Refine
Has Fulltext
- yes (20)
Is part of the Bibliography
- yes (20)
Year of publication
Document Type
- Doctoral Thesis (20)
Keywords
- Organischer Halbleiter (20) (remove)
Institute
- Physikalisches Institut (20) (remove)
ResearcherID
- D-1250-2010 (1)
The approach of using the combination of Ultraviolet (UPS) and Inverse Photoemission (IPS) to determine the transport levels in thin films of organic semiconductors is the scope of this work. For this matter all influences on the peak position and width in Photoelectron Spectroscopy are discussed with a special focus on organic semiconductors. Many of these influences are shown with experimental results of the investigation of diindenoperylene on Ag(111). These findings are applied to inorganic semiconductors silicon in order to establish the use of UPS and IPS on a well-understood system. Finally, the method is used to determine the transport level of several organic semiconductors (PTCDA, Alq3, CuPc, DIP, PBI-H4) and the corresponding exciton binding energies are calculated by comparison to optical absorption data.
The thesis investigates the electrical transport properties of different π-conjugated organic semiconductors applied as active semiconducting material in organic field-effect transistor (OFET) devices. Theses organic materials are αω-dihexylquaterthiophene (DH4T), the tetrathiafulvalene (TTF) derivatives dibenzene-tetrathiafulvalene (DB-TTF) and dithiophene-tetrathiafulvalene (DT-TTF), and polytriarylamine (PTAA). The latter material is an amorphous polymer, the three others are small molecule oligomer materials. Different deposition methods were applied and compared. The investigations in the thesis treat the pure characterisation of the above materials with their different properties in OFET devices. Furthermore, the aim was to observe and analyse general rules and effects in OFETs depending on the structure, previous history, and the device scaling. Therefore, different tools and special analysing methods were developed and applied. These are a standard characterisation method for the classification of the used organic semiconductor, temperature dependent electrical characterisation investigating the electrical transport properties, the newly developed in situ measurement method of OFET devices, the downscaling of the OFET devices of channel length below 100 nm, and the lithographical structuring of a PTAA film.
Einfluss metallischer Nanostrukturen auf die optoelektronischen Eigenschaften organischer Halbleiter
(2018)
Opto-elektronische Bauelemente auf Basis organischer Moleküle haben in den letzten Jahren nicht nur in Nischenbereichen, wie der Kombination organischer Photovoltaik mit gebäudeintegrierten Konzepten, sondern vor allem auch in der Entwicklung von kommerziell verfügbaren OLED (organische lichtemittierende Dioden) Bauteilen, wie 4K TV-Geräten und Handy Displays, an Bedeutung gewonnen. Im Vergleich zu anorganischen Bauteilen weisen jedoch vor allem organische Solarzellen noch weitaus geringere Effizienzen auf, weswegen die Erforschung ihrer Funktionsweise und der Einflüsse der einzelnen Bestandteile auf mikroskopischer Ebene für die Weiterentwicklung und Verbesserung des Leistungspotentials dieser Technologie unabdingbar ist. \\
Um dies zu erreichen, wurde in dieser Arbeit die Wechselwirkung zwischen der lokalisierten Oberflächenplasmonenresonanz (LSPR) metallischer Nanopartikel mit den optischen Anregungen organischer Dünnschichten in dafür eigens präparierten opto-elektronischen Hybrid-Bauteilen aus kleinen Molekülen untersucht. Durch die Implementierung und Kopplung an solche plasmonischen Nanostrukturen kann die Absorption bzw. Emission durch das lokal um die Strukturen erhöhte elektrische Feld gezielt beeinflusst werden. Hierbei ist der spektrale Überlapp zwischen LSPR und den Absorptions- bzw. E\-missions\-spek\-tren der organischen Emitter entscheidend. In dieser Arbeit wurden durch Ausnutzen dieses Mechanismus sowohl die Absorption in organischen photovoltaischen Zellen erhöht, als auch eine verstärkte Emission in nanostrukturierten OLEDs erzeugt. \\
Besonderer Fokus wurde bei diesen Untersuchungen auf mikroskopische Effekte durch neu entstehende Grenzflächen und die sich verändernden Morphologien der aktiven organischen Schichten gelegt, da deren Einflüsse bei optischen Untersuchungen oftmals nur unzureichend berücksichtigt werden. In der Arbeit wurden daher die nicht zu vernachlässigenden Folgen der Einbringung von metallischen Nanostrukturen auf die Morphologie und Grenzflächen zusammen mit den spektralen Veränderungen der Absorptions- und Emissionscharakteristik organischer Moleküle analysiert und in Zusammenhang gebracht, wodurch eine Verbesserung der Effizienzen opto-elektronischer Bauteile erreicht werden soll.
In the presented thesis, the various excited states encountered in conjugated organic semiconductors are investigated with respect to their utilization in organic thin-film solar cells. Most of these states are spin-baring and can therefore be addressed by means of magnetic resonance spectroscopy. The primary singlet excitation (spin 0), as well as positive and negative polaronic charge carriers (spin 1/2) are discussed. Additionally, triplet excitons (spin 1) and charge transfer complexes are examined, focussing on their differing spin-spin interaction strength. For the investigation of these spin-baring states especially methods of electron paramagnetic resonance (EPR) are best suited. Therefore according experimental methods were implemented in the course of this work to study conjugated polymers, fullerenes and their blends with continuous wave as well as time-resolved EPR and optically detected magnetic resonance.
The transport of optically excited states, called excitons, as well as their conversion into charges define the two major steps allowing for the operation of organic photovoltaic (OPV) devices. Hence, a deep understanding of these processes, the involved mechanisms as well as possible loss channels is crucial for further improving the efficiency of organic solar cells. For studying the aforementioned processes spectroscopic methods like absorption and emission measurements are useful tools. As many of the processes take place on a sub-nanosecond (ns) timescale ultrafast spectroscopic methods are required. Due to this reason two experiments based on a femtosecond laser system were built and employed in this work, namely picosecond (ps) time-resolved photoluminescence (PL) and transient absorption (TA) spectroscopy.
By analyzing the PL decay dynamics in the prototypical organic semiconductor rubrene, the feasibility of a new approach for improving the efficiency of organic solar cells by harvesting triplet excitons generated by singlet fission was examined. Singlet fission describes a process where two triplet excitons are generated via a photoexcited singlet exciton precursor state if the energy of the two triplets is comparable with the energy of the singlet. For this purpose the influence of characteristic length scales on the exciton dynamics in different rubrene morphologies exhibiting an increasing degree of confinement was analyzed. The results show that the quenching at interfacial states efficiently suppresses the desired fission process if these states are reached by excitons during migration. Since interfacial states are expected to play a significant role in thin film solar cells and are easily accessible for the migrating excitons, the results have to be considered for triplet-based OPV.
While the aforementioned approach is only investigated for model systems so far, the efficiency of disordered organic bulk heterojunction (BHJ) solar cells could be significantly enhanced in the last couple of years by employing new and more complex copolymer donor materials. However, little is known about the photophysics and in particular the excitation dynamics of these systems. By carrying out a systematic optical study on the prominent copolymer PCDTBT and its building blocks we were able to identify the nature of the two characteristic absorption bands and the coupling mechanism between these levels. The latter mechanism is based on an intrachain partial charge transfer between two functional subunits and our time-resolved measurements indicate that this coupling governs the photophysical properties of solar cells based on these copolymers. The efficient coupling of functional subunits can be seen as a key aspect that guarantees for the success of the copolymer approach.
Another important issue concerns the optimization of the morphology of BHJ solar cells. It arises from the discrepancy between the exciton diffusion length \mbox{($\approx$ 10 nm)} and the absorption length of solar irradiation ($\approx$ 100 nm). Due to this reason, even for devices based on new copolymer materials, processing parameters affecting the morphology like annealing or employing processing additives are of major importance. In our combined optical, electrical and morphological study for solar cells based on the high-efficient copolymer PBDTTT-C we find a direct correlation between additive content and intermixing of the active layer. The observed maximum in device efficiency can be attributed to a morphology guaranteeing for an optimized balance between charge generation and transport. Our results highlight the importance of understanding the influence of processing parameters on the morphology of the BHJ and thus on the efficiency of the device.
Exziton-Polaritonen sind hybride Quasiteilchen, die entstehen durch die starke Kopplung zwischen Halbleiter-Exzitonen und Mikrokavitätsphotonen in einem optischen Resonator. Aufgrund ihres bosonischen Charakters können die Polaritonen Kondensate ausbilden. In dieser Arbeit ist der emittierende organische Halbleiter das fluoreszierende Protein mCherry. Um einen räumlichen Einschluss zu generieren wurden hemisphärische Potentiale genutzt. Durch die Variation der Potentiallandschaft (Linse, Molekül, Kette, Su-Schrieffer-Heeger-Kette und Honigwaben-Gitter) konnten Eigenschaften wie beispielsweise topologisch nicht-triviale Defekte experimentell bei Umgebungstemperatur demonstriert werden. Zusammengefasst beschäftigt sich diese Arbeit mit der Exziton-Polartion Kondensation in unterschiedlichen Potentiallandschaften mit dem organischen Halbleiter mCherry.
The focus of this work is studying recombination mechanisms occurring in organic solar cells, as well as their impact on one of their most important parameters — the open circuit voltage Voc.
Firstly, the relationship between Voc and the respective charge carrier density n in the active layer under open circuit conditions is analyzed. Therefor, a model after Shockley for the open circuit voltage is used, whose validity is proven with the aid of fits to the measured data. Thereby, it is emphasized that the equation is only valid under special conditions. In the used reference system P3HT:PC61BM the fits are in agreement with the measurement data only in the range of high temperatures (150 - 300 K), where Voc increases linearly with decreasing temperature. At lower temperatures (50 – 150 K), the experiment shows a saturation of Voc. This saturation cannot be explained with the model by the measured falling charge carrier density with decreasing temperatures. In this temperature range Voc is not directly related to the intrinsic properties of the active layer. Voc saturation is due to injection energy barriers at the contacts, which is ascertained by macroscopic simulations. Furthermore, it is observed that Voc in the case of saturation is equivalent to the so-called built-in potential. The difference between the built-in potential and the energy gap corresponds thereby to the sum of the energy barriers at both contacts.
With the knowledge of the Voc(n) dependency for not contact limited solar cells, it is possible to investigate the recombination mechanisms of charge carriers in the active layer. For Langevin recombination the recombination rate is Rn2 (recombination order RO = 2), for Shockley-Read-Hall (SRH) Rn1 (RO=1); in various publications RO higher than two is reported with two main explanations.
1: Trap states for charge carriers exist in the respective separated phases, i.e. electrons in the acceptor phase and holes in the donor phase, which leads to a delayed recombination of the charge carriers at the interface of both phases and finally to an apparent recombination order higher than 2.
2: The enhanced R(n) dependency is attributed to the so called recombination prefactor, which again is dependent from n dependent mobility µ.
It is shown that for the system P3HT:PC61BM at room temperature the µ(n) dependency does nearly completely explain the higher RO but not at lower temperatures which in this case supports the first explanation. In the material system PTB7:PC71BM the increased RO cannot be explained by the µ(n) dependency even at room temperature.
To support the importance of trap states in combination with a phase separation for the explanation of the enhanced RO, additional trap states were incorporated in the solar cells to investigate their influence on the recombination mechanisms. To achieve this, P3HT:PC61BM solar cells were exposed to synthetic air (in the dark and under illumination) or TCNQ was added in small concentrations to the active layer which act as electron traps. For the oxygen degraded solar cell the recombination order is determined by a combination of open Voc-transients and Voc(n) measurements. Thereby, a continuous increase of the recombination order from 2.4 to more than 5 is observed with higher degradation times. By the evaluation of the ideality factor it can be shown that the impact of SRH recombination is increasing with higher trap concentration in relation to Langevin recombination. A similar picture is revealed for solar cells with TCNQ as extrinsic trap states.
Finally, a phenomenon called s-shaped IV-curves is investigated, which can sometimes occur for solar cells under illumination. As course of this a reduced surface recombination velocity can be found. Experimentally, the solar cells were fabricated using a special plasma treatment of the ITO contact. The measured IV-curves of such solar cells are reproduced by macroscopic simulations, where the surface recombination velocity is reduced. Hereby, it has to be distinguished between the surface recombination of majority and minority charge carriers at the respective contacts. The theory can be experimentally confirmed by illumination level dependent IV-curves as well as short circuit current density and open circuit voltage transients.
This thesis focused on the influence of the underlying crystal structure and hence, of the mutual molecular orientation, on the excited states in ordered molecular aggregates. For this purpose, two model systems have been investigated. In the prototypical donor-acceptor complex pentacene-perfluoropentacene (PEN-PFP) the optical accessibility of the charge transfer state and the possibility to fabricate highly defined interfaces by means of single crystal templates enabled a deep understanding of the spatial anisotropy of the charge transfer state formation. Transferring the obtained insights to the design of prototypical donor-acceptor devices, the importance of interface control to minimize the occurrence of charge transfer traps and thereby, to improve the device performance, could be demonstrated. The use of zinc phthalocyanine (ZnPc) allowed for the examination of the influence of molecular packing on the excited electronic states without a change in molecular species by virtue of its inherent polymorphism. Combining structural investigations, optical absorption and emission spectroscopy, as well as Franck-Condon modeling of emission spectra revealed the nature of the optical excited state emission in relation to the structural \(\alpha \) and \(\beta \) phase over a wide temperature range from 4 K to 300 K. As a results, the phase transition kinetics of the first order \(\alpha \rightarrow \beta\) phase transition were characterized in depth and applied to the fabrication of prototypical dual luminescent OLEDs.
In this work, the trap states in the conjugated polymer P3HT, often used as electron donor in organic bulk heterojunction solar cells, three commonly used fullerene based electron acceptors and P3HT:PC61BM blends were investigated. Furthermore, the trap states in the blend were compared with these of the pure materials. Concerning the lifetime of organic solar cells the influence of oxygen on P3HT and P3HT:PC61BM blends was studied. The experimental techniques used to investigate the trap states in the organic semiconductors were (fractional) thermally stimulated current (TSC) and current based deep level transient spectroscopy (Q-DLTS). Fractional TSC measurements on P3HT diodes revealed a quasi-continuous trap distribution. The distribution suggested two different traps in P3HT with approximately Gaussian energy distributions and maxima at about 50 meV and 105 meV. Thereby, the former was attributed to the tail states within the regular Gaussian density of states due to the low activation energy. The latter, deeper traps, however, exhibited a strong dependence on oxygen. Exposure of the P3HT diodes to oxygen, ambient air and synthetic (dry) air all revealed an increase of the deeper traps density with exposure time in the same manner. While the lower limit of the trap density in non aged P3HT samples was in the range of (1.0 − 1.2)×10^22 m^−3, it was more than doubled after an exposure of 50 h to air. An increase of the trap density with oxygen exposure time was also seen in the Q-DLTS measurements accompanied with an increase of the temperature dependence of the emission rates, indicating an enhanced formation of deeper traps. Due to the raise in density of the deeper traps, the charge carrier mobility in P3HT significantly decreased, as revealed by photo-CELIV measurements, resulting in a loss in mobility of about two orders of magnitude after 100 h exposure to synthetic air. The increased trap density was attributed to p-doping of P3HT by the transfer of an electron to adsorbed oxygen. This effect was partially reversible by applying vacuum to the sample for several hours or, more significantly, by a thermal treatment of the devices in nitrogen atmosphere. The trap states in the methanofullerenes PC61BM, bisPC61BM and PC71BM were investigated by TSC measurements. PC61BM yielded a broad quasi-continuous trap distribution with the maximum of the distribution at about 75 meV. The comparison of the TSC spectra of the three methanofullerenes exhibited significant differences in the trap states with higher activation energies of the most prominent traps in bisPC61BM and PC71BM compared to PC61BM. This probably originates from the different isomers bisPC61BM and PC71BM consist of. Each of the isomers yields different LUMO energies, where the lower ones can act as traps. The lower limit of the trap density of all of the three investigated fullerene derivatives exhibited values in the order of 10^22 m^−3, with the highest for bisPC61BM and the lowest for PC61BM. By applying fractional TSC measurements on P3HT:PC61BM solar cells, it was shown that the trap distribution in the blend is a superposition of the traps in pure P3HT and PC61BM and additional deeper traps in the range of about 250 meV to 400 meV. The origin of these additional traps, which can not be related to the pure materials, was attributed to a higher disorder in the blend and P3HT/PC61BM interfaces. This conclusion was supported by standard TSC and Q-DLTS measurements performed on pristine and annealed P3HT:PC61BM blends, exhibiting a higher ratio of the deep traps in the pristine samples. The lower limit of the trap density of the investigated annealed solar cells was in the range of (6−8)×10^22 m^−3, which was considerably higher than in the pure materials. The influence of oxygen on P3HT:PC61BM solar cells was investigated by exposure of the devices to synthetic air under specific conditions. Exposure of the solar cells to oxygen in the dark resulted in a strong decrease in the power conversion efficiency of 60 % within 120 h, which was only caused by a loss in short-circuit current. Simultaneous illumination of the solar cells during oxygen exposure strongly accelerated the degradation, resulting in an efficiency loss of 30 % within only 3 h. Thereby, short-circuit current, open-circuit voltage and fill factor all decreased in the same manner. TSC measurements revealed an increase of the density of deeper traps for both degradation conditions, which resulted in a decrease of the mobility, as investigated by CELIV measurements. However, these effects were less pronounced than in pure P3HT. Furthermore, an increase of the equilibrium charge carrier density with degradation time was observed, which was attributed to oxygen doping of P3HT. With the aid of macroscopic simulations, it was shown that the doping of the solar cells is the origin of the loss in short-circuit current for both degradation conditions.
Um die Natur der Transportdynamik von Ladungsträgern auch auf mikroskopischen Längenskalen nicht-invasiv untersuchen zu können, wurde im ersten Schwerpunkt dieser Arbeit das PL- (Photolumineszenz-) Quenching (engl.: to quench: löschen; hier: strahlungslose Rekombination von Exzitonen) in einer organischen Dünnschicht durch die injizierten und akkumulierten Löcher in einer Transistorgeometrie analysiert. Diese Zusammenführung zweier Methoden - der elektrischen Charakterisierung von Dünnschichttransistoren und der Photolumineszenzspektroskopie - erfasst die Änderung des strahlenden Zerfalls von Exzitonen infolge der Wechselwirkung mit Ladungsträgern. Dadurch werden räumlich aufgelöste Informationen über die Ladungsverteilung und deren Spannungsabhängigkeit im Transistorkanal zugänglich. Durch den Vergleich mit den makroskopischen elektrischen Kenngrößen wie der Schwell- oder der Turn-On-Spannung kann die Funktionsweise der Transistoren damit detaillierter beschrieben werden, als es die Kenngrößen alleine ermöglichen. Außerdem wird die Quantifizierung dieser mikroskopischen Interaktionen möglich, welche beispielsweise als Verlustkanal in organischen Photovoltaikzellen und organicshen Leuchtdioden auftreten können. Die Abgrenzung zu anderen dissipativen Prozessen, wie beispielsweise der Exziton-Exziton Annihilation, Ladungsträgerrekombination, Triplett-Übergänge oder Rekombination an Störstellen oder metallischen Grenzflächen, erlaubt die detaillierte Analyse der Wechselwirkung von optisch angeregten Zuständen mit Elektronen und Löchern.
Im zweiten Schwerpunkt dieser Arbeit werden die Transporteigenschaften des Naphthalindiimids Cl2-NDI betrachtet, bei dem der molekulare Überlapp sowie die Reorganisationsenergie in derselben Größenordnung von etwa 0,1 eV liegen. Um experimentell auf den mikroskopischen Transport zu schließen, werden nach der Optimierung des Kristallwachstums Einkristalltransistoren hergestellt, mit Hilfe derer die Beweglichkeit entlang verschiedener kristallographischer Richtungen als Funktion der Temperatur gemessen werden kann. Die einkristalline Natur der Proben und die spezielle Transistorgeometrie ermöglichen die Analyse der räumlichen Anisotropie des Stromflusses. Der gemessene Beweglichkeitstensor wird daraufhin mit simulierten Tensoren auf der Basis von Levich-Jortner Raten verglichen, um auf den zentralen Ladungstransfermechanismus zu schließen.