Refine
Has Fulltext
- yes (2)
Is part of the Bibliography
- yes (2)
Year of publication
- 2014 (2) (remove)
Document Type
- Doctoral Thesis (2)
Keywords
- electrochemistry (2) (remove)
Im Rahmen der vorliegenden Arbeit wurde durch einzelmolekülspektroskopischer bzw. -mikroskopischer Methoden in Kombination mit einer mikrofluischen Zel- le unter Potenzialkontrolle die Elektrochemie von einzelnen einwandigen (6,5)- Kohlenstoffnanoröhren untersucht. Hierfür wurde ein Nahinfrarot-Photolumineszenz- Mikroskop aufgebaut und eine speziell an die experimentellen Vorgaben angepasste elektrochemische Zelle entwickelt, insofern als drei Elektroden (Arbeits-, Gegen- und Referenzelektrode) in einen mikrofluidischen Chip integriert wurden. Darüber hinaus war für die Durchführung der Experimente unter Wasser- und Sauerstoffaus- schluss die Konstruktion eines Handschuhkastens notwendig, sowie eine allgemeine Vorbehandlung der Elektrolytlösungen zur Entfernung gelöster Gase und Wasserreste.
Ein weiteres Projekt umfasste den Aufbau einer chemischen Gasphasenabschei- dungsapparatur zur Synthese von Kohlenstoffnanoröhren. Die hierbei durchgeführten Experimente erbrachten Klarheit über den Einfluss der Prozessparameter Druck, Temperatur und Durchflussrate an Edukten.
Aus den PL-Intensitätsänderungen bei Potenzialvariation konnten Reduktions- und Oxidationspotenziale (ERed = 0.15 V; EOx = 1.34 V) einzelner (6,5)-SWNTs gegen- über einer Platin Referenzelektrode und einem daraus resultierenden Redoxpotenzial
von ∆ERedOx = 1.19 V ermittelt werden. Durch diese einzelmolekülspektroskopische
Methode konnte zum einen gewährleistet werden, dass nur dieser spezielle Chira- litätstyp untersucht wurde und zum anderen eine Verfälschung der Resultate durch einen Potenzialabfall wie er typischerweise in CNT-Filmen auftritt aussgeschlossen werden. Eine Kombination der PL-Daten mit der Ramanintensitätsabhängigkeit des (6,5)-SWNT-S2-Übergangs bei Potenzialvariation erlaubte eine genauere Analyse des Löschmechanismus der PL von Kohlenstoffnanoröhren. Mithilfe eines von Her- tel et al. entwickelten diffusionslimitierten Stoßdesaktivierungsmodells konnte eine invers-quadratische Proportionalität zwischen der (6,5)-SWNT-Emission und den spannungsinduzierten Ladungsträgern ausgemacht werden. Auf Grundlage dieses Ergebnisses folgt, dass die über Photolumineszenzänderungen ermittelten Reduktions-und Oxidationswerte nicht mit den Bandkanten der CNTs übereinstimmen müssen, und dass für deren Bestimmung vielmehr auf Raman- bzw. Absorptionsspektroskopi- sche Techniken zurückgegriffen werden muss.
Die einzelmolekülspektroskopische Herangehensweise ermöglichte ferner eine statis- tische Analyse der Verteilung der Reduktions- und Oxidationspotenziale im Vergleich zu den jeweiligen Erwartungswerten. Hierdurch konnte eine Einteilung der Modifika- tionseinflüsse auf das SWNT-Redoxverhalten in zwei Grenzfälle erfolgen. Es wurde angenommen, dass diese als “Dispergiermitteleffekte” und “CNT-Strukturdefekte” be- zeichneten Auswirkungen entweder das Resultat einer heterodispersen Verteilung an DOC auf der CNT-Oberfläche oder eine Folge von Defekten in der CNT-Gitterstruktur waren. In diesem Zusammenhang ergab sich aus der interpartikulären Analyse der Reduktions- und Oxidationswerte eine Korrelation, die einem dominierenden Einfluss der “CNT-Strukturdefekte” zugeordnet werden konnte. Dieser Beobachtung entgegen- gesetzt konnten aber auch über Untersuchungen der Redoxpotenziale innerhalb einer (6,5)-SWNT lokale Bereiche ausgemacht werden, die eine signifikante Abhängigkeit von “Dispergiermitteleffekte” aufwiesen.
Abgesehen von diesen Einflüssen auf den Emissionsverlauf wurde auch eine Be- trachtung der Breite des spannungsgesteuerten Emissionsabfall durchgeführt. Da- raus konnte ermittelt werden, dass diese Ausdehnung eine Konsequenz aus der PL- Löschungseffizienz der Ladungsträger ist und, dass bei einer Verteilung von 0.32 Löschzentren pro Nanometer eine vollständige Abnahme der Photolumineszenzinten- sität induziert wird.
Darüber hinaus wurde im Rahmen dieser Arbeit das redoxchemische Verhalten in- dividueller (6,5)-SWNTs in Wechselwirkung mit Ferrocenmolekülen untersucht. Die erhaltenen Ergebnisse ließen annehmen, dass die sich ausbildende Verbindung nicht-kovalenter Natur ist. Zwei verschiedene Gründe führten zu dieser Erkennt- nis: einerseits ließen sich die Ferrocenmoleküle von der CNT-Oberfläche durch ein Durchspülen des mikrofluidischen Kanals mit einer reinen DMF-Lösung entfernen und andererseits war keine dauerhafte Emissionsminderung durch die Ausbildung kovalenter Bindungen zu beobachten. Aus der potenzialabhängigen PL wurde zudem ein Elektronentransfer der Ferrocenmoleküle in die optisch generierten Löcher des CNT-Valenzbandes festgestellt und über eine anregungsintensitätsabhängige Messung die Zunahme dieses Ladungstransfers bei steigendem Photonenfluss nachgewiesen.
Hinsichtlich der Anwendung von Kohlenstoffnanoröhren zur Elektrolyse bzw. Photo- lyse von Wasser wurde auch die Redoxchemie von (6,5)-SWNTs in diesem Solvens untersucht. Bezüglich der Emissionsintensität konnte gezeigt werden, dass diese im Vergleich zu organischen Lösungsmitteln reduziert vorliegt. Außerdem wurde eine irreversible Reaktion nach anodischer Polarisation über eine dauerhafte Löschung der PL beobachtet. Die Bestimmung der hierfür notwendigen Reaktionsumstände erbrachte, dass Wasser, Exzitonen (erzeugt durch optische Anregung) und spannungs- induzierte Löcher im Valenzband zur Bildung einer [SWNT(Q)]-Spezies führen, welche die irreversible Minderung der CNT-Emission verursacht. Darüber hinaus konnte die Reaktionsgeschwindigkeit über eine Kinetik pseudo-nullter-Ordnung be- schrieben werden, unter der Voraussetzung, dass die soeben genannten Parameter konstant verblieben. Desweiteren zeigte sich in einer ferrocenhaltigen Lösung, dass der Löscheffekt der [SWNT(Q)]-Spezies im anodischen Potenzialbereich teilweise reduziert wird. Es wurde angenommen, dass diese Beobachtung auf eine Oxidation der Löschzentren durch die Fc+-Kationen gründet.
Mit Hilfe der CVD-Apparatur gelang es Kohlenstoffnanoröhren zu synthetisieren, wobei Ethanol als Kohlenstoffquelle und ein Eisen-Kobalt-Zeolith-Gemenge als Ka- talysator diente. Die Analyse der verschiedenen Prozessparameter zeigte, dass bei T = 750 °C das beste Verteilungsverhältnis zwischen den gewünschten (6,5)-SWNTs und anderen CNT-Chiralitäten bzw. dem amorphen Kohlenstoff vorliegt. Hierfür war, dass bei T < 750 °C die Verbrennung unerwünschter amorpher Kohlenstoffreste nur geringfügig stattfindet, und dass bei T > 750 °C die Bildung anderer Chiralitäten mit größerem Durchmesser als die (6,5)-SWNT bevorzugt wurde. Die Variation der Durchflussrate hingegen wirkte sich nur in einer absoluten Zunahme aller Chirali- täten aus. Die Steigerung des (6,5)-SWNT-Anteils für höhere Durchflüsse gelang trotzdem durch die geschickte Auswahl geeigneter Druck- und Temperaturwerte. Die Experimente zur Untersuchung der Druckabhängigkeit wiesen auf eine Relation mit dem Gesetz von Le Chatelier hin, insofern als bei einer Druckverringerung eine Verschiebung der Ethanol-Crackreaktion auf Produktseite stattfand. In diesem Zusam- menhang wurde angenommen, dass die damit verstärkt gebildeten Moleküle Ethan, Ethen und Methan den CNT-Anteil zwar erhöhen, jedoch auch eine Steigerung der amorphen Kohlenstoffkonzentration verursachen. Dementsprechend ergab ein Druck von p = 9 mbar das beste (6,5)-SWNT zu dem amorphen Kohlenstoffverhältnis.
Anhand der Arbeiten in dieser Dissertation sind neue Erkenntnisse zwischen der PL-Sensitivität von (6,5)-SWNTs und deren Ladungszustand erhalten worden. Insbe- sondere die genaue Bestimmung der Korrelation zwischen der Photolumineszenz und den induzierten Ladungsträgern ermöglicht einen gezielteren Einsatz von Kohlenstoff- nanoröhren – so zum Beispiel im Bereich der Sensorik. In diesem Zusammenhang zeigen auch die interpartikulären Analysen der Redoxpotenzialverteilung die genau- en Auswirkungen vom Lösungsmittel und der Defektdichte auf die elektronische Struktur der CNTs auf. Darüber hinaus kann aus der Ursachenbestimmung für die Varianz der literaturbekannten Reduktions- bzw. Oxidationspotenziale fortan die ge- eignete spektroskopische Methode zur Evaluierung der Position von Leitungs- und Valenzband in Kohlenstoffnanoröhren besser eingegrenzt werden. Die spektroelektro- chemischen Analysen von (6,5)-SWNTs im Lösungsmittel Wasser und speziell die Bestimmung der Kinetik für die auftretende Reaktion liefern einen tieferen Einblick in die Wechselwirkung (6,5)-SWNT-H2O. Diese Ergebnisse sind insbesondere bei der Verwendung von Kohlenstoffnanoröhren als Elektrodenmaterial für die photolytische bzw. elektrolytische Spaltung von Wasser in Wasserstoff und Sauerstoff von Bedeu- tung. Neben der Untersuchung der SWNT-Wasser Interaktion unter andoischer und optischer Anregung, die zu einer kovalenten Bindung führte, wurde mit Hilfe der (6,5)- SWNT-Ferrocen Wechselwirkung ein Beispiel für eine nichtkovalente Redoxreaktion dargestellt, womit ein Vergleich dieser beiden Spezies und ihrer unterschiedlichen Auswirkungen auf die elektronische Struktur aufgezeigt werden konnte.
Within this study, the influence of the energetics of the bridge unit on electron transfer (ET) in an electrode-bridge-donor system was investigated in a monolayer environment.
This was realized by specifically designing molecules containing ferrocene carboxylic ester donors and hydroquinone derivatives as bridge units and by using a gold electrode as acceptor. The energetics of the hydroquinone derivatives was adjusted by synthetically varying its substituents with the intention of changing the ET speed and mechanisms. Thereby the choice of the substituents was based on the literature known half-wave potentials of similar solvated hydroquinone derivatives and successively confirming them by conducting cyclic voltammetry on the actual bridge units synthesized. Then, a synthetic pathway, which accommodated the limited stability of the integrated terminal ferrocene carbon acid ester, was developed and successfully employed. This was followed by developing a procedure for preparing very dense and highly ordered monolayers from the target molecules on self-made gold microelectrodes. For the electrochemical investigations, several electrolyte solutions were tested until one, which ensured low susceptibility of the characterization setup towards slight changes of the electrode arrangement and measurement parameters while ensuring sufficient stability of the monolayers, was found. Furthermore, a new, commercially available potentiostat was established for the impedance measurements, which reduced the stress on the monolayers during the electrochemical characterizations in comparison to the equipment used in many former studies. Regarding the determination of the ET rates, the data analysis protocol for the impedance measurements developed by Creager et al. was slightly adapted to allow analysis of the investigated monolayers despite their non-ideal behavior. In addition, the influence of changes to the electrical parameters of the impedance scans was investigated to minimize the error in the acquired data.
The electrochemical analysis of the monolayers by conducting cyclic voltammetry on MA, MB and MC prepared from A, B and C confirmed the accomplishment of near ideal surface coverage and exceptionally high order. The surface coverages of MB and MC were, probably due to the space filled by the substituents on their bridge units, slightly lower than those of MA. Furthermore, the shape of the redox waves of the ferrocene carboxylic acid redox center in the voltammogram of MA showed a broadening and a shift towards higher potentials, which was assigned to electrostatic interference of oxidized terminal redox centers due to the especially dense packing. However, in the voltammogram of MB, no sharp redox waves of the bridge units, as predicted by the analysis of preliminary monolayers of the same type with low surface coverage, were present. This was attributed to the different and varying microenvironment of the bridge units deeply embedded within high-density monolayers. In detail, the different degree of shielding of each individual bridge unit from counter ions and solvent molecules probably resulted in the half wave potential being shifted to varying higher potentials, thus preventing the formation of sharp redox waves. In addition, electrostatic effects of oxidized bridge units could have enhanced this effect. This leads to the conclusion that the half-wave potentials of fully solvated bridge units determined by the cyclic voltammetry are not suited to predict the energetics of the oxidized bridge states embedded within the prepared high density monolayers.
Finally, the monolayers were successfully analyzed by impedance spectroscopy, which showed that the ET rate of MA is slightly higher than that of MB, and both are higher than that of MC. All of the values were, according to literature, in the expected region considering the length and degree of conjugation of the backbone. However, this picture is relativized when considering the targeted energetic alignment of the bridge units. According to the predicted very small energy gap between the oxidized states of the donor and the bridge unit in MB, a domination of the hopping mechanism should have led to a several orders of magnitude higher ET rate than in MA and MC. That this was not the case was attributed to the underestimation of the energy of the oxidized bridge states by utilizing cyclic voltammetry of the fully solvated bridge units (see above). According to the small differences of the ET rates the superexchange process was assumed to be the dominating mechanism not only in MA and MC but also in MB. However, even when shifted, the predicted energetic order of the oxidized bridge states should have led to a moderately decreasing ET rate from MB over MA to MC. The reason for the actual ET rate in MA being slightly higher than in MB might be found in the electrostatic interference of the terminal redox centers in MA (see above).
In conclusion, the targeted model systems were prepared and the ET rates were successfully determined. However, the problems concerning the relative energetic positioning of the involved states within the dense monolayers prevented the specific alteration of the speed and mechanism of the ET. The reason for this can be probably found in the high density and order of the monolayers prepared within this work, which hamper the intrusion of the components of the electrolyte solutions. This various degree of stabilization for the individual bridge units by counter ions and solvent molecules leads to the energy of the oxidized bridge states being splitted and shifted towards higher potentials with respect to fully solvated bridge units. This effect might be further enhanced by electrostatics of neighboring already oxidized bridge states. All this makes the predetermination of the energetics of the embedded bridge units extremely difficult. On one hand, this behavior can be considered an obstacle and could probably be circumvented by designing molecules with bulky anchor groups and rigid molecular backbones, which would ensure perpendicular arrangement to the surface and full exposure of the bridge and terminal redox centers to the solvent molecules and counter ions. On the other hand, monolayers which completely embed integral redox centers might open up the opportunity to study the effects of microenvironments similar to those in solid state materials.
Regarding mixed valence compounds, the present study focuses on bistriarylamine radical cation F∙+, which contains the [3.3]paracyclophane bridge unit. The results were compared to the, except for the bridge units, identical literature known compounds G∙+ and N∙+ with [2.2]paracyclophane and p-xylene bridges respectively. This led to the conclusion that slightly different bridge units can induce substantial changes to the internal reorganization energy. This is especially noteworthy since it is usually believed that structural adaption limited to the redox centers taking part in the charge transfer dominates the internal reorganization energy. Furthermore, the application of the two-state Mulliken-Hush approach shows that compounds F∙+ and G∙+ have near identical couplings and similar thermal barriers. Confirmation of the latter finding as well as near identical thermal electron transfer rates for both compounds were provided via a cooperation project by Grampp et al. in which these values were directly extracted from temperature dependent electron paramagnetic resonance measurements. These results are quite unexpected since the “through-space” distances of the stacked pi-systems in the paracyclophane bridges differ significantly. They are well within the sum of the van der Waals radii in G∙+ and barely within them in compound F∙+. In addition, these findings weaken the common assumption of the ethylene bridges in G∙+ substantially adding to the electronic coupling, since then, in F∙+, due to its propylene linkers, the coupling should be substantially reduced. Finally, relying on the fact that the electronic couplings are only three times higher and the thermal electron transfer rates are only one order of magnitude higher for N∙+ than for compounds F∙+ and G∙+ shows that intermolecular electron transfer in solid state materials can remain efficient, if the interacting pi-systems stay within the sum of van der Waals radii of their carbons.
Concerning the donor-acceptor dyads, the current investigation centers on triarylamine-cyclophane-naphtalene diimide (TAA-CP-NDI) compounds which display almost complete photoinduced charge separation. Furthermore, their singlet charge separated states show lifetimes of hundreds of nanoseconds, which is rarely found in such simple dyads. In the present case they can be attributed to the particular amount of electronic coupling V (on the order of 100 cm^–1), which is brought about by incorporation of the smallest model systems for pi-stacks, the CPs, together with the nodes on the NDI lowest unoccupied molecular orbital, which electronically decouples the central NDI from its nitrogen substituents. In agreement with studies of [2.2]- and [3.3]paracyclophane bridged mixed valence compounds (see above), the cycolphane bridged dyads show very similar electronic coupling when dealing with ground state processes like charge recombination. However, when investigating excited state processes, like charge separation in the TAA-CP-NDI dyads, one has to bear in mind that the CP orbitals are involved in the formation of intermediate states that likely possess charge transfer character. In this case, the [2.2]paracyclophane bridge obviously induces a stronger coupling than the [3.3]paracyclophane. Another interesting property of the dyads studied here is the substantial population of the triplet charge separated (CS) state of ca. one third regarding both CS states, which is brought about by singlet-triplet interconversion from the singlet CS state. Thus, the triplet CS state with a lifetime of several microseconds acts as a kind of buffer for the CS state before recombining to the ground state and, thus, leads to distinctly prolonged overall lifetimes of the charge separated states. Thus it can be concluded that the intersystem crossing and charge recombination (CR) processes of the CS states are governed by a delicate balance of a large electronic coupling V and a large exchange interaction 2J (both with regard to systems containing a through-space pathway). The latter appears to be induced by second order interaction with a local triplet state lying close in energy to the CS state. This balance results in slow CR- and singlet-triplet- interconversion rates, which differ only by one order of magnitude. Compared to the many NDI containing dyads studied so far, these features of the dyads studied here are, to the best of our knowledge, unique. Especially the combination of high quantum yield of charge separation, long lifetimes and high energy of the charge separated state make the investigated systems interesting for practical applications. Furthermore, the presented unraveling of the underlying mechanisms is of substantial value for the future design of dyads for practical applications regarding the implementation and adjustment of these favorable properties.