single crystals were grown from solution. In order to assess the influence of growth temperature on tail states in the material, the crystals were studied using Photoluminescence Excitation (PLE) and Transmission measurements. Additionally, lead-free double perovskite solar cells and thin films were investigated to address the correlation of precursor stoichiometry and solar cell efficiency. In a last step a new earth abundant lead-free double perovskite was introduced and its physical properties were studied by photoluminescene and absorptance. Like this it was possible to assess the suitability of this material for solar cell applications in the future.
In der vorliegenden Arbeit werden die Konzeption und Realisierung eines Computertomographen zur Materialanalyse auf Basis eines Rasterelektronenmikroskops mit einem räumlichen Auflösungsvermögen im Nanometerbereich diskutiert. Durch einen fokussierten Elektronenstrahl, der mit einer Beschleunigungsspannung von 30 kV auf eine mikrostrukturierte Wolframnadel mit einem Spitzenradius von bis zu 50 nm gezielt wird, entsteht ein kleiner Röntgenbrennfleck über den mit geometrischer Vergrößerung hochauflösende Projektionen eines zu untersuchenden Objekts erzeugt werden. Durch Rotation des Testobjekts werden Projektionen aus verschiedenen Blickwinkeln aufgenommen und über einen speziellen Rekonstruktionsalgorithmus zu einem 3-dimensionalen Bild zusammengefügt.
Bei der Beurteilung der Einzelkomponenten des Geräts wird insbesondere auf Struktur, Form und den elektrochemischen Herstellungsprozess der Röntgenquelle eingegangen. Eine ausreichend genaue Positionierung von Messobjekt und Röntgenbrennfleck wird über Piezoachsen realisiert, während die Stabilität des Röntgenbrennflecks über die Elektronenoptik des Rasterelektronenmikroskops und die Form der Quellnadel optimiert wird.
Das räumliche Auflösungsvermögen wird über die Linienspreizfunktion an Materialkanten abgeschätzt. Für eine Wolfram-Block-Quelle ergibt sich dabei ein Auflösungsvermögen von 325 nm – 400 nm in 3D, während der Quellfleck einer Wolframnadel das Auflösungsvermögen der Anlage auf 65 nm – 90 nm in 2D und 170 nm – 300 nm in 3D bei Messungen an einem AlCu29-Testobjekt anhebt. Außerdem werden die Auswirkungen der Phasenkontrastcharakteristik der Röntgenquelle auf die rekonstruierten Bilder nach Anwendung eines Paganin-Filters diskutiert. Dabei zeigt sich, dass durch Anwendung des Filters ein verbessertes Signal-zu-Rausch-Verhältnis auf Kosten der räumlichen Bildauflösung erzielt werden kann.
Eine Vergleichsmessung mit einem kommerziell verfügbaren Röntgenmikroskop zeigt die Stärken des vorgestellten Systems bei Untersuchung von stark absorbierenden Messobjekten. Das kompakte Design erlaubt eine Weiterentwicklung in Richtung eines nanoCT-Moduls als Upgrade Option für Rasterelektronenmikroskope im Gegensatz zu den weitaus teureren bisher verbreiteten nanoCT-Geräten.
Magnetic systems underlie the physics of quantum mechanics when reaching the limit of few or even single atoms. This behavior limits the minimum size of magnetic bits in data storage devices as spontaneous switching of the magnetization leads to the loss of information. On the other hand, exactly these quantum mechanic properties allow to use such systems in quantum computers. Proposals to realize qubits involve the spin states of single atoms as well as topologically protected Majorana zero modes, that emerge in coupled systems of magnetic atoms in proximity to a superconductor. In order to implement and control the proposed applications, a detailed understanding of atomic spins and their interaction with the environment is required.
In this thesis, two different systems of magnetic adatoms coupled to metallic and superconducting surfaces are studied by means of scanning tunneling microscopy (STM) and spectroscopy: Co atoms on the clean Cu(111) were among the first systems exhibiting signatures of the Kondo effect in an individual atom. Yet, a recent theoretical work proposed an alternative interpretation of these early experimental results, involving a newly described many-body state. Spin-averaged and -polarized experiments in high magnetic fields presented in this thesis confirm effects beyond the Kondo effect that determine the physics in these Co atoms and suggest a potentially even richer phenomenology than proposed by theory.
The second studied system are single and coupled Fe atoms on the superconducting Nb(110) surface. Magnetic impurities on superconducting surfaces locally induce Yu-Shiba-Rusinov (YSR) states inside the superconducting gap due to their pair breaking potential. Coupled systems of such impurities exhibit YSR bands and, if the bands cross the Fermi level such that the band structure is inverted, host Majorana zero modes. Using the example of Fe atoms on Nb(110), the YSR states’ dependence on the adatom–substrate interaction as well as the interatomic YSR state coupling is investigated. In the presence of oxygen on the Nb surface, the adatom–substrate interaction is shown to be heavily modified and the YSR states are found to undergo a quantum phase transition, which can be directly linked to a modified Kondo screening.
STM tips functionalized with CO molecules allow to resolve self-assembled one-dimensional chains of Fe atoms on the clean Nb(110) surface to study the YSR states’ coupling. Mapping out the states’ wave functions reveals their symmetry, which is shown to alter as a function of the states’ energy and number of atoms in the chain. These experimental results are reproduced in a simple tight-binding model, demonstrating a straightforward possibility to describe also more complex YSR systems toward engineered, potentially topologically non-trivial states.
This work presents a newly developed method for the epitaxial growth of the half-Heusler antiferromagnet CuMnSb. All necessary process steps, from buffer growth to the deposition of a protective layer, are presented in detail. Using structural, electrical, and magnetic characterization, the material parameters of the epitaxial CuMnSb layers are investigated.
The successful growth of CuMnSb by molecular beam epitaxy is demonstrated on InAs (001), GaSb (001), and InP (001) substrates. While CuMnSb can be grown pseudomorphically on InAs and GaSb, the significant lattice mismatch for growth on InP leads to relaxation already at low film thicknesses. Due to the lower conductivity of GaSb compared to InAs, GaSb substrates are particularly suitable for the fabrication of CuMnSb layers for lateral electrical transport experiments. However, by growing a high-resistive ZnTe interlayer below the CuMnSb layer, lateral transport experiments on CuMnSb layers grown on InAs can also be realized. Protective layers of Ru and Al2O3 have proven to be suitable for protecting the CuMnSb layers from the environment.
Structural characterization by high resolution X-ray diffraction (full width at half maximum of 7.7 ′′ of the rocking curve) and atomic force microscopy (root mean square surface roughness of 0.14 nm) reveals an outstanding crystal quality of the epitaxial CuMnSb layers. The half-Heusler crystal structure is confirmed by scanning transmission electron microscopy and the stoichiometric material composition by Rutherford backscattering spectrometry. In line with the high crystal quality, a new minimum value of the residual resistance of CuMnSb (𝜌0 = 35 μΩ ⋅ cm) could be measured utilizing basic electrical transport experiments.
An elaborate study of epitaxial CuMnSb grown on GaSb reveals a dependence of the vertical lattice parameter on the Mn/Sb flux ratio. This characteristic enables the growth of tensile, unstrained, and compressive strained CuMnSb layers on a single substrate material. Additionally, it is shown that the Néel temperature has a maximum of 62 K at stoichiometric material composition and thus can be utilized as a selection tool for stoichiometric CuMnSb samples. Mn-related defects are believed to be the driving force for these observations.
The magnetic characterization of the epitaxial CuMnSb films is performed by superconducting quantum interference device magnetometry. Magnetic behavior comparable to the bulk material is found, however, an additional complex magnetic phase appears in thin CuMnSb films and/or at low magnetic fields, which has not been previously reported for CuMnSb. This magnetic phase is believed to be localized at the CuMnSb surface and exhibits both superparamagnetic and spin-glass-like behavior. The exchange bias effect of CuMnSb is investigated in combination with different in- and out-of-plane ferromagnets. It is shown that the exchange bias effect can only be observed in combination with in-plane ferromagnets.
Finally, the first attempts at the growth of fully epitaxial CuMnSb/NiMnSb heterostructures are presented. Both magnetic and structural studies by secondary-ion mass spectrometry indicate the interdiffusion of Cu and Ni atoms between the two half-Heusler layers, however, an exchange bias effect can be observed for the CuMnSb/NiMnSb heterostructures. Whether this exchange bias effect originates from exchange interaction between the CuMnSb and NiMnSb layers, or from ferromagnetic inclusions in the antiferromagnetic layer can not be conclusively identified.
Das Ziel der vorliegenden Arbeit war die Entwicklung neuer, robuster Methoden der Spin-Lock-basierten MRT. Im Fokus stand hierbei vorerst die T1ρ-Quantifizierung des Myokards im Kleintiermodell. Neben der T1ρ-Bildgebung bietet Spin-Locking jedoch zusätzlich die Möglichkeit der Detektion ultra-schwacher, magnetischer Feldoszillationen. Die Projekte und Ergebnisse, die im Rahmen dieses Promotionsvorhabens umgesetzt und erzielt wurden, decken daher ein breites Spektrum der Spin-lock basierten Bildgebung ab und können grob in drei Bereiche unterteilt werden. Im ersten Schritt wurde die grundlegende Pulssequenz des Spin-Lock-Experimentes durch die Einführung des balancierten Spin-Locks optimiert. Der zweite Schritt war die Entwicklung einer kardialen MRT-Sequenz für die robuste Quantifizierung der myokardialen T1ρ-Relaxationszeit an einem präklinischen Hochfeld-MRT. Im letzten Schritt wurden Konzepte der robusten T1ρ-Bildgebung auf die Methodik der Felddetektion mittels Spin-Locking übertragen. Hierbei wurden erste, erfolgreiche Messungen magnetischer Oszillationen im nT-Bereich, welche lokal im untersuchten Gewebe auftreten, an einem klinischen MRT-System im menschlichen Gehirn realisiert.
Rotationsdriftspektroskopie
(2023)
Die wachsende Verfügbarkeit von magnetischen Nanopartikeln (MNPs) mit funktionalisierten
Partikeloberflächen eröffnet weitreichende Möglichkeiten für chemische, biologische und klinische
Analysemethoden. Durch Funktionalisierung kann eine gezielte Interaktion mit Molekülen bewirkt
werden, die im Allgemeinen auch die Beweglichkeit der MNPs verändern. Methoden zur
Charakterisierung von MNPs wie bspw. AC-Suszeptometrie, Magnetorelaxometrie (MRX) oder
Magnetic Particle Spectroscopy (MPS) können diese Änderung der Beweglichkeit bei MNPs
messen, wenn es sich um MNPs handelt, deren magnetisches Moment im Partikel fixiert ist. Damit
ist mit funktionalisierten MNPs indirekt auch die spezifische Messung von Molekülkonzentrationen
möglich. MNPs können zudem in biokompatibler Form hergestellt werden und sind dadurch auch
als in-vivo Marker einsetzbar. Das 2005 das erste Mal veröffentlichte Magnetic Particle Imaging
(MPI) kann als ein mittels Gradientenfeldern um die räumliche Kodierung erweitertes MPS
betrachtet werden. Dank biokompatibler MNPs handelt es sich dabei um eine in-vivo-taugliche,
nicht-invasive Bildgebungsmethode. Mit funktionalisierten MNPs als Marker ist damit im Prinzip
auch molekulare Bildgebung möglich, die durch Detektion der beteiligten Moleküle (Biomarker)
Stoffwechselprozesse räumlich abbilden kann. Im Vergleich zur Bildgebung von Gewebe- und
Knochenstrukturen lassen sich die diagnostischen Möglichkeiten durch molekulare Bildgebung
erheblich erweitern.
Rotationsdriftspektroskopie (Rotational Drift Spectroscopy, RDS) ist eine in dieser Arbeit
entwickelte Methode für die induktive Messung der Beweglichkeit von MNPs in flüssiger
Suspension. Es verwendet die Rotationsdrift von MNPs in rotierenden magnetischen Feldern als
Grundlage und bietet das Potential die Änderungen der Beweglichkeit von MNPs mit einer
Empfindlichkeit messen zu können, welche potentiell um mehrere Größenordnungen höher sein
kann als mit den oben erwähnten Verfahren. Die vorliegende Arbeit konzentriert sich auf die
Verwendbarkeit dieses Effekts als Spektroskopiemethode. Die Eigenschaften des RDS-Signals sind
jedoch auch als Grundlage für räumliche Kodierung vielversprechend. In weiterführenden Projekten
soll daher auch die Entwicklung von Rotationsdriftbildgebung (Rotating Drift Imaging, RDI) als ein
nicht-invasives Verfahren für molekulare Bildgebung angestrebt werden.
Der Grundgedanke von RDS entlehnt sich aus einem in 2006 veröffentlichten Sensordesign
basierend auf magnetische Mikropartikel in einem schwachen rotierenden Magnetfeld. Das
rotierende Magnetfeld ist dabei so schwach gewählt, dass sich das Partikel aufgrund der viskosen
Reibung nicht mehr synchron mit dem externen Feld drehen kann. Die Frequenz der resultierenden
asynchronen Rotationsdrift liegt unterhalb der Frequenz des externen Rotationsfelds und ist
Abhängig von der viskosen Reibung. Aufgrund dieser Abhängigkeit können Änderungen im
Reibungskoeffizienten des Partikels über Änderungen in der Rotationsdriftfrequenz gemessen
werden.
RDS zielt darauf ab, diese Rotationsdrift bei suspendierten MNPs über deren
makroskopische Magnetisierung messen zu können. Damit wird u.a. auch die nicht-invasive
Messung von MNPs innerhalb opaker biologischer Proben möglich. MNP-Suspensionen sind
großzahlige Nanopartikel-ensembles und können nicht wie ein einzelnes Mikropartikel gemessen
werden. Für die induktive Messung ist vor dem Start eine Ausrichtung aller magnetischen Momente
nötig, da sich deren makroskopische Magnetisierung andernfalls zu Null addiert. Aufgrund von
Rotationsdiffusion bleibt diese Ausrichtung nur eine begrenzte Zeit bestehen, so dass auch die
eigentliche Messung des RDS-Signals nur eine begrenzte Zeit möglich ist. Diese Ausrichtung wurde
in den ersten Experimenten durch einen kurzen Magnetfeldpuls erzeugt. In der Empfangsspule ist
die Induktion durch das Rotationsfeld typischer Weise um mehrere Größenordnungen höher als das
zu erwartende Signal und muss durch einen Tiefpass unterdrückt werden. In diesem Tiefpassfilter
ruft jedoch die Einkopplung des Anfangspulses eine Pulsantwort hervor, die ebenso mehrere
Größenordnungen des zu erwartenden Signals betragen kann und ähnlich langsam wie typische
Signale abklingt. Die Unterdrückung dieser Pulsantwort stellte in den ersten Experimenten die
größte Hürde da. Der erste Aufbau hatte eine Relaisschaltung zur Pulsunterdrückung und resultierte
in einer Totzeit von 3 ms zwischen Anfangspuls und Start der Messung. Aufgrund dieser Totzeit
waren die ersten Messungen auf größere Agglomerate und Sedimente von MNPs beschränkt, da nur
in diesem Fall eine hinreichend lange Zerfallsdauer der Probenmagnetisierung vorlag. Das
Verhalten derartiger Partikelsysteme ist jedoch aufgrund von mechanischer und magnetischer
Interpartikelwechselwirkung vergleichsweise komplex und theoretisch schwer modellierbar. Das
primäre Zielsystem für RDS hingegen, Eindomänenpartikel mit im Partikel fixierter Magnetisierung
und Punktsymmetrie bzgl. des Reibungstensors, erlaubt die Aufstellung einer parametrisierten
Funktion für den Signalverlauf. Es ermöglicht somit aufgrund der besseren Berechenbarkeit eine
solidere Auswertung des RDS-Signals. Um Eindomänenpartikel in wässriger Suspension mit
typischen Partikeldurchmessern um 100 nm messen zu können ist eine Verkürzung der Totzeit auf
mindestens 1/10 erforderlich.
Prinzipiell kann diese Problematik durch die Verwendung schneller Halbleiterschalter in
Verbindung mit einer präzise abstimmbaren induktiven Entkopplung des Spulensystems gemindert
werden. Simulationen des RDS-Signals für verschiedene RDS-Sequenzen zeigen jedoch noch zwei
weitere Möglichkeiten auf, die ohne aufwändigen Eingriffe in der Hardware auskommen. Zum
einen kann durch orthogonales Frequenzmischen mit geeignetem Frequenz- und Phasenverhältnis
eine Ausrichtung der magnetischen Momente bewirkt werden. Da die benötigten Frequenzen
vollständig im Sperrband des Tiefpassfilters liegen können, lässt sich damit die Pulsantwort bei
hinreichend „weichem“ Umschalten zwischen der Polarisierungssequenz und der RDS-Sequenz
vollständig vermeiden. Darüber hinaus zeigt sich, dass es bei Anwesenheit eines schwachen
Offsetfelds (< 10 % der Rotationsfeldamplitude) zu einer Ausrichtung der magnetischen Momente
kommt, wenn das magnetische Rotationsfeld seine Richtung ändert und diese Änderung nicht
abrupt erfolgt, sondern das Rotationsfeld übergangsweise in ein linear oszillierendes Feld übergeht.
Hingegen wird die Wirkung des Offsetfelds durch das Rotationsfeld vor und nach dem Wechsel
nahezu vollständig neutralisiert, so dass damit das Störsignale generierende Schalten eines
Offsetfelds ersetzt werden kann. Es ist auf diese Weise nicht möglich, Echosequenzen zu erzeugen,
da hier bei der für Echosequenzen benötigten Richtungsumkehr des Rotationsfelds die zuvor
aufgeprägte Phasenverteilung durch das Offsetfeld zerstört wird und somit anstelle einer
Signalechogenerierung eine neue RDS-Messung gestartet wird. Obwohl es Echosequenzen mit
Anfangspuls erlauben, mehr MNP Parameter zu messen, bietet dieser Ansatz dennoch
entscheidende Vorteile. So ergibt sich eine massive Vereinfachung der Hardware und es sind bei
gleicher Rotationsfrequenz deutlich höhere Wiederholraten möglich.
Die Vermeidung von Schaltvorgängen durch die Verwendung von Offsetfeldern ermöglicht
es, mit dem ursprünglichem Aufbau auch Partikelsysteme zu untersuchen, deren Relaxationszeit
weit unter 3 ms liegt. Hier zeigt sich, dass sich für unterschiedliche Partikelsysteme teils sehr
charakteristische Signalmuster ergeben. Diese lassen sich grob in drei Kategorien einteilen. Die
erste Kategorie sind suspendierte Eindomänenpartikel mit einer nicht vernachlässigbaren
Relaxationszeit. Hier handelt es sich um das bevorzugte Zielsystem für RDS, das durch die
Langevin-Gleichung beschrieben werden kann. Die zweite Kategorie sind Partikelsysteme, bei
denen die Relaxationsdauer vernachlässigbar ist. In diesem Fall kann der Signalverlauf mit der
Langevinfunktion beschrieben werden. Die dritte Kategorie umfasst alle übrigen Partikelsysteme,
insbesondere Suspensionen von MNP-Clustern, die u.a. aufgrund von Interpartikelwechselwirkung
komplexe Signalverläufe ergeben, die sich praktisch nicht berechnen lassen. Spektroskopische
Untersuchungen sind damit dennoch durch das Anlegen entsprechender Referenzdatenbanken
möglich (Fingerprinting). Multiparametrisches RDS, d.h. die Wiederholung der Messung für z.B.
unterschiedliche Amplituden oder unterschiedliche Viskositäten des Suspensionsmediums, erzeugt
aufgrund mehrerer nichtlinearer Abhängigkeiten massive Unterschiede im resultierenden
multidimensionalen Datensatz. Das verspricht die Erreichbarkeit hoher spektroskopischer
Trennschärfen bei geeigneter Partikel- und Sequenzoptimierung.
Die Simulationen und experimentellen Ergebnisse dieser Arbeit zeigen grundsätzliche
Hürden und Möglichkeiten für das ebenfalls in dieser Arbeit eingeführte RDS auf. Es zeigt damit
grundlegende Aspekte auf, die für die Entwicklung von RDS-Hardware und die Optimierung von
MNP-Suspensionen nötig sind. Mit RDS wird in weiterführenden Arbeiten die Entwicklung von
hochempfindlichen Bioassays und die Erweiterung um die räumliche Kodierung angestrebt (RDI),
da der zugrunde liegende Effekt zugleich sehr vielversprechend als Grundlage für molekulare
Bildgebung ist.
After the discovery of three-dimensional topological insulators (TIs), such as tetradymite chalcogenides Bi$_2$Se$_3$, Bi$_2$Te$_3$ and Sb$_2$Te$_3$ – a new class of quantum materials characterized by their unique surface electronic properties – the solid state community got focused on topological states that are driven by strong electronic correlations and magnetism. An important material class is the magnetic TI (MTI) exhibiting the quantum anomalous Hall (QAH) effect, i.e. a dissipationless quantized edge-state transport in the absence of external magnetic field, originating from the interplay between ferromagnetism and a topologically non-trivial band structure. The unprecedented opportunities offered by these new exotic materials open a new avenue for the development of low-dissipation electronics, spintronics, and quantum computation. However, the major concern with QAH effect is its extremely low onset temperature, limiting its practical application. To resolve this problem, a comprehensive understanding of the microscopic origin of the underlying ferromagnetism is necessary.
V- and Cr-doped (Bi,Sb)$_2$Te$_3$ are the two prototypical systems that have been widely studied as realizations of the QAH state. Finding microscopic differences between the strongly correlated V and Cr impurities would help finding a relevant model of ferromagnetic coupling and eventually provide better control of the QAH effect in these systems. Therefore, this thesis first focuses on the V- and Cr-doped (Bi,Sb)$_2$Te$_3$ systems, to better understand these differences. Exploiting the unique capabilities of x-ray absorption spectroscopy and magnetic circular dichroism (XAS/XMCD), combined with advanced modeling based on multiplet ligand-field theory (MLFT), we provide a detailed microscopic insight into the local electronic and magnetic properties of these systems and determine microscopic parameters crucial for the comparison with theoretical models, which include the $d$-shell filling, spin and orbital magnetic moments. We find a strongly covalent ground state, dominated by the superposition of one and two Te-ligand-hole configurations, with a negligible contribution from a purely ionic 3+ configuration. Our findings indicate the importance of the Te $5p$ states for the ferromagnetism in (Bi, Sb)$_2$Te$_3$ and favor magnetic coupling mechanisms involving $pd$-exchange. Using state-of-the-art density functional theory (DFT) calculations in combination with XMCD and resonant photoelectron spectroscopy (resPES), we reveal the important role of the $3d$ impurity states in mediating magnetic exchange coupling. Our calculations illustrate that the kind and strength of the exchange coupling varies with the impurity $3d$-shell occupation. We find a weakening of ferromagnetic properties upon the increase of doping concentration, as well as with the substitution of Bi at the Sb site. Finally, we qualitatively describe the origin of the induced magnetic moments at the Te and Sb sites in the host lattice and discuss their role in mediating a robust ferromagnetism based on a $pd$-exchange interaction scenario. Our findings reveal important clues to designing higher $T_{\text{C}}$ MTIs.
Rare-earth ions typically exhibit larger magnetic moments than transition-metal ions and thus promise the opening of a wider exchange gap in the Dirac surface states of TIs, which is favorable for the realization of the high-temperature QAH effect. Therefore, we have further focused on Eu-doped Bi$_2$Te$_3$ and scrutinized whether the conditions for formation of a substantial gap in this system are present by combining spectroscopic and bulk characterization methods with theoretical calculations. For all studied Eu doping concentrations, our atomic multiplet analysis of the $M_{4,5}$ x-ray absorption and magnetic circular dichroism spectra reveals a Eu$^{2+}$ valence, unlike most other rare earth elements, and confirms a large magnetic moment. At temperatures below 10 K, bulk magnetometry indicates the onset of antiferromagnetic ordering. This is in good agreement with DFT results, which predict AFM interactions between the Eu impurities due to the direct overlap of the impurity wave functions. Our results support the notion of antiferromagnetism coexisting with topological surface states in rare-earth doped Bi$_2$Te$_3$ and corroborate the potential of such doping to result in an antiferromagnetic TI with exotic quantum properties.
The doping with impurities introduces disorder detrimental for the QAH effect, which may be avoided in stoichiometric, well-ordered magnetic compounds. In the last part of the thesis we have investigated the recently discovered intrinsic magnetic TI (IMTI) MnBi$_6$Te$_{10}$, where we have uncovered robust ferromagnetism with $T_{\text{C}} \approx 12$ K and connected its origin to the Mn/Bi intermixing. Our measurements reveal a magnetically intact surface with a large moment, and with FM properties similar to the bulk, which makes MnBi$_6$Te$_{10}$ a promising candidate for the QAH effect at elevated temperatures. Moreover, using an advanced ab initio MLFT approach we have determined the ground-state properties of Mn and revealed a predominant contribution of the $d^5$ configuration to the ground state, resulting in a $d$-shell electron occupation $n_d = 5.31$ and a large magnetic moment, in excellent agreement with our DFT calculations and the bulk magnetometry data. Our results together with first principle calculations based on the DFT-GGA$+U$, performed by our collaborators, suggest that carefully engineered intermixing plays a crucial role in achieving a robust long-range FM order and therefore could be the key for achieving enhanced QAH effect properties.
We expect our findings to aid better understanding of MTIs, which is essential to help increasing the temperature of the QAH effect, thus facilitating the realization of low-power electronics in the future.