73.43.-f Quantum Hall effects
Refine
Has Fulltext
- yes (2)
Is part of the Bibliography
- yes (2)
Document Type
- Doctoral Thesis (2)
Language
- English (2)
Keywords
- Aharonov-Casher phase (1)
- Aharonov-Casher-Effekt (1)
- Bismutverbindungen (1)
- Elektronischer Transport (1)
- Interferenz <Physik> (1)
- Molekularstrahlepitaxie (1)
- Quanten anomalen Hall-Effekt (1)
- Quanten-Hall-Effekt (1)
- Quanten-Spin-Hall-Effekt (1)
- Quantenwell (1)
- Quantum anomalous Hall effect (1)
- Spin (1)
- Spin-Bahn-Wechselwirkung (1)
- Spin-Hall-Effekt (1)
- Topologischer Isolator (1)
- Zwei-Sechs-Halbleiter (1)
- mesoscopic transport (1)
- mesoskopischer Transport (1)
- narrow-gap semiconductor (1)
- quantum spin Hall effect (1)
- spin Hall effect (1)
- spin-orbit-interaction (1)
Institute
The subject of this thesis is the fabrication and characterization of magnetic topological
insulator layers of (V,Bi,Sb)\(_2\)Te\(_3\) exhibiting the quantum anomalous Hall
effect. A major task was the experimental realization of the quantum anomalous
Hall effect, which is only observed in layers with very specific structural,
electronic and magnetic properties. These properties and their influence on the
quantum anomalous Hall effect are analyzed in detail.
First, the optimal conditions for the growth of pure Bi\(_2\)Te\(_3\) and Sb\(_2\)Te\(_3\) crystal
layers and the resulting structural quality are studied. The crystalline quality of
Bi\(_2\)Te\(_3\) improves significantly at higher growth temperatures resulting in a small
mosaicity-tilt and reduced twinning defects. The optimal growth temperature is
determined as 260\(^{\circ}\)C, low enough to avoid desorption while maintaining a high
crystalline quality.
The crystalline quality of Sb\(_2\)Te\(_3\) is less dependent on the growth temperature.
Temperatures below 230\(^{\circ}\)C are necessary to avoid significant material desorption,
though. Especially for the nucleation on Si(111)-H, a low sticking coefficient is
observed preventing the coalescence of islands into a homogeneous layer.
The influence of the substrate type, miscut and annealing sequence on the growth
of Bi\(_2\)Te\(_3\) layers is investigated. The alignment of the layer changes depending on
the miscut angle and annealing sequence: Typically, layer planes align parallel to
the Si(111) planes. This can enhance the twin suppression due to transfer of the
stacking order from the substrate to the layer at step edges, but results in a step
bunched layer morphology. For specific substrate preparations, however, the layer
planes are observed to align parallel to the surface plane. This alignment avoids
displacement at the step edges, which would cause anti-phase domains. This results
in narrow Bragg peaks in XRD rocking curve scans due to long-range order in
the absence of anti-phase domains. Furthermore, the use of rough Fe:InP(111):B
substrates leads to a strong reduction of twinning defects and a significantly reduced
mosaicity-twist due to the smaller lattice mismatch.
Next, the magnetically doped mixed compound V\(_z\)(Bi\(_{1−x}\)Sb\(_x\))\(_{2−z}\)Te\(_3\) is studied in
order to realize the quantum anomalous Hall effect. The addition of V and Bi to
Sb\(_2\)Te\(_3\) leads to efficient nucleation on the Si(111)-H surface and a closed, homogeneous
layer. Magneto-transport measurements of layers reveal a finite anomalous
Hall resistivity significantly below the von Klitzing constant. The observation of
the quantum anomalous Hall effect requires the complete suppression of parasitic
bulklike conduction due to defect induced carriers. This can be achieved by optimizing
the thickness, composition and growth conditions of the layers.
The growth temperature is observed to strongly influence the structural quality.
Elevated temperatures result in bigger islands, improved crystallographic orientation
and reduced twinning. On the other hand, desorption of primarily Sb is
observed, affecting the thickness, composition and reproducibility of the layers.
At 190\(^{\circ}\)C, desorption is avoided enabling precise control of layer thickness and
composition of the quaternary compound while maintaining a high structural
quality.
It is especially important to optimize the Bi/Sb ratio in the (V,Bi,Sb)\(_2\)Te\(_3\) layers,
since by alloying n-type Bi\(_2\)Te\(_3\) and p-type Sb\(_2\)Te\(_3\) charge neutrality is achieved at
a specific mixing ratio. This is necessary to shift the Fermi level into the magnetic
exchange gap and fully suppress the bulk conduction. The Sb content x furthermore
influences the in-plane lattice constant a significantly. This is utilized to
accurately determine x even for thin films below 10 nm thickness required for the
quantum anomalous Hall effect. Furthermore, x strongly influences the surface
morphology: with increasing x the island size decreases and the RMS roughness
increases by up to a factor of 4 between x = 0 and x = 1.
A series of samples with x varied between 0.56-0.95 is grown, while carefully
maintaining a constant thickness of 9 nm and a doping concentration of 2 at.% V.
Magneto-transport measurements reveal the charge neutral point around x = 0.86
at 4.2 K. The maximum of the anomalous Hall resistivity of 0.44 h/e\(^2\) is observed
at x = 0.77 close to charge neutrality. Reducing the measurement temperature
to 50 mK significantly increases the anomalous Hall resistivity. Several samples
in a narrow range of x between 0.76-0.79 show the quantum anomalous Hall effect
with the Hall resistivity reaching the von Klitzing constant and a vanishing
longitudinal resistivity. Having realized the quantum anomalous Hall effect as the
first group in Europe, this breakthrough enabled us to study the electronic and
magnetic properties of the samples in close collaborations with other groups.
In collaboration with the Physikalisch-Technische Bundesanstalt high-precision
measurements were conducted with detailed error analysis yielding a relative de-
viation from the von Klitzing constant of (0.17 \(\pm\) 0.25) * 10\(^{−6}\). This is published
as the smallest, most precise value at that time, proving the high quality of the
provided samples. This result paves the way for the application of magnetic topological
insulators as zero-field resistance standards.
Non-local magneto-transport measurements were conducted at 15 mK in close
collaboration with the transport group in EP3. The results prove that transport
happens through chiral edge channels. The detailed analysis of small anomalies in
transport measurements reveals instabilities in the magnetic phase even at 15 mK.
Their time dependent nature indicates the presence of superparamagnetic contributions
in the nominally ferromagnetic phase.
Next, the influence of the capping layer and the substrate type on structural properties
and the impact on the quantum anomalous Hall effect is investigated. To
this end, a layer was grown on a semi-insulating Fe:InP(111)B substrate using the
previously optimized growth conditions. The crystalline quality is improved significantly
with the mosaicity twist reduced from 5.4\(^{\circ}\) to 1.0\(^{\circ}\). Furthermore, a layer
without protective capping layer was grown on Si and studied after providing sufficient
time for degradation. The uncapped layer on Si shows perfect quantization,
while the layer on InP deviates by about 5%. This may be caused by the higher
crystalline quality, but variations in e.g. Sb content cannot be ruled out as the
cause. Overall, the quantum anomalous Hall effect seems robust against changes
in substrate and capping layer with only little deviations.
Furthermore, the dependence of the quantum anomalous Hall effect on the thickness
of the layers is investigated. Between 5-8 nm thickness the material typically
transitions from a 2D topological insulator with hybridized top and bottom surface
states to a 3D topological insulator. A set of samples with 6 nm, 8 nm, and
9 nm thickness exhibits the quantum anomalous Hall effect, while 5 nm and 15 nm
thick layers show significant bulk contributions. The analysis of the longitudinal
and Hall conductivity during the reversal of magnetization reveals distinct differences
between different thicknesses. The 6 nm thick layer shows scaling consistent
with the integer quantum Hall effect, while the 9 nm thick layer shows scaling expected
for the topological surface states of a 3D topological insulator. The unique
scaling of the 9 nm thick layer is of particular interest as it may be a result of
axion electrodynamics in a 3D topological insulator.
Subsequently, the influence of V doping on the structural and magnetic properties
of the host material is studied systematically. Similarly to Bi alloying, increased
V doping seems to flatten the layer surface significantly. With increasing V content,
Te bonding partners are observed to increase simultaneously in a 2:3 ratio
as expected for V incorporation on group-V sites. The linear contraction of the
in-plane and out-of-plane lattice constants with increasing V doping is quantitatively
consistent with the incorporation of V\(^{3+}\) ions, possibly mixed with V\(^{4+}\)
ions, at the group-V sites. This is consistent with SQUID measurements showing
a magnetization of 1.3 \(\mu_B\) per V ion.
Finally, magnetically doped topological insulator heterostructures are fabricated
and studied in magneto-transport. Trilayer heterostructures with a non-magnetic
(Bi,Sb)\(_2\)Te\(_3\) layer sandwiched between two magnetically doped layers are predicted
to host the axion insulator state if the two magnetic layers are decoupled and in
antiparallel configuration. Magneto-transport measurements of such a trilayer heterostructure
with 7 nm undoped (Bi,Sb)\(_2\)Te\(_3\) between 2 nm thick layers doped with
1.5 at.% V exhibit a zero Hall plateau representing an insulating state. Similar results
in the literature were interpreted as axion insulator state, but in the absence
of a measurement showing the antiparallel magnetic orientation other explanations
for the insulating state cannot be ruled out.
Furthermore, heterostructures including a 2 nm thin, highly V doped layer region
show an anomalous Hall effect of opposite sign compared to previous samples. A
dependency on the thickness and position of the doped layer region is observed,
which indicates that scattering at the interfaces causes contributions to the anomalous
Hall effect of opposite sign compared to bulk scattering effects.
Many interesting phenomena in quantum anomalous Hall insulators as well as axion
insulators are still not unambiguously observed. This includes Majorana bound
states in quantum anomalous Hall insulator/superconductor hybrid systems and
the topological magneto-electric effect in axion insulators. The limited observation
temperature of the quantum anomalous Hall effect of below 1 K could be increased
in 3D topological insulator/magnetic insulator heterostructures which utilize the
magnetic proximity effect.
The main achievement of this thesis is the reproducible growth and characterization
of (V,Bi,Sb)2Te3 layers exhibiting the quantum anomalous Hall effect. The
detailed study of the structural requirements of the quantum anomalous Hall effect
and the observation of the unique axionic scaling behavior in 3D magnetic
topological insulator layers leads to a better understanding of the nature of this
new quantum state. The high-precision measurements of the quantum anomalous
Hall effect reporting the smallest deviation from the von Klitzing constant
are an important step towards the realization of a zero-field quantum resistance
standard.
Within the scope of this thesis, spin related transport phenomena have been investigated in HgTe/HgCdTe quantum well structures. This material exhibits peculiar band structure properties, which result in a strong spin-orbit interaction of the Rashba type. An inverted band structure, i.e., a reversed ordering of the energy states in comparison to common semiconductors, is obtained for quantum well layers above a critical thickness. Furthermore, the band structure properties can be controlled in the experiments by moderate gate voltages. Most prominently, the type of carriers in HgTe quantum wells can be changed from n to p due to the narrow energy gap. Along with the inverted band structure, this unique transition is the basis for the demonstration of the Quantum Spin Hall state, which is characterized by the existence of two one-dimensional spin-polarized edge states propagating in opposite directions, while the Fermi level in the bulk is in the energy gap. Since elastic scattering is suppressed by time reversal symmetry, a quantized conductance for charge and spin transport is predicted. Our experiments provide the first experimental demonstration of the QSH state. For samples with characteristic dimensions below the inelastic mean free path, charge conductance close to the expected value of 2e^2/h has been observed. Strong indication for the edge state transport was found in the experiments as well. For large samples, potential fluctuations lead to the appearance of local n-conducting regions which are considered to be the dominant source of backscattering. When time reversal symmetry is broken in a magnetic field, elastic scattering becomes possible and conductance is significantly suppressed. The suppression relies on a dominant orbital effect in a perpendicular field and a smaller Zeeman-like effect present for any field direction. For large perpendicular fields, a re-entrant quantum Hall state appears. This unique property is directly related to the non-trivial QSH insulator state. While clear evidence for the properties of charge transport was provided, the spin properties could not be addressed. This might be the goal of future experiments. In another set of experiments, the intrinsic spin Hall effect was studied. Its investigation was motivated by the possibility to create and to detect pure spin currents and spin accumulation. A non-local charging attributed to the SHE has been observed in a p-type H-shaped structure with large SO interaction, providing the first purely electrical demonstration of the SHE in a semiconductor system. A possibly more direct way to study the spin Hall effects opens up when the spin properties of the QSH edge states are taken into account. Then, the QSH edge states can be used either as an injector or a detector of spin polarization, depending on the actual configuration of the device. The experimental results indicate the existence of both intrinsic SHE and the inverse SHE independently of each other. If a spin-polarized current is injected from the QSH states into a region with Rashba SO interaction, the precession of the spin can been observed via the SHE. Both the spin injection and precession might be used for the realization of a spin-FET similar to the one proposed by Datta and Das. Another approach for the realization of a spin-based FET relies on a spin-interference device, in which the transmission is controlled via the Aharonov-Casher phase and the Berry phase, both due to the SO interaction. In the presented experiments, ring structures with tuneable SO coupling were studied. A complex interference pattern is observed as a function of external magnetic field and gate voltage. The dependence on the Rashba splitting is attributed to the Aharonov-Casher phase, whereas effects due to the Berry phase remain unresolved. This interpretation is confirmed by theoretical calculations, where multi-channel transport through the device has been assumed in agreement with the experimental results. Thus, our experiments provide the first direct observation of the AC effect in semiconductor structures. In conclusion, HgTe quantum well structures have proven to be an excellent template for studying spin-related transport phenomena: The QSHE relies on the peculiar band structure of the material and the existence of both the SHE and the AC effect is a consequence of the substantial spin-orbit interaction. While convincing results have been obtained for the various effects, several questions can not be fully answered yet. Some of them may be addressed by more extensive studies on devices already available. Other issues, however, ask, e.g., for further advances in sample fabrication or new approaches by different measurements techniques. Thus, future experiments may provide new, compelling insights for both the effects discussed in this thesis and, more generally, other spin-orbit related transport properties.