Refine
Has Fulltext
- yes (2)
Is part of the Bibliography
- yes (2)
Document Type
- Journal article (1)
- Doctoral Thesis (1)
Keywords
- orthodontic brackets (2) (remove)
Institute
Ziel der Arbeit war die Bestimmung der Haftfestigkeit und des Debondingverhaltens verschiedener Bracket- und Adhäsivsysteme unter Berücksichtigung eines neu entwickelten Basisdesigns. Hierbei wurden zwei unterschiedliche Testmethoden sowie differierende Untergrundmaterialien verwendet.
Zur Prüfung des Verbundes zwischen Bracket, Adhäsiv und Untergrund wurden gemäß der DIN 13990-2 die Brackets Bio Quick (Forestadent), Micro Sprint (Forestadent), Micro Sprint mit neu entwickelter Stotzenbasis (Forestadent), Equilibrium mini (Dentaurum) und In-Ovation mini (Dentsply) im Abscher- und Abzugversuch getestet. Sie wurden mit den Adhäsiven Transbond XT, Kurasper F und GC Ortho Connect auf bovine Zähne sowie auf PMMA-Ringe geklebt und anschließend hinsichtlich ihrer Haftfestigkeit untersucht. Vergleiche konnten außerdem zwischen den Testmethoden der Abscher- und Abzugtests wie auch der Untergrundmaterialien Zahn und Ring angestellt werden. Die Menge des Restadhäsivs auf der Bracketbasis wurde anschließend mikroskopisch bestimmt und anhand des Adhesive Remnant Index (ARI) dargestellt.
Im Vergleich der Abscher- und Abzugprüfungen sowie der Untergründe Zahn und Ring konnten beim Abscheren der Brackets und der Anbringung auf Zähnen signifikant höhere Haftwerte erzielt werden. Unabhängig der Brackets ist auf den Zähnen kein signifikanter Unterschied zwischen den Adhäsiven zu erkennen, auf den Ringen hingegen erreicht GC Ortho Connect signifikant geringere Haftfestigkeiten. Die höchsten Haftfestigkeitswerte (in MPa) erreichten beim Abscheren vom Zahn und bei beiden Debondingmethoden vom Ring das Equilibrium mini in Kombination mit den Adhäsiven Kurasper auf dem Ring (Abscher 23,4 MPa/Abzug 8,1 MPa) und GC Ortho Connect auf dem Zahn (23,55 MPa). Beim Abzug vom Zahn erreichte das Micro Sprint mit Stotzenbasis in Kombination mit Transbond XT die höchste Haftfestigkeit (8,02 MPa). In der Untersuchung des ARI verblieb größtenteils mehr als 50% Restadhäsiv auf der Bracketbasis.
Objective: The objective of this study was to investigate the applicability of microanalytical methods with high spatial resolution to the characterization of the composition and corrosion behavior of two bracket systems.
Material and methods: The surfaces of six nickel-free brackets and six nickel-containing brackets were examined for signs of corrosion and qualitative surface analysis using an electron probe microanalyzer (EPMA), prior to bonding to patient's tooth surfaces and four months after clinical use. The surfaces were characterized qualitatively by secondary electron (SE) images and back scattered electron (BSE) images in both compositional and topographical mode. Qualitative and quantitative wavelength-dispersive analyses were performed for different elements, and by utilizing qualitative analysis the relative concentration of selected elements was mapped two-dimensionally. The absolute concentration of the elements was determined in specially prepared brackets by quantitative analysis using pure element standards for calibration and calculating correction-factors (ZAF).
Results: Clear differences were observed between the different bracket types. The nickel-containing stainless steel brackets consist of two separate pieces joined by a brazing alloy. Compositional analysis revealed two different alloy compositions, and reaction zones on both sides of the brazing alloy. The nickel-free bracket was a single piece with only slight variation in element concentration, but had a significantly rougher surface. After clinical use, no corrosive phenomena were detectable with the methods applied. Traces of intraoral wear at the contact areas between the bracket slot and the arch wire were verified. Conclusion: Electron probe microanalysis is a valuable tool for the characterization of element distribution and quantitative analysis for corrosion studies.