Refine
Has Fulltext
- yes (17)
Is part of the Bibliography
- yes (17)
Document Type
- Doctoral Thesis (16)
- Bachelor Thesis (1)
Keywords
- Kleinsatellit (3)
- Distributed Control (2)
- Hardware (2)
- Kollisionsschutz (2)
- Raumfahrttechnik (2)
- Satellit (2)
- Software (2)
- 3D Reconstruction (1)
- 3D-Rekonstruktion (1)
- Ablaufplanung (1)
Institute
Sonstige beteiligte Institutionen
EU-Project number / Contract (GA) number
- 320377 (1)
Mini Unmanned Aerial Vehicles (MUAVs) are becoming popular research platform and
drawing considerable attention, particularly during the last decade due to their afford- ability and multi-dimensional applications in almost every walk of life. MUAVs have obvious advantages over manned platforms including their much lower manufacturing and operational costs, risk avoidance for human pilots, flying safely low and slow, and realization of operations that are beyond inherent human limitations. The advancement in Micro Electro-Mechanical System (MEMS) technology, Avionics and miniaturization of sensors also played a significant role in the evolution of MUAVs. These vehicles range from simple toys found at electronic supermarkets for entertainment purpose to highly sophisticated commercial platforms performing novel assignments like offshore wind power station inspection and 3D modelling of buildings etc. MUAVs are also more environment friendly as they cause less air pollution and noise. Unmanned is therefore unmatched. Recent research focuses on use of multiple inexpensive vehicles flying together, while maintaining required relative separations, to carry out the tasks efficiently compared to a single exorbitant vehicle. Redundancy also does away the risk of loss of a single whole-mission dependent vehicle. Some of the valuable applications in the domain of cooperative control include joint load transportation, search and rescue, mobile communication relays, pesticide spraying and weather monitoring etc. Though realization of multi-UAV coupled flight is complex, however obvious advantages justify
the laborious work involved...
Remote sensing time series is the collection or acquisition of remote sensing data in a
fixed equally spaced time period over a particular area or for the whole world. Near
daily high spatial resolution data is very much needed for remote sensing applications
such as agriculture monitoring, phenology change detection, environmental
monitoring and so on. Remote sensing applications can produce better and accurate
results if they are provided with dense and accurate time series of data. The current
remote sensing satellite architecture is still not capable of providing near daily
or daily high spatial resolution images to fulfill the needs of the above mentioned
remote sensing applications. Limitations in sensors, high development, operational
costs of satellites and presence of clouds blocking the area of observation are some
of the reasons that makes near daily or daily high spatial resolution optical remote
sensing data highly challenging to achieve. With developments in the optical sensor
systems and well planned remote sensing satellite constellations, this condition
can be improved but it comes at a cost. Even then the issue will not be completely
resolved and thus the growing need for high temporal and high spatial resolution
data cannot be fulfilled entirely. Because the data collection process relies on satellites
which are physical system, these can fail unpredictably due to various reasons
and cause a complete loss of observation for a given period of time making a gap
in the time series. Moreover, to observe the long term trend in phenology change
due to rapidly changing environmental conditions, the remote sensing data from
the present is not just sufficient, the data from the past is also important. A better
alternative solution for this issue can be the generation of remote sensing time series
by fusing data from multiple remote sensing satellite which has different spatial and
temporal resolutions. This approach will be effective and efficient. In this method
a high temporal low spatial resolution image from a satellite such as Sentinel-2 can
be fused with a low temporal and high spatial resolution image from a satellite such
as the Sentinel-3 to generate a synthetic high temporal high spatial resolution data.
Remote sensing time series generation by data fusion methods can be applied to
the satellite images captured currently as well as the images captured by the satellites
in the past. This will provide the much needed high temporal and high spatial
resolution images for remote sensing applications. This approach with its simplistic
nature is cost effective and provides the researchers the means to generate the
data needed for their application on their own from the limited source of data available
to them. An efficient data fusion approach in combination with a well planned
satellite constellation can offer a solution which will ensure near daily time series of
remote sensing data with out any gap. The aim of this research work is to develop
an efficient data fusion approaches to achieve dense remote sensing time series.
A complete simulation system is proposed that can be used as an educational tool by physicians in training basic skills of Minimally Invasive Vascular Interventions. In the first part, a surface model is developed to assemble arteries having a planar segmentation. It is based on Sweep Surfaces and can be extended to T- and Y-like bifurcations. A continuous force vector field is described, representing the interaction between the catheter and the surface. The computation time of the force field is almost unaffected when the resolution of the artery is increased.
The mechanical properties of arteries play an essential role in the study of the circulatory system dynamics, which has been becoming increasingly important in the treatment of cardiovascular diseases. In Virtual Reality Simulators, it is crucial to have a tissue model that responds in real time. In this work, the arteries are discretized by a two dimensional mesh and the nodes are connected by three kinds of linear springs. Three tissue layers (Intima, Media, Adventitia) are considered and, starting from the stretch-energy density, some of the elasticity tensor components are calculated. The physical model linearizes and homogenizes the material response, but it still contemplates the geometric nonlinearity. In general, if the arterial stretch varies by 1% or less, then the agreement between the linear and nonlinear models is trustworthy.
In the last part, the physical model of the wire proposed by Konings is improved. As a result, a simpler and more stable method is obtained to calculate the equilibrium configuration of the wire. In addition, a geometrical method is developed to perform relaxations. It is particularly useful when the wire is hindered in the physical method because of the boundary conditions. The physical and the geometrical methods are merged, resulting in efficient relaxations. Tests show that the shape of the virtual wire agrees with the experiment. The proposed algorithm allows real-time executions and the hardware to assemble the simulator has a low cost.
There is great interest in affordable, precise and reliable metrology underwater:
Archaeologists want to document artifacts in situ with high detail.
In marine research, biologists require the tools to monitor coral growth and geologists need recordings to model sediment transport.
Furthermore, for offshore construction projects, maintenance and inspection millimeter-accurate measurements of defects and offshore structures are essential.
While the process of digitizing individual objects and complete sites on land is well understood and standard methods, such as Structure from Motion or terrestrial laser scanning, are regularly applied, precise underwater surveying with high resolution is still a complex and difficult task.
Applying optical scanning techniques in water is challenging due to reduced visibility caused by turbidity and light absorption.
However, optical underwater scanners provide significant advantages in terms of achievable resolution and accuracy compared to acoustic systems.
This thesis proposes an underwater laser scanning system and the algorithms for creating dense and accurate 3D scans in water.
It is based on laser triangulation and the main optical components are an underwater camera and a cross-line laser projector.
The prototype is configured with a motorized yaw axis for capturing scans from a tripod.
Alternatively, it is mounted to a moving platform for mobile mapping.
The main focus lies on the refractive calibration of the underwater camera and laser projector, the image processing and 3D reconstruction.
For highest accuracy, the refraction at the individual media interfaces must be taken into account.
This is addressed by an optimization-based calibration framework using a physical-geometric camera model derived from an analytical formulation of a ray-tracing projection model.
In addition to scanning underwater structures, this work presents the 3D acquisition of semi-submerged structures and the correction of refraction effects.
As in-situ calibration in water is complex and time-consuming, the challenge of transferring an in-air scanner calibration to water without re-calibration is investigated, as well as self-calibration techniques for structured light.
The system was successfully deployed in various configurations for both static scanning and mobile mapping.
An evaluation of the calibration and 3D reconstruction using reference objects and a comparison of free-form surfaces in clear water demonstrate the high accuracy potential in the range of one millimeter to less than one centimeter, depending on the measurement distance.
Mobile underwater mapping and motion compensation based on visual-inertial odometry is demonstrated using a new optical underwater scanner based on fringe projection.
Continuous registration of individual scans allows the acquisition of 3D models from an underwater vehicle.
RGB images captured in parallel are used to create 3D point clouds of underwater scenes in full color.
3D maps are useful to the operator during the remote control of underwater vehicles and provide the building blocks to enable offshore inspection and surveying tasks.
The advancing automation of the measurement technology will allow non-experts to use it, significantly reduce acquisition time and increase accuracy, making underwater metrology more cost-effective.
Time-triggered communication is widely used throughout several industry do-
mains, primarily for reliable and real-time capable data transfers. However,
existing time-triggered technologies are designed for terrestrial usage and not
directly applicable to space applications due to the harsh environment. In-
stead, specific hardware must be developed to deal with thermal, mechanical,
and especially radiation effects.
SpaceWire, as an event-triggered communication technology, has been used
for years in a large number of space missions. Its moderate complexity, her-
itage, and transmission rates up to 400 MBits/s are one of the main ad-
vantages and often without alternatives for on-board computing systems of
spacecraft. At present, real-time data transfers are either achieved by prior-
itization inside SpaceWire routers or by applying a simplified time-triggered
approach. These solutions either imply problems if they are used inside dis-
tributed on-board computing systems or in case of networks with more than
a single router are required.
This work provides a solution for the real-time problem by developing
a novel clock synchronization approach. This approach is focused on being
compatible with distributed system structures and allows time-triggered data
transfers. A significant difference to existing technologies is the remote clock
estimation by the use of pulses. They are transferred over the network and
remove the need for latency accumulation, which allows the incorporation of
standardized SpaceWire equipment. Additionally, local clocks are controlled
decentralized and provide different correction capabilities in order to handle
oscillator induced uncertainties. All these functionalities are provided by a developed Network Controller (NC), able to isolate the attached network and
to control accesses.
This thesis deals with the first part of a larger project that follows the ultimate goal of implementing a software tool that creates a Mission Control Room in Virtual Reality. The software is to be used for the operation of spacecrafts and is specially developed for the unique real-time requirements of unmanned satellite missions. Beginning from launch, throughout the whole mission up to the recovery or disposal of the satellite, all systems need to be monitored and controlled in continuous intervals, to ensure the mission’s success. Mission Operation is an essential part of every space mission and has been undertaken for decades. Recent technological advancements in the realm of immersive technologies pave the way for innovative methods to operate spacecrafts. Virtual Reality has the capability to resolve the physical constraints set by traditional Mission Control Rooms and thereby delivers novel opportunities. The paper highlights underlying theoretical aspects of Virtual Reality, Mission Control and IP Communication. However, the focus lies upon the practical part of this thesis which revolves around the first steps of the implementation of the virtual Mission Control Room in the Unity Game Engine. Overall, this paper serves as a demonstration of Virtual Reality technology and shows its possibilities with respect to the operation of spacecrafts.
Within this thesis a new philosophy in monitoring spacecrafts is presented: the
unification of the various kinds of monitoring techniques used during the
different lifecylce phases of a spacecraft.
The challenging requirements being set for this monitoring framework are:
- "separation of concerns" as a design principle (dividing the steps of logging
from registered sources, sending to connected sinks and displaying of
information),
- usage during all mission phases,
- usage by all actors (EGSE engineers, groundstation operators, etc.),
- configurable at runtime, especially regarding the level of detail of logging
information, and
- very low resource consumption.
First a prototype of the monitoring framework was developed as a support library
for the real-time operating system
RODOS. This prototype was tested on dedicated hardware platforms relevant for
space, and also on a satellite demonstrator used for educational purposes.
As a second step, the results and lessons learned from the development and usage
of this prototype were transfered to a real space mission: the first satellite
of the DLR compact satellite series - a space based platform for DLR's own
research activities. Within this project, the software of the avionic subsystem
was supplemented by a powerful logging component, which enhances the traditional
housekeeping capabilities and offers extensive filtering and debugging
techniques for monitoring and FDIR needs. This logging component is the major
part of the flight version of the monitoring framework. It is completed by
counterparts running on the development computers and as well as the EGSE
hardware in the integration room, making it most valuable already in the
earliest stages of traditional spacecraft development.
Future plans in terms of adding support from the groundstation as well will lead
to a seamless integration of the monitoring framework not only into to the
spacecraft itself, but into the whole space system.
Since the first CubeSat launch in 2003, the hardware and software complexity of the nanosatellites was continuosly increasing.
To keep up with the continuously increasing mission complexity and to retain the primary advantages of a CubeSat mission, a new approach for the overall space and ground software architecture and protocol configuration is elaborated in this work.
The aim of this thesis is to propose a uniform software and protocol architecture as a basis for software development, test, simulation and operation of multiple pico-/nanosatellites based on ultra-low power components.
In contrast to single-CubeSat missions, current and upcoming nanosatellite formation missions require faster and more straightforward development, pre-flight testing and calibration procedures as well as simultaneous operation of multiple satellites.
A dynamic and decentral Compass mission network was established in multiple active CubeSat missions, consisting of uniformly accessible nodes.
Compass middleware was elaborated to unify the communication and functional interfaces between all involved mission-related software and hardware components.
All systems can access each other via dynamic routes to perform service-based M2M communication.
With the proposed model-based communication approach, all states, abilities and functionalities of a system are accessed in a uniform way.
The Tiny scripting language was designed to allow dynamic code execution on ultra-low power components as a basis for constraint-based in-orbit scheduler and experiment execution.
The implemented Compass Operations front-end enables far-reaching monitoring and control capabilities of all ground and space systems.
Its integrated constraint-based operations task scheduler allows the recording of complex satellite operations, which are conducted automatically during the overpasses.
The outcome of this thesis became an enabling technology for UWE-3, UWE-4 and NetSat CubeSat missions.
An enduring engineering problem is the creation of unreliable software leading to unreliable systems. One reason for this is source code is written in a complicated manner making it too hard for humans to review and understand. Complicated code leads to other issues beyond dependability, such as expanded development efforts and ongoing difficulties with maintenance, ultimately costing developers and users more money.
There are many ideas regarding where blame lies in the reation of buggy and unreliable systems. One prevalent idea is the selected life cycle model is to blame. The oft-maligned “waterfall” life cycle model is a particularly popular recipient of blame. In response, many organizations changed their life cycle model in hopes of addressing these issues. Agile life cycle models have become very popular, and they promote communication between team members and end users. In theory, this communication leads to fewer misunderstandings and should lead to less complicated and more reliable code.
Changing the life cycle model can indeed address communications ssues, which can resolve many problems with understanding requirements.
However, most life cycle models do not specifically address coding practices or software architecture. Since lifecycle models do not address the structure of the code, they are often ineffective at addressing problems related to code complicacy.
This dissertation answers several research questions concerning software complicacy, beginning with an investigation of traditional metrics and static analysis to evaluate their usefulness as measurement tools. This dissertation also establishes a new concept in applied linguistics by creating a measurement of software complicacy based on linguistic economy. Linguistic economy describes the efficiencies of speech, and this thesis shows the applicability of linguistic economy to software. Embedded in each topic is a discussion
of the ramifications of overly complicated software, including the relationship of complicacy to software faults. Image recognition using machine learning is also investigated as a potential method of identifying problematic source code.
The central part of the work focuses on analyzing the source code of hundreds of different projects from different areas. A static analysis was performed on the source code of each project, and traditional software metrics were calculated. Programs were also analyzed using techniques developed by linguists to measure expression and statement complicacy and identifier complicacy. Professional software engineers were also directly surveyed to understand mainstream perspectives.
This work shows it is possible to use traditional metrics as indicators of potential project bugginess. This work also discovered it is possible to use image recognition to identify problematic pieces of source code. Finally, this work discovered it is possible to use linguistic methods to determine which statements and expressions are least desirable and more complicated for programmers.
This work’s principle conclusion is that there are multiple ways to discover traits indicating a project or a piece of source code has characteristics of being buggy. Traditional metrics and static analysis can be used to gain some understanding of software complicacy and bugginess potential. Linguistic economy demonstrates a new tool for measuring software complicacy, and machine learning can predict where bugs may lie in source code. The significant implication of this work is developers can recognize when a project is becoming buggy and take practical steps to avoid creating buggy projects.
Wireless communication networks already comprise an integral part of both the private and industrial sectors and are successfully replacing existing wired networks. They enable the development of novel applications and offer greater flexibility and efficiency. Although some efforts are already underway in the aerospace sector to deploy wireless communication networks on board spacecraft, none of these projects have yet succeeded in replacing the hard-wired state-of-the-art architecture for intra-spacecraft communication. The advantages are evident as the reduction of the wiring harness saves time, mass, and costs, and makes the whole integration process more flexible. It also allows for easier scaling when interconnecting different systems.
This dissertation deals with the design and implementation of a wireless network architecture to enhance intra-spacecraft communications by breaking with the state-of-the-art standards that have existed in the space industry for decades. The potential and benefits of this novel wireless network architecture are evaluated, an innovative design using ultra-wideband technology is presented. It is combined with a Medium Access Control (MAC) layer tailored for low-latency and deterministic networks supporting even mission-critical applications. As demonstrated by the Wireless Compose experiment on the International Space Station (ISS), this technology is not limited to communications but also enables novel positioning applications.
To adress the technological challenges, extensive studies have been carried out on electromagnetic compatibility, space radiation, and data robustness. The architecture was evaluated from various perspectives and successfully demonstrated in space.
Overall, this research highlights how a wireless network can improve and potentially replace existing state-of-the-art communication systems on board spacecraft in future missions. And it will help to adapt and ultimately accelerate the implementation of wireless networks in space systems.