Refine
Has Fulltext
- yes (2)
Is part of the Bibliography
- yes (2)
Document Type
- Journal article (2)
Language
- English (2)
Keywords
- acupuncture (1)
- effectiveness (1)
- finite element model of the complete masticatory system (1)
- mechanical simulations of mandibular movement (1)
- occlusal design (1)
- oro‐facial pain (1)
- randomised controlled trial (1)
- simulation of chewing process and teeth grinding (1)
- temporomandibular disorders (1)
Institute
Background and Objective
The aim of this single‐centre, two‐arm, parallel‐group, double‐blinded, randomised controlled trial was to investigate the disputed specific effectiveness of acupuncture by comparing acupuncture on specific and non‐specific points among patients with non‐chronic, painful TMDs.
Methods
Following predefined eligibility criteria, 49 consecutive patients of both sexes were recruited to the study. All subjects were diagnosed with a non‐chronic (Graded Chronic Pain Scale grade <3) painful TMD, as assessed using the Diagnostic Criteria for Temporomandibular Disorders (DC/TMD). Patients were randomly assigned to group A (acupuncture on specific points) or group B (acupuncture on non‐specific points) after the initial examination (T0). Both acupuncture treatment sessions were conducted by a trained dentist once a week for four weeks. The examination was repeated five weeks (T5) after T0 by one calibrated examiner who was unaware of the study groups. Characteristic pain intensity (CPI) was evaluated as the main outcome criterion and compared between times and treatment groups by means of non‐parametric tests (significance level set at P = .05). Secondary outcomes comprised the maximum corrected active mouth‐opening without pain (MAO); patients’ expectations regarding acupuncture treatment and pain development; depressivity; and oral health‐related quality of life (OHRQoL).
Results
A total of 41 patients (38 female) successfully completed the study (mean age: 40.17 ± 16.61). The two groups did not differ significantly at any time in terms of age and CPI. However, CPI was significantly (P < .05) lower at T5 than at T0 for both groups (29.66 and 30.35% lower in group A and group B, respectively). An increase in MAO was observed at T5 for both groups but was significant for group B only (P = .016). All patients had positive expectations of acupuncture therapy, and the two groups did not differ significantly at T5 with regard to the extent to which their expectations had been fulfilled by the treatment (P = .717). Comparison of T0 and T5 showed a statistically significant reduction of depressivity for group A (P = .0205), but no significant change for group B (P = .329). At T5, OHRQoL had improved significantly for both groups (group A, P = .018; group B, P < .001) compared with at T0.
Conclusions
Acupuncture on both specific and non‐specific points reduces the non‐dysfunctional pain of TMD patients. The effect of acupuncture on painful TMD cannot be attributed to the specific point selection.
The occlusal design plays a decisive role in the fabrication of dental restorations. Dentists and dental technicians depend on mechanical simulations of mandibular movement that are as accurate as possible, in particular, to produce interference-free yet chewing-efficient dental restorations. For this, kinetic data must be available, i.e., movements and deformations under the influence of forces and stresses. In the present study, so-called functional data were collected from healthy volunteers to provide consistent information for proper kinetics. For the latter purpose, biting and chewing forces, electrical muscle activity and jaw movements were registered synchronously, and individual magnetic resonance tomograms (MRI) were prepared. The acquired data were then added to a large complex finite element model of the complete masticatory system using the functional information obtained and individual anatomical geometries so that the kinetics of the chewing process and teeth grinding could be realistically simulated. This allows developing algorithms that optimize computer-aided manufacturing of dental prostheses close to occlusion. In this way, a failure-free function of the dental prosthesis can be guaranteed and its damage during usage can be reduced or prevented even including endosseous implants.