Refine
Has Fulltext
- yes (2)
Is part of the Bibliography
- yes (2)
Document Type
- Doctoral Thesis (2) (remove)
Keywords
- Cadmiumsulfid (2) (remove)
Institute
- Physikalisches Institut (2) (remove)
Ziel dieser Arbeit war die Stabilisierung von Cadmiumsulfid CdS mit Pluronic P123, einem Polymer.
CdS ist ein Halbleiter, der zum Beispiel in der Photonik und bei optischen Anwendungen eingesetzt wird und ist deshalb äußerst interessant, da seine Bandlücke als Nanopartikel verschiebbar ist. Für die Photovoltaik ist es ein attraktives Material, da es im sichtbaren Licht absorbiert und durch die Bandlückenverschiebung effektiver absorbieren kann. Dies ist unter dem Namen Quantum Size Effekt bekannt. Als Feststoff ist CdS für einen solchen Anwendungsbereich weniger geeignet, zumal der Effekt der Bandlückenverschiebung dort nicht auftritt. Wissenschaftler bemühen sich deshalb CdS als Nanopartikeln zu stabilisieren, weil CdS in wässrigen Lösungen ein stark aggregierendes System, also stark hydrophob ist. Es wurden zwei Kriterien für die erfolgreiche Stabilisierung von CdS festgelegt. Zum einen muss das Cds homogen im Medium verteilt sein und darf nicht agglomerieren. Zum anderen, müssen die CdS Nanopartikel kleiner als 100 A sein.
In meiner Arbeit habe ich solche Partikel hergestellt und stabilisiert, d.h. verhindert, dass die Partikel weiterwachsen und gleichzeitig ihre Bandlücke verschoben wird. Die Herausforderung liegt nicht in der Herstellung, aber in der Lösung von CdS im Trägerstoff, da CdS in den meisten Flüssigkeiten nicht löslich ist und ausfällt. Die Stabilisierung in wässrigen Lösungen wurde das erste Mal durch Herrn Prof. Dr. Rempel mit Ethylendiamintetraessigsäure EDTA erfolgreich durchgeführt. Mit EDTA können jedoch nur sehr kleine Konzentrationen stabilisiert werden. Zudem können Parameter wie Größe und Geschwindigkeit der Reaktion beim Stabilisieren der CdS-Nanopartikel nicht angepasst oder beeinflusst werden. Dieses Problem ist dem, vieler medizinischer Wirkstoffe sehr ähnlich, die in hohen Konzentrationen verabreicht werden sollen, aber nicht oder nur schwer in Wasser löslich sind (Bsp. Kurkumin). Ein vielversprechender Lösungsweg ist dort, die Wirkstoffe in große Trägerpartikel (sog. Mizellen) einzuschleusen, die ihrerseits gut löslich sind. In meiner Arbeit habe ich genau diesen Ansatz für CdS verfolgt. Als Trägerpartikel/Mizelle wurde das bekannte Copolymer Pluronic P123 verwendet. Aus dieser Pluronic Produktreihe wird P123 gewählt, da es die größte Masse bei gleichzeitig höchstem Anteil von Polypropylenoxid PPO im Vergleich zur Gesamtkettenlänge hat. P123 ist ein ternäres Polyether oder Dreiblockkopolymer und wird von BASAF industriell produziert. Es besteht aus drei Böcken, dem mittlere Block Polypropylenoxid PPO und den beiden äußeren Blöcken Polyethylenoxid PEO. Der Buchstabe P steht für pastös, die ersten beiden Ziffern in P123 mit 300 multipliziert ergeben das molare Gewicht und die letzte Ziffer mit 10 multipliziert entspricht dem prozentualen Gewichtsanteil PEO. Die Bildung von Mizellen aus den P123 Molekülen kann bewusst über geringe Temperaturänderungen gesteuert werden. Bei ungefähr Raumtemperatur liegen Mizellen vor, die sich bei höheren Temperaturen von sphärischen in wurmartige Mizellen umwandeln. Oberhalb einer Konzentration von 30 Gewichtsprozent wtp bilden die Mizellen außerdem einen Flüssigkristall. Ich habe in meiner Arbeit zunächst P123 mit Hilfe von Röntgenstreuung untersucht. Anders als andere Methoden gibt Röntgenstreuung direkten Aufschluss über die Morphologie der Stoffe. Röntgenstreuung kann die Mischung von P123 mit CdS abbilden und lässt darauf schließen, ob das Ziel erreicht werden konnte, stabile CdS Nanopartikel in P123 zu binden.
Für die Stabilisierung der Nanopartikel ist es zunächst notwendig die richtigen Temperaturen für die Ausgangslösungen und gemischten Lösungen zu finden. Dazu muss P123 viel genauer untersucht werden, als der momentane Kenntnisstand in der Literatur. Zu diesem Zweck als auch für die Analyse des stabilisierten CdS habe ich ein neues Instrument am LRM entwickelt, sowie eine temperierbare Probenumgebung für Flüssigkeiten fürs Vakuum, um morphologische Eigenschaften aus Streuamplituden und -winkeln zu entschlüsseln. Diese Röntgenstreuanlage wurde konzipiert und gebaut, um auch im Labor P123 in kleinen Konzentrationen messen zu können. Röntgenkleinwinkelstreuung eignet sich besonders als Messmethode, da die Probe mit einer hohen statistischen Relevanz in Flüssigkeit und in verschiedenen Konzentrationen analysiert werden kann.
Für die Konzentrationen 5, 10 und 30 wtp konnte das temperaturabhängige Verhalten von P123 präzise mit Röntgenkleinwinkelstreuung SAXS gemessen und dargestellt werden. Für 5 wtp konnten die Größen der Unimere und Mizellen bestimmt werden. Trotz der nicht vorhandenen Absolutkalibration für diese Konzentration konnten dank des neu eingeführten Parameters kappa eine Dehydrierung der Mizellen mit steigender Temperatur abgeschätzt, sowie eine Hysterese zwischen dem Heizen und Abkühlen festgestellt werden. Für die Konzentration von 10 wtp wurden kleinere Temperaturschritte gewählt und die Messungen zusätzlich absolut kalibriert. Es wurden die Größen und Streulängendichten SLD der Unimere und Mizellen präzise bestimmt und ein vollständiges Form-Phasendiagramm erstellt. Auch für diese Konzentration konnte eine Hysterese eindeutig an der Größe, SLD und am Parameter kappa gezeigt werden, sowie eine Dehydrierung des Mizellenkerns. Dies beweist, dass der Parameter kappa geeignet ist, um bei nicht absolut kalibrierten Messungen, Aussagen über die Hydrierung und Hysterese komplexer Kern-Hülle Modelle zu machen. Für die Konzentration von 30 wtp konnte zwischen 23°C und 35°C eine FCC Struktur nachgewiesen werden. Dabei vergrößert sich die Gitterkonstante der FCC Struktur von 260 A auf 289 A in Abhängigkeit der Temperatur.
Durch das Mischen zweier Lösungen, zum einen CdCl2 und 30 wtp P123 und zum anderen Na2S und 30 wtp P123, konnte CdS erfolgreich stabilisiert werden. Mit einer Kamera wurde die Gelbfärbung der Lösung, und somit die Bildung des CdS, in Abhängigkeit der Zeit untersucht. Es konnte festgestellt werden, dass das Bilden der CdS Nanopartikel je nach Konzentration und Temperierprogramm zwischen 30 und 300 Sekunden dauert und einer logistischen Wachstumsfunktion folgt. Höhere Konzentrationen CdS bewirken einen schnelleren Anstieg der Wachstumsfunktion. Mittels UV-Vis Spektroskopie konnte gezeigt werden, dass die Bandlücke von CdS mit steigender Konzentration konstant bei 2,52 eV bleibt. Eine solche Verschiebung der Bandlücke von ungefähr 0,05 eV im Vergleich zum Festkörper, deutet auf einen CdS Partikeldurchmesser von 80A hin. Mit SAXS konnte gezeigt werden, dass sich die flüssigkristalline Struktur des P123 bei zwei verschiedenen Konzentrationen CdS, von 0,005 und 0,1 M, nicht ändert. Das CdS wird zwischen den Mizellen, also durch die Bildung des Flüssigkristalls, und im Kern der Mizelle aufgrund seiner Hydrophobizität stabilisiert. Die Anfangs definierten Kriterien für eine erfolgreiche Stabilisierung wurden erfüllt.
P123 ist ein hervorragend geeignetes Polymer, um hydrophobes CdS, sowohl durch die Bildung eines Flüssigkristalls, als auch im Kern der Mizelle zu stabilisieren.
Very small, thioglycerol (TG)-capped CdS nanoparticles were synthesized by a wet chemical technique and investigated in the framework of this thesis. Also glutathione-capped particles were investigated for a comparison of the capping agents. High-resolution photoelectron spectroscopy using high-brilliance synchrotron radiation was applied as the major tool for the characterization of these particles. Additionally, the particles were investigated with UV-VIS absorption spectroscopy, XPS using a laboratory source, valence band photoemission spectroscopy (VBPES), near-edge x-ray absorption spectroscopy (NEXAFS), and micro-Raman spectroscopy to address various aspects of the particles. In the beginning, an overview on size quantization effects is given to create a theoretical background behind the work presented in this thesis. Furthermore, an overview of various conventional techniques for size determination is presented. Exact information about size, shape and size distribution of nanoparticles is not yet achievable because of experimental limitations of the various size determination methods. Nanoparticles, with a range of sizes from 1.1 to 4. 2 nm, were synthesized using non-aqueous preparation and a TG capping. It is demonstrated that the use of the non-aqueous wet chemical synthesis method enables the production of very small particles and prohibits the aging of the particles. Furthermore, TG capping leads to a significant improvement for a narrow size distribution. Moreover, the results are very reproducible with TG capping and non-aqueous synthesis. Monodispersed particles can be produced by a size selective precipitation method, however, the reproducibility is questionable due to the aqueous medium of the synthesis in this case. High-resolution photoemission measurements on the small particles, i.e., 1.1 nm (CdS-A), 1.4 nm (CdS-B), 1.7 nm (CdS-C), and 1.8 nm (CdS-D, glutathione-capped), revealed five components as constituents of the S 2p signal after a careful data evaluation. Furthermore, it was observed that the particles with different sizes and capping show differences in the photoemission spectra and also in the beam damage behaviour. The different components of CdS-B were assigned as S atoms with different Cd neighbors, S atoms from thiol and S atoms in a partially oxidized state, based on the observed intensity changes of these components as a function of photon energy and beam damage, and on previous photoemission work on CdS nanoparticles [23, 45]. Furthermore, it was found that this assignment cannot be directly transferred to other particles. A new approach of structural model-based photoemission intensity calculations in comparison with the experimental data is presented. This enables us to understand subtle features in the photoemission spectra, in particular the intensity changes of the different components as a function of photon energy and beam exposure. This approach is especially applied to CdS-B (as some structural information for this particle is avialable from XRD), using three different structural models. It is found that a structural model with 33 S atoms can explain the experimental intensity changes of CdS-B. Furthermore, it is found that the photoemission spectra can be used to determine the particle size indirectly, as other plausible models show significant deviation from the experimental data. To study the various aspects by calculations, such as the influence of the particle shape and of the value of the mean free path, a program developed with L. Weinhardt and O. Fuchs is used for the intensity calculations. In order to determine a reasonable value of the mean free path for the used photon energies, two different equations from previous reports (Seah et al. and Powell et al.) are applied. As average mean free path values for the two photon energies we chose 5.5 ± 2 Å (254 eV) and 14 ± 2 Å (720 eV). The program calculation confirms the result of simple “manual” calculations of the different models. Moreover, it is tested that the value of , used in the calculations does not produce any significant influence on the calculation results. Another interesting feature is derived from the calculations that a model with a rather round shape produces similar intensity ratios for the different components to those of the data. Thus this new approach of analysis of photoemission spectra offers a way to determine particle sizes and to some extent to give an impression of the approximate particle shape. Furthermore, it is observed that the electronic band gap is larger compared to the optical band gap, which was attributed to an enhanced electron-hole correlation for optical absorption in small particles. The XPS experiments performed in the laboratory using an x-ray tube, show that the thin films produced from a freshly synthesized nanoparticle solution are fairly homogeneous and non-charging. Moreover, annealing experiments indicated that TG-capped particles posses less thermal stability as compared to MPA-capped particles. It was demonstrated that beam-induced effects play a major role. However, the knowledge of the time scale for such effects gives the possibility to record photoemission spectra with fairly good signal quality and to extrapolate to zero radiation damage. Further, particles with different sizes and capping show different beam damage behaviour. The thin film preparation by electrophoresis results in significant changes in the spectrum indicating agglomeration, while the drop-deposition technique points towards spectral changes on the rim of the sample, which can be avoided by focusing the radiation to the centre of the deposited dried drop. Micro-Raman experiments carried out in collaboration with C. Dem, Dr. M. Schmitt and Prof. W. Kiefer exhibited major differences in the spectra of nanoparticles as compared to those of the capping molecule thioglycerol. For instance, the absence of the S-H vibrational modes indicates the consumption or removal of all unreacted capping molecules. There is definitely a need for further detailed investigations concerning various interesting aspects of this work. For instance, it would be of significance to extend the program calculations to more models. Also more information about the band gap opening has to be gathered in order to find out the reason for the larger electronic band gap as compared to the optical band gap. The photoemission analysis approach using a model calculation has to be extended to differently prepared nanoparticles, in particular, to address the differences in the location of the various species in the particle as a function of preparation. The efforts of XRD simulations by C. Kumpf et al. [50] may reveal significant new information about the particle size and the size distribution. It can be expected that the program calculations, if extended to more models, can prove the potential of photoelectron spectroscopy to serve as a tool for size and shape determination of nanoparticles, which is a new contribution to the investigation of nanoparticles.