Refine
Has Fulltext
- yes (24)
Is part of the Bibliography
- yes (24)
Year of publication
Document Type
- Doctoral Thesis (24)
Keywords
- Organischer Halbleiter (24) (remove)
Institute
ResearcherID
- D-1250-2010 (1)
The focus of this work is studying recombination mechanisms occurring in organic solar cells, as well as their impact on one of their most important parameters — the open circuit voltage Voc.
Firstly, the relationship between Voc and the respective charge carrier density n in the active layer under open circuit conditions is analyzed. Therefor, a model after Shockley for the open circuit voltage is used, whose validity is proven with the aid of fits to the measured data. Thereby, it is emphasized that the equation is only valid under special conditions. In the used reference system P3HT:PC61BM the fits are in agreement with the measurement data only in the range of high temperatures (150 - 300 K), where Voc increases linearly with decreasing temperature. At lower temperatures (50 – 150 K), the experiment shows a saturation of Voc. This saturation cannot be explained with the model by the measured falling charge carrier density with decreasing temperatures. In this temperature range Voc is not directly related to the intrinsic properties of the active layer. Voc saturation is due to injection energy barriers at the contacts, which is ascertained by macroscopic simulations. Furthermore, it is observed that Voc in the case of saturation is equivalent to the so-called built-in potential. The difference between the built-in potential and the energy gap corresponds thereby to the sum of the energy barriers at both contacts.
With the knowledge of the Voc(n) dependency for not contact limited solar cells, it is possible to investigate the recombination mechanisms of charge carriers in the active layer. For Langevin recombination the recombination rate is Rn2 (recombination order RO = 2), for Shockley-Read-Hall (SRH) Rn1 (RO=1); in various publications RO higher than two is reported with two main explanations.
1: Trap states for charge carriers exist in the respective separated phases, i.e. electrons in the acceptor phase and holes in the donor phase, which leads to a delayed recombination of the charge carriers at the interface of both phases and finally to an apparent recombination order higher than 2.
2: The enhanced R(n) dependency is attributed to the so called recombination prefactor, which again is dependent from n dependent mobility µ.
It is shown that for the system P3HT:PC61BM at room temperature the µ(n) dependency does nearly completely explain the higher RO but not at lower temperatures which in this case supports the first explanation. In the material system PTB7:PC71BM the increased RO cannot be explained by the µ(n) dependency even at room temperature.
To support the importance of trap states in combination with a phase separation for the explanation of the enhanced RO, additional trap states were incorporated in the solar cells to investigate their influence on the recombination mechanisms. To achieve this, P3HT:PC61BM solar cells were exposed to synthetic air (in the dark and under illumination) or TCNQ was added in small concentrations to the active layer which act as electron traps. For the oxygen degraded solar cell the recombination order is determined by a combination of open Voc-transients and Voc(n) measurements. Thereby, a continuous increase of the recombination order from 2.4 to more than 5 is observed with higher degradation times. By the evaluation of the ideality factor it can be shown that the impact of SRH recombination is increasing with higher trap concentration in relation to Langevin recombination. A similar picture is revealed for solar cells with TCNQ as extrinsic trap states.
Finally, a phenomenon called s-shaped IV-curves is investigated, which can sometimes occur for solar cells under illumination. As course of this a reduced surface recombination velocity can be found. Experimentally, the solar cells were fabricated using a special plasma treatment of the ITO contact. The measured IV-curves of such solar cells are reproduced by macroscopic simulations, where the surface recombination velocity is reduced. Hereby, it has to be distinguished between the surface recombination of majority and minority charge carriers at the respective contacts. The theory can be experimentally confirmed by illumination level dependent IV-curves as well as short circuit current density and open circuit voltage transients.
This thesis focused on the influence of the underlying crystal structure and hence, of the mutual molecular orientation, on the excited states in ordered molecular aggregates. For this purpose, two model systems have been investigated. In the prototypical donor-acceptor complex pentacene-perfluoropentacene (PEN-PFP) the optical accessibility of the charge transfer state and the possibility to fabricate highly defined interfaces by means of single crystal templates enabled a deep understanding of the spatial anisotropy of the charge transfer state formation. Transferring the obtained insights to the design of prototypical donor-acceptor devices, the importance of interface control to minimize the occurrence of charge transfer traps and thereby, to improve the device performance, could be demonstrated. The use of zinc phthalocyanine (ZnPc) allowed for the examination of the influence of molecular packing on the excited electronic states without a change in molecular species by virtue of its inherent polymorphism. Combining structural investigations, optical absorption and emission spectroscopy, as well as Franck-Condon modeling of emission spectra revealed the nature of the optical excited state emission in relation to the structural \(\alpha \) and \(\beta \) phase over a wide temperature range from 4 K to 300 K. As a results, the phase transition kinetics of the first order \(\alpha \rightarrow \beta\) phase transition were characterized in depth and applied to the fabrication of prototypical dual luminescent OLEDs.
In this work, the trap states in the conjugated polymer P3HT, often used as electron donor in organic bulk heterojunction solar cells, three commonly used fullerene based electron acceptors and P3HT:PC61BM blends were investigated. Furthermore, the trap states in the blend were compared with these of the pure materials. Concerning the lifetime of organic solar cells the influence of oxygen on P3HT and P3HT:PC61BM blends was studied. The experimental techniques used to investigate the trap states in the organic semiconductors were (fractional) thermally stimulated current (TSC) and current based deep level transient spectroscopy (Q-DLTS). Fractional TSC measurements on P3HT diodes revealed a quasi-continuous trap distribution. The distribution suggested two different traps in P3HT with approximately Gaussian energy distributions and maxima at about 50 meV and 105 meV. Thereby, the former was attributed to the tail states within the regular Gaussian density of states due to the low activation energy. The latter, deeper traps, however, exhibited a strong dependence on oxygen. Exposure of the P3HT diodes to oxygen, ambient air and synthetic (dry) air all revealed an increase of the deeper traps density with exposure time in the same manner. While the lower limit of the trap density in non aged P3HT samples was in the range of (1.0 − 1.2)×10^22 m^−3, it was more than doubled after an exposure of 50 h to air. An increase of the trap density with oxygen exposure time was also seen in the Q-DLTS measurements accompanied with an increase of the temperature dependence of the emission rates, indicating an enhanced formation of deeper traps. Due to the raise in density of the deeper traps, the charge carrier mobility in P3HT significantly decreased, as revealed by photo-CELIV measurements, resulting in a loss in mobility of about two orders of magnitude after 100 h exposure to synthetic air. The increased trap density was attributed to p-doping of P3HT by the transfer of an electron to adsorbed oxygen. This effect was partially reversible by applying vacuum to the sample for several hours or, more significantly, by a thermal treatment of the devices in nitrogen atmosphere. The trap states in the methanofullerenes PC61BM, bisPC61BM and PC71BM were investigated by TSC measurements. PC61BM yielded a broad quasi-continuous trap distribution with the maximum of the distribution at about 75 meV. The comparison of the TSC spectra of the three methanofullerenes exhibited significant differences in the trap states with higher activation energies of the most prominent traps in bisPC61BM and PC71BM compared to PC61BM. This probably originates from the different isomers bisPC61BM and PC71BM consist of. Each of the isomers yields different LUMO energies, where the lower ones can act as traps. The lower limit of the trap density of all of the three investigated fullerene derivatives exhibited values in the order of 10^22 m^−3, with the highest for bisPC61BM and the lowest for PC61BM. By applying fractional TSC measurements on P3HT:PC61BM solar cells, it was shown that the trap distribution in the blend is a superposition of the traps in pure P3HT and PC61BM and additional deeper traps in the range of about 250 meV to 400 meV. The origin of these additional traps, which can not be related to the pure materials, was attributed to a higher disorder in the blend and P3HT/PC61BM interfaces. This conclusion was supported by standard TSC and Q-DLTS measurements performed on pristine and annealed P3HT:PC61BM blends, exhibiting a higher ratio of the deep traps in the pristine samples. The lower limit of the trap density of the investigated annealed solar cells was in the range of (6−8)×10^22 m^−3, which was considerably higher than in the pure materials. The influence of oxygen on P3HT:PC61BM solar cells was investigated by exposure of the devices to synthetic air under specific conditions. Exposure of the solar cells to oxygen in the dark resulted in a strong decrease in the power conversion efficiency of 60 % within 120 h, which was only caused by a loss in short-circuit current. Simultaneous illumination of the solar cells during oxygen exposure strongly accelerated the degradation, resulting in an efficiency loss of 30 % within only 3 h. Thereby, short-circuit current, open-circuit voltage and fill factor all decreased in the same manner. TSC measurements revealed an increase of the density of deeper traps for both degradation conditions, which resulted in a decrease of the mobility, as investigated by CELIV measurements. However, these effects were less pronounced than in pure P3HT. Furthermore, an increase of the equilibrium charge carrier density with degradation time was observed, which was attributed to oxygen doping of P3HT. With the aid of macroscopic simulations, it was shown that the doping of the solar cells is the origin of the loss in short-circuit current for both degradation conditions.
Um die Natur der Transportdynamik von Ladungsträgern auch auf mikroskopischen Längenskalen nicht-invasiv untersuchen zu können, wurde im ersten Schwerpunkt dieser Arbeit das PL- (Photolumineszenz-) Quenching (engl.: to quench: löschen; hier: strahlungslose Rekombination von Exzitonen) in einer organischen Dünnschicht durch die injizierten und akkumulierten Löcher in einer Transistorgeometrie analysiert. Diese Zusammenführung zweier Methoden - der elektrischen Charakterisierung von Dünnschichttransistoren und der Photolumineszenzspektroskopie - erfasst die Änderung des strahlenden Zerfalls von Exzitonen infolge der Wechselwirkung mit Ladungsträgern. Dadurch werden räumlich aufgelöste Informationen über die Ladungsverteilung und deren Spannungsabhängigkeit im Transistorkanal zugänglich. Durch den Vergleich mit den makroskopischen elektrischen Kenngrößen wie der Schwell- oder der Turn-On-Spannung kann die Funktionsweise der Transistoren damit detaillierter beschrieben werden, als es die Kenngrößen alleine ermöglichen. Außerdem wird die Quantifizierung dieser mikroskopischen Interaktionen möglich, welche beispielsweise als Verlustkanal in organischen Photovoltaikzellen und organicshen Leuchtdioden auftreten können. Die Abgrenzung zu anderen dissipativen Prozessen, wie beispielsweise der Exziton-Exziton Annihilation, Ladungsträgerrekombination, Triplett-Übergänge oder Rekombination an Störstellen oder metallischen Grenzflächen, erlaubt die detaillierte Analyse der Wechselwirkung von optisch angeregten Zuständen mit Elektronen und Löchern.
Im zweiten Schwerpunkt dieser Arbeit werden die Transporteigenschaften des Naphthalindiimids Cl2-NDI betrachtet, bei dem der molekulare Überlapp sowie die Reorganisationsenergie in derselben Größenordnung von etwa 0,1 eV liegen. Um experimentell auf den mikroskopischen Transport zu schließen, werden nach der Optimierung des Kristallwachstums Einkristalltransistoren hergestellt, mit Hilfe derer die Beweglichkeit entlang verschiedener kristallographischer Richtungen als Funktion der Temperatur gemessen werden kann. Die einkristalline Natur der Proben und die spezielle Transistorgeometrie ermöglichen die Analyse der räumlichen Anisotropie des Stromflusses. Der gemessene Beweglichkeitstensor wird daraufhin mit simulierten Tensoren auf der Basis von Levich-Jortner Raten verglichen, um auf den zentralen Ladungstransfermechanismus zu schließen.
Continuously increasing energy prices have considerably influenced the cost of living over the last decades. At the same time increasingly extreme weather conditions, drought-filled summers as well as autumns and winters with heavier rainfall and worsening storms have been reported. These are possibly the harbingers of the expected approaching global climate change. Considering the depletability of fossil energy sources and a rising distrust in nuclear power, investigations into new and innovative renewable energy sources are necessary to prepare for the coming future.
In addition to wind, hydro and biomass technologies, electricity generated by the direct conversion of incident sunlight is one of the most promising approaches. Since the syntheses and detailed studies of organic semiconducting polymers and fullerenes were intensified, a new kind of solar cell fabrication became conceivable. In addition to classical vacuum deposition techniques, organic cells were now also able to be processed from a solution, even on flexible substrates like plastic, fabric or paper.
An organic solar cell represents a complex electrical device influenced for instance by light interference for charge carrier generation. Also charge carrier recombination and transport mechanisms are important to its performance. In accordance to Coulomb interaction, this results in a specific distribution of the charge carriers and the electric field, which finally yield the measured current-voltage characteristics. Changes of certain parameters result in a complex response in the investigated device due to interactions between the physical processes. Consequently, it is necessary to find a way to generally predict the response of such a device to temperature changes for example.
In this work, a numerical, one-dimensional simulation has been developed based on the drift-diffusion equations for electrons, holes and excitons. The generation and recombination rates of the single species are defined according to a detailed balance approach. The Coulomb interaction between the single charge carriers is considered through the Poisson equation. An analytically non-solvable differential equation system is consequently set-up. With numerical approaches, valid solutions describing the macroscopic processes in organic solar cells can be found. An additional optical simulation is used to determine the spatially resolved charge carrier generation rates due to interference.
Concepts regarding organic semiconductors and solar cells are introduced in the first part of this work. All chapters are based on previous ones and logically outline the basic physics, device architectures, models of charge carrier generation and recombination as well as the mathematic and numerical approaches to obtain valid simulation results.
In the second part, the simulation is used to elaborate issues of current interest in organic solar cell research. This includes a basic understanding of how the open circuit voltage is generated and which processes limit its value. S-shaped current-voltage characteristics are explained assigning finite surface recombination velocities at metal electrodes piling-up local space charges. The power conversion efficiency is identified as a trade-off between charge carrier accumulation and charge extraction. This leads to an optimum of the power conversion efficiency at moderate to high charge carrier mobilities. Differences between recombination rates determined by different interpretations of identical experimental results are assigned to a spatially inhomogeneous recombination, relevant for almost all low mobility semiconductor devices.
The present thesis is concerned with the impact of alkali metal-doping on the electronic structure of semiconducting organic thin films. The organic molecular systems which have been studied are the polycyclic aromatic hydrocarbons picene, pentacene, and coronene. Motivated by reports about exceptional behavior like superconductivity and electronic correlations of their alkali metal-doped compounds, high quality films fabricated from the above named molecules have been studied. The electronic structure of the pristine materials and their doped compounds has been investigated using photoelectron spectroscopy. Core level and valence band studies of undoped films yield excellent photoemission spectra agreeing with or even outperforming previously reported data from the literature. Alkali metal-doping manifests itself in a uniform manner in the electronic structure for all probed samples: Opposed to reports from the literature about metallicity and even superconductivity in alkali metal-doped picene, pentacene, and coronene, all films exhibit insulating nature with an energy gap of the order of one electron-volt. Remarkably, this is independent of the doping concentration and the type of dopant, i.e., potassium, cesium, or sodium. Based on the interplay between narrow bandwidths in organic semiconductors and sufficiently high on-molecule Coulomb repulsion, the non-metallicity is attributed to the strong influence of electronic correlations leading to the formation of a Mott insulator. In the case of picene, this is consolidated by calculations using a combination of density functional theory and dynamical mean-field theory. Beyond the extensive considerations regarding electronic correlations, further intriguing aspects have been observed. The deposition of thin picene films leads to the formation of a non-equilibrium situation between substrate and film surface. Here, the establishment of a homogeneous chemical potential is hampered due to the only weak van der Waals-interactions between the molecular layers in the films. Consequently, spectral weight is measurable above the reference chemical potential in photoemission. Furthermore, it has been found that the acceptance of additional electrons in pentacene is limited. While picene and coronene are able to host up to three extra electrons, in pentacene the limit is already reached for one electron. Finally, further extrinsic effects, coming along with alkali metal-doping, have been scrutinized. The oxidation of potassium atoms induced by the reaction with molecular oxygen in the residual gas of the ultra-high vacuum system turned out to significantly influence the electronic structure of alkali metal-doped picene and coronene. Moreover, also the applied X-ray and UV irradiation caused a certain impact on the photoemission spectra. Surprisingly, both effects did not play a role in the studies of potassium-doped pentacene.
The present work addressed the influence of spins on fundamental processes in organic
semiconductors. In most cases, the role of spins in the conversion of sun light
into electricity was of particular interest. However, also the reversed process, an electric
current creating luminescence, was investigated by means of spin sensitive measurements.
In this work, many material systems were probed with a variety of innovative
detection techniques based on electron paramagnetic resonance spectroscopy.
More precisely, the observable could be customized which resulted in the experimental
techniques photoluminescence detected magnetic resonance (PLDMR), electrically
detected magnetic resonance (EDMR), and electroluminescence detected magnetic
resonance (ELDMR). Besides the commonly used continuous wave EPR spectroscopy,
this selection of measurement methods yielded an access to almost all intermediate
steps occurring in organic semiconductors during the conversion of light into electricity
and vice versa. Special attention was paid to the fact that all results were applicable
to realistic working conditions of the investigated devices, i.e. room temperature application and realistic illumination conditions.
In the course of this dissertation, we have presented the interest of using spectroscopic methods to unravel the physics of polymer semiconductors in photovoltaic applications. Applying photoluminescence and photoinduced absorption spectroscopy to the reference system P3HT:PCBM has enabled us to study the major steps of photocurrent generation in organic bulk heterojunctions, from excitons generation to charges extraction and loss mechanisms and thus to improve the understanding of those mechanisms.
The exciton binding energy, is the first obstacle to overcome for photocurrent generation in organic solar cell and the reason for the use of two materials, whose heterojunction act as a driving force for charge separation. We developed an original photoluminescence-detected field-induced exciton quenching method to investigate this energy. Absorption and photoluminescence spectra of pure P3HT show that, while both amorphous and crystalline domains participate in
absorption, the energy is then transferred to the crystalline domains, from where the photoluminescence is exclusively originating. The field dependence of this photoluminescence showed that an energy of no less than 420 meV is necessary to split excitons into non photon-emitting species. Comparing those results with energy levels obtained by absorption and photoelectron spectroscopies, confirmed that the formation of those species is only a first step toward dissociation into free charges. Indeed, photoemission spectroscopy and the onset
of photocurrent upon increasing the photon energy in a pure P3HT solar cell, concomitantly show that the energy level of a pair of free polarons is located 0.7 eV above the one of the exciton. The comprehensive analysis of those results originating from those different method enable us to draw a global picture of the states and energies involved in free polarons generation in pure material. This work has been widely acknowledged by the scientific community, published in Physical Review B in 2010 [1] and presented in national [2] and international [3] conferences.
The spectroscopy of excited states is used to detect the presence of wanted species (charges) and potentially unwanted neutral species upon photoexcitation. As such, it offers us the possibility to qualify the efficiency of charge generation and, if any, identify the competing processes and the generation of unwanted species. In the frame of the European Marie Curie Research Network SolarNType,[4] this possibility was used - in combination with morphological,
charge transport and devices characterizationsn - to study a number of new donor:acceptor blends. Thanks to those techniques, we were able to not only quantify the potential of those blends, but also to provide the chemist laboratories with a precious and detailed feedback on the strengths and weakness of the molecules, regarding charge generation, transport and extraction. The detailed study of terrylene-3,4:11,12-bis(dicarboximide) as electron acceptor for
solar cells application was published in the peer review journal Synthetic Metals and was chosen to illustrate the cover page of the issue [5].
Finally, in the last chapter, we have used time resolved photoinduced absorption to improve the understanding of the charge carrier loss mechanisms in P3HT:PCBM active layers. This comprehension is of prime importance because, the fact that this recombination is far weaker than expected from the Langevin theory, enable polarons to travel further without recombining and thus to build thicker and more efficient devices. A comprehensive analysis of steady-state
PIA spectra of pure P3HT, indicates that probing at 980 nm at a temperature between 140 and 250 K enables to monitor specifically polaron densities in both neat P3HT and P3HT:PCBM. Applying this finding to transient absorption enabled us to monitor, for the first time, the bimolecular recombination in pure P3HT, and to discover that - in sharp contrast with the blend - this recombination was in agreement with the Langevin theory. Moreover, it enables us to pinpoint the important role played by the existence of two materials and of energetical traps in the slow recombination and high recombination orders observed in the blend. This work has been published in the Journal of Applied Physics.[6]
Those new insights in the photophysics of polymer:fullerene photoactive layers could have a strong impact on the future developement of those materials. Consistent measurements of the binding energy of excitons and intermediate species, would enable to clarify the role played by excess thermal energy in interfacial states dissociation. Better understanding of blends
morphology and its influence on solar cells parameters and in particular on recombination could enable to reproduce the conditions of limited recombination on material systems offering some promising performances but with only limited active layer thicknesses. However, due to the number of parameters involved, further experimentation is required, before we can reach a quantitative modeling of bimolecular recombination.
[1] Deibel et al., Phys. Rev. B, 81:085202, 2010
[2] Gorenflot et al., Deutsche Physikalische Gesellschaft Frühjahrstagung 2010, CPP20:10, Regensburg, Germany, 2010
[3] Gorenflot et al., International Conference of Synthetic Metals, 7Ax:05, Kyoto, Japan, 2010
[4] Marie-Curie RTN "SolarNTyp" Contract No. MRTN-CT-2006-035533
[5] Gorenflot et al., Synth. Met., 161(23{24):2669-2676, 2012
[6] Gorenflot et al., J. Appl. Phys., 115(14):144502, 2014
In this work, three different material systems comprising carbon were researched: (i) Organic polymers and small molecules, in conjunction with fullerene molecules for applications in organic photovoltaics (OPV), (ii) single walled semiconducting carbon nanotubes and (iii) silicon carbide (SiC), whose defect color centers are recently in the limelight as candidates for quantum applications. All systems were analyzed using the optically detected magnetic resonance (ODMR) spectroscopy.
In the OPV chapter, first the intrinsic parameters and orientations of high spin excitons were analyzed in the materials P3HT, PTB7 and DIP. Specifically the influence of ordering in these organic systems was adressed. The second part of the OPV chapter is concerned with triplet generation by electron back transfer in the high-efficiency OPV material combination PTB7:PC71BM.
The carbon nanotube chapter first shows the way to the first unambiguous proof of the existence of triplet excitons in semiconducting (6,5) single-walled carbon nanotubes (SWNT) by ODMR spectroscopy. A model for exciton kinetics, and also orientation and intrinsic parameters were propoesed.
The last part of this work is devoted to spin centers in silicon carbide (SiC). After a brief introduction, the spin multiplicity of the V2 and V3 silicon vacancies, and also of a Frenkel pair and an unassigned defect UD in 6H SiC, and of the V2 vacancy and the Frenkel pair in 4H SiC, was shown to be S=3/2. The spin polarized pumping of the 3/2 manifold of the quartet ground state of the silicon vacancies allows stimulated microwave emission. Furthermore, in 6H SiC, the UD and Frenkel pair were shown to have a large dependence of their intrinsic zero field interaction parameters on the temperature, while the vacancies are temperature independent. The application of the UD and Frenkel pair as temperature sensor, and of the vacancies as a vector magnetic field sensor is discussed.
In summary, it can be stated that the herein studied set of acceptor-substituted squaraine dyes can be seen as potent candidates for OTFTs. Furthermore, their transistor performance can be easily tuned to obtain hole mobilities up to 0.45 cm2/Vs from solution and 1.3 cm2/Vs from sublimation by choosing adequate deposition techniques. In the end, a probable structural model derived from studies of the thin-film morphology by methods such as optical spectroscopy, AFM and X-ray even facilitated the clarification of the observed charge transport behavior.